Ultrasound stimulated piezoelectric barium titanate and boron nitride nanotubes in nonconductive poly-ε-caprolactone nanofibrous scaffold for bone tissue engineering

Nanomaterials can provide unique solutions for the problems experienced in tissue engineering by improving a scaffold's physico-bio-chemical properties. With its piezoelectric property, bone is an active tissue with easy adaptation and remodeling through complicated mechanisms of electromechanical operations. Although poly(ε-caprolactone) (PCL) is an excellent polymer for bone tissue engineering, it is lack of conductivity. In this study, piezoelectric barium titanates (BaTiO3) and boron nitride nanotubes (BNNTs) are used as ultrasound (US) stimulated piezoelectric components in PCL to mimic piezoelectric nature of bone tissue. Electric-responsive Human Osteoblast cells on the scaffolds were stimulated by applying low-frequency US during cell growth. Biocompatibility, cell adhesion, alkaline phosphatase activities and mineralization of osteoblast cells on piezo-composite scaffolds were investigated. BaTiO3or BNNTs as reinforcement agents improved physical and mechanical properties of PCL scaffolds.In vitrostudies show that the use of BaTiO3or BNNTs as additives in non-conductive scaffolds significantly induces and increases the osteogenic activities even without US stimulation. Although BaTiO3is one of the best piezoelectric materials, the improvement is more dramatic in the case of BNNTs with the increased mineralization, and excellent chemical and mechanical properties.

Electroconductive Nanofibrous Scaffolds Enable Neuronal Differentiation in Response to Electrical Stimulation without Exogenous Inducing Factors

Among the various biochemical and biophysical inducers for neural regeneration, electrical stimulation (ES) has recently attracted considerable attention as an efficient means to induce neuronal differentiation in tissue engineering approaches. The aim of this in vitro study was to develop a nanofibrous scaffold that enables ES-mediated neuronal differentiation in the absence of exogenous soluble inducers. A nanofibrous scaffold composed of polycaprolactone (PCL), poly-L-lactic acid (PLLA), and single-walled nanotubes (SWNTs) was fabricated via electrospinning and its physicochemical properties were investigated. The cytocompatibility of the electrospun composite with the PC12 cell line and bone marrow-derived mesenchymal stem cells (BMSCs) was investigated. The results showed that the PCL/PLLA/SWNT nanofibrous scaffold did not exhibit cytotoxicity and supported cell attachment, spreading, and proliferation. ES was applied to cells cultured on the nanofibrous scaffolds at different intensities and the expression of the three neural markers (Nestin, Microtubule-associated protein 2, and β tubulin-3) was evaluated using RT-qPCR analysis. The results showed that the highest expression of neural markers could be achieved at an electric field intensity of 200 mV/cm, suggesting that the scaffold in combination with ES can be an efficient tool to accelerate neural differentiation in the absence of exogenous soluble inducers. This has important implications for the regeneration of nerve injuries and may provide insights for further investigations of the mechanisms underlying ES-mediated neuronal commitment.

Multifunctional electrospun nanofibrous scaffold enriched with alendronate and hydroxyapatite for balancing osteogenic and osteoclast activity to promote bone regeneration

Electrospun composite nanofiber scaffolds are well known for their bone and tissue regeneration applications. This research is focused on the development of PVP and PVA nanofiber composite scaffolds enriched with hydroxyapatite (HA) nanoparticles and alendronate (ALN) using the electrospinning technique. The developed nanofiber scaffolds were investigated for their physicochemical as well as bone regeneration potential. The results obtained from particle size, zeta potential, SEM and EDX analysis of HA nanoparticles confirmed their successful fabrication. Further, SEM analysis verified nanofiber's diameters within 200-250 nm, while EDX analysis confirmed the successful incorporation of HA and ALN into the scaffolds. XRD and TGA analysis revealed the amorphous and thermally stable nature of the nanofiber composite scaffolds. Contact angle, FTIR analysis, Swelling and biodegradability studies revealed the hydrophilicity, chemical compatibility, suitable water uptake capacity and increased in-vitro degradation making it appropriate for tissue regeneration. The addition of HA into nanofiber scaffolds enhanced the physiochemical properties. Additionally, hemolysis cell viability, cell adhesion and proliferation by SEM as well as confocal microscopy and live/dead assay results demonstrated the non-toxic and biocompatibility behavior of nanofiber scaffolds. Alkaline phosphatase (ALP) and tartrate-resistant acid phosphatase (TRAP) assays demonstrated osteoblast promotion and osteoclast inhibition, respectively. These findings suggest that developed HA and ALN-loaded PVP/PVA-ALN-HA nanofiber composite scaffolds hold significant promise for bone regeneration applications.

Fabrication and Characterization of Zn Particle Incorporated Fibrous Scaffolds for Potential Application in Tissue Healing and Regeneration

Zinc (Zn) metal and its alloys have received a lot of interest in biomedical applications due to their biodegradability, biocompatibility, antimicrobial activity, and ability to stimulate tissue regeneration. Bulk Zn has been successfully utilized in a variety of implant applications, most notably as bioabsorbable cardiac stents and orthopedic fixation devices, where it provides adequate mechanical properties while also releasing helpful Zn ions (Zn2+) during degradation. Such beneficial ions are dose-dependent and, when released in excess, can induce cellular toxicity. In this study, we hypothesize that embedding Zn metal particles into a polymer nanofibrous scaffold will enable control of the degradation and time release of the Zn2+. We designed and fabricated two polymer scaffolds, polycaprolactone (PCL) and polycaprolactone-chitosan (PCL-CH). Each scaffold had an increasing amount of Zn. Several physicochemical properties such as fiber morphology, crystallinity, mechanical strength, hydrophilicity, degradation and release of Zn2+, thermal properties, chemical compositions, and so forth were characterized and compared with the PCL fibrous scaffold. The biological properties of the scaffolds were evaluated in vitro utilizing direct and indirect cytotoxicity assays and cell viability. All the data show that the addition of Zn changed various physical properties of the PCL and PCL-CH scaffolds except their chemical structure. Further investigation reveals that the PCL-CH scaffolds degrade the Zn particles relatively faster than the PCL because the presence of the hydrophilic CH influences the faster release of Zn2+ in cell culture conditions as compared to the PCL fibrous scaffold. The combined advantages of CH and Zn in the PCL scaffold enriched 3T3 fibroblast cells' survival and proliferation except the ones with the higher concentration of Zn particles. These new composite scaffolds are promising and can be further considered for tissue healing and regeneration applications.

Electrospun Scaffolds as Antimicrobial Herbal Extract Delivery Vehicles for Wound Healing

Herbal extracts have been used in traditional remedies since the earliest myths. They have excellent antimicrobial, anti-inflammatory, and antioxidant activities owing to various bioactive components in their structure. However, due to their inability to reach a target and low biostability, their use with a delivery vehicle has come into prominence. For this purpose, electrospun nanofibrous scaffolds have been widely preferred for the delivery and release of antimicrobial herbal extracts due to the flexibility and operational versatility of the electrospinning technique. Herein, we briefly reviewed the electrospun nanofibrous scaffolds as delivery systems for herbal extracts with a particular focus on the preclinical studies for wound-healing applications that have been published in the last five years. We also discussed the indirect effects of herbal extracts on wound healing by altering the characteristics of electrospun mats.

Preparation, characterization, and bioactivity of reinforced monetite with chitosan-gelatin electrospun composite scaffold for bone tissue engineering

In this study, chitosan-gelatin-monetite (CGM)-based electrospun scaffolds have been developed that closely mimicked the microstructure and chemical composition of the extracellular matrix of natural bone. CGM-based nanofibrous composite scaffolds were prepared with the help of the electrospinning technique, post-cross-linked using EDC and NHS solution to improve their stability in an aqueous environment. The prepared CG scaffold showed an average fiber diameter of 284 ± 17 nm, whereas 5 and 7 wt% monetite containing CGM5 and CGM7 scaffolds, exhibited an average fiber diameter of 390 ± 11 and 435 ± 15 nm, respectively, revealing the fine distribution of monetite particles on the fibrous surface. The distribution of monetite nanoparticles onto the CG nanofibrous surface was confirmed using XRD, FTIR, and EDAX. Moreover, the addition of 7 wt% monetite into the CG electrospun matrix increased their ultimate tensile strength from 2.01 ± 0.05 MPa in the CG scaffold to 11.68 ± 0.09 MPa in the CGM7 scaffold. SBF study and staining with ARS confirmed the higher mineralization ability of monetite-containing scaffolds compared to that revealed by the CG scaffold. The monetite incorporation into the CG matrix improved its osteogenic properties, including pre-osteoblast MG-63 cell adhesion, proliferation, and differentiation, when seeded with the cells. A higher degree of cellular adhesion, spreading, and migration was observed on the monetite-incorporated CG scaffold than that on the CG scaffold. From MTT assay, ALP activity, ARS staining, and immunocytochemistry study, the cultured cells discovered a more conducive microenvironment to proliferate and subsequently differentiate into osteoblast lineage in contact with CGM7 nanofibers rather than that in CGM0 and CGM5. In-vitro results indicated that electrospun CGM-based composite scaffolds could be used as a potential candidate to repair and regenerate new bone tissues.&#xD.

Overview of Electrospinning for Tissue Engineering Applications

Tissue engineering (TE) is an emerging field of study that incorporates the principles of biology, medicine, and engineering for designing biological substitutes to maintain, restore, or improve tissue functions with the goal of avoiding organ transplantation. Amongst the various scaffolding techniques, electrospinning is one of the most widely used techniques to synthesise a nanofibrous scaffold. Electrospinning as a potential tissue engineering scaffolding technique has attracted a great deal of interest and has been widely discussed in many studies. The high surface-to-volume ratio of nanofibres, coupled with their ability to fabricate scaffolds that may mimic extracellular matrices, facilitates cell migration, proliferation, adhesion, and differentiation. These are all very desirable properties for TE applications. However, despite its widespread use and distinct advantages, electrospun scaffolds suffer from two major practical limitations: poor cell penetration and poor load-bearing applications. Furthermore, electrospun scaffolds have low mechanical strength. Several solutions have been offered by various research groups to overcome these limitations. This review provides an overview of the electrospinning techniques used to synthesise nanofibres for TE applications. In addition, we describe current research on nanofibre fabrication and characterisation, including the main limitations of electrospinning and some possible solutions to overcome these limitations.

Topically Applied Biopolymer-Based Tri-Layered Hierarchically Structured Nanofibrous Scaffold with a Self-Pumping Effect for Accelerated Full-Thickness Wound Healing in a Rat Model

Wound healing has grown to be a significant problem at a global scale. The lack of multifunctionality in most wound dressing-based biopolymers prevents them from meeting all clinical requirements. Therefore, a multifunctional biopolymer-based tri-layered hierarchically nanofibrous scaffold in wound dressing can contribute to skin regeneration. In this study, a multifunctional antibacterial biopolymer-based tri-layered hierarchically nanofibrous scaffold comprising three layers was constructed. The bottom and the top layers contain hydrophilic silk fibroin (SF) and fish skin collagen (COL), respectively, for accelerated healing, interspersed with a middle layer of hydrophobic poly-3-hydroxybutyrate (PHB) containing amoxicillin (AMX) as an antibacterial drug. The advantageous physicochemical properties of the nanofibrous scaffold were estimated by SEM, FTIR, fluid uptake, contact angle, porosity, and mechanical properties. Moreover, the in vitro cytotoxicity and cell healing were assessed by MTT assay and the cell scratching method, respectively, and revealed excellent biocompatibility. The nanofibrous scaffold exhibited significant antimicrobial activity against multiple pathogenic bacteria. Furthermore, the in vivo wound healing and histological studies demonstrated complete wound healing in wounded rats on day 14, along with an increase in the expression level of the transforming growth factor-β1 (TGF-β1) and a decrease in the expression level of interleukin-6 (IL-6). The results revealed that the fabricated nanofibrous scaffold is a potent wound dressing scaffold, and significantly accelerates full-thickness wound healing in a rat model.

Recent Advances in Tissue-Engineered Cardiac Scaffolds-The Progress and Gap in Mimicking Native Myocardium Mechanical Behaviors

Heart failure is the leading cause of death in the US and worldwide. Despite modern therapy, challenges remain to rescue the damaged organ that contains cells with a very low proliferation rate after birth. Developments in tissue engineering and regeneration offer new tools to investigate the pathology of cardiac diseases and develop therapeutic strategies for heart failure patients. Tissue -engineered cardiac scaffolds should be designed to provide structural, biochemical, mechanical, and/or electrical properties similar to native myocardium tissues. This review primarily focuses on the mechanical behaviors of cardiac scaffolds and their significance in cardiac research. Specifically, we summarize the recent development of synthetic (including hydrogel) scaffolds that have achieved various types of mechanical behavior-nonlinear elasticity, anisotropy, and viscoelasticity-all of which are characteristic of the myocardium and heart valves. For each type of mechanical behavior, we review the current fabrication methods to enable the biomimetic mechanical behavior, the advantages and limitations of the existing scaffolds, and how the mechanical environment affects biological responses and/or treatment outcomes for cardiac diseases. Lastly, we discuss the remaining challenges in this field and suggestions for future directions to improve our understanding of mechanical control over cardiac function and inspire better regenerative therapies for myocardial restoration.

Mir-122 upregulation and let-7f downregulation combination: The effects on hepatic differentiation of hiPSCs on the PCL-Gel-HA nanofibrous scaffold

Cell therapy and tissue engineering as promising candidates for the liver transplantation dilemma are of special interest. Induced pluripotent stem cells (iPSCs) are one of the best sources in this field, but their differentiation methods to hepatocytes have remained challenging. We transduced human iPSCs (hiPSCs) with miR-122 and off-let-7f (hiPSCs^{miR-122 + off-let-7f} ) to evaluate how they can differentiate hiPSCs to hepatocyte-like cells (HLCs) without any extrinsic growth factor. Additionally, we studied the effect of Poly ɛ-caprolactone-gelatin-hyaluronic acid (PCL-Gel-HA) nanofibrous scaffold as an extracellular matrix (ECM) simulator on differentiation improvement. Definitive endoderm markers (FOXA2 and SOX17), as well as hepatic markers (AFP, Albumin, CK18, HNF4α) expression, were significantly higher in hiPSCs^{miR-122 + off-let-7f} derived HLCs (hiPSCs-HLCs) compared to the control group (miR-scramble transduced hiPSCs: hiPSCs^scramble ). hiPSCs-HLCs indicated hepatocyte morphological characteristics and positive immunostaining for AFP, Albumin and HNF4α. Albumin and urea secretion were significantly higher in hiPSCs-HLCs than hiPSCs^scramble . Comparing these markers in the PCL-Gel-HA group with the tissue culture plate (TCP) group revealed that PCL-Gel-HA could improve differentiation towards HLCs significantly. Regarding our results, these microRNAs can be used to differentiate hiPSCs to the functional hepatocytes for disease modelling, drug screening and cell-based therapy in future studies.

Polycaprolactone-co-polylactic acid nanofiber scaffold in combination with 5-azacytidine and transforming growth factor-β to induce cardiomyocyte differentiation of adipose-derived mesenchymal stem cells

Adipose-derived mesenchymal stem cells (Ad-MSCs) are promising candidates for cardiac repair/regeneration. The application of copolymer nanoscaffolds has received great attention in tissue engineering to support differentiation and functional tissue organization toward effective tissue regeneration. The objective of the current study was to develop functional and bioactive scaffolds by combining polycaprolactone (PCL) and polylactic acid (PLA) for cardiomyocyte differentiation of human Ad-MSC (hAd-MSCs) in the absence or presence of 5-azacytidine and transforming growth factor-β (TGF-β). To that end, the human MSCs were extracted from human adipose tissue (AD). The cardiomyocyte differentiation potency of hAd-MSCs was evaluated on the novel synthetic PCL/PLA nanofiber scaffolds prepared in the absence and presence of 5-azacytidine and TGF-β supplements. A PCL/PLA nanofibrous scaffold was fabricated using the electrospinning method and its nanotopography and porous structure were characterized using scanning electron microscopy. In addition, the attachment of hAd-MSCs on the PCL/PLA scaffolds was semiquantitatively investigated. Compared with other treatments, the PCL/PLA nanofibrous scaffold supplemented with both 5-azacytidine and TGF-β was observed to differentiate hAd-MSCs into cardiomyocytes at Day 21 as evidenced by real-time PCR for cardiac-specific genes including cardiac troponin I (cTnI), GATA4, MYH7, and NKX2.5. In addition, flow cytometric analysis of cTnI-positive cells demonstrated that the cardiomyocyte differentiation of hAd-MSCs was more efficient on the PCL/PLA nanofibrous scaffold supplemented with both 5-azacytidine and TGF-β than it was in the other treatment groups. Generally speaking, the results show that PCL/PLA nanofibrous scaffolds may be applied as a platform for efficient differentiation of hAd-MSCs into functional cardiomyocytes.

Fucoidan-loaded nanofibrous scaffolds promote annulus fibrosus repair by ameliorating the inflammatory and oxidative microenvironments in degenerative intervertebral discs

Tissue engineering holds potential in the treatment of intervertebral disc degeneration (IDD). However, implantation of tissue engineered constructs may cause foreign body reaction and aggravate the inflammatory and oxidative microenvironment of the degenerative intervertebral disc (IVD). In order to ameliorate the adverse microenvironment of IDD, in this study, we prepared a biocompatible poly (ether carbonate urethane) urea (PECUU) nanofibrous scaffold loaded with fucoidan, a natural marine bioactive polysaccharide which has great anti-inflammatory and antioxidative functions. Compared with pure PECUU scaffold, the fucoidan-loaded PECUU nanofibrous scaffold (F-PECUU) decreased the gene and protein expression related to inflammation and the oxidative stress in the lipopolysaccharide (LPS) induced annulus fibrosus cells (AFCs) significantly (p<0.05). Especially, gene expression of Ill 6 and Ptgs2 was decreased by more than 50% in F-PECUU with 3.0 wt% fucoidan (HF-PECUU). Moreover, the gene and protein expression related to the degradation of extracellular matrix (ECM) were reduced in a fucoidan concentration-dependent manner significantly, with increased almost 3 times gene expression of Col1a2 and Acan in HF-PECUU. Further, in a 'box' defect model, HF-PECUU decreased the expression of COX-2 and deposited more ECM between scaffold layers when compared with pure PECUU. The disc height and nucleus pulposus hydration of repaired IVD reached up to 75% and 85% of those in the sham group. In addition, F-PECUU helped to maintain an integrate tissue structure with a similar compression modulus to that in sham group. Taken together, the F-PECUU nanofibrous scaffolds showed promising potential to promote AF repair in IDD treatment by ameliorating the harsh degenerative microenvironment. STATEMENT OF SIGNIFICANCE: Annulus fibrosus (AF) tissue engineering holds potential in the treatment of intervertebral disc degeneration (IDD), but is restricted by the inflammatory and oxidative microenvironment of degenerative disc. This study developed a biocompatible polyurethane scaffold (F-PECUU) loaded with fucoidan, a marine bioactive polysaccharide, for ameliorating IDD microenvironment and promoting disc regeneration. F-PECUU alleviated the inflammation and oxidative stress caused by lipopolysaccharide and prevented extracellular matrix (ECM) degradation in AF cells. In vivo, it promoted ECM deposition to maintain the height, water content and mechanical property of disc. This work has shown the potential of marine polysaccharides-containing functional scaffolds in IDD treatment by ameliorating the harsh microenvironment accompanied with disc degeneration.

Design and Fabrication of a Dual Protein-Based Trilayered Nanofibrous Scaffold for Efficient Wound Healing

Chronic wound healing is a major threat all over the world. There are currently a plethora of biomaterials-based wound dressings available for wound healing applications. In this study, a dual protein-based (silk fibroin and sericin) nanofibrous scaffold from a natural source (B.mori silkworm cocoons) with antibacterial and antioxidative properties for wound healing was investigated. An electrospun layer-by-layer silk protein-based nanofibrous scaffold was fabricated with a top layer of hydrophobic silk fibroin protein blended with polyvinyl alcohol (PVA), a middle layer of waste protein silk sericin loaded with silver(I) sulfadiazine as an antibacterial agent, and a bottom layer using silk fibroin blended with polycaprolactone (PCL). The trilayered nanofibrous scaffold with a smooth and bead-free morphology demonstrated excellent wettability, slow in vitro degradation, controlled drug release, and potent antibacterial and antioxidant properties. In vitro, the scaffold also demonstrated excellent hemocompatibility and biocompatibility. Furthermore, in vivo wound contraction, histological, and micro-CT investigations show complete wound healing and the formation of new skin tissue in a male Balb/c mouse model treated with the scaffold. The antioxidant properties of the sericin protein and SSD-based triple-layered nanofibrous scaffold protect the wound from bacterial infection and improve wound healing in a mouse model. The current study develops a dual protein-based nanofibrous scaffold with antibacterial and antioxidant properties as a promising wound dressing material.

Enhanced neural differentiation of human-induced pluripotent stem cells on aligned laminin-functionalized polyethersulfone nanofibers; a comparison between aligned and random fibers on neurogenesis

Despite the numerous attempts in nerve tissue engineering, no ideal strategy has been translated into effective therapy for neuronal regeneration yet. Here, we designed a novel nerve regeneration scaffold combining aligned laminin-immobilized polyethersulfone (PES) nanofibers and human-induced pluripotent stem cells (hiPSCs) for transplantation strategies. Aligned and random PES nanofibers were fabricated by electrospinning method with a diameter of 95-500 nm and were then modified with covalent laminin bounding subsequent to O₂ plasma treatment. PES-functionalized fibers found to induce a remarkable higher rate of neuronal genes expression as compared to nontreated group. In addition, hiPSCs cultured on aligned pure fibers exhibited the extension of neurites along with fibers direction and an exponentially elevated expression of neuron specific enolase (early neuroectoderm marker), Tuj-1 (axonal marker), and microtubule-associated protein 2 (dendritic marker) in comparison with random pure fibers. The concomitant of increased hydrophilicity and biocompatibility along with exploiting topographical cues and directional guidance make aligned PES-plasma-laminin a versatile scaffold for adhesion, proliferation, spreading, and differentiation of hiPSCs into nerve cells.

The Construction of Multi-Incorporated Polylactic Composite Nanofibrous Scaffold for the Potential Applications in Bone Tissue Regeneration

To improve the bone regeneration ability of pure polymer, varieties of bioactive components were incorporated to a biomolecular scaffold with different structures. In this study, polysilsesquioxane (POSS), pearl powder and dexamethasone loaded porous carbon nanofibers (DEX@PCNFs) were incorporated into polylactic (PLA) nanofibrous scaffold via electrospinning for the application of bone tissue regeneration. The morphology observation showed that the nanofibers were well formed through electrospinning process. The mineralization test of incubation in simulated body fluid (SBF) revealed that POSS incorporated scaffold obtained faster hydroxyapatite depositing ability than pristine PLA nanofibers. Importantly, benefitting from the bioactive components of pearl powder like bone morphogenetic protein (BMP), bone mesenchymal stem cells (BMSCs) cultured on the composite scaffold presented higher proliferation rate. In addition, by further incorporating with DEX@PCNFs, the alkaline phosphatase (ALP) level and calcium deposition were a little higher based on pearl powder. Consequently, the novel POSS, pearl powder and DEX@PCNFs multi-incorporated PLA nanofibrous scaffold can provide better ability to enhance the biocompatibility and accelerate osteogenic differentiation of BMSCs, which has potential applications in bone tissue regeneration.

Osteoblast-derived extracellular matrix coated PLLA/silk fibroin composite nanofibers promote osteogenic differentiation of bone mesenchymal stem cells

Poly-L-lactic acid (PLLA) is one of the most commonly used synthetic materials for regenerative medicine, and silk fibroin (SF) is a natural protein with excellent biocompatibility. Combination of PLLA and SF in a proper proportion by electrospinning may generate composite nanofibers that could meet the requirements of scaffolding in bone tissue engineering. The application of PLLA/SF nanofibrous scaffold for osteogenesis is well established in vitro and in vivo. However, PLLA/SF nanofibrous scaffold does not have an ideal ability to promote cell adhesion, proliferation, and differentiation. Extracellular matrix (ECM) plays a critical role in modulating cellular behavior. However, the role of combination of natural ECM with nanofibrous scaffold in regulating osteogenic differentiation is unclear. In this study, we aimed to develop a novel composite PLLA/SF nanofibrous scaffold coated with osteoblast-derived extracellular matrix (O-ECM/PLLA/SF) and analyze the effects of the modified scaffold on osteogenic differentiation of BMSCs. The surface structural features and compositions of the O-ECM/PLLA/SF scaffold were characterized by SEM and immunofluorescence staining. The capacities of the O-ECM/PLLA/SF scaffold to induce osteogenic differentiation of BMSCs were investigated by alkaline phosphatase (ALP) and alizarin red staining (ARS). The results showed BMSCs cultured on O-ECM/PLLA/SF scaffold significantly increased osteogenic differentiation compared with cells cultured individually on a scaffold or O-ECM. Collectively, these findings indicate that O-ECM-coated nanofibrous scaffold can be a promising strategy for osteogenic differentiation of BMSCs, opening a new possibility of utilizing composite scaffolds for bone tissue engineering.

Multi-Layer Nanofibrous PCL Scaffold-Based Colon Cancer Cell Cultures to Mimic Hypoxic Tumor Microenvironment for Bioassay

Simple Summary

Multi-layer, nanofibrous poly(ε-caprolactone) (PCL) scaffold (pNFS)-based colon cancer cell cultures mimic the hypoxic tumor microenvironment. The simple procedure generates a 3D hypoxic tumor microenvironment comprising defined numbers and densities of colon cancer cells with easily controllable lateral dimensions and a thickness defined by pNFS. This pNFS-based multi-layered colon cancer cell culture system is useful for bioassays, for drug screening, and as a replacement for small animals in testing the effects of a hypoxic tumor microenvironment.

Abstract

Three-dimensional (3D) cancer cell culture systems have been developed to aid the study of molecular mechanisms in cancer development, identify therapeutic targets, and test drug candidates. In this study, we developed a strategy for mimicking the hypoxic tumor microenvironment in a 3D cancer cell culture system using multi-layer, nanofibrous poly(ε-caprolactone) (PCL) scaffold (pNFS)-based cancer cell cultures. We found that human colon cancer cells infiltrated pNFS within 3 days and could be cultured three-dimensionally within the NFS. When incubated in four stacks of 30 µm-thick pNFS for 3 days, colon cancer cells in layer three showed partially reduced entry into the S phase, whereas those in layer four, located farthest from the media, showed a marked reduction in S-phase entry. As a consequence, cells in layer four exhibited hypoxia-induced disorganization of F-actin on day 3, and those in layers three and four showed an increase in the expression of the hypoxia-induced transcription factor HIF-1α and its target genes, Glut1, CA9, VEGF, and LDHA. Consistent with these results, doxorubicin- and ionizing radiation-induced cell death was reduced in colon cancer cells cultured in layers three and four. These results suggest that pNFS-based multi-layer colon cancer cell cultures mimic the hypoxic tumor microenvironment and are useful for bioassays.

Electrospun Scaffolds in Periodontal Wound Healing

Periodontitis is a set of inflammatory conditions affecting the tissues surrounding the teeth predominantly sustained by bacterial infections. The aim of the work was the design and the development of scaffolds based on biopolymers to be inserted in the periodontal pocket to restore tissue integrity and to treat bacterial infections. Nanofibrous scaffolds were prepared by means of electrospinning. Gelatin was considered as base component and was associated to low and high molecular weight chitosans and alginate. The scaffolds were characterized by chemico–physical properties (morphology, solid state-FTIR and differential scanning calorimetry (DSC)-surface zeta potential and contact angle), and mechanical properties. Moreover, preclinical properties (cytocompatibility, fibroblast and osteoblast adhesion and proliferation and antimicrobial properties) were assessed. All the scaffolds were based on cylindrical and smooth nanofibers and preserved their nanofibrous structure upon hydration independently of their composition. They possessed a high degree of hydrophilicity and negative zeta potentials in a physiological environment, suitable surface properties to enhance cell adhesion and proliferation and to inhibit bacteria attachment. The scaffold based on gelatin and low molecular weight chitosan proved to be effective in vitro to support both fibroblasts and osteoblasts adhesion and proliferation and to impair the proliferation of Streptococcus mutans and Aggregatibacter actinomycetemcomitans, both pathogens involved in periodontitis.

Delivery of a mitochondria-targeted antioxidant from biocompatible, polymeric nanofibrous scaffolds

Cardiovascular disease has been associated with increased levels of reactive oxygen species (ROS). Recently, we have shown that a critical balance between cytosolic ROS and mitochondrial ROS is crucial in cardiovascular health and that modulation of mitochondrial ROS helps prevent detrimental effects of cytosolic ROS on endothelial cells (EC) in transgenic animals. Here, we report the development of a controlled delivery system for a mitochondria‐targeted antioxidant, JP4‐039, from an electrospun scaffold made of FDA‐approved biocompatible polymeric nanofibers. We demonstrate that the active antioxidant moiety was preserved in released JP4‐039 for over 72 h using electron paramagnetic resonance. We also show that both the initial burst release of the drug within the first 20 min and the ensuing slow and sustained release that occurred over the next 24 h improved tube formation in human coronary artery ECs (HCAEC) in vitro. Taken together, these findings suggest that electrospinning methods can be used to upload mitochondrial antioxidant (JP4‐039) onto a biocompatible nanofibrous PLGA scaffold, and the uploaded drug (JP4‐039) retains nitroxide antioxidant properties upon release from the scaffold, which in turn can reduce mitochondrial ROS and improve EC function in vitro.

Regeneration of the peripheral nerve via multifunctional electrospun scaffolds

Over the last two decades, electrospun scaffolds have proved to be advantageous in the field of nerve tissue regeneration by connecting the cavity among the proximal and distal nerve stumps growth cones and leading to functional recovery after injury. Multifunctional nanofibrous structure of these scaffolds provides enormous potential by combining the advantages of nano-scale topography, and biological science. In these structures, selecting the appropriate materials, designing an optimized structure, modifying the surface to enhance biological functions and neurotrophic factors loading, and native cell-like stem cells should be considered as the essential factors. In this systematic review paper, the fabrication methods for the preparation of aligned nanofibrous scaffolds in yarn or conduit architecture are reviewed. Subsequently, the utilized polymeric materials, including natural, synthetic and blend are presented. Finally, their surface modification techniques, as well as, the recent advances and outcomes of the scaffolds, both in vitro and in vivo, are reviewed and discussed.

Novel three-dimensional bioglass functionalized gelatin nanofibrous scaffolds for bone regeneration

The clinical use of FDA-approved bone morphogenetic proteins (BMPs) are impeded by high costs, super-high dosage requirement, short half-life, and other undesirable side effects. Therefore, designing a biomaterial that can promote new bone formation without using exogenous BMPs is highly desirable in clinical applications. In the present work, a new kind of nanofibrous scaffold composed of gelatin and 45S5 bioglass (GF/45S5 BG) was prepared through thermally induced phase separation method together with the particle leach technique (TIPS&P). In addition to the significantly higher mechanical strength, the composite scaffolds (GF/45S5 BG) significantly increased osteogenic differentiation of human mesenchymal stem cells (hMSCs) in vitro compared with the neat scaffold (GF) without adding other biological agents, for example, BMPs or hormones. Most importantly, our in vivo studies also indicated that GF/45S5 BG scaffolds could directly promote ectopic bone regeneration in SD rats without exogenous BMP2. In summary, both in vitro and in vivo results indicated that the novel 45S5 bioglass functionalized GF nanofibrous scaffold is a promising alternative for bone tissue engineering.

Soy Protein Nanofiber Scaffolds for Uniform Maturation of Human Induced Pluripotent Stem Cell-Derived Retinal Pigment Epithelium

Retinal pigment epithelium (RPE) differentiated from human induced pluripotent stem cells, called induced retinal pigment epithelium (iRPE), is being explored as a cell-based therapy for the treatment of retinal degenerative diseases, especially age-related macular degeneration. The success of RPE implantation is linked to the use of biomimetic scaffolds that simulate Bruch's membrane and promote RPE maturation and integration as a functional tissue. Due to difficulties associated with animal protein-derived scaffolds, including sterility and pro-inflammatory responses, current practices favor the use of synthetic polymers, such as polycaprolactone (PCL), for generating nanofibrous scaffolds. In this study, we tested the hypothesis that plant protein-derived fibrous scaffolds can provide favorable conditions permissive for the maturation of RPE tissue sheets in vitro. Our natural, soy protein-derived nanofibrous scaffolds exhibited a J-shaped stress-strain curve that more closely resembled the mechanical properties of native tissues than PCL with significantly higher hydrophilicity of the natural scaffolds, favoring in vivo implantation. We then demonstrate that iRPE sheets growing on these soy protein scaffolds are equivalent to iRPE monolayers cultured on synthetic PCL nanofibrous scaffolds. Immunohistochemistry demonstrated RPE-like morphology and functionality with appropriate localization of RPE markers RPE65, PMEL17, Ezrin, and ZO1 and with anticipated histotypic polarization of vascular endothelial growth factor and pigment epithelium-derived growth factor as indicated by enzyme-linked immunosorbent assay. Scanning electron microscopy revealed dense microvilli on the cell surface and homogeneous tight junctional contacts between the cells. Finally, comparative transcriptome analysis in conjunction with principal component analysis demonstrated that iRPE on nanofibrous scaffolds, either natural or synthetic, matured more consistently than on nonfibrous substrates. Taken together, our studies suggest that the maturation of cultured iRPE sheets for subsequent clinical applications might benefit from the use of nanofibrous scaffolds generated from natural proteins. Impact statement Induced retinal pigment epithelium (iRPE) from patient-derived induced pluripotent stem cells (iPSCs) may yield powerful treatments of retinal diseases, including age-related macular degeneration. Recent studies, including early human clinical trials, demonstrate the importance of selecting appropriate biomaterial scaffolds to support tissue-engineered iRPE sheets during implantation. Electrospun scaffolds show particular promise due to their similarity to the structure of the native Bruch's membrane. In this study, we describe the use of electroprocessed nanofibrous soy protein scaffolds to generate polarized sheets of human iPSC-derived iRPE sheets. Our evaluation, including RNA-seq transcriptomics, indicates that these scaffolds are viable alternatives to scaffolds electrospun from synthetic polymers.

The effect of surface modification of poly-lactide-co-glycolide/carbon nanotube nanofibrous scaffolds by laminin protein on nerve tissue engineering

The presence of biological cues to promote the attachment, proliferation, and differentiation of neuronal cells is important in the process of nerve regeneration. In this study, laminin as a neurite promoting protein, has been used to modify poly-lactide-co-glycolide/carbon nanotube (PLGA/CNT) electrospun nanofibrous scaffolds by means of either mussel-inspired poly(dopamine) (PD) coating or via direct physical adsorption as a simple route for the functionalization of biomaterials. The laminin-modified scaffolds were characterized by a combination of field emission scanning electron microscopy (SEM), X-ray photoelectron spectroscopy, and contact angle measurements. Subsequently, various properties of scaffolds such as degradation time, amount of attached laminin and the rate of CNT release were investigated. The synergistic effect of topographical and biological cues for PC12 cell attachment, proliferation, and differentiation were then studied by SEM and confocal microscopy. The results of degradation study showed that laminin-modified scaffolds were biodegradable with good structural integrity that persisted about 4 weeks. The amount of laminin attached to the PLGA/CNT and PLGA/CNT-PD scaffolds was 3.12 ± 0.6 and 3.04 ± 071 μg per mg of the scaffold, respectively. Although laminin-modified scaffolds could improve cell proliferation identically, neurite extensions on the PLGA/CNT scaffold modified via PD coating (PLGA/CNT-PD-lam scaffold) were significantly longer than those observed on PLGA/CNT scaffold modified via physical adsorption (PLGA/CNT-lam scaffold) and unmodified scaffolds. Together, these results indicated that surface modification via PD coating could be a promising strategy to fabricate biomimetic scaffolds capable of sustaining longer neuronal growth for nerve tissue engineering.

Co-Culturing of Endothelial and Cancer Cells in a Nanofibrous Scaffold-Based Two-Layer System

Angiogenesis is critical for local tumor growth. This study aimed to develop a three-dimensional two-layer co-culture system to investigate effects of cancer cells on the growth of endothelial cells (ECs). Poly(ε-caprolactone) (PCL) nanofibrous membranes were generated via electrospinning of PCL in chloroform (C-PCL-M) and chloroform and dimethylformamide (C/DMF-PCL-M). We assembled a two-layer co-culture system using C-PCL-M and C/DMF-PCL-M for EC growth in the upper layer with co-cultured cancer cells in the lower layer. In the absence of vascular endothelial growth factor (VEGF), growth of bEND.3 ECs decreased on C/DMF-PCL-M but not on C-PCL-M with time. Growth of bEND.3 cells on C/DMF-PCL-M was enhanced through co-culturing of CT26 cancer cells and enhanced growth of bEND.3 cells was abrogated with anti-VEGF antibodies and sorafenib. However, EA.hy926 ECs displayed steady growth and proliferation on C/DMF-PCL-M, and their growth was not further increased through co-culturing of cancer cells. Moreover, chemical hypoxia in CT26 cancer cells upon treatment with CoCl₂ enhanced the growth of co-cultured bEND.3 cells in the two-layer system. Thus, EC growth on the nanofibrous scaffold is dependent on the types of ECs and composition of nanofibers and this co-culture system can be used to analyze EC growth induced by cancer cells.

Induction of Hepatic Regeneration in an Experimental Model Using Hepatocyte-Differentiated Mesenchymal Stem Cells

Mesenchymal stem cell (MSC)-based liver tissue engineering on nanofibrous scaffold holds great promise for cell-based therapy in liver injuries and end-stage liver failure treatments. MSCs were generated from umbilical cord blood. Hepatogenic differentiation was induced on two-dimensional (2D) and three-dimensional (3D) culture system and characterized by morphology, scanning electron microscopy, immunocytochemistry, and gene expression. Albumin and α-1 antitrypsin (AAT) in culture supernatants were measured. Differentiated cells were administered intravenous into a murine model of carbon tetra induced liver cirrhosis. After 12 weeks of injection, liver pathology was examined. The hepatogenic differentiated MSCs stained positively for albumin, alpha fetoprotein, HepPar1, cytokeratin 7 and 18, and OV6 with more mature cells, hexagonal in shape with central nuclei forming large sheets in groups in 3D culture system. AAT secretion and indocyanine green uptake were significantly increased in 3D system. In experimental model, MSC-3D treated group exhibited maximal restoration of liver architecture with absent septal fibrosis and marked improvement of alanine transaminase (ALT) and aspartate transaminase (AST), and mild increase in albumin. Both 3D and 2D culture system are effective in functional hepatogenic differentiation from MSCs and serve as a vehicle in liver tissue engineering. In vivo hepatogenic differentiation is more effective on 3D scaffold, with better functional recovery.

Anti-inflammatory activity of emu oil-based nanofibrous scaffold through downregulation of IL-1, IL-6, and TNF-α pro-inflammatory cytokines

Background Inflammation is one of the most important responses of the body against infection or disease, and it protects tissues from injury; however, it causes redness, swelling, pain, fever and loss of function. The aim of this present study was to evaluate the anti-inflammatory activity of emu oil (Eu) formulated nanofibrous scaffold in HFFF2 fibroblast cells. Materials and methods Eu was formulated successfully in nanofibers through the electrospinning method. Besides, the morphological and structural properties of Eu nanofibres were evaluated using Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The MTT assay (3-[4,5-dimethylthiazol-2-yl]-2,5-diphenyl tetrazolium bromide) was performed to evaluate the HFFF2 fibroblast cells' viability. Also, real-time polymerase chain reaction (PCR) was used to evaluate the anti-inflammatory signaling pathway in treated HFFF2 cells with Eu nanofiber. Results Our study showed that the Eu nanofiber increased the viability of fibroblast HFFF2 cells (p < 0.05). Also, the expression of interleukin1 (IL1), IL6 and tumor necrosis factor- alpha (TNF-α) pro-inflammatory cytokines genes were significantly decreased in treated HFFF2 cells with Eu nanofiber (p < 0.05). Conclusions In conclusion, Eu nanofiber scaffold potentially can reduce the inflammation process through downregulation of IL-1, IL-6 and TNF-α cytokines.

Bilayered Scaffold Prepared from a Kartogenin-Loaded Hydrogel and BMP-2-Derived Peptide-Loaded Porous Nanofibrous Scaffold for Osteochondral Defect Repair

Recently, a bilayered scaffold with an anisotropic structure mimicking a native osteochondral tissue shows considerable potential for treating osteochondral defects. Herein, a bilayered scaffold consisting of biomimetic cartilage and a subchondral bone architecture was constructed for repairing osteochondral defect. A hydrogel prepared by the Schiff base reaction of gelatin, silk fibroin, and oxidized dextran was designed as the cartilage layer, while a nanofibrous scaffold with a macroporous structure prepared from the polymer blend of poly(l-lactic acid)/poly(lactic-co-glycolic acid)/poly(ε-caprolactone) using the dual phase separation technique served as a subchondral layer. The subchondral layer was then treated with polydopamine coating for osteogenic factor immobilization. To facilitate the chondrogenic and osteogenic differentiation of bone marrow mesenchymal stem cells on the bilayered scaffold, the cartilage-inducing drug kartogenin (KGN) and osteogenic-inducing factor bone morphogenetic protein 2-derived peptides (P24 peptides) were, respectively, loaded on the subchondral layer. Next, the in vitro release of KGN and P24 peptide from the corresponding layer was monitored, respectively, and the results showed that both the release time of KGN and P24 peptides would last for more than 28 days. The in vitro results indicated that the KGN-loaded cartilage layer and P24 peptides-loaded subchondral layer were capable of supporting cell proliferation, and induced the chondrogenic and osteogenic differentiation, respectively. Furthermore, the in vivo experiments suggested that the bilayered scaffold significantly accelerated the regeneration of the osteochondral tissue in the rabbit knee joint model. Consequently, this bilayered scaffold loaded with KGN and P24 peptides would be a promising candidate for repairing osteochondral defect.

Comparison of osteogenic differentiation potential of induced pluripotent stem cells on 2D and 3D polyvinylidene fluoride scaffolds

In recent decades, tissue engineering has been the most contributor for introducing 2D and 3D biocompatible osteoinductive scaffolds as bone implants. Polyvinylidene fluoride (PVDF), due to the unique mechanical strength and piezoelectric properties, can be a good choice for making a bone bioimplant. In the present study, PVDF nanofibers and film were fabricated as 3D and 2D scaffolds, and then, osteogenic differentiation potential of the human induced pluripotent stem cells (iPSCs) was investigated when grown on the scaffolds by evaluating the common osteogenic markers in comparison with tissue culture plate. Biocompatibility of the fabricated scaffolds was confirmed qualitatively and quantitatively by the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide and scanning electron microscopy assays. Human iPSCs cultured on PVDF nanofibers showed a significantly higher alkaline phosphate activity and calcium content compared with the iPSCs cultured on PVDF film. Osteogenic-related genes and proteins were also expressed in the iPSCs seeded on PVDF nanofibers significantly higher than iPSCs seeded on PVDF film, when investigated by real-time reverse transcription polymerase chain reaction and western blot analysis, respectively. According to the results, the PVDF nanofibrous scaffold showed a greater osteoinductive property compared with the PVDF film and due to the material similarity of the scaffolds, it could be concluded that the 3D structure could lead to better bone differentiation. Taken together, the obtained results demonstrated that human iPSC-seeded PVDF nanofibrous scaffold could be considered as a promising candidate for use in bone tissue engineering applications.

Graphene Oxide Immobilized PLGA-polydopamine Nanofibrous Scaffolds for Growth Inhibition of Colon Cancer Cells

Graphene oxide (GO)/poly (lactide-co-glycolic acid) (PLGA) scaffolds have promising applications in the biomedical field. However, greater attention is focused on the incorporated system and its applications in normal cells. In this work, a novel GO immobilized PLGA nanofibrous scaffold assisted by polydopamine (PLGA-PDA-GO) is developed for growth inhibition of HT-29 colon cancer cells. The interactions between GO and PDA are attributed to a π-π conjugate interaction and electrostatic attraction. In addition to the enhancement of thermal stability and mechanical strength, the surface roughness, hydrophilicity, and electro-activity of the scaffolds are significantly improved by immobilization of GO. The scaffolds show good inhibition of HT-29, and immobilized GO is observed to be in contact with but not internalized in HT-29 cells. The cytotoxicity mechanism of scaffolds toward HT-29 is attributed to intracellular activated reactive oxygen species that result from the physical interaction of the sharp GO edges and electrical signals of π-π stacking between PDA and GO.

Therapeutic potential of human mesenchymal stem cells derived beta cell precursors on a nanofibrous scaffold: An approach to treat diabetes mellitus

Diabetes mellitus is an autoimmune and chronic disorder that is rapidly expanding worldwide due to increasing obesity. In the current study, we were able to design a reliable 3-dimensional differentiation process of human Wharton's jelly mesenchymal stem cells into pancreatic beta cell precursors (PBCPs) and detected that transplanted PBCPs could improve hyperglycemia in a diabetes-induced model in mice. Polylactic acid/chitosan nanofibrous scaffold was prepared using an electrospinning method. Quantitative real-time reverse transcription-polymerase chain reaction and immunocytochemistry analysis were carried out to assess pancreatic marker expression in the differentiated cells. PBCPs were transplanted under the kidney capsule of diabetic mice that induced streptozotocin injection 14 days before the transplantation. Moreover, an intraperitoneal glucose tolerance test (ipGTT) was carried out 2 and 4 weeks after the transplantation to measure the reaction to a sudden increase of the blood glucose level in the transplanted animals. The results indicated that the expression of SRY (sex determining region Y)-box (Sox17), forkhead box A2 (FoxA2), pancreatic and duodenal homeobox 1 (Pdx1), neurogenin 3 (Ngn3), hepatic nuclear factor 4, alpha (Hnf4α), and NK2 homeobox 2 (Nkx2.2) were increased significantly in the differentiated cells compared with that of the control group. In the current study, the diabetic disease was confirmed by measuring blood glucose and proved by conducting some other behavioral tests. After the PBCPs transplantation in a diabetic model, the ipGTT and hyperglycemia investigation during the determinant times confirmed the disease's significant improvement in the experimental models. In this study, some preclinical data suggested that the transplantation of PBCPs associated with appropriate nanofiber scaffold can be utilized for the treatment of diabetes models. In addition, studies are required to elucidate the molecular mechanism of PBCPs acting in diabetes models before being used for patients with diabetes.

Matrix stiffness modulates the differentiation of neural crest stem cells in vivo

Stem cells are often transplanted with scaffolds for tissue regeneration; however, how the mechanical property of a scaffold modulates stem cell fate in vivo is not well understood. Here we investigated how matrix stiffness modulates stem cell differentiation in a model of vascular graft transplantation. Multipotent neural crest stem cells (NCSCs) were differentiated from induced pluripotent stem cells, embedded in the hydrogel on the outer surface of nanofibrous polymer grafts, and implanted into rat carotid arteries by anastomosis. After 3 months, NCSCs differentiated into smooth muscle cells (SMCs) near the outer surface of the polymer grafts; in contrast, NCSCs differentiated into glial cells in the most part of the hydrogel. Atomic force microscopy demonstrated a stiffer matrix near the polymer surface but much lower stiffness away from the polymer graft. Consistently, in vitro studies confirmed that stiff surface induced SMC genes whereas soft surface induced glial genes. These results suggest that the scaffold's mechanical properties play an important role in directing stem cell differentiation in vivo, which has important implications in biomaterials design for stem cell delivery and tissue engineering.

Prevascularization of natural nanofibrous extracellular matrix for engineering completely biological three-dimensional prevascularized tissues for diverse applications

Self-sustainability after implantation is one of the critical obstacles facing large engineered tissues. A preformed functional vascular network provides an effective solution for solving the mass transportation problem. With the support of mural cells, endothelial cells (ECs) can form microvessels within engineered tissues. As an important mural cell, human mesenchymal stem cells (hMSCs) not only stabilize the engineered microvessel network, but also preserve their multi-potency when grown under optimal culture conditions. A prevascularized hMSC/extracellular matrix (ECM) sheet fabricated by the combination of hMSCs, ECs and a naturally derived nanofibrous ECM scaffold offers great opportunity for engineering mechanically strong and completely biological three-dimensional prevascularized tissues. The objective of this study was to create a prevascularized hMSC/ECM sheet by co-culturing ECs and hMSCs on a nanofibrous ECM scaffold. Physiologically low oxygen (2% O2 ) was introduced during the 7 day hMSC culture to preserve the stemness of hMSCs and thereby their capability to secrete angiogenic factors. The ECs were then included to form microvessels under normal oxygen (20% O2 ) for up to 7 days. The results showed that a branched and mature vascular network was formed in the co-culture condition. Angiogenic factors vascular endothelial growth factor (VEGF), basic fibroblast growth factor (bFGF) and angiopoietin-1 (Ang-1) were significantly increased by low-oxygen culture of hMSCs, which further stabilized and supported the maturation of microvessels. A differentiation assay of the prevascularized ECM scaffold demonstrated a retained hMSC multi-potency in the hypoxia cultured samples. The prevascularized hMSC/ECM sheet holds great promise for engineering three-dimensional prevascularized tissues for diverse applications.

Engineering of Corneal Tissue through an Aligned PVA/Collagen Composite Nanofibrous Electrospun Scaffold

Corneal diseases are the main reason of vision loss globally. Constructing a corneal equivalent which has a similar strength and transparency with the native cornea, seems to be a feasible way to solve the shortage of donated cornea. Electrospun collagen scaffolds are often fabricated and used as a tissue-engineered cornea, but the main drawback of poor mechanical properties make it unable to meet the requirement for surgery suture, which limits its clinical applications to a large extent. Aligned polyvinyl acetate (PVA)/collagen (PVA-COL) scaffolds were electrospun by mixing collagen and PVA to reinforce the mechanical strength of the collagen electrospun scaffold. Human keratocytes (HKs) and human corneal epithelial cells (HCECs) inoculated on aligned and random PVA-COL electrospun scaffolds adhered and proliferated well, and the aligned nanofibers induced orderly HK growth, indicating that the designed PVA-COL composite nanofibrous electrospun scaffold is suitable for application in tissue-engineered cornea.

[Effect of silk fibroin/poly ( L-lactic acid-co-e-caprolactone) nanofibrous scaffold on tendon-bone healing of rabbits]

Objective

To explore the effect of silk fibroin/poly( L-lactic acid-co-e-caprolactone) [SF/P(LLA-CL)] nanofibrous scaffold on tendon-bone healing of rabbits.

Methods

SF/P(LLA-CL) nanofibrous scaffold was fabricated by electrospinning methods. The morphology of the scaffold was observed by scanning electron microscope (SEM). Pre-osteoblasts MC3T3-E1 cells were seeded on the scaffold and cultured for 1, 3, and 5 days. Cell adhesion and proliferation were also observed by SEM. Meanwhile, twenty-four New Zealand white rabbits were randomly divided into the autogenous tendon group (control group) and the autogenous tendon wrapped with SF/P(LLA-CL) scaffold group (experimental group), with twelve rabbits in each group. An extra-articular model was established, the effect was evaluated by histological examination and mechanical testing.

Results

The morphology of SF/P(LLA-CL) nanofibrous scaffold was random, with a diameter of (219.4±66.5) nm. SEM showed that the MC3T3-E1 cells seeded on the scaffold were in the normal shape, growing well, and proliferating with time course. The results of histological examination showed that inflammatory cells infltrated into the graft-host bone interface at 6 weeks after operation in both groups. Besides, the width of interface showed no significant difference between groups. At 12 weeks after operation, protruding new bone tissue could be observed at the interface in the experimental group, while scar tissue but no new bone tissue could be seen at the interface in the control group. Mechanical testing showed that there was no significant difference in the failure load and the stiffness between groups at 6 weeks after operation ( P>0.05). The failure load and the stiffness in the experimental group were significantly higher than those in the control group at 12 weeks after operation ( P<0.05).

Conclusion

The SF/P(LLA-CL) nanofibrous scaffold has good cell biocompatibility and can effectively promote tendon-bone healing, thus providing new method for modifying graft for ACL reconstruction in the clinical practice.

A review of fibrin and fibrin composites for bone tissue engineering

Tissue engineering has emerged as a new treatment approach for bone repair and regeneration seeking to address limitations associated with current therapies, such as autologous bone grafting. While many bone tissue engineering approaches have traditionally focused on synthetic materials (such as polymers or hydrogels), there has been a lot of excitement surrounding the use of natural materials due to their biologically inspired properties. Fibrin is a natural scaffold formed following tissue injury that initiates hemostasis and provides the initial matrix useful for cell adhesion, migration, proliferation, and differentiation. Fibrin has captured the interest of bone tissue engineers due to its excellent biocompatibility, controllable biodegradability, and ability to deliver cells and biomolecules. Fibrin is particularly appealing because its precursors, fibrinogen, and thrombin, which can be derived from the patient's own blood, enable the fabrication of completely autologous scaffolds. In this article, we highlight the unique properties of fibrin as a scaffolding material to treat bone defects. Moreover, we emphasize its role in bone tissue engineering nanocomposites where approaches further emulate the natural nanostructured features of bone when using fibrin and other nanomaterials. We also review the preparation methods of fibrin glue and then discuss a wide range of fibrin applications in bone tissue engineering. These include the delivery of cells and/or biomolecules to a defect site, distributing cells, and/or growth factors throughout other pre-formed scaffolds and enhancing the physical as well as biological properties of other biomaterials. Thoughts on the future direction of fibrin research for bone tissue engineering are also presented. In the future, the development of fibrin precursors as recombinant proteins will solve problems associated with using multiple or single-donor fibrin glue, and the combination of nanomaterials that allow for the incorporation of biomolecules with fibrin will significantly improve the efficacy of fibrin for numerous bone tissue engineering applications.

Braided and Stacked Electrospun Nanofibrous Scaffolds for Tendon and Ligament Tissue Engineering

Tendon and ligament injuries are a persistent orthopedic challenge given their poor innate healing capacity. Nonwoven electrospun nanofibrous scaffolds composed of polyesters have been used to mimic the mechanics and topographical cues of native tendons and ligaments. However, nonwoven nanofibers have several limitations that prevent broader clinical application, including poor cell infiltration, as well as tensile and suture-retention strengths that are inferior to native tissues. In this study, multilayered scaffolds of aligned electrospun nanofibers of two designs-stacked or braided-were fabricated. Mechanical properties, including structural and mechanical properties and suture-retention strength, were determined using acellular scaffolds. Human bone marrow-derived mesenchymal stem cells (MSCs) were seeded on scaffolds for up to 28 days, and assays for tenogenic differentiation, histology, and biochemical composition were performed. Braided scaffolds exhibited improved tensile and suture-retention strengths, but reduced moduli. Both scaffold designs supported expression of tenogenic markers, although the effect was greater on braided scaffolds. Conversely, cell infiltration was superior in stacked constructs, resulting in enhanced cell number, total collagen content, and total sulfated glycosaminoglycan content. However, when normalized against cell number, both designs modulated extracellular matrix protein deposition to a similar degree. Taken together, this study demonstrates that multilayered scaffolds of aligned electrospun nanofibers supported tenogenic differentiation of seeded MSCs, but the macroarchitecture is an important consideration for applications of tendon and ligament tissue engineering.

Carbon Nanofiber/Polycaprolactone/Mineralized Hydroxyapatite Nanofibrous Scaffolds for Potential Orthopedic Applications

Hydroxyapatite (Ca₁₀ (PO₄)₆(OH)₂, HAP), a multimineral substituted calcium phosphate is one of the most substantial bone mineral component that has been widely used as bone replacement materials because of its bioactive and biocompatible properties. However, the use of HAP as bone implants is restricted due to its brittle nature and poor mechanical properties. To overcome this defect and to generate suitable bone implant material, HAP is combined with biodegradable polymer (polycaprolactone, PCL). To enhance the mechanical property of the composite, carbon nanofibers (CNF) is incorporated to the composite, which has long been considered for hard and soft tissue implant due to its exceptional mechanical and structural properties. It is well-known that nanofibrous scaffold are the most-prominent material for the bone reconstruction. We have developed a new remarkable CNF/PCL/mineralized hydroxyapatite (M-HAP) nanofibrous scaffolds on titanium (Ti). The as-developed coatings were characterized by various techniques. The results indicate the formation and homogeneous distribution of components in the nanofibrous scaffolds. Incorporation of CNF into the PCL/M-HAP composite significantly improves the adhesion strength and elastic modulus of the scaffolds. Furthermore, the responses of human osteosarcoma (HOS MG63) cells cultured onto the scaffolds demonstrate that the viability of cells were considerably high for CNF-incorporated PCL/M-HAP than for PCL/M-HAP. In vivo analysis show the presence of soft fibrous tissue growth without any significant inflammatory signs, which suggests that incorporated CNF did not counteract the favorable biological roles of HAP. For load-bearing applications, research in various bone models is needed to substantiate the clinical availability. Thus, from the obtained results, we suggest that CNF/PCL/M-HAP nanofibrous scaffolds can be considered as potential candidates for orthopedic applications.

Hypoxia-Mimicking Nanofibrous Scaffolds Promote Endogenous Bone Regeneration

Utilizing biomimetic materials to potentiate endogenous cell growth or signaling is superior to relying on exogenous cells or signals for bone formation. Desferoxamine (DFO), which is a hypoxia-mimetic agent that chelates iron (Fe³⁺), mimics hypoxia to encourage bone healing. However, high cytotoxicity, off-target effects, and the short half-life of DFO have significantly impeded its further applications. We mitigated these side effects by locally immobilizing DFO onto a gelatin nanofibrous (GF) scaffold that retained DFO's ability to chelate Fe³⁺. Moreover, DFO-functionalized GF (GF-DFO) scaffolds, which have similar micro/macrostructures to GF scaffolds, not only demonstrated decreased cytotoxicity on both human umbilical vein endothelial cells and human mesenchymal stem cells but also significantly increased vascular endothelial growth factor (VEGF) expression in vitro. Most importantly, in our in vivo experiments on a critical-sized cranial bone defect mouse model, a significant amount of bone was formed in most of the GF-DFO scaffolds after six weeks, while very little new bone was observed in the GF scaffolds. These data suggest that use of a hypoxia-mimicking nanofibrous scaffold is a promising strategy for promoting endogenous bone formation.

Electrospun Scaffolds for Corneal Tissue Engineering: A Review

Corneal diseases constitute the second leading cause of vision loss and affect more than 10 million people globally. As there is a severe shortage of fresh donated corneas and an unknown risk of immune rejection with traditional heterografts, it is very important and urgent to construct a corneal equivalent to replace pathologic corneal tissue. Corneal tissue engineering has emerged as a practical strategy to develop corneal tissue substitutes, and the design of a scaffold with mechanical properties and transparency similar to that of natural cornea is paramount for the regeneration of corneal tissues. Nanofibrous scaffolds produced by electrospinning have high surface area-to-volume ratios and porosity that simulate the structure of protein fibers in native extra cellular matrix (ECM). The versatilities of electrospinning of polymer components, fiber structures, and functionalization have made the fabrication of nanofibrous scaffolds with suitable mechanical strength, transparency and biological properties for corneal tissue engineering feasible. In this paper, we review the recent developments of electrospun scaffolds for engineering corneal tissues, mainly including electrospun materials (single and blended polymers), fiber structures (isotropic or anisotropic), functionalization (improved mechanical properties and transparency), applications (corneal cell survival, maintenance of phenotype and formation of corneal tissue) and future development perspectives.

Three-dimensional culture and interaction of cancer cells and dendritic cells in an electrospun nano-submicron hybrid fibrous scaffold

An artificial three-dimensional (3D) culture system that mimics the tumor microenvironment in vitro is an essential tool for investigating the cross-talk between immune and cancer cells in tumors. In this study, we developed a 3D culture system using an electrospun poly(ε-caprolactone) (PCL) nanofibrous scaffold (NFS). A hybrid NFS containing an uninterrupted network of nano- and submicron-scale fibers (400 nm to 2 µm) was generated by deposition onto a stainless steel mesh instead of an aluminum plate. The hybrid NFS contained multiplanar pores in a 3D structure. Surface-seeded mouse CT26 colon cancer cells and bone marrow-derived dendritic cells (BM-DCs) were able to infiltrate the hybrid NFS within several hours. BM-DCs cultured on PCL nanofibers showed a baseline inactive form, and lipopolysaccharide (LPS)-activated BM-DCs showed increased expression of CD86 and major histocompatibility complex Class II. Actin and phosphorylated FAK were enriched where unstimulated and LPS-stimulated BM-DCs contacted the fibers in the 3D hybrid NFS. When BM-DCs were cocultured with mitoxantrone-treated CT26 cells in a 3D hybrid NFS, BM-DCs sprouted cytoplasm to, migrated to, synapsed with, and engulfed mitoxantrone-treated CT26 cancer cells, which were similar to the naturally occurring cross-talk between these two types of cells. The 3D hybrid NFS developed here provides a 3D structure for coculture of cancer and immune cells.

Electrospun mat with eyelid fat-derived stem cells as a scaffold for ocular epithelial regeneration

The aim of this study was to develop nanofibrous gelatin substrates for eyelid fat stem cell (EFSC) expansion that can serve as a potential alternative substrate to replace human amniotic membrane. Biocompatibility results indicated that all substrates were highly biocompatible, as EFSCs could favorably attach and proliferate on the nanofibrous surfaces. Microscopic figures showed that the EFSC were firmly anchored to the substrates and were able to retain a normal stem cell phenotype. Immunocytochemistry (ICC) and real time-PCR results revealed change in the expression profile of EFSCs grown on nanofibrous substrates when compared to those grown on control in epithelial induction condition. In addition, electrospun gelatin mats especially oriented scaffold provides not only a milieu supporting EFSCs expansion, but also serves as a useful alternative carrier for ocular surface tissue engineering and could be used as an alternative substrate to amniotic membrane.

Bacterial Cellulose-Based Biomimetic Nanofibrous Scaffold with Muscle Cells for Hollow Organ Tissue Engineering

In this study, we built a bilayer nanofibrous material by utilizing the gelatinization properties of potato starch (PS) to interrupt bacterial cellulose (BC) assembly during static culture to create more free spaces within the fibrous network. Then, muscle cells were cultured on the loose surface of the BC/PS scaffolds to build biomaterials for hollow organ reconstruction. Our results showed that the BC/PS scaffolds exhibited similar mechanical characters to those in the traditional BC scaffolds. And the pore sizes and porosities of BC/PS scaffolds could be controlled by adjusting the starch content. The average nanofiber diameters of unmodified BC and BC/PS composites is approximately to that of the urethral acellular matrix. Those scaffolds permit the muscle cells infiltration into the loose layer and the BC/PS membranes with muscle cells could enhance wound healing in vivo and vitro. Our study suggested that the use of bilayer BC/PS nanofibrous scaffolds may lead to improved vessel formation. BC/PS nanofibrous scaffolds with muscle cells enhanced the repair in dog urethral defect models, resulting in patent urethra. Improved organized muscle bundles and epithelial layer were observed in animals treated with BC/PS scaffold seeded by muscle cells compared with those treated with pure BC/PS scaffold. This study suggests that this biomaterial could be suitable for tissue engineered urinary tract reconstruction and this type of composite scaffold could be used for numerous other types of hollow organ tissue engineering grafts, including vascular, bladder, ureter, esophagus, and intestine.

Peptide Bioink: Self-Assembling Nanofibrous Scaffolds for Three-Dimensional Organotypic Cultures

Printable scaffolds with adequate mechanical strength and stiffness are sought after to ensure viability of printed cells and tissues. We report the first peptide bioinks-lysine-containing hexapeptides that self-assemble into stable, nanofibrous three-dimensional hydrogels with unprecedented stiffness of up to 40 kPa. These biocompatible scaffolds support the three-dimensional culture of human stem cells and differentiation of primary cells into organotypic (gastrointestinal and skin) structures for high-throughput screening, diagnosis, and tissue engineering.

An update on clinical applications of electrospun nanofibers for skin bioengineering

Mimicking morphological similarities of the natural extra cellular matrix (ECM), described by ultrafine continuous fibers, high surface to volume ratio, and high porosity is valuable for effective regeneration of injured skin tissue. Electrospun nanofibers, being one of the most favorable and fast developing products of technology today, display a tremendous potential in wound healing and skin tissue engineering. Under the remarkable attention being given to electrospun nanofibrous scaffolds in promoting wound healing and skin regeneration, this review focuses on the potential of the electrospinning technique as a promising tool for constructing polymeric nanofibrous scaffolds with the favorable physicochemical properties needed for skin bioengineering. In addition, current applications of electrospun nanofibrous matrices for skin bioengineering are detailed in this review.

Thickness-controllable electrospun fibers promote tubular structure formation by endothelial progenitor cells

Controlling the thickness of an electrospun nanofibrous scaffold by altering its pore size has been shown to regulate cell behaviors such as cell infiltration into a three-dimensional (3D) scaffold. This is of great importance when manufacturing tissue-engineering scaffolds using an electrospinning process. In this study, we report the development of a novel process whereby additional aluminum foil layers were applied to the accumulated electrospun fibers of an existing aluminum foil collector, effectively reducing the incidence of charge buildup. Using this process, we fabricated an electrospun scaffold with a large pore (pore size >40 μm) while simultaneously controlling the thickness. We demonstrate that the large pore size triggered rapid infiltration (160 μm in 4 hours of cell culture) of individual endothelial progenitor cells (EPCs) and rapid cell colonization after seeding EPC spheroids. We confirmed that the 3D, but not two-dimensional, scaffold structures regulated tubular structure formation by the EPCs. Thus, incorporation of stem cells into a highly porous 3D scaffold with tunable thickness has implications for the regeneration of vascularized thick tissues and cardiac patch development.

PLGA/gelatin hybrid nanofibrous scaffolds encapsulating EGF for skin regeneration

The novel strategies of skin regenerative treatment are aimed at the development of biologically responsive scaffolds capable of delivering multiple bioactive agents and cells to the target tissues. In this study, nanofibers of poly(lactic-co-glycolic acid) (PLGA) and gelatin were electrospun and the effect of parameters viz polymer concentration, acid concentration, flow rate and voltage on the morphology of the fibers were investigated. PLGA nanofibers encapsulating epidermal growth factor were also prepared through emulsion electrospinning. The core-sheath structure of the nanofibers was verified by transmission electron microscopy. The hemostatic attributes and the biocompatibility of the scaffolds for human fibroblast cell were scrutinized. Furthermore, gene expression of collagen type I and type III by the cells on the scaffolds was quantified using real-time reverse transcriptase polymerase chain reaction. The results indicated desirable bioactivity and hemostasis of the scaffolds with the capability of encapsulation and controlled release of the protein which can be served as skin tissue engineering scaffolds and wound dressings.

Three-dimensional pore structure analysis of polycaprolactone nano-microfibrous scaffolds using theoretical and experimental approaches

In this article the pore structure and porosity parameters of polycaprolactone (PCL) nano-microfibrous scaffolds are investigated using a predicting theoretical model and a nondestructive evaluation approach based on confocal laser scanning microscopy (CLSM) and three-dimensional image analysis. Different fibrous scaffolds with different fiber diameters produced by electrospinning process and their 3D-pore structure were evaluated theoretically and also compared to results of CLSM and capillary flow porometery methods. The effect of polymer concentration on the pore structure of scaffolds was also investigated. The results showed that, the introduced approach not only can measure the pore size distribution of nanofibrous scaffolds, but also can measure pore interconnectivity of fibrous scaffolds. Furthermore, the results showed that increasing the fiber diameter resulted from increasing the polymer concentration in solvent can effectively increase the pore dimensions within the scaffold structure.