Passive performance evaluation and validation of a viscous impeller pump for subpulmonary fontan circulatory support

Patients with single ventricle defects undergoing the Fontan procedure eventually face Fontan failure. Long-term cavopulmonary assist devices using rotary pump technologies are currently being developed as a subpulmonary power source to prevent and treat Fontan failure. Low hydraulic resistance is a critical safety requirement in the event of pump failure (0 RPM) as a modest 2 mmHg cavopulmonary pressure drop can compromise patient hemodynamics. The goal of this study is therefore to assess the passive performance of a viscous impeller pump (VIP) we are developing for Fontan patients, and validate flow simulations against in-vitro data. Two different blade heights (1.09 mm vs 1.62 mm) and a blank housing model were tested using a mock circulatory loop (MCL) with cardiac output ranging from 3 to 11 L/min. Three-dimensional flow simulations were performed and compared against MCL data. In-silico and MCL results demonstrated a pressure drop of < 2 mmHg at a cardiac output of 7 L/min for both blade heights. There was good agreement between simulation and MCL results for pressure loss (mean difference - 0.23 mmHg 95% CI [0.24-0.71]). Compared to the blank housing model, low wall shear stress area and oscillatory shear index on the pump surface were low, and mean washout times were within 2 s. This study demonstrated the low resistance characteristic of current VIP designs in the failed condition that results in clinically acceptable minimal pressure loss without increased washout time as compared to a blank housing model under normal cardiac output in Fontan patients.

Passive Performance Evaluation and Validation of a Viscous Impeller Pump for Subpulmonary Fontan Circulatory Support

Patients with single ventricle defects undergoing the Fontan procedure eventually face Fontan failure. Long-term cavopulmonary assist devices using rotary pump technologies are currently being developed as a subpulmonary power source to prevent and treat Fontan failure. Low hydraulic resistance is a critical safety requirement in the event of pump failure (0 RPM) as a modest 2 mmHg cavopulmonary pressure drop can compromise patient hemodynamics. The goal of this study is therefore to assess the passive performance for a viscous impeller pump (VIP) we are developing for Fontan patients, and validate flow simulations against in-vitro data. Two different blade heights (1.09 mm vs 1.62 mm) and a blank housing model were tested using a mock circulatory loop (MCL) with cardiac output ranging from 3 to 11 L/min. Three-dimensional flow simulations were performed and compared against MCL data. In-silico and MCL results demonstrated a clinically insignificant pressure drop of $<$ 2 mmHg at a cardiac output of 7 L/min for both blade heights. There was good agreement between simulation and MCL results for pressure loss (mean difference -0.23 mmHg 95% CI [0.24 -0.71]). Compared to the blank housing model, low wall shear stress area and oscillatory shear index on the pump surface were low, and mean washout times were within 2 seconds. This study demonstrated the low resistance characteristic of current VIP designs in the failed condition that results in clinically acceptable minimal pressure loss with low risk of thrombosis.

Patient-Specific Multiscale Modeling of the Assisted Bidirectional Glenn

BACKGROUND

First-stage palliation of neonates with single-ventricle physiology is associated with poor outcomes and challenging clinical management. Prior computational modeling and in vitro experiments introduced the assisted bidirectional Glenn (ABG), which increased pulmonary flow and oxygenation over the bidirectional Glenn (BDG) and the systemic-to-pulmonary shunt in idealized models. In this study, we demonstrate that the ABG achieves similar performance in patient-specific models and assess the influence of varying shunt geometry.

METHODS

In a small cohort of single-ventricle prestage 2 patients, we constructed three-dimensional in silico models and tuned lumped parameter networks to match clinical measurements. Each model was modified to produce virtual BDG and ABG surgeries. We simulated the hemodynamics of the stage 1 procedure, BDG, and ABG by using multiscale computational modeling, coupling a finite-element flow solver to the lumped parameter network. Two levels of pulmonary vascular resistances (PVRs) were investigated: baseline (low) PVR of the patients and doubled (high) PVR. The shunt nozzle diameter, anastomosis location, and shape were also manipulated.

RESULTS

The ABG increased the pulmonary flow rate and pressure by 15% to 20%, which was accompanied by a rise in superior vena caval pressure (2 to 3 mm Hg) at both PVR values. Pulmonary flow rate and superior vena caval pressures were most sensitive to the shunt nozzle diameter.

CONCLUSIONS

Patient-specific ABG performance was similar to prior idealized simulations and experiments, with good performance at lower PVR values in the range of measured clinical data. Larger shunt outlet diameters and lower PVR led to improved ABG performance.

In Vitro Assessment of the Assisted Bidirectional Glenn Procedure for Stage One Single Ventricle Repair

This in vitro study compares the hemodynamic performance of the Norwood and the Glenn circulations to assess the performance of a novel assisted bidirectional Glenn (ABG) procedure for stage one single ventricle surgery. In the ABG, the flow in a bidirectional Glenn procedure is assisted by injection of a high-energy flow stream from the systemic circulation using an aorta-caval shunt with nozzle. The aim is to explore experimentally the potential of the ABG as a surgical alternative to current surgical practice. The experiments are directly compared against previously published numerical simulations. A multiscale mock circulatory system was used to measure the hemodynamic performance of the three circulations. For each circulation, the system was tested using both low and high values of pulmonary vascular resistance. Resulting parameters measured were: pressure and flow rate at left/right pulmonary artery and superior vena cava (SVC). Systemic oxygen delivery (OD) was calculated. A parametric study of the ratio of ABG nozzle to shunt diameter was done. We report time-based comparisons with numerical simulations for the three surgical variants tested. The ABG circulation demonstrated an increase of 30-38% in pulmonary flow with a 2-3.7 mmHg increase in SVC pressure compared to the Glenn and a 4-14% higher systemic OD than either the Norwood or the Glenn. The nozzle/shunt diameter ratio affected the local hemodynamics. These experimental results agreed with those of the numerical model: mean flow values were not significantly different (p > 0.05) while mean pressures were comparable within 1.2 mmHg. The results verify the approaches providing two tools to study this complicated circulation. Using a realistic experimental model we demonstrate the performance of a novel surgical procedure with potential to improve patient hemodynamics in early palliation of the univentricular circulation.

In vitro study of the Norwood palliation: a patient-specific mock circulatory system

The aim of this study was to build a mock circulatory system replicating in vitro the hemodynamics following the Norwood procedure and testing patient-specific anatomies focusing on the effect of aortic coarctation. Three anatomies were reconstructed from magnetic resonance images and rapid prototyped with transparent rigid resin. The models presented varying degrees of coarctation (none, moderate, and severe). A Blalock-Taussing (BT) shunt was modeled in all phantoms, which were inserted into a mock circulation. The single ventricle was simulated using a Berlin Heart driven with a PC-controlled piston. Resistive and compliant elements were implemented, creating a lumped parameter network. Pressure was measured at three locations: the transverse aortic arch, just after the aortic isthmus, and further downstream in the thoracic aorta. Volume distribution was derived from the instantaneous flow measurements at three outlets: upper body, lower body, and BT shunt. The combination of three-dimensional (3D) detailed anatomy and lumped parameter network effectively renders the circuit a multiscale in vitro model that successfully reproduces physiologic pressure signals. The pressure results highlight the larger pressure drop caused by coarctation and show the effect of pressure recovery. Results also suggest a reduction of flow to the lower body with increasing severity of coarctation, to the advantage of upper body and pulmonary circulation.

In Vitro Simulation and Validation of the Circulation with Congenital Heart Defects

Despite the recent advances in computational modeling, experimental simulation of the circulation with congenital heart defect using mock flow circuits remains an important tool for device testing, and for detailing the probable flow consequences resulting from surgical and interventional corrections. Validated mock circuits can be applied to qualify the results from novel computational models. New mathematical tools, coupled with advanced clinical imaging methods, allow for improved assessment of experimental circuit performance relative to human function, as well as the potential for patient-specific adaptation. In this review, we address the development of three in vitro mock circuits specific for studies of congenital heart defects. Performance of an in vitro right heart circulation circuit through a series of verification and validation exercises is described, including correlations with animal studies, and quantifying the effects of circuit inertiance on test results. We present our experience in the design of mock circuits suitable for investigations of the characteristics of the Fontan circulation. We use one such mock circuit to evaluate the accuracy of Doppler predictions in the presence of aortic coarctation.

In vitro study of flow regulation for pulmonary insufficiency

Given the tolerance of the right heart circulation to mild regurgitation and gradient, we study the potential of using motionless devices to regulate the pulmonary circulation. In addition, we document the flow performance of two mechanical valves. A motionless diode, a nozzle, a mechanical bileaflet valve, and a tilting disk valve were tested in a pulmonary mock circulatory system over the normal human range of pulmonary vascular resistance (PVR). For the mechanical valves, regurgitant fractions (RFs) and transvalvular pressure gradients were found to be weak functions of PVR. On the low end of normal PVR, the bileaflet and tilting disk valves fluttered and would not fully close. Despite this anomaly, the regurgitant fraction of either valve did not change significantly. The values for RF and transvalvular gradient measured varied from 4 to 7% and 4 to 7 mm Hg, respectively, at 5 lpm for all tests. The diode valve was able to regulate flow with mild regurgitant fraction and trivial gradient but with values higher than either mechanical valve tested. Regurgitant fraction ranged from 2 to 17% in tests extending from PVR values of 1 to 4.5 mm Hg/lpm at 5 lpm and with concomitant increases in gradient up to 17 mm Hg. The regurgitant fraction for the nozzle increased from 2 to 23% over the range of PVR with gradients increasing to 18 mm Hg. The significant findings were: (1) the mechanical valves controlled regurgitation at normal physiological cardiac output and PVR even though they failed to close at some normal values of PVR and showed leaflet flutter; and (2) it may be possible to regulate the pulmonary circulation to tolerable levels using a motionless pulmonary valve device.

On the hemolytic and thrombogenic potential of occluder prosthetic heart valves from in-vitro measurements

An experimental investigation was conducted to determine the magnitude of shear stresses and areas of stasis of several types of prosthetic occluder heart valves. These experiments were performed in a steady-flow test loop using an axisymmetric aortic-shaped test chamber and an aqueous-glycerine solution. The flow loop produced a low-turbulence intensity and uniform mean velocity profile upstream of the test chamber. Tests were performed on a Kay-Shiley disk, a Bjork-Shiley tilting disk and Starr-Edwards Models 1260 and 2320 ball prostheses at Reynolds numbers between 2000 and 6200. Momentum transfer and turbulence data were obtained both around and distal to the valve occluders using laser Doppler and hot-film anemometry. The region directly surrounding the valve occluders contained the largest stresses measured. Aortic wall shear measurements revealed magnitudes potentially damaging to the vessel lining. Regions of slowly moving separated flow found to exist in these occluder valve flow fields correlated with clinical findings of thrombus formation.