Anomalous enhancement of thermoelectric power factor in multiple two-dimensional electron gas system

Toward drastic enhancement of thermoelectric power factor, quantum confinement effect proposed by Hicks and Dresselhaus has intrigued a lot of researchers. There has been much effort to increase power factor using step-like density-of-states in two-dimensional electron gas (2DEG) system. Here, we pay attention to another effect caused by confining electrons spatially along one-dimensional direction: multiplied 2DEG effect, where multiple discrete subbands contribute to electrical conduction, resulting in high Seebeck coefficient. The power factor of multiple 2DEG in GaAs reaches the ultrahigh value of ~100 μWcm-1 K-2 at 300 K. We evaluate the enhancement rate defined as power factor of 2DEG divided by that of three-dimensional bulk. The experimental enhancement rate relative to the theoretical one of conventional 2DEG reaches anomalously high (~4) in multiple 2DEG compared with those in various conventional 2DEG systems (~1). This proposed methodology for power factor enhancement opens the next era of thermoelectric research.

Low Dark Current Operation in InAs/GaAs(111)A Infrared Photodetectors: Role of Misfit Dislocations at the Interface

We demonstrate an extended short-wave infrared (e-SWIR) photodetector composed of an InAs/GaAs(111)A heterostructure with interface misfit dislocations. The layer structure of the photodetector consists simply of an n-InAs optical absorption layer directly grown with a thin undoped-GaAs spacer layer on n-GaAs by molecular beam epitaxy. The lattice mismatch was abruptly relaxed by forming a misfit dislocation network at the initial stage of the InAs growth. We found high-density threading dislocations (1.5 × 10⁹ cm^-2) in the InAs layer. The current-voltage characteristics of the photodetector at 77 K had a very low dark current density (<1 × 10^-9 A cm^-2) at a positive applied voltage (electrons flow from n-GaAs to n-InAs) of up to ∼+1 V. Simulation of the band structure revealed that the direct connection of GaAs and InAs and the formation of interfacial states by the misfit dislocations play significant positive roles in suppressing dark current. Under illumination with e-SWIR light at 77 K, a clear photocurrent signal was observed with a 2.6 μm cutoff wavelength, which is consistent with the bandgap of InAs. We also demonstrated e-SWIR detection at room temperature with a 3.2 μm cutoff wavelength. The maximum detectivity at 294 K exceeds 2 × 10⁸ cm Hz^0.5 W^-1 for the detection of e-SWIR light at 2 μm.

Relationship between surgical field contamination by patient's exhaled air and the state of the drapes during eye surgery

The coronavirus disease (COVID-19) pandemic has led to a dramatic increase in facemask use. Consequently, it has been reported that exhaled airflow toward the eyes can cause the dispersal of bacteria into the eyes, potentially increasing the incidence of postoperative endophthalmitis. In addition to wearing a facemask, gaps between the surgical drape and skin can also direct exhaled airflow toward the eyes. Here, we aimed to examine how the risk of contamination varies depending on the state of the drapes. We used a carbon dioxide imaging camera to visualize changes in exhaled airflow under different drape conditions and a particle counter to evaluate changes in the number of particles around the eye. The results revealed airflow present around the eye and a significant increase in the number of particles when the nasal side of the drape was detached from the skin. However, when a metal rod called "rihika" was used to create space above the body, the airflow and number of particles were significantly reduced. Thus, if drape coverage becomes incomplete during surgery, exhaled airflow toward the eye may contaminate the surgical field. On hanging up the drape, airflow can escape in the direction of the body, potentially preventing contamination.

High-endurance micro-engineered LaB6 nanowire electron source for high-resolution electron microscopy

The size tunability and chemical versatility of nanostructures enable electron sources of high brightness and temporal coherence, both of which are important characteristics for high-resolution electron microscopy^1-3. Despite intensive research efforts in the field, so far, only conventional field emitters based on a bulk tungsten (W) needle have been able to yield atomic-resolution images. The absence of viable alternatives is in part caused by insufficient fabrication precision for nanostructured sources, which require an alignment precision of subdegree angular deviation of a nanometre-sized emission area with the macroscopic emitter axis⁴. To overcome this challenge, in this work we micro-engineered a LaB₆ nanowire-based electron source that emitted a highly collimated electron beam with good lateral and angular alignment. We integrated a passive collimator structure into the support needle tip for the LaB₆ nanowire emitter. The collimator formed an axially symmetric electric field around the emission tip of the nanowire. Furthermore, by means of micromanipulation, the support needle tip was bent to align the emitted electron beam with the emitter axis. After installation in an aberration-corrected transmission electron microscope, we characterized the performance of the electron source in a vacuum of 10^-8 Pa and achieved atomic resolution in both broad-beam and probe-forming modes at 60 kV beam energy. The natural, unmonochromated 0.20 eV electron energy loss spectroscopy resolution, 20% probe-forming efficiency and 0.4% probe current peak-to-peak noise ratio paired with modest vacuum requirements make the LaB₆ nanowire-based electron source an attractive alternative to the standard W-based sources for low-cost electron beam instruments.

Patchwork metasurface quantum well photodetectors with broadened photoresponse

Complex lightwave manipulation such as broadband absorption has been realized with metasurfaces based on laterally arranged metal-dielectric-metal cavities with different geometries. However, application of these metasurfaces for optoelectronic devices by incorporating functional dielectrics remains challenging. Here, we integrate a quantum well infrared photodetector (QWIP) with a metasurface made of a patchwork of square cavities with different dimensions arranged in a subwavelength unit cell. Our detector realizes wideband photoresponse approaching the entire responsivity spectrum of the QWIP-single-sized square cavities can utilize only 60% of the possible bandwidth-and external quantum efficiencies of up to 78% at 6.8 µm. Our highly flexible design scheme enables integration of photodetectors and metasurfaces with arbitrary arrangements of cavities selectively responding to incidence with a specific wavefront.

Synchronously wired infrared antennas for resonant single-quantum-well photodetection up to room temperature

Optical patch antennas sandwiching dielectrics between metal layers have been used as deep subwavelength building blocks of metasurfaces for perfect absorbers and thermal emitters. However, for applications of these metasurfaces for optoelectronic devices, wiring to each electrically isolated antenna is indispensable for biasing and current flow. Here we show that geometrically engineered metallic wires interconnecting the antennas can function to synchronize the optical phases for promoting coherent resonance, not only as electrical conductors. Antennas connected with optimally folded wires are applied to intersubband infrared photodetectors with a single 4-nm-thick quantum well, and a polarization-independent external quantum efficiency as high as 61% (responsivity 3.3 A W⁻¹, peak wavelength 6.7 μm) at 78 K, even extending to room temperature, is demonstrated. Applications of synchronously wired antennas are not limited to photodetectors, but are expected to serve as a fundamental architecture of arrayed subwavelength resonators for optoelectronic devices such as emitters and modulators.

Applications of metasurfaces for optoelectronic devices require wiring to each isolated antenna for biasing and current flow. Here, the authors report optimal wire interconnects design for controlling the optical properties and present antenna-enhanced mid-infrared photodetection incorporating a single quantum well.

Double-Sided Nonalloyed Ohmic Contacts to Si-doped GaAs for Plasmoelectronic Devices

There is increasing demand for the ability to form ohmic contacts without lossy intermediate layers on both the top and bottom sides of metal-semiconductor-metal plasmoelectronic devices such as quantum cascade lasers and metasurface photodetectors. Although highly Si-doped n-GaAs surfaces can allow an ohmic contact without alloying, conditions for realizing nonalloyed ohmic contacts to other n-GaAs surfaces, originally buried inside but exposed by removing the substrate, have yet to be studied. We discovered that nonalloyed ohmic contacts to initially buried surfaces with a practically low contact resistivity down to 77 K can be realized by fulfilling certain requirements, specifically keeping the Si-doping concentration within a narrow range of 7.5 × 1018 to 1.25 × 1019 cm-3 and setting the growth temperature of the succeeding upper layers to a low value of 530 °C.

Scattering-angle-dependent Christiansen color spectra data of poly(vinyl chloride) (PVC) suspended in styrene liquid and a comprehensive data list of wavelength-dependent refractive indices of PVC

This paper reports transmission and scattering spectra of poly(vinyl chloride) (PVC) in styrene liquid, which is derived from Christiansen effect. The spectra were measured by varying scattering angles. Further discussion on Christiansen color was provided in the paper entitled "Transmitting and scattering colors of porous particles of poly(vinyl chloride) based on Christiansen effect" (Samitsu et al., 2018) [1]. The paper additionally provides refractive indices of PVC reported in literatures because Christiansen effect has close relationship with wavelength-dependent refractive index, i.e. optical dispersion. The values have considerable range probably depending on samples and determination methods for refractive index. The comprehensive data list is therefore potentially useful for studying refractive index of polymers.

Selective Plasmonic Enhancement of Electric- and Magnetic-Dipole Radiations of Er Ions

Lanthanoid series are unique in atomic elements. One reason is because they have 4f electronic states forbidding electric-dipole (ED) transitions in vacuum and another reason is because they are very useful in current-day optical technologies such as lasers and fiber-based telecommunications. Trivalent Er ions are well-known as a key atomic element supporting 1.5 μm band optical technologies and also as complex photoluminescence (PL) band deeply mixing ED and magnetic-dipole (MD) transitions. Here we show large and selective enhancement of ED and MD radiations up to 83- and 26-fold for a reference bulk state, respectively, in experiments employing plasmonic nanocavity arrays. We achieved the marked PL enhancement by use of an optimal design for electromagnetic (EM) local density of states (LDOS) and by Er-ion doping in deep subwavelength precision. We moreover clarify the quantitative contribution of ED and MD radiations to the PL band, and the magnetic Purcell effect in the PL-decay temporal measurement. This study experimentally demonstrates a new scheme of EM-LDOS engineering in plasmon-enhanced photonics, which will be a key technique to develop loss-compensated and active plasmonic devices.

The artificial control of enhanced optical processes in fluorescent molecules on high-emittance metasurfaces

Plasmon-enhanced optical processes in molecules have been extensively but individually explored for Raman scattering, fluorescence, and infrared light absorption. In contrast to recent progress in the interfacial control of hot electrons in plasmon-semiconductor hybrid systems, plasmon-molecule hybrid systems have remained to be a conventional scheme, mainly assuming electric-field enhancement. This was because it was difficult to control the plasmon-molecule interface in a well-controlled manner. We here experimentally substantiate an obvious change in artificially enhanced optical processes of fluorescence/Raman scattering in fluorescent molecules on high-emittance plasmo-photonic metasurfaces with/without a self-assembled monolayer of sub-nm thickness. These results indicate that the enhanced optical processes were successfully selected under artificial configurations without any additional chemical treatment that modifies the molecules themselves. Although Raman-scattering efficiency is generally weak in high-fluorescence-yield molecules, it was found that Raman scattering becomes prominent around the molecular fingerprint range on the metasurfaces, being enhanced by more than 2000 fold at the maximum for reference signals. In addition, the highly and uniformly enhancing metasurfaces are able to serve as two-way functional, reproducible, and wavelength-tunable platforms to detect molecules at very low densities, being distinct from other platforms reported so far. The change in the enhanced signals suggests that energy diagrams in fluorescent molecules are changed in the configuration that includes the metal-molecule interface, meaning that plasmon-molecule hybrid systems are rich in the phenomena beyond the conventional scheme.

Ultraviolet-nanoimprinted packaged metasurface thermal emitters for infrared CO2 sensing

Packaged dual-band metasurface thermal emitters integrated with a resistive membrane heater were manufactured by ultraviolet (UV) nanoimprint lithography followed by monolayer lift-off based on a soluble UV resist, which is mass-producible and cost-effective. The emitters were applied to infrared CO2 sensing. In this planar Au/Al2O3/Au metasurface emitter, orthogonal rectangular Au patches are arrayed alternately and exhibit nearly perfect blackbody emission at 4.26 and 3.95 μm necessary for CO2 monitoring at the electric power reduced by 31%. The results demonstrate that metasurface infrared thermal emitters are almost ready for commercialization.

Overcoming metal-induced fluorescence quenching on plasmo-photonic metasurfaces coated by a self-assembled monolayer

A schematic energy diagram of the present fluorescence (FL)-enhancing process including nonradiative (NR) paths that a self-assembled monolayer (SAM) blocks is presented.

Diffraction-unlimited optical imaging of unstained living cells in liquid by electron beam scanning of luminescent environmental cells

An environmental cell with a 50-nm-thick cathodoluminescent window was attached to a scanning electron microscope, and diffraction-unlimited near-field optical imaging of unstained living human lung epithelial cells in liquid was demonstrated. Electrons with energies as low as 0.8 - 1.2 kV are sufficiently blocked by the window without damaging the specimens, and form a sub-wavelength-sized illumination light source. A super-resolved optical image of the specimen adhered to the opposite window surface was acquired by a photomultiplier tube placed below. The cells after the observation were proved to stay alive. The image was formed by enhanced dipole radiation or energy transfer, and features as small as 62 nm were resolved.

Wavefront control by stacked metal-dielectric hole array with variable hole shapes

A stacked metal-dielectric hole array (SHA) containing rectangular holes whose shape gradually varies in-plane is proposed as a means of achieving wavefront control. The dependence of the transmitted phase on the frequency can be tuned by the hole shape, in particular the length of the sides that are normal to the incident polarization. The combination of periodic holes along the polarization direction and the gradual change in hole shape normal to the polarization direction produce an inclined wavefront for 1-dimensional beam steering. An in-plane phase difference of 0.6π using an SHA with a thickness of one-sixth of the wavelength has been experimentally demonstrated.

Transmission phase control by stacked metal-dielectric hole array with two-dimensional geometric design

Transmission phase control is experimentally demonstrated using stacked metal-dielectric hole arrays with a two-dimensional geometric design. The transmission phase varies drastically with small frequency shifts due to structural resonances. Laterally propagating surface plasmon polaritons excited by the periodic hole array roughly determine the resonance frequency, whereas localized resonances in each hole determine the dispersion. The transmission phase at various frequencies is directly evaluated using interferometric microscopy, and the formation of an inclined wavefront is demonstrated using a beam steering element in which the hole shapes gradually change in-plane from square to circular.

Cavity formation on an optical nanofiber using focused ion beam milling technique

We present the experimental realization of nanofiber Bragg grating (NFBG) by drilling periodic nano-grooves on a subwavelength-diameter silica fiber using focused ion beam milling technique. Using such NFBG structures we have realized nanofiber cavity systems. The typical finesse of such nanofiber cavity is F ∼ 20 - 120 and the on-resonance transmission is ∼ 30 - 80%. Moreover the structural symmetry of such NFBGs results in polarization-selective modes in the nanofiber cavity. Due to the strong confinement of the field in the guided mode, such a nanofiber cavity can become a promising workbench for cavity QED.

Graphical template software for accurate micromanipulation in a scanning electron microscope

Micromanipulation techniques in a scanning electron microscope (SEM) have been utilized for assembling micrometer-sized structures. The precision of the assembled microstructures has been limited by the poor accuracy of the SEM image. We have developed a software to assist the operator in the accurate assembly of microstructures in a SEM, in which computer-generated outlines of the target structure [graphical templates (GTs)] are superimposed on the monitor. The displayed GTs are distorted on the basis of the image properties of the SEM evaluated in advance. As a consequence, the operator can construct microstructures with a high precision only by maneuvering the manipulator so that the outline of each object perfectly overlaps the GT without any alteration of the electron optics or circuits for improving the image accuracy.

Light propagation from a fluorescent particle embedded in a photonic cluster of micrometer-sized dielectric spheres

In self-assembled multilayer arrays of micrometer-sized spheres that include small amounts of fluorescent particles, unique six-dot-triangular and seven-dot-hexagonal patterns have been known to appear in the fluorescence microscopic images. Although it has been suggested that these two types of patterns correspond to local domain structures, i.e., face centered cubic (fcc) or hexagonal closed packed (hcp), no conclusive evidence has been provided to support this claim. In this study, we systematically investigated the relationship between the propagation patterns and the arrangement of the particles. Through a cross-check between an experiment using well-defined clusters fabricated by a micromanipulation technique and a rigorous calculation based on the expansion of vector spherical harmonics, we confirmed that the six-dot-triangular and seven-dot-hexagonal patterns correspond to the fcc and hcp domains, respectively. Further, we also found that the propagation patterns depend on the size of the clusters. As a result of a quantitative discussion on the light propagation in clusters with various sizes, it was clarified that a sufficient domain size is necessary for the appearance of clear triangular or hexagonal patterns.

Inverse design for full control of spontaneous emission using light emitting scattering optical elements

Full control of spontaneous emission is essential in various fields of optics. This work presents an inverse designed light-emitting scattering optical element that includes full control of spontaneously emitted photons (i.e., enhancement at a central frequency and suppression at neighboring frequencies) and directionality of the output beam. This is achieved by embedding a one-dimensional optical active element inside a cluster of square shaped gallium arsenide dielectric rods whose positions are optimized by a genetic algorithm. Large spontaneous emission enhancement of > 70 is predicted at the transition wavelength if high-quality sources are employed. Moreover, neighboring wavelengths are simultaneously suppressed over 10 times. Finally, the radiated beam is highly collimated to only 6 degrees and contains 30 times the energy emitted by the source placed in free space.

Squeezing visible light waves into a 3-nm-thick and 55-nm-long plasmon cavity

We demonstrate controlled squeezing of visible light waves into nanometer-sized optical cavities. The light is perpendicularly confined in a few-nanometer-thick SiO2 film sandwiched between Au claddings in the form of surface plasmon polaritons and exhibits Fabry-Perot resonances in a longitudinal direction. As the thickness of the dielectric core is reduced, the plasmon wavelength becomes shorter; then a smaller cavity is realized. A dispersion relation down to a surface plasmon wavelength of 51 nm for a red light, which is less than 8% of the free-space wavelength, was experimentally observed. Any obvious breakdowns of the macroscopic electromagnetics based on continuous dielectric media were not disclosed for 3-nm-thick cores.

Analysis of specular resonance in dielectric bispheres using rigorous and geometrical-optics theories

We have recently identified the resonant scattering from dielectric bispheres in the specular direction, which has long been known as the specular resonance, to be a type of rainbow (a caustic) and a general phenomenon for bispheres. We discuss the details of the specular resonance on the basis of systematic calculations. In addition to the rigorous theory, which precisely describes the scattering even in the resonance regime, the ray-tracing method, which gives the scattering in the geometrical-optics limit, is used. Specular resonance is explicitly defined as strong scattering in the direction of the specular reflection from the symmetrical axis of the bisphere whose intensity exceeds that of the scattering from noninteracting bispheres. Then the range of parameters for computing a particular specular resonance is specified. This resonance becomes prominent in a wide range of refractive indices (from 1.2 to 2.2) in a wide range of size parameters (from five to infinity) and for an arbitrarily polarized light incident within an angle of 40 degrees to the symmetrical axis. This particular scattering can stay evident even when the spheres are not in contact or the sizes of the spheres are different. Thus specular resonance is a common and robust phenomenon in dielectric bispheres. Furthermore, we demonstrate that various characteristic features in the scattering from bispheres can be explained successfully by using intuitive and simple representations. Most of the significant scatterings other than the specular resonance are also understandable as caustics in geometrical-optics theory. The specular resonance becomes striking at the smallest size parameter among these caustics because its optical trajectory is composed of only the refractions at the surfaces and has an exceptionally large intensity. However, some characteristics are not accounted for by geometrical optics. In particular, the oscillatory behaviors of their scattering intensity are well described by simple two-wave interference models.

Microassembly of semiconductor three-dimensional photonic crystals

Electronic devices and their highly integrated components formed from semiconductor crystals contain complex three-dimensional (3D) arrangements of elements and wiring. Photonic crystals, being analogous to semiconductor crystals, are expected to require a 3D structure to form successful optoelectronic devices. Here, we report a novel fabrication technology for a semiconductor 3D photonic crystal by uniting integrated circuit processing technology with micromanipulation. Four- to twenty-layered (five periods) crystals, including one with a controlled defect, for infrared wavelengths of 3-4.5 microm, were integrated at predetermined positions on a chip (structural error <50 nm). Numerical calculations revealed that a transmission peak observed at the upper frequency edge of the bandgap originated from the excitation of a resonant guided mode in the defective layers. Despite their importance, detailed discussions on the defective modes of 3D photonic crystals for such short wavelengths have not been reported before. This technology offers great potential for the production of optical wavelength photonic crystal devices.

Anomalous scattering from dielectric bispheres in the specular direction

Resonant scattering from dielectric bispheres in the specular direction (the so-called specular resonance), previously known only in the microwave range, has been observed at the optical wavelength. Systematic experiments with micrometer-sized dielectric bispheres assembled by micromanipulation, together with rigorous numerical calculations, reveal that this scattering is a precursor of the classical rainbow and is a general phenomenon observed in the wide range of size parameters (>5 for n=1.59) for various refractive indices.

Micro-object Pick and Place Operation under SEM based on Micro-physics

Recently, techniques of arranging micrometer-sized objects under a scanning electron microscope (SEM) are required to construct micro-devices such as quantum optics devices. Since micro-objects tend to adhere to other objects mainly by electrostatic force, it is possible to pick them easily with a needle-tip instead of grasping by a gripper. However, it is difficult to place them on a substrate precisely, and furthermore even picking them is not achieved with enough reliability. To solve this problem, in this study, basic strategy for pick and place operation is indicated based on the actual measurement of adhesion under SEM first. Secondly dynamics for pick and place operation of a microsphere by a needle-shaped tool is analyzed. Thirdly a new method of practical pick and place is proposed on the basis of the basic strategy and the dynamics. Experimental system for executing the proposed operation is constructed based on the numeric-control of the position measurement of the target object. On this system, a lot of numeric-controlled experiments with 2µm polystyrene spheres reveal that under the optimal conditions, pick operation has never failed once out of over 20 trials and place operation has 140nm precision in position. From these results, this paper concludes that the proposed method can realize practical pick operation and place operation under SEM based on micro-physics.