Does an alteration of dialyzer design and geometry affect biocompatibility parameters?

The aim of the study was to assess the biocompatibility profile of a newly developed high-flux polysulfone dialyzer type (FX-class dialyzer). The new class of dialyzers incorporates a number of novel design features (including a new membrane) that have been developed specifically in order to enhance the removal of small- and middle-size molecules. The new FX dialyzer series was compared with the classical routinely used high-flux polysulfone F series of dialyzers. In an open prospective, randomized, crossover clinical study, concentrations of the C5a complement component, and leukocyte count in blood and various thrombogenicity parameters were evaluated before, and at 15 and 60 min of hemodialysis at both dialyzer inlet and outlet in 9 long-term hemodialysis patients using the FX60S dialyzers and, after crossover, the classical F60S, while in another 9 patients, the evaluation was made with the dialyzers used in reverse order. The comparison of dialyzers based on evaluation of the group including all procedures with the FX60S and the group including procedures with the F60S did not reveal significant differences in platelet count, activated partial thromboplastin times, plasma heparin levels, platelet factor-4, D-dimer, C5a, and leukocyte count at any point of the collecting period. Both dialyzer types showed a significant increase in the plasma levels of the thrombin-antithrombin III complexes; however, the measured levels were only slightly elevated compared with the upper end of the normal range. Biocompatibility parameters reflecting the behavior of platelets, fibrinolysis, complement activation, and leukopenia do not differ during dialysis with either the FX60S or the F60S despite their large differences in design and geometry features. Although coagulation activation, as evaluated by one of the parameters used, was slightly higher with the FX60S, it was still within the range seen with other highly biocompatible dialyzers and therefore is not indicative of any appreciable activation of the coagulation system. Thus, the incorporation of various performance-enhancing design features into the new FX class of dialyzers does not result in a deterioration of their biocompatibility profile, which is comparable to that of the classical F series of dialyzers.

Relation between Different Treatment Modalities and Genomic Damage of End-Stage Renal Failure Patients

BACKGROUND

Patients with end-stage renal disease display enhanced genomic damage. We investigated the relation between genomic damage and different treatment modalities.

METHODS

In a longitudinal study two groups of patients were analyzed in monthly intervals. We assessed the initiation of hemodialysis in 5 conservatively treated patients, and a switch from hemodialysis to hemodiafiltration in 7 patients. DNA damage was investigated in peripheral blood lymphocytes by micronucleus frequency and by comet assay analysis. With regard to potential genotoxicity of advanced glycation end products (AGEs), levels of imidazolone A and AGE-associated fluorescence (AGE-FL) were determined.

RESULTS

The initiation of hemodialysis did not alter the genomic damage. In patients who switched from hemodialysis to hemodiafiltration, a small but significant reduction in the comet assay but not in the micronucleus frequency was observed. Elevated plasma levels of imidazolone A and AGE-FL were not influenced by the treatment modalities.

CONCLUSION

In our small patient group no major reduction of the elevated genomic damage could be reached. Disease factors not influenced by altered dialysis modalities may have contributed considerably in our patient group. The persisting high levels of DNA damage suggest a need for further improvement. Inhibiting AGE formation may be one promising way for the future.

Effect of Different Hemodialysis Regimens on Genomic Damage in End-Stage Renal Failure

Patients with end-stage renal disease display enhanced genomic damage that may have pathophysiologic relevance for cancer development and cardiovascular complications. We investigated to what extent the genomic damage in peripheral blood lymphocytes can be modulated #1: by initiation of standard hemodialysis (SHD) in formerly conservatively treated end-stage renal disease patients, #2: by a switch from SHD to hemodiafiltration, and #3: daily dialysis (DHD). Genomic damage was evaluated by the micronuclei (MN) frequency test and the comet assay (CA). In a prospective study we found that initiation of SHD did not induce significant changes of genomic damage in peripheral blood lymphocytes whereas the change to hemodiafiltration improved the percentage of DNA in the tail as measured by CA without modulating the MN frequency. In a cross-sectional investigation the degree of genomic damage as evaluated by MN frequency was significantly lower in a patient group treated by DHD as compared with a group treated by SHD. In the DHD patients there also was a significant decrease of the plasma concentrations of urea and the advanced glycation end products imidazolone A, carboxymethyllysine, and of advanced glycation end product-associated fluorescence.

Genomic damage and circulating AGE levels in patients undergoing daily versus standard haemodialysis

BACKGROUND

Patients with end-stage renal failure, whether on conservative or haemodialysis therapy, have a high incidence of DNA damage. It is not known if improved control of the uraemic state by daily haemodialysis (DHD) reduces DNA lesions.

METHODS

DNA damage in peripheral blood lymphocytes (PBLs) was evaluated in a cross-sectional study of 13 patients on DHD (2-3 h, 6 times/week), 12 patients on standard haemodialysis (SHD) therapy (4-5 h, 3 times/week) and 12 healthy age-matched volunteer controls. The biomarker of DNA damage used was micronucleus frequency. The assessed plasma parameters of microinflammation and oxidative stress were C-reactive protein (CRP), interleukin-6 (IL-6), neopterin, advanced oxidation protein products (AOPP), and homocysteine. We also measured plasma concentrations of the circulating advanced glycation end products (AGEs) MGI (methylglyoxal-derived imidazolinone), CML (carboxymethyllysine), imidazolone A (3-deoxyglucosone-derived imidazolinone) and AGE-associated fluorescence.

RESULTS

Compared to SHD, DHD was associated with significantly lower DNA damage, approaching the normal range. Micronuclei (MN) frequency averaged 29.1 MN+/-5.9/1000 binucleated (BN) cells in the SHD group, which is significantly elevated (P<0.01), 14.8 MN+/-4.0/1000 BN cells in the DHD group, and 13.2 MN+/-3.04/1000 BN cells in the controls. CRP and AOPP were in the normal range (and similar between the dialysis groups). In contrast, IL-6 and neopterin were significantly elevated, with lower values associated with DHD as compared with SHD. The increased levels of AGEs tended to be lower in the DHD group, reaching significance for CML and imidazolone A.

CONCLUSIONS

Overall, it was found that genomic damage in PBLs is lower in patients on DHD than in those on SHD. Lower plasma concentrations of uraemic toxins, including circulating AGEs, may account for the differences. To confirm these data, prospective clinical trials need to be performed.

Prediction of cardiovascular risk in hemodialysis patients by data mining

OBJECTIVES

The objective of this work was to contribute to the development, validation and application of data mining methods for prediction in decision support systems in medicine. The particular focus was on the prediction of cardiovascular risk factors in hemodialysis patients, specifically the interventricular septum (IVS) thickness of the heart of individual patients as an important quantitative indicator to diagnose left ventricular hypertrophy. The work was based on data from 63 long-term hemodialysis patients of the KfH Dialysis Centre in Jena, Germany.

METHODS

The approach applied is based on data mining methods and involves four major steps: data based clustering, cluster based rule extraction, rulebase construction and cluster and rule based prediction. The methods employed include crisp and fuzzy algorithms. At each step, logical and medical validation of results was carried out. Different sets of randomly selected patient data were used to train, test and optimize the clusterbases and rulebases for prediction.

RESULTS

Using the best clusterbase/rulebase combination designed, the IVS thickness cluster ('small' or 'large') was predicted correctly for 30 of the 35 patients with known IVS values in the training data set; no patient was predicted incorrectly and 5 were parity predicted. For the test data set, 4 of the 6 patients with known IVS values were predicted correctly, no patient incorrectly and 2 parity. These results did not substantially differ from those obtained using the second best clusterbase/rulebase combination which was finally recommended for use based on further performance criteria. The prediction of the IVS thickness clusters of the 22 patients with unknown IVS values also yielded good results that were (and could only be) validated by a medical individual risk assessment of these patients.

CONCLUSIONS

The approach applied proved successful for the cluster and rule based prediction of a quantitative variable, such as IVS thickness, for individual patients from other variables relevant to the problem. The results obtained demonstrate the high potential of the approach and the methods developed and validated to support decision-making in hemodialysis and other fields of medicine by individual risk prediction.

Extracorporeal liver support: porcine or human cell based systems?

Initial results of the clinical use of primary porcine liver cells for extracorporeal liver support are being reviewed as the cell source is controversial. According to Eurotransplant data 20-25% of explanted donor livers are not transplanted, due to factors such as steatosis or cirrhosis. This number corresponds to the number of patients with acute liver failure who require bridging therapy to transplantation. Primary human liver cells from transplant discards can be isolated, purified and maintained in bioreactors and provide an alternative for cell-based extracorporeal liver support therapy. A four-compartment bioreactor enables recovery from preservation and isolation injury in a three-dimensional network of interwoven capillary membranes with integrated oxygenation, rendering the liver cells from these discarded donor organs viable for clinical utilization. Patient contact with additional animal-derived biomatrix and fetal calf serum can be avoided. The initiation of an in vitro cultivation phase allows cell stabilization, quality control, and immediate availability of a characterized system without cryopreservation. The hypothesis of this paper is that with appropriate logistics and four-compartment bioreactor technology, cells from human liver transplant discards can serve the demand for cell-based therapy, including extracorporeal liver support.

Verification of the chemical composition and specifications of haemodialysis membranes by NMR and GPC-FTIR-coupled spectroscopy

The chemical composition of a dialysis membrane is decisive towards determining its physical and biochemical properties--two fundamental determinants of the success of therapy offered to patients suffering from chronic renal failure. From the vast variety of synthetic polymers available, only a few are suitable for the manufacture of dialysis membranes that have to conform to the diverse demands of modern haemodialysis and related therapies. Recently, a membrane labelled as polyamide (Polyamide S) has caused some confusion to end-users in that the product specification for the membrane is given as 'polyarylethersulfone' or simply as Polyamide S membrane. As the chemical and physical properties of these two polymer types are distinctly different, it is unclear whether the functional characteristics of Polyamide S are to be attributed to polyamide, polyarylethersulfone, or, to both polymers. We therefore undertook investigations to ascertain the exact chemical nature of the Polyamide S membrane using a series of chemical analytical tools and an appropriate polyamide reference. The analytical techniques were conventional gel permeation chromatography (GPC), GPC-FTIR coupled spectroscopy using dimethyl acetamide and hexafluoroisopropanol as solvents and nuclear magnetic resonance spectroscopy. Glass transition temperature measurements and quantitative elemental analysis were also carried out. None of the analytical techniques used showed any traces of polyamide in Polyamide S; no aliphatic or aromatic polyamide chemical entities were detected in any of the samples tested. The Polyamide S dialysis membrane thus comprises, solely, of polyarylethersulfone, which is also known as polyethersulfone.

Plasma levels of advanced glycation end products during haemodialysis, haemodiafiltration and haemofiltration: potential importance of dialysate quality

BACKGROUND

Advanced glycation end products (AGEs) accumulate in patients with end-stage renal disease (ESRD). The aim of this study was to investigate the potential influence of different modalities of renal replacement therapies on plasma AGE levels.

METHODS

The removal of AGEs by high-flux haemodialysis (HD) using standard and ultrapure dialysis fluid (SDF and UDF), by haemodiafiltration (HDF) and by haemofiltration (HF) was studied by fluorescence spectroscopy and by a carboxymethyllysine (CML)-specific ELISA. In addition, molecular weight distribution of fluorescent AGE products in serum of several patients was analysed by gel filtration.

RESULTS

The highest AGE-typical fluorescence was found in the serum of patients on HD using SDF (114,667+/-18,967 arbitrary units (AU)), followed by patients on HDF (86,912+/-24,411 AU, P<0.005), by patients on HD using UDF (74,953+/-21,152 AU, P<0.0001) and by patients on HF (74 039+/-17 027 AU, P<0.0001). Similar results were found for serum CML levels with the highest values in HD patients on SDF (1609+/-504 ng/ml), followed by patients on HF (1354+/-614 ng/ml, P<0.001), then by HD patients on UDF (1310+/-403 ng/ml, P<0.001) and by patients on HDF (1132+/-338 ng/ml, P<0.001). The removal rate of AGEs, as evaluated by the determination of the pre-/post-dialysis AGE differences, was comparable across all groups.

CONCLUSION

These findings suggest that factors other than removal are responsible for the lower pre-dialysis AGE levels found in patients on convective dialysis as well as on HD with UDF. A role of water quality is assumed. This is corroborated by the finding that the high molecular weight AGE-fraction is preferentially lowered in comparison with patients on HD with SDF, as analysed by gel filtration chromatography. These findings could be best explained by a less severe oxidative stress (i.e. resulting in decreased AGE generation) with HF and HDF, as well as with ultrapure HD.

Validation of a two-pool model for the kinetics of beta2-microglobulin

Secondary amyloidosis due to beta-2-microglobulin (beta2-m) is a serious long-term complication in patients on regular dialysis therapy. Beta2-m can be considered a middle-molecule marker used to facilitate the assessment of dialysis efficacy. For this purpose, a validated model that calculates characteristic efficacy parameters, such as Kt/V, TAC and generation rate, is needed. There is general agreement that beta2-m-kinetics should be described by a two-pool model, but little has been published to validate such an approach. We measured the beta2-m concentration profiles of eight stable patients during hemodialysis (HD) at the start of treatment, after 30 minutes, after 60 minutes, and every hour until the end. Thereafter they were measured at 10-minute intervals for an hour. The dialyser clearances were determined from the plasma concentrations in front of and behind the dialyser twice during each session - after 1 hour, and 4 hours from the start of treatment. The kinetic parameters of a two-pool model (e.g. the compartment volumes V1 and V2, the mass transfer coefficient K12 and the generation rate G) were determined from the optimal fit of the measured concentration profile. The table below summarises the results by giving the mean and standard deviation for each parameter: [table: see text]. Inter-individual differences in V1/V2 and K12 were high, ranging from 2.5 to 10.0 for V/V2 and from 26 to 140 for K12. Error analysis suggested that these wide ranges were due to the method and that in reality the probable range of V is 25-36% of TBW, of V1/V2 3.5-5.3, and of K12 30-80 ml/min. With standard values for these three parameters (V = 30% of TBW, V/V2 = 4.4 and K12 = 55 ml/m), equal for all patients, and their respective ranges, Kt/W can be calculated with a standard deviation of 13%. Kt/W > 1.2 secures the maximum possible beta2-m removal with three HD treatments a week.

CONCLUSIONS

The parameters of a two-pool model of beta2-m kinetics can be derived from concentration profiles obtained under routine dialysis conditions, but accuracy is not completely satisfactory. Similar to the dialysis dose for urea (Kt/Vurea) the dialysis dose for beta2-m (Kt/Vbeta2-m) can be calculated from the pre- and post-dialysis concentrations of beta2-m, body weight, ultrafiltration and dialysis time. Kt/Vbeta2-m > 1.2 secures the maximum possible removal of beta2-m in HD with three sessions per week.

Polymers in nephrology. Characteristics and needs

Polymers employed as biomaterials in nephrology serve for different applications: they form membranes for dialysis and plasmapheresis, are used as materials for dialyser housings and as a potting mass for capillary membranes, they make up tubing-systems for extracorporeal circuits and - in the form of beads - act as parts of adsorber columns for hemoperfusion or immunoadsorption. However, generally speaking, many polymers have not yet been designed for their final application. To date, many polymers are still taken from the chemist's shelf according to their alleged performance properties or to their sterilisability. When used in medical application, polymers must show a high purity. Uncontrolled leaching of oligomers from the polymer backbone or of additives from or during the manufacturing process must be avoided. Blood and other body fluids are extremely effective in extracting any loosely bound polymers. During long-term application, e.g. in patients suffering from chronic diseases, these effects may lead to an accumulation of these compounds in circulating blood, tissue, or joints. Consequently, polymers should show an excellent biostability and not degrade during their ageing process. The amount of extractable material should be kept low in order to avoid inflammatory reactions. Polymers must have high blood compatibility in terms of minimized cell- and complement activation. Polymers for medical application should at best be able to stand high temperatures in order to survive steam sterilisation. If this is impossible, their release kinetics for residual quantities of sterilizing agents should be fast. Finally, protein adsorption should appear under controlled conditions, otherwise a reduced performance through protein adsorption will take place. Further, the uncontrolled activation of biochemical cascades, such as the coagulation, complement or contact phase cascade, following blood/material contact must be minimized. A final aspect has been recently made responsible for adverse patients reactions, the interaction between polymers and medicinal drugs. This drug/material interaction must be low, at best zero, apart form those situations, where a controlled drug-release is wanted. The chemical variety of polymers for medical application is large. However, all typical requirements cannot be met by one single polymer. Compromises have to be found between properties and application. Polymer selection for application in nephrology has always to be made under the premise of final application.

In vitro evaluation of the hydraulic permeability of polysulfone dialysers

An in vitro set-up has been designed to study the hydraulic permeability of hollow fiber dialysers. Forward and reverse dialysate ultrafiltration were determined using both sterile dialysers and samples with a protein layer settled on the membrane (Fresenius F6, F8, F60 and F80). The ultrafiltration coefficient KUF (ml/h.mmHg) was calculated as the ratio of volumetrical flow (QUF) and transmembrane pressure (TMP) measurements. The protein layer on the membrane was induced either by recirculating human plasma through the dialysers (in vitro) or by a standard hemodialysis session (in vivo). KUF is largely independent of TMP up to 600mmHg (low flux) and 60mmHg (high flux) for forward and reverse flow In sterile dialysers, backfiltration yields a significantly different KUF except for the F80. An in vitro induced protein layer on the membrane decreases KUF15-30% (forward) and 4-12% (backward) in low flux and 45-70% (forward) and 65-73% (backward) in high flux dialysers.

Does treatment modality have an impact on anemia in patients with chronic renal failure? Effect of low- and high-flux biocompatible dialysis

Renal anemia significantly affects the morbidity and mortality of dialysis patients. The aim of the present study was to establish whether the severity of anemia and success of its treatment differs when using high-flux (HF) or low-flux (LF) hemodialysis. Twenty-five patients on long-term hemodialysis with a mean hematocrit (Hct) of 33%, S alb of 36 g/L, and Kt/V urea of 1.5 were divided into Groups X (n = 13) and Y (n = 12) in a prospective randomized crossover study. Group X was initially treated with LF hemodialysis to be followed by HF hemodialysis for 8 weeks each time. Group Y started with 8 week HF hemodialysis and continued, after crossover, with 8 weeks of LF hemodialysis. HF and LF hemodialysis were performed with polysulfone dialyzers F 7HPS and F60S (Fresenius Medical Care, Bad Homburg, Germany). Hct values, examined at 2 week intervals, did not differ significantly between Groups X and Y during 16 weeks of the study at any measuring interval. In another analysis, all results of HF hemodialysis (first 8 weeks of Y + second 8 weeks of X) were pooled as were all data of LF hemodialysis (first 8 weeks of X + second 8 weeks of Y). No significant relationships were noted between duration of treatment with HF hemodialysis and Hct (n = 72, rS = 0.11, p = 0.36) and between duration of LF hemodialysis and Hct (n = 74, rS = 0.02, p = 0.87) in the newly formed groups. The Hct measured during HF hemodialysis and LF hemodialysis did not differ significantly. Analysis of variance did not reveal a relationship between Hct and the HF or LF membrane. As HF and LF hemodialysis differed significantly in Kt/V urea, the variables were adjusted to identical Kt/V urea using analysis of covariance. No relationship between Hct and dialysis membrane permeability was demonstrated even in this case. Use of biocompatible LF and HF membranes in standard hemodialysis modes under conditions of adequate dose of dialysis and the time period studied did not result in different effects on anemia.

The influence of different glucose concentrations in haemodialysis solutions on metabolism and blood pressure stability in diabetic patients

In recent years the percentage of diabetic patients on haemodialysis has increased. Considering the high frequency of intradialytic hypotensive and hypoglycaemic episodes experienced by these patients, it was the aim of the present study to evaluate the influence of different dialysate glucose concentrations (5.5 mmol/L or 11 mmol/L) on blood pressure and glycaemic regulation, using special dialysis equipment - the GENIUS System. This cross-over, prospective and randomised study, total duration 14 weeks, included 20 diabetic patients on maintenance haemodialysis. Group 1: 9 patients dialysed using dialysate with a glucose concentration of 5.5 mmol/L and after 7 weeks switched to dialysate with a glucose concentration of 11 mmol/L. Group 2: vice versa. Results show a statistically higher number of patients with hypoglycaemic and hypotensive episodes using dialysate with a 5.5 mmol/L glucose concentration. Also, mean serum glucose values were higher during haemodialysis sessions with a glucose dialysate concentration of 11 mmol/L. There were no statistical differences between the groups in laboratory values, HbA1C, insulin doses or in anthropometric parameters. Our results suggest that fewer diabetic patients undergoing haemodialysis using a higher dialysate glucose concentration of 11 mmol/L have hypoglycaemic and hypotensive episodes. Since this dialysate glucose concentration had no influence on lipid or hepatic metabolism, anthropometric parameters and especially HbA/1C values in this short-term study, the long term examination of its effects is warranted.

Comet-assay analysis identifies genomic damage in lymphocytes of uremic patients

This study investigates genomic damage in peripheral lymphocytes from patients with moderate to severe chronic renal insufficiency and those on long-term maintenance hemodialysis (MHD) and hemodiafiltration therapy. As a measure for genomic damage, the comet assay (single-cell gel electrophoresis) was applied. This test detects single- and double-strand breaks and alkali labile sites through electrophoretic mobility of the resulting fragments. The average damage (percentage of DNA in the tail region of the comet) observed in cells of the control group of 21 healthy subjects was 10.5% +/- 0.8%. There was a significant increase to 14.7% +/- 3.5% in cells of 23 patients with chronic renal failure, and a further increase to 17.1% +/- 3.5% in the subgroup of 12 patients with serum creatinine values greater than 6 mg/dL. Damage was 16.7% +/- 4.2% in cells of the MHD group (26 patients) and 20.1% +/- 3.0% in the subgroup with MHD therapy longer than 10 years (8 patients). Cellular DNA damage in the group of 15 maintenance hemodiafiltration patients was 15.6% +/- 2.1%, ranging between predialysis and MHD patients, and did not seem to increase with treatment time. These results, together with previously observed elevated frequencies of micronuclei, decreased DNA repair, and increased cancer incidence described for these patient groups, emphasize the need to further optimize the current therapy for reducing the degree of genomic damage.

Influence of dialysis modalities on serum AGE levels in end-stage renal disease patients

BACKGROUND

The accumulation of advanced glycation end-products (AGEs) in end-stage renal disease (ESRD) influenced by dialysis modalities is of current interest. Highly permeable membranes in haemodialysis or haemofiltration should be able to eliminate circulating AGEs as well as their AGE precursors more efficiently.

METHODS

In our study, 10 non-diabetic and 10 diabetic ESRD patients were on haemodialysis with low-flux membranes (LF) followed by a cross-over haemodialysis with high-flux or super-flux polysulfone membranes (HF, SF) for 6 months each. We measured the protein-bound pentosidine and free pentosidine serum levels by high-performance liquid chromatography (HPLC) as well as the serum AGE peptide, AGE-beta(2)-microglobulin and beta(2)-microglobulin concentrations, using ELISA assays.

RESULTS

All parameters investigated were significantly higher in dialysis patients than in healthy subjects. The reduction rates during a single dialysis session were found to be higher using the SF than those obtained with the HF (free pentosidine 82.4+/-7.3 vs 76.6+/- 8.7%; AGE peptides 79.7+/-7.7 vs 62.3+/-14.7%; AGE-beta(2)-microglobulin 64.0+/-16.5 vs 45.4+/-17.7%; beta(2)-microglobulin 70.5+/-5.6 vs 58.2+/-6.0%). The protein-bound pentosidine levels remained constant over the respective dialysis sessions. In the 6-month treatment period with the SF, decreased pre-dialysis serum levels of protein-bound pentosidine, free pentosidine and AGE peptides were observed in non-diabetics and diabetics as compared with values obtained with the LF. The respective pre-dialysis AGE-beta(2)-microglobulin concentrations decreased insignificantly, whereas those of beta(2)-microglobulin were significantly lower. Using the HF dialyser, only moderate changes of the parameters measured were noted.

CONCLUSION

Treatment with the biocompatible polysulfone SF dialyser seems to be better suited to lower serum AGE levels and to eliminate their precursors.

Phosphate removal and hemodialysis conditions

Hyperphosphatemia is frequently found in hemodialysis patients, and the association with an increased risk of mortality has been demonstrated. Other authors have linked hyperphosphatemia to increased cardiovascular mortality. The normalization of phosphate plasma levels is therefore an important goal in the treatment of end-stage renal disease patients. Absorption of phosphate from the food exceeds the elimination through a hemodialysis treatment, and this leads to a chronic phosphate load for the majority of hemodialysis patients. This imbalance should be improved by either a reduction of phosphate absorption or an increased removal of phosphate. A reduction of phosphate absorption can be achieved by reducing the amount of phosphate in the diet or by the administration of phosphate binders. Unfortunately, these measures imply practical difficulties, for example, a lack of patient compliance or other side effects. When considering modifications of the hemodialysis treatment, an essential understanding of the kinetics of dialytic phosphate removal is mandatory. Phosphate is unevenly distributed in different compartments of the body. Only a very small amount of phosphate is present in the easily accessible plasma compartment. The major part of phosphate removed during hemodialysis originates from the cytoplasm of cells. A transfer from intracellular space to the plasma and further from the plasma to the dialysate is necessary. However, if we consider improvement to phosphate removal by dialysis procedures, full dialyzer clearance is effective in only the initial phase of the dialysis treatment. After this initial phase, the transfer rate for phosphate from the intracellular space to the plasma becomes the rate-limiting step for phosphate transport. Attempts to improve this transfer rate have recently been investigated by acidosis correction, but turned out not to be consistently successful. Furthermore, modifications of the treatment schedule have been described in the literature as measures to influence the phosphate balance consistently. Successful improvements of the phosphate balance can be achieved specifically through increasing the frequency of the dialysis treatments.

Polymers in dialysis: characteristics and needs

Polymers employed in dialysis must always be evaluated from the perspective of blood compatibility. This article traces the developments that have taken place in biocompatibility and biostability in dialysis treatment and the mechanisms that are involved.