Spray Flame Synthesis and Multiscale Characterization of Carbon Black-Silica Hetero-Aggregates

The increasing demand for lithium-ion batteries requires constant improvements in the areas of production and recycling to reduce their environmental impact. In this context, this work presents a method for structuring carbon black aggregates by adding colloidal silica via a spray flame with the goal of opening up more choices for polymeric binders. The main focus of this research lies in the multiscale characterization of the aggregate properties via small-angle X-ray scattering, analytical disc centrifugation and electron microscopy. The results show successful formation of sinter-bridges between silica and carbon black leading to an increase in hydrodynamic aggregate diameter from 201 nm to up to 357 nm, with no significant changes in primary particle properties. However, segregation and coalescence of silica particles was identified for higher mass ratios of silica to carbon black, resulting in a reduction in the homogeneity of the hetero-aggregates. This effect was particularly evident for silica particles with larger diameters of 60 nm. Consequently, optimal conditions for hetero-aggregation were identified at mass ratios below 1 and particle sizes around 10 nm, at which homogenous distributions of silica within the carbon black structure were achieved. The results emphasise the general applicability of hetero-aggregation via spray flames with possible applications as battery materials.

Glassy Carbon Electrode Modified with CB/TiO2 Layer for Sensitive Determination of Sumatriptan by Means of Voltammetry and Flow Injection Analysis

Sumatriptan is an organic chemical compound from the tryptamine group. It is used as a medicine for migraine attacks and in the treatment of cluster headaches. In this work, a new voltammetric method is proposed for highly sensitive SUM determination, using glassy carbon electrodes modified with carbon black and titanium dioxide suspension. The novelty of the presented work is the usage of the mixture of carbon black and TiO₂ as glassy carbon electrode modifier for the first time for SUM determination. The mentioned sensor was characterized by great repeatability and sensitivity of measurements, which resulted in the obtention of a wide range of linearity and a low detection limit. The electrochemical properties of the CB-TiO₂/GC sensor was characterized using the LSV and EIS method. The effect of different factors on the SUM peak, such as supporting electrolyte type, preconcentration time and potential, or influence of interferents, were tested using the square wave voltammetry technique. The linear voltammetric response for the analyte was obtained in the concentration range of 5 nmol L^-1 to 150 μmol L^-1 with a detection limit of 2.9 nmol L^-1 for a preconcentration time of 150 s in the 0.1 mol L^-1 phosphate buffer pH 6.0. The proposed method was successfully applied for highly sensitive sumatriptan determination in complex matrices, such as tablets, urine, and plasma, with a good recovery parameter (94-105%). The presented CB-TiO₂/GC electrode is characterized by great stability, it was used for 6 weeks without significant changes in the SUM peak current. Amperometric and voltammetric measurements of SUM under the flow injection conditions were also performed to indicate the possibility of its fast and accurate determination with a time of single analysis of approx. 30 s.

All-Solid-State Carbon Black Paste Electrodes Modified by Poly(3-octylthiophene-2,5-diyl) and Transition Metal Oxides for Determination of Nitrate Ions

This paper presents new paste ion-selective electrodes for the determination of nitrate ions in soil. The pastes used in the construction of the electrodes are based on carbon black doped with transition metal oxides: ruthenium, iridium, and polymer-poly(3-octylthiophene-2,5-diyl). The proposed pastes were electrically characterized by chronopotentiometry and broadly characterized potentiometrically. The tests showed that the metal admixtures used increased the electric capacitance of the pastes to 470 μF for the ruthenium-doped paste. The polymer additive used positively affects the stability of the electrode response. All tested electrodes were characterized by a sensitivity close to that of the Nernst equation. In addition, the proposed electrodes have a measurement range of 10^-5 to 10^-1 M NO₃^- ions. They are impervious to light conditions and pH changes in the range of 2-10. The utility of the electrodes presented in this work was demonstrated during measurements directly in soil samples. The electrodes presented in this paper show satisfactory metrological parameters and can be successfully used for determinations in real samples.

Natural Rubber Composites Using Hydrothermally Carbonized Hardwood Waste Biomass as a Partial Reinforcing Filler-Part II: Mechanical, Thermal and Ageing (Chemical) Properties

Natural rubber composites were reinforced by the co-fillers 'hydrochar' (HC), obtained by hydrothermal carbonization of hardwood sawdust and commercial carbon black (CB). The content of the combined fillers was kept constant while their ratio was varied. The aim was to test the suitability of HC as a partial filler in natural rubber. Due to its larger particle size and hence smaller specific surface area, large amounts of HC reduced the crosslinking density in the composites. On the other hand, due to its unsaturated organic character, HC was found to display interesting chemical effects: if it was used as the exclusive filler component, it displayed a very strong anti-oxidizing effect, which greatly stabilized the rubber composite against oxidative crosslinking (and hence embrittlement). HC also affected the vulcanization kinetics in different ways, depending on the HC/CB ratio. Composites with HC/CB ratios 20/30 and 10/40 displayed interesting chemical stabilization in combination with fairly good mechanical properties. The performed analyses included vulcanization kinetics, tensile properties, determination of density of permanent and reversible crosslinking in dry and swollen states, chemical stability tests including TGA, thermo-oxidative aging tests in air at 180 °C, simulated weathering in real use conditions ('Florida test'), and thermo-mechanical analyses of degraded samples. Generally, the results indicate that HC could be a promising filler material due to its specific reactivity.

Poly(styrene sulfonic acid)-Grafted Carbon Black Synthesized by Surface-Initiated Atom Transfer Radical Polymerization

Owing to their excellent electrical conductivity and robust mechanical properties, carbon-based nanocomposites are being used in a wide range of applications and devices, such as electromagnetic wave interference shielding, electronic devices, and fuel cells. While several approaches have been developed for synthesizing carbon nanotubes and carbon-black-based polymer nanocomposites, most studies have focused on the simple blending of the carbon material with a polymer matrix. However, this results in uncontrolled interactions between the carbon filler and the polymer chains, leading to the agglomeration of the carbon filler. Herein, we report a new strategy for synthesizing sulfonated polystyrene (PSS)-grafted carbon black nanoparticles (NPs) via surface-initiated atom-transfer radical polymerization. Treatments with O₂ plasma and H₂O₂ result in the effective attachment of the appropriate initiator to the carbon black NPs, thus allowing for the controlled formation of the PSS brushes. The high polymeric processability and desirable mechanical properties of the PSS-grafted carbon black NPs enable them suitable for use in nonfluorinated-hydrocarbon-based polymer electrolyte membranes for fuel cells, which must exhibit high proton conductivity without interrupting the network of channels consisting of ionic clusters (i.e., sulfonic acid moieties).

Investigating the Electromechanical Properties of Carbon Black-Based Conductive Polymer Composites via Stochastic Modeling

Conductive polymer composites (CPCs) have shown potential for structural health monitoring applications based on repeated findings of irreversible transducer electromechanical property change due to fatigue. In this research, a high-fidelity stochastic modeling framework is explored for predicting the electromechanical properties of spherical element-based CPC materials at bulk scales. CPC dogbone specimens are manufactured via casting and their electromechanical properties are characterized via uniaxial tensile testing. Model parameter tuning, demonstrated in previous works, is deployed for improved simulation fidelity. Modeled predictions are found in agreement with experimental results and compared to predictions from a popular analytical model in the literature.

Ex Situ Study on the Co-Preparation of Pitch and Carbon Black from Petroleum Residue to Improve the Cost-Efficiency of the Pitch Synthesis Plant

This study aims to improve the economic efficiency of the pitch synthesis reaction on the pilot plant by optimizing the pitch synthesis reaction and utilization of the byproduct. The pitch was synthesized using a 150 L pilot plant with pyrolyzed fuel oil as a precursor. The pitch synthesis reaction is carried out through volatilization and polycondensation, which occur at 300 and 400 °C. Volatilization is terminated during heating; thus, additional soaking time is meaningless and reduces the process efficiency. Soaking time is a major variable when the synthesis temperature exceeds 400 °C. The byproduct is generated through volatilization; thus, its chemical characteristics are only influenced by the reaction temperature. The byproduct consists of various polycyclic aromatic hydrocarbons. The average molecular weight and yield of the byproduct increase with the reaction temperature. Carbon black was synthesized using chemical vapor deposition from the byproduct. The particle size of carbon black was controlled by the used precursor (byproduct), and the electrical conductivity of prepared carbon black has a maximum of 58.0 S/cm. Therefore, carbon black, which is synthesized from the byproduct of pitch synthesis, is expected to be used as a precursor for conductive material used in lithium-ion batteries or supercapacitors.

Significant Influence of Bound Rubber Thickness on the Rubber Reinforcement Effect

In this work, the contribution of different types of carbon blacks (N115, N330, N550, N660) and their primary and secondary thermally cracked recovered carbon blacks to the mechanical properties of NR composites was evaluated. The thermally cracked recovered carbon blacks were prepared by cracking the rubber composites at 500 °C and de-hybridizing them at 900 °C. The characterization of the thermally cracked recovered carbon blacks by scanning electron microscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy showed that carbon blacks after primary and secondary thermal cracking recovery were more prone to aggregation and exhibited a higher degree of carbon defects. The number and type of functional groups on the surface of these carbon blacks were significantly reduced. For NR composites with pristine samples added, the mechanical properties and the bound rubber content tests showed that the mechanical properties of the NR composites became weaker with the increase in carbon black particle size. The bound rubber content also decreased with increased carbon black particle size. The mechanical properties of the NR composites reinforced with carbon black recovered by primary and secondary thermal cracking would therefore decrease. The results of AFM and DSC tests further confirmed the decreasing trend of bound rubber. The present work demonstrates the effect of bound rubber content variation on the mechanical properties of rubber, demonstrates the morphology of bound rubber more visually, and provides new insights into the reinforcement theory of CB.

Evaluation of Piezoresistive and Electrical Properties of Conductive Nanocomposite Based on Castor-Oil Polyurethane Filled with MWCNT and Carbon Black

Flexible films of a conductive polymer nanocomposite-based castor oil polyurethane (PUR), filled with different concentrations of carbon black (CB) nanoparticles or multiwall carbon nanotubes (MWCNTs), were obtained by a casting method. The piezoresistive, electrical, and dielectric properties of the PUR/MWCNT and PUR/CB composites were compared. The dc electrical conductivity of both PUR/MWCNT and PUR/CB nanocomposites exhibited strong dependences on the concentration of conducting nanofillers. Their percolation thresholds were 1.56 and 1.5 mass%, respectively. Above the threshold percolation level, the electrical conductivity value increased from 1.65 × 10^-12 for the matrix PUR to 2.3 × 10^-3 and 1.24 × 10^-5 S/m for PUR/MWCNT and PUR/CB samples, respectively. Due to the better CB dispersion in the PUR matrix, the PUR/CB nanocomposite exhibited a lower percolation threshold value, corroborated by scanning electron microscopy images. The real part of the alternating conductivity of the nanocomposites was in accordance with Jonscher's law, indicating that conduction occurred by hopping between states in the conducting nanofillers. The piezoresistive properties were investigated under tensile cycles. The nanocomposites exhibited piezoresistive responses and, thus, could be used as piezoresistive sensors.

Evolution of the Viscoelastic Properties of Filler Reinforced Rubber under Physical Aging at Room Temperature

Filler reinforced rubber is widely used for engineering applications; therefore, a sound characterization of the effects of physical aging is crucial for accurately predicting its viscoelastic properties within its operational temperature range. Here, the torsion pendulum is used to monitor the evolution of the storage and loss modulus of carbon black filled samples for four days after a temperature drop to 30 °C. The storage modulus presents a continuous increase, while the loss modulus generally displays a steady decrease throughout the four days that each test was conducted. The relationship of the recovery rates with the carbon black properties is also studied, analysing its dependency on the particle size and aggregate structure. The evolution of the recovery rate seems to depend linearly on the surface area while the carbon black structure appears to have a much weaker influence on the physical aging behavior for the set of compounds tested. The obtained results corroborate the presence of physical aging at room temperature for filler rubber materials and the ability of the torsion pendulum to monitor the storage and loss modulus change, providing pivotal data on the influence of physical aging on the viscoelastic properties of the material.

Atomically Dispersed Fe-N4 Sites and NiFe-LDH Sub-Nanoclusters as an Excellent Air Cathode for Rechargeable Zinc-Air Batteries

The sluggish four-electron processes of the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) limit the development of rechargeable Zn-air batteries (RZABs). Highly efficient ORR/OER bifunctional electrocatalysts are therefore highly desired for the commercialization of RZABs in large scale. Herein, the Fe-N₄-C (ORR active sites) and NiFe-LDH clusters (OER active sites) are successfully integrated within a NiFe-LDH/Fe,N-CB electrocatalyst. The NiFe-LDH/Fe,N-CB electrocatalyst is first prepared by the introduction of Fe-N₄ into carbon black (CB), followed by the growth of NiFe-LDH clusters. The cluster nature of NiFe-LDH effectively avoids the blocking of Fe-N₄-C ORR active centers and affords excellent OER activity. The NiFe-LDH/Fe,N-CB electrocatalyst thus exhibits an excellent bifunctional ORR and OER performance, with a potential gap of only 0.71 V. The NiFe-LDH/Fe,N-CB-based RZAB exhibits an open-circuit voltage of 1.565 V and a specific capacity of 731 mAh g_Zn^-1, which is much better than the RZAB composed of Pt/C and IrO₂. Particularly, the NiFe-LDH/Fe,N-CB-based RZAB displays excellent long-term charging/discharging cyclic stability and rechargeability. Even at a large charging/discharging current density (20 mA cm^-2), the charging/discharging voltage gap is only ∼1.33 V and exhibits an increase smaller than 5% after 140 cycles. This work provides a new low-cost bifunctional ORR/OER electrocatalyst with high activity and superior long-term stability and will be helpful to the commercialization of RZAB in large scale.

Carbon Nanomaterials-Based Screen-Printed Electrodes for Sensing Applications

Electrochemical sensors consisting of screen-printed electrodes (SPEs) are recurrent devices in the recent literature for applications in different fields of interest and contribute to the expanding electroanalytical chemistry field. This is due to inherent characteristics that can be better (or only) achieved with the use of SPEs, including miniaturization, cost reduction, lower sample consumption, compatibility with portable equipment, and disposability. SPEs are also quite versatile; they can be manufactured using different formulations of conductive inks and substrates, and are of varied designs. Naturally, the analytical performance of SPEs is directly affected by the quality of the material used for printing and modifying the electrodes. In this sense, the most varied carbon nanomaterials have been explored for the preparation and modification of SPEs, providing devices with an enhanced electrochemical response and greater sensitivity, in addition to functionalized surfaces that can immobilize biological agents for the manufacture of biosensors. Considering the relevance and timeliness of the topic, this review aimed to provide an overview of the current scenario of the use of carbonaceous nanomaterials in the context of making electrochemical SPE sensors, from which different approaches will be presented, exploring materials traditionally investigated in electrochemistry, such as graphene, carbon nanotubes, carbon black, and those more recently investigated for this (carbon quantum dots, graphitic carbon nitride, and biochar). Perspectives on the use and expansion of these devices are also considered.

Ianăşi) P, Popa A, Lazău R, Negrea A, Negrea P, Duteanu N, Ciopec M, Nemes NS. Adsorbent Material Based on Carbon Black and Bismuth with Tunable Properties for Gold Recovery

Adsorption recovery of precious metals on a variety of solid substrates has steadily gained increased attention in recent years. Special attention was paid to the studies on the characterization of the adsorptive properties of materials with a high affinity for gold depending on the nature of the pendant groups present in the structure of the material. The aim of the present work was to synthesize and characterize a new material by using the sol-gel synthesis method (designated as BCb/CB). In this case, synthesis involved the following precursors: bismuth carbonate (III), carbon black, and IGEPAL surfactant (octylphenoxypolyethoxyethanol). Immobilization of the heterojunction as bismuth oxide over a flexible support such as carbon black (CB) can prevent their elution in solution and make it versatile for its use in a system. In this work, a new adsorbent material based on bismuth carbonate supported over carbon black (BCb/CB) was developed and used further for gold recovery from aqueous solutions. The required material was characterized physically/chemically by scanning electron microscopy (SEM); energy dispersive X-ray spectrometry (EDX); X-ray diffraction (XRD); thermal analysis (DTG/DTA); atomic force microscopy (AFM). The Brunauer-Emmett-Teller (BET) method was used to determine the specific surface area indicating a value of approximately 40 m²/g, higher than the surface of CB precursor (36 m²/g). The adsorptive properties and the adsorption mechanism of the materials were highlighted in order to recover Au(III). For this, static adsorption studies were carried out. The parameters that influence the adsorption process were studied, namely: the pH, the contact time, the temperature, and the initial concentration of the gold ions in the used solution. In order to establish the mechanism of the adsorption process, kinetic, thermodynamic, and equilibrium studies were carried out. Experimental data proved that the gold recovery can be conducted with maximum performance at pH 3, at room temperature. Thermodynamic studies proved that the gold adsorption on BCb/CB material is a spontaneous and endothermal process. The results indicate a total adsorption capacity of 13.1 mg Au(III)/g material. By using this material in real solutions, a recovery efficiency of 90.5% was obtained, concomitant with a higher selectivity (around 95%).

Theoretical and experimental approach of fuel gas and carbon black production from coal tar pitch by thermal plasma process

The processing of coal tar pitch (CTP) to produce clean fuel gas and carbon black (CB) is studied in a plasma reactor equipped with a direct-current plasma torch. The composition of the gas produced and energy costs were estimated theoretically for the CTP pyrolysis and gasification processes by two oxidants, namely oxygen and water vapor. We have found that the main gaseous compounds obtained in the pyrolysis and gasification processes are hydrogen (H₂), carbon monoxide (CO), and very often carbon dioxide (CO₂). For the pyrolysis case, the mean value of the synthesis gas concentration reaches a major value of 98 vol.% (H₂ - 81 vol.%, CO - 17. vol.%). However, only 23% of the initial CTP is transformed into gas phase at 1100 K and its content increases up to 37.4% at a temperature of 3000 K. For oxygen gasification, the syngas quantity is little less compared to the pyrolysis case and attains 96.6 vol.% (H₂ - 26.5 vol.%, CO - 70.1 vol.%) for T > 1100 K. An intermediate syngas content for the water steam gasification is 97.8 vol.% (with H₂ - 55.8 vol.% and CO - 42.0 vol.%). The CB produced was composed of well-defined spherical particles of 30-nm size. Furthermore, it is composed of carbon (98.2%), and followed by oxygen (1.8%) with a surface area of 97 m² g^-1. The thermal plasma system shows high efficiency in conversion of CTP into high-value-added products.

Self-Sensing Rubber for Bridge Bearing Monitoring

Elastomeric bearings are widely used in bridges to support the superstructure, to transfer loads to substructures, and to accommodate movements induced by, for example, temperature changes. Bearing mechanical properties affect the bridge's performance and its response to permanent and variable loadings (e.g., traffic). This paper describes the research carried out at Strathclyde towards the development of smart elastomeric bearings that can be used as a low-cost sensing technology for bridge and/or weigh-in-motion monitoring. An experimental campaign was performed, under laboratory conditions, on various natural rubber (NR) specimens enhanced with different conductive fillers. Each specimen was characterized under loading conditions that replicated in-situ bearings to determine their mechanical and piezoresistive properties. Relatively simple models can be used to describe the relationship between rubber bearing resistivity and deformation changes. Gauge factors (GFs) in the range between 2 and 11 are obtained, depending on the compound and the applied loading. Experiments were also carried out to show that the developed model can be used to predict the state of deformation of the bearings under random loadings of different amplitudes that are characteristic of the passage of traffic over a bridge.

Conformable Electrode Arrays for Wearable Neuroprostheses

Wearable electrode arrays can selectively stimulate muscle groups by modulating their shape, size, and position over a targeted region. They can potentially revolutionize personalized rehabilitation by being noninvasive and allowing easy donning and doffing. Nevertheless, users should feel comfortable using such arrays, as they are typically worn for an extended time period. Additionally, to deliver safe and selective stimulation, these arrays must be tailored to a user's physiology. Fabricating customizable electrode arrays needs a rapid and economical technique that accommodates scalability. By leveraging a multilayer screen-printing technique, this study aims to develop personalizable electrode arrays by embedding conductive materials into silicone-based elastomers. Accordingly, the conductivity of a silicone-based elastomer was altered by adding carbonaceous material. The 1:8 and 1:9 weight ratio percentages of carbon black (CB) to elastomer achieved conductivities between 0.0021-0.0030 S cm^-1 and were suitable for transcutaneous stimulation. Moreover, these ratios maintained their stimulation performance after several stretching cycles of up to 200%. Thus, a soft, conformable electrode array with a customizable design was demonstrated. Lastly, the efficacy of the proposed electrode arrays to stimulate hand function tasks was evaluated by in vivo experiments. The demonstration of such arrays encourages the realization of cost-effective, wearable stimulation systems for hand function restoration.

Characterization of Carbon-Black-Based Nanocomposite Mixtures of Varying Dispersion for Improving Stochastic Model Fidelity

Carbon black nanocomposites are complex systems that show potential for engineering applications. Understanding the influence of preparation methods on the engineering properties of these materials is critical for widespread deployment. In this study, the fidelity of a stochastic fractal aggregate placement algorithm is explored. A high-speed spin-coater is deployed for the creation of nanocomposite thin films of varying dispersion characteristics, which are imaged via light microscopy. Statistical analysis is performed and compared to 2D image statistics of stochastically generated RVEs with comparable volumetric properties. Correlations between simulation variables and image statistics are examined. Future and current works are discussed.

Natural Rubber Composites Using Hydrothermally Carbonized Hardwood Waste Biomass as a Partial Reinforcing Filler- Part I: Structure, Morphology, and Rheological Effects during Vulcanization

A new generation biomass-based filler for natural rubber, 'hydrochar' (HC), was obtained by hydrothermal carbonization of hardwood waste (sawdust). It was intended as a potential partial replacement for the traditional carbon black (CB) filler. The HC particles were found (TEM) to be much larger (and less regular) than CB: 0.5-3 µm vs. 30-60 nm, but the specific surface areas were relatively close to each other (HC: 21.4 m²/g vs. CB: 77.8 m²/g), indicating a considerable porosity of HC. The carbon content of HC was 71%, up from 46% in sawdust feed. FTIR and ¹³C-NMR analyses indicated that HC preserved its organic character, but it strongly differs from both lignin and cellulose. Experimental rubber nanocomposites were prepared, in which the content of the combined fillers was set at 50 phr (31 wt.%), while the HC/CB ratios were varied between 40/10 and 0/50. Morphology investigations proved a fairly even distribution of HC and CB, as well as the disappearance of bubbles after vulcanization. Vulcanization rheology tests demonstrated that the HC filler does not hinder the process, but it significantly influences vulcanization chemistry, canceling scorch time on one hand and slowing down the reaction on the other. Generally, the results suggest that rubber composites in which 10-20 phr of CB are replaced by HC might be promising materials. The use of HC in the rubber industry would represent a high-tonnage application for hardwood waste.

Performance Optimization of Wearable Printed Human Body Temperature Sensor Based on Silver Interdigitated Electrode and Carbon-Sensing Film

The human body's temperature is one of the most important vital markers due to its ability to detect various diseases early. Accurate measurement of this parameter has received considerable interest in the healthcare sector. We present a novel study on the optimization of a temperature sensor based on silver interdigitated electrodes (IDEs) and carbon-sensing film. The sensor was developed on a flexible Kapton thin film first by inkjet printing the silver IDEs, followed by screen printing a sensing film made of carbon black. The IDE finger spacing and width of the carbon film were both optimized, which considerably improved the sensor's sensitivity throughout a wide temperature range that fully covers the temperature of human skin. The optimized sensor demonstrated an acceptable temperature coefficient of resistance (TCR) of 3.93 × 10^-3 °C^-1 for temperature sensing between 25 °C and 50 °C. The proposed sensor was tested on the human body to measure the temperature of various body parts, such as the forehead, neck, and palm. The sensor showed a consistent and reproducible temperature reading with a quick response and recovery time, exhibiting adequate capability to sense skin temperatures. This wearable sensor has the potential to be employed in a variety of applications, such as soft robotics, epidermal electronics, and soft human-machine interfaces.

Correlations between H2 Permeation and Physical/Mechanical Properties in Ethylene Propylene Diene Monomer Polymers Blended with Carbon Black and Silica Fillers

H₂ permeation in peroxide-crosslinked EPDM blended with carbon black (CB) and silica fillers was studied at pressures ranging from 1.2 MPa to 90 MPa via the volumetric analysis technique. H₂ uptake in the CB-filled EPDM revealed dual-sorption behaviors via Henry's law and the Langmuir model, which were attributed to H₂ absorption by the polymer chains and H₂ adsorption at the filler interfaces, respectively. Additionally, single-sorption mechanisms were observed for neat EPDM and silica-blended EPDM according to Henry's law, indicating H₂ absorption by the polymer chain. The linear decreases in the diffusivity with filler content for the silica-blended EPDMs were attributed to increases in the diffusion paths caused by the filler. Exponential decreases in the diffusivity with increasing filler content and in the permeation with the physical/mechanical properties for CB-filled EPDMs were caused by decreases in the fractional free volume due to increased densities for the EPDM composites. Moreover, good filler-dependent correlations between permeability and density, hardness, and tensile strength were demonstrated for EPDMs used as sealing materials for O-rings. From the resulting equation, we predicted the permeation value without further measurements. Thus, we can select EPDM candidates satisfying the permeation guidelines used in hydrogen infrastructure for the future hydrogen economy.

Investigation of Amorphous Carbon in Nanostructured Carbon Materials (A Comparative Study by TEM, XPS, Raman Spectroscopy and XRD)

Amorphous carbon (AC) is present in the bulk and on the surface of nanostructured carbon materials (NCMs) and exerts a significant effect on the physical, chemical and mechanical properties of NCMs. Thus, the determination of AC in NCMs is extremely important for controlling the properties of a wide range of materials. In this work, a comparative study of the effect of heat treatment on the structure and content of amorphous carbon in deposited AC film, nanodiamonds, carbon black and multiwalled carbon nanotube samples was carried out by TEM, XPS, XRD and Raman spectroscopy. It has been established that the use of the 7-peak model for fitting the Raman spectra makes it possible not only to isolate the contribution of the modes of amorphous carbon but also to improve the accuracy of fitting the fundamental G and D₂ (D) modes and obtain a satisfactory convergence between XPS and Raman spectroscopy. The use of this model for fitting the Raman spectra of deposited AC film, ND, CB and MWCNT films demonstrated its validity and effectiveness for investigating the amorphous carbon in various carbon systems and its applicability in comparative studies of other NCMs.

A Sensitive Hydroquinone Amperometric Sensor Based on a Novel Palladium Nanoparticle/Porous Silicon/Polypyrrole-Carbon Black Nanocomposite

Exposure to hydroquinone (HQ) can cause various health hazards and negative impacts on the environment. Therefore, we developed an efficient electrochemical sensor to detect and quantify HQ based on palladium nanoparticles deposited in a porous silicon-polypyrrole-carbon black nanocomposite (Pd@PSi-PPy-C)-fabricated glassy carbon electrode. The structural and morphological characteristics of the newly fabricated Pd@PSi-PPy-C nanocomposite were investigated utilizing FESEM, TEM, EDS, XPS, XRD, and FTIR spectroscopy. The exceptionally higher sensitivity of 3.0156 μAμM^-1 cm^-2 and a low limit of detection (LOD) of 0.074 μM were achieved for this innovative electrochemical HQ sensor. Applying this novel modified electrode, we could detect wide-ranging HQ (1-450 μM) in neutral pH media. This newly fabricated HQ sensor showed satisfactory outcomes during the real sample investigations. During the analytical investigation, the Pd@PSi-PPy-C/GCE sensor demonstrated excellent reproducibility, repeatability, and stability. Hence, this work can be an effective method in developing a sensitive electrochemical sensor to detect harmful phenol derivatives for the green environment.

Fabrication of ZnWO4/Carbon Black Nanocomposites Modified Glassy Carbon Electrode for Enhanced Electrochemical Determination of Ciprofloxacin in Environmental Water Samples

The major problem facing humanity in the world right now is the sustainable provision of water and electricity. Therefore, it is essential to advance methods for the long-term elimination or removal of organic contaminants in the biosphere. Ciprofloxacin (CIP) is one of the most harmful pollutants affecting human health through improper industrial usage. In this study, a zinc tungsten oxide (ZnWO₄) nanomaterial was prepared with a simple hydrothermal synthesis. The ZnWO₄/Carbon black nanocomposites were fabricated for the determination of CIP. The nanocomposites were characterized by field emission scanning electron microscopy, energy dispersion X-ray spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and electrochemical impedance spectroscopy. Electrochemical studies were done using cyclic voltammetry and differential pulse voltammetry methods. Based on the electrode preparation, the electrochemical detection of CIP was carried out, producing exceptional electrocatalytic performance with a limit of detection of 0.02 μM and an excellent sensitivity of (1.71 μA μM^-1 cm^-2). In addition, the modified electrode displayed great selectivity and acceptable recoveries in an environmental water sample analysis for CIP detection of 97.6% to 99.2%. The technique demonstrated high sensitivity, selectivity, outstanding consistency, and promise for use in ciprofloxacin detection. Ciprofloxacin was discovered using this brand-new voltammetry technique in a water sample analysis.

Effects of Electrode Materials and Compositions on the Resistance Behavior of Dielectric Elastomer Transducers

Dielectric elastomer (DE) transducers possess various advantages in comparison to alternative actuator technologies, such as, e.g., electromagnetic drive systems. DE can achieve large deformations, high driving frequencies, and are energy efficient. DEs consist of a dielectric membrane sandwiched between conductive electrodes. Electrodes are especially important for performance, as they must maintain high electrical conductivity while being subjected to large stretches. Low electrical resistances allow faster actuation frequencies. Additionally, a rate-independent, monotonic, and hysteresis-free resistance behavior over large elongations enables DEs to be used as resistive deformation sensors, in contrast to the conventional capacitive ones. This paper presents a systematic study on various electrode compositions consisting of different polydimethylsiloxane (PDMS) and nano-scaled carbon blacks (CB). The experiments show that the electrode resistance depends on the weight ratio of CB to PDMS, and the type of CB used. At low ratios, a high electrical resistance accompanied by a bimodal behavior in the resistance time evolution was observed, when stretching the electrodes cyclic in a triangular manner. This phenomenon decreases with increasing CB ratio. The type of PDMS also influences the resistance characteristics during elongation. Finally, a physical model of the observed phenomenon is presented.

H2 Uptake and Diffusion Characteristics in Sulfur-Crosslinked Ethylene Propylene Diene Monomer Polymer Composites with Carbon Black and Silica Fillers after High-Pressure Hydrogen Exposure Reaching 90 MPa

We investigated the influence of two fillers-CB (carbon black) and silica-on the H₂ permeation of EPDM polymers crosslinked with sulfur in the pressure ranges 1.2-90 MPa. H₂ uptake in the CB-blended EPDM revealed dual sorption (Henry's law and Langmuir model) when exposed to pressure. This phenomenon indicates that H₂ uptake is determined by the polymer chain and filler-surface absorption characteristics. Moreover, single sorption characteristics for neat and silica-blended EPDM specimens obey Henry's law, indicating that H₂ uptake is dominated by polymer chain absorption. The pressure-dependent diffusivity for the CB-filled EPDM is explained by Knudsen and bulk diffusion, divided at the critical pressure region. The neat and silica-blended EPDM specimens revealed that bulk diffusion behaviors decrease with decreasing pressure. The H₂ diffusivities in CB-filled EPDM composites decrease because the impermeable filler increases the tortuosity in the polymer and causes filler-polymer interactions; the linear decrease in diffusivity in silica-blended EPDM was attributed to an increase in the tortuosity. Good correlations of permeability with density and tensile strength were observed. From the investigated relationships, it is possible to select EPDM candidates with the lowest H₂-permeation properties as seal materials to prevent gas leakage under high pressure in H₂-refueling stations.