Tuning the morphology and chemical distribution of Ag atoms in Au rich nanoparticles using electrochemical dealloying

Dealloying of Ag-Au alloy nanoparticles (NPs) strongly differs from the corresponding bulk alloy materials. Here, we have investigated the effects of potentiodynamic and potentiostatic dealloying on structure and distribution of residual Ag atoms for Au rich NPs. Two different sizes of Ag rich alloy NPs, 77 ± 26 nm Ag77Au23 and 12 ± 5 nm Ag86Au14, were prepared. 77 nm Ag77Au23 NPs form a homogeneous alloy, while 12 nm Ag86Au14 NPs show an Ag rich shell-Au rich core arrangement. The two groups of as-prepared NPs were dealloyed either under potentiodynamic (0.2-1.3 VRHE) or potentiostatic (0.9, 1.2, and 1.6 VRHE) conditions in 0.1 M HClO4. For the initial 77 nm Ag77Au23 NPs, both dealloying protocols lead to pore evolution. Interestingly, instead of homogenous Ag distribution, numerous Ag rich regions form and locate near the pores and particle edges. The critical dealloying potential also differs by ∼500 mV depending on the dealloying method. The initial 12 nm Ag86Au14 NPs remain dense and solid, but Ag distribution and thickness of the Au passivation layer vary between both dealloying protocols. When the Au passivation layer is very thin, the residual Ag atoms tend to segregate to the particle surface after dealloying. Due to the size effect, small NPs are less electrochemically stable and show a lower critical dealloying potential. In this systematic study, we demonstrate that the mobility of Au surface atoms and dealloying conditions control the structure and residual Ag distribution within dealloyed NPs.

GaN atomic electric fields from a segmented STEM detector: Experiment and simulation

Atomic electric fields in a thin GaN sample are measured with the centre-of-mass approach in 4D-scanning transmission electron microscopy (4D-STEM) using a 12-segmented STEM detector in a Spectra 300 microscope. The electric fields, charge density and potential are compared to simulations and an experimental measurement using a pixelated 4D-STEM detector. The segmented detector benefits from a high recording speed, which enables measurements at low radiation doses. However, there is measurement uncertainty due to the limited number of segments analysed in this study.

Atom counting based on Voronoi averaged STEM intensities using a crosstalk correction scheme

If quantitative scanning transmission electron microscopy is used for very precise thickness measurements with atomic resolution, it is commonly referred to as »atom counting«. Due to scattering and the finite probe extent the signal recorded in one atomic column is dependent not only on its own height but also on the height of its neighbours. Especially for thicker specimens this crosstalk effect can have significant impact on the measured intensity. If it is not appropriately accounted for in the evaluation, it can result in a deterioration of accuracy that impedes the possibility of actual atom counting. However, as the number of possible neighbour configurations can be excessively large, a comprehensive consideration of all in the evaluation reference is neigh impossible. This work proposes a method that allows for the a-posteriori reduction of crosstalk during the evaluation by algebraic means. Based on a parametric model, which is described in detail in the article, the crosstalk is expressed by an invertible matrix. Applying the inverted matrix to the measurement yields crosstalk corrected intensity values with very little computational effort. These can subsequently be evaluated by direct comparison to simple reference data. The working principle of the method is presented on the example of crystalline gold. The crosstalk parametrisation is found by fitting a model to sets of specifically created multislice simulations. The parameters are given for both aberration corrected and uncorrected STEM. Subsequently the abilities and potential of the technique are assessed in simulative studies on multiple model systems including gold nanoparticles. Overall a significant and robust improvement of the attainable precision can be demonstrated making the proposed method a promising tool for reference-based atom counting.

Nanoporous Gold: From Structure Evolution to Functional Properties in Catalysis and Electrochemistry

Nanoporous gold (NPG) is characterized by a bicontinuous network of nanometer-sized metallic struts and interconnected pores formed spontaneously by oxidative dissolution of the less noble element from gold alloys. The resulting material exhibits decent catalytic activity for low-temperature, aerobic total as well as partial oxidation reactions, the oxidative coupling of methanol to methyl formate being the prototypical example. This review not only provides a critical discussion of ways to tune the morphology and composition of this material and its implication for catalysis and electrocatalysis, but will also exemplarily review the current mechanistic understanding of the partial oxidation of methanol using information from quantum chemical studies, model studies on single-crystal surfaces, gas phase catalysis, aerobic liquid phase oxidation, and electrocatalysis. In this respect, a particular focus will be on mechanistic aspects not well understood, yet. Apart from the mechanistic aspects of catalysis, best practice examples with respect to material preparation and characterization will be discussed. These can improve the reproducibility of the materials property such as the catalytic activity and selectivity as well as the scope of reactions being identified as the main challenges for a broader application of NPG in target-oriented organic synthesis.

Origin of the spectral red-shift and polarization patterns of self-assembled InGaN nanostructures on GaN nanowires

The luminescence of In_xGa_1-xN nanowires (NWs) is frequently reported with large red-shifts as compared to the theoretical value expected from the average In content. Both compositional fluctuations and radial built-in fields were considered accountable for this effect, depending on the size, structure, composition, and surrounding medium of the NWs. In the present work, the emission properties of InGaN/GaN NWs grown by plasma-assisted molecular beam epitaxy are investigated in a comprehensive study combining ultraviolet-Raman and photoluminescence spectroscopy (PL) on vertical arrays, polarization-dependent PL on bundles of a few NWs, scanning transmission electron microscopy, energy-dispersive X-ray spectroscopy, and calculations of the band profiles. The roles of inhomogeneous In distribution and radial fields in the context of optical emission properties are addressed. The radial built-in fields are found to be modest, with a maximum surface band bending below 350 meV. On the other hand, variations in the local In content have been observed that give rise to potential fluctuations whose impact on the emission properties is shown to prevail over band-bending effects. Two luminescence bands with large positive and moderate negative polarization ratios of ≈+80% and ≤-60%, respectively, were observed. The red-shift in the luminescence is associated with In-rich inclusions in the NWs due to thermodynamic decomposition during growth. The negative polarization anisotropy is suggested to result from spontaneously formed superlattices in the In-rich regions of the NWs. The NWs show a preferred orthogonal absorption due to the dielectric boundary conditions and highlight the extreme sensitivity of these structures towards light polarization.

Flame Aerosol Synthesis of Metal Sulfides at High Temperature in Oxygen-Lean Atmosphere

The development of a novel reactive spray technology based on the well-known gas-phase metal oxide synthesis route provides innumerable opportunities for the production of non-oxide nanoparticles. Among these materials, metal sulfides are expected to have a high impact, especially in the development of electrochemical and photochemical high-surface-area materials. As a proof-of-principle, MnS, CoS, Cu₂ S, ZnS, Ag₂ S, In₂ S₃ , SnS, and Bi₂ S₃ are synthesized in an O₂ -lean and sulfur-rich environment. In addition, the formation of Cu₂ S in a single-droplet combustion experiment is reported. The multiscale approach combining flame sprays with single-droplet combustion is expected to pave the way toward a fundamental understanding of the gas-phase formation of metal sulfides in the future. The knowledge acquired can open the possibility for the development of a next-generation gas-phase technology facilitating the scalable synthesis of functional binary/ternary metal sulfides.

Systematic Errors of Electric Field Measurements in Ferroelectrics by Unit Cell Averaged Momentum Transfers in STEM

When using the unit cell average of first moment data from four-dimensional scanning transmission electron microscopy (4D-STEM) to characterize ferroelectric materials, a variety of sources of systematic errors needs to be taken into account. In particular, these are the magnitude of the acceleration voltage, STEM probe semi-convergence angle, sample thickness, and sample tilt out of zone axis. Simulations show that a systematic error of calculated electric fields using the unit cell averaged momentum transfer originates from violation of point symmetry within the unit cells. Thus, values can easily exceed those of potential polarization-induced electric fields in ferroelectrics. Importantly, this systematic error produces deflection gradients between different domains seemingly representing measured fields. However, it could be shown that for PbZr0.2Ti0.8O3, many adjacent domains exhibit a relative crystallographic mistilt and in-plane rotation. The experimental results show that the method gives qualitative domain contrast. Comparison of the calculated electric field with the systematic error showed that the domain contrast of the unit cell averaged electric fields is mainly caused by dynamical scattering effects and the electric field plays only a minor role, if present at all.

Correlative analysis on InGaN/GaN nanowires: structural and optical properties of self-assembled short-period superlattices

The influence of self-assembled short-period superlattices (SPSLs) on the structural and optical properties of InGaN/GaN nanowires (NWs) grown by PAMBE on Si (111) was investigated by STEM, EDXS, µ-PL analysis and k·p simulations. STEM analysis on single NWs indicates that in most of the studied nanostructures, SPSLs self-assemble during growth. The SPSLs display short-range ordering of In-rich and In-poor In_xGa_1-xN regions with a period of 2-3 nm that are covered by a GaN shell and that transition to a more homogenous In_xGa_1-xN core. Polarization- and temperature-resolved PL analysis performed on the same NWs shows that they exhibit a strong parallel polarized red-yellow emission and a predominantly perpendicular polarized blue emission, which are ascribed to different In-rich regions in the nanostructures. The correlation between STEM, µ-PL and k·p simulations provides better understanding of the rich optical emission of complex III-N nanostructures and how they are impacted by structural properties, yielding the significant impact of strain on self-assembly and spectral emission.

Dose efficient annular bright field contrast with the ISTEM method: A proof of principle demonstration

The ISTEM mode for TEM has been demonstrated to have several advantages in regard to resolution and precision. While previous works primarily focussed on the advantages due to the reduced spatial coherence, the actual image contrast, i.e. how bright or dark certain atom columns are imaged, has mostly been of secondary concern. The present work sets out to achieve the contrast of annular bright field STEM in ISTEM, producing the high contrast of light elements, for which this method is popular. It is shown from theoretical considerations that using an annular condenser aperture this aim can be realised. The optimal size of this aperture is found by simulative studies. It is then manufactured from platinum foil and installed in an image-aberration corrected microscope. ABF-like ISTEM images of strontium titanate in [100] projection are acquired. The pure oxygen columns are clearly resolved with significant contrast. The image pattern is indeed identical to what is achieved by ABF STEM. A close look at the image formation also shows that the dose needed for a given signal-to-noise ratio is at least a quarter smaller for ABF-like ISTEM compared to ABF STEM, assuming detectors of similar detective quantum efficiency.

New Perspectives for Evaluating the Mass Transport in Porous Catalysts and Unfolding Macro- and Microkinetics

In this article we shed light on newly emerging perspectives to characterize and understand the interplay of diffusive mass transport and surface catalytic processes in pores of gas phase metal catalysts. As a case study, nanoporous gold, as an interesting example exhibiting a well-defined pore structure and a high activity for total and partial oxidation reactions is considered. PFG NMR (pulsed field gradient nuclear magnetic resonance) measurements allowed here for a quantitative evaluation of gas diffusivities within the material. STEM (scanning transmission electron microscopy) tomography furthermore provided additional insight into the structural details of the pore system, helping to judge which of its features are most decisive for slowing down mass transport. Based on the quantitative knowledge about the diffusion coefficients inside a porous catalyst, it becomes possible to disentangle mass transport contributions form the measured reaction kinetics and to determine the kinetic rate constant of the underlying catalytic surface reaction. In addition, predictions can be made for an improved effectiveness of the catalyst, i.e., optimized conversion rates. This approach will be discussed at the example of low-temperature CO oxidation, efficiently catalysed by npAu at 30 °C. The case study shall reveal that novel porous materials exhibiting well-defined micro- and mesoscopic features and sufficient catalytic activity, in combination with modern techniques to evaluate diffusive transport, offer interesting new opportunities for an integral understanding of catalytic processes.

Graphical Abstract

Quantitative 3D Characterization of Nanoporous Gold Nanoparticles by Transmission Electron Microscopy

Quantitative structural characterization of nanomaterials is important to tailor their functional properties. Corrosion of AgAu-alloy nanoparticles (NPs) results in porous structures, making them interesting for applications especially in the fields of catalysis and surface-enhanced Raman spectroscopy. For the present report, structures of dealloyed NPs were reconstructed three-dimensionally using scanning transmission electron microscopy tomography. These reconstructions were evaluated quantitatively, revealing structural information such as pore size, porosity, specific surface area, and tortuosity. Results show significant differences compared to the structure of dealloyed bulk samples and can be used as input for simulations of diffusion or mass transport processes, for example, in catalytic applications.

Synthesis and Characterization of Ligand-Linked Pt Nanoparticles: Tunable, Three-Dimensional, Porous Networks for Catalytic Hydrogen Sensing

Porous networks of Pt nanoparticles interlinked by bifunctional organic ligands have shown high potential as catalysts in micro-machined hydrogen gas sensors. By varying the ligand among p-phenylenediamine, benzidine, 4,4''-diamino-p-terphenyl, 1,5-diaminonaphthalene, and trans-1,4-diaminocyclohexane, new variants of such networks were synthesized. Inter-particle distances within the networks, determined via transmission electron microscopy tomography, varied from 0.8 to 1.4 nm in accordance with the nominal length of the respective ligand. While stable structures with intact and coordinatively bonded diamines were formed with all ligands, aromatic diamines showed superior thermal stability. The networks exhibited mesoporous structures depending on ligand and synthesis strategy and performed well as catalysts in hydrogen gas microsensors. They demonstrate the possibility of deliberately tuning micro- and mesoporosity and thereby transport properties and steric demands by choice of the right ligand also for other applications in heterogeneous catalysis.

Double Flame-Fabricated High-Performance AlPO4/LiMn2O4 Cathode Material for Li-Ion Batteries

The spinel LiMn₂O₄ (LMO) is a promising cathode material for rechargeable Li-ion batteries due to its excellent properties, including cost effectiveness, eco-friendliness, high energy density, and rate capability. The commercial application of LiMn₂O₄ is limited by its fast capacity fading during cycling, which lowers the electrochemical performance. In the present work, phase-pure and crystalline LiMn₂O₄ spinel in the nanoscale were synthesized using single flame spray pyrolysis via screening 16 different precursor-solvent combinations. To overcome the drawback of capacity fading, LiMn₂O₄ was homogeneously mixed with different percentages of AlPO₄ using versatile multiple flame sprays. The mixing was realized by producing AlPO₄ and LiMn₂O₄ aerosol streams in two independent flames placed at 20° to the vertical axis. The structural and morphological analyses by X-ray diffraction indicated the formation of a pure LMO phase and/or AlPO₄-mixed LiMn₂O₄. Electrochemical analysis indicated that LMO nanoparticles of 17.8 nm (d _BET) had the best electrochemical performance among the pure LMOs with an initial capacity and a capacity retention of 111.4 mA h g^-1 and 88% after 100 cycles, respectively. A further increase in the capacity retention to 93% and an outstanding initial capacity of 116.1 mA h g^-1 were acquired for 1% AlPO₄.

Control of Porous Layer Thickness in Thermophoretic Deposition of Nanoparticles

The film thickness plays an important role in the performance of materials applicable to different technologies including chemical sensors, catalysis and/or energy materials. The relationship between the surface and volume of the functional layers is key to high performance evaluations. Here we demonstrate the thermophoretic deposition of different thicknesses of the functional layers designed using flame combustion of tin 2-ethylhexanoate dissolved in xylene, and measurement of thickness by scanning electron microscopy and focused ion beam. The parameters such as spray fluid concentration (differing Sn2+ content), substrate-nozzle distance and time of the spray were considered to investigate the layer growth. The results showed ≈ 23, 124 and 161 μm thickness of the SnO2 layer after flame spray of 0.1, 0.5 M and 1.0 M tin 2-EHA-Xylene solutions for 1200 s. While Sn2+ concentration was 0.5 M for all the flame sprays, the substrates placed at 250, 220 and 200 mm from the flame nozzle had layer thicknesses of 113, 116 and 132 µm, respectively. Spray time dependent thickness growth showed a linear increase from 8.5 to 152.1 µm when the substrates were flame sprayed for 30 s to 1200 s using 0.5 M tin 2-EHA-Xylene solutions. Changing the dispersion oxygen flow (3-7 L/min) had almost no effect on layer thickness. Layers fabricated were compared to a model found in literature, which seems to describe the thickness well in the domain of varied parameters. It turned out that primary particle size deposited on the substrate can be tuned without altering the layer thickness and with little effect on porosity. Applications depending on porosity, such as catalysis or gas sensing, can benefit from tuning the layer thickness and primary particle size.

Quantitative Characterization of Nanometer-Scale Electric Fields via Momentum-Resolved STEM

Most of today's electronic devices, like solar cells and batteries, are based on nanometer-scale built-in electric fields. Accordingly, characterization of fields at such small scales has become an important task in the optimization of these devices. In this study, with GaAs-based p-n junctions as the example, key characteristics such as doping concentrations, polarity, and the depletion width are derived quantitatively using four-dimensional scanning transmission electron microscopy (4DSTEM). The built-in electric fields are determined by the shift they introduce to the center-of-mass of electron diffraction patterns at subnanometer spatial resolution. The method is applied successfully to characterize two p-n junctions with different doping concentrations. This highlights the potential of this method to directly visualize intentional or unintentional nanoscale electric fields in real-life devices, e.g., batteries, transistors, and solar cells.

Angle-resolved STEM using an iris aperture: Scattering contributions and sources of error for the quantitative analysis in Si

The angle-resolved electron scattering is investigated in scanning-transmission electron microscopy (STEM) using a motorised iris aperture placed above a conventional annular detector. The electron intensity scattered into various angle ranges is compared with simulations that were carried out in the frozen-lattice approximation. As figure of merit for the agreement of experiment and simulation we evaluate the specimen thickness which is compared with the thickness obtained from position-averaged convergent beam electron diffraction (PACBED). We find deviations whose strengths depend on the angular range of the detected electrons. As possible sources of error we investigate, for example, the influences of amorphous surface layers, inelastic scattering (plasmon excitation), phonon-correlation within the frozen-lattice approach, and distortions in the diffraction plane of the microscope. The evaluation is performed for four experimental thicknesses and two angle-resolved STEM series under different camera lengths. The results clearly show that especially for scattering angles below 50 mrad, it is mandatory that the simulations take scattering effects into account which are usually neglected for simulating high-angle scattering. Most influences predominantly affect the low-angle range, but also high scattering angles can be affected (e.g. by amorphous surface covering).

The gas-phase formation of tin dioxide nanoparticles in single droplet combustion and flame spray pyrolysis

Tin dioxide (SnO₂) nanoparticles synthesized via flame spray pyrolysis (FSP) have promising applications for gas sensors. The formation of SnO₂ nanoparticles in the gas-phase has been investigated using single droplet combustion and FSP. Precursor solutions of Tin (II) 2-ethylhexanoate dissolved in Xylene with varying Sn concentrations were selected as the precursor-solvent system. The selected precursor-solvent system has its stability and ability to synthesize homogeneous nanoparticles, compared to metal nitrate based precursor solutions. The precursor-solvent system was studied using attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy and thermogravimetric analysis (TGA). The SnO₂ nanoparticles were characterized using X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), and transmission electron microscopy (TEM). Droplet surface micro-explosions were observed during the single droplet combustion of the precursor solutions. It is because of the heterogeneous vapor-phase nucleation, which is beneath the liquid droplet surface and caused by precursor thermal decomposition. The results show that the size of nanoparticles obtained both from FSP and single droplet combustion increases with increasing metal-precursor concentration. The TEM images of the particles from such droplet combustion reveal two types of nanoparticles with different sizes and morphologies. The current work provides fundamental understanding of precursor decomposition and particle formation during single droplet combustion, which help in-depth understanding of the flame spray pyrolysis.

Electrical Polarization in AlN/GaN Nanodisks Measured by Momentum-Resolved 4D Scanning Transmission Electron Microscopy

We report the mapping of polarization-induced internal electric fields in AlN/GaN nanowire heterostructures at unit cell resolution as a key for the correlation of optical and structural phenomena in semiconductor optoelectronics. Momentum-resolved aberration-corrected scanning transmission electron microscopy is employed as a new imaging mode that simultaneously provides four-dimensional data in real and reciprocal space. We demonstrate how internal mesoscale and atomic electric fields can be separated in an experiment, which is verified by comprehensive dynamical simulations of multiple electron scattering. A mean difference of 5.3±1.5  MV/cm is found for the polarization-induced electric fields in AlN and GaN, being in accordance with dedicated simulations and photoluminescence measurements in previous publications.

Nanoporous gold functionalized with praseodymia-titania mixed oxides as a stable catalyst for the water-gas shift reaction

Dealloyed nanoporous metals hold great promise in the field of heterogeneous catalysis; however their tendency to coarsen at elevated temperatures or under catalytic reaction conditions sometimes limit further applications. Here, we report on a highly stable nanoporous gold catalyst (npAu) functionalized with praseodymia-titania mixed oxides as synthesized by a sol-gel method. Specifically, we used aberration-corrected transmission electron microscopy to study the morphology and the interface between the oxide deposits and the npAu substrate at the atomic level. Based on electron energy loss spectroscopy (EELS), it is concluded that Pr-TiOx mixed oxides form a solid solution. Flow reactor tests reveal that the Pr-TiOx functionalized nanoporous gold is not only highly active but also very stable for the water gas shift reaction in a large temperature range (180-400 °C). Our results demonstrate the potential of engineering the compositions of oxides coatings on npAu for advanced functional systems.

Using molecular dynamics for multislice TEM simulation of thermal diffuse scattering in AlGaN

For simulation of transmission electron microscopic images and diffraction patterns, the accurate inclusion of thermal diffuse scattering by phonons is important. In the frozen phonon multislice algorithm, this is possible, if thermal displacements according to the realistic, quantum mechanical distribution can be generated. For pure crystals, quantum mechanical calculations based on DFT yield those displacements. But for alloys one is usually restricted to the Einstein approximation, where correlations between atoms are neglected. In this article, molecular dynamics simulations are discussed and used as an alternative method for displacement calculation. Employing an empirical Stillinger-Weber type potential, classical motion is used as an approximation for the quantum mechanical dynamics. Thereby, correlations and possible static atomic displacements are inherently included. An appropriate potential is devised for AlGaN by fitting to force constant matrices determined from DFT and elastic constants of AlN and GaN. A comparison shows that the empiric potential reproduces phonon dispersions and displacement expectations from DFT references. The validity for alloys is successfully demonstrated by comparison to DFT calculations in special quasirandom structures. Subsequently, molecular dynamics were used in multislice simulations of both conventional and scanning TEM images. The resulting images are in very good agreement with DFT based calculations, while a slight yet significant deviation from Einstein approximation results can be seen, which can be attributed to the neglect of correlations in the latter. The presented potential hence proves to be a useful tool for accurate TEM simulations of AlGaN alloys.

Ultrathin Au-Alloy Nanowires at the Liquid-Liquid Interface

Ultrathin bimetallic nanowires are of importance and interest for applications in electronic devices such as sensors and heterogeneous catalysts. In this work, we have designed a new, highly reproducible and generalized wet chemical method to synthesize uniform and monodispersed Au-based alloy (AuCu, AuPd, and AuPt) nanowires with tunable composition using microwave-assisted reduction at the liquid-liquid interface. These ultrathin alloy nanowires are below 4 nm in diameter and about 2 μm long. Detailed microstructural characterization shows that the wires have an face centred cubic (FCC) crystal structure, and they have low-energy twin-boundary and stacking-fault defects along the growth direction. The wires exhibit remarkable thermal and mechanical stability that is critical for important applications. The alloy wires exhibit excellent electrocatalytic activity for methanol oxidation in an alkaline medium.

Steam reforming of methanol over oxide decorated nanoporous gold catalysts: a combined in situ FTIR and flow reactor study

Methanol as a green and renewable resource can be used to generate hydrogen by reforming, i.e., its catalytic oxidation with water. In combination with a fuel cell this hydrogen can be converted into electrical energy, a favorable concept, in particular for mobile applications. Its realization requires the development of novel types of structured catalysts, applicable in small scale reactor designs. Here, three different types of such catalysts were investigated for the steam reforming of methanol (SRM). Oxides such as TiO₂ and CeO₂ and mixtures thereof (Ce₁Ti₂O_x) were deposited inside a bulk nanoporous gold (npAu) material using wet chemical impregnation procedures. Transmission electron and scanning electron microscopy reveal oxide nanoparticles (1-2 nm in size) abundantly covering the strongly curved surface of the nanoporous gold host (ligaments and pores on the order of 40 nm in size). These catalysts were investigated in a laboratory scaled flow reactor. First conversion of methanol was detected at 200 °C. The measured turn over frequency at 300 °C of the CeO_x/npAu catalyst was 0.06 s^-1. Parallel investigation by in situ infrared spectroscopy (DRIFTS) reveals that the activation of water and the formation of OH_ads are the key to the activity/selectivity of the catalysts. While all catalysts generate sufficient OH_ads to prevent complete dehydrogenation of methanol to CO, only the most active catalysts (e.g., CeO_x/npAu) show direct reaction with formic acid and its decomposition to CO₂ and H₂. The combination of flow reactor studies and in operando DRIFTS, thus, opens the door to further development of this type of catalyst.

Screening Precursor-Solvent Combinations for Li4Ti5O12 Energy Storage Material Using Flame Spray Pyrolysis

The development and industrial application of advanced lithium based energy-storage materials are directly related to the innovative production techniques and the usage of inexpensive precursor materials. Flame spray pyrolysis (FSP) is a promising technique that overcomes the challenges in the production processes such as scalability, process control, material versatility, and cost. In the present study, phase pure anode material Li₄Ti₅O₁₂ (LTO) was designed using FSP via extensive systematic screening of lithium and titanium precursors dissolved in five different organic solvents. The effect of precursor and solvent parameters such as chemical reactivity, boiling point, and combustion enthalpy on the particle formation either via gas-to-particle (evaporation/nucleation/growth) or via droplet-to-particle (precipitation/incomplete evaporation) is discussed. The presence of carboxylic acid in the precursor solution resulted in pure (>95 mass %) and homogeneous LTO nanoparticles of size 4-9 nm, attributed to two reasons: (1) stabilization of water sensitive metal alkoxides precursor and (2) formation of volatile carboxylates from lithium nitrate evidenced by attenuated total reflection Fourier transform infrared spectroscopy and single droplet combustion experiments. In contrast, the absence of carboxylic acids resulted in larger inhomogeneous crystalline titanium dioxide (TiO₂) particles with significant reduction of LTO content as low as ∼34 mass %. In-depth particle characterization was performed using X-ray diffraction with Rietveld refinement, thermogravimetric analysis coupled with differential scanning calorimetry and mass spectrometry, gas adsorption, and vibrational spectroscopy. High-resolution transmission electron microscopy of the LTO product revealed excellent quality of the particles obtained at high temperature. In addition, high rate capability and efficient charge reversibility of LTO nanoparticles demonstrate the vast potential of inexpensive gas-phase synthesis for energy-storage materials.

The microstructure, local indium composition and photoluminescence in green-emitting InGaN/GaN quantum wells

In this work, we analyse the microstructure and local chemical composition of green-emitting In_x Ga_1-x N/GaN quantum well (QW) heterostructures in correlation with their emission properties. Two samples of high structural quality grown by metalorganic vapour phase epitaxy (MOVPE) with a nominal composition of x = 0.15 and 0.18 indium are discussed. The local indium composition is quantitatively evaluated by comparing scanning transmission electron microscopy (STEM) images to simulations and the local indium concentration is extracted from intensity measurements. The calculations point out that the measured indium fluctuations may be correlated to the large width and intensity decrease of the PL emission peak.

Bias-Controlled Optical Transitions in GaN/AlN Nanowire Heterostructures

We report on the control and modification of optical transitions in 40× GaN/AlN heterostructure superlattices embedded in GaN nanowires by an externally applied bias. The complex band profile of these multi-nanodisc heterostructures gives rise to a manifold of optical transitions, whose emission characteristic is strongly influenced by polarization-induced internal electric fields. We demonstrate that the superposition of an external axial electric field along a single contacted nanowire leads to specific modifications of each photoluminescence emission, which allows to investigate and identify their origin and to control their characteristic properties in terms of transition energy, intensity and decay time. Using this approach, direct transitions within one nanodisc, indirect transitions between adjacent nanodiscs, transitions at the top/bottom edge of the heterostructure, and the GaN near-band-edge emission can be distinguished. While the transition energy of the direct transition can be shifted by external bias over a range of 450 meV and changed in intensity by a factor of 15, the indirect transition exhibits an inverse bias dependence and is only observable and spectrally separated when external bias is applied. In addition, by tuning the band profile close to flat band conditions, the direction and magnitude of the internal electric field can be estimated, which is of high interest for the polar group III-nitrides. The direct control of emission properties over a wide range bears possible application in tunable optoelectronic devices. For more fundamental studies, single-nanowire heterostructures provide a well-defined and isolated system to investigate and control interaction processes in coupled quantum structures.

Entropy-limited topological protection of skyrmions

Magnetic skyrmions are topologically protected whirls that decay through singular magnetic configurations known as Bloch points. We used Lorentz transmission electron microscopy to infer the energetics associated with the topological decay of magnetic skyrmions far from equilibrium in the chiral magnet Fe_1-x Co _x Si. We observed that the lifetime τ of the skyrmions depends exponentially on temperature, [Formula: see text]. The prefactor τ₀ of this Arrhenius law changes by more than 30 orders of magnitude for small changes of the magnetic field, reflecting a substantial reduction of the lifetime of skyrmions by entropic effects and, thus, an extreme case of enthalpy-entropy compensation. Such compensation effects, being well known across many different scientific disciplines, affect topological transitions and, thus, topological protection on an unprecedented level.

Measurement of atomic electric fields and charge densities from average momentum transfers using scanning transmission electron microscopy

This study sheds light on the prerequisites, possibilities, limitations and interpretation of high-resolution differential phase contrast (DPC) imaging in scanning transmission electron microscopy (STEM). We draw particular attention to the well-established DPC technique based on segmented annular detectors and its relation to recent developments based on pixelated detectors. These employ the expectation value of the momentum transfer as a reliable measure of the angular deflection of the STEM beam induced by an electric field in the specimen. The influence of scattering and propagation of electrons within the specimen is initially discussed separately and then treated in terms of a two-state channeling theory. A detailed simulation study of GaN is presented as a function of specimen thickness and bonding. It is found that bonding effects are rather detectable implicitly, e.g., by characteristics of the momentum flux in areas between the atoms than by directly mapping electric fields and charge densities. For strontium titanate, experimental charge densities are compared with simulations and discussed with respect to experimental artifacts such as scan noise. Finally, we consider practical issues such as figures of merit for spatial and momentum resolution, minimum electron dose, and the mapping of larger-scale, built-in electric fields by virtue of data averaged over a crystal unit cell. We find that the latter is possible for crystals with an inversion center. Concerning the optimal detector design, this study indicates that a sampling of 5mrad per pixel is sufficient in typical applications, corresponding to approximately 10×10 available pixels.

Atomic resolution elemental mapping using energy-filtered imaging scanning transmission electron microscopy with chromatic aberration correction

This paper addresses a novel approach to atomic resolution elemental mapping, demonstrating a method that produces elemental maps with a similar resolution to the established method of electron energy-loss spectroscopy in scanning transmission electron microscopy. Dubbed energy-filtered imaging scanning transmission electron microscopy (EFISTEM) this mode of imaging is, by the quantum mechanical principle of reciprocity, equivalent to tilting the probe in energy-filtered transmission electron microscopy (EFTEM) through a cone and incoherently averaging the results. In this paper we present a proof-of-principle EFISTEM experimental study on strontium titanate. The present approach, made possible by chromatic aberration correction, has the advantage that it provides elemental maps which are immune to spatial incoherence in the electron source, coherent aberrations in the probe-forming lens and probe jitter. The veracity of the experiment is supported by quantum mechanical image simulations, which provide an insight into the image-forming process. Elemental maps obtained in EFTEM suffer from the effect known as preservation of elastic contrast, which, for example, can lead to a given atomic species appearing to be in atomic columns where it is not to be found. EFISTEM very substantially reduces the preservation of elastic contrast and yields images which show stability of contrast with changing thickness. The experimental application is demonstrated in a proof-of-principle study on strontium titanate.

The structure of denisovite, a fibrous nanocrystalline polytypic disordered 'very complex' silicate, studied by a synergistic multi-disciplinary approach employing methods of electron crystallography and X-ray powder diffraction

Denisovite is a rare mineral occurring as aggregates of fibres typically 200-500 nm diameter. It was confirmed as a new mineral in 1984, but important facts about its chemical formula, lattice parameters, symmetry and structure have remained incompletely known since then. Recently obtained results from studies using microprobe analysis, X-ray powder diffraction (XRPD), electron crystallography, modelling and Rietveld refinement will be reported. The electron crystallography methods include transmission electron microscopy (TEM), selected-area electron diffraction (SAED), high-angle annular dark-field imaging (HAADF), high-resolution transmission electron microscopy (HRTEM), precession electron diffraction (PED) and electron diffraction tomography (EDT). A structural model of denisovite was developed from HAADF images and later completed on the basis of quasi-kinematic EDT data by ab initio structure solution using direct methods and least-squares refinement. The model was confirmed by Rietveld refinement. The lattice parameters are a = 31.024 (1), b = 19.554 (1) and c = 7.1441 (5) Å, β = 95.99 (3)°, V = 4310.1 (5) ų and space group P12/a1. The structure consists of three topologically distinct dreier silicate chains, viz. two xonotlite-like dreier double chains, [Si₆O₁₇]^10-, and a tubular loop-branched dreier triple chain, [Si₁₂O₃₀]^12-. The silicate chains occur between three walls of edge-sharing (Ca,Na) octahedra. The chains of silicate tetrahedra and the octahedra walls extend parallel to the z axis and form a layer parallel to (100). Water molecules and K⁺ cations are located at the centre of the tubular silicate chain. The latter also occupy positions close to the centres of eight-membered rings in the silicate chains. The silicate chains are geometrically constrained by neighbouring octahedra walls and present an ambiguity with respect to their z position along these walls, with displacements between neighbouring layers being either Δz = c/4 or -c/4. Such behaviour is typical for polytypic sequences and leads to disorder along [100]. In fact, the diffraction pattern does not show any sharp reflections with l odd, but continuous diffuse streaks parallel to a* instead. Only reflections with l even are sharp. The diffuse scattering is caused by (100) nano-lamellae separated by stacking faults and twin boundaries. The structure can be described according to the order-disorder (OD) theory as a stacking of layers parallel to (100).

Nanoscopic Insights into InGaN/GaN Core-Shell Nanorods: Structure, Composition, and Luminescence

Nitride-based three-dimensional core-shell nanorods (NRs) are promising candidates for the achievement of highly efficient optoelectronic devices. For a detailed understanding of the complex core-shell layer structure of InGaN/GaN NRs, a systematic determination and correlation of the structural, compositional, and optical properties on a nanometer-scale is essential. In particular, the combination of low-temperature cathodoluminescence (CL) spectroscopy directly performed in a scanning transmission electron microscope (STEM), and quantitative high-angle annular dark field imaging enables a comprehensive study of the nanoscopic attributes of the individual shell layers. The investigated InGaN/GaN core-shell NRs, which were grown by metal-organic vapor-phase epitaxy using selective-area growth exhibit an exceptionally low density of extended defects. Using highly spatially resolved CL mapping of single NRs performed in cross-section, we give a direct insight into the optical properties of the individual core-shell layers. Most interesting, we observe a red shift of the InGaN single quantum well from 410 to 471 nm along the nonpolar side wall. Quantitative STEM analysis of the active region reveals an increasing thickness of the single quantum well (SQW) from 6 to 13 nm, accompanied by a slight increase of the indium concentration along the nonpolar side wall from 11% to 13%. Both effects, the increased quantum-well thickness and the higher indium incorporation, are responsible for the observed energetic shift of the InGaN SQW luminescence. Furthermore, compositional mappings of the InGaN quantum well reveal the formation of locally indium rich regions with several nanometers in size, leading to potential fluctuations in the InGaN SQW energy landscape. This is directly evidenced by nanometer-scale resolved CL mappings that show strong localization effects of the excitonic SQW emission.

Direct Measurement of Polarization-Induced Fields in GaN/AlN by Nano-Beam Electron Diffraction

The built-in piezoelectric fields in group III-nitrides can act as road blocks on the way to maximizing the efficiency of opto-electronic devices. In order to overcome this limitation, a proper characterization of these fields is necessary. In this work nano-beam electron diffraction in scanning transmission electron microscopy mode has been used to simultaneously measure the strain state and the induced piezoelectric fields in a GaN/AlN multiple quantum well system.

A versatile sol–gel coating for mixed oxides on nanoporous gold and their application in the water gas shift reaction

Ceria–titania mixed oxides on a structured nanoporous gold support result in highly active and durable catalysts for the water-gas shift reaction.

Reactive oxygen species (ROS) formation ability and stability of small copper (Cu) nanoparticles (NPs)

In the presence of H₂O₂, Cu nanoparticles degrade to Cu cations which generate highly reactive ROS.