Three-dimensional finite element analysis of implant-supported crown in fibula bone model

Mechanical property of Ti6Al4V cylindrical porous structure for dental implants fabricated by selective laser melting

The commonly used titanium alloy dental implants currently apply solid structures. However, issues such as stress shielding and stress concentration may arise due to the significant difference in elastic modulus between the implant and host. In order to address these problems, this paper proposes five porous structures based on the Gibson-Ashby theoretical model. We utilized selective laser melting technology to shape a porous structure using Ti-6Al-4V material precisely. The mechanical properties of the porous structure were verified through simulation and compression experiments. The optimal porous structure, which best matched the human bone, was a circular ring structure with a pillar diameter of 0.6 mm and a layer height of 2 mm. The stress and strain of the porous implant on the surrounding cortical and cancellous bone under different biting conditions were studied to verify the effectiveness of the optimal circular ring porous structure in alleviating stress shielding in both standard and osteoporotic bone conditions. The results confirm that the circular ring porous structure meets implant requirements and provides a theoretical basis for clinical dental implantation.

The Development and Biomechanical Analysis of an Allograft Interference Screw for Anterior Cruciate Ligament Reconstruction

Graft fixation during cruciate ligament reconstruction using interference screws is a common and frequently used surgical technique. These interference screws are usually made of metal or bioabsorbable materials. This paper describes the development of an allograft interference screw from cortical human bone. During the design of the screw, particular attention was paid to the choice of the screw drive and the screw shape, as well as the thread shape. Based on these parameters, a prototype was designed and manufactured. Subsequently, the first biomechanical tests using a bovine model were performed. The test procedure comprised a torsion test to determine the ultimate failure torque of the screw and the insertion torque during graft fixation, as well as a pull-out test to asses the ultimate failure load of the graft fixation. The results of the biomechanical analysis showed that the mean value of the ultimate failure torque was 2633 Nmm, whereas the mean occurring insertion torque during graft fixation was only 1125 Nmm. The mean ultimate failure load of the graft fixation was approximately 235 N. The results of this work show a good overall performance of the allograft screw compared to conventional screws, and should serve as a starting point for further detailed investigations and studies.

A comparison of stress, contact pressure, and contact area on menisci in re-injury mechanisms after reconstruction of the anterior cruciate ligament with autograft and synthetic graft: a finite element study

PURPOSE

The anterior cruciate ligament (ACL) is crucial in maintaining knee stability. Some motion mechanisms, which are common in sports, cause excessive load to be passed on the ACL. In non-contact ACL injuries, the ACL cannot sustain the high stress and becomes injured or ruptures in the valgus-external rotation mechanism (VERM) and varus-internal rotation mechanism (VIRM). The mechanical strength of the grafts used to repair the torn ligament varies. The purpose of this study is to look at the alterations in the menisci after anterior cruciate ligament repair with autografts and synthetic grafts in cases of non-contact re-injury mechanisms.

METHODS

In the finite element analysis, VERM and VIRM motions of the injury were simulated with different ACL graft materials. During the simulations of these mechanism motions with polyethylene terephthalate (PET) and patellar tendon (PT), the contact pressures, contact areas, and von mises stress values created in the medial and lateral meniscus were compared.

RESULTS

The peak contact pressures on the menisci during the VERM are higher than the peak contact pressures during the VIRM, except for one variation. The peak contact pressure of the medial meniscus is almost the same for both graft materials and mechanisms. Furthermore, the peak contact pressures in the menisci are higher than in the VERM. For all injury mechanisms, the peak contact stresses on the lateral meniscus are higher than on the medial meniscus.

CONCLUSIONS

The findings suggest that VERM can induce further knee joint injury. It was found that the PET will lessen the pressure on the menisci even more. It is also advantageous since it does not damage the anterior extremities and transmits less pressure to the menisci. In conclusion, using a high-strength ACL is healthier for the menisci. Even though synthetic grafts are not clinically preferred, the study demonstrates that enhancing the material properties of synthetic grafts will increase the chance of their use in the future, based on the current results.

The evaluation of stress on bone level and tissue level short implants: A Finite Element Analysis (FEA) study

PURPOSE

This study aimed to evaluate the difference between the stress level and distribution around the BL and TL short implants, and their surrounding structures, using finite element analysis.

METHODS

Two different study models were constructed: BL model and TL model. Two dental implant systems (ITI (Straumann, Waldenburg, Switzerland) and NTA Short) with a diameter of 4.1 mm and 4 mm and with a length of 6 mm were used in this study. In each model, implants were placed in the mandibular 1st molar region. The von Mises stress and maximum principal (tensile) and minimum principal (compressive) stresses were evaluated.

RESULTS

The highest stress values recorded in the BL implants (von Mises: 342.77 MPa), in the peri‑implant bone around the BL implants (maximum principal stress: 114.1 MPa), as a result of oblique loading, and overall stress values were found to be higher in the BL model. However, these measured values appeared to be low to cause a fracture, when considering the yield strengths of the materials and bone.

CONCLUSIONS

The stress values were higher in the BL model, but not high enough to cause failure. Short implants could be an effective method of treatment for patients unsuitable for advanced surgical techniques.

A Novel Screw Drive for Allogenic Headless Position Screws for Use in Osteosynthesis-A Finite-Element Analysis

Due to their osteoconductive properties, allogenic bone screws made of human cortical bone have advantages regarding rehabilitation compared to other materials such as stainless steel or titanium. Since conventional screw drives like hexagonal or hexalobular drives are difficult to manufacture in headless allogenic screws, an easy-to-manufacture screw drive is needed. In this paper, we present a simple drive for headless allogenic bone screws that allows the screw to be fully inserted. Since the screw drive is completely internal, no threads are removed. In order to prove the mechanical strength, we performed simulations of the new drive using the Finite-Element method (FEM), validated the simulations with a prototype screw, tested the novel screw drive experimentally and compared the simulations with conventional drives. The validation with the prototype showed that our simulations provided valid results. Furthermore, the simulations of the new screw drive showed good performance in terms of mechanical strength in allogenic screws compared to conventional screw drives. The presented screw drive is simple and easy to manufacture and is therefore suitable for headless allogenic bone screws where conventional drives are difficult to manufacture.

Influence of transmucosal height in abutments of single and multiple implant-supported prostheses: a non-linear three-dimensional finite element analysis

The aim of this study was to analyze the influence of three different transmucosal heights of the abutments in single and multiple implant-supported prostheses through the finite element method. External hexagon implants, MicroUnit, and EsthetiCone abutments were scanned and placed in an edentulous maxillary model obtained from a tomography database. The simulations were divided into two groups: (1) one implant with 3.75 × 10 mm placed in the upper central incisor, simulating a single implant-supported fixed prosthesis with an EsthetiCone abutment; and (2) two implants with 3.75 × 10 mm placed in the upper lateral incisors with MicroUnit abutments, simulating a multiple implant-supported prosthesis. Subsequently, each group was subdivided into three models according to the transmucosal height (1, 2, and 3 mm). A static oblique load at an angle of 45 degrees to the long axis of the implant in palatal-buccal direction of 150 and 75 N was applied for multiple and single implant-supported prosthesis, respectively. The implants and abutments were assessed according to the equivalent Von Mises stress analyses while the bone and ceramics were analyzed through maximum and minimum principal stresses. The total deformation values increased in all models, while the transmucosal height was augmented. The transmucosal height of the abutments influences the stress values at the bone, ceramics, implants, and abutments of both the single and multiple implant-supported prostheses, with the transmucosal height of 1 mm showing the lowest stress values.