Low-cost, 3D printed irradiation system for in vitro photodynamic therapy experiments

The development of a suitable irradiation setup is essential for in vitro experiments in photodynamic therapy (PDT). While various irradiation systems have been developed for PDT, only a few offer practical and high-quality setups for precise and reproducible results in cell culture experiments. This report introduces a cost-effective illumination setup designed for in vitro photodynamic treatments. The setup consists of a commercially available light-emitting diode (LED) lamp, a cooling unit, and a specially designed 3D-printed enclosure to accommodate a multiwell plate insert. The LED lamp is versatile, supporting various irradiation wavelengths and adjustable illumination fields, ensuring consistent and reliable performance. The study evaluates the setup through various parameters, including photon flux density, illumination uniformity, photon distribution across the multiwell plate, and temperature changes during irradiation. In addition, the effectiveness of the LED-based illumination system is tested by treating mouse mammary breast carcinoma cells (4T1) with Rose Bengal and LED irradiation at around 525 nm. The resulting IC50 of 5.2 ± 0.9 μM and a minimum media temperature change of ca. 1.2°C indicate a highly promising LED-based setup that offers a cost-effective and technically feasible solution for achieving consistent, reproducible, and uniform irradiation, enhancing research capabilities and potential applications.

Stabilizing Ni2+ in Hollow Nano MOF/Polymetallic Phosphides Composites for Enhanced Electrochemical Performance in 3D-Printed Micro-Supercapacitors

Polymetallic phosphides exhibit favorable conductivities. A reasonable design of nano-metal-organic frame (MOF) composite morphologies and in situ introduction of polymetallic phosphides into the framework can effectively improve electrolyte penetration and rapid electron transfer. To address existing challenges, Ni, with a strong coordination ability with N, is introduced to partially replace Co in nano-Co-MOF composite. The hollow nanostructure is stabilized through CoNi bimetallic coordination and low-temperature controllable polymetallic phosphide generation rate. The Ni, Co, and P atoms, generated during reduction, effectively enhance electron transfer rate within the framework. X-ray absorption fine structure (XAFS) characterization results further confirm the existence of Ni-N, Ni-Ni, and Co-Co structures in the nanocomposite. The changes in each component during the charge-discharge process of the electrochemical reactions are investigated using in situ X-ray diffraction (XRD). Theoretical calculations further confirm that P can effectively improve conductivity. VZNPGC//MXene MSCs, constructed with active materials derived from the hollow nano MOF composites synthesized through the Ni2+ stabilization strategy, demonstrate a specific capacitance of 1184 mF cm-2, along with an energy density of 236.75 µWh cm-2 (power density of 0.14 mW cm-2). This approach introduces a new direction for the synthesis of highly conductive nano-MOF composites.

Validation of a 3D-printed robot-assisted partial nephrectomy training model

Objectives

Most renal tumours can be treated with a partial nephrectomy, with robot-assisted partial nephrectomy becoming the new gold standard. This procedure is challenging to learn in a live setting, especially the enucleation and renorraphy phases. In this study, we attempted to evaluate face, content, and preliminary construct validity of a 3D-printed silicone renal tumour model in robotic training for robot-assisted partial nephrectomy.

Materials and Methods

We compared the operative results of three groups of surgeons with different experience levels (>20 partial nephrectomies, 1-20 partial nephrectomies and no experience at all) performing a robotic tumour excision of a newly developed silicone model with four embedded 3D-printed renal tumours. We evaluated the participants' performance using surgical margins, excision time, total preserved parenchyma, tumour injury and GEARS score (as assessed by two blinded experts) for construct validity. Postoperatively, the participants were asked to complete a survey to evaluate the usefulness, realism and difficulty of the model as a training and/or evaluation model. NASA-TLX scores were used to evaluate the operative workload.

Results

Thirty-six participants were recruited, each group consisting of 10-14 participants. The operative performance was significantly better in the expert group as compared to the beginner group. NASA-TLX scores proved the model to be of an acceptable difficulty level.Expert group survey results showed an average score of 6.3/10 on realism of the model, 8.2/10 on the usefulness as training model and 6.9/10 score on the usefulness as an evaluation tool. GEARS scores showed a non-significant tendency to improve between trials, emphasizing its potential as a training model.

Conclusion

Face and content validity of our 3D renal tumour model were demonstrated. The vast majority of participants found the model realistic and useful for training and for evaluation. To evaluate construct and predictive validity, we require further research, aiming to compare the results of 3D-model trained surgeons with those of untrained surgeons in real-life surgery.