Organic Fouling in Forward Osmosis: A Comprehensive Review

Advancement of membrane separation technology for organic pollutant removal

In the face of growing global freshwater scarcity, the imperative to recycle and reuse water becomes increasingly apparent across industrial, agricultural, and domestic sectors. Eliminating a range of organic pollutants in wastewater, from pesticides to industrial byproducts, presents a formidable challenge. Among the potential solutions, membrane technologies emerge as promising contenders for treating diverse organic contaminants from industrial, agricultural, and household origins. This paper explores cutting-edge membrane-based approaches, including reverse osmosis, nanofiltration, ultrafiltration, microfiltration, gas separation membranes, and pervaporation. Each technology's efficacy in removing distinct organic pollutants while producing purified water is scrutinized. This review delves into membrane fouling, discussing its influencing factors and preventative strategies. It sheds light on the merits, limitations, and prospects of these various membrane techniques, contributing to the advancement of wastewater treatment. It advocates for future research in membrane technology with a focus on fouling control and the development of energy-efficient devices. Interdisciplinary collaboration among researchers, engineers, policymakers, and industry players is vital for shaping water purification innovation. Ongoing research and collaboration position us to fulfill the promise of accessible, clean water for all.

Biofouling mechanism and cleaning procedures for Spirulina platensis as an organic fertilizer draw solution

The forward osmosis (FO) desalination process has recently acknowledged a lot of attention as a promising solution for reducing the disadvantages of existing desalination systems. This work aimed to investigate the effect of a selected liquid organic fertilizer a novel draw solution produced from "microalgae Spirulina platensis" on the biofouling mechanism of FO membrane. Different draw solution (DS) concentrations ranging 240-480 g/L were examined, obtained water flux ranging from 6.5 to 3.4 Lm2h-1. A high flux decline was observed when using higher DS concentrations due to fouling layer accumulated throughout the membrane area which lowers the effective osmotic pressure difference. Different cleaning strategies were examined. The biofouled membrane was cleaned on-line with deionized water (DI) and externally using ultrasound (US) and HCl. Baseline experiments were done to investigate the efficiency of the cleaning strategies. After cleaning using the deionized water (DI) water, it was found that the water flux progressed from 3.4 to 7 Lm2h-1, while when using acid cleaning the flux recovered to 15 Lm-2h-1. The efficacy and amount of foulant removed by each cleaning stage were assessed using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX).

Fouling in reverse osmosis membranes: monitoring, characterization, mitigation strategies and future directions

Water scarcity has been a global challenge for many countries over the past decades, and as a result, reverse osmosis (RO) has emerged as a promising and cost-effective tool for water desalination and wastewater remediation. Currently, RO accounts for >65% of the worldwide desalination capacity; however, membrane fouling is a major issue in RO processes. Fouling reduces the membrane's lifespan and permeability, while also increases the operating pressure and chemical cleaning frequency. Overall, fouling reduces the quality and quantity of desalinated water, and thus hinders the sustainable application of RO membranes by disturbing its efficacy and economic aspects. Fouling arises from various physicochemical interactions between water pollutants and membrane materials leading to foulants' accumulation onto the membrane surfaces and/or inside the membrane pores. The current review illustrates the main types of particulates, organic, inorganic and biological foulants, along with the major factors affecting its formation and development. Moreover, the currently used monitoring methods, characterization techniques and the potential mitigation strategies of membrane fouling are reviewed. Further, the still-faced challenges and the future research on RO membrane fouling are addressed.

Design Strategies for Forward Osmosis Membrane Substrates with Low Structural Parameters-A Review

This article reviews the many innovative strategies that have been developed to specifically design the support layers of forward osmosis (FO) membranes. Forward osmosis (FO) is one of the most viable separation technologies to treat hypersaline wastewater, but its successful deployment requires the development of new membrane materials beyond existing desalination membranes. Specifically, designing the FO membrane support layers requires new engineering techniques to minimize the internal concentration polarization (ICP) effects encountered in cases of FO. In this paper, we have reviewed several such techniques developed by different research groups and summarized the membrane transport properties corresponding to each approach. An important transport parameter that helps to compare the various approaches is the so-called structural parameter (S-value); a low S-value typically corresponds to low ICP. Strategies such as electrospinning, solvent casting, and hollow fiber spinning, have been developed by prior researchers-all of them aimed at lowering this S-value. We also reviewed the quantitative methods described in the literature, to evaluate the separation properties of FO membranes. Lastly, we have highlighted some key research gaps, and provided suggestions for potential strategies that researchers could adopt to enable easy comparison of FO membranes.

A novel conductive carbon-based forward osmosis membrane for dye wastewater treatment

Forward osmosis (FO) membrane fouling is one of the main reasons that hinder the further application of FO technology in the treatment of dye wastewater. To alleviate membrane fouling, a conductive coal carbon-based substrate and polydopamine nanoparticles (PDA NPs) interlayer composite FO membrane (CPFO) was prepared by interfacial polymerization (IP). CPFO-10 membrane prepared by depositing 10 mL of PDA NPs solution exhibited an optimum performance with water flux of 7.56 L/(m²h) for FO mode and 10.75 L/(m²h) for pressure retarded osmosis (PRO) mode, respectively. For rhodamine B and chrome black T dye wastewater treatment, the water flux losses were reduced by 21.6%, and 14.5% under the voltages of +1.5 V, and -1.5 V, respectively, compared with no voltage applied after the device was operated for 8 h. The applied voltage had little effect on the fouling mitigation performance of the CPFO membrane for neutral charged cresol red. After the device was operated for 4 cycles, the rejection rates of dyes wastewater treated by the CPFO membranes with applied voltage were close to 100%. The flux decline rate and flux recovery rate of CPFO membrane for rhodamine B and chrome black T wastewater treatment under application of +1.5 V and -1.5 V voltage after 4 cycles were 11.6%, 99.2%, and 16.7%, 98.9%, respectively. Therefore, the voltage-applied CPFO membrane still maintained good rejection and antifouling performance in long-term operation. This study provides a new insight into the preparation of conductive FO membranes for dye wastewater treatment and membrane fouling control.

Forward Osmosis Membranes: The Significant Roles of Selective Layer

Forward osmosis (FO) is a promising separation technology to overcome the challenges of pressure-driven membrane processes. The FO process has demonstrated profound advantages in treating feeds with high salinity and viscosity in applications such as brine treatment and food processing. This review discusses the advancement of FO membranes and the key membrane properties that are important in real applications. The membrane substrates have been the focus of the majority of FO membrane studies to reduce internal concentration polarization. However, the separation layer is critical in selecting the suitable FO membranes as the feed solute rejection and draw solute back diffusion are important considerations in designing large-scale FO processes. In this review, emphasis is placed on developing FO membrane selective layers with a high selectivity. The effects of porous FO substrates in synthesizing high-performance polyamide selective layer and strategies to overcome the substrate constraints are discussed. The role of interlayer in selective layer synthesis and the benefits of nanomaterial incorporation will also be reviewed.

Fouling and Performance Investigation of Membrane Distillation at Elevated Recoveries for Seawater Desalination and Wastewater Reclamation

This study reports on the impact of elevated recovery (i.e., 80%, 85%, and 90%) on the fouling and performance of air gap membrane distillation (AGMD) with real seawater and landfill leachate wastewater samples using polytetrafluoroethylene (PTFE) polymer membranes. Increasing the feed temperature from 55 °C to 65 °C improved the water flux of seawater and wastewater and shortened the operating time by 42.8% for all recoveries. The average water flux in the 80%, 85%, and 90% recovery experiments at the 65 °C feed temperature was 32%, 37.32%, and 36.7% higher than the case of 55 °C for the same recoveries. The water flux decline was more severe at a higher temperature and recovery. The highest flux decline was observed with a 90% recovery at 65 °C feed temperature, followed by an 85% recovery at 65 °C. Close examination of the foulants layer revealed that seawater formed a cake fouling layer made predominantly of metal oxides. In contrast, the landfill leachate fouling was a combination of pore blocking and cake formation, consisting mainly of carbonous and nitrogenous compounds. Physical cleaning with deionized (DI) water at 55 °C and 65 °C and chemical cleaning with hydrogen peroxide (H2O2) were investigated for their efficiency in removing membrane foulants. Analytical results revealed that seawater fouling caused membrane pore blockage while wastewater fouling formed a porous layer on the membrane surface. The results showed that membrane cleaning with hydrogen peroxide restored >97% of the water flux. Interestingly, the fouling factor in seawater tests was 10%, while it was 16% for the wastewater tests.

A Review on the Development of an Integer System Coupling Forward Osmosis Membrane and Ultrasound Waves for Water Desalination Processes

This review considers the forward osmosis (FO) membrane process as one of the feasible solutions for water desalination. Different aspects related to the FO process are reviewed with an emphasis on ultrasound assisted FO membrane processes. The different types of membranes used in FO are also reviewed and discussed; thus, their configuration, structure and applications are considered. Coupling ultrasound with FO enhances water flux through the membrane under certain conditions. In addition, this review addresses questions related to implementation of an ultrasound/FO system for seawater desalination, such as the impact on fouling, flow configuration, and location of fouling. Finally, the mechanisms for the impact of ultrasound on FO membranes are discussed and future research directions are suggested.

Preparation of fouling resistant and highly perm-selective novel PSf/GO-vanillin nanofiltration membrane for efficient water purification

To meet the rising global demand for water, it is necessary to develop membranes capable of efficiently purifying contaminated water sources. Herein, we report a series of novel polysulfone (PSf)/GO-vanillin nanofiltration membranes highly permeable, selective, and fouling resistant. The membranes are composed of two-dimensional (2D) graphite oxide (GO) layers embedded with vanillin as porogen and PSf as the base polymer. There is a growing interest in addressing the synergistic effect of GO and vanillin on improving the permeability and antifouling characteristics of membranes. Various spectroscopic and microscopic techniques were used to perform detailed physicochemical and morphological analyses. The optimized PSf₁₆/GO_0.15-vanillin_0.8 membrane demonstrated 92.5% and 25.4% rejection rate for 2000 ppm magnesium sulphate (MgSO₄) and sodium chloride (NaCl) solutions respectively. Antifouling results showed over 99% rejection for BSA and 93.57% flux recovery ratio (FRR). Experimental work evaluated the antifouling characteristics of prepared membranes to treat landfill leachate wastewater. The results showed 84-90% rejection for magnesium (Mg⁺²) and calcium (Ca⁺²) with 90.32 FRR. The study experimentally demonstrated that adding GO and vanillin to the polymeric matrix significantly improves fouling resistance and membrane performance. Future research will focus on molecular sieving for industrial separations and other niche applications using mixed matrix membranes.

Multi-Integrated Systems for Treatment of Abattoir Wastewater: A Review

Biological wastewater treatment processes such as activated sludge and anaerobic digestion remain the most favorable when compared to processes such as chemical precipitation and ion exchange due to their cost-effectiveness, eco-friendliness, ease of operation, and low maintenance. Since Abattoir Wastewater (AWW) is characterized as having high organic content, anaerobic digestion is slow and inadequate for complete removal of all nutrients and organic matter when required to produce a high-quality effluent that satisfies discharge standards. Multi-integrated systems can be designed in which additional stages are added before the anaerobic digester (pre-treatment), as well as after the digester (post-treatment) for nutrient recovery and pathogen removal. This can aid the water treatment plant effluent to meet the discharge regulations imposed by the legislator and allow the possibility for reuse on-site. This review aims to provide information on the principles of anaerobic digestion, aeration pre-treatment technology using enzymes and a hybrid membrane bioreactor, describing their various roles in AWW treatment. Simultaneous nitrification and denitrification are essential to add after anaerobic digestion for nutrient recovery utilizing a single step process. Nutrient recovery has become more favorable than nutrient removal in wastewater treatment because it consumes less energy, making the process cost-effective. In addition, recovered nutrients can be used to make nutrient-based fertilizers, reducing the effects of eutrophication and land degradation. The downflow expanded granular bed reactor is also compared to other high-rate anaerobic reactors, such as the up-flow anaerobic sludge blanket (UASB) and the expanded granular sludge bed reactor (EGSB).

Synthesizing Various Organic Polyacid Compounds for Modifying Forward Osmosis Membranes to Enhance Separation Performance

In order to overcome the challenges of low permeate flux (J_p) and the accompanying reverse solute flux (J_S) during the forward osmosis (FO) membrane separation process, we synthesized four hybrid materials of polyacid-based organic compounds and incorporated them into the selective polyamide (PA) layer to make novel thin-film nanocomposite (TFN) FO membranes. The J_p and J_S of each membrane were evaluated and used along with membrane selectivity (J_p/J_S) as indicators of membrane separation performance. The fabricated and modified membranes were also characterized for ridge and valley surface morphologies with increasing hydrophilicity and finger-shaped parallel channels in the PSf substrate. Moreover, two highly hydrophilic nanoparticles of graphene oxide (GO) and titanium oxide (TiO₂) were introduced with the hybrid materials for PA modification, which can further enhance the J_p of the TFN membranes. The highest J_p of the TFN membranes achieved 12.1 L/m²-h using 0.1% curcumin-acetoguanamine @ cerium polyacid (CATCP) and 0.0175% GO. The characteristic peaks of the hybrid materials were detected on the membrane surface using attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy, evidencing successful incorporation of the hybrid materials during membrane modification. Here, we present the novel TFN membranes using hybrid materials for separation applications. The reactions for synthesizing the hybrid materials and for incorporating them with PA layer are proposed.

Application of Zwitterions in Forward Osmosis: A Short Review

Forward osmosis (FO) is an important desalination method to produce potable water. It was also used to treat different wastewater streams, including industrial as well as municipal wastewater. Though FO is environmentally benign, energy intensive, and highly efficient; it still suffers from four types of fouling namely: organic fouling, inorganic scaling, biofouling and colloidal fouling or a combination of these types of fouling. Membrane fouling may require simple shear force and physical cleaning for sufficient recovery of membrane performance. Severe fouling may need chemical cleaning, especially when a slimy biofilm or severe microbial colony is formed. Modification of FO membrane through introducing zwitterionic moieties on the membrane surface has been proven to enhance antifouling property. In addition, it could also significantly improve the separation efficiency and longevity of the membrane. Zwitterion moieties can also incorporate in draw solution as electrolytes in FO process. It could be in a form of a monomer or a polymer. Hence, this review comprehensively discussed several methods of inclusion of zwitterionic moieties in FO membrane. These methods include atom transfer radical polymerization (ATRP); second interfacial polymerization (SIP); coating and in situ formation. Furthermore, an attempt was made to understand the mechanism of improvement in FO performance by zwitterionic moieties. Finally, the future prospective of the application of zwitterions in FO has been discussed.

Electrically Polarized Graphene-Blended Spacers for Organic Fouling Reduction in Forward Osmosis

In membrane processes, a spacer is known to play a key role in the mitigation of membrane fouling. In this study, the effect of electric polarization on a graphene-blended polymer spacer (e.g., poly(lactic acid), PLA) for organic fouling on membrane surfaces was investigated. A pristine PLA spacer (P-S), a graphene-blended spacer (G-S), and an electrically polarized graphene-blended spacer (EG-S) were successfully fabricated by 3D printing. Organic fouling tests were conducted by the 5-h filtration of CaCl₂ and a sodium alginate solution through commercially available membranes, which were placed together with the fabricated spacers. Membranes utilizing P-S, G-S, and EG-S were characterized in terms of the fouling amount on the membrane surface and fouling roughness. Electrostatic forces of EG-S provided 70% less and 90% smoother fouling on the membrane surface, leading to an only 14% less water flux reduction after 5 h of fouling. The importance of nanomaterial blending and polarization was successfully demonstrated herein.

Feasibility of brackish water and landfill leachate treatment by GO/MoS2-PVA composite membranes

Two-dimensional (2D) based layered materials with tunable chemical functionalities and surface charge properties have emerged for on-demand applications including membrane technology. However, the process control, time and energy-efficient production of non-swelling graphene oxide (GO) with retaining physicochemical properties are still challenging. In this work, we have fabricated highly ordered GO membrane on cellulose acetate supporting membrane filters of 1.2 μm pore size using molybdenum disulphide (MoS₂) as a nano-spacer and polyvinyl alcohol (PVA) as an adhesive for the first time with limited swelling. The fabricated membranes were used for NaCl rejection and removal of toxic heavy metal ions, and the radioactive element from landfill leachate water. The introduction of hydrophilic PVA, thickness control using a various amount of nanospacer and graphene oxide played a vital role in the transport mechanism, permeability, and selectivity index. The composition of PVA and MoS₂ in the coating solution was optimized to tune the d-spacing of graphene oxide layers. The newly developed composite membranes have 89% rejection rate to NaCl and 3.96 L/m²h water flux at low operating pressures of 5 bar. Also, the prepared membranes have a high rejection of multivalent metal ions in landfill leachate. 86.5% to 99.8% rejection rate of multivalent metal ions in landfill leachate was observed for the M₃ (GO ₍₁₀₎: MoS_{2 (10)}: PVA _(0.5)) membrane. The excellent rejection performance is ascribed to the combined impact of size exclusion, ion adsorption, electrostatic interaction and Gibbs-Donnan exclusion mechanism. The excellent stability and high rejection rate even after 216 h of operation make the fabricated membranes promising for use in practical water separation applications.

Treatment of biologically treated landfill leachate with forward osmosis: Investigating membrane performance and cleaning protocols

This study presents systematic investigations to evaluate the performance, rejection rate, fouling, cleaning protocols and impact of physical and chemical cleaning strategies on the performance of commercial cellulose triacetate (CTA) membrane. The treatment of landfill leachate (LFL) solution was performed in the active layer facing feed solution and support layer facing the draw solution (AL-FS mode), and active layer facing the draw solution and support layer facing the feed solution (AL-DS mode). Compared to the AL-FS mode, a higher flux for AL-DS mode was achieved, but membrane fouling was more severe in the latter. In both membrane orientations, the rejection rate of the FO membrane to heavy ions and contaminants in the wastewater was between 93 and 99%. Physical and chemical cleaning strategies were investigated to recover the performance of the FO membrane and to study the impact of cleaning methods on the membrane rejection rate. Physical cleaning with hot water at 35 °C and osmotic backwashing with 1.5 M NaCl demonstrated excellent water flux recovery compared to chemical cleaning. In the chemical cleaning, an optimal concentration of 3% hydrogen peroxide was determined for 100% flux recovery of the fouled membrane. However, slight membrane damage was achieved at this concentration on the active layer side. Alkaline cleaning at pH 11 was more effective than acid cleaning at pH 4, although both protocols compromised the membrane rejection rate for some toxic ions. A comparison of the membrane long-term performance found that cleaning with osmotic backwashing and hot water were effective methods to restore water flux without comprising the membrane rejection rate. Overall, it was found that physical cleaning protocols are superior to chemical cleaning protocols for forward osmosis membrane fouled by landfill leachate wastewater.

Seawater Desalination: A Review of Forward Osmosis Technique, Its Challenges, and Future Prospects

Currently over 845 million people are believed to be living under severe water scarcity, and an estimated 2.8 billion people across the globe are projected to come under serious water scarcity by the year 2025, according to a United Nations (UN) report. Seawater desalination has gained more traction as the solution with the most potential for increasing global freshwater supplies amongst other solutions. However, the economic and energy costs associated with the major desalination technologies are considered intrinsically prohibitive largely due to their humongous energy requirements alongside the requirements of complex equipment and their maintenance in most cases. Whilst forward osmosis (FO) is being touted as a potentially more energy efficient and cost-effective alternative desalination technique, its efficiency is challenged by draw solutes and the draw solutes recovery step in FO applications alongside other challenges. This paper looks at the present situation of global water scarcity, and a brief leap into the major desalination technologies employed. A closer look at the key drivers of FO as a seawater desalination technique in their individual domain and its outlook as an technology are further highlighted.