A three-dimensional finite element analysis of the relationship between masticatory performance and skeletal malocclusion

Evaluation and comparison of three-dimensional finite element analysis of stress distribution in immediately placed and loaded conventional and customized three-dimensional printed dental implants

Aim

The aim of this study was to evaluate and compare the stress distribution patterns in immediately placed and loaded conventional and customized three-dimensional (3D) printed dental implants by 3D finite element analysis.

Materials and Methods

Twelve 3D finite element models [Group A-3 models; Group B-9 models] with 72 test conditions which were modeled and compared from customized 3D printed dental implants [Group A] and 3 commercially available implant systems [Group B] (Straumann, Ankylos, and Astratech) using "SolidWorks". All models were embedded in extraction socket models of the maxillary central incisor (CI) and Canine (C), Mandibular 1st Premolar. An occlusal loading by axial and nonaxial force of 100 N and 150 N at 30° and 45° was applied on the abutment using the "ANSYS" Suite. Customized 3D printed dental implant (Group A) for maxilla (Max.) CI, Max. C, and mandibular 1st premolar (PM) socket model was compared with three commercial available dental implant systems (Group B) for Max. CI, Max. C, and mandible (Mand.) 1st PM socket model to understand the stress distribution patterns.

Results

With increasing oblique loads, von Mises stresses were reduced for the customized group as compared to conventional implants. Increased axial loads caused proportionate increase in the stresses for both groups, yet remained under the physiologic limits in all test conditions. Higher stresses were observed in cortical bone than in cancellous bone at bone-implant contact in general. Marked reduction in von Mises stress was observed at the boundary between compact and cancellous bone. Customized 3D printed implants performed better for oblique loads and comparable for axial load stress distribution in comparison to conventional implant systems in Max. CI and C, Mand. 1st PM.

Conclusion

Thus, customized 3D printed implants appear a promising alternative for immediately placed immediately loaded protocols, with additional benefits in specific clinical situations.

Finite element analysis of various thickness occlusal stabilization splint therapy on unilateral temporomandibular joint anterior disc displacement without reduction

INTRODUCTION

Occlusal stabilization splint is the most common treatment modality for temporomandibular joint disorders, but the optimal thickness is still uncertain. This study investigated the effect of the occlusal splint with different thicknesses on the stress distribution of the temporomandibular joint.

METHODS

Cone-beam computed tomography and magnetic resonance images were used to reconstruct the maxillofacial and disc, and the unilateral anterior disc displacement without reduction was established manually as the basic model. Occlusal splint with 5 different thickness levels (2, 3, 4, 5, and 6 mm) was added to the basic model as the study models. The displacement and stress distribution of the disc were evaluated.

RESULTS

The maximum von Mises stress of the condylar cartilage was the largest on the affected side, whereas the maximum von Mises stress of the disc was the largest on the unaffected side. The disc stress on the affected side was mainly distributed on the posterior zone and the intermediate zone for the unaffected side. The maximum von Mises stress of the bilaminar region on the affected side was greater than the unaffected side. The stress of the disc and bilaminar region was the lowest on the affected side in the 2 mm model. The disc displacement on the affected side gradually increased, whereas, on the unaffected side, it fluctuated.

CONCLUSIONS

These results showed that occlusal stabilization splint could decrease the stress of disc and bilaminar region, and 2 mm was considered the optimal thickness for the treatment of unilateral temporomandibular joint anterior disc displacement without reduction.

First molar health status in different craniofacial relationships

Objective

To investigate the association between the health status of permanent first molars and different craniofacial relationships among adolescents.

Study design

This is a retrospective study on patients’ records aged 11–15 years. Sex, skeletal relationship, vertical growth pattern, malocclusion, overjet, and overbite were assessed. The health status of permanent first molars was recorded from the orthopantomograms and intraoral photographs as “sound” and “not sound”. Chi-square, Mann–Whitney U and Kruskal–Wallis tests, and Pearson’s correlation coefficient were used to analyze and correlate the assessed variables. Significance level was set at P<0.05.

Results

A total of 210 records were evaluated; 81 were male, 68 had Class I and 91 had Class II skeletal relationships. More than half of the subjects had normal (n=67) to moderate deep bite (n=72); normal (n=91), moderately increased (n=54), to severely increased (n=50) overjet; and Class I (n=106) and Class II division 1 (n=75) malocclusion. Significant differences were found in the health status of the permanent first molars with respect to sex (P=0.034), vertical growth pattern (P=0.01), and overbite (P=0.047). Strong correlations were only found between the health status of the permanent first molars and the following variables: sex (P=0.036) and vertical growth pattern (P=0.004). Significant correlation was further found between the upper left first molar health status and sex (P=0.019) and the lower right first molar health status and the vertical growth pattern (P=0.001). No significant association was found with the anteroposterior craniofacial relationships (P>0.05).

Conclusion

Sex difference and vertical growth patterns were found to be potential predictors of the health status of the permanent first molars. No significant association was found with the anteroposterior craniofacial relationships.

Dynamic Modelling of Tooth Deformation Using Occlusal Kinematics and Finite Element Analysis

Background

Dental biomechanics based on finite element (FE) analysis is attracting enormous interest in dentistry, biology, anthropology and palaeontology. Nonetheless, several shortcomings in FE modeling exist, mainly due to unrealistic loading conditions. In this contribution we used kinematics information recorded in a virtual environment derived from occlusal contact detection between high resolution models of an upper and lower human first molar pair (M¹ and M₁, respectively) to run a non-linear dynamic FE crash colliding test.

Methodology

MicroCT image data of a modern human skull were segmented to reconstruct digital models of the antagonistic right M¹ and M₁ and the dental supporting structures. We used the Occlusal Fingerprint Analyser software to reconstruct the individual occlusal pathway trajectory during the power stroke of the chewing cycle, which was applied in a FE simulation to guide the M₁ 3D-path for the crash colliding test.

Results

FE analysis results showed that the stress pattern changes considerably during the power stroke, demonstrating that knowledge about chewing kinematics in conjunction with a morphologically detailed FE model is crucial for understanding tooth form and function under physiological conditions.

Conclusions/Significance

Results from such advanced dynamic approaches will be applicable to evaluate and avoid mechanical failure in prosthodontics/endodontic treatments, and to test material behavior for modern tooth restoration in dentistry. This approach will also allow us to improve our knowledge in chewing-related biomechanics for functional diagnosis and therapy, and it will help paleoanthropologists to illuminate dental adaptive processes and morphological modifications in human evolution.