Micro-CT Imaging and Mechanical Properties of Ovine Ribs

The use of ovine animal models in the study of injury biomechanics and modeling is increasing, due to their favorable size and other physiological characteristics. Along with this increase, there has also been increased interest in the development of in silico ovine models for computational studies to compliment physical experiments. However, there remains a gap in the literature characterizing the morphological and mechanical characteristics of ovine ribs. The objective of this study therefore is to report anatomical and mechanical properties of the ovine ribs using microtomography (micro-CT) and two types of mechanical testing (quasi-static bending and dynamic tension). Using microtomography, young ovine rib samples obtained from a local abattoir were cut into approximately fourteen 38 mm sections and scanned. From these scans, the cortical bone thickness and cross-sectional area were measured, and the moment of inertia was calculated to enhance the mechanical testing data. Based on a standard least squares statistical model, the cortical bone thickness varied depending on the region of the cross-section and the position along the length of the rib (p < 0.05), whereas the cross-sectional area remained consistent (p > 0.05). Quasi-static three-point bend testing was completed on ovine rib samples, and the resulting force-displacement data was analyzed to obtain the stiffness (44.67 ± 17.65 N/mm), maximum load (170.54 ± 48.28 N) and displacement at maximum load (7.19 ± 2.75 mm), yield load (167.81 ± 48.12 N) and displacement at yield (6.10 ± 2.25 mm), and the failure load (110.90 ± 39.30 N) and displacement at failure (18.43 ± 2.10 mm). The resulting properties were not significantly affected by the rib (p > 0.05), but by the animal they originated from (p < 0.05). For the dynamic testing, samples were cut into coupons and tested in tension with an average strain rate of 18.9 strain/sec. The resulting dynamic testing properties of elastic modulus (5.16 ± 2.03 GPa), failure stress (63.29 ± 14.02 MPa), and failure strain (0.0201 ± 0.0052) did not vary based on loading rate (p > 0.05).

Lower Extremity Validation of a Human Body Model for High Rate Axial Loading in the Underbody Blast Environment

While the use of Human Body Models (HBMs) in the underbody blast (UBB) environment has increased and shown positive results, the potential of these models has not been fully explored. Obtaining accurate kinematic and kinetic response are necessary to better understand the injury mechanisms for military safety applications. The objective of this study was to validate the Global Human Body Models Consortium (GHBMC) M50 lower extremity using a combined objective rating scheme in vertical and horizontal high-rate axial loading. The model's lower extremity biomechanical response was compared to Post Mortem Human Subjects (PMHS) subjects for vertically and horizontally-applied high rate axial loading. Two distinct experimental setups were used for model validation, comprising a total of 33 distinct end points for validation. A combined Correlation and Analysis (CORA) score that incorporates CORA, time-to-peak (TTP) and peak magnitude of the experimental signals and ISO TS 18571 was used to evaluate the model response. For the horizontal impacts, the combined CORA scores were 0.80, 0.84, and 0.81 for compression, force, and strain respectively. For the vertical impacts combined CORA scores for the knee Z force, compression and heel Z displacement ranged from 0.70-0.81, 0.87-0.91, and 0.82-0.99 respectively. The GHBMC lower extremity model showed good agreement with PMHS experimental data in the horizontal and vertical loading environment in 33 unique tests. The accuracy is demonstrated by using the ISO TS 18571 standard and a combined CORA score that takes into consideration the peak and time to peak of the signal. The results of this study show that GHBMC v 6.0 HBM lower extremity can be used for kinetic and kinematic predictions in the UBB environment.

Trophic flexibility and opportunism in pike Esox lucius

The first comprehensive investigation of pike Esox lucius trophic ecology in a region (Ireland) where they have long been thought to be a non-native species is presented. Diet was investigated across habitat types (lake, river and canal) through the combined methods of stable-isotope and stomach content analyses. Variations in niche size, specialization and the timing of the ontogenetic dietary switch were examined, revealing pronounced opportunism and feeding plasticity in E. lucius, along with a high occurrence of invertivory (up to 60 cm fork length, LF ) and a concomitant delayed switch to piscivory. Furthermore, E. lucius were found to primarily prey upon the highly available non-native roach Rutilus rutilus, which may alleviate predation pressure on brown trout Salmo trutta, highlighting the complexity of dynamic systems and the essential role of research in informing effective management.

Trophic flexibility by roach Rutilus rutilus in novel habitats facilitates rapid growth and invasion success

Stable isotope and gut content analyses, in conjunction with backcalculated length-at-age estimates of growth, were employed to examine the relationship between trophic ecology and growth rate of a successful invader, Rutilus rutilus, in eight lakes in Ireland. The data revealed that R. rutilus was a trophic generalist in Irish lakes. It utilized a greater proportion of pelagic resources in mesotrophic lakes than in eutrophic lakes, potentially due to a greater density of benthic macroinvertebrates in eutrophic systems. The species was characterized by a large dietary and isotopic niche width and high temporal and spatial variations in diet. Growth rates were typical of those found in the native range of the species and were unrelated to either lake productivity or fish's diet. A generalist trophic ecology confers significant advantages on an invasive species, allowing it to exploit a variety of novel resources and fluctuations in prey availability.