Adsorption Behavior of Polyelectrolyte onto Alumina and Application in Ciprofloxacin Removal

This study aims to investigate the adsorption behavior of a strong polyelectrolyte poly(styrenesulfonate) (PSS) onto alumina particles. Adsorption of PSS onto positively charged alumina surface increased with increasing ionic strength, indicating that non-electrostatic and electrostatic interaction controlled the adsorption. The removal of an emerging antibiotic ciprofloxacin (CFX) from water environment using PSS-modified alumina (PMA) was also studied. The removal of CFX using PMA was much higher than that using alumina particles without PSS modification in all pH ranges of 2–11. The removal of CFX reached 98% under the optimum conditions of pH 6, contact time of 120 min, adsorbent dosage of five milligrams per milliliter and ionic strength 10⁴-M NaCl. The adsorption isotherms of CFX at different salt concentrations fit well with a two-step adsorption model, while the adsorption kinetic fit well with a pseudo-second-order model with a good correlation coefficient (R² > 0.9969). The CFX-removal from a hospital wastewater using PMA was more than 75%. Our study demonstrates that adsorption of PSS onto alumina to modify the particle surface is important to form a novel adsorbent PMA for CFX-removal from water environments.

Removal of Phosphorus from Wastewater by Different Morphological Alumina

In this work, an organic-free method was used to synthesize different morphological boehmite by controlling the crystallization temperature, and alumina adsorbents were obtained by baking the boehmites at 500 °C. The alumina adsorbents were characterized by X-ray diffraction (XRD), High resolution transmission electron microscope (HRTEM), Fourier transform infrared (FT-IR), N₂ adsorption/desorption analysis, and their phosphorus adsorption properties were comparatively investigated by a series of experiments. The results showed that the self-prepared alumina adsorbents were lamellar and fibrous material, while the industrial adsorbent was a granular material. The lamellar alumina adsorbents had the largest specific surface area and showed better phosphorus adsorption capacity. The maximum adsorption capacity could reach up to 588.2 mg·g⁻¹; and only 0.8 g·L⁻¹ of lamellar alumina adsorbent is needed to treat 100 mg·L⁻¹ phosphorus solution under the Chinese level 1 discharge standard (0.5 mg·L⁻¹). Further investigation suggests that the lamellar alumina adsorbent kept high adsorption capacity in various solution environments.

Deposition of Thin Alumina Films Containing 3D Ordered Network of Nanopores on Porous Substrates

Self-supporting thin films containing nanopores are very promising materials for use for multiple applications, especially in nanofiltration. Here, we present a method for the production of nanomembranes containing a 3D ordered network of nanopores in an alumina matrix, with a diameter of about 1 nm and a body centered tetragonal structure of the network nodes. The material is produced by the magnetron sputtering deposition of a 3D ordered network of Ge nanowires in an alumina matrix, followed by a specific annealing process resulting in the evaporation of Ge. We demonstrate that the films can be easily grown on commercially available alumina substrates containing larger pores with diameters between 20 and 400 nm. We have determined the minimal film thickness needed to entirely cover the larger pores. We believe that these films have the potential for applications in the fields of filtration, separation and sensing.

Fabrication and Characterization of Sn-Based Babbitt Alloy Nanocomposite Reinforced with Al2O3 Nanoparticles/Carbon Steel Bimetallic Material

Sn-based Babbitt alloy was reinforced with alumina nanoparticles to prepare a novel class of nanocomposites. The route of liquid metallurgy in combination with stirring mechanism was chosen to prepare nanocomposites with three different loadings of alumina nanoparticles, i.e., 0.25 wt%, 0.50 wt% and 1.0 wt%. The molten mixture of metallic matrix and nanoparticles was poured over carbon steel substrate for solidification to manufacture a bimetallic material for bearing applications. The underlying aim was to understand the effect of nanoparticle addition on microstructural variation of Sn-based Babbitt alloy as well as bimetallic microstructural interface. The addition of 0.25 wt% and 0.50 wt% alumina nanoparticles significantly affected both the morphology and distribution of Cu₆Sn₅ hard phase in solid solution, which changed from needle and asterisk shape to spherical morphology. Nanocomposites containing up to 0.50 wt% nanoparticles showed more improvement in tensile strength than the one containing 1.0 wt% nanoparticles, due to nanoparticle-agglomeration and micro-cracks at the interface. The addition of 0.5 wt% nanoparticles significantly improved the wear resistance of Sn-based Babbitt alloy.

A 3D-polyphenylalanine network inside porous alumina: Synthesis and characterization of an inorganic-organic composite membrane

Surface functionalization of porous materials allows for the introduction of additional functionality coupled with high mechanical stability of functionalized inner pores. Herein, we investigate the surface-initiated ring-opening polymerization (SI-ROP) of phenylalanine-N-carboxyanhydride (PA-NCA) in porous alumina membranes (ALOX-membranes) with respect to different solvent mixtures (tetrahydrofuran (THF) and dichloromethane (DCM)). It was found that increasing the volume fraction of DCM leads to an increasing amount of fibrillar polymer structures within the porous ALOX-membrane. A three-dimensional fibrillar network with intrinsic porosity was formed in DCM, whereas in THF, a dense and smooth polypeptide film was observed. A post-treatment with a mixture of chloroform and dichloroacetic acid leads to rearrangement of the morphology of the grafted polymer films. The analysis by scanning electron microscopy (SEM), near-infrared spectroscopy (NIR) and contact angle measurements (CA) reveals a change in morphology of the grafted polymer films, which is due to the rearrangement of the secondary structure of the polypeptides. No significant loss of the surface-grafted polypeptides was determined by thermogravimetric (TG) measurements, which indicates that the change in morphology of the polymer films is solely a result of a conformational change of the surface-grafted polypeptides. Furthermore, adsorption of a test analyte (chloroanilic acid) was investigated with respect to different polymer functionalization schemes for reversed-phase solid phase extraction applications. The adsorption capability of the functionalized composite membrane was increased from 16.7% to 38.1% compared to the native ALOX-membrane.

Porous Al2O3-CNT Nanocomposite Membrane Produced by Spark Plasma Sintering with Tailored Microstructure and Properties for Water Treatment

Ceramic-based nanocomposite membranes are gaining great attention in various applications, such as water treatment; gas separation; oil and gas, amid their superior fouling resistance and remarkable chemical/thermal stability. Here, we report for the first time the use of spark plasma sintering (SPS) process to fabricate a porous alumina-carbon nanotubes (Al2O3-CNT) nanocomposite membrane for water treatment. The challenge is this work is to achieve a balance between the amount of porosity, desired for a high water flux, and the membrane strength level, required to resist the applied pressure during a water flow experiment. The effect of SPS process parameters (pressure, temperature, heating rate, and holding time) on the microstructure and properties of the developed membrane was investigated and correlated. A powder mixture composed of Al2O3 and 5 wt % CNT was prepared with the addition of starch as a pore former and gum Arabic and sodium dodecyl sulfate as dispersants. The powder mixture was then sintered using SPS to produce a solid but porous nanocomposite membrane. The structure and microstructure of the developed membrane were characterized using X-ray diffraction and field emission scanning electron microscopy. The performance of the membrane was assessed in terms of porosity, permeability, and mechanical properties. Moreover, the adsorption capability of the membrane was performed by evaluating its removal efficacy for cadmium (II) from water. The microstructural analysis revealed that CNT were distributed within the alumina matrix and located mainly along the grain boundaries. The permeability and strength were highly influenced by the sintering pressure and temperature, respectively. The results indicated that the membrane sintered at a pressure of 10 MPa, temperature of 1100 °C, holding time of 5 min, and heating rate of 200 °C/min exhibited the best combination of permeability and strength. This developed membrane showed a significant removal efficiency of 97% for cadmium (II) in an aqueous solution.

Thermal Conductivity Characterization of Thermal Grease Containing Copper Nanopowder

As electronic devices and mainboards become smaller, the need for thermal conductive materials having excellent internal heat dissipation is increasing. In this study, nano thermal grease was prepared by mixing in copper nanopowder, which is used as a heat transfer medium in thermal grease, which is a kind of thermal conductive material, with silicon oil. In addition, copper powder was mixed with graphene and alumina, respectively, and the thermal conductivity performance was compared. As a result, the thermal conductivity improved by 4.5 W/m·k over the silicon base, and the upward trend of thermal conductivity increased steadily up to 15 vol. %, and the increasing trend decreased after 20 vol. %. In addition, the increased rate of thermal conductivity from 0 to 5 vol. % and 10 to 15 vol. % was the largest.

Polydopamine-Modified Al2O3/Polyurethane Composites with Largely Improved Thermal and Mechanical Properties

Alumina/polyurethane composites were prepared via in situ polymerization and used as thermal interface materials (TIMs). The surface of alumina particles was modified using polydopamine (PDA) and then evaluated via Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TG), and Raman spectroscopy (Raman). Scanning electron microscope (SEM) images showed that PDA-Al2O3 has better dispersion in a polyurethane (PU) matrix than Al2O3. Compared with pure PU, the 30 wt% PDA-Al2O3/PU had 95% more Young's modulus, 128% more tensile strength, and 76% more elongation at break than the pure PU. Dynamic mechanical analysis (DMA) results showed that the storage modulus of the 30 wt% PDA-Al2O3/PU composite improved, and the glass transition temperature (Tg) shifted to higher temperatures. The thermal conductivity of the 30 wt% PDA-Al2O3/PU composite increased by 138%. Therefore, the results showed that the prepared PDA-coated alumina can simultaneously improve both the mechanical properties and thermal conductivity of PU.

Synthesis Based on a Preceramic Polymer and Alumina Nanoparticles via UV Lithography for High Temperature Applications

Because of the increased demand for preceramic polymers in high-tech applications, there has been growing interest in the synthesis of preceramic polymers, including polysiloxanes and alumina. These polymers are preferred because of their low thermal expansion, conformability to surfaces over large areas, and flexibility. The primary objective was to evaluate the aspects of polymer-derived ceramic routs, focusing on the UV lithography process of preceramic polymers and the pyrolyzing properties of the final ceramics. We found that the p(DMS-co-AMS) copolymer was effective in scattering the hydrophilic Al₂O₃ nanoparticles into the exceedingly hydrophobic solvent. The physico-chemical behavior of characterized copolymers was explored during their pyrolytic transformation into amorphous silicon-based ceramics. The results indicate that an increase of the pyrolysis temperature degraded the Si-O network through the carbothermic reaction of silicon. We also found a rapid elimination of copolymer pores and densification when the temperature increased (1100 to 1200 °C). At different but specific temperature ranges, there are different distinct rearrangement reactions in the conversion of polymer to ceramic; reductions of the melting point (T_m) of the total heat of melting (ΔH_m) of the pyrolysis process resulted in the crystallization of ceramic materials; hence, lithography based on pyrolysis properties of preceramic polymers is a critical method in the conversation of polymers.

An antibiotic loaded ceramic sternum to treat destroyed infected sternum: 4 cases

Background

After its destruction during refractory deep sternal wound infection (DSWI), current sternum reconstructions mainly rely on muscle flaps technique, but such technique have pitfalls and limits. To tackle the limited possibilities to use device implantation because of the risk of infection, we developed a self-protected device allowing its implantation in an infected area.

Methods

We used gentamicin alone or in combination with vancomycin loaded in a porous ceramic sternum to replace sternums destroyed during DSWI. The aim was to mechanically replace the sternum and to secure the implantation by killing the remaining bacteria in the wound thanks to the loaded antibiotic.

Results

This device was implanted in four infected patients during DWSI with sternal dehiscence. No complication occurred during surgeries, and wound healing was obtained quickly. Local antibiotic concentrations largely exceeded the ones needed for their efficacy while no antibiotic was found in the blood. All patients are well-being. However previously unknown gentamicin resistant bacteria, present in the surgical wound at the time of positioning, required sternal implant removal for one patient after 19 months. For all patients, pulmonary function tests (PFT) improved after implantation.

Conclusions

The ceramic sternum played its role consolidating the thoracic cage without stiffening. The antibiotic loaded in the sternum allowed a secure implantation, killing bacteria before the colonization of the implant even in this infected area. These four implantations are promising for patients with sternal destruction after DSWI.

Low pressure dependent elasticity of porous ceramics

The primary goal of this study was to characterize the influence of the pore-saturated gas media and their physical properties on the elasticity of porous ceramic materials. Resonant ultrasound spectroscopic measurements were performed on test specimens of alumina with ~40% porosity, zirconia with ~48% porosity, and sintered fully dense zirconia to determine the hydrostatic pressure-dependent macroscopic elasticity. Here, we report the variation of elasticity of porous and full dense samples over approximately five orders of magnitude (800-0.02 psi) in absolute pressure. The time evolution of mechanical equilibrium of the porous materials at low pressure and high-temperature conditions will also be discussed.

Gas Permeation Property of Silicon Carbide Membranes Synthesized by Counter-Diffusion Chemical Vapor Deposition

An amorphous silicon carbide (SiC) membrane was synthesized by counter-diffusion chemical vapor deposition (CDCVD) using silacyclobutane (SCB) at 788 K. The SiC membrane on a Ni-γ-alumina (Al₂O₃) α-coated Al₂O₃ porous support possessed a H₂ permeance of 1.2 × 10⁻⁷ mol·m⁻²·s⁻¹·Pa⁻¹ and an excellent H₂/CO₂ selectivity of 2600 at 673 K. The intermittent action of H₂ reaction gas supply and vacuum inside porous support was very effective to supply source gas inside mesoporous intermediate layer. A SiC active layer was formed inside the Ni-γ-Al₂O₃ intermediate layer. The thermal expansion coefficient mismatch between the SiC active layer and Ni-γ-Al₂O₃-coated α-Al₂O₃ porous support was eased by the low decomposition temperature of the SiC source and the membrane structure.

Joining Alumina and Sapphire by Growing Aluminium Borate Whiskers In-Situ, and the Whiskers' Orientation Relationship with the Sapphire Substrate

Bonding between polycrystal alumina and sapphire with (0001), (10 1¯0), (11 2¯0), (1 1¯02) orientations is successfully achieved by growing aluminium borate whiskers in the joint. The morphology of the whiskers in the joint is characterised by (Scanning Electron Microscopy) SEM. The relationship between the growing direction of the aluminium borate whiskers and the orientation of the sapphire substrate is investigated. The effect of the growing direction of the aluminium borate whiskers on the mechanical properties of the joint is discussed. The results show that the whiskers on the sapphire with (10 1¯0) orientation grow perpendicular to the surface of the substrate while the whiskers show a random growth on the other substrates. It is found that there is an orientation relationship between the whiskers (220) and sapphire (10 1¯0) and the morphology of the whiskers has great influence on the mechanical properties of the joint. The joint between polycrystal alumina and sapphire with (10 1¯0) orientation exhibits the highest strength, which reaches 26 MPa.

Hardness and Indentation Fracture Toughness of Slip Cast Alumina and Alumina-Zirconia Ceramics

Alumina (Al₂O₃) and zirconia (ZrO₂) have good overall properties and thus are widely used oxide technical ceramics. The biggest drawback of Al₂O₃ is its low fracture toughness. In contrast, ZrO₂ is relatively tough, but is also much more expensive. In order to improve the alumina toughness, composite ceramics are being developed. Slip casting technology has economic advantages over the conventional hot isostatic pressure technology, but problems may arise when preparing stable highly-concentrated suspensions (slip) for filling the mold. The purpose of this study is to prepare aqueous suspensions using 70 wt. % α-Al₂O₃, with 0, 1, 5 and 10 wt. % of added t-ZrO₂. Suspensions were electrosterically stabilized using the ammonium salt of polymethylacrylic acid, an alkali-free anionic polyelectrolyte dispersant. Also, magnesium oxide in form of magnesium aluminate spinel (MgAl₂O₄) was used to inhibit the abnormal alumina grain growth during the sintering process. Minimum viscosities were used as stability estimators, where an increase in ZrO₂ content required adding more dispersant. After sintering, the Vickers indentation test was used to determine the hardness and the indentation fracture toughness from the measurement of the crack length. Also, the brittleness index (B_i, μm^−1/2) was calculated from values of Vickers hardness and the Vickers indentation fracture toughness. It was found that with increasing ZrO₂ content the fracture toughness increased, while the hardness as well as the brittleness index decreased. Zirconia loading reduces the crystallite sizes of alumina, as confirmed by the X-ray diffraction analysis. SEM/EDS analysis showed that ZrO₂ grains are distributed in the Al₂O₃ matrix, forming some agglomerates of ZrO₂ and some pores, with ZrO₂ having a smaller grain size than Al₂O₃.

The Role of Humic Acid, PP Beads, and pH with Water Backwashing in a Hybrid Water Treatment of Multichannel Alumina Microfiltration and PP Beads

Photooxidation oxidizes most organic compounds by mineralizing them to small inorganic molecules. In this study, the effects of dissolved organic matter (DOM), pH, and polypropylene (PP) beads concentration on membrane fouling were investigated in a hybrid water treatment process consisting of seven-channel alumina microfiltration (pore size 1.0 μm) and pure PP beads water backwashing with UV irradiation for photooxidation. The synthetic feed was prepared with humic acid and kaolin and flowed inside the microfiltration (MF) membrane. The permeate contacted the PP beads fluidized in the gap of the membrane and module with outside UV irradiation. Membrane fouling resistance (R_f) increased dramatically with an increase in the concentration of humic acid (HA) from 6 mg/L to 8 mg/L. The treatment efficiency of DOM increased dramatically, from 14.3% to 49.7%, with an increase in the concentration of HA. The R_f decreased with an increase of PP beads concentration. However, maximum permeate volume (V_T) was acquired at 5 g/L of PP beads. The maximal treatment efficiency of DOM was 51.3% at 40 g/L of PP beads. The R_f increased with an increase in the pH of feed, and the maximum V_T was acquired at a pH of 5. The maximal treatment efficiency of DOM was 52.5% at pH 9.

Obtaining Alumina from Kaolin Clay via Aluminum Chloride

A method of alumina production based on hydrochloric acid processing of kaolin clays from the East Siberian deposits was studied. Hydrochloric acid leaching was carried out at 160 °C. The leaching solution was subjected to a two-stage crystallization of aluminum chloride hexahydrate (ACH). The precipitated crystals were calcinated in air at a temperature above 800 °C to produce alumina. The main part of water and chlorine during thermal decomposition of ACH was removed at 400 °C. The influence of temperature and duration of ACH calcination on the residual chlorine content in alumina was studied. The optimal temperature of ACH calcination was 900 °C with a duration of 90 min. It was shown that the increase in calcination temperature contributed to the decrease in chlorine content in the final product. However, an increase in calcination temperature above 900 °C led to the transition of the well-soluble γ-Al₂O₃ phase to the insoluble α-Al₂O₃, which negatively affected the further electrolysis of aluminum. The size of alumina particles was not affected by the calcination mode. The rate of dissolution of the prototype Al₂O₃ in Na₃AlF₆ was higher than for the alumina obtained by the classical method. Alumina content, particle morphology, and particle size distribution for the obtained alumina were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), and laser diffraction methods. The obtained alumina is suitable for aluminum production according to the studied characteristics.

Cotton Candy-Templated Fabrication of Three-Dimensional Ceramic Pathway within Polymer Composite for Enhanced Thermal Conductivity

With the minimization and higher power of electronic devices, materials with effective heat dissipation and high electrical insulation have attracted relentless interest. Especially, highly thermally conductive, highly electrically insulating but low filler content of polymer-based composites are desirable. Herein, a facile and eco-friendly cotton candy-templated method (CTM) to construct three-dimensional heat transport pathways inside epoxy resin is reported. The fabricated Al₂O₃/epoxy composites with enhanced heat transport capability feature a 15-fold increase in thermal conductivity at a filler content of 36.2 vol % compared to pristine epoxy. Moreover, the remarkable thermal conductive property has excellent stability over a wide range of temperature before and after heating and cooling cycles. Meanwhile, the CTM composite still retain highly electrical insulation. The cotton candy-templated method proposed in this work is a new avenue for the preparation of three-dimensional heat transport pathways within polymer-based composites for microelectronic packaging and electrical engineering systems.

Recent Advances and Future Prospects in Spark Plasma Sintered Alumina Hybrid Nanocomposites

Although ceramics have many advantages when compared to metals in specific applications, they could be more widely applied if their low properties (fracture toughness, strength, and electrical and thermal conductivities) are improved. Reinforcing ceramics by two nano-phases that have different morphologies and/or properties, called the hybrid microstructure design, has been implemented to develop hybrid ceramic nanocomposites with tailored nanostructures, improved mechanical properties, and enhanced functionalities. The use of the novel spark plasma sintering (SPS) process allowed for the sintering of hybrid ceramic nanocomposite materials to maintain high relative density while also preserving the small grain size of the matrix. As a result, hybrid nanocomposite materials that have better mechanical and functional properties than those of either conventional composites or nanocomposites were produced. The development of hybrid ceramic nanocomposites is in its early stage and it is expected to continue attracting the interest of the scientific community. In the present paper, the progress made in the development of alumina hybrid nanocomposites, using spark plasma sintering, and their properties are reviewed. In addition, the current challenges and potential applications are highlighted. Finally, future prospects for developing alumina hybrid nanocomposites that have better performance are set.

The potential of additive manufacturing technologies and their processing parameters for the fabrication of all-ceramic crowns: A review

OBJECTIVE

This article aims to provide a review of the additive manufacturing technologies and the processing parameters that have been investigated for the fabrication of all ceramic crowns.

OVERVIEW

Additive manufacturing has crept its way into the field of dentistry for the fabrication of resin and metal prosthesis. To evaluate the current status of additive manufacturing for the fabrication of all ceramic crowns, literature review was targeted to include publications pertaining to the fabrication of dental ceramics and all ceramic crowns. With respect to the additive manufacturing of dental ceramics, five technologies have been investigated to date: stereolithography, material extrusion, powder based fusion, direct inkjet printing, and binder jetting. The processing parameters and experimental outcomes were collated and described for each of the aforementioned technologies.

CONCLUSION

Additive manufacturing has demonstrated promising experimental outcomes and corroborated to the fabrication all ceramic crowns. However, the technology is yet to witness a commercial breakthrough within this domain.

CLINICAL SIGNIFICANCE

Additive manufacturing mitigates raw material wastage and tooling stresses that are associated with milling of ceramics. Continued research and development can lead to its approbation as an alternate technology for manufacturing all ceramic restorations.

Aluminum-Alumina Composites: Part Ⅰ: Obtaining and Characterization of Powders

The process of advanced aluminum-alumina powders production for selective laser melting was studied. The economically effective method of obtaining aluminum-alumina powdery composites for further selective laser melting was comprehensively studied. The aluminum powders with 10-20 wt. % alumina content were obtained by oxidation of aluminum in water. Aluminum oxidation was carried out at ≤200 °C. The oxidized powders were further dried at 120 °C and calcined at 600 °C. Four oxidation modes with different process temperatures (120-200 °C) and pressures (0.15-1.80 MPa) were investigated. Parameters of aluminum powders oxidation to obtain composites with 10.0, 14.5, 17.4, and 20.0 wt. % alumina have been determined. The alumina content, particle morphology, and particle size distribution for the obtained aluminum-alumina powdery composites were studied by XRD, SEM, laser diffraction, and volumetric methods. According to the obtained characteristics of aluminum-alumina powdery composites, they are suitable for the SLM process.

Boron Removal from Aqueous Solutions by Using a Novel Alginate-Based Sorbent: Comparison with Al2O3 Particles

Boron removal was evaluated in the present work by using calcium alginate beads (CA) and a novel composite based on alginate–alumina (CAAl) as sorbents in a batch system. The effects of different parameters such as pH, temperature, contact time, and composition of alginate (at different concentrations of guluronic and mannuronic acids) on boron sorption were investigated. The results confirm that calcium alginate beads (CA) exhibited a better adsorption capacity in a slightly basic medium, and the composite alginate–alumina (CAAl) exhibited improved boron removal at neutral pH. Sorption isotherm studies were performed and the Langmuir isotherm model was found to fit the experimental data. The maximum sorption capacities were 4.5 mmol g⁻¹ and 5.2 mmol g⁻¹, using CA and CAAl, respectively. Thermodynamic parameters such as change in free energy (ΔG⁰), enthalpy (ΔH⁰), and entropy (ΔS⁰) were also determined. The pseudo-first-order and pseudo-second-order rate equations (PFORE and PSORE, respectively) were tested to fit the kinetic data; the experimental results can be better described with PSORE. The regeneration of the loaded sorbents was demonstrated by using dilute HCl solution (distilled water at pH 3) as eluent for metal recovery.

Expanded Porphyrin Contraction: From [22]Triphyrin(6.6.0) to [22]Triphyrin(6.5.0)

An expanded triphyrin containing a bipyrrole moiety and annulene links, namely tetraphenyl-[22]triphyrin(6.5.0), 2, has been synthesized. The synthesis proceeded by a postsynthetic transformation of tetraphenyl-[22]triphyrin(6.6.0), 1, in a metal-free unexpected and unprecedented ring contraction during column chromatography on alumina. The observed transformation, located at the hydrocarbon chain linking the pyrrole units, formally corresponds to a subtraction of one carbon atom from an annulene circuit. In contrast to the flexible substrate 1, the product 2 is conformationally rigid, and capable of chloride anion binding in its protonated form.

Microwave Sintering of Alumina at 915 MHz: Modeling, Process Control, and Microstructure Distribution

Microwave energy can be advantageously used for materials processing as it provides high heating rates and homogeneous temperature field distribution. These features are partly due to the large microwave penetration depth into dielectric materials which is, at room temperature, a few centimeters in most dielectric materials. However, up to now, this technology is not widely spread for high-temperature material processing applications (>1200 °C), because its reproducibly and ability to sinter large size samples (>30 cm³) still needs to be improved. In this context, this paper describes both an empirically designed 915 MHz single-mode cavity made from SiC susceptors and refractory thermal insulation, and the 3D modeling of the process in order to improve our understanding of it. Different susceptors geometries and coupling slit position were numerically tested in order to better understand how these parameters impact the field homogeneity and the process stability. It was found that positioning the largest surface of the susceptors parallel to the electrical field allows a very uniform and hybrid heating of the material, while avoiding plasma or thermal instabilities. This was correlated to the 3D modeling results. Finally, thanks to a fully-automatized system this apparatus was used to sinter large size (~30 cm³) low-loss dielectric alumina samples. The sintered materials were subsequently characterized in terms of density, grain size distribution, and homogeneity. The reproducibility was also discussed, demonstrating the process efficiency and reliability.

Alumina Coated Silica Nanosprings (NS) Support Based Cobalt Catalysts for Liquid Hydrocarbon Fuel Production From Syngas

The effects of Al₂O₃ coating on the performance of silica nanospring (NS) supported Co catalysts for Fischer–Tropsch synthesis (FTS) were evaluated in a quartz fixed-bed microreactor. The Co/NS-Al₂O₃ catalysts were synthesized by coating the Co/NS and NS with Al₂O₃ by an alkoxide-based sol-gel method (NS-Al-A and NS-Al-B, respectively) and then by decorating them with Co. Co deposition was via an impregnation method. Catalysts were characterized before the FTS reaction by the Brunauer–Emmett–Teller (BET) method, X-ray diffraction, transmission electron microscopy, temperature programmed reduction, X-ray photoelectron spectroscopy, differential thermal analysis and thermogravimetric analysis in order to find correlations between physico-chemical properties of catalysts and catalytic performance. The products of the FTS were trapped and analyzed by GC-TCD and GC-MS to determine the CO conversion and reaction selectivity. The Al₂O₃ coated NS catalyst had a significant affect in FTS activity and selectivity in both Co/NS-Al₂O₃ catalysts. A high CO conversion (82.4%) and Σ > C₆ (86.3%) yield were obtained on the Co/NS-Al-B catalyst, whereas the CO conversion was 62.8% and Σ > C₆ was 58.5% on the Co/NS-Al-A catalyst under the same FTS experimental condition. The Co/NS-Al-A catalyst yielded the aromatic selectivity of 10.2% and oxygenated compounds.

Pulse Duration and Wavelength Effects of Laser Ablation on the Oxidation, Hydrolysis, and Aging of Aluminum Nanoparticles in Water

We analyzed the formation of the aluminum (Al) nanoparticles (NPs) with triangular shape obtained by ablating Al bulk in liquid using pulses with different durations (5 ns, 200 ps, and 30 fs) and wavelengths (355 nm, 800 nm, and 1064 nm). We report three stages of synthesis and aging of Al NPs: Formation, transformation, and stable stage. The NPs prepared by different pulses are almost identical at the initial stage. The effects of duration and wavelength of the ablation pulses on the aging of NPs are revealed. Pulse duration is determined to be essential for morphological transformation of NPs, while pulse wavelength strongly influences particle sizes. NPs produced by ultra-short pulses have smaller sizes and narrow size distribution. We demonstrate that oxidation and hydrolysis of Al in water are the results of ablation for all pulse durations and wavelengths, which also strongly modify the preferable reaction path of NPs in water, thus affecting the composition and morphology of triangle NPs. The results of modeling of the NPs generation in water due to a 50 ps laser pulse interacting with a thick Al target are presented. Water-based effects in the formation of NPs, their evolution, and solidification are considered from the mechanical and thermophysical points of view. The detailed analysis of the modeling results allowed for determination of the main mechanism responsible for the ablation process followed by the NPs formation.