Comparison of the performance characteristics of two tubular contactless conductivity detectors with different dimensions and application in conjunction with HPLC

Two tubular capacitively coupled contactless conductivity detection (C(4)D) cells with different geometric dimensions were evaluated with regard to their main analytical characteristics under non-separation and separation conditions in conjunction with liquid chromatography. A comparison of the performance of the tubular cells to a previously tested thin-layer detection cell was drawn. Additionally, using a theoretical model the experimental results were compared with sets of calculated values and partially enabled to model the complex behavior of C(4)D detection in combination with high-performance liquid chromatography (HPLC). While cell 1 is characterized by a geometric cell volume of 0.6 μL, a wall thickness of 675 μm, and an inner diameter of 125 μm, the respective values for cell 2 are 2.3 μL, 200 μm, and 250 μm. The main analytical parameters were evaluated using a potassium chloride (KCl) solution. The limits of detection were 0.4 μM KCl (5.7 × 10(-6) S m(-1)) for cell 1 and 0.2 μM KCl (3.2 × 10(-6) S m(-1)) for cell 2, which compares well to the previously found 0.2 μM for the thin-layer cell. A pair of linear ranges was found for both cells in a concentration interval ranging from 1 × 10(-6) to 1 × 10(-4) M (corresponding to 1.5 × 10(-5) to 1.5 × 10(-3) S m(-1)) KCl, respectively. Furthermore, the detector cells were applied to the HPLC separation of a model compound system consisting of benzoic acid, lactic acid, octanesulphonic acid, and sodium capronate. Separation of the compounds was achieved with a Biospher PSI 100 C18 column using 60% aqueous acetonitrile mobile phase. Calibration curves for the examined model system were well correlated (r² > 0.997), and it was found that under separation conditions the arrangement with the lower cell volume (cell 1) yields higher sensitivity and respectively lower limits of detection for all model compounds. Compared with the thin-layer cell, the tubular cells show better overall performance in regard to the determined analytical characteristics.

Determination of 1-methylhistidine and 3-methylhistidine by capillary and chip electrophoresis with contactless conductivity detection

CE with capacitively coupled contactless detection (C4D) was used to determine 3-methylhistidine (3-MH) and 1-methylhistidine (1-MH). The C4D response to 3-MH was studied in a BGE consisting of 500 mM acetic acid and ammonia at varying concentration and the results were compared with the theory. Complete separation of a model mixture of 3-MH, 1-MH, and histidine (His) was attained in two optimized BGEs, one containing 500 mM HAc, 20 mM NH4OH, and 0.1 % m/v hydroxyethylcellulose (HEC), pH 3.4 (I) and the other consisting of 100 mM morpholinoethanesulfonic acid (MES), 25 mM LiOH, and 0.1 % m/v HEC, pH 5.5 (II). These optimized BGEs were tested in CE/C4D analyses of urine. Promising results were obtained for separation and determination of 3-MH, 1-MH, and His on a silicon microchip, using aluminum strips as the C4D electrodes; the three analytes were baseline-separated within less than 30 s with a separation channel effective length of 38 mm. The LOD were satisfactory and amounted to 26.4 microM for 3-MH and 18.3 microM for 1-MH.

A contactless conductivity detector for capillary electrophoresis: effects of the detection cell geometry on the detector performance

The effect of the gap between the electrodes and of their width on the behavior of a capacitively wired contactless conductivity detector was studied. The results obtained have indicated that the detector response can be qualitatively described by a model based on the concept of the effective electrode width which is a complex parameter determined by the gap between the electrodes, the frequency of the input signal and the conductivity of the test solution. The detector sensitivity and the effect on the separation efficiency depend on the difference between the effective and geometric electrode widths. Higher detection sensitivities have been attained for detectors with wide electrodes operating at lower frequencies, however, better separation efficiencies have been achieved using detectors with narrow electrodes and higher operational frequencies. The noise increases with decreasing gap between the electrodes and increasing frequency, especially with detectors employing narrow electrodes.

A chip-based capillary electrophoresis-contactless conductivity microsystem for fast measurements of low-explosive ionic components

A miniaturized analytical system for separating and detecting inorganic explosive residues, based on the coupling of a micromachined capillary electrophoresis (CE) chip with a contactless conductivity detector is described. The low electroosmotic flow (EOF) of the poly(methylmethacrylate) (PMMA) chip material facilitates the rapid switching between analyses of cations and anions using the same microchannel and run buffer (and without an EOF modifier), and hence offers rapid (< 1 min) measurement of seven explosive-related cations and anions. Experimental parameters relevant to the separation and detection processes have been optimized. Addition of a 18-crown-6 ether modifier has been used for separating the peaks of co-migrating potassium and ammonium ions. The ionic-explosive microchip system combines the distinct advantages of contactless conductivity detection with the attractive features of plastic CE microchips. The new microsystem offers great promise for monitoring explosive-related ions at the sample source, with significant advantages of speed/warning, efficiency, cost, or sample size.

Contactless conductivity detector for microchip capillary electrophoresis

A microfabricated electrophoresis chip with an integrated contactless conductivity detection system is described. The new contactless conductivity microchip detector is based on placing two planar sensing aluminum film electrodes on the outer side of a poly(methyl methacrylate) (PMMA) microchip (without contacting the solution) and measuring the impedance of the solution in the separation channel. The contactless route obviates problems (e.g., fouling, unwanted reactions) associated with the electrode-solution contact, offers isolation of the detection system from high separation fields, does not compromise the separation efficiency, and greatly simplifies the detector fabrication. Relevant experimental variables, such as the frequency and amplitude of the applied ac voltage or the separation voltage, were examined and optimized. The detector performance was illustrated by the separation of potassium, sodium, barium, and lithium cations and the chloride, sulfate, fluoride, acetate, and phosphate anions. The response was linear (over the 20 microM-7 mM range) and reproducible (RSD = 3.4-4.9%; n = 10), with detection limits of 2.8 and 6.4 microM (for potassium and chloride, respectively). The advantages associated with the contactless conductivity detection, along with the low cost of the integrated PMMA chip/detection system, should enhance the power and scope of microfluidic analytical devices.

Split-flow injector for capillary zone electrophoresis

A simple construction of a split-flow injector eliminating some common problems connected with the use of such devices is described. It consists of a low-pressure pump, an injection valve and a delivery tube in which the separating capillary inlet is fixed. The sample is injected without moving the separating capillary inlet and without interrupting the applied voltage. The grounded electrophoretic electrode is close to the injection valve so that all metal parts of the injector are kept at a sufficiently low potential. Minimum length and small internal diameter of delivery tube minimizes additional sample zone broadening. The effects of some experimental parameters, such as the position of the separation capillary inlet with respect to the background solution flow direction and background solution flow-rate are experimentally studied. The injector was tested primarily for the electrokinetic injection.