Tetracycline Degradation by Peroxydisulfate Activated by Waste Pulp/Paper Mill Sludge Biochars Derived at Different Pyrolysis Temperature

Elucidating the roles of Ni ions and crosslinking heteroatoms in Ni3(BHT)2/2GO as electron shuttles for electrocatalytic oxidation of tetracycline hydrochloride

As a hot candidate for marine pollution control, electrocatalytic oxidation strongly depends on the characteristics of anode materials. Even though emerging 2D metal-organic frameworks (2D-MOFs)/graphene oxide (GO) complex has satisfied the conductive and tunable requirements of anode, electrocatalytic efficiency still needs to be improved by maximizing the electron carriers or shuttles. Herein, we capitalized upon crosslinking heteroatoms as pointcut to adjust the electron distribution, mobility, and transfer orientation in 2D-MOFs/GO. As a result, Ni3(BHT)2/2GO (metal centers: Ni; crosslinking heteroatoms: S), which was much higher than materials with metal centers of Cu or crosslinking heteroatoms of N, achieved superior conductivity and 100% tetracycline hydrochloride removal within 12 min. In Ni3(BHT)2/2GO, Ni ions and S atoms cooperated as electron shutters rather than isolated active center and granted accelerated electron transfer from 2D-MOFs to GO layers. Furthermore, Ni sites and S crosslinking heteroatoms exhibited superior activity for ⋅O2- and ⋅OH generation, whereas 1O2 depended more on C and O substrates. All experiments, theory calculations, and application expanding approved the practice feasibility of 2D-MOFs/GO in electrocatalytic oxidation by adjusting crosslinking heteroatoms. All these results provided new perspectives on the micro-molecular regulation for improving electrocatalytic efficiency.

Recycled pulp and paper sludge, potential source of cellulose: feasibility assessment and characterization

The pulp and paper industry stands out as an example of a technology based on a renewable resource, cellulose. The sludge, however, poses major environmental and public health problems. To effectively manage the sludge wastes, it is critical to fully evaluate its composition, possible environmental impacts, and the total amount of exploitable renewable resources. The study established the pH of the sludge to be 7.32 ± 0.98, an electrical conductivity (1.84 mS/cm), nitrogen concentration (2.65 ± 0.21%), and total organic matter (41.23 ± 3.11%). The cellulosic content was established to be 74.07 ± 2.71% which contributes to 53.07 ± 1.23% water holding capacity (WHC). The most abundant elements were C and O, followed by Cl, Si, Al, and Mg, with lower concentrations of S, Si, K, and iron. The polycyclic aromatic compounds (PAHs) levels ranged from 0.29 to 322.56 ng.g-1 with 1-methyl pyrene posting the highest concentration (322.56 ng.g-1. XRD peaks at 17.10°, 23.86°, 30.14°, and 36.57°, which imply the existence of CaCO3. SEM indicated that the sludge was majorly comprised of fibers materials with average particle sizes of 280 micrometers. TGA/DTG analysis showed that the sludge had the greatest cellulose and hemicellulose (64.7 wt. %).

Preparation and Characterization of Pulp and Paper Mill Sludge-Activated Biochars Using Alkaline Activation: A Box-Behnken Design Approach

This study utilized pulp and paper mill sludge as a carbon source to produce activated biochar adsorbents. The response surface methodology (RSM) application for predicting and optimizing the activated biochar preparation conditions was investigated. Biochars were prepared based on a Box-Behnken design (BBD) approach with three independent factors (i.e., pyrolysis temperature, holding time, and KOH:biomass ratio), and the responses evaluated were specific surface area (SSA), micropore area (S _micro), and mesopore area (S _meso). According to the RSM and BBD analysis, a pyrolysis temperature of 800 °C for 3 h of holding and an impregnation ratio of 1:1 (biomass:KOH) are the optimum conditions for obtaining the highest SSA (885 m² g^-1). Maximized S _micro was reached at 800 °C, 1 h and the ratio of 1:1, and for maximizing S _meso (569.16 m² g^-1), 800 °C, 2 h and ratio 1:1.5 (445-473 m² g^-1) were employed. The biochars presented different micro- and mesoporosity characteristics depending on pyrolysis conditions. Elemental analysis showed that biochars exhibited high carbon and oxygen content. Raman analysis indicated that all biochars had disordered carbon structures with structural defects, which can boost their properties, e.g., by improving their adsorption performances. The hydrophobicity-hydrophilicity experiments showed very hydrophobic biochar surfaces. The biochars were used as adsorbents for diclofenac and amoxicillin. They presented very high adsorption performances, which could be explained by the pore filling, hydrophobic surface, and π-π electron-donor-acceptor interactions between aromatic rings of both adsorbent and adsorbate. The biochar with the highest surface area (and highest uptake performance) was subjected to regeneration tests, showing that it can be reused multiple times.