Hierarchical bi-continuous Pt decorated nanoporous Au-Sn alloy on carbon fiber paper for ascorbic acid, dopamine and uric acid simultaneous sensing

Electrochemical and quantum chemical approaches to the study of dopamine sensing using bentonite and l-cysteine modified carbon paste electrode

This work presents a significant investigation involving both electrochemical experiment and quantum chemical simulation approaches. The objective was to characterize the electrochemical detection of dopamine (DA). The detection was carried out using a modified carbon paste electrode (CPE) incorporating bentonite (Bent) and l-cysteine (CySH) (named as CySH/Bent/CPE). To understand and explain the oxidation mechanism of DA on the CySH/Bent modified electrode surface, the coupling of the two approaches were exploited. The CySH/Bent/CPE showed excellent electroactivity toward DA such as good sensibility, selectivity, stability, and regenerative ability. The developed sensor shows a dynamic linear range from 0.8 to 80 μM with a limit of detection and quantification of 0.5 μM and 1.5 μM, respectively. During the quantitative analysis of DA in presence of ascorbic acid (AA) and uric acid (UA) the electrochemical oxidation signals of AA, DA, and UA distinctly appear as three separate peaks. The potential differences between the peaks are 190 mv, 150 mv, and 340 mV for the AA-DA, DA-UA, and AA-UA oxidation pairs, respectively. These observations stem from square wave voltammetry (SWV) studies, along with the corresponding redox peak potential separations. The developed sensor is simple and accurate to monitor DA in human serum samples. On the other hand, CySH acts as an electrocatalyst on the CySH/Bent/CPE surface by increasing its active electron transfer sites, as suggested by the quantum chemical modeling with analytical results of Fukui. Furthermore, the voltammetric results obtained agree well with the theoretical calculations.

Highly sensitive and simultaneous detection of ascorbic acid, dopamine, and uric acid using Pt@g-C3N4/N-CNTs nanocomposites

The detection of ascorbic acid (AA), dopamine (DA), and uric acid (UA) is crucial for understanding and managing various illnesses. In this research, Pt@g-C3N4 nanoparticles were synthesized via hydrothermal method and combined with N-doped carbon nanotubes (N-CNTs). The Pt@g-C3N4/N-CNTs-modified glassy carbon (GC) electrode was fabricated as an electrochemical sensor for the determination of AA, DA, and UA. The linear response range of AA, DA, and UA in the optimal condition was 100-3,000 μM, 1-100 μM, and 2-215 μM boasting a low detection limit (S/N = 3) of 29.44 μM (AA), 0.21 μM (UA), and 2.99 μM (DA), respectively. Additionally, the recoveries of AA, DA, and UA in serum sample were 100.4%-106.7%. These results corroborate the feasibility of the proposed method for the simultaneous, sensitive, and reliable detection of AA, DA, and UA. Our Pt@g-C3N4/N-CNTs/GC electrode can provide a potential strategy for disease diagnosis and health monitoring in clinical settings.

Insights into electrogenerated intermediates and rapid screening of electrochemical reactions by surface-modified carbon fiber paper redox spray ionization mass spectrometry

The combination of electrochemistry and mass spectrometry is a powerful analytical tool for studying redox reaction mechanisms and identifying products or intermediates. However, the previously reported devices all require bespoke fabrication and are too complicated to be assembled and used by others. Crucially, the long ion transport distance and small spray volumes make it difficult to capture the short-lived intermediates. We present a practical mass spectrometric method in which surface-modified carbon fiber paper is innovatively applied to detect electrogenerated intermediates. Treating carbon fiber paper with dilute nitric acid removes its surface impurities, enhancing the capability of electro-redox. Electrospray ionization and redox reaction occur simultaneously on the tip of the paper. Transient electro-redox species generate and transfer into gas phase as soon as the appearance of spray. Rapid transport of quantities of electrogenerated ions to the mass spectrometer inlet makes it possible for mass spectrometric identification on the millisecond scale. The short-lived radical cations and iminium ions were successfully captured, reflecting the starting step of the cross-dehydrogenation coupling reaction. The real-time oxidation and online functionalization reactions of tertiary amines were achieved using this device without additional oxidants and electrolytes. In this way we could achieve in-depth mechanistic understanding and rapid screening of serial reactions.

Progress in optical sensors-based uric acid detection

The escalating number of patients affected by various diseases, such as gout, attributed to abnormal uric acid (UA) concentrations in body fluids, has underscored the need for rapid, efficient, highly sensitive, and stable UA detection methods and sensors. Optical sensors have garnered significant attention due to their simplicity, cost-effectiveness, and resistance to electromagnetic interference. Notably, research efforts have been directed towards UA on-site detection, enabling daily monitoring at home and facilitating rapid disease screening in the community. This review aims to systematically categorize and provide detailed descriptions of the notable achievements and emerging technologies in UA optical sensors over the past five years. The review highlights the advantages of each sensor while also identifying their limitations in on-site applications. Furthermore, recent progress in instrumentation and the application of UA on-site detection in body fluids is discussed, along with the existing challenges and prospects for future development. The review serves as an informative resource, offering technical insights and promising directions for future research in the design and application of on-site optical sensors for UA detection.

Enzymatic and Non-Enzymatic Uric Acid Electrochemical Biosensors: A Review

In recent years, the development of electrochemical biosensors for uric acid has made great achievements. Firstly, uric acid electrochemical biosensors were classified according to their reaction mechanism. Then, the reaction mechanism of the uric acid sensor and the application of nano-modified materials were deeply analyzed from the perspective of non-enzyme and enzymes. In this paper, the catalytic oxidation capacity, enzyme adsorption effect, conductivity, robustness, detection range, and detection limit of uric acid sensors were discussed and compared. Finally, the advantages of acid-sensitive electrochemical biosensors were summarized, and the constructive recommendations were proposed for improving the deficiencies of acid biosensors. The potential for further development in this area was also discussed.

Dual-mode biosensor platform based on synergistic effects of dual-functional hybrid nanomaterials

Detection of biomarkers is very vital in the prevention, diagnosis and treatment of diseases. However, due to the poor accuracy and sensitivity of the constructed biosensors, we are now facing great challenges. In addressing these problems, nanohybrid-based dual mode biosensors including optical-optical, optical-electrochemical and electrochemical-electrochemical have been developed to detect various biomarkers. Integrating the merits of nanomaterials with abundant active sites, synergy and excellent physicochemical properties, many bi-functional nanohybrids have been reasonable designed and controllable preparation, which applied to the construction dual mode biosensors. Despite the significant progress, further efforts are still needed to develop dual mode biosensors and ensure their practical application by using portable digital devices. Therefore, the present review summarizes an in-depth evaluation of the bi-functional nanohybrids assisted dual mode biosensing platform of biomarkers. We are hoping this review could inspire further concepts in developing novel dual mode biosensors for possible detection application.

Rh single-atom nanozymes for efficient ascorbic acid oxidation and detection

The management of ascorbic acid (AA) in biological fluids is of significant importance for body functions and human health, yet challenging due to the lack of high-performance sensing catalysts. Herein, we report the design of Rh single-atom nanozymes (Rh SAzymes) by mimicking the active sites of ascorbate peroxidase toward efficient electrocatalytic oxidation and detection of AA. Benefiting from the enzyme-mimicking single-atom coordination, the Rh SAzyme exhibits an unprecedented electrocatalytic activity for AA oxidation with an onset potential as low as 0.02 V (vs. Ag/AgCl). Combined with the screen-printing technology, a miniaturized Rh SAzyme biosensor was firstly constructed for tracking dynamic trends of AA in the human subject and detecting AA content in nutritional products. The as-prepared biosensor exhibits excellent detection performances with a wide linear range of 10.0 μM-53.1 mM, a low detection limit of 0.26 μM, and a long stability of 28 days. This work opens a door for the design of artificial single-atom electrocatalysts to mimic natural enzymes and their subsequent application in biosensors.

Enzyme-free and wide-range portable colorimetric sensing system for uric acid and hydrogen peroxide based on copper nanoparticles

Uric acid (UA) is the final product of purine metabolism. A high concentration of UA in body fluid may lead to kidney stones, gout, and some cardiovascular diseases. Therefore, the non-invasive daily monitoring of UA is of great significance for both hyperuricemia patients and fit people. However, most of the current detection methods for UA are enzyme-dependent which limits the application scenarios and lacks portable instruments for on-site detection, including optics and electrochemistry. In this work, an enzyme-free and wide-range colorimetric sensor for UA and H₂O₂ detection was developed based on a mercaptosuccinic acid (MSA)-modified Cu nanoparticles (CuNPs). Under the action of UA or H₂O₂, with the cleavage of MSAs on the CuNPs surface, small Cu particles are further aggregated into larger particles with a lightning violet color. With the employment of the multi-channel handheld automatic photometer (MHAP), the concentration of UA and H₂O₂ can be determined on-site according to the absorbance measurement by the photodiodes. The linear range of UA was 5 μM-4.5 mM with the limit of detection (LOD) of 3.7 μM, while the linear range of H₂O₂ was 5 mM-500 mM and 5 μM-5 mM with the LOD of 4.3 μM. This approach has been applied to the detection of UA in human urine, providing more possibilities for non-invasive home health monitoring, community medical diagnosis, and broader prospects of on-site disease detection.

A flexible and sensitive electrochemical sensing platform based on dimethyl sulfoxide modified carbon cloth: towards the detection of dopamine and carvedilol

The determination of neurotransmitters and adrenoreceptor drugs is highly essential due to their specific functions in the human body. In this work, the determination of carvedilol (CAR) and dopamine (DA) was carried out using carbon cloth (CC), which was modified using a facile strategy of drop-casting dimethyl sulfoxide (DMSO). This induced the formation of functional groups without any loss in the structural integrity of CC. The DMSO modified CC (CC-DMSO) was used for the detection of CAR in the range of 1 nM to 10 μM with a limit of detection (LOD) of 120 pM. Similarly, the CC-DMSO was able to detect DA in the range of 10 pM to 10 μM with a highly promising LOD of 0.3 pM. A bending test was also carried out on the electrode and it could be seen that only a negligible variation in sensing capability was observed when the electrode was in the bent form. In addition, the detection of CAR and DA was also carried out in real samples such as human serum. This study reveals that this modification strategy can serve as a versatile and flexible sensing platform for the detection of CAR and DA together in real world medical scenarios.

Simultaneous detection of dihydroxybenzene isomers in the environment by a free-standing flexible ZnCo2O4 nanoplate arrays/carbon fiber cloth electrode

The simultaneous determination of dihydroxybenzene isomers is highly valuable for early environmental monitoring, but it is still a challenge. In this work, a free-standing flexible electrode was prepared for the simultaneous detection of hydroquinone (HQ), catechol (CC), and resorcinol (RC). The bimetallic zinc/cobalt zeolitic imidazolate frameworks nanoplate arrays (Zn/Co-ZIF NPAs) grown in situ on the carbon fiber cloth (CFC) was fabricated by a facile static synthesis method, and the porous ternary ZnCo₂O₄ NPAs derived from Zn/Co-ZIF NPAs were formed by annealing in air. Due to the fast electron transmission, abundant active sites and excellent electrocatalytic properties with enzyme-like kinetic performance of the ZnCo₂O₄/CFC electrode, the as-proposed sensor showed a wilder linear response (2-500 μM), a lower detection limits (0.03 μM HQ, 0.06 μM CC and 0.15 μM RC) and a higher sensitivity (23.58 μA μM^-1 cm^-2 HQ, 17.72 μA μM^-1 cm^-2 CC, and 15.18 μA μM^-1 cm^-2 RC), respectively. More importantly, the proposed electrochemical sensor exhibited excellent detection performance in complex water samples, providing a strategy for the detection of other toxic substances in the ecological environment.

Activated Glassy Carbon Electrode as an Electrochemical Sensing Platform for the Determination of 4-Nitrophenol and Dopamine in Real Samples

Glassy carbon electrode (GCE) was electrochemically activated using a repetitive cyclic voltammetric technique to develop an activated glassy carbon electrode (AGCE). The developed AGCE was optimized and utilized for the electrochemical assay of 4-nitrophenol (4-NP) and dopamine (DA). Cyclic voltammetry (CV) was employed to investigate the electrochemical behavior of the AGCE. Compared to the bare GCE, the developed AGCE exhibits a significant increase in redox peak currents of 4-NP and DA, which indicates that the AGCE significantly improves the electrocatalytic reduction of 4-NP and oxidation of DA. The electrochemical signature of the activation process could be directly associated with the formation of oxygen-containing surface functional groups (OxSFGs), which are the main reason for the improved electron transfer ability and the enhancement of the electrocatalytic activity of the AGCE. The effects of various parameters on the voltammetric responses of the AGCE toward 4-NP and DA were studied and optimized, including the pH, scan rate, and accumulation time. Differential pulse voltammetry (DPV) was also utilized to investigate the analytical performance of the AGCE sensing platform. The optimized AGCE exhibited linear responses over the concentration ranges of 0.04-65 μM and 65-370 μM toward 4-NP with a lower limit of detection (LOD) of 0.02 μM (S/N = 3). Additionally, the AGCE exhibited a linear responses over the concentration ranges of 0.02-1.0 and 1.0-100 μM toward DA with a lower limit of detection (LOD) of 0.01 μM (S/N = 3). Moreover, the developed AGCE-based 4-NP and DA sensors are distinguished by their high sensitivity, excellent selectivity, and repeatability. The developed sensors were successfully applied for the determination of 4-NP and DA in real samples with satisfactory recovery results.

An Enzyme-Free Photoelectrochemical Sensor Platform for Ascorbic Acid Detection in Human Urine

A novel enzyme-free photoelectrochemical (PEC) potential measurement system based on Dy-OSCN was designed for ascorbic acid (AA) detection. The separation and transmission of internal carriers were accelerated and the chemical properties became more stable under light excitation due to the regular microstructure of the prepared Dy-OSCN monocrystal. More importantly, the PEC potential method (OCPT, open circuit potential-time) used in this work was conducive to the reduction of photoelectric corrosion and less interference introduced during the detection process, which effectively ensured the repeatability and stability of the electrode. Under optimal conditions, the monocrystal successfully served as a matrix for the detection of AA, and the prepared PEC sensor exhibited a wide linear range from 7.94 × 10−6 mol/L to 1.113 × 10−2 mol/L and a sensitive detection limit of 3.35 μM. Practical human urine sample analysis further revealed the accuracy and feasibility of the Dy-OSCN-based PEC platform. It is expected that such a PEC sensor would provide a new way for rapid and non-invasive AA level assessment in human body constitution monitoring and lays a foundation for the further development of practical products.

A bio-analytic nanoplatform based on Au post-functionalized CeFeO3 for the simultaneous determination of melatonin and ascorbic acid through photo-assisted electrochemical technology

Both melatonin and ascorbic acid could perform an irreplaceable role in maintaining the ecological balance of the human body and fighting cardiovascular diseases. Herein, a dual-channel photo-assisted electrochemical sensor has been fabricated based on Au post-functionalized CeFeO₃ nanospheres to simultaneously monitor melatonin and ascorbic acid for the first time. Briefly, CeFeO₃ nanospheres are prepared through a hydrothermal and annealing process, and then the reduced Au nanoclusters are anchored on the surface of spheres to afford the CeFeO₃@Au bi-nanospherical sensing probe. Impressively, the pre-fabricated sensor can produce a current signal 11% higher under light than that produced in a dark environment during the electrochemical measurements. Subsequently, the sensor fabricated by our strategy has achieved the simultaneous determination of melatonin and ascorbic acid with the wide detecting ranges of 1 nM-5 μM and 1 nM to 2 μM, and low detection limits of 0.8 nM and 0.4 nM by electrochemical measurements with the presence of the sunlight, and has shown satisfactory recoveries in the real sample measurements, demonstrating that the CeFeO₃@Au bi-nanospherical sensing probe will be an auspicious candidate of advanced electrode material in photo-assisted electrochemical sensing applications.

An electrochemical sensor for sensitive detection of dopamine based on a COF/Pt/MWCNT-COOH nanocomposite

Herein, an electrochemical sensor was developed for sensitive detection of dopamine (DA) based on a novel COF-based nanocomposite named COF/Pt/MWCNT-COOH, which possesses large specific surface area, excellent electrical conductivity, and high catalytic activity, thus broadening the application of COFs in the electrochemical sensing area.

Integrated electrochemical microfluidic sensor with hierarchically porous nanoarrays modified graphene fiber microelectrode for bioassay

The development of high-efficient biosensing systems for rapid and sensitive detection of disease-related biomarkers in human samples is of great significance for disease diagnosis and treatment in clinical practice. In this work, we develop an integrated electrochemical microfluidic sensing platform based on freestanding graphene fiber (GF) microelectrode for bioassay. In order to improve the electrocatalytic activity of GF microelectrode, it has been modified by unique 3D well-ordered hierarchically porous nickel-cobalt phosphide (NiCoP) nanosheet arrays (NSAs). Benefiting from the excellent electrochemical properties and structural merits, the resultant NiCoP-NSAs modified GF microelectrode shows excellent sensing performances towards neurotransmitter dopamine (DA), with a high sensitivity of 5.56 μA cm^-2 μM^-1, a low detection limit of 14 nM, as well as good selectivity, reproducibility and stability. Furthermore, in virtue of the miniaturized size and good mechanical properties, the nanohybrid GF microelectrode can be embedded into a home-made microfluidic chip to construct an integrated electrochemical microfluidic sensing device, which has been used for sensitive analysis of DA in minimal volume of human serum and urine samples, and in situ tracking DA released from neuroblastoma cells SHSY-5Y under the stimulation for physio-pathological and pharmacological study of nervous system-related diseases.

Controlled synthesis of Cu-Sn alloy nanosheet arrays on carbon fiber paper for self-supported nonenzymatic glucose sensing

Nanoalloy shows significant advantages and broad application prospects in chemical catalysis, due to the possessed high specific surface energy and abundant active sites can greatly promote their catalytic performance. In this work, morphology-controlled Cu-Sn alloy nanosheet arrays supported on carbon fiber paper (CP) substrate (Cu-Sn/CP) have been developed by a facile one-step electrodeposition technique at room temperature for the first time. Benefiting from the large active surface area, considerable ion transport channels and strong synergistic catalytic effect between Cu and Sn, the as-prepared Cu-Sn/CP served as a self-supported electrode for efficient nonenzymatic glucose sensing. Under optimized conditions, Cu-Sn/CP electrode offers wide linear ranges of 0.0005-2.0 mM and 2.0-10.0 mM, respectively. The detection limit is as low as 0.061 μM (S/N = 3). Cu-Sn/CP electrode also exhibited excellent selectivity and stability. Additionally, the proposed sensor is proven to be suitable for the detection of glucose in human serum samples.

Superhydrophilic edge-rich graphene for the simultaneous and disposable sensing of dopamine, ascorbic acid, and uric acid

A simple and rapid simultaneous sensing strategy of multiple biomarkers is of great importance but challenging in health diagnosis. In this study, a novel free-standing edge-rich graphene film (fs-ERG) was...

Electrochemical dopamine sensor based on bi-metallic Co/Zn porphyrin metal-organic framework

Integrating other metal ions into mono-metallic metal-organic framework (MOF) to form bi-metallic MOF is an effective strategy to enhance the performance of MOFs from the internal structure. In this study, two-dimensional (2D) cobalt/zinc-porphyrin (Co/Zn-TCPP) MOF nanomaterials with different Co/Zn molar ratios were synthesised using a simple surfactant-assisted method, and novel dopamine (DA) sensing methods were constructed based on these materials. The characterisation results showed that all MOF with different Co/Zn molar ratios presented a nanofilm, and the Co and Zn elements were uniformly distributed. All sensors based on Co_xZn_100-x-TCPP had a certain catalytic performance to DA. Among them, the sensor based on CO₂₅Zn₇₅-TCPP showed the strongest signal response, indicating that the catalytic performance of MOF on DA can be adjusted by changing the Co/Zn molar ratio. The doping of metal ions improves the chemical environment of the pores, and increases the types and spatial arrangement of the active sites of the MOF, which is beneficial to the electron transfer and exchange with DA; Co²⁺ and Zn²⁺ active centres have a synergistic promotion effect, so the catalytic activity of MOF is significantly improved. The linear range at the potential of 0.1 V based on Co₂₅Zn₇₅-TCPP for DA was 5 nM-177.8 μM, with a detection limit of 1.67 nM (S/N = 3). The sensor exhibited a good selectivity for detecting DA. This research is expected to provide new ideas and references for constructing high-performance sensing interfaces and platforms.

A novel 3D coordination polymer constructed by dual-ligand for highly sensitive detection of purine metabolite uric acid

Uric acid (UA), as the final product of purine metabolism, exists in urine and serum, which plays an important role in human metabolism, immunity and other functions. The sensitive, efficient, and rapid detection of UA has far-reaching significance in clinical diagnosis and disease prevention. Herein, a novel coordination polymer constructed by dual-ligand was successfully prepared, which exhibited excellent thermal and water stability. The polymer was interlaced by coordination bonds and hydrogen bonds to form an infinitely extended three-dimensional framework, which showed a rare and novel topological structure. The complex selectively recognized UA through significant fluorescence quenching response in the presence of various interferences. The excellent detection sensitivity (the limited detection of 1.2 μM), outstanding anti-interference ability and remarkable recyclability marked the complex to be a promising sensor material towards UA. In addition, the detection mechanism of UA by the complex was investigated in detail by combining density functional theory (DFT) and a variety of other analytical methods.

Enhanced Tb(III) fluorescence on gelatin-coated silver nanoparticles in dopamine detection

A composite fluorescent nanoprobe based on metal enhanced fluorescence (MEF) effect of gelatin-coated silver nanoparticles (AgNPs@gel) was developed for selective and sensitive detection of dopamine (DA). The characteristic fluorescence of Tb(III) was using as the detection signal and AgNPs@gel served as substrates of the MEF. Gelatin with rich amine and carboxylic groups was used not only as a co-ligand of Tb(III) complex, but also as a bridging substance and a spacing material for improving the MEF of AgNPs@gel on the intrinsic luminescent intensity of Tb(III). Under the optimal conditions, the increment of the fluorescence intensity (measured at 307/544 nm as excitation/emission wavelength) of the system increased linearly with the concentration of DA in the range of 0.80-100 nM (R² = 0.9937) and 100-1000 nM (R² = 0.9978). The fluorescent probe greatly improved Tb(III) luminescence, which paved the way for sensitive detection with a low detection limit of 0.54 nM. It also showed good selectivity among other neurotransmitters. This work was successfully applied to the determination of DA in human serum samples with recoveries ranging from 99.8 to 102.2%. We believe that the Tb(III)-DA-AgNPs@gel composite fluorescent probe can be developed as a new approach for DA detection.

Precisely Controlled Vertical Alignment in Mesostructured Carbon Thin Films for Efficient Electrochemical Sensing

Two-dimensional carbon materials, incorporating a large mesoporosity, are attracting considerable research interest in various fields such as catalysis, electrochemistry, and energy-related technologies owing to their integrated functionalities. However, their potential applications, which require favorable mass transport within mesopore channels, are constrained by the undesirable and finite mesostructural configurations due to the immense synthetic difficulties. Herein, we demonstrate an oriented monomicelle assembly strategy, for the facile fabrication of highly ordered mesoporous carbon thin films with vertically aligned and permeable mesopore channels. Such a facile and reproducible approach relies on the swelling and fusion effect of hydrophobic benzene homologues for directional monomicelle assembly. The orientation assembly process shows precise controllability and great universality, affording mesoporous carbon films with a cracking-free structure over a centimeter in size, highly tunable thicknesses (13 to 85 nm, an interval of ∼12 nm), mesopore size (8.4 to 13.5 nm), and switchable growth substrates. Owing to their large permeable mesopore channels, electrochemical sensors based on vertical mesoporous carbon films exhibit an ultralow limit of detection (50 nmol L^-1) and great sensitivity in dopamine detection.

Detection of ascorbic acid based on its quenching effect on luminol-artemisinin chemiluminescence

We find that luminol can react with artemisinin (ART) to produce chemiluminescence (CL) in the absence of a catalyst and ascorbic acid (AA) can quench luminol-ART CL. Based on its efficient inhibition effect on luminol-ART CL, a new AA detection method is established. The calibration curve for the determination of AA is in the linear range of 5 × 10^-7 M to 1 × 10^-4 M with a detection limit of 50 nM, which is more sensitive than many other reported methods. This CL approach was utilized to detect AA in vitamin C tablets by applying the standard addition method, and the recoveries of 104.0%, 96.8% and 103.4% were obtained, respectively, at concentrations of 1 μM, 5 μM and 10 μM with a RSD value of less than 3.6%. This developed method for AA assay is distinguished by its fastness, reproducibility, easy operation and good selectivity.

Wearable and Implantable Intraocular Pressure Biosensors: Recent Progress and Future Prospects

Biosensors worn on or implanted in eyes have been garnering substantial attention since being proven to be an effective means to acquire critical biomarkers for monitoring the states of ophthalmic disease, diabetes. Among these disorders, glaucoma, the second leading cause of blindness globally, usually results in irreversible blindness. Continuous intraocular pressure (IOP) monitoring is considered as an effective measure, which provides a comprehensive view of IOP changes that is beyond reach for the "snapshots" measurements by clinical tonometry. However, to satisfy the applications in ophthalmology, the development of IOP sensors are required to be prepared with biocompatible, miniature, transparent, wireless and battery-free features, which are still challenging with many current fabrication processes. In this work, the recent advances in this field are reviewed by categorizing these devices into wearable and implantable IOP sensors. The materials and structures exploited for engineering these IOP devices are presented. Additionally, their working principle, performance, and the potential risk that materials and device architectures may pose to ocular tissue are discussed. This review should be valuable for preferable structure design, device fabrication, performance optimization, and reducing potential risk of these devices. It is significant for the development of future practical IOP sensors.

Amperometric sensor based on ZIF/g-C3N4/RGO heterojunction nanocomposite for hydrazine detection

A dense  zeolitic imidazolate framework (ZIF) nanosheet is for the first time molded by reduced graphite oxide (RGO) and graphitic carbon nitride (g-C₃N₄) to fabricate an original 2D/2D/2D heterojunction (ZIF/g-C₃N₄/RGO nanohybrid), which is pipetted onto carbon cloth electrode (CCE) (ZIF/g-C₃N₄/RGO/CCE) as an electrochemical sensor. Profiting from the renowned synergistic and coupling effects, the resulting nanohybrid endows excellent electrocatalytic activity towards hydrazine. Amperometric detection reveals that the hybrid sensor possesses a low detection limit of 32 nM (S/N = 3) in a monitoring range of 0.0001 to 1.0386 mM, along with a high sensitivity 93.71 μA mM^-1 cm^-2. Importantly, the minimum detection concentration of hydrazine in the actual sample is lower than the maximum allowable limit of the World Health Organization (WHO) and has high reproducibility (RSD = 4.82%). As expected, the high sensing capability  of ZIF/g-C₃N₄/RGO combines the advantages of abundant surface-active sites and high conductivity along with 2D interfaces between ZIF, g-C₃N₄, and RGO nanosheets. This study provides a promising to expand 2D-based ternary nanojunction as a bridge for promoting sensing performance.Graphical abstract.

A novel electrochemical paper sensor for low-cost detection of 5-methyltetrahydrofolate in egg yolk

An electrochemical deposition method was used to fabricate a gold nanoflower (AuNF) and carbon nanoparticle (CNP) modified carbon paper (CP) sensor (AuNFs-CNPs/CP) for the low-cost detection of 5-methyltetrahydrofolate (5-mTHF) in egg yolk. AuNF morphology and structures were characterized by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS), revealing nanoflower sizes in the 50 to 200 nm range. AuNFs formed on the sensor were in the Au⁰. We evaluated 5-mTHF assay performance using cyclic voltammetry, differential pulse voltammetry and chronoamperometry. The AuNFs-CNPs/CP sensor detected 5-mTHF concentrations in the ranges from 1 to 5 mg L^-1 and 1-20 μg L^-1, with an excellent limit of detection of 1 μg L^-1 and good selectivity toward 5-mTHF, when compared to other potentially interfering molecules in samples. The AuNFs-CNPs/CP sensor was also used to detect 5-mTHF in folate-rich, and was found to be twice than that of ordinary egg yolk.

Solid-phase microextraction integrated nanobiosensors for the serial detection of cytoplasmic dopamine in a single living cell

Dopamine participates in many physiological and pathological processes. Dynamic monitoring of dopamine levels in the cytoplasm of a single living cell reflects not only the functional state of dopamine synthesis factors but also the processes of related neurodegenerative diseases. Due to the low content of cytoplasmic dopamine and the difficulty to keep cells alive during the operating process, the detection of cytoplasmic dopamine is still challenging. Herein, a solid-phase microextraction (SPME) technique integrated nanobiosensor was employed to trace and quantify dopamine concentration fluctuations in the cytoplasm of a single living cell. We designed a polypyrrole modified carbon fiber nanoprobe as a bifunctional nanoprobe that can extract cytoplasmic dopamine and then perform electrochemical detection. This bifunctional nanoprobe can detect 10 pmol/L extracted dopamine and detected a 60% decrease of the cytoplasmic dopamine concentration in a single living cell by K⁺ stimulation. This study allowed for the first time serially detecting cytoplasmic dopamine while keeping the target cell alive, which might yield a new method for research on dopamine neurotoxicity and the related drug action mechanisms for neurodegenerative disease.

Simultaneous Detection of Ascorbic Acid, Dopamine, and Uric Acid Using a Novel Electrochemical Sensor Based on Palladium Nanoparticles/Reduced Graphene Oxide Nanocomposite

A fresh strategy based on two-step electrochemical reduction for the fabrication of palladium nanoparticles/reduced oxide nanocomposite-modified glass carbon electrode (PdNPs/rGO/GCE) was established in this study. Field emission scanning electron microscopy (FESEM) images showed that spherical PdNPs were evenly distributed on the surface of rGO-modified electrode (rGO/GCE), and the introduction of PdNPs has no effect on the morphology of rGO. Electrochemical impedance spectroscopy (EIS) studies revealed that the conductivity of PdNPs/rGO/GCE was higher than that of rGO/GCE and bare GCE. The electrochemical performances of PdNPs/rGO/GCE sensor were investigated by cyclic voltammetry (CV), differential pulse voltammetry (DPV), and chronoamperometry using ascorbic acid (AA), dopamine (DA), and uric acid (UA) as analytes. At the optimized conditions, wide linear ranges of 0.5–3.5 mM (R² = 0.99), 3–15 μM (R² = 0.99) and 15–42 μM (R² = 0.99), and 0.3–1.4 mM (R² = 0.99) towards AA, DA, and UA in ternary mixture were observed, respectively. In addition to superior anti-interference capability, fast response (≤5 s), excellent reproducibility, and good long-term stability were also given by this sensor. These results suggested that PdNPs/rGO/GCE is promising for the simultaneous detection of AA, DA, and UA in practical application.

Holey nitrogen-doped graphene aerogel for simultaneously electrochemical determination of ascorbic acid, dopamine and uric acid

In this paper, holey nitrogen-doped graphene aerogel (HNGA) was synthesized and applied to the concurrently electrochemical determination of small biological molecules including ascorbic acid (AA), dopamine (DA) and uric acid (UA). Firstly, holey graphene hydrogel was synthesized by the hydrothermal reaction in the presence of H₂O₂, which subsequently was lyophilized and further annealed in the mixed gas of ammonia and argon to obtain HNGA. Electron microscopy characterization exhibited a great number of nanopores formed on the basal surface of graphene sheets, and HNGA possessed a hierarchically porous structure. The unique structure and composition of HNGA make it an ideal material for electroanalytical application through accelerating mass and electron transfer. HNGA modified glassy carbon electrode (HNGA/GCE) displayed significantly enhanced electrochemical response to AA, DA, and UA, namely reducing overpotential, increasing current density, and improving the reversibility. The oxidation peaks of these three biomolecules can be entirely separated with evident peak potential differences which are 0.216 V (AA-DA), 0.120 V (DA-UA), and 0.336 V (AA-UA), which it allowed the determination of the three substances at the same time. This sensor shows high sensitivity for the determination of AA, DA, and UA with the detection limit of 16.7 μM, 0.22 μM, and 0.12 μM (S/N = 3), respectively. The proposed sensor was applicable for the practical sample analysis as well and desirable recovery was obtained.

Porous Fiber Processing and Manufacturing for Energy Storage Applications

The objective of this article is to provide an overview on the current development of micro- and nanoporous fiber processing and manufacturing technologies. Various methods for making micro- and nanoporous fibers including co-electrospinning, melt spinning, dry jet-wet quenching spinning, vapor deposition, template assisted deposition, electrochemical oxidization, and hydrothermal oxidization are presented. Comparison is made in terms of advantages and disadvantages of different routes for porous fiber processing. Characterization of the pore size, porosity, and specific area is introduced as well. Applications of porous fibers in various fields are discussed. The emphasis is put on their uses for energy storage components and devices including rechargeable batteries and supercapacitors.

Electrochemical detection of ascorbic acid in artificial sweat using a flexible alginate/CuO-modified electrode

A flexible sensor is presented for electrochemical detection of ascorbic acid in sweat based on single-step modified gold microelectrodes. The modification consists of electrodeposition of alginate membrane with trapped CuO nanoparticles. The electrodes are fabricated at a thin polyimide support and the soft nature of the membrane can withstand mechanical stress beyond requirements for skin monitoring. After characterization of the membrane via optical and scanning electron microscopy and cyclic voltammetry, the oxidative properties of CuO are exploited toward ascorbic acid for amperometric measurement at micromolar levels in neutral buffer and acidic artificial sweat, at ultralow applied potential (- 5 mV vs. Au pseudo-reference electrode). Alternatively, measurement of the horizontal shift of redox peaks by cyclic voltammetry is also possible. Obtaining a limit of detection of 1.97 μM, sensitivity of 0.103 V log (μM)^-1 of peak shift, and linear range of 10-150 μM, the effect of possible interfering species present in sweat is minimized, with no observable cross-reaction, thus maintaining a high degree of selectivity despite the absence of enzymes in the fabrication scheme. With a lateral flow approach for sample delivery, repeated measurements show recovery in few seconds, with relative standard deviation of about 20%, which can serve to detect increased loss or absence of vitamin, and yet be improved in future by optimized device designs. This sensor is envisioned as a promising component of wearable devices for e.g. non-invasive monitoring of micronutrient loss through sweat, comprising features of light weight, low cost, and easy fabrication needed for such application. Graphical Abstract Schematic depiction of the cyclic voltammetry signal change as the sweat flows over the sensor surface.

Nature inspired poly (dopamine quinone -vanadyl) as new modifier for voltammetric determination of uric acid

The preparation of a novel polymer (poly(dopamine quinone-vanadyl) (polyDQV)) bearing dopaminequinone and VO^IV redox groups is described. PolyDQV was characterized using field emission scanning electron microscopy (FESEM), energy dispersive x-ray spectroscopy, x-ray photoelectron spectroscopy (XPS), Fourier transform infra-red (FTIR) spectroscopy, UV-Vis spectroscopy as well as electrochemical methods such as differential pulse voltammetry, cyclic voltammetry, and electrochemical impedance spectroscopy (EIS). The electrocatalytic activity of polyDQV was studied toward electrooxidation of uric acid using differential pulse voltammetry as well as cyclic voltammetry. PolyDQV presents interesting electrocatalytic activity toward UA oxidation in phosphate buffer solution (0.1 M, pH 2) to a well-defined oxidation peak at 0.65 V (vs. Ag/AgCl). The polyDQV-modified carbon paste electrode (CPE/polyDQV) presents a precise linear signal-concentration relationship in the ranges of 0.3-5 μM and 5 to 200 μM with a detection limit (S/N = 3) of 0.02 μM. The %RSD values for ten replicate measurements of 0.5 and 50 μM UA were 1.8 and 3%, respectively, indicating good repeatability of analytical signals. Appropriate recovery values (in the range 96 to 103%) and good selectivity for UA over common coexisting species (such as ascorbic acid and dopamine) exhibit that CPE/polyDQV is a promising novel platform for sensing UA in human blood serum and urine samples. Graphical abstract.

Sensitive electrochemical sensing platform for selective determination of dopamine based on amorphous cobalt hydroxide/polyaniline nanofibers composites

In this study, amorphous cobalt hydroxide/polyaniline nanofibers (Co(OH)₂/PANINF) composites were successfully prepared. The formation of amorphous Co(OH)₂ with irregular surface structure was confirmed by x-ray diffraction, scanning electron microscopy, and selected-area electron diffraction. The non-enzymatic electrochemical sensor for the selective and sensitive determination of dopamine (DA) has been constructed by using Co(OH)₂/PANINF composites modified glassy carbon electrode (Co(OH)₂/PANINF/GCE), which exhibited excellent electrocatalytic activity toward DA, in a large part owing to the advantages of large surface area of amorphous Co(OH)₂ and the synergetic effect between Co(OH)₂ and PANINF. The electrochemical kinetics reveal that the DA oxidation involves two electrons and two protons in a quasi-reversible electrode reaction. Differential pulse voltammetry (DPV) studies show remarkable sensing performance for the determination of DA, with a low detection limit of 0.03 μM, and a wide linear range from 0.1 to 200 μM. From a broader perspective, the present study demonstrates that Co(OH)₂/PANINF composites would be promising supporting materials for novel sensing platforms.