Comparison of microstructure, mechanical property, and degradation rate of Mg-1Li-1Ca and Mg-4Li-1Ca alloys

Mg-1 wt.% Li-1 wt.% Ca (LX11) and Mg-4 wt.% Li-1 wt.% Ca (LX41) alloys share the same hexagonal closed-packed crystalline structure. However, the differences in microstructure, mechanical properties, and degradation rates between the two alloys are not well understood. Hereby, the above three aspects of LX11 and LX41 alloys were studied via optical microscopy, tensile tests, and electrochemical polarization and electrochemical impedance spectroscopy, together with hydrogen evolution. The concentration of the released Mg²⁺, Ca²⁺, and Li⁺ ions was analyzed using a flame atomic absorption spectrophotometer. Results demonstrated that the LX11 alloy was composed of finer α-Mg grains, fewer twins, and smaller volume fractions of the intermetallic phases Mg₂Ca than the LX41 alloy. The increasing Li concentration generated a weak decrease in the yield strength of the Mg-Li-Ca alloys, a remarkable increase in elongation to failure, and a stable ultimate tensile strength. The LX11 alloy had better corrosion resistance than the LX41 alloy. The release rate of the cations (Mg²⁺, Ca²⁺, and Li⁺) varied significantly with time. The release rate of metallic ions in Hank's solution cannot reflect the true corrosion rate of Mg-Li-Ca alloys due to the formation of the precipitated corrosion products and their difference in solubility. The dealloying corrosion mechanism of the Mg₂Ca phase in Mg-Li-Ca alloys was proposed.

In vitro corrosion resistance and dual antibacterial ability of curcumin loaded composite coatings on AZ31 alloy: Effect of amorphous calcium carbonate

Rapid corrosion and bacterial infection are obstacles to put into use biodegradable magnesium (Mg) alloy as biomedical materials. In this research, an amorphous calcium carbonate (ACC)@curcumin (Cur) loaded poly-methyltrimethoxysilane (PMTMS) coating prepared by self-assembly method on micro-arc oxidation (MAO) coated Mg alloy has been proposed. Scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy are adopted to analyze the morphology and composition of the obtained coatings. The corrosion behaviour of the coatings is estimated by hydrogen evolution and electrochemical tests. The spread plate method without or with 808 nm near-infrared irradiation is applied to evaluate the antimicrobial and photothermal antimicrobial ability of the coatings. Cytotoxicity of the samples is tested by 3-(4,5)-dimethylthiahiazo(-z-y1)-2,5-di- phenytetrazoliumromide (MTT) and live/dead assay culturing with MC3T3-E1 cells. Results show that the MAO/ACC@Cur-PMTMS coating exhibited favourable corrosion resistance, dual antibacterial ability, and good biocompatibility. Cur was employed as an antibacterial agent and photosensitizer for photothermal therapy. The core of ACC significantly improved the loading of Cur and the deposition of hydroxyapatite corrosion products during degradation, which greatly promoted the long-term corrosion resistance and antibacterial activity of Mg alloys as biomedical materials.

Corrosion self-warning and repair tracking of polymeric coatings based on stimulus responsive nanosensors

Smart polymeric coatings with early corrosion self-warning and damage self-repairing characteristics have garnered tremendous interest due to their ability to sense corrosion reactions and repair coating defects. However, tracking the repair process and its underlying protection mechanism is highly challenging. Herein, we report the construction of a novel composite coating by incorporating multifunctional nanosensors (graphene oxide-zeolitic imidazole frameworks loaded with 1,10-phenanthroline) into a thermo-responsive polyurethane. Under damaging events, the localized acidity derived from metal corrosion stimulates the decomposition of the nanosensors to produce 1,10-phenanthroline and benzimidazole. The generated ferrous ions are rapidly sensed by the released 1,10-phenanthroline to produce a conspicuous red color, which warns of the corrosion occurrence. In profiting from the photothermal effect of graphene oxide, the composite coating exhibits efficient crack closure behavior under near-infrared light irradiation. Morphology observation indicates that a coating scratch (about 30 μm wide) almost closed with 20 s of irradiation. The photothermally activated crack closure combined with benzimidazole inhibition endows the prepared coating with superior self-repairing performance. Interestingly, the change in color intensity around the coating defect can assist in tracking the repair process. Therefore, this work provides a novel strategy to visualize microscopic behaviors during damage and repair processes.

Advances in coatings on magnesium alloys for cardiovascular stents - A review

Magnesium (Mg) and its alloys, as potential biodegradable materials, have drawn wide attention in the cardiovascular stent field because of their appropriate mechanical properties and biocompatibility. Nevertheless, the occurrence of thrombosis, inflammation, and restenosis of implanted Mg alloy stents caused by their poor corrosion resistance and insufficient endothelialization restrains their anticipated clinical applications. Numerous surface treatment tactics have mainly striven to modify the Mg alloy for inhibiting its degradation rate and enduing it with biological functionality. This review focuses on highlighting and summarizing the latest research progress in functionalized coatings on Mg alloys for cardiovascular stents over the last decade, regarding preparation strategies for metal oxide, metal hydroxide, inorganic nonmetallic, polymer, and their composite coatings; and the performance of these strategies in regulating degradation behavior and biofunction. Potential research direction is also concisely discussed to help guide biological functionalized strategies and inspire further innovations. It is hoped that this review can give assistance to the surface modification of cardiovascular Mg-based stents and promote future advancements in this emerging research field.

[Seasonal Variations in Nitrogen and Phosphorus Concentration and Stoichiometry of Hanfeng Lake in the Three Gorges Reservoir Area]

Based on the seasonal changes in the nitrogen and phosphorus concentrations in Hanfeng Lake from March 2017 to February 2018, the nutrient limitation status was evaluated by the stoichiometric molar ratio of nitrogen and phosphorus. The results showed that the average concentrations of TN, DN, and NO₃^--N were 1.60, 1.25, and 0.91 mg·L^-1 in Hanfeng Lake, respectively. The seasonal changes of those indicators were similar, showing the highest concentration in winter and lowest in summer. NO₃^--N accounted for TN significantly in the water body, and the concentrations of NH₄⁺-N and NO₂^--N remained at low levels and changed steadily. The average concentrations of TP, DP, and PO₄^3--P were 0.13, 0.09, and 0.06 mg·L^-1, respectively. The changes in the concentrations of TP and DP were similar, showing a trend of increasing in spring and summer, and then decreasing in autumn and winter, while the PO₄^3--P concentration showed the trend of fluctuated decrease. TN/TP varied from 11.07 to 56.02, with an average value of 29.23. TN/TP changed seasonally, with the highest value occurring in winter and the lowest value in summer. The conditions of the water body were conducive to growth and reproduction of algae for most of the time during sampling months. The water body was occasionally nitrogen limited and rarely phosphorus limited. The seasonal variation in TN/TP ratio was affected by several factors such as rainfall runoff, fertilizer use, sewage discharge, and aquatic biological activities. Further, protection strategies were proposed for the improvement of the water body in terms of present water quality characteristics in Hanfeng Lake.

Microbial ingress and in vitro degradation enhanced by glucose on bioabsorbable Mg-Li-Ca alloy

Biodegradable magnesium alloys are challenging to be implanted in patients with hyperglycemia and diabetes. A hypothesis is suggested that glucose accelerates microbial ingress and in vitro degradation of Mg-Li-Ca implants. Corrosion resistance and mechanical properties was demonstrated using electrochemical, hydrogen evolution and tensile tests. The bacteria from Hank's solution were isolated via 16S rRNA gene analysis. The results revealed that Mg-1Li-1Ca alloy exhibited different responses to Hank's solution with and without glucose. The solution acidity was ascribed to Microbacterium hominis and Enterobacter xiangfangensis, indicating that glucose promoted microbial activity and degradation and deterioration in mechanical property of Mg-1Li-1Ca alloy.

In vitro degradation and cytocompatibility of a low temperature in-situ grown self-healing Mg-Al LDH coating on MAO-coated magnesium alloy AZ31

Basically, Mg-Al layered double hydroxide (LDH) coatings are prepared on the surface of micro-arc oxidation (MAO) coated magnesium (Mg) alloys at a high temperature or a low pH value. This scenario leads to the growth rate of LDH coating inferior to the dissolution rate of the MAO coating. This in turn results in limited corrosion resistance of the composite coating. In this study, a Mg-Al LDH coating on MAO-coated Mg alloy AZ31 is prepared through a water bath with a higher pH (13.76) at a lower temperature (60 °C). FE-SEM, EDS, XRD, XPS, and FT-IR are applied to analyze the surface morphology, chemical compositions, and growth process. Electrochemical polarization, electrochemical impedance spectroscopy (EIS) and hydrogen evolution tests are employed to evaluate the corrosion resistance of the samples. The results disclose that the MAO coating is completely covered by the nanosheet-structured LDH coating with a thickness of approximately 3.8 μm. The corrosion current density of the MAO-LDH composite coating is decreased four orders of magnitude in comparison to its substrate; the presence of a wide passivation region in anodic polarization branch demonstrates its strong self-healing ability, indicating the hybrid coating possesses excellent corrosion resistance. The formation mechanism of the LDH coating on the MAO-coated Mg alloy is proposed. Furthermore, the cytocompatibility is assessed via an indirect extraction test for MC3T3-E1 pre-osteoblasts, which indicates an acceptable cytocompatibility of osteoblasts for the composite coating.

In vitro degradation of pure magnesium-the synergetic influences of glucose and albumin

The biocorrosion of magnesium in the external physiological environment is still difficult to accurately evaluate the degradation behavior in vivo, particularly, in the microenvironment of the patients with hyperglycemia or diabetes. Thus, we explored the synergistic effects of glucose and protein on the biodegradation of pure magnesium, so as to have a deeper understanding the mechanism of the degradation in vivo. The surface morphology and corrosion product composition of pure magnesium were investigated using SEM, EDS, FTIR, XRD and XPS. The effect of glucose and albumin on the degradation rate of pure magnesium was investigated via electrochemical and immersion tests. The adsorption of glucose and albumin on the sample surface was observed using fluorescence microscopy. The results showed that the presence of 2 g/L glucose changed the micromorphology of corrosion products on the magnesium surface by reacting with metal cations, thus inhibiting the corrosion of pure magnesium. Protein formed a barrier layer to protect the magnesium at early stage of immersion. The chelation reaction between protein and magnesium surface might accelerate the degradation at later stage. There may be a critical glucose (albumin) content. Biodegradation of pure magnesium was inhibited at low concentrations and promoted at high concentrations. The synergistic effect of glucose and protein restrained the adsorption of aggressive chloride ions to a certain extent, and thus inhibited the degradation of pure magnesium considerably. Moreover, XPS results indicated that glucose promoted the adsorption of protein on the sample surface.

In vitro corrosion resistance of a Ta2O5 nanofilm on MAO coated magnesium alloy AZ31 by atomic layer deposition

Micro-arc oxidation (MAO) coating with outstanding adhesion strength to Mg alloys has attracted more and more attention. However, owing to the porous structure, aggressive ions easily invaded the MAO/substrate interface through the through pores, limiting long-term corrosion resistance. Therefore, a dense and biocompatible tantalum oxide (Ta2O5) nanofilm was deposited on MAO coated Mg alloy AZ31 through atomic layer deposition (ALD) technique to seal the micropores and regulate the degradation rate. Surface micrography, chemical compositions and crystallographic structure were characterized using FE-SEM, EDS, XPS and XRD. The corrosion resistance of all samples was evaluated through electrochemical and hydrogen evolution tests. Results revealed that the Ta2O5 film mainly existed in the form of amorphousness. Moreover, uniform deposition of Ta2O5 film and effective sealing of micropores and microcracks in MAO coating were achieved. The current density (i corr) of the composite coating decreased three orders of magnitude than that of the substrate and MAO coating, improving corrosion resistance. Besides, the formation and corrosion resistance mechanisms of the composite coating were proposed.

In vitro corrosion resistance of layer-by-layer assembled polyacrylic acid multilayers induced Ca-P coating on magnesium alloy AZ31

Biodegradable magnesium (Mg)-based alloys have aroused great concern owing to their promising characteristics as temporary implants for orthopedic application. But their undesirably rapid corrosion rate under physiological conditions has limited the actual clinical application. This study reports the use of a novel biomimetic polyelectrolyte multilayer template, based on polyvinylpyrrolidone (PVP) and polyacrylic acid (PAA) via layer-by-layer (LbL) assembly, to improve the corrosion resistance of the alloy. Surface characterization techniques (field-emission scanning electron microscopy, Fourier transform infrared (FTIR) spectrophotometer and X-ray diffractometer) confirmed the formation of biomineralized Ca-P coating on AZ31 alloy. Both hydrogen evolution and electrochemical corrosion tests demonstrated that the corrosion protection of the polyelectrolyte-induced Ca-P coating on AZ31 alloy. The formation mechanism of biomineralized Ca-P coating was proposed.

In vitro corrosion of pure Mg in phosphate buffer solution-Influences of isoelectric point and molecular structure of amino acids

Influences of proteins on degradation of magnesium alloys are of great significance but not well understood. In particular the roles of amino acids, the basic unit of proteins in regulating the progress of biodegradation of magnesium based materials remain unclear. This study aims to investigate the impacts of alanine, glutamic acid and lysine on degradation of pure magnesium in phosphate buffer solution through SEM, XPS, FTIR, potentiodynamic polarisation curves, electrochemical impedance spectroscopy and immersion tests. The changed contents of amino acids in solutions were detected by UV-vis spectrophotometer. Results demonstrate that the charges of the selected amino acids imposed significant contribution to suppressing the degradation of pure magnesium in phosphate buffer solution. The presence of amino acids led to the formation of phosphate-based corrosion products, increasing free corrosion potential, and reduction in corrosion current density and solution pH depending on their isoelectric points and molecular structures. A plausible corrosion mechanism organised by amino acids on pure magnesium was proposed.

Corrosion resistance and antibacterial properties of hydroxyapatite coating induced by gentamicin-loaded polymeric multilayers on magnesium alloys

As a result of their good biocompatibility, bioactivity, and mechanical properties, magnesium (Mg) alloys have received considerable attention as next generation biodegradable implants. Herein, in order to achieve a proper degradation rate and good antibacterial ability, we reported a novel hydroxyapatite coating induced by gentamicin (GS)-loaded polymeric multilayers for the surface treatment of the Mg alloy. The coating was characterized by X-ray diffraction, fourier transform infrared spectroscopy and scanning electron microscopy. The as-prepared hydroxyapatite coating showed the compact morphology and a well-crystallized apatite structure. This coating could improve the adhesion strength and reduce the corrosion rate of the substrate in simulated body fluid solution. Meanwhile, the drug release and antibacterial experiments demonstrated that the GS loaded specimen revealed a significant antimicrobial performance toward Staphylococcus aureus and had a prolonged release profile of GS, which would be helpful to the long-term bactericidal activity of the Mg implant. This coating showed acceptable biocompatibility via MTT assay and Live/dead staining. Thus, the multilayers-hydroxyapatite coated Mg alloy could improve the corrosion resistance and biocompatibility while delivering vital drugs to the site of implantation.

Advances in functionalized polymer coatings on biodegradable magnesium alloys - A review

Magnesium (Mg) and its alloys have become a research frontier in biodegradable materials owing to their superior biocompatibility and excellent biomechanical compatibility. However, their high degradation rate in the physiological environment should be well tackled prior to clinical applications. This review summarizes the latest progress in the development of polymeric coatings on biodegradable Mg alloys over the last decade, regarding preparation strategies for polylactic acid (PLA), poly (latic-co-glycolic) acid (PLGA), polycaprolactone (PCL), polydopamine (PDA), chitosan (CS), collagen (Col) and their composite, and their performance in terms of corrosion resistance and biocompatibility. Feasible perspectives and developing directions of next generation of polymeric coatings with respect to biomedical Mg alloys are briefly discussed.

STATEMENT OF SIGNIFICANCE

Magnesium (Mg) and its alloys have become a research frontier in biodegradable materials owing to their superior biocompatibility and suitable biomechanical compatibility. However, the principal drawback of Mg-based implants is their poor corrosion resistance in physiological environments. Hence, it is vital to mitigate the degradation/corrosion behavior of Mg alloys for safe biomedical deployments. This review summarizes the latest progress in development of polymeric coatings on biomedical Mg alloys regarding preparation strategy, corrosion resistance and biocompatibility, including polylactic acid (PLA), poly (latic-co-glycolic) acid (PLGA), polycaprolactone (PCL), chitosan (CS), polydopamine (PDA), collagen (Col) and their composite. In addition, functionalized polymer coatings with Mg alloys exhibits a promising prospect owing to their ability of degradation along with biocompatibility, self-healing, drug-delivery and osteoinduction.

Corrosion resistance of a novel SnO2-doped dicalcium phosphate coating on AZ31 magnesium alloy

A SnO₂-doped dicalcium phosphate coating was prepared on AZ31 alloy by means of hydrothermal deposition. The results showed that the coating possessed a globular morphology with a long lamellar crystalline structure and a thickness of approximately 40 μm. The surface of the coating became smooth with an increase additive amount of the SnO₂ nanoparticles. The corrosion current density and hydrogen evolution rate of the coating prepared in presence of SnO₂ were reduced compared to the coating without SnO₂ and the bare AZ31 substrate, indicating an improvement in the corrosion resistance of the SnO₂-doped coating.

•

A thick and dense SnO₂-doped DCPA coating forms via hydrothermal deposition.

•

The DCPA coating doped with 10 g L⁻¹ SnO₂ exhibits the best corrosion resistance.

•

SnO₂ provided heterogeneous nucleation sites for the deposition of Ca²⁺ and HPO₄²⁻.

In Vitro Corrosion and Cytocompatibility of a Microarc Oxidation Coating and Poly(L-lactic acid) Composite Coating on Mg-1Li-1Ca Alloy for Orthopedic Implants

Manipulating the degradation rate of biomedical magnesium alloys poses a challenge. The characteristics of a microarc oxidation (MAO), prepared in phytic acid, and poly(L-lactic acid) (PLLA) composite coating, fabricated on a novel Mg-1Li-1Ca alloy, were studied through field emission scanning electron microscopy (FE-SEM), electron probe X-ray microanalysis (EPMA), energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD). The corrosion behaviors of the samples were evaluated via hydrogen evolution, potentiodynamic polarization and electrochemical impedance spectroscopy in Hanks' solution. The results indicated that the MAO/PLLA composite coatings significantly enhanced the corrosion resistance of the Mg-1Li-1Ca alloy. MTT and ALP assays using MC3T3 osteoblasts indicated that the MAO/PLLA coatings greatly improved the cytocompatibility, and the morphology of the cells cultured on different samples exhibited good adhesion. Hemolysis tests showed that the composite coatings endowed the Mg-1Li-1Ca alloys with a low hemolysis ratio. The increased solution pH resulting from the corrosion of magnesium could be tailored by the degradation of PLLA. The degradation mechanism of the composite coatings was discussed. The MAO/PLLA composite coating may be appropriate for applications on degradable Mg-based orthopedic implants.

In vitro corrosion of pure magnesium and AZ91 alloy-the influence of thin electrolyte layer thickness

In vivo degradation predication faces a huge challenge via in vitro corrosion test due to the difficulty for mimicking the complicated microenvironment with various influencing factors. A thin electrolyte layer (TEL) cell for in vitro corrosion of pure magnesium and AZ91 alloy was presented to stimulate the in vivo corrosion in the micro-environment built by the interface of the implant and its neighboring tissue. The results demonstrated that the in vivo corrosion of pure Mg and the AZ91 alloy was suppressed under TEL condition. The AZ91 alloy was more sensitive than pure Mg to the inhibition of corrosion under a TEL thickness of less than 200 µm. The TEL thickness limited the distribution of current, and thus localized corrosion was more preferred to occur under TEL condition than in bulk solution. The TEL cell might be an appropriate approach to simulating the in vivo degradation of magnesium and its alloys.

Corrosion resistance of layer-by-layer assembled polyvinylpyrrolidone/polyacrylic acid and amorphous silica films on AZ31 magnesium alloys

A layer-by-layer (LbL)-assembled composite coating containing SiO₂ and a biocompatible polyvinylpyrrolidone (PVP) and polyacrylic acid (PAA) multi-layer, designated as SiO₂/(PVP/PAA)₅, was prepared on AZ31 Mg alloy via dip-coating.

In vitro degradation of pure Mg in response to glucose

Magnesium and its alloys are promising biodegradable biomaterials but are still challenging to be used in person with high levels of blood glucose or diabetes. To date, the influence of glucose on magnesium degradation has not yet been elucidated, this issue requires more attention. Herein, we present pure Mg exhibiting different corrosion responses to saline and Hank’s solutions with different glucose contents, and the degradation mechanism of pure Mg in the saline solution with glucose in comparison with mannitol as a control. On one hand, the corrosion rate of pure Mg increases with the glucose concentration in saline solutions. Glucose rapidly transforms into gluconic acid, which attacks the oxides of the metal and decreases the pH of the solution; it also promotes the absorption of chloride ions on the Mg surface and consequently accelerates corrosion. On the other hand, better corrosion resistance is obtained with increasing glucose content in Hank’s solution due to the fact that glucose coordinates Ca²⁺ ions in Hank’s solution and thus improves the formation of Ca-P compounds on the pure Mg surface. This finding will open up new avenues for research on the biodegradation of bio-Mg materials in general, which could yield many new and interesting results.