1
|
Srikrishnarka P, Kumaran D, Kini AR, Kumar V, Nagar A, Islam MR, Nagarajan R, Pradeep T. Observing Real-Time Adhesion of Microparticles on Glass Surfaces. LANGMUIR : THE ACS JOURNAL OF SURFACES AND COLLOIDS 2023; 39:17071-17079. [PMID: 37971209 DOI: 10.1021/acs.langmuir.3c01856] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 11/19/2023]
Abstract
Fouling on glass surfaces reduces the solar panel efficiency and increases water consumption for cleaning. Superhydrophobic coatings on glass enable self-cleaning by allowing water droplets to carry away dirt particles. Observing the interaction between charged particles and surfaces provides insights into effective cleaning. Using a high-speed camera and a long-distance objective, we analyzed the in situ deposition of variously functionalized and charged silica dust microparticles on chemically treated glass. The ambient charges for the control, hydrophobic, and positively charged particles were approximately -0.5, -0.13, and +0.5 nC, respectively. We found that a positively charged particle of 2.3 ± 1.2 μm diameter adhered to hydroxylated glass in ∼0.054 s, compared to 0.40 and 0.45 s for quaternary ammonium- and fluorosilane-functionalized hydrophobic glass. Experiments suggest that quaternary ammonium-functionalized glass surfaces are about 77.8% more resistant to soiling than bare surfaces.
Collapse
Affiliation(s)
- Pillalamarri Srikrishnarka
- DST Unit of Nanoscience and Thematic Unit of Excellence, Department of Chemistry, Indian Institute of Technology Madras, Chennai 600036, India
- Department of Chemical Engineering, Indian Institute of Technology Madras, Chennai 600036, India
| | - Dhivyaraja Kumaran
- Department of Applied Mechanics, Indian Institute of Technology Madras, Chennai 600036, India
| | - Amoghavarsha Ramachandra Kini
- DST Unit of Nanoscience and Thematic Unit of Excellence, Department of Chemistry, Indian Institute of Technology Madras, Chennai 600036, India
| | - Vishal Kumar
- DST Unit of Nanoscience and Thematic Unit of Excellence, Department of Chemistry, Indian Institute of Technology Madras, Chennai 600036, India
- Department of Chemical Engineering, Indian Institute of Technology Madras, Chennai 600036, India
| | - Ankit Nagar
- DST Unit of Nanoscience and Thematic Unit of Excellence, Department of Chemistry, Indian Institute of Technology Madras, Chennai 600036, India
| | - Md Rabiul Islam
- DST Unit of Nanoscience and Thematic Unit of Excellence, Department of Chemistry, Indian Institute of Technology Madras, Chennai 600036, India
| | - Ramamurthy Nagarajan
- Department of Chemical Engineering, Indian Institute of Technology Madras, Chennai 600036, India
| | - Thalappil Pradeep
- DST Unit of Nanoscience and Thematic Unit of Excellence, Department of Chemistry, Indian Institute of Technology Madras, Chennai 600036, India
| |
Collapse
|
2
|
Dahlioui D, Alaoui SM, Laarabi B, Barhdadi A. Waterless cleaning technique for photovoltaic panels on dual-axis tracker. ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH INTERNATIONAL 2022:10.1007/s11356-022-23218-y. [PMID: 36227489 DOI: 10.1007/s11356-022-23218-y] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 04/03/2022] [Accepted: 09/19/2022] [Indexed: 06/16/2023]
Abstract
Several soiling mitigation solutions and cleaning techniques have been developed to maintain high efficiency of photovoltaic (PV) panels. First of its kind, the investigation of the adaptability of the cleaning systems to solar trackers has been performed. The majority of these systems are dedicated to fixed installations whereas only few systems that can be adapted to solar trackers are presented in the updated cleaning systems background. For this reason, this paper presents an innovative approach which consists of combining trackers with an integrated cleaning system that has been designed. Based on the conducted experimental study, a maximum of 7% in soiling losses has been found for the PV generator of 4 kWp equipped with a dual-axis tracker installed in Rabat-Morocco over almost 1 year. Consequently, a reduced cleaning prototype has been realized and tested to evaluate the energy recovery based on the performed cleaning. The automatic cleaning has presented a similar efficiency with the manual cleaning with a slight difference of 0.95 pp and an increase of energy of 11.5% in the arid region. Through the economic analysis carried out taking into account the gain in energy production, the automatic cleaning cost was 0.14 USD/kWh. It has been found that the cleaning technique based on the telescopic arm would be more effective if the tracker is installed in an arid region where soiling is higher than Rabat. In this case, the payback time of the cleaning solution is faster (8 to 9 years), hence its profitability.
Collapse
Affiliation(s)
- Dounia Dahlioui
- Physics of Semiconductors and Solar Energy Research Team (PSES), Energy Research Center, ENS, Mohammed V University in Rabat, Rabat, Morocco
| | - Soukaina Medaghri Alaoui
- Physics of Semiconductors and Solar Energy Research Team (PSES), Energy Research Center, ENS, Mohammed V University in Rabat, Rabat, Morocco
| | - Bouchra Laarabi
- Physics of Semiconductors and Solar Energy Research Team (PSES), Energy Research Center, ENS, Mohammed V University in Rabat, Rabat, Morocco
| | - Abdelfettah Barhdadi
- Physics of Semiconductors and Solar Energy Research Team (PSES), Energy Research Center, ENS, Mohammed V University in Rabat, Rabat, Morocco.
| |
Collapse
|
3
|
Efficiency Enhancement of an Ammonia-Based Solar Thermochemical Energy Storage System Implemented with Hydrogen Permeation Membrane. SUSTAINABILITY 2021. [DOI: 10.3390/su132212783] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 11/16/2022]
Abstract
The ammonia-based solar thermochemical energy storage (TCES) is one of the most promising solar TCESs. However, the solar-to-electric efficiency is still not high enough for further commercialization. The efficiency is limited by the high ammonia decomposition reaction temperature, which does not only increase the exergy loss through the heat recuperation but also causes a large re-radiation loss. Nonetheless, lowering the reaction temperature would impact the conversion and the energy storage capacity. Thanks to the recent development of the membrane technology, the hydrogen permeation membrane has the potential to enhance the conversion of ammonia decomposition under the moderate operating temperature. In this paper, an ammonia-based solar thermochemical energy storage system implemented with hydrogen permeation membrane is proposed for the first time. The system model has been developed using the Aspen Plus software implemented with user-defined Fortran subroutines. The model is validated by comparing model-generated reactor temperatures and conversions profiles with data from references. With the validated model, an exergy analysis is performed to investigate the main exergy losses of the system. Furthermore, the effects of the membrane on system efficiency improvement are studied. The results show that exergy loss in the charging loop is dominant, among which the exergy losses of Heat Exchanger Eh,A, together with that of the re-radiation Er, play important roles. Compared with the conventional system, i.e., the system without the membrane, the Eh,A and Er of the proposed system are more than 30% lower because the hydrogen permeation membrane can improve ammonia conversion at a lower endothermic reaction outlet temperature. Consequently, the proposed system, presumably realized by the parabolic trough collector at ~400 °C, has a theoretical solar-to-electric efficiency of ηste, which is 4.4% higher than the conventional ammonia-based solar thermochemical energy storage system. Last but not least, the efficiency is 3.7% higher than that of a typical parabolic trough solar power plant, which verifies the thermodynamic feasibility of further commercialization.
Collapse
|
4
|
Sarasua JA, Rubio LR, Aranzabe E, Vilela JLV. Energetic study of ultrasonic wettability enhancement. ULTRASONICS SONOCHEMISTRY 2021; 79:105768. [PMID: 34598103 PMCID: PMC8487089 DOI: 10.1016/j.ultsonch.2021.105768] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 06/07/2021] [Revised: 09/08/2021] [Accepted: 09/20/2021] [Indexed: 05/03/2023]
Abstract
Many industrial and biological interfacial processes, such as welding and breathing depend directly on wettability and surface tension phenomena. The most common methods to control the wettability are based on modifying the properties of the fluid or the substrate. The present work focuses on the use of high-frequency acoustic waves (ultrasound) for the same purpose. It is well known that ultrasound can effectively clean a surface by acoustic cavitation, hence ultrasonic cleaning technology. Besides the cleaning process itself, many authors have observed an important wettability enhancement when liquids are exposed to low and high (ultrasonic) frequency vibration. Ultrasound goes one step further as it can instantly adjust the contact angle by tuning the vibration amplitude, but there is still a lack of comprehension about the physical principles that explain this phenomenon. To shed light on it, a thermodynamic model describing how ultrasound decreases the contact angle in a three-phase wetting system has been developed. Moreover, an analytical and experimental research has been carried out in order to demonstrate that ultrasound is an important competitor to surfactants in terms of energy efficiency and environmental friendliness.
Collapse
Affiliation(s)
- Jon Ander Sarasua
- Tekniker, Basque Research and Technology Alliance (BRTA), C/Iñaki Goenaga 5, 20600 Eibar, Spain.
| | - Leire Ruiz Rubio
- Grupo de Química Macromolecular (LQM) Dpto. Química Física, Facultad de Ciencia y Tecnología, Universidad del País Vasco (UPV/EHU), 48940 Leioa, Spain
| | - Estibaliz Aranzabe
- Tekniker, Basque Research and Technology Alliance (BRTA), C/Iñaki Goenaga 5, 20600 Eibar, Spain
| | - Jose Luis Vilas Vilela
- Grupo de Química Macromolecular (LQM) Dpto. Química Física, Facultad de Ciencia y Tecnología, Universidad del País Vasco (UPV/EHU), 48940 Leioa, Spain
| |
Collapse
|
5
|
Soiling Comparison of Mirror Film and Glass Concentrating Solar Power Reflectors in Southwest Louisiana. SUSTAINABILITY 2021. [DOI: 10.3390/su13105727] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 11/16/2022]
Abstract
Soiling effects influence the output of solar thermal plants, significantly causing unwanted transmittance, reflectance, and absorbance losses. Research is needed to identify what type of reflective surfaces are best suited for semitropical climates, such as the southeastern United States. This paper initially presents a review of several concentrating solar power (CSP) reflector testbeds used to analyze the soiling effects of various reflective materials. A soiling testbed is developed for this study that comprised six sets of reflective surfaces mounted at a fixed tilt of 30 degrees: three sets of thin-film surfaces and three sets of glass types. Two generations of 3M solar mirror film (SMF), 3M SMF 1100 and 3M SMF 2020, were used along with Konica Minolta SMF, silvered Corning Willow Glass, a dichroic cold mirror, and a standard mirror. Results show that the 3M SMF 2020 and Konica Minolta SMF performed the best during regular cleaning intervals, whereas the silvered Corning Willow Glass gave the best performance if only cleaned naturally. The other glass types showed the least average loss due to soiling throughout this study but gave the lowest performance for specular reflection.
Collapse
|
6
|
Non-Immersion Ultrasonic Cleaning: An Efficient Green Process for Large Surfaces with Low Water Consumption. Processes (Basel) 2021. [DOI: 10.3390/pr9040585] [Citation(s) in RCA: 3] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/30/2022] Open
Abstract
Ultrasonic cleaning is a developed and widespread technology used in the cleaning industry. The key to its success over other cleaning methods lies in its capacity to penetrate seemingly inaccessible, hard-to-reach corners, cleaning them successfully. However, its major drawback is the need to immerse the product into a tank, making it impossible to work with large or anchored elements. With the aim of revealing the scope of the technology, this paper will attempt to describe a more innovative approach to cleaning large area surfaces (walls, floors, façades, etc.) which involves applying ultrasonic cavitation onto a thin film of water, which is then deposited onto a dirty surface. Ultrasonic cleaning is an example of the proliferation of green technology, requiring 15 times less water and 115 times less power than conventional high-pressurized waterjet cleaning mechanisms. This paper will account for the physical phenomena that govern this new cleaning mechanism and the competition it poses towards more conventional pressurized waterjet technology. Being easy to use as a measure of success, specular surface cleaning has been selected to measure the degree of cleanliness (reflectance) as a function of the process’s parameters. A design of experiments has been developed in line with the main process parameters: amplitude, gap, and sweeping speed. Regression models have also been used to interpret the results for different degrees of soiling. The work concludes with the finding that the proposed new cleaning technology and process can reach up to 98% total cleanliness, without the use of any chemical product and with very low water and power consumption.
Collapse
|
7
|
Sustainable Wastewater Treatment and Utilization: A Conceptual Innovative Recycling Solution System for Water Resource Recovery. SUSTAINABILITY 2020. [DOI: 10.3390/su122410350] [Citation(s) in RCA: 3] [Impact Index Per Article: 0.8] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 11/16/2022]
Abstract
The global demand for drinking water is increasing day by day. Different methods are used for desalination of water, which can help in the conservation of resources, such as seawater, highly saline, or treated water underground reservoirs. Polluted water can be treated by the utilization of different advanced techniques. In this study, wastewater mixed canal water has been taken into consideration for the utilization of humans and agriculture use as well. A two-stage conceptual methodology has been proposed to deal with the water conservation and utilization process. In the first phase, power has been produced using a Belgian vortex turbine, which is a safe, efficient, and eco-friendly technology working without disturbing waterways. The power produced by the vortex machine will be utilized to operate the water treatment plant to obtain clean water for utilization in the second phase. Since enough energy is produced, and its availability to the water head level base is a natural resource, this energy can be used to fulfill daily water requirements by maximizing the energy-driven treatment process as per WHO Guidelines. Water quality can be monitored at regular intervals, depending upon the selection and installation of a treatment plant. An increase in efficiency comes from nearly exponential patterns depending on water velocity and availability. This technique will not only help in the production of clean water but will also help in the conservation of groundwater resources and the efficient utilization of wastewater.
Collapse
|
8
|
Sustainability Outcomes of Green Processes in Relation to Industry 4.0 in Manufacturing: Systematic Review. SUSTAINABILITY 2020. [DOI: 10.3390/su12155968] [Citation(s) in RCA: 26] [Impact Index Per Article: 6.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 12/23/2022]
Abstract
Green processes are very important for the implementation of green technologies in production to achieve positive sustainability outcomes in the Industry 4.0 era. The scope of the paper is to review how conventional green processes as a part of Industry 4.0 provide sustainability outcomes in manufacturing. The paper is based on the methodology of systematic literature review through the content analysis of literary resources. Twenty-nine studies were included in our content analysis. The results show the main focus of current literature related to Industry 4.0, sustainability outcomes and green processes. The authors present a conceptual Sustainability Green Industry 4.0 (SGI 4.0) framework that helps to structure and evaluate conventional green processes in relation to Industry 4.0 and sustainability. The study summarizes which technologies (big data, cyber-physical systems, Industrial Internet of Things and smart systems) and green processes (logistics, manufacturing and product design) are important for achieving a higher level of sustainability. The authors found that the most often common sustainability outcomes are energy saving, emission reduction, resource optimalization, cost reduction, productivity and efficiency and higher economic performance, human resources development, social welfare and workplace safety. The study suggests implications for practice, knowledge and future research.
Collapse
|
9
|
Assessment of Existing Photovoltaic System with Cooling and Cleaning System: Case Study at Al-Khobar City. Processes (Basel) 2019. [DOI: 10.3390/pr8010009] [Citation(s) in RCA: 13] [Impact Index Per Article: 2.6] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/16/2022] Open
Abstract
There is no denial that renewable energy is considered to be the most cost-competitive source of clean power in many parts of the world. Saudi Arabia’s vision 2030 aims at achieving the best by using different sources of renewable energy such as solar energy, wind energy, and others. The use of solar energy in particular for power generation will decrease the dependency on oil, and thus, decrease the greenhouse gasses. Solar panels efficiency tends to decrease with the accumulation of dust on their surface. Thus, a cleaning process requires assigning and employing labor, which increases the cost of running as well as high cost of machinery. The current study focuses on assessing and designing a simple auto self-cleaning system in order to improve the efficiency of the solar panel. The results showed that for the Al-Khobar region, Eastern Province, Kingdom of Saudi Arabia, the efficiency of the solar panels after cleaning was increased from 6% to an average of 12% at nominal temperature of 27 °C. In addition, the average power output was increased by 35% during the day time. In addition, the normal efficiency of the solar panels before cooling was between 10% to 15% at 42 °C. After cooling, the temperature of solar cells decreased to 20 °C and the efficiency increased by 7%. Moreover, the output power was increased by 31% with maximum efficiency of 32% at noon time.
Collapse
|
10
|
Water Saving in CSP Plants by a Novel Hydrophilic Anti-Soiling Coating for Solar Reflectors. COATINGS 2019. [DOI: 10.3390/coatings9110739] [Citation(s) in RCA: 7] [Impact Index Per Article: 1.4] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 11/17/2022]
Abstract
In this work, results of the outdoor exposure campaign of a newly developed hydrophilic anti-soiling coating for concentrated solar thermal power (CSP) mirrors are presented. The material was exposed for nearly two years under realistic outdoor conditions and the influence of two different cleaning techniques was evaluated. Mirror samples were analyzed during exposure and their reflectance and cleanliness were measured. The performance of the anti-soiling coated mirror samples was compared to conventional uncoated silvered-glass mirrors. The coatings showed appropriate anti-soiling and easy-to-clean behavior, with a mean cleanliness gain of 1 pp and maximum values under strong soiling conditions of up to over 7 pp. Cleanliness of the coated samples stayed higher throughout the whole campaign before and after cleaning, resulting in lower soiling rate compared to the reference material. Taking into account these values and supposing a threshold for cleaning of 96%, the number of cleaning cycles could be decreased by up to 11%. Finally, the coated material showed negligible degradation, not exceeding the degradation detected for the reference material.
Collapse
|
11
|
Soiling of Photovoltaic Modules: Comparing between Two Distinct Locations within the Framework of Developing the Photovoltaic Soiling Index (PVSI). SUSTAINABILITY 2019. [DOI: 10.3390/su11174697] [Citation(s) in RCA: 14] [Impact Index Per Article: 2.8] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 11/17/2022]
Abstract
This article evaluates the impact of dust accumulation on the performance of photovoltaic (PV) modules in two different locations inside Egypt, Cairo and Beni-Suef. Two identical PV modules were used for that purpose, where each module was exposed to the outdoor environment in order to collect dust naturally for a period of three weeks, each in its corresponding location. The approximate dust density on each of the two PV modules was estimated. Moreover, the electrical performance was evaluated and compared under the same indoor testing conditions. The results show a better electrical performance and less dust density for the PV module located in Cairo compared to that located in Beni-Suef. The results further provide an indication for the impact of soling in different locations within the same country through a clear and simple procedure. In addition, it paves the way for establishing a Photovoltaic Soiling Index (PVSI) in terms of a Photovoltaic Dust Coefficient, as well as a Photovoltaic Dust Interactive Map. The product of such concepts could be used by the Photovoltaic systems designers everywhere in order to estimate the impact of dust on the future performance of PV modules in small and large installations in different regions around the globe, and during different times of the year as well.
Collapse
|