Relation between internal adaptation and degree of conversion of short-fiber reinforced resin composites applied in bulk or layered technique in deep MOD cavities

OBJECTIVE

The purpose was to evaluate the degree of conversion (DC), internal adaptation (IA) and closed porosity (CP) of short-fiber reinforced resin composites (SFRC) associated with layered or bulk restorative procedures in deep MOD cavities.

METHODS

Eighty third molars with standardized MOD cavities (5-mm-depth, 2.5-mm-width) were randomly divided into four groups and restored as follows: 1) bulk SFRC; 2) layered SFRC; 3) flowable bulk-fill resin-based composites (RBC); 4) layered conventional RBC. After one-month wet storage the samples were subjected to micro-computed tomography measurements and scanning electron microscopy to assess the IA and CP. Micro-Raman spectroscopy was used to determine the DC in different depths. Data were subjected to ANOVA and Tukey's post-hoc test, multivariate analysis and partial eta-squared statistics (p < 0.05). Pearson correlation coefficient was determined to assess the relationship among the parameters of interest.

RESULTS

Gap/total interface volume ratio ranged between 0.22-0.47%. RBCs applied in bulk revealed significantly lower gap volume (p < 0.001) and CP (p < 0.05). Each group showed complete detachment on the pulpal and partial on the lateral walls, except for group3. While the highest DC% was achieved by the conventional RBC (87.2%), followed by the flowable bulk-fill (81.2%), SFRC provided the best bottom to top DC ratio (bulk: 96.4%, layered: 98.7%). The effect of factors studied (RBC type, filling technique) on IA and DC was significant (p < 0.001).

SIGNIFICANCE

Bulk placement of RBCs exhibited lower interfacial gap volume and achieved satisfactory DC without significant correlation between these parameters. Incremental insertion of SFRC had no advantage over bulk placement in terms of IA and DC.

Short fiber-reinforced resin-based composites (SFRCs); Current status and future perspectives

One technique for placing of resin-based composite for large posterior cavities is the use of short fiber-reinforced resin-based composite (SFRC) to replace dentin in a biomimetic approach. As endurance under mastication cycles is a significant consideration in the clinical success of resin-based composite posterior restorations, the use of SFRC as a base material may prevent restorative fracture due to the fibers' effectiveness in stopping cracks. This review article specifies the characteristics of SFRC and describes the major underlying mechanisms of short fiber reinforcement for resin-based composite. Insights are further taken from laboratory studies used to define the short fiber-related properties of resin-based composite and the performance of currently available materials, focusing on aspects that are relevant to the reinforcement of resin-based composite. Finally, future standpoints on the development of SFRCs with nano fibers and different resin monomers, and their role in digital dentistry, are discussed.

The health effects of short fiber chrysotile and amphibole asbestos

The potential toxic effects of short chrysotile and amphibole asbestos fibers with lengths <5 to ∼10 µm have been debated over the years. This stems from the large database of epidemiology, toxicology, and in-vitro studies, each of which often provides different information in understanding and differentiating the effects of short fibers. The epidemiology studies in which the cancer potency estimates were based upon relatively high exposure concentrations provide a conservative assessment that shorter fibers would have little if any effect, especially under controlled exposure or environmental conditions that may occur today. The QSAR models have shown that fiber aspect ratio and Mg content are excellent predictors of cancer potency and that short fibers/particles of amphibole would have no effect. The studies of motor vehicle mechanics and in particular workers who serviced chrysotile containing brakes with the majority of the fibers being short provides evidence that motor vehicle mechanics, including workers who were engaged in brake repair, are not at an increased risk of mesothelioma. Several inhalation toxicology studies clearly differentiated that short chrysotile and amphibole asbestos fibers did not produce a significant carcinogenic effect in the lung or pleural cavity. Because of dosing and lack of sensitivity to biosolubility, in vitro studies can be difficult to interpret; however, a number have differentiated short chrysotile and amphibole asbestos fibers from long fibers. Integral to understanding the importance of fiber length in determining possible health effects is an understanding of the biological and physiological function of the respiratory system. Short asbestos fibers, like innocuous dust, can be cleared through the tracheobronchial ciliated mucous transport, phagocytized by macrophages and cleared via the bronchial tree, and can also be removed through the lymphatic system. While the first two methods can remove them from the lung, with lymphatic transport through one-way valves, fibers are removed from the active area of the lung where the fiber-related disease has been shown to develop and can accumulate in lymphatic sumps and lymph nodes. While short asbestos fibers are present in most occupational or environmental exposures, the large body of studies strongly supports that they do not contribute to the health effects of asbestos exposure.

The influence of FRC base and bonded CAD/CAM resin composite endocrowns on fatigue behavior of cracked endodontically-treated molars

Cracked endodontically treated molars (ETMs) are commonly treated with full crowns. Less invasive techniques could include fiber-reinforced composite (FRC) base and adhesively bonded endocrowns. The purpose of this study was to assess the fatigue resistance of ETMs restored with CAD/CAM resin composite endocrowns and reinforced with different FRC bases. Cracks were simulated in fifty mandibular molars by cutting the teeth longitudinally and reassembling the two parts. After performing endodontic treatments and preparing cavities, teeth were restored in one of the following methods (n = 10). In Group 1, cavity floors were lined with 0.5 mm of flowable composite (Universal Injectable; GUI, shade A2). In Groups 2 and 3, the cavity floors were covered with one and three layers of FRC-net (ES Net) respectively, whereas in Groups 4 and 5 with 1 mm and 2 mm of flowable FRC-resin (EverX Flow Dentin; EXFD) respectively. Endocrowns (Cerasmart 270; CE, A2 HT) with 5 mm thickness were adhesively luted with preheated composite and all specimens were subjected to cyclic loading in water at 5 Hz, starting with a load of 600 N (5000 cycles), followed by stages of 1000, 1300, 1600, 1900, 2200 and 2500 at a maximum of 20 000 cycles each. Results were analyzed using Kaplan-Meier survival analysis and the Log-Rank test (p = 0.05). The fatigue failure load of ES Net applied in three layers (1617 N ± 371) or in one layer (1499 N ± 306), as well as EXFD applied in 2 mm (1496 N ± 264) or in 1 mm (1434 N ± 372) did not differ significantly (p > 0.05). Control teeth fractured at 1255 N ± 350 (p > 0.05). In the fiber-reinforced groups, restorable fractures were observed in 50%-80%, with only 30% deemed restorable in the control group. The fractures originated mainly at the occlusal contact points and the main crack propagated in the corono-apical direction. No crack origin (primary or secondary) starting from the artificial pre-existing crack was observed in fractured specimens. FRC bases did not improve the fatigue resistance of cracked ETMs, but favorably influenced the failure mode.

Enzymatic Pretreatment Coupled with the Addition of p-Hydroxyanisole Increased Levulinic Acid Production from Steam-Exploded Rice Straw Short Fiber

Levulinic acid production, directly from lignocellulosic biomass, resulted in low yields due to the poor substrate accessibility and occurrence of side reactions. The effects of reaction conditions, enzymatic pretreatment, and inhibitor addition on the conversion of steam-exploded rice straw (SERS) short fiber to levulinic acid catalyzed by solid superacid were investigated systematically. The results indicated that the optimal reaction conditions were temperature, time, and solid superacid concentration combinations of 200 °C, 15 min, and 7.5 %. Enzymatic pretreatment improved the substrate accessibility to solid superacid catalyst, and p-hydroxyanisole inhibitor reduced the side reactions during reaction processes, which helped to increase levulinic acid yield. The levulinic acid yield reached 25.2 % under the optimal conditions, which was 61.5 % higher than that without enzymatic pretreatment and inhibitor addition. Therefore, enzymatic pretreatment coupled with the addition of p-hydroxyanisole increased levulinic acid production effectively, which contributed to the value-added utilization of lignocellulosic biomass.