Effect of copper salts added to primer on bonding of MMA-TBB resin to dentin treated with phosphoric acid

Adhesive bonding to dentin with iron (II) perchlorate primers and a tri-n-butylborane-initiated luting agent

OBJECTIVES

This study was conducted to measure the tensile bond strength of a resin to dentin when the dentin was primed with iron (II) perchlorate modified aqueous 2-hydroxyethyl methacrylate (HEMA) or an iron (II) perchlorate modified commercial self-etching primer (ED primer, Kuraray Co.).

METHODS

Bovine dentin surfaces were ground flat and each specimen underwent one of the following two treatments: (1) priming with 2.0 x 10(-6) to 5.0 x 10(-4) mol/g iron (II) perchlorate in aqueous HEMA solutions after etching with 10 wt% phosphoric acid; (2) priming with self-etching primers containing 4.0 x 10(-7) to 2.0 x 10(-4) mol/g iron (II) perchlorate. Each specimen was then bonded to a stainless-steel rod with a luting agent (MMA-TBB resin) consisting of methyl methacrylate (MMA), poly(methyl methacrylate) (PMMA), and tri-n-butylborane (TBB) initiator. Tensile strengths of the bonded tooth specimens were then determined after 1 day immersion in water. Results were analyzed using ANOVA and Duncan's new multiple range test (p < 0.05).

RESULTS

Tensile testing revealed the maximum mean bond strengths (22.5 MPa) when the dentin was primed with 2.0 x 10(-4) mol/g iron (II) perchlorate after etching with 10 wt% phosphoric acid aqueous solution. The highest level of bond strength with self-etching primer (19.6 MPa) was achieved using 1.0 x 10(-4) mol/g iron (II) perchlorate.

SIGNIFICANCE

These bonding techniques, combining the use of iron (II) perchlorate modified HEMA primers with MMA-TBB resin, are potentially applicable for seating resin-bonded restorations.

Metal chloride primers for bonding dentine with tri-n-butylborane-initiated luting agents

OBJECTIVES

The bonding of resin to dentine is dependent largely on surface modifications. The purpose of the present study was to test the hypothesis that a role of the metal chlorides used as primers is to initiate polymerization of resin at the resin-dentine interface, thereby affecting bond strength.

METHODS

Nine primers were evaluated, comprising aqueous 2-hydroxyethyl methacrylate (HEMA) solutions containing AICl3, CeCl3, CoCl2, CuCl2, FeCl3, NiCl2, MgCl2, SnCl2 or ZnCl2, respectively. One of the two luting agents (Super-Bond resin) consisted of methyl methacrylate (MMA), 4-methacryloyloxyethyl trimellitate anhydride (4-META) and tri-n-butylborane (TBB) initiator. The other luting agent (MMA-TBB resin) consisted of MMA and TBB without 4-META. Extracted bovine teeth were ground to expose the dentine, etched with an aqueous solution of 10% phosphoric acid, primed, and then bonded with stainless-steel rods; tensile bond strengths were determined after 1-day immersion in water. Data were analysed by ANOVA and Duncan's new multiple range test (P < 0.05).

RESULTS

Four of the metal chlorides (CuCl2, FeCl3, MgCl2 and ZnCl2) enhanced the bond strengths of MMA-TBB resin to dentine. With Super-Bond resin, maximum bond strengths of 15.6 MPa and 19.0 MPa were recorded with primer containing 2.0 x 10(-5) mol g(-1) FeCl3 and 2.0 x 10(-6) mol g(-1) CuCl2, respectively.

CONCLUSIONS

Bonding techniques, combining the use of either cupric primer or ferric primer with 10% phosphoric acid etchant may be suitable for application in seating resin-bonded prostheses with TBB-initiated luting materials.

Effect of enamel and dentin surface wetness on shear bond strength of composites

PURPOSE

This study investigated the effect of the wetness of human enamel and dentin surfaces on the shear bond strength of composites.

MATERIAL AND METHODS

Seven dentin bonding systems were used. Three methods of preparing the enamel or dentin surface before applying primer or bonding agent were adopted as test conditions: wet (blot dried), semidry (3-second air blast), and dry (15-second air drying). Shear bond strength was measured with a universal testing machine. Mean bond strengths were analyzed with analysis of variance and Scheffe's F-test. Enamel and dentin surfaces were observed by a dissecting microscope after shear bond testing.

RESULTS

Enamel specimens tested by all systems and dentin tested by two systems did not reveal significant differences in shear bond strengths (p > 0.05). Among dentin specimens tested by two systems with water-based primers, the shear bond strength values of the dry technique group were higher than those of the other two groups (p < 0.05). However, among dentin specimens tested by systems having acetone-based primers or bonding agents, bond strength values of the wet or semidry technique groups were higher than those of the dry technique group (p < 0.05).

CONCLUSION

It was concluded that some water might be needed by dentin surfaces or for primers to obtain high bond strength on the dentin surface, but that drying methods did not affect bonding strength to enamel surfaces either before priming or after conditioning.

Adhesive bonding to dentin with ferrous chloride primers and tri-n-butylborane-initiated luting agents

A variety of surface modifications with metal chlorides has been used to enhance the bond of resins to dentin. This study investigated the effectiveness of ferrous chloride in terms of the initiation of polymerization in dentin bonding. The efficacy of experimental dentin primers was evaluated via the bonding of two luting agents to dentin. The 16 primers evaluated were ferrous chloride (FeCl2) aqueous solutions, eight with and eight without 35% 2-hydroxyethyl methacrylate (HEMA). The concentrations of FeCl2 in the primers ranged from 2.0 x 10(-6) to 5.0 x 10(-4) mol/g. One luting agent (Super-Bond C&B) consisted of methyl methacrylate (MMA), 4-methacryloyloxyethyl trimellitate anhydride (4-META), and tri-n-butylborane (TBB) initiator. The other luting agent was prepared with MMA and TBB, but without 4-META. Bovine dentin surfaces were flattened, etched with an aqueous solution of 10% phosphoric acid, primed, and then bonded with stainless steel rods. Tensile strengths of the bonded specimens were measured after one-day immersion in water. Tensile testing revealed that the bond strength was influenced by the application of FeCl2 and/or HEMA. The maximum bond strength of 33.0 MPa was recorded with the use of primer containing FeCl2 and HEMA in MMA-TBB resin. In the case of Super-Bond, only surface treatment of dentin with aqueous primers containing 5.0 x 10(-5) to 2.0 x 10(-4) mol/g ferrous chloride resulted in bond strength values above 22.0 MPa. This bonding technique, combining the use of ferrous chloride primer with Super-Bond resin, may potentially be applied for seating resin-bonded restorations.