The influence of heat treatment on the mechanical properties of Ni-Ti file materials

Phase transformation behavior and mechanical properties of HyFlex EDM nickel-titanium endodontic rotary instrument: Evaluation at body temperature

Background/purpose

Temperature-dependent phase compositional changes influence the mechanical properties of heat-treated nickel-titanium (NiTi) rotary instruments. This study evaluated the phase composition, bending properties, and cyclic fatigue resistance of HyFlex EDM NiTi rotary instruments against differently heat-treated and non-heat-treated NiTi instruments at body temperature (BT).

Materials and methods

HyFlex EDM OneFile (EDM) instruments, heat-treated HyFlex CM (CM) and Twisted File (TF) instruments, and non-heat-treated K3 instruments (size #25/.08) were subjected to differential scanning calorimetry, and the martensitic, R-phase, and reverse transformation starting and finishing temperatures were determined. A cantilever bending test and a cyclic fatigue test were conducted at BT (37 °C ± 1.0 °C), and the bending load and number of cycles to failure (NCF) were recorded. Statistical analysis was performed using Kruskal-Wallis and Mann-Whitney U tests (α = 0.05).

Results

TF and K3 had reverse transformation finishing temperatures lower than BT, while those for EDM and CM were higher than BT. The bending loads at a 0.5 mm deflection were in the order of EDM < TF < CM < K3 (P < 0.05), and those at a 2.0 mm deflection were EDM < CM and TF < K3 (P < 0.05). EDM had the highest NCF among the four instruments (P < 0.05).

Conclusion

The EDM instrument had a reverse transformation finishing temperature higher than BT indicating its martensite/R-phase composition at BT. The EDM instrument had superior flexibility and greater resistance to cyclic fatigue than the CM, TF, and K3 instruments at BT.

Influence of endodontic motors on the behaviour of root canal shaping instruments: an in vitro comparative study

AIMS

The endodontic literature reports a lot of comparative study on endodontic instruments, concerning as well their geometry, instrumental dynamics, material, mechanical behavior or heat treatment. However, to our knowledge, no study has focused on the influence of endodontic motors on the shaping abilities of endodontic instruments. Thus, the aim of this study was to analyze the influence of the endodontic motors on root canal shaping instruments.

METHOD

Dual Move (MICRO-MEGA, Besançon, France), Canal Pro CL2i (COLTENE, Alstätten, Suisse), Canal Pro Jeni Motor (COLTENE, Alstätten, Suisse), Ai Motor (WOODPECKER, Guilin, China), Wave One motor (VDW, Postfach, Munich) and Smart A (WOODPECKER, Guilin, China) were pre-clinically compared in continuous rotation and reciprocating motion on a traction/compression bench using resin blocks. Canal shaping in continuous rotation and reciprocating motion were performed with One Curve and One RECI instruments (MICRO-MEGA, Besançon, France), respectively. The penetration/removal forces, making it possible to objectify the cutting effect and screwing effect of the instruments during root canal shaping, were analyzed.

RESULTS

The results showed (i) that endodontic motors influence the mechanical behavior of endodontic instruments, (ii) that the influence of the motors is essentially felt during reciprocating motion and (iii) that the reciprocating angles influence the mechanical behavior of endodontic instruments.

CONCLUSION

Only endodontic instruments are widely studied in literature while endodontic motors have a direct influence on root canal treatment. This study analyzes the influence of the endodontic motors on root canal shaping instruments. This study tends to demonstrate that Jeni Motor could optimize the mechanical behavior of endodontic instruments.

Dynamic torque and screw-in force of four different glide path instruments assessed in simulated single- and double-curved canals: An in vitro study

Background/purpose

The glide path instruments are the introductory instruments into the canals; thus, they should be durable enough to withstand torsional stress/screw-in force. This study aimed to investigate the torque and screw-in force of TruNatomy Glider (TN), ProGLIDER (PG), Hyflex EDM (EDM) and Dent Craft RE (RE) glide path instruments in single- and double-curved canals.

Materials and methods

Each instrument brand was divided into two groups (n = 7 each) according to the canal configuration. Torque and screw-in force were recorded during automated instrumentation of simulated resin canals with XSmart IQ cordless motor after the canal patency was checked with a #10 K-file. The values were statistically analyzed using the Kolmogorov-Smirnov test followed by the Kruskal Wallis test and the Mann-Whitney U test with Bonferroni correction (α = 0.05).

Results

TN produced significantly higher torque than RE in single-curved canals and PG in double-curved canals (P < 0.05). EDM yielded significantly higher screw-in force than TN and RE in single-curved canals (P < 0.05), but there was no significant difference in double-curved canals (P > 0.05). A significant effect of different canal configurations was only detected for screw-in force in EDM (P < 0.05).

Conclusion

TN in single-curved canals and RE in double-curved canals yielded higher torque values, while EDM exhibited greater screw-in force in both canal configurations. No effect of different canal configurations was detected for torque, but a significant impact was detected for screw-in force in EDM.

Experimental Analysis of the Influence of Heat Treatments on the Flexibility of NiTi Alloy for Endodontic Instruments Manufacturing

The flexibility of NiTi based endodontic files is improved by heat treatment, leading to lower risk of failure, ledges, and canal transportation during the preparation of curved root canals. The aim of this study is to investigate and clearly highlight the influence of every parameter of heat treatment on the flexibility of NiTi wires and thus of endodontic instruments. A full factorial Design of Experiment (DoE) and a designed bending-torsion bench following the ISO 3630-1 standard were used for this investigation. Temperature, holding time, and cooling method were selected as contributing factors, while maximum bending moment, hysteresis size, and stiffness during martensitic transformation were selected as outputs. Regression analysis was performed to estimate the relationship between contributing and output variables to assess how the experimentation fits with the model. The experimental results showed that wires heated at 425 °C for 30 min are more flexible. Moreover, heat treatment temperature is the most critical factor influencing the flexibility and hysteresis size of the NiTi wire followed by the holding time, while the cooling method has a negligible effect. The regression analysis showed that the model is effective at predicting the relationship between contributing factors, bending moment response, and hysteresis size.

Mechanical Properties and Root Canal Shaping Ability of a Nickel-Titanium Rotary System for Minimally Invasive Endodontic Treatment: A Comparative In Vitro Study

Selection of an appropriate nickel−titanium (NiTi) rotary system is important for minimally invasive endodontic treatment, which aims to preserve as much root canal dentin as possible. This study aimed to evaluate selected mechanical properties and the root canal shaping ability of TruNatomy (TRN), a NiTi rotary system designed for minimally invasive endodontic shaping, in comparison with existing instruments: HyFlex EDM (HEDM), ProTaper Next (PTN), and WaveOne Gold (WOG). Load values measured with a cantilever bending test were ranked as TRN < HEDM < WOG < PTN (p < 0.05). A dynamic cyclic fatigue test revealed that the number of cycles to fracture was ranked as HEDM > WOG > TRN > PTN (p < 0.05). Torque and vertical force generated during instrumentation of J-shaped artificial resin canals were measured using an automated instrumentation device connected to a torque and vertical force measuring system; TRN exhibited smaller torque and vertical force values in most comparisons with the other instruments. The canal centering ratio for TRN was smaller than or comparable to that for the other instruments except for WOG at the apex level. Under the present experimental conditions, TRN showed higher flexibility and lower torque and vertical force values than the other instruments.

Comparative evaluation of mechanical properties and shaping performance of heat-treated nickel titanium rotary instruments used in the single-length technique

This study aimed to evaluate the mechanical properties of contemporary heat-treated nickel-titanium (NiTi) rotary instruments used in the single-length technique [ProTaper Next (PTN), HyFlex EDM (EDM), and JIZAI (JZ)]. Bending loads, cyclic fatigue resistance, torque/force values and canal-centering ratios were evaluated for the three instruments and a non-heat-treated experimental NiTi instrument with the same geometry as JZ (nJZ). EDM and JZ exhibited significantly lower bending load and more cycles to failure compared with nJZ and PTN (p<0.05). PTN and JZ exhibited significantly better centering ability than nJZ and EDM (p<0.05). JZ and nJZ generated significantly smaller upward force and maximum torque than PTN and EDM (p<0.05). Under the present experimental condition, JZ exhibited flexibility and cyclic fatigue resistance comparable to EDM, better maintained the canal curvature than the other instruments, and generated smaller torque and screw-in force than PTN and EDM.

Comparison of Torque, Screw-in Force, and Shaping Ability of Glide Path Instruments in Continuous Rotation and Optimum Glide Path Motion

INTRODUCTION

This study aimed to analyze torque/force generation and transportation in double-curved canals instrumented with 3 types of glide path files using optimum glide path (OGP) motion in comparison with continuous rotation.

METHODS

Sixty simulated double-curved canals were prepared with #10/0.05 or #15/0.03 HyFlex EDM Glidepath files (Coltene/Whaledent, Altstätten, Switzerland) or a #13/0.04 prototype MANI Glidepath file (Tochigi, Japan) using OGP motion or continuous rotation (n = 10 each). Canals were sequentially prepared to 20 mm and 22 mm (full working length) using automated root canal instrumentation and a torque/force analyzing device. Transportation was calculated at 1-9 mm from the apex. Data were compared using 2-way analysis of variance followed by a post hoc simple main effect test with Bonferroni correction and a Kruskal-Wallis test (α = 5%).

RESULTS

All #10/0.05 instruments fractured. In the 22-mm preparation, the OGP motion resulted in lower clockwise torque and screw-in force than did continuous rotation (P < .05). In the 20-mm preparation, #15/0.03 instruments recorded a lower screw-in force for OGP motion than for continuous rotation (P < .05). Comparing the 2 preparation phases, OGP motion generated no significant differences; however, continuous rotation developed higher clockwise torque and screw-in force in the 22-mm preparation than in the 20-mm preparation (P < .05). There was no significant difference among the tested groups for transportation values.

CONCLUSIONS

Compared with continuous rotation, OGP motion generated less screw-in force, lower clockwise torque, and similar transportation. The #15/0.03 HyFlex EDM instrument and the #13/0.04 prototype MANI instrument performed similarly well.

Cyclic fatigue resistance of HyFlex EDM, Reciproc Blue, WaveOne Gold, and Twisted File Adaptive rotary files under different temperatures and ambient conditions

Background. This study examined the effects of changes in temperature and environmental conditions on the cyclic fatigue resistance of Reciproc Blue, HyFlex EDM, WaveOne Gold, and Twisted File Adaptive. Methods. Forty-five Reciproc Blue (25/.08), 45 HyFlex EDM (25/.08), 45 WaveOne Gold (25/.07), and 45 Twisted File Adaptive (25/.08) files were tested for cyclic fatigue at room temperature (20°C) in air and water and at body temperature (35°C) in water. All the instruments were rotated in artificial canals made of stainless steel with an inner diameter of 1.5 mm, 60° angle of curvature and a radius of curvature of 5 mm until fracture occurred; the time to fracture was recorded in seconds, using a digital chronometer. Mann-Whitney U test was used for the statistical analysis of data, with SPSS 21.0. Results. Cyclic fatigue resistance was significantly higher in all the groups in water at an ambient temperature of 20°C compared with air and water at temperatures of 20°C and 35°C, respectively (P<0.05). The intragroup analysis revealed that HyFlex EDM had the highest cyclic fatigue resistance, followed by Reciproc Blue, WaveOne Gold, and Twisted File Adaptive in both air and water at 20°C (P<0.05). HyFlex EDM exhibited the highest cyclic fatigue resistance in water at 35°C, whereas there was no significant difference between the other groups (P>0.05). Conclusion. Within the limitations of the present study, an increase in the ambient temperature significantly decreased the cyclic fatigue resistance of the tested NiTi files.

Comparison of cold-hardening bending and direct electric resistance heat treatment on the mechanical properties and transformation temperature of NiTi archwire: An in vitro study

OBJECTIVES

The aim of this investigation was (1) to compare the effects of cold-hardening bending and direct electric resistance heat treatment (DERHT) methods; and (2) to compare the effects of offsets and angulations on the mechanical properties and thermal analysis of NiTi alloy archwire.

METHODS

Nickel-titanium (NiTi) archwires (Ormco, Glendora, CA), 0.016×0.022-inch, were bent by cold-hardening bending and DERHT methods into 1-mm, 2-mm, or 3-mm offset for a 3-point bending test, and at angles of 30°, 45°, or 60° to the horizontal plane for testing the change in transformation temperature (A_f) measured by differential scanning calorimetry (DSC). The data were analysed using ANOVA followed by the Scheffe post-hoc test.

RESULTS

The 3-point bending test results of the cold-hardening bending and DERHT methods were not significantly different between the 1-mm, 2-mm and 3-mm offset groups (95% CI: -0.05 to 0.97; P=0.082, 95% CI: -0.65 to 0.74; P=0.983 and 95% CI: -0.61 to 0.98; P=0.813, respectively). Increasing the offset resulted in a significantly decreased force in the 3-point bending test (P<0.001). The A_f temperatures of the cold-hardening bending and DERHT methods were not significantly different for the 30°, 45°, and 60° bending angulations (95% CI: -1.93 to 1.39; P=0.876, 95% CI: -1.2 to 0.87; P=0.878, 95% CI: -2.24 to 1.18; P=0.636, respectively). A_f temperatures were not influenced by different bending angulations.

CONCLUSIONS

NiTi archwire shape can be modified by using both cold-hardening and DERHT bending methods, because the mechanical properties and A_f temperature are not affected. However, the bending distance has an effect on the mechanical properties.