Intraoral low-temperature degradation of monolithic zirconia dental prostheses: 5-year results of a prospective clinical study with ex vivo monitoring

OBJECTIVES

To investigate the 5-year intraoral evolution and kinetics of low-temperature degradation (LTD) of second-generation monolithic prostheses made of 3% molar yttrium-doped tetragonal zirconia polycrystal (3Y-TZP) and the influence of masticatory mechanical stresses and glaze layer on this evolution.

METHODS

A total of 101 posterior tooth elements were included in this prospective clinical study, which comprised ex vivo LTD monitoring (at baseline, 6 months, 1 year, 2 years, 3 years, and 5 years) using Raman spectroscopy (n = 2640 monoclinic phase measurement points per evaluation time) and scanning electron microscopy (SEM). Four types of areas (1-2 mm2 surface, six on molars, and four on premolars) were analysed on each element surface: occlusal, axial, glazed, or unglazed. Raman mapping, high-resolution SEM, and focused ion beam-SEM were performed on selected samples.

RESULTS

The dental prostheses developed a tetragonal-to-monoclinic transformation at the extreme surface of the material after six months in a buccal environment, and this process increased significantly over time. Over the five years of monitoring, the transformation developed nonuniformly with the presence of localised clusters of monoclinic grains. Tribological stresses generate grain pull-out from these clusters, which may raise questions regarding the release of 3Y-TZP nanoparticles into the body. The prosthesis fracture rate was 4.5% after 5 years.

SIGNIFICANCE

LTD developed in vivo on the surfaces of 3Y-TZP dental prostheses and progressed slowly but significantly over time, up to 5 years investigation. However, the effects of aging on the failure rate recorded and of zirconia nanoparticles released into the body require further investigation.

Fracture Resistance of Posterior Tooth-Supported Cantilever Fixed Dental Prostheses of Different Zirconia Generations and Framework Thicknesses: An In Vitro Study

The rehabilitation of free-end situations is a frequent indication in prosthetic dentistry. Cantilever fixed dental prostheses (cFDPs) made of 1st and 2nd generation zirconia are one treatment option. Due to a unique gradient technology, combinations of different zirconium dioxide generations are thus feasible in one restoration. However, data about these materials are rare. The purpose of this study was therefore to investigate the fracture resistance and fracture modes of tooth-supported cFDPs fabricated from different zirconia materials (gradient technology) and different framework thicknesses. A total of 40 cFDPs were fabricated using the CAD/CAM approach and belonged to five test groups. The different groups differed in the yttria content, the proportion of the tetragonal/cubic phases, or in wall thickness (0.7 mm or 1 mm). After completion, the cFDPs were subjected to thermal cycling and chewing simulation (1.2 × 106 load cycles, 108 N load). Afterwards, cFDPs were statically loaded until fracture in a universal testing machine. A non-parametric ANOVA was compiled to determine the possible effects of group membership on fracture resistance. In addition, post-hoc Tukey tests were used for bivariate comparisons. The mean fracture loads under axial load application ranged from 288 to 577 N. ANOVA detected a significant impact of the used material on the fracture resistances (p < 0.001). Therefore, the use of cFDPs fabricated by gradient technology zirconia may not be unreservedly recommended for clinical use, whereas cFPDs made from 3Y-TZP exhibit fracture resistance above possible masticatory loads in the posterior region.

Evaluation of Feasibility on Dental Zirconia-Accelerated Aging Test by Chemical Immersion Method

The aim of this study was to investigate the low-temperature degradation (LTD) kinetics of tetragonal zirconia with 3 mol% yttria (3Y-TZP) dental ceramic using two degradation methods: hydrothermal degradation and immersed degradation. To study transformation kinetics, we prepared 3Y-TZP powders. We pressed these powders uniaxially into a stainless mold at 100 MPa. We then sintered the compacted bodies at intervals of 50 °C between 1300 °C and 1550 °C and immersed the specimens at various temperatures from 60 °C to 80 °C in 4% acetic acid or from 110 °C to 140 °C for the hydrothermal method. We used a scanning electron microscope (SEM) to confirm crystalline grain size and used X-ray diffraction to analyze the zirconia phase. As the sintering temperature increased, the calculated crystalline grain size also increased. We confirmed this change with the SEM image. The higher sintering temperatures were associated with more phase transformation. According to the Mehl-Avrami-Johnson equation, the activation energies achieved using the hydrothermal method were 101 kJ/mol, 95 kJ/mol, and 86 kJ/mol at sintering temperatures of 1450 °C, 1500 °C, and 1550 °C, respectively. In addition, the activation energies of the specimens immersed in 4% acetic acid were 60 kJ/mol, 55 kJ/mol, 48 kJ/mol, and 35 kJ/mol, with sintered temperatures of 1400 °C, 1450 °C, 1500 °C, and 1550 °C, respectively. The results showed that a lower sintering temperature would restrain the phase transformation of zirconia because of the smaller crystalline grain size. As a result, the rate of LTD decreased.

In vitro comparison of physical characteristics of milled versus printed zirconia discs

PURPOSE

The purpose of this study was to compare the dimensional accuracy, translucency, and biaxial flexural strength of milled zirconia (MZ) versus 3D-printed zirconia (PZ) discs.

MATERIALS & METHODS

A circular disc measuring 14.0 mm in diameter and 1.20 mm in thickness was designed using computer-aided design (CAD) software. The resulting standard tessellation language (STL) file was used both as a control and to fabricate 36 zirconia (3Y-TZP) disc specimens (n = 36): 18 were milled (group MZ) and 18 were 3D-printed (group PZ). The diameter and thickness of each disc were measured using a digital caliper. Translucency was evaluated using a calibrated dental colorimeter. The flexural strength was determined using the piston-on-three-ball biaxial flexure test. All measurements were done by one blinded examiner. The statistical significance level was set to α = 0.05.

RESULTS

The MZ discs had significantly more accurate dimensions than the PZ discs in both diameter and thickness when compared to the control CAD software-designed disc. The MZ discs exhibited significantly higher translucency (translucency parameter (TP) = 16.95 ±0.36 vs. 9.24 ±1.98) and biaxial flexural strength (996.16 ±137.37 MPa vs. 845.75 ±266.16 MPa) than the PZ discs. Finally, MZ possessed a significantly higher Weibull modulus relative to PZ.

CONCLUSIONS

The results showed that the milled specimens achieved better dimensional accuracy and were more translucent, stronger, and less prone to failure than printed specimens.

The Influence of Alumina Airborne-Particle Abrasion with Various Sizes of Alumina Particles on the Phase Transformation and Fracture Resistance of Zirconia-Based Dental Ceramics

The surface of zirconia-based dental ceramic restorations require preparation prior to adhesive cementation. The purpose of this study was to assess the influence of airborne-particle abrasion with different sizes of alumina particles (50 μm, 110 μm, or 250 μm) on the mechanical strength of zirconia-based ceramics' frameworks and on the extent of phase transformations. A fracture resistance test was performed. The central surface of the frameworks was subjected to a load [N]. The identification and quantitative determination of the crystalline phase present in the zirconia specimens was assessed using X-ray diffraction. The Kruskal-Wallis one-way analysis of variance was used to establish significance (α = 0.05). The fracture resistance of zirconia-based frameworks significantly increases with an increase in the size of alumina particles used for air abrasion: 715.5 N for 250 μm alumina particles, 661.1 N for 110 μm, 608.7 N for 50 μm and the lowest for the untreated specimens (364.2 N). The X-ray diffraction analysis showed an increase in the monoclinic phase content after air abrasion: 50 μm alumina particles-26%, 110 μm-40%, 250 μm-56%, and no treatment-none. Air abrasion of the zirconia-based dental ceramics' surface with alumina particles increases the fracture resistance of zirconia copings and the monoclinic phase volume. This increase is strongly related to the alumina particle size.

Current classification of zirconia in dentistry: an updated review

Zirconia, a crystalline oxide of zirconium, holds good mechanical, optical, and biological properties. The metal-free restorations, mostly consisting of all-ceramic/zirconia restorations, are becoming popular restorative materials in restorative and prosthetic dentistry choices for aesthetic and biological reasons. Dental zirconia has increased over the past years producing wide varieties of zirconia for prosthetic restorations in dentistry. At present, literature is lacking on the recent zirconia biomaterials in dentistry. Currently, no article has the latest information on the various zirconia biomaterials in dentistry. Hence, the aim of this article is to present an overview of recent dental zirconia biomaterials and tends to classify the recent zirconia biomaterials in dentistry. This article is useful for dentists, dental technicians, prosthodontists, academicians, and researchers in the field of dental zirconia.

Transient thermal stresses developed during speed sintering of 3 mol% yttria-stabilized tetragonal zirconia polycrystals

OBJECTIVES

To investigate transient thermal stresses that developed in 3Y-TZP green compacts during speed sintering.

METHODS

A total of 312 disc-shaped green compacts (Ø17.1 ×1, 1.5, 2, 2.5, 3 mm) were cold-isostatically pressed from 3Y-TZP powder (Zpex, Tosoh Corp.) for speed sintering studies as well as compositional analysis and biaxial flexural strength measurements (both at room temperature and following heating at 90 °C/min to 500 °C). Flexural strength was determined using the piston-on-3-ball method. Phase assemblies were analyzed using the X-ray diffraction method. Effects of heating/cooling rates on transient stresses were investigated by conducting definitive sintering studies to determine the threshold for fracture. Finite element analysis (FEA) was used to validate the experimental findings using measured thermomechanical properties.

RESULTS

The bulk and relative density of the green compact were 2.95 ± 0.03 g/cm3 and 48.52% ± 0.45%. The flexural strength was drastically decreased from 10.3 ± 0.4 MPa to 1.09 ± 0.07 MPa following heating at 90 °C/min to 500 °C. The monoclinic and tetragonal contents were 54.9% and 45.1%, respectively. The threshold for fracture was located at 500 °C during the first heating stage with a 90 °C/min heating rate in specimens of 2.5 mm thickness or greater. No fractures occurred in the second heating stage and cooling phase. The FEA estimated that the principal transient tensile stress was ∼1.14 MPa at 500 °C during the heating phase, which exceeded the corresponding flexural strength (1.09 ± 0.07 MPa).

SIGNIFICANCE

Advanced FEA methods are an accurate and efficient tool to analyze the history of transient stresses during sintering of ceramic dental restorations.

Microstructure, composition, and flexural strength of different layers within zirconia materials with strength gradient

OBJECTIVES

The aim of this study was to compare composition, microstructure, and mechanical strength of current multilayer zirconia blanks.

METHODS

Bar shaped specimens were made from several layers of multilayer zirconia blanks (Cercon ht ML, Dentsply Sirona, US; Katana Zirconia YML, Kuraray, J;SHOFU Disk ZR Lucent Supra, Shofu, J; priti multidisc ZrO₂ Multi Translucent, Pritidenta, D; IPS e.max ZirCAD Prime, Ivoclar Vivadent, FL). Flexural strength was determined in a three-point bending test on extra-thin bars. X-ray diffraction (XRD) with Rietveld refinement was used to assess crystal structure and scanning electron microscopy (SEM) imaging to visualize the microstructure of each material and layer.

RESULTS

Mean flexural strength varied between 467.5 ± 97.5 MPa (top layer, IPS e.max ZirCAD Prime) and 898.0 ± 188.5 MPa (bottom layer, Cercon ht ML) with significant (p ≤ 0.055) differences between the individual layers. XRD indicated 5Y-TZP for enamel-layers, 3Y-TZP for dentine-layers, individual mixtures of 3Y-TZP, 4Y-TZP, or 5 Y-TZP for intermediate layers. SEM analysis showed grain sizes between approx. 0.15 and 4 µm. Grain size tended to decrease from top to bottom layers.

SIGNIFICANCE

The investigated blanks differ predominantly in the intermediate layers. In addition to dimensioning of restorations, the milling position in the blanks must also be taken into account when using multilayer zirconia as restorative material.

Comparison of Testing Designs for Flexural Strength of 3Y-TZP and 5Y-PSZ Considering Different Surface Treatment

The aim of this study was to analyze the influence of different surface treatments and the corresponding surface roughness on the ball-on-three-balls test and piston-on-three-balls test for measuring flexural strength 3Y-TZP and 5Y-PSZ. Additionally, the influence of cutting the material into the specimens when pre-sintered or fully sintered was analyzed. A total of 120 specimens for each material group, 3Y-TZP zirconia (Katana HT, Kuraray) and the 4 different layers of multilayered 5Y-PSZ zirconia (Katana UTML, Kuraray), were produced. The used material was cut into half of the specimens in a fully sintered stage, the other half was cut when pre-sintered. Each subgroup was divided into 3 different surface treatment groups being air abraded with 50 µm alumina particles at 1 bar pressure, ground with 600 SiC paper or polished up to 1 µm with a polycristalline diamond suspension. These were then analyzed by X-ray diffraction (XRD) (N = 3) and tested for flexural strength using the ball-on-three-balls test (N = 10) or piston-on-three-balls test (N = 10). For 3Y-TZP groups different surface roughness did not result in statistically significant differences in flexural strength but cutting the specimens in fully sintered state significantly reduced flexural strength of 1133 ± 109 to 741 ± 81 MPa. For 5Y-PSZ groups air abrasion of the specimens with alumina particles significantly reduced the flexural strength of 562 ± 68 MPa to 358 ± 58 MPa. Cutting and surface treatment in pre-sintered or fully sintered state had no significant influence. Flexural strength testing with the ball-on-three-balls test resulted in about 20% higher strengths compared to the piston-on-three-balls test. Results of both tests showed the same tendencies when compared.

Fracture toughness of 3Y-TZP ceramic measured by the Chevron-Notch Beam method: A round-robin study

OBJECTIVE

This interlaboratory round robin test investigated the robustness of the Chevron-Notch Beam (CNB) test method and the effect of the processing and testing variations on the fracture toughness of a dental 3Y-TZP ceramic.

METHODS

The round robin test was performed precisely following the procedures recommended in ISO 24370:2005 and applied on a commercial 3Y-TZP ceramic (product information). A total of 335 test specimens with dimensions 3×4 x 45 mm³ was equally distributed among 10 participating laboratories of varying experience in fracture toughness testing. A standard operating procedure was defined with either narrow processing tolerances or alternative (wider) processing tolerances (as proposed in ISO 24370). Fracture toughness data (series 2) was analyzed using one way ANOVA followed by post hoc Tukey HSD test and 95% Confidence Intervals (CI) were computed (p < 0.05). A further, preceding round-robin (series 1) test was conducted with - more possible variations of test conditions regarding CNB notch processing and storage conditions. Those results are summarized in the supplement and discussed with the actual ISO 24370 test.

RESULTS

Fracture toughness of the 3Y-TZP ceramic material, summarized over all laboratories was measured to K_Ic = 4.48 ± 0.11 MPam^0.5 for the standard processing tolerance and K_Ic = 4.55 ± 0.31 MPam^0.5 for the alternative tolerance. The results revealed a significant influence of cutting offset and notch geometry on K_Ic when using CNB method. The test medium also has a significant influence on K_Ic in terms of reduced fracture toughness under the influence of water. With defined testing conditions the number of valid tests and reduced standard deviation increased. In case of strictly following such standard operation procedures, K_Ic can be determined with high reliability. There is no difference between the involved laboratories, but significant influence of cutting offset on K_IC was observed.

SIGNIFICANCE

The CNB method is suitable method for determination of K_Ic on fine-grained ceramics such as 3Y-TZP ceramic. By using tighter tolerances for processing and testing, i.e. closely following the ISO 24370 procedure, a highly-precise evaluation of fracture toughness with low data variation is achievable. The information of the storage medium should always be reported along with the data. CNB fracture toughness testing is an alternative method compared to Single-edge V-notch beam (SEVNB), especially for fine-grained ceramics.

Fracture behavior of cantilever fixed dental prostheses fabricated from different zirconia generations

OBJECTIVE

The aim of this study was to compare the fracture behavior of cantilever fixed dental prostheses (FDPs) fabricated from 3Y-TZP, 4Y-TZP, or 5Y-TZP zirconia.

METHOD AND MATERIALS

Posterior cantilever FDPs (three groups, each n = 16) were digitally designed and milled. After sintering, eight specimens/group were stored in demineralized water for 72 hours; eight specimens/group were subjected to accelerated aging using chewing simulation with thermal cycling (1,200,000 × 50 N; 2 × 3,000 × 5°C/55°C; H2O, 2 minutes/cycle) and finally stored in demineralized water for 24 hours. The cantilever FDPs were then statically loaded to failure to determine fracture load. Phase transformation towards the monoclinic phase was controlled with x-ray diffractometry.

RESULTS

One failure was identified after accelerated aging in the 5Y-TZP group. Fracture load decreased with increasing yttria content and decreasing bending strength. Accelerated aging using chewing simulation with thermal cycling caused a significant decline in fracture load. All FDPs failed in the area of the prepared tooth and in proximity to the cantilever, where the largest bending moment occurred. The yttria content had no influence on the type of fracture. With increasing yttria content, the relation between deformation and fracture load decreased only slightly. On the surface of FDPs that had been subjected to chewing simulation, no phase transformation towards the monoclinic phase (eg, low temperature degradation) was detected.

CONCLUSION

Within the limitations of a laboratory study, the data indicate that 3Y-, 4Y-, and 5Y-TZP may be employed as material for the fabrication of permanent posterior cantilever FDPs. However, more data are necessary to finally advocate the application of 5-Y-TZP. (Quintessence Int 2022;53:414-422; doi: 10.3290/j.qi.b2793243).

The effect of endodontic access preparation on the failure load resistance of a 3Y-TZP monolithic zirconia crown

The effect of endodontic access preparation on the failure load resistance of 3Y-TZP zirconia crowns was accomplished by preparing human molars and luting monolithic zirconia crowns with a self-adhesive resin cement. Besides the intact control, teeth received endodontic access preparations and then grouped (n = 12) into a positive control (no access repair), dentin core replacement only and complete access repair groups. Specimens were axially tested until failure with results of no significant difference between the failure load of intact controls and the complete access repair group. However, the positive control and dentin replacement only groups failed at significantly lower loads. Under the conditions of this study, there was no significant failure load difference between 3Y-TZP monolithic zirconia crowns with repaired endodontic access preparations to that evidenced by an unprepared control. Although this evidence is encouraging, caution is advised and definitive recommendations cannot be made until verified by clinical studies.

Effect of Acid Mixtures on Surface Properties and Biaxial Flexural Strength of As-Sintered and Air-Abraded Zirconia

The aim of this work was to evaluate the effects of application time of an acid mixture solution on the surface roughness, phase transformation, and biaxial flexural strength of 3Y-TZP after sintering or air abrasion. For the biaxial flexural strength measurement, 220 3Y-TZP disk-shaped specimens were prepared after as-sintering or air abrasion. The etching solution comprised a mixture of hydrofluoric acid, sulfuric acid, hydrogen peroxide, methyl alcohol, and purified water. The samples were divided into 11 subgroups according to the etching times (Control, 1, 2, 3, 5, 8, 10, 12, 15, 20, and 30 min). The results showed that acid treatment on both as-sintered and air-abraded 3Y-TZP surfaces increased the surface roughness. However, it had no significant effects on the monoclinic phase or flexural strength of as-sintered zirconia. The monoclinic phase and flexural strength of air-abraded zirconia increased sharply after air abrasion; however, they gradually decreased after acid treatment, to a similar level to the case of the untreated surface. Surface treatment with acid mixture increased the roughness, but the lack of increase of monoclinic phase is thought to be because the loose monoclinic particles remaining on the surface were removed through the etching process.

Impact of varying step-stress protocols on the fatigue behavior of 3Y-TZP, 4Y-TZP and 5Y-TZP ceramic

OBJECTIVE

To test the impact of three varying step-stress protocols on the fatigue behavior of two 3Y-TZP, one 4Y-TZP and one 5Y-TZP zirconia materials.

METHODS

Eight specimens per zirconia material (N = 32) were selected for static testing to determine the start load for dynamic tests (30% of the mean value of static fracture load). 45 specimens per material (N = 180) were used for dynamic load tests using three step-stress protocols: 1. 50 N/5000 cycles; 2. 5% of static load/5000 cycles, and 3. 10 N/1000 cycles. Following materials were tested: 3Y-TZP_{(<0.25 Al2O3)} (O: opaque) 3Y-TZP_{(<0.05 Al2O3)} (T: translucent), 4Y-TZP_{(<0.01 Al2O3)} (ET: extra translucent) and 5Y-TZP_{(<0.01 Al2O3)} (HT: high translucent). The specimens (4 ± 0.02 × 3 ± 0.02 × 45 mm) were placed centrally on the support rolls and the load was applied perpendicularly over the 4 mm specimen side (∼4-point flexural strength according to the DIN 6872:2019). Data was analyzed with Kolmogorov-Smirnov-test, t-test, one-way ANOVA with post-hoc Scheffé-test, Chi-square-test, Kaplan-Meier with Log-Rank-test and two-parametric Weibull analysis (p < 0.05).

RESULTS

The step-stress protocols showed no impact on the fracture load or Weibull modulus within one zirconia material. However, the zirconia materials T, ET and HT showed differences in cycle number to fracture between the step-stress protocols (T: 3 > 2 > 1; ET: 2 > 3 > 1; HT: 2, 3 > 1) with lowest cycle number to fracture for protocol 1. Within one step-stress protocol, the cycle number to fracture varied according to the zirconia material as follows: 1: T, O ≥ O, ET > HT; 2: ET > O, T, HT; 3: O, T, ET > HT. Cracking started at the tensile side of the specimens at all times. All specimens showed typical compression curls (single or double). Fragmentation patterns were similar for all materials with a lot of crack branching and fragmentation due to secondary cracks indicating high energy fractures.

SIGNIFICANCE

Dynamic fatigue tests seem to provide important information on the long-term stability of zirconia materials. Zirconia materials with higher opacity seem to be more robust towards varying step-stress protocols than translucent zirconia materials. Regarding expenditure of time, a step-stress protocol with a load increase of 50 N every 5000 cycles seems favorable to gain information on the long-term stability of zirconia materials.

Intraoral low-temperature degradation of monolithic zirconia dental prostheses: Results of a prospective clinical study with ex vivo monitoring

OBJECTIVE

To investigate the intraoral development and kinetics of low-temperature degradation (LTD) in second-generation 3 mol.% yttria-doped tetragonal zirconia polycrystal (3Y-TZP) monolithic prostheses, as well as the influence of masticatory mechanical stress and glaze layer on it.

METHODS

A total of 101 posterior tooth elements were included in a prospective clinical study, which included ex vivo LTD monitoring (at baseline, 6 months, 1 year, and 2 years) using Raman spectroscopy (n = 2640 monoclinic phase measurement points per evaluation time) and SEM. Four types of areas (1-2 mm² surface, 6 on molars, and 4 on premolars) were analyzed on each element surface: occlusal, axial, glazed, or unglazed. Raman depth mapping and high-resolution SEM were performed on the selected samples.

RESULTS

LTD developed in 3Y-TZP monolithic restorations 6 months after intraoral placement and progressed with time. After two years, the tetragonal-to-monoclinic transformation was non-uniform, with the presence of localized clusters of transformed grains. In axial areas, the grain aspect was typical of the classical nucleation-growth process reported for LTD, which progresses from the surface to a depth of several tens of microns. However, in occlusal areas, tribological stress generated surface crushing and grain pull-out from the clusters, which induced an underestimation of the aging process when the evaluation was limited to monoclinic phase quantification. Glazing cannot be considered a protection against LTD.

SIGNIFICANCE

If LTD occurs in dental prostheses in the same way as in orthopedic prostheses, its clinical impact is unknown and needs to be further studied.

In vivo aging of zirconia dental ceramics - Part I: Biomedical grade 3Y-TZP

OBJECTIVE

In vivo aging of biomedical grade 3Y-TZP ceramics in the oral environment was assessed and compared to artificially accelerated in vitro hydrothermal aging extrapolations at 37°C.

METHODS

88 discs were pressed and sintered (1450-1500°C) from two commercial 3Y-TZP compositions containing 0.25% Al₂O₃ to generate finer- and coarser-grained specimens. As-sintered (AS) and airborne-particle abraded (APA; 50μm Al₂O₃) surfaces were investigated. In vivo aging was performed by incorporating specimens in lingual flanges of complete dentures of 12 edentulous volunteers who wore them continuously for up to 24 months. For comparison, in vitro hydrothermal aging at 134°C was also performed and analysed by XRD and (FIB)-SEM. Data was statistically analysed with linear regression models.

RESULTS

Finer and coarser-grained specimens exhibited statistically insignificant differences in aging in vivo. The monoclinic fraction (X_m) on AS surfaces abruptly increased to ∼8% after 6 months. The aging process then proceeded with slower linear kinetics (∼0.24%/month). After 24 months, X_m reached ∼12%. The calculated maximum transformed layer was 0.385μm representing one layer of transformed grains. APA surfaces were highly aging resistant. The initial X_m of ∼4.0% linearly increased by 0.03%/month in vivo. In vitro aging exhibited an initial induction period, followed by linear aging kinetics. Coarser-grained AS surfaces aged significantly faster than fine-grained (2.41%/h compared to 2.16%/h). APA discs aged at a rate of 0.3%/h in vitro. Microcracking within a single grain and pull-out of grain clusters were observed on aged AS surfaces.

SIGNIFICANCE

Biomedical grade 3Y-TZP was susceptible to in vivo aging. After 2 years in vivo, the aging kinetics were almost 3-times faster than the generally accepted in vitro-in vivo extrapolation.

Effect of high-speed sintering on the flexural strength of hydrothermal and thermo-mechanically aged zirconia materials

OBJECTIVE

To investigate the influence of high-speed and conventional sintering on the flexural strength (FS) of three zirconia materials initial and after artificial aging.

METHODS

Milled zirconia specimens (3Y-TZP: ZI and Zolid; 4Y-TZP: Zolid HT+; Amann Girrbach AG; N = 288, n = 96/group) were sintered in a high-speed sintering protocol (final temperature 1580 °C, n = 48/subgroup) or a conventional sintering protocol (control group, final temperature 1450 °C, n = 48/subgroup). FS was tested initially and after artificial aging (10 h in an autoclave or 1,200,000 chewing cycles; n = 16/subgroup). Univariate ANOVAs, post-hoc Scheffé, partial eta-squared, Kolmogorov-Smirnov-, Kruskal-Wallis- and Mann-Whitney-U-test were performed (p < 0.05).

RESULTS

ZI showed the highest and HT+ the lowest FS, regardless of the sintering protocols and aging regimens (p < 0.001). High-speed sintered HT+ showed higher initial FS than the control group (p < 0.001). ZI (p < 0.001-0.004) and Zolid (p < 0.001-0.007) showed higher FS after thermo-mechanical aging. High-speed sintered HT+ showed higher FS in the initial stage (p < 0.001). The Weibull modulus of the three thermo-mechanically aged materials was negatively influenced by high-speed sintering.

SIGNIFICANCE

As shorter sintering times represent a cost and time efficient alternative, high-speed sintering is a valid alternative to conventional sintering protocols.

Preparation, Microstructure, Mechanical Properties and Biocompatibility of Ta-Coated 3Y-TZP Ceramic Deposited by a Plasma Surface Alloying Technique

A Ta coating has been successfully fabricated on the surface of zirconia polycrystals ceramic (3 mol% yttria, 3Y-TZP) by a plasma surface alloying technique. The X-ray diffraction (XRD) and scanning electron microscopy (SEM) results showed that a α-Ta coating with a continuous and compact surface morphology which consisted of a deposited layer with a thickness of 390 nm and a diffusion layer with a thickness of 200 nm covered the 3Y-TZP. Due to the effect of inhabitation the t→m transformation by the deposited Ta coating, the biaxial flexural strength caused by the phase transformation during hydrothermal aging is reduced e.g. p < 0.05 after 20 h and/or 100 h. In addition, the Ta coating shows non-cytotoxicity and improved proliferation ability of osteoblasts.

The effects of surface grinding and polishing on the phase transformation and flexural strength of zirconia

PURPOSE

The purpose of this in vitro study was to evaluate the effect of surface grinding and polishing procedures using high speed zirconia diamond burs with different grit sizes on the phase transformation and flexural strength of zirconia.

MATERIALS AND METHODS

Forty disc shape specimens (15 × 1.25 mm) with a cylindrical projection in the center of each disc (1 × 3 mm) were fabricated with 3Y-TZP (Prettau, Zirkonzahn, Italy). The specimens were divided into 4 groups (n=10) according to the grinding and polishing procedures: Control group - grinding (coarse-grit diamond bur), Group 1 - grinding (coarse-grit diamond bur) + polishing, Group 2 - grinding (fine-grit diamond bur) + polishing, and Group 3 - grinding (fine grit diamond bur). Each specimen was analyzed by 3D-OM, XRD analysis, and biaxial flexural strength test.

RESULTS

Based on the surface morphology by 3D-OM images, polished specimens showed smoother surface and lower roughness value (Ra). In the result of XRD analysis, partial phase transformation from tetragonal to monoclinic zirconia occurred in all groups. Control group, ground with a coarse grit diamond bur, showed more t→m phase transformation and lower flexural strength than Groups 1 and 2 significantly.

CONCLUSION

The flexural strength in all specimens after grinding and polishing showed over 500 MPa, and those were clinically acceptable. However, grinding with a coarse grit diamond bur without polishing induced the phase transformation and low strength. Therefore, surface polishing is required for the occlusal adjustment using a high speed zirconia diamond bur to reduce the phase transformation and to prevent the decrease of flexural strength of zirconia.

Strength limits in mesoscaled 3Y-TZP ceramics for micro-surgical instruments

Micro-surgical instruments are a new application for mesoscale ceramics formed using the lost mold-rapid infiltration forming (LM-RIF) process. Instrument strength and reliability are the foremost concerns for this sensitive application. It is hypothesized that increasing grain size can improve the damage tolerance of the parts associated with the transformation toughening in the 3Y-TZP material, while retaining high strength. In this work, mesoscale bend bars (314 × 22 × 18 µm) of 3Y-TZP fabricated using the LM-RIF process were heat treated at 1400 °C for 1 h, 8 h, or 16 h, respectively, to obtain samples with different grain sizes. Strength tests were performed under three-point bending and results were evaluated using Weibull statistics. Fractographic and confocal Raman spectroscopic analyses were carried out to interpret the data. Experimental findings showed that the characteristic strength decreased with increasing grain size contrary to the damage tolerance hypothesis. An Orowan-Petch model was recalled to correlate the strength with the flaw size to grain size ratio. At fine grain sizes the strength was controlled by the flaws introduced by the LM-RIF process, whereas at large grain sizes the strength become more grain size controlled. Although larger-grained samples did have a higher propensity to transform, and thus increase toughening, exaggerated grain growth in some of the specimens tested caused an additional flaw population which led to an overall lower strength. Finally, based on the experimental observations and fracture mechanics considerations, we believe that an upper bound of ∼2.5 GPa exists for the strength of mesoscale as-fabricated 3Y-TZP ceramic parts.

Effect of Surface Modification on In-Depth Transformations and Flexural Strength of Zirconia Ceramics

PURPOSE

Chairside surface adjustments of zirconia dental restorations enhance the toughening stress-induced tetragonal-to-monoclinic phase transformation and domain reorientation by ferro-elastic domain switching (FDS), but also trigger subsurface damage, which could compromise long-term clinical performance. The purpose of this study was to assess the depth of phase transformation, associated FDS, and flexural strength of dental zirconia (BruxZir HT 2.0), after chairside surface treatments.

MATERIALS AND METHODS

Square specimens were sectioned from CAD/CAM blocks and sintered according to manufacturer's recommendations (n = 30). They were left as-sintered (AS; control), air abraded with fine (AAF) or coarse (AAC) alumina particles, ground (G) or ground and polished (GP). Roughness was measured by profilometry. Crystalline phases were investigated by grazing incidence X-ray diffraction (GIXRD) (n = 3). GIXRD data were fit using semi-log regression protocols to assess transformation depth and extent of FDS. The mean biaxial flexural strength was measured according to ISO 6872. Subsurface damage was assessed from SEM images using a bonded polished interface configuration. Flaw distribution was assessed by Weibull analysis. Results were analyzed by Kruskal-Wallis with Tukey's adjustment for multiple comparisons (p < 0.05).

RESULTS

Air-abraded and ground groups exhibited higher mean surface roughness than control. AAF group exhibited the highest flexural strength (1662.6 ± 202.6 MPa) with flaw size (5.9 ± 1.8 μm) smaller than transformation (14.5 ± 1.2 μm) or FDS depth (19.3 ± 1.1 μm), followed by GP group (1567.2 ± 209.7 MPa) with smallest FDS depth (9.3 ± 2.0 μm) and flaw size (2.6 ± 1.8 μm), but without m-phase. AAC group (1371.4 ± 147.6 MPa) had the largest flaw size (40.3 ± 20.3 μm), transformation depth (47.2 ± 3.0 μm) and FDS depth (41.2 ± 2.2 μm). G group (1357.0 ± 196.7 MPa) had the smallest transformation depth (8.6 ± 1.5 μm), and mean FDS depth (19.8 ± 3.7 μm) and flaw size (18.6 ± 3.1 μm). AAC and AAF exhibited the highest Weibull modulus (11.2 ± 0.4 and 9.8 ± 0.3 μm, respectively).

CONCLUSIONS

Variations in mean biaxial flexural strength were explained by the balance between the depth of toughening mechanisms (phase transformation and FDS) and subsurface damage. AAF and GP groups were the most efficient surface adjustments in promoting the highest mean biaxial flexural strength.

Mechanical performance of polymer-infiltrated zirconia ceramics

OBJECTIVE

The aim of this study was to evaluate the microstructure and mechanical behavior of polymer-infiltrated zirconia ceramics as a function of pre-sintering temperature (1000-1150°C).

METHODS

Polymer-infiltrated zirconia ceramics were prepared by combining the porous zirconia networks and polymer through infiltration and polymerization. XRD was employed to determine phase structure. The microstructure and fracture mechanism were observed by SEM. Flexural strength and fracture toughness were measured by three-point bending method and single-edge-notched beam method, respectively. A nanoindentation system was employed to determine elastic modulus and hardness.

RESULTS

Different porosities and polymer contents can be obtained by tuning the pre-sintered temperature of zirconia ceramic precursors. Zirconia network porosity varies from 46.3% to 34.7% and the relevant polymer content ranges from 18.4wt.% to 12.3wt.% when the pre-sintered temperature is set from 1000°C to 1150°C. The flexural strength, fracture toughness, hardness, and elastic modulus values of the specimen pre-sintered at 1150°C are 240.9MPa, 3.69MPam^1/2, 3.1GPa, and 58.8GPa, respectively.

CONCLUSION

The pre-sintering temperature has a significant effect on the microstructure and mechanical properties of polymer-infiltrated zirconia ceramics and the optimal pre-sintering temperature is 1150°C.

CLINICAL SIGNIFICANCE

Specimen pre-sintered at 1150°C shows tooth-like mechanical properties, suggesting a promising restorative material in dental clinic. Moreover, the synthesis process is simple and can be easily performed in a prosthesis laboratory.

High strength and toughness in chromatic polymer-infiltrated zirconia ceramics

OBJECTIVE

To evaluate the microstructure and mechanical behavior of polymer-infiltrated zirconia ceramics as a function of Fe₂O₃ concentration (0-0.3mol%).

METHODS

Polymer-infiltrated zirconia ceramics with different concentrations of Fe₂O₃ were prepared by infiltration and polymerization. XRD was employed to determine phase structure. The microstructure and fracture mechanism was observed by SEM. Flexural strength and fracture toughness were measured by three-point bending method and single-edge-notched beam method, respectively. Data were analyzed by Weibull distribution. A nanoindentation system was employed to determine elastic modulus and hardness.

RESULTS

With increasing content of Fe₂O₃, the flexural strength, fracture toughness, elastic modulus and hardness are all greatly enhanced and the chromatic behavior also improves significantly. As a tradeoff made between strength and elastic modulus, specimen containing 0.2mol% Fe₂O₃ is found to be the better one, with flexural strength and fracture toughness values being 336.8MPa and 3.91MPam^1/2, respectively. Moreover, it maintains a relatively low elastic modulus of 88.2GPa and a moderate hardness of 4.8GPa, close to those of natural enamel.

SIGNIFICANCE

This polymer-infiltrated zirconia ceramic material is a dental material of biomimetic chromatic and mechanical properties.

Effect of different grinding burs on the physical properties of zirconia

PURPOSE

Grinding with less stress on 3Y-TZP through proper selection of methods and instruments can lead to a long-term success of prosthesis. The purpose of this study was to compare the phase transformation and physical properties after zirconia surface grinding with 3 different grinding burs.

MATERIALS AND METHODS

Forty disc-shaped zirconia specimens were fabricated. Each Ten specimens were ground with AllCeramic SuperMax (NTI, Kahla, Germany), Dura-Green DIA (Shofu Inc., Kyoto, Japan), and Dura-Green (Shofu Inc., Kyoto, Japan). Ten specimens were not ground and used as a control group. After the specimen grinding, XRD analysis, surface roughness test, FE-SEM imaging, and biaxial flexural strength test were performed.

RESULTS

After surface grinding, small amount of monoclinic phase in all experimental groups was observed. The phase change was higher in specimens, which were ground with Dura-Green DIA and AllCeramic SuperMax burs. The roughness of surfaces increased in specimens, which were ground with Dura-Green DIA and AllCeramic SuperMax burs than control groups and ground with Dura-Green. All experimental groups showed lower flexural strength than control group, but there was no statistically significant difference between control group and ground with Dura-Green DIA and AllCeramic SuperMax burs. The specimens, which were ground with Dura- Green showed the lowest strength.

CONCLUSION

The use of dedicated zirconia-specific grinding burs such as Dura-Green DIA and AllCeramic SuperMax burs decreases the grinding time and did not significantly affect the flexural strength of zirconia, and therefore, they may be recommended. However, a fine polishing process should be accompanied to reduce the surface roughness after grinding.