Cardiovascular stent design and vessel stresses: a finite element analysis

Intravascular stents of various designs are currently in use to restore patency in atherosclerotic coronary arteries and it has been found that different stents have different in-stent restenosis rates. It has been hypothesized that the level of vascular injury caused to a vessel by a stent determines the level of restenosis. Computational studies may be used to investigate the mechanical behaviour of stents and to determine the biomechanical interaction between the stent and the artery in a stenting procedure. In this paper, we test the hypothesis that two different stent designs will provoke different levels of stress within an atherosclerotic artery and hence cause different levels of vascular injury. The stents analysed using the finite-element method were the S7 (Medtronic AVE) and the NIR (Boston Scientific) stent designs. An analysis of the arterial wall stresses in the stented arteries indicates that the modular S7 stent design causes lower stress to an atherosclerotic vessel with a localized stenotic lesion compared to the slotted tube NIR design. These results correlate with observed clinical restenosis rates, which have found higher restenosis rates in the NIR compared with the S7 stent design. Therefore, the testing methodology outlined here is proposed as a pre-clinical testing tool, which could be used to compare and contrast existing stent designs and to develop novel stent designs.

The effects of pupil size on the multifocal electroretinogram

This is an investigation of the effect of changing the pupil diameter on the P1 amplitude and latency of the multifocal electroretinogram (mfERG). MfERGs were recorded using a custom built wide field electrophysiological system. An array of 61 empirically scaled hexagons was used to stimulate the visual field. The duration of overall recording period was 8 min, segmented into 16 intervals each lasting 30 s. A combination of mydriatics and miotics were used to pharmacologically alter the pupil size and diameters between 1 and 10 mm were measured. There was a reduction in mfERG P1 amplitude in some cases greater than 50% (mfERG P1 amplitude 53 nV at 8 mm to 25 nV at 1 mm), with a change in pupil diameter of 7 mm. The mfERG P1 latency increased in some cases by as much as 8 ms in the central 40 degrees (mfERG P1 latency 39 ms at 8 mm to 47 ms at 1 mm). These results suggest that pupil size has significant effects on mfERG P1 amplitude and latency.

Macrophage responses to vascular stent coatings

Diamond-like carbon (DLC) films have been proposed as potential coatings for blood-contacting devices. In this study, tetrahedral amorphous carbon (ta-C) films deposited by filtered cathodic vacuum arc system (FCVA) were compared with commercially deposited polyurethane coatings (PU) and uncoated stainless steel samples. X-ray reflectivity (XRR) measurements were performed to check density and thickness of the ta-C coatings, and contact angles measurements were used to assess surface wettability. J774 macrophages were used to assess the cell responses to the materials. Cell number, metabolic activity, and hydrogen peroxide production were measured by using biochemical assays, and the cell attachment and morphology were determined by using scanning electron microscopy and confocal laser scanning microscopy. Wettability measurements showed that of the materials, the stainless steel was the most hydrophilic, and the ta-C coatings were the most hydrophobic. Although the initial attachment and morphology did not appear to be dependent on the wettability, the cell numbers did increase with increasing wettability. Macrophages on the stainless steel samples were the most active in producing hydrogen peroxide. These data show that ta-C samples performed as well as commercial PU-coated samples in blocking cell reactions to the substrate and may prove to be effective coatings for blood-contacting materials.

Analysis of Prolapse in Cardiovascular Stents: A Constitutive Equation for Vascular Tissue and Finite-Element Modelling

The effectiveness of a cardiovascular stent depends on many factors, such as its ability to sustain the compression applied by the vessel wall, minimal longitudinal contraction when it is expanded, and its ability to flex when navigating tortuous blood vessels. The long-term reaction of the tissue to the stent is also device dependant; in particular some designs provoke in-stent restenosis (i.e., regrowth of the occlusion around the stent). The mechanism of restenosis is thought to involve injury or damage to the vessel wall due to the high stresses generated around the stent when it expands. Because of this, the deflection of the tissue between the struts of the stent (called prolapse or “draping”) has been used as a measure of the potential of a stent to cause restenosis. In this paper, uniaxial and biaxial experiments on human femoral artery and porcine aortic vascular tissue are used to develop a hyperelastic constitutive model of vascular tissue suitable for implementation in finite-element analysis. To analyze prolapse, four stent designs (BeStent 2, Medtronic AVE; NIROYAL, Boston Scientific; VELOCITY, Cordis; TETRA, Guidant) were expanded in vitro to determine their repeating-unit dimensions. This geometric data was used to generate a finite element model of the vascular tissue supported within a repeating-unit of the stent. Under a pressure of 450 mm Hg (representing the radial compression of the vessel wall), maximum radial deflection of 0.253 mm, 0.279 mm, 0.348 mm and 0.48 mm were calculated for each of the four stents. Stresses in the vascular wall were highest for the VELOCITY stent. The method is proposed as a way to compare stents relative to their potential for restenosis and as a basis for a biomechanical design of a stent repeating-unit that would minimize restenosis.