Constructing Built-In Electric Field in NiCo2 O4 -CeO2 Heterostructures to Regulate Li2 O2 Formation Routes at High Current Densities

Developing catalysts with suitable adsorption energy for oxygen-containing intermediates and elucidating their internal structure-performance relationships are essential for the commercialization of Li-O2 batteries (LOBs), especially under high current densities. Herein, NiCo2 O4 -CeO2 heterostructure with a spontaneous built-in electric field (BIEF) is designed and utilized as a cathode catalyst for LOBs at high current density. The driving mechanism of electron pumping/accumulation at heterointerface is studied via experiments and density functional theory (DFT) calculations, elucidating the growth mechanism of discharge products. The results show that BIEF induced by work function difference optimizes the affinity for LiO2 and promotes the formation of nano-flocculent Li2 O2 , thus improving LOBs performance at high current density. Specifically, NiCo2 O4 -CeO2 cathode exhibits a large discharge capacity (9546 mAh g-1 at 4000 mA g-1 ) and high stability (>430 cycles at 4000 mA g-1 ), which are better than the majority of previously reported metal-based catalysts. This work provides a new method for tuning the nucleation and decomposition of Li2 O2 and inspires the design of ideal catalysts for LOBs to operate at high current density.

Valorisation of Sub-Products from Pyrolysis of Carbon Fibre-Reinforced Plastic Waste: Catalytic Recovery of Chemicals from Liquid and Gas Phases

Waste carbon fibre-reinforced plastics were recycled by pyrolysis followed by a thermo-catalytic treatment in order to achieve both fibre and resin recovery. The conventional pyrolysis of this waste produced unusable gas and hazardous liquid streams, which made necessary the treatment of the pyrolysis vapours. In this work, the vapours generated from pyrolysis were valorised thermochemically. The thermal treatment of the pyrolysis vapours was performed at 700 °C, 800 °C and 900 °C, and the catalytic treatment was tested at 700 °C and 800 °C with two Ni-based catalysts, one commercial and one homemade over a non-conventional olivine support. The catalysts were deeply characterised, and both had low surface area (99 m2/g and 4 m2/g, respectively) with low metal dispersion. The thermal treatment of the pyrolysis vapours at 900 °C produced high gas quantity (6.8 wt%) and quality (95.5 vol% syngas) along with lower liquid quantity (13.3 wt%) and low hazardous liquid (92.1 area% water). The Ni-olivine catalyst at the lowest temperature, 700 °C, allowed us to obtain good gas results (100% syngas), but the liquid was not as good (only 58.4 area% was water). On the other hand, the Ni commercial catalyst at 800 °C improved both the gas and liquid phases, producing 6.4 wt% of gas with 93 vol% of syngas and 13.6 wt% of liquid phase with a 97.5 area% of water. The main reaction mechanisms observed in the treatment of pyrolysis vapours were cracking, dry and wet reforming and the Boudouard reaction.

CO2-Driven N-Formylation/N-Methylation of Amines Using C-Scorpionate Metal Complexes

C-scorpionate metal complexes, specifically, [NiCl2(tpm)]·3H2O, [CoCl2(tpm)]·3H2O and [PdCl2(tpm)] [tpm = hydrotris(1H-pyrazol-1-yl)methane], were effective in the N-formylation and N-methylation of amines using carbon dioxide, as carbon source, in the presence of sodium borohydride. Various parameters were studied, including reaction time, temperature, solvent volume, presence of additives, and catalyst amount. These parameters were found to have a significant impact on the selectivity of the product. [NiCl2(tpm)]·3H2O exhibited good conversion at 80 °C, but its selectivity towards formamide decreased with prolonged reaction time. Increasing the amount of [NiCl2(tpm)]·3H2O, the selectivity changed. [PdCl2(tpm)] showed different selectivity compared to [NiCl2(tpm)]·3H2O, while [CoCl2(tpm)]·3H2O presented poor results. Monitoring the reaction course by 1H NMR revealed the presence of an intermediate species that influenced product formation. These results highlight the versatility and catalytic potential of C-scorpionate metal complexes in the N-formylation/N-methylation of amines in the catalytic system (NaBH4/MeCN/CO2).

A High-Performance Cr2O3/CaCO3 Nanocomposite Catalyst for Rapid Hydrogen Generation from NaBH4

This study aims to prepare new nanocomposites consisting of Cr2O3/CaCO3 as a catalyst for improved hydrogen production from NaBH4 methanolysis. The new nanocomposite possesses nanoparticles with the compositional formula Cr2-xCaxO3 (x = 0, 0.3, and 0.6). These samples were prepared using the sol-gel method, which comprises gelatin fuel. The structure of the new composites was studied using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, environmental scanning electron microscopy (ESEM), and X-ray spectroscopy (XPS). The XRD data showed the rhombohedral crystallinity of the studied samples, and the average crystal size was 25 nm. The FTIR measurements represented the absorption bands of Cr2O3 and CaO. The ESEM micrographs of the Cr2O3 showed the spherical shape of the Cr2O3 nanoparticles. The XPS measurements proved the desired oxidation states of the Cr2-xCaxO3 nanoparticles. The optical band gap of Cr2O3 is 3.0 eV, and calcium doping causes a reduction to 2.5 and 1.3 eV at 15.0 and 30.0% doping ratios. The methanolysis of NaBH4 involved accelerated H2 production when using Cr2-xCaxO3 as a catalyst. Furthermore, the Cr1.7Ca0.3O3 catalyst had the highest hydrogen generation rate, with a value of 12,750 mL/g/min.

Dihydroazolopyrimidines: Past, Present and Perspectives in Synthesis, Green Chemistry and Drug Discovery

Dihydroazolopyrimidines are an important class of heterocycles that are isosteric to natural purines and are therefore of great interest primarily as drug-like molecules. In contrast to the heteroaromatic analogs, synthetic approaches to these compounds were developed much later, and their chemical properties and biological activity have not been studied in detail until recently. In the review, different ways to build dihydroazolopyrimidine systems from different building blocks are described - via the initial formation of a partially hydrogenated pyrimidine ring or an azole ring, as well as a one-pot assembly of azole and azine fragments. Special attention is given to modern approaches: multicomponent reactions, green chemistry, and the use of non-classical activation methods. Information on the chemical properties of dihydroazolopyrimidines and the prospects for their use in the design of drugs of various profiles are also summarized in this review.

Harnessing fungal bio-electricity: a promising path to a cleaner environment

Integrating fungi into fuel cell systems presents a promising opportunity to address environmental pollution while simultaneously generating energy. This review explores the innovative concept of constructing wetlands as fuel cells for pollutant degradation, offering a practical and eco-friendly solution to pollution challenges. Fungi possess unique capabilities in producing power, fuel, and electricity through metabolic processes, drawing significant interest for applications in remediation and degradation. Limited data exist on fungi's ability to generate electricity during catalytic reactions involving various enzymes, especially while remediating pollutants. Certain species, such as Trametes versicolor, Ganoderma lucidum, Galactomyces reessii, Aspergillus spp., Kluyveromyce smarxianus, and Hansenula anomala, have been reported to generate electricity at 1200 mW/m3, 207 mW/m2, 1,163 mW/m3, 438 mW/m3, 850,000 mW/m3, and 2,900 mW/m3, respectively. Despite the eco-friendly potential compared to conventional methods, fungi's role remains largely unexplored. This review delves into fungi's exceptional potential as fuel cell catalysts, serving as anodic or cathodic agents to mitigate land, air, and water pollutants while simultaneously producing fuel and power. Applications cover a wide range of tasks, and the innovative concept of wetlands designed as fuel cells for pollutant degradation is discussed. Cost-effectiveness may vary depending on specific contexts and applications. Fungal fuel cells (FFCs) offer a versatile and innovative solution to global challenges, addressing the increasing demand for alternative bioenergy production amid population growth and expanding industrial activities. The mechanistic approach of fungal enzymes via microbial combinations and electrochemical fungal systems facilitates the oxidation of organic substrates, oxygen reduction, and ion exchange membrane orchestration of essential reactions. Fungal laccase plays a crucial role in pollutant removal and monitoring environmental contaminants. Fungal consortiums show remarkable potential in fine-tuning FFC performance, impacting both power generation and pollutant degradation. Beyond energy generation, fungal cells effectively remove pollutants. Overall, FFCs present a promising avenue to address energy needs and mitigate pollutants simultaneously.

Low-temperature methanation of fermentation gas with Ni-based catalysts in a multicomponent system

A large amount of greenhouse gases, such as carbon dioxide and methane, are released during the production process of bioethanol and biogas. Converting CO2 into methane is a promising way of capturing CO2 and generating high-value gas. At present, CO2 methanation technology is still in the early stage. It requires high temperature (300-400 ℃) and pressure (> 1 MPa), leading to high cost and energy consumption. In this study, a new catalyst, Ni-Fe/Al-Ti, was developed. Compared with the activity of the common Ni/Al2O3 catalyst, that of the new catalyst was increased by 1/3, and its activation temperature was reduced by 100℃. The selectivity of methane was increased to 99%. In the experiment using simulated fermentation gas, the catalyst showed good catalytic activity and durability at a low temperature and atmospheric pressure. Based on the characterization of catalysts and the study of reaction mechanisms, this article innovatively proposed a Ni-Fe/Al-Ti quaternary catalytic system. Catalytic process was realized through the synergism of Al-Ti composite support and Ni-Fe promotion. The oxygen vacancies on the surface of the composite carrier and the higher activity metals and alloys promoted by Fe accelerate the capture and reduction of CO2. Compared with the existing catalysts, the new Ni-Fe/Al-Ti catalyst can significantly improve the methanation efficiency and has great practical application potential.

Anchoring of Copper(II)-Schiff Base Complex in SBA-15 Matrix as Efficient Oxidation and Biomimetic Catalyst

A new mononuclear Cu(II) complex [Cu(L2)(H2O)2], where L is the Schiff base 2-[2-(3-bromopropoxy)benzylideneamino] benzoic acid, was synthesized and covalently anchored onto an amino-functionalized SBA-15 mesoporous silica in order to obtain an efficient heterogeneous catalyst. The elemental, structural, textural and morphological characterization confirmed the coordination of the central Cu(II) ion with two ligands and two H2O molecules in the synthesized complex and its successful immobilization into the inner pore surface of the NH2-functionalized support without the loss of the mesoporous structure. The catalytic activity of the free or immobilized Cu(II) complex was tested in the oxidation of cyclohexene with H2O2 under an air atmosphere and the dismutation reaction of the superoxide radical anions with very good results. In addition, catalyst reuse tests claim its suitability in alkene oxidation processes or as a biomimetic catalyst.

MatGD: Materials Graph Digitizer

We developed Material Graph Digitizer (MatGD), which is a tool for digitizing a data line from scientific graphs. The algorithm behind the tool consists of four steps: (1) identifying graphs within subfigures, (2) separating axes and data sections, (3) discerning the data lines by eliminating irrelevant graph objects and matching with the legend, and (4) data extraction and saving. From the 62,534 papers in the areas of batteries, catalysis, and metal-organic frameworks (MOFs), 501,045 figures were mined. Remarkably, our tool showcased performance with over 99% accuracy in legend marker and text detection. Moreover, its capability for data line separation stood at 66%, which is much higher compared to those of other existing figure-mining tools. We believe that this tool will be integral to collecting both past and future data from publications, and these data can be used to train various machine learning models that can enhance material predictions and new materials discovery.

Coordination-Polymer-Derived Cu-CoO/C Nanocomposite Used in Fenton-like Reaction to Achieve Efficient Degradation of Organic Compounds

In this paper, carbon-matrix-supported copper (Cu) and cobaltous oxide (CoO) nanoparticles were obtained by using coordination polymers (CPs) as a precursor. The aqueous solutions of copper methacrylate (CuMA) and cobalt methacrylate (CoMA) were preferentially prepared, which were then mixed with anhydrous ethanol to fabricate dual metal ion coordination polymers (CuMA/CoMA). After calcination under an argon atmosphere, the Cu-CoO/C nanocomposite was obtained. Scanning electron microscope (SEM) and transmission electron microscope (TEM) showed that the material has banded morphology, and the dual functional nanoparticles were highly dispersed in the carbon matrix. The prepared material was used in a heterogeneous Fenton-like reaction, with the aim of replacing traditional ferric catalysts to solve pH constraints and the mass production of ferric slime. The obtained nanocomposite showed excellent catalytic performance on the degradation of methylene blue (MB) at near-neutral conditions; the discoloration efficiency is about 98.5% within 50 min in the presence of 0.15 mmol/mL H2O2 and 0.5 mg/mL catalyst. And good reusability was verified via eight cycles. The plausible pathway for MB discoloration and the possible catalytic mechanism was also proposed.

An Ultrafast Air Self-Charging Zinc Battery

Air self-charging power systems possess the capability of energy harvesting, conversion, and storage simultaneously. However, in general, their self-charging rate is slow and the batteries cannot be oxidized to the fully charged state due to the weak oxidizability of O2 . Herein, an ultrafast air self-charging aqueous zinc battery is designed by constructing a polyaniline@Pt/C (PANI@Pt/C) composite cathode. The introduction of Pt/C catalyst endows the redox reaction between PANI and O2 with fast reaction kinetics and extended redox potential difference. Therefore, the self-charging rate of the Zn/PANI@Pt/C batteries is effectively accelerated and they can be self-charged to fully charged state. Furthermore, the PANI can be recharged by O2 simultaneously during discharging process to compensate the consumed electrical energy, achieving prolonged energy supply. In addition, the PANI@Pt/C cathodes can be directly used as the cathodes of flexible self-charging zinc batteries due to their excellent mechanical properties. As a proof of concept, flexible soft-packaged Zn/PANI@Pt/C batteries are fabricated and displayed stable electrochemical performance and self-rechargeability even at different bending states. A route is provided here to design ultrafast chemical self-charging energy storage devices and the horizons of flexible energy storage devices are broadened.

Acidic Metal-Based Functional Ionic Liquids Catalyze the Synthesis of Bio-Based PEF Polyester

Utilizing triethylenediamine (DA), 1,3-propanesultone (PS), whose ring opens during the formation of the dizwiterion-intermediate DA-2PS, and the metal chlorides XCly, where X = Sn(IV), Zn(II),Al(III), Fe(III) and Mn(II), are used for the synthesis of five kinds of acidic metal-based functionalized ionic liquid catalysts ([DA-2PS][XCly]2). Their chemical structures, thermal stability and dual acidic active site were analyzed. We investigated the performance of [DA-2PS][XCly]2 in catalyzing the esterification reaction between 2,5-furandicarboxylic acid (FDCA) and ethylene glycol (EG) to synthesize poly (ethylene 2,5-furandicarboxylate)(PEF). Among the catalysts tested, [DA-2PS][SnCl5]2 exhibited the best catalytic performance under identical process parameters, and the optimal catalyst dosage was determined to be 0.05 mol% based on FDCA. The optimal conditions for the reaction were predicted using response surface methodology: a feed ratio of EG:FDCA = 1.96:1, an esterification temperature of 219.86 °C, a polycondensation temperature of 240.04 °C and a polycondensation time of 6.3 h, with a intrinsic viscosity of 0.67 dL·g-1. The resulting PEF was experimentally verified to exhibit an intrinsic viscosity of 0.68 dL·g-1 and a number average molecular weight of 28,820 g·mol-1. Finally, the structure and thermal properties of PEF were characterized. The results confirmed that PEF possessed the correct structure, exhibited high thermal stability and demonstrated excellent thermal properties.

Bayesian Optimization of Wet-Impregnated Co-Mo/Al2O3 Catalyst for Maximizing the Yield of Carbon Nanotube Synthesis

Multimetallic catalysts have demonstrated their high potential for the controlled synthesis of carbon nanotubes (CNTs), but their development requires a more complicated optimization than that of monometallic catalysts. Here, we employed Bayesian optimization (BO) to optimize the preparation of Co-Mo/Al2O3 catalyst using wet impregnation, with the goal of maximizing carbon yield in the chemical vapor deposition (CVD) synthesis of CNTs. In the catalyst preparation process, we selected four parameters to optimize: the weight percentage of metal, the ratio of Co to Mo in the catalyst, the drying temperature, and the calcination temperature. We ran two parallel BO processes to compare the performance of two types of acquisitions: expected improvement (EI), which does not consider noise, and one-shot knowledge gradient (OKG), which takes noise into account. As a result, both acquisition functions successfully optimized the carbon yield with similar performance. The result suggests that the use of EI, which has a lower computational load, is acceptable if the system has sufficient robustness. The investigation of the contour plots showed that the addition of Mo has a negative effect on carbon yield.

Self-Supported Spray-Coated NiFe-LDH Catalyst on a Stainless Steel Substrate for Efficient Oxygen Evolution Reaction

In the quest for more efficient and cost-effective electrocatalytic systems, careful selection of catalysts and substrates plays a pivotal role. This study introduces an approach by synthesizing and depositing NiFe-layered double hydroxide (NiFe-LDH) catalysts on commercial AISI 304 substrates by using a low-temperature spray-coating technique. Through systematic investigations, the influence of processing conditions, such as the synthesis, ultrasonic power for having a stable nanoparticle's dispersion, and spray cycle optimization on the electrochemical and morphological properties of the coatings, is thoroughly explored. The results showcase exceptional catalytic performance, achieving an overpotential of 230 mV at 10 mA/cm2, with enhanced stability even at high current densities of 500 mA/cm2. The study highlights the significance of meticulous processing optimization and presents a scalable methodology that holds great potential for developing catalysts for oxygen evolution reactions (OER) and facilitates their integration into industrial processes.

Enhancing Aqueous Chlorate Reduction Using Vanadium Redox Cycles and pH Control

Chlorate (ClO3-) is a toxic oxyanion pollutant from industrial wastes, agricultural applications, drinking water disinfection, and wastewater treatment. Catalytic reduction of ClO3- using palladium (Pd) nanoparticle catalysts exhibited sluggish kinetics. This work demonstrates an 18-fold activity enhancement by integrating earth-abundant vanadium (V) into the common Pd/C catalyst. X-ray photoelectron spectroscopy and electrochemical studies indicated that VV and VIV precursors are reduced to VIII in the aqueous phase (rather than immobilized on the carbon support) by Pd-activated H2. The VIII/IV redox cycle is the predominant mechanism for the ClO3- reduction. Further reduction of chlorine intermediates to Cl- could proceed via VIII/IV and VIV/V redox cycles or direct reduction by Pd/C. To capture the potentially toxic V metal from the treated solution, we adjusted the pH from 3 to 8 after the reaction, which completely immobilized VIII onto Pd/C for catalyst recycling. The enhanced performance of reductive catalysis using a Group 5 metal adds to the diversity of transition metals (e.g., Cr, Mo, Re, Fe, and Ru in Groups 6-8) for water pollutant treatment via various unique mechanisms.

Rhodium and Carbon Sites with Strong d-p Orbital Interaction for Efficient Bifunctional Catalysis

Efficient and stable catalysts are highly desired for the electrochemical conversion of hydrogen, oxygen, and water molecules, processes which are crucial for renewable energy conversion and storage technologies. Herein, we report the development of hollow nitrogenated carbon sphere (HNC) dispersed rhodium (Rh) single atoms (Rh1HNC) as an efficient catalyst for bifunctional catalysis. The Rh1HNC was achieved by anchoring Rh single atoms in the HNC matrix with an Rh-N3C1 configuration, via a combination of in situ polymerization and carbonization approach. Benefiting from the strong metal atom-support interaction (SMASI), the Rh and C atoms can collaborate to achieve robust electrochemical performance toward both the hydrogen evolution and oxygen reduction reactions in acidic media. This work not only provides an active site with favorable SMASI for bifunctional catalysis but also brings a strategy for the design and synthesis of efficient and stable bifunctional catalysts for diverse applications.

Atomic Layer Deposition of Cu Electrocatalysts on Gas Diffusion Electrodes for CO2 Reduction

Electrochemical reduction of CO2 using Cu catalysts enables the synthesis of C2+ products including C2H4 and C2H5OH. In this study, Cu catalysts were fabricated using plasma-enhanced atomic layer deposition (PEALD), achieving conformal deposition of catalysts throughout 3-D gas diffusion electrode (GDE) substrates while maintaining tunable control of Cu nanoparticle size and areal loading. The electrochemical CO2 reduction at the Cu surface yielded a total Faradaic efficiency (FE) > 75% for C2+ products. Parasitic hydrogen evolution was minimized to a FE of ∼10%, and a selectivity of 42.2% FE for C2H4 was demonstrated. Compared to a line-of-sight physical vapor deposition method, PEALD Cu catalysts show significant suppression of C1 products compared to C2+, which is associated with improved control of catalyst morphology and conformality within the porous GDE substrate. Finally, PEALD Cu catalysts demonstrated a stable performance for 15 h with minimal reduction in the C2H4 production rate.

Fe2O3/Ni Nanocomposite Electrocatalyst on Cellulose for Hydrogen Evolution Reaction and Oxygen Evolution Reaction

A key challenge in the development of sustainable water-splitting (WS) systems is the formulation of electrodes by efficient combinations of electrocatalyst and binder materials. Cellulose, a biopolymer, can be considered an excellent dispersing agent and binder that can replace high-cost synthetic polymers to construct low-cost electrodes. Herein, a novel electrocatalyst was fabricated by combining Fe2O3 and Ni on microcrystalline cellulose (MCC) without the use of any additional binder. Structural characterization techniques confirmed the formation of the Fe2O3-Ni nanocomposite. Microstructural studies confirmed the homogeneity of the ~50 nm-sized Fe2O3-Ni on MCC. The WS performance, which involves the hydrogen evolution reaction (HER) and the oxygen evolution reaction (OER), was evaluated using a 1 M KOH electrolyte solution. The Fe2O3-Ni nanocomposite on MCC displayed an efficient performance toward lowering the overpotential in both the HER (163 mV @ 10 mA cm-2) and OER (360 mV @ 10 mA cm-2). These results demonstrate that MCC facilitated the cohesive binding of electrocatalyst materials and attachment to the substrate surface. In the future, modified cellulose-based structures (such as functionalized gels and those dissolved in various media) can be used as efficient binder materials and alternative options for preparing electrodes for WS applications.

The ability of drinking water treatment sludge to degrade methylene blue in water through combined adsorption/photo Fenton-like process

In the present study, drinking water treatment sludge (DWTS) was reused as a catalyst in advanced oxidation processes for the removal of methylene blue (MB) from aqueous solutions. After determining their chemical and mineralogical compositions by X-ray Powder Diffraction (XRD), BET surface area, scanning electron microscopy with energy dispersive spectroscopy (SEM/EDS), Inductively Coupled Plasma (ICP), and FT-IR spectra. DWTS has been used as a heterogeneous photo Fenton-Like catalyst for the oxidation of MB under different parameters, including pH (3-6), H2O2 concentration (9.79-29.37 mM), and dose (1-2.5 g/L). The results showed that within 180 min and under UV light irradiation, more than 86% of MB having a concentration of 50 mg/L were removed using a catalyst loading of 1.5 g/L, a H2O2 dosage of 23.17 mM and a solution pH of 5. The DWTS has a satisfactory stability as the catalyst is stable and have very less iron leaching property.

Discovery of Graphene Growth Alloy Catalysts Using High-Throughput Machine Learning

Despite today's commercial-scale graphene production using chemical vapor deposition (CVD), the growth of high-quality single-layer graphene with controlled morphology and crystallinity remains challenging. Considerable effort is still spent on designing improved CVD catalysts for producing high-quality graphene. Conventionally, however, catalyst design has been pursued using empirical intuition or trial-and-error approaches. Here, we combine high-throughput density functional theory and machine learning to identify new prospective transition metal alloy catalysts that exhibit performance comparable to that of established graphene catalysts, such as Ni(111) and Cu(111). The alloys identified through this process generally consist of combinations of early- and late-transition metals, and a majority are alloys of Ni or Cu. Nevertheless, in many cases, these conventional catalyst metals are combined with unconventional partners, such as Zr, Hf, and Nb. The approach presented here therefore highlights an important new approach for identifying novel catalyst materials for the CVD growth of low-dimensional nanomaterials.

Recent Progress in Catalyst Development of the Hydrogenolysis of Biomass-Based Glycerol into Propanediols-A Review

The use of biomass-based glycerol to produce chemicals with high added value is of great significance for solving the problem of glycerol surplus and thus reducing the production cost of biodiesel. The production of 1,2-propanediol (abbreviated as 1,2-PDO) and 1,3-propanediol (abbreviated as 1,3-PDO) via the hydrogenolysis of glycerol is one of the most representative and highest-potential processes for the comprehensive utilization of biomass-based glycerol. Glycerol hydrogenolysis may include several parallel and serial reactions (involving broken C-O and C-C bonds), and therefore, the catalyst is a key factor in improving the rate of glycerol hydrogenolysis and the selectivities of the target products. Over the past 20 years, glycerol hydrogenolysis has been extensively investigated, and until now, the developments of catalysts for glycerol hydrogenolysis have been active research topics. Non-precious metals, including Cu, Ni, and Co, and some precious metals (Ru, Pd, etc.) have been used as the active components of the catalysts for the hydrogenolysis of glycerol to 1,2-PDO, while precious metals such as Pt, Rh, Ru, Pd, and Ir have been used for the catalytic conversion of glycerol to 1,3-PDO. In this article, we focus on reviewing the research progress of the catalyst systems, including Cu-based catalysts and Pt-, Ru-, and Pd-based catalysts for the hydrogenolysis of glycerol to 1,2-PDO, as well as Pt-WOx-based and Ir-ReOx-based catalysts for the hydrogenolysis of glycerol to 1,3-PDO. The influence of the properties of active components and supports, the effects of promoters and additives, and the interaction and synergic effects between active component metals and supports are also examined.

Direct Application of Carbon Nanotubes (CNTs) Grown by Chemical Vapor Deposition (CVD) for Integrated Circuits (ICs) Interconnection: Challenges and Developments

With the continuous shrinkage of integrated circuit (IC) dimensions, traditional copper interconnect technology is gradually unable to meet the requirements for performance improvement. Carbon nanotubes have gained widespread attention and research as a potential alternative to copper, due to their excellent electrical and mechanical properties. Among various methods for producing carbon nanotubes, chemical vapor deposition (CVD) has the advantages of mild reaction conditions, low cost, and simple reaction operations, making it the most promising approach to achieve compatibility with integrated circuit manufacturing processes. Combined with through silicon via (TSV), direct application of CVD-grown carbon nanotubes in IC interconnects can be achieved. In this article, based on the above background, we focus on discussing some of the main challenges and developments in the application of CVD-grown carbon nanotubes in IC interconnects, including low-temperature CVD, metallicity enrichment, and contact resistance.

Prediction of Higher Heating Values in Bio-Oil from Solvothermal Biomass Conversion and Bio-Oil Upgrading Given Discontinuous Experimental Conditions

Both the conversion of lignocellulosic biomass to bio-oil (BO) and the upgrading of BO have been the targets of many studies. Due to the large diversity and discontinuity seen in terms of reaction conditions, catalysts, solvents, and feedstock properties that have been used, a comparison across different publications is difficult. In this study, machine learning modeling is used for the prediction of final higher heating value (HHV) and ΔHHV for the conversion of lignocellulosic feedstocks to BO, and BO upgrading. The models achieved coefficient of determination (R2) scores ranging from 0.77 to 0.86, and the SHapley Additive exPlanations (SHAP) values were used to obtain model explainability, revealing that only a few experimental parameters are largely responsible for the outcome of the experiments. In particular, process temperature and reaction time were overwhelmingly responsible for the majority of the predictions, for both final HHV and ΔHHV. Elemental composition of the starting feedstock or BO dictated the upper possible HHV value obtained after the experiment, which is in line with what is known from previous methodologies for calculating HHV for fuels. Solvent used, initial moisture concentration in BO, and catalyst active phase showed low predicting power, within the context of the data set used. The results of this study highlight experimental conditions and variables that could be candidates for the creation of minimum reporting guidelines for future studies in such a way that machine learning can be fully harnessed.

Effect of Yttrium on Ce/Ni-Metakaolin Catalysts for CO2 Methanation

In recent years, major economies have implemented carbon reduction and carbon neutrality policies. Furthermore, with advancements in science and technology, carbon dioxide (CO2) is now considered a valuable raw material for producing carbon-based fuels through hydrogenation. Various concentrations of yttrium (referred to as Y hereafter) were introduced to assess their influence on the catalytic performance of CO2 methanation. At a temperature of 300 °C, the catalyst exhibited an impressive CO2 conversion rate of 78.4% and maintained remarkable stability throughout a rigorous 100 h stability assessment. The findings suggest that the inclusion of yttrium (Y) promotes the formation of oxygen vacancies and alkaline sites on the catalyst. This, in turn, enhances the reducibility of nickel species, improves the dispersion of nickel particles, and plays a pivotal role in enhancing thermal stability. Furthermore, it offers an innovative design approach for creating highly efficient composite CO2 methanation catalysts by controlling particle size and harnessing synergistic catalytic effects at the metal/support interface.

Propylene Metathesis over Molybdenum Silicate Microspheres with Dispersed Active Sites

In this work, we demonstrate that amorphous and porous molybdenum silicate microspheres are highly active catalysts for heterogeneous propylene metathesis. Homogeneous molybdenum silicate microspheres and aluminum-doped molybdenum silicate microspheres were synthesized via a nonaqueous condensation of a hybrid molybdenum biphenyldicarboxylate-based precursor solution with (3-aminopropyl)triethoxysilane. The as-prepared hybrid metallosilicate products were calcined at 500 °C to obtain amorphous and porous molybdenum silicate and aluminum-doped molybdenum silicate microspheres with highly dispersed molybdate species inserted into the silicate matrix. These catalysts contain mainly highly dispersed MoOx species, which possess high catalytic activity in heterogeneous propylene metathesis to ethylene and butene. Compared to conventional silica-supported MoOx catalysts prepared via incipient wetness impregnation (MoIWI), the microspheres with low Mo content (1.5-3.6 wt %) exhibited nearly 2 orders of magnitude higher steady-state propylene metathesis rates at 200 °C, approaching site time yields of 0.11 s-1.