A pilot finite element study of an osteoporotic L1-vertebra compared to one with normal T-score

In this paper, two patient-specific finite element (FE) models of both an L1 vertebra with a normal T-score and a mildly wedging, osteoporotic one were created and analysed under usual action. Utilising commercial software packages for image processing and FE analysis (FEA) along with in house computer codes for a posteriori assignment of material properties, in vivo high-resolution spiral computed tomography of the entire vertebrae and FEA were combined. Using the vertebra with a normal T-score as baseline it was found that the maximum value of the von Mises stress in the osteoporotic vertebra was 60% higher but still far below bone strength, while the maximum value of von Mises strain in the same vertebra was 148% higher than that of the vertebra with normal T-score. In the vertebra with normal T-score, 17% of its volume exhibited values of von Mises strain higher than the threshold of 4500 μstrains, referenced by Homminga et al. as a threshold of fracture risk, while in the osteoporotic one this percentage was raised up to 37%. The results suggested that the osteoporotic vertebra is susceptible to fracture due to raised strains and not stresses.

The effect of select pulp cavity conditions on stress field development in distal abutments in two types of fixed dental prostheses

PURPOSE

Insufficient coronal tooth structure may require restoration of endodontically treated (ET) teeth with cast posts and cores (CPCs). The prognosis for these teeth is a matter of scientific debate, especially if they serve as distal abutments in cantilever fixed dental prostheses (FDPs). The purpose of this study was to study stress field development in distal abutments in two types of FDPs with different pulp cavity conditions.

MATERIALS AND METHODS

The methodology involved the development of four digital models in which the right mandibular premolars were splinted via an FDP with: (1) no cantilever and a vital distal abutment, (2) no cantilever and an ET CPC distal abutment, (3) a single-unit cantilever and a vital distal abutment, and (4) a single-unit cantilever with an ET CPC distal abutment. The models were analyzed using a three-dimensional finite element program, and von Mises stress values and patterns were evaluated.

RESULTS

The results revealed that although the stress distribution patterns in dentin were dissimilar, the von Mises stress values registered for the vital and ET CPC distal abutment were not considerably different. However, higher stress values were detected in the dentin area surrounding the post-gutta-percha interface after CPC placement. The addition of the cantilever resulted in a considerable increase in stress on the dental tissue structures.

CONCLUSIONS

CPCs appear to create a risk of potential fracture that is initiated in the dentin at the apex of the post. The type of restoration appears to have a much more serious impact on the stress pattern developed in the distal abutment, and the addition of a cantilever appears to biomechanically compromise both biologic and restorative structures.

On the FEM modeling of craniofacial changes during rapid maxillary expansion

This paper discusses several aspects related to the development of a reliable finite element model to simulate the craniofacial changes during rapid maxillary expansion treatment. The mechanical model concerns the entire human skull (bony structure and sutures) as well as the jackscrew device; the latter transforms the manual openings into orthodontic forces usually applied to the two maxillary halves through the first premolars and first permanent molars, which are the support points of the appliance. A sensitivity analysis of an approximate finite element model is performed in order to investigate the influence of the model size, the influence of the degree of sutural ossification by assigning different mechanical properties to the sutures and the influence of bone relaxation concerning the effects of dentofacial orthopaedics. Moreover, a more accurate model including the aforementioned teeth and their periodontal ligament as solid elastic structures was analysed in order to evaluate the orthodontic effects induced. Results refer to the opening pattern and associated stresses/displacements/strains on the cranium, the maxillae and the periodontal ligament.

In vitro validated finite element method model for a human skull and related craniofacial effects during rapid maxillary expansion

This paper presents the biomechanical effects on the craniofacial complex during rapid maxillary expansions (RME), by using an in vitro experiment compared with a three-dimensional (3D) finite element model of a human skull. For this purpose, a dry human skull with artificially constructed teeth was used. In addition, a 3D finite element model including the craniofacial sutures was developed based on computed tomography (CT) scans. Initially, two types of models were analysed. In the first model, the total activation of the jackscrew device was applied in one step. In the second model, more steps were applied, taking into account the phenomenon of stress relaxation during RME treatment. Afterwards, a parametric analysis of the finite element method model was performed using three more models in order to evaluate the influence of craniofacial sutures. Both in vitro and finite element results refer to the openings of four critical points (MI, UM, EM, and CN) on the left and right maxilla. Results show that the maxillae open in a pyramidal shape and that the degree of sutures ossification influences the displacement distribution on the craniofacial complex much more than the phenomenon of stress relaxation. The areas of the maximum stresses and displacements were also determined.