One Step Closer to Coatings Applications Utilizing Self-Stratification: Effect of Rheology Modifiers

Self-stratification of model blends of colloidal spheres has recently been demonstrated as a method to form multifunctional coatings in a single pass. However, practical coating formulations are complex fluids with upward of 15 components. Here, we investigate the influence of three different rheology modifiers (RMs) on the stratification of a 10 wt % 7:3 w:w blend of 270 and 96 nm anionic latex particles that do not stratify without RM. However, addition of a high molar mass polysaccharide thickener, xanthan gum, raises the viscosity and corresponding Péclet number enough to achieve small-on-top stratification as demonstrated by atomic force microscopy (AFM) measurements. Importantly, this was possible due to minimal particle-rheology modifier interactions, as demonstrated by the bulk rheology. In contrast, Carbopol 940, a microgel-based RM, was unable to achieve small-on-top stratification despite a comparable increase in viscosity. Instead, pH-dependent interactions with latex particles lead to either laterally segregated structures at pH 3 or a surface enrichment of large particles at pH 8. Strong RM-particle interactions are also observed when the triblock associative RM HEUR10kC12 is used. Here, small-on-top, large-enhanced, and randomly mixed structures were observed at respectively 0.01, 0.1, and 1 wt % HEUR10kC12. Combining rheology, dynamic light scattering, and AFM results allows the mechanisms behind the nonmonotonic stratification in the presence of associative RMs to be elucidated. Our results highlight that stratification can be predicted and controlled for RMs with weak particle interactions, while a strong RM-particle interaction may afford a wider range of stratified structures. This takes a step toward successfully harnessing stratification in coatings formulations.

Well-Defined Thermo-Responsive Copolymers Based on Oligo(Ethylene Glycol) Methacrylate and Pentafluorostyrene for the Removal of Organic Dyes from Water

Thermo-responsive copolymers based on oligo(ethylene glycol) methacrylate (OEGMA, Mn = 300 g/mol) and pentafluorostyrene (PFS), coded PFG, were synthesized by RAFT polymerization, using a trithiocarbonate (CTTPC) as controlling agent. Different molar masses were targeted and dispersities lower than 1.51 were obtained. The thermally triggered self-assembly of the resulting PFG copolymers in water was investigated by dynamic light scattering (DLS). The lower critical solution temperature (LCST) slightly increased with the molecular weight in the 26-30 °C temperature range, whereas the sizes of the intermicellar aggregates formed upon self-assembly tended to decrease with increasing molecular weights (ranging from 1415 to 572 nm). The resulting thermally-induced polymer aggregates were then used to encapsulate and remove organic contaminants from water. Nile Red (NR) and Thiazole yellow G (TYG) were employed as hydrophobic and hydrophilic model contaminants, respectively. Experimental results evidenced that higher molecular weight copolymers removed up to 90% of NR from aqueous solution, corresponding to about 10 mg of dye per g of copolymer, regardless of NR concentration. The removal of TYG was lower with respect to NR, decreasing from about 40% to around 20% with TYG concentration. Finally, the copolymers were shown to be potentially recycled and reused in the treatment of contaminated water.

Intercalation and structural aspects of macroRAFT agents into MgAl layered double hydroxides

Increasing attention has been devoted to the design of layered double hydroxide (LDH)-based hybrid materials. In this work, we demonstrate the intercalation by anion exchange process of poly(acrylic acid) (PAA) and three different hydrophilic random copolymers of acrylic acid (AA) and n-butyl acrylate (BA) with molar masses ranging from 2000 to 4200 g mol^-1 synthesized by reversible addition-fragmentation chain transfer (RAFT) polymerization, into LDH containing magnesium(II) and aluminium(III) intralayer cations and nitrates as counterions (MgAl-NO₃ LDH). At basic pH, the copolymer chains (macroRAFT agents) carry negative charges which allowed the establishment of electrostatic interactions with the LDH interlayer and their intercalation. The resulting hybrid macroRAFT/LDH materials displayed an expanded interlamellar domain compared to pristine MgAl-NO₃ LDH from 1.36 nm to 2.33 nm. Depending on the nature of the units involved into the macroRAFT copolymer (only AA or AA and BA), the intercalation led to monolayer or bilayer arrangements within the interlayer space. The macroRAFT intercalation and the molecular structure of the hybrid phases were further characterized by Fourier transform infrared (FTIR) and solid-state ¹³C, ¹H and ²⁷Al nuclear magnetic resonance (NMR) spectroscopies to get a better description of the local structure.

Well-Defined Amphiphilic Block Copolymer Nanoobjects via Nitroxide-Mediated Emulsion Polymerization

Water-soluble macroalkoxyamines are shown to be particularly well-suited initiators for nitroxide-mediated emulsion polymerization. They lead to the synthesis of amphiphilic block copolymers that self-assemble in situ into well-defined nanoobject morphologies, in agreement with the principles of polymerization-induced micellization. Depending on the molar mass of the hydrophobic block, the formed nanoparticles are hairy spherical micelles, nanofibers, or vesicles. The nanofibers are the most intriguing and spectacular structure and strongly affect the physicochemical properties of the aqueous dispersions.