Sonochemical-assisted synthesis of CuO/Cu2O/Cu nanoparticles as efficient photocatalyst for simultaneous degradation of pollutant dyes in rotating packed bed reactor: LED illumination and central composite design optimization

Ultrasonic-assisted nanofiltration separation recovering salvianolic acid B from ethanol wastewater

The transformation of salvianolic acid B brought on by heat treatment recovery of ethanol eluent, which is a difficult problem in pharmaceutical technology, affects the purity of raw material when the medicinal raw material salvianolic acid B is purified by resin. Ultrasonic-assisted nanofiltration separation (UANS) was first employed to improve efficiency of resource utilization by regulating rejection and separating salvianolic acid B and rosmarinic acid from organic pharmaceutical wastewater. The rejection was related to three variables: ultrasonic power, pH, and ethanol concentration. But there were differences in the effects of variables on the rejections of salvianolic acid B and rosmarinic acid. The rejections of rosmarinic acid and salvianolic acid B showed a decreasing trend with an increase in ultrasonic power or a decrease in pH; however, when the concentration of ethanol was increased from 5 % to 35 %, the salvianolic acid B rejection increased from 84.96 % to 96.60 % and the rosmarinic acid rejection decreased from 35.09 % to 17.51 %. On the basis of response surface methodology (RSM), the optimal UANS parameters for solution conditions involving different ethanol concentrations are as follows: 10 % ethanol solution (ultrasonic power 500 W and pH 6.15), 20 % ethanol solution (ultrasonic power 500 W and pH 6.54), and 30 % ethanol solution (ultrasonic power 460 W and pH 6.34). The molecular proportions of salvianolic acid B were 10.75 %, 7.13 %, and 8.27 % in 10 %, 20 %, and 30 % ethanol wastewater, while the molecular proportions of rosmarinic acid were 40.52 %, 33.83 %, and 69.87 %, respectively. And the recoveries of salvianolic acid B in 10 %, 20 %, and 30 % ethanol wastewater were 93.56 %, 95.04 %, and 97.30 %, respectively, while the recoveries of rosmarinic acid were 3.19 %, 2.27 %, and 0.56 %. The molecular proportion and the rejection are correlated exponentially. In comparison with conventional nanofiltration separation (CNS), UANS is able to resolve the conflict between rosmarinic acid and salvianolic acid B in pharmaceutical wastewater, as well as enhance resource recycling and separation efficiency to prevent pollution of the environment from pharmaceutical wastewater. Experiments using UANS at different power intensities suggest that the ultrasonic at a power intensity of 46-50 W/L and the power density of 0.92-1.00 W/cm2 may resolve the separation conflict between rosmarinic acid and salvianolic acid B. This work suggests that UANS may be a significant advancement in the field of ultrasonic separation and has several potential uses in the water treatment industry.

Ultrasonic-assisted activated carbon separation removing bacterial endotoxin from salvia miltiorrhizae injection

Ultrasonic-assisted activated carbon separation (UACS) was first employed to improve product quality by regulating adsorption rate and removing bacterial endotoxin from salvia miltiorrhizae injection. The adsorption rate was related to three variables: activated carbon dosage, ultrasonic power, and pH. With the increase of activated carbon dosage from 0.05 % to 1.0 %, the adsorption rates of salvianolic acids and bacterial endotoxin increased simultaneously. The adsorption rates at which bacteria endotoxins increased from 52.52 % to 97.16 % were much higher than salvianolic acids. As the ultrasonic power increased from 0 to 700 W, the adsorption rates of salvianolic acids on activated carbon declined to less than 10 %, but bacterial endotoxin increased to more than 87 %. As the pH increased from 2.00 to 8.00, the adsorption rate of salvianolic acid dropped whereas bacterial endotoxin remained relatively stable. On the basis of response surface methodology (RSM), the optimal separation conditions were established to be activated carbon dose of 0.70 %, ultrasonic power of 600 W, and pH of 7.90. The experimental adsorption rates of bacterial endotoxin were 94.15 %, which satisfied the salvia miltiorrhizae injection quality criterion. Meanwhile, salvianolic acids' adsorption rates were 1.92 % for tanshinol, 4.05 % for protocatechualdehyde, 2.21 % for rosmarinic acid, and 3.77 % for salvianolic acid B, all of which were much lower than conventional activated carbon adsorption (CACA). Salvianolic acids' adsorption mechanism on activated carbon is dependent on the component's molecular state. Under ideal separation conditions, the molecular states of the four salvianolic acids fall between 1.13 % and 6.60 %. The quality of salvia miltiorrhizae injection can be improved while maintaining injection safety by reducing the adsorption rates of salvianolic acids to less than 5 % by the use of ultrasound to accelerate the desorption mass transfer rate on the activated carbon surface. When activated carbon adsorption was used in the process of producing salvia miltiorrhizae injection, the pH of the solution was around 5.00, and the proportion of each component's molecular state was tanshinol 7.05 %, protocatechualdehyde 48.93 %, rosmarinic acid 13.79 %, and salvianolic acid B 10.28 %, respectively. The loss of useful components was evident, and the corresponding activated carbon adsorption rate ranged from 20.74 % to 41.05 %. The average variation rate in plasma His and IgE was significant (P < 0.05) following injection of 0.01 % activated carbon, however the average variation rate of salvia miltiorrhizae injection was dramatically decreased with the use of UACS and CACA (P > 0.05). The ultrasonic at a power intensity of 60 W/L and the power density of 1.20 W/cm2 may resolve the separation contradiction between salvianolic acids and bacterial endotoxin, according to experiments conducted with UACS at different power intensities. According to this study, UACS has a lot of potential applications in the pharmaceutical manufacturing industry and may represent a breakthrough in the field of ultrasonic separation.

Eco-friendly and sustainable basil seed hydrogel-loaded copper hydroxide-based catalyst for the synthesis of propargylamines and tetrazoles

The broad use of propargyl amines and tetrazoles in pharmaceutical applications presents a well-established challenge. Their synthesis relies heavily on catalysis, which, in turn, has been hindered by the scarcity of stable and practical catalysts. In response to this issue, we have developed an environmentally friendly and sustainable catalyst by infusing copper hydroxide into basil seed hydrogel (Cu(OH)2-BSH), creating a 3D nanoreactor support structure. To verify the structural, physical, chemical, and morphological properties of the prepared samples, a comprehensive analysis using various techniques, including FT-IR, EDX, FE-SEM, TEM, XRD, BET, TGA, and XPS, were conducted. The results not only confirmed the presence of Cu(OH)2 but also revealed a porous structure, facilitating faster diffusion and providing a substantial number of active sites. This catalyst boasts a high surface area and can be easily recovered, making it a cost-effective, safe, and readily available option. This catalyst was applied to the synthesis of propargyl amines and tetrazoles through multi-component reactions (MCRs), achieving excellent results under mild conditions and in a remarkably short timeframe. Consequently, this work offers a straightforward and practical approach for designing and synthesizing metal hydroxides and 3D hydrogels for use in heterogeneous catalysis during organic syntheses. This can be achieved using basic and affordable starting materials at the molecular level.

Proficient sonophotocatalytic degradation of organic pollutants using Co3O4/TiO2 nanocomposite immobilized on zeolite: Optimization, and artificial neural network modeling

The health of all living organisms is greatly influenced by the quality of the water. Therefore, developing cost-effective, eco-friendly, and easily accessible methods is desperately needed to meet the high global demand for clean water. Recently, nanozyme-based dye degradation methods have been promising for the remediation of water pollution. In this work, peroxidase-mimic Co3O4/TiO2 nanocomposite was synthesized and characterized for its size, morphology, and crystalline structure. Colorimetric assay results showed that the peroxidase-like activity of the Co3O4/TiO2 nanocomposite was considerably enhanced compared to the pure Co3O4 NPs and TiO2 NPs. Besides excellent enzyme-mimic activity, the higher sonophotocatalytic dye degradation capability of the nanocomposite after immobilization on zeolite (Co3O4/TiO2@Ze) was also demonstrated. Under optimal conditions (pH = 5.0, 25 °C), 0.1 g/L of catalyst was able to degrade 100 % of methylene blue (MB) with 600 μM in the presence of 30 μM H2O2 within 12 min. GC/MS analysis and toxicity studies revealed less toxic metabolite production after treatment of MB with sonophotocatalytic Co3O4/TiO2@Ze. Modeling of MB degradation using artificial neural networks (ANN) with a 5:6:1 topology was successfully performed, and the results confirmed the fitness of theoretical and experimental outputs according to the calculated correlation coefficient values. The prepared nanocomposite could thus be used as a promising and highly effective catalyst for the removal of organic dyes from polluted water.

Mixed valence copper oxide composites derived from metal-organic frameworks for efficient visible light fuel denitrification

The construction of heterojunctions has been used to optimize photocatalyst fuel denitrification. In this work, HKUST-1(Cu) was used as a sacrificial template to synthesize a composite material CuxO (CuO/Cu2O) that retains the original MOF framework for photocatalytic fuel denitrification by calcination at different temperatures. By adjusting the temperature, the content of CuO/Cu2O can be changed to control the performance and structure of CuxO-T effectively. The results show that CuxO-300 has the best photocatalytic performance, and its denitrification rate reaches 81% after 4 hours of visible light (≥420 nm) irradiation. Through the experimental analysis of pyridine's infrared and XPS spectra, we found that calcination produces CuxO-T mixed-valence metal oxide, which can create more exposed Lewis acid sites in the HKUST-1(Cu) framework. This leads to improved pyridine adsorption capabilities. The mixed-valence metal oxide forms a type II semiconductor heterojunction, which accelerates carrier separation and promotes photocatalytic activity for pyridine denitrification.

Recent progress on sonochemical production for the synthesis of efficient photocatalysts and the impact of reactor design

Sonochemical-assisted synthesis has flourished recently for the design of photocatalysts. The main power used is ultrasound that allows the nanomaterials shape and size modification and control. This review highlights the effect in formation mechanism by ultrasound application and the most common photocatalysts that were prepared via sonochemical techniques. Moreover, the challenge for the suitable reactor design for the synthesis of materials or for their photocatalytic evaluation is discussed since the most prominent reactor systems, batch, and continuous flow, has both advantages and drawbacks. This work summarises the significance of sonochemical synthesis for photocatalytic materials as a green technology that needs to be further investigated for the preparation of new materials and the scale up of developed reactor systems to meet industrial needs.

Graphene-based photocatalysts for degradation of organic pollution

Compared with the traditional wastewater treatment technology, semiconductor photocatalysis is a rapidly emerging environment-friendly and efficient Advanced Oxidation Process for degradation of refractory organic contaminants. Single-component semiconductor photocatalysts exhibit poor photocatalytic performance and cannot meet the requirements of wastewater treatment. The combination of semiconductor photocatalysts and Graphene can effectively improve the photocatalytic activity and stability of semiconductor photocatalysts. This review focuses on the synergistic effect of several types of semiconductors with Graphene for photocatalytic degradation of organic pollutants. After a brief introduction of the photodegradation mechanism of semiconductor materials and the basic description of Graphene, the synthesis, characterization and degradation performance of various Graphene-based semiconductor photocatalysts are emphatically introduced.

Sonochemical synthesis and characterization of Sm2CuO4 nanostructures and their application as visible-light photocatalyst for degradation of water-soluble organic pollutants

In recent years, water contamination has become a significant crisis, and it is crucial to find new materials that can efficiently eliminate these contaminants. The current work presents the Sm2CuO4 nanophotocatalyst for the decolorization of different water-soluble organic contaminants. The fabrication of Sm2CuO4 nanostructures was achieved using a simple and rapid sonochemical pathway, resulting in an optical bandgap of 1.62 eV as determined by diffuse reflectance spectroscopy. Several factors, including different organic contaminants, organic contaminant concentrations, Sm2CuO4 dosages, and the pH of the media, were scrutinized to achieve the best efficiency. The results manifested that Sm2CuO4 was highly effective in removing different organic contaminants from water. For example, when 30 mg of Sm2CuO4 was used with 20 mg L-1 methyl orange under visible irradiation for 100 min, 91.4% of the methyl orange was destroyed. Further investigation revealed that holes (h+) were primarily responsible for pollutant photodegradation when using Sm2CuO4 as a photocatalyst. This finding suggests that Sm2CuO4 could be an excellent candidate for developing new materials to effectively remove water contaminants.

Synthesis of Cu and CuO nanoparticles from e-waste and evaluation of their antibacterial and photocatalytic properties

Waste printed circuit boards (WPCBs) contain a plethora of valuable metals, considered an attractive secondary resource. In the current research, a hydrometallurgical process combined ammonia/ammonium chloride leaching and reduction (using L-ascorbic acid) to recover copper and its oxide (CuO) as nanosized particles from WPCBs was investigated. The results of leaching indicated that 96.7% of copper could be recovered at a temperature of 35 °C for a leaching duration of 2 h with ammonium chloride and ammonia concentration of 2 mol/L at a solid:liquid ratio of 1:10 g/cm3. The synthesized particles exhibit spherical and distorted sphere morphology with average particle size of 460 nm and 50 nm for Cu and CuO NPs, respectively. The antibacterial activity of Cu, CuO, and a (1:1) blend of both (Cu/CuO) has been examined against five different bacterial and fungal strains. The highest zone of inhibition was measured as 21.2 mm for Cu NPs toward Escherichia coli and 16.7 mm for Cu/CuO blend toward Bacillus cereus bacteria. The highest zone of inhibition was measured as 13 mm and 13.8 mm for Cu/CuO blend toward Fusarium proliferatum and Penicillium verrucosum fungi. Cu/CuO blend showed notable photocatalytic activity towards Rhodamine B dye under visible light irradiation with 96% degradation rate within 120 min. Using the process developed in this study, copper and its oxide as nanoparticles can be produced from WPCBs and used for multifunctional applications.

Insights into the Degradation Mechanisms of TCH by Magnetic Fe3S4/Cu2O Composite

Unique Fe₃S₄/Cu₂O composites were constructed with high Fenton-like photocatalytic activity through the impregnation coprecipitation method. The structure, morphology, optical, magnetic, and photocatalytic properties of the as-prepared composites were explored in detail. The findings suggest that small Cu₂O particles were grown on the surface of Fe₃S₄. The removal efficiency of TCH by Fe₃S₄/Cu₂O was 65.7, 4.75, and 3.67 times higher than that of pure Fe₃S₄, Cu₂O, and the Fe₃S₄ + Cu₂O mixture, respectively, when the mass ratio of Fe₃S₄ and Cu₂O was 1:1 at pH 7.2. The synergistic effect between Cu₂O and Fe₃S₄ was the main factor for TCH degradation. The Cu⁺ species from Cu₂O increased the Fe³⁺/Fe²⁺ cycle during the Fenton reaction. ^•O₂^- and h⁺ were the main active radicals; however, ^•OH and e^- played the second role in the photocatalytic degradation reaction. Moreover, the Fe₃S₄/Cu₂O composite retained good recyclability and versatility, and could be conveniently separated by a magnet.

Copper oxide nanoparticles: In vitro and in vivo toxicity, mechanisms of action and factors influencing their toxicology

Copper oxide nanoparticles (CuO NPs) have received increasing interest due to their distinctive properties, including small particle size, high surface area, and reactivity. Due to these properties, their applications have been expanded rapidly in various areas such as biomedical properties, industrial catalysts, gas sensors, electronic materials, and environmental remediation. However, because of these widespread uses, there is now an increased risk of human exposure, which could lead to short- and long-term toxicity. This review addresses the underlying toxicity mechanisms of CuO NPs in cells which include reactive oxygen species generation, leaching of Cu ion, coordination effects, non-homeostasis effect, autophagy, and inflammation. In addition, different key factors responsible for toxicity, characterization, surface modification, dissolution, NPs dose, exposure pathways and environment are discussed to understand the toxicological impact of CuO NPs. In vitro and in vivo studies have shown that CuO NPs cause oxidative stress, cytotoxicity, genotoxicity, immunotoxicity, neurotoxicity, and inflammation in bacterial, algal, fish, rodents, and human cell lines. Therefore, to make CuO NPs a more suitable candidate for various applications, it is essential to address their potential toxic effects, and hence, more studies should be done on the long-term and chronic impacts of CuO NPs at different concentrations to assure the safe usage of CuO NPs.

Efficient utilization of free radicals in advanced oxidation processes under high-gravity environment for disposing pollutants in effluents and gases: A critical review

Advanced oxidation processes (AOPs) using strongly oxidizing radicals are promising for wastewater treatment and gas purification. Nevertheless, the short half-life of radicals and the limited mass transfer in traditional reactors cause under-utilization of radicals and low pollutant removal efficiency. High-gravity technology (HiGee)-enhanced AOPs (HiGee-AOPs) have been demonstrated a promising way to enhance radical utilization in a rotating packed bed reactor (RPB). Here, we review the potential mechanisms of intensified radical utilization in HiGee-AOPs, structures and performance of RPB, and applications of HiGee in AOPs. The intensification mechanisms are described from three aspects: enhanced generation of radicals by efficient mass transfer, in-situ radical utilization under frequent liquid film renewal, and selective effect on radical utilization due to micromixing in RPB. Based on these mechanisms, we propose a novel High-gravity flow reaction with the essence of efficiency, in-situ, and selectivity in order to better explain the strengthening mechanisms in HiGee-AOPs. HiGee-AOPs possess great potential for treating effluent and gaseous pollutants due to characteristics of High-gravity flow reaction. We discuss the pros and cons of different RPBs and their applications to specific HiGee-AOPs. HiGee improve the following AOPs: (1) facilitate interfacial mass transfer in homogeneous AOPs, (2) enhance mass transfer to expose more catalytically active sites and mass-produce nanocatalysts for heterogeneous AOPs, (3) inhibit bubble accumulation on the electrode surface of electrochemical AOPs, (4) increase the mass transfer between liquid and catalysts in UV-assisted AOPs, (5) improve the micromixing efficiency of ultrasound-based AOPs. Strategies outlined in this paper should inspire further development of HiGee-AOPs.

Dynamic removal of Pb(II) by live Dunaliella salina: a competitive uptake and isotherm model study

The main aim of this study is modeling of a continuous biosorption system for the removal of Pb(II) ions in the aqueous conditions using live Dunaliella salina microalgae. The live microalgae can grow in saline water and opens new opportunities in varying the amount and properties of biosorbent. The effects of five parameters, including pH, optical density of algae as a factor indicating the adsorbent dosage, injection time, contact time, and initial concentration of Pb(II), were optimized by means of response surface methodology (RSM) based on the central composite design (CCD). Dunaliella salina algae showed maximum Pb(II) biosorption with 96% efficiency. For the selective Pb(II) uptake in the presence of Cd(II) and Ni(II), binary and ternary systems of ions were chosen. The mutual effect of each heavy metal ion in all systems on the total uptake percentage was also examined. The ion selectivity was investigated in the presence of diverse heavy metal ions, and the Pb(II) uptake percentage was determined to be 80%. Both Langmuir and Freundlich isotherm models were suitable for describing multicomponent binary and ternary systems depending on the presence of competitive ions in the mixture. Main functional groups and surface properties of the Dunaliella salina were identified by Fourier transform infrared spectroscopy, scanning electron microscopy, and energy dispersive spectrometry. Hence, effective heavy metal ion uptake, simple design, and cost-effective cultivation confirmed live Dunaliella salina as suitable microalgae for purifying contaminated water in an economic and safe manner.

CuO improved energy band of AgO/fibrous SiO2-ZrO2 for optimized simultaneous photocatalytic redox of chromium (VI) and p-cresol using response surface methodology

Ternary CuO/AgO/FSZr photocatalysts were fabricated via the hydrothermal and electrochemical methods with three different CuO loading (1, 3 and 5 wt%), indicated as 1CuO/AgO/FSZr, 3CuO/AgO/FSZr and 5CuO/AgO/FSZr. The photocatalytic reaction was tested towards simultaneous chromium (VI) photoreduction and p-cresol photooxidation and the performance in order as follow: 3CuO/AgO/FSZr > 5CuO/AgO/FSZr > 1CuO/AgO/FSZr > AgO/FSZr > FSZr. CuO/AgO/FSZr photocatalysts showed an improvement in photocatalytic activity compared to AgO/FSZr and FSZr due to the reduction potential of chromium (VI) aligned closer to the conduction band of CuO and provided abundant free active electrons (e^-) and holes (h⁺) with efficient transportation and migration. Interestingly, the 3CuO/AgO/FSZr was established as the best photocatalyst with 98% reduction of chromium (VI) and 83% oxidation of p-cresol simultaneously, owing to its strong corporation between the metal oxides and support and higher total pore volume. The Langmuir-Hinshelwood model were employed for kinetics which followed the pseudo-first-order kinetics model well. Based on the simultaneous photocatalytic mechanism, chromium (VI) and p-cresol were directly reduced and oxidized by e^- and h⁺, respectively. The response surface methodology (RSM) discovered that the quadratic term initial concentration of chromium (VI) is the main significant factor in photocatalytic performance. The optimum parameters for simultaneous photoredox of chromium (VI) and p-cresol predicted from RSM are 9.6 mg L^-1 of chromium (VI) concentration, 9.8 mg L^-1 of p-cresol concentration and 0.32 g L^-1 of catalyst dosage. Under these conditions the error between the predicted and experimental values is only 3.7%. The 3CuO/AgO/FSZr sustained the photocatalytic performance after reused for five cycles and could oxidized various organic pollutants as well as reduced chromium (VI) simultaneously.

Insights on applications of bentonite clays for the removal of dyes and heavy metals from wastewater: a review

In recent decades, increased industrial, agricultural, and domestic activities have resulted in the release of various pollutants into the aquatic systems, which require a reliable and environmentally friendly method to remove them. Adsorption is one of the most cost-effective and sustainable wastewater treatment techniques. A plethora of low-cost bio-based adsorbents have been developed worldwide so far to supplant activated carbon and its high processing costs. Bentonite clays (BCs), whether in natural or modified form, have gained enormous potential in wastewater treatment and have been used successfully as a novel and cost-effective bio-sorbent for removing organic and inorganic pollutants from the liquid suspension. It has become a sustainable solution for wastewater treatment due to its variety of surface and structural properties, superior chemical stability, high capacity for cation exchange, elevated surface area due to its layered structure, non-toxicity, abundance, low cost, and high adsorption capacity compared to other clays. This review encompasses comprehensive literature about various modification techniques and adsorption mechanisms of BCs concerning dyes and heavy metal removal from wastewater. A critical overview of different parameters for optimizing adsorption capacity and regeneration via the desorption technique has also been presented here. Finally, a conclusion has been drawn with some future research recommendations based on technological challenges encountered in industrializing these materials.

WO3/Ag/ZnO S-scheme heterostructure thin film spinning disc photoreactor for intensified photodegradation of cephalexin antibiotic

The presence of antibiotics in wastes and drinking water has led to serious environmental and health concerns, further necessitating the development of an advanced sustainable strategy to eliminate antibiotics from aquatic media. In this context, the present research reports the successful fabrication of a spinning disc photoreactor (SDPR) supported ZnO/Ag/WO₃ S-scheme visible-light-driven thin-film photocatalyst to study the degradation of cephalexin (CPX) as a target pollutant under blue light irradiation. The optical, electrochemical and physicochemical characterization of the as-prepared thin-film samples were carried out by XRD, top-view FE-SEM, EDS-mapping, UV-Vis-DRS, contact angle, EIS, transient photocurrent, mott Schottky and AFM techniques. The rod shape morphology of the samples with moderate surface roughness, desirable hydrophobicity, low bandgap and remarkable band structure alignment confirmed the applicability of as-prepared thin-film with an average photon flux of 1.94 × 10^-4-8.61 × 10^-5 E's m^-2 s^-1. The use of a rotating catalytic disc impressively declined the photon propagation distance, decremented the probability of light absorption by the solution, and intensified the mass transfer rate. The maximum throughputs of 98.8% efficiencies for CPX degradation were achieved at a rotational speed of 180 rpm, the solution flow rate of 1.0 L min^-1, the light intensity of 11 mW cm^-2, and initial CPX concentration of 40 mg L^-1, illumination time of 80 min, and pH of 6. Damkohler number (Da) value was found to be 1.23 × 10^-2 at the optimum conditions, indicating the negligibility of the external mass transfer resistance in the SDPR. The photocatalytic mechanism was elucidated for finding the most operative radical species, suggesting the crucial role of ·O₂^- in photodegradation of CPX and a drastic improvement of the charge separation by S-scheme heterostructure and facilitation by Ag mediator. Findings indicated that the developed reusable and robust SDPR benefited from an s-scheme photocatalyst can be a promising technology for degradation of the organic compounds.

Effect of CuO/ZnO/FTO electrode properties on the performance of a photo-microbial fuel cell sensor for the detection of heavy metals

The development of sustainable, low-cost and responsive technology for heavy metals detection in wastewater is crucial. In this study, by combining CuO/ZnO photocathode with microbial anode, a novel photo-microbial fuel cell (PMFC) sensor was developed. The self-powered PMFC was performed under light and dark condition for heavy metals detection. Compared with MFC sensor, PMFC sensor showed a wider detection range (0.1-4 mg L^-1 of Cd²⁺ and 10-80 mg L^-1 of Cu²⁺). The improved performance in sensing limit and sensitivity was mainly attributed to the intimate P-N heterojunctions formed in CuO/ZnO, which accelerated the electron transport between the photocathode and the microbial anode. Besides, the toxicity of five heavy metals tested in PMFC was shown as Cd²⁺>Cr⁶⁺>Zn²⁺>Hg²⁺>Cu²⁺. This study has taken advantage of the characteristics of PMFC and facilitated its application in heavy metals detection, which provides a new approach for the development of biosensors.

Hybrid of sodium polytungstate polyoxometalate supported by the green substrate for photocatalytic degradation of auramine-O dye

Nowadays, textile industries have severely polluted the ecosystem and water sources via disposal of highly thermo- and photo-stable dyes within the ecology that require practical strategies to remove them from nature. In studies, the photocatalytic disinfection technique has been shown to have widespread applications in indoor air, environmental health, detection, biological, biomedical, laboratory hospital, pharmaceutical food industry, plant safety, waste water, effluents disposal, and drinking water disinfection. Herein, the sodium polytungstate (SPT) polyoxometalate (POM) was synthesized through a multi-step production procedure and hence modified via employing a green protocol by using tartaric acid, glutamic acid, and kombucha solvent toward efficient and total complete removal of the highly toxic, stable, and carcinogenic auramine-O (AO) dye from aqueous media. In this regard, developed materials were well-characterized, and their photocatalysis performance for photodegradation of AO dye was examined. Achieved results showed that the optimum absorption conditions were achieved at pH of 5.0, 15 mg/L of AO concentration, 0.04 g of photocatalyst dosage, and 110 min irradiation time, where SPT and modified SPT via green protocol showed full desirability (desirability function (DF) index of 1) along with 71.75 and 100% removal percentage, respectively. Obtained results justified the superior photocatalytic role of the SPT POM and its derived nanocluster that can be used for the complete removal of highly stable dyes from aqueous media till reaching the drinking water standard.

Synthesis, characterization, and dye degradation photocatalytic activity of the nano-size copper iron binary oxide

Magnetic nano-size copper iron binary oxide is synthesized via a sol-gel method using copper and iron nitrates as precursors and citric acid, chicken egg white, and starch as stabilizers followed by annealing at 400 °C and 800 °C in air. The TG-DTG, XRD, FESEM, EDX, VSM, and FT-IR and UV-Vis DRS spectroscopy methods are used for thermal, structural, magnetic, and optoelectronic characterizations. Depending on the stabilizer and annealing temperature, pure CuFe₂O₄, (CuFe₂O₄,CuO) or (CuFe₂O₄,CuO,Fe₂O₃) phases are formed with nano-size particles of 20-65 nm, having optical band gaps in the range of 2.15-2.60 eV (577-477 nm). Photocatalytic activities of the synthesized nano-size copper iron binary oxide samples are examined for degradation of Nile Blue textile dye displayed first-cycle removal (from water solution) efficiencies of 86.7-93.3%. Considering usage of non-toxic metals and low-cost green stabilizers, good degradation performances, and easy/efficient (magnetic) recyclability, this nano-size catalyst is suggested for further optimization studies for industrial applications.

Fly ash-based nanocomposites: a potential material for effective photocatalytic degradation/elimination of emerging organic pollutants from aqueous stream

Fly ash is readily available and cheaply generated as 47a by-product of the combustion of organic matter. A tremendous amount of fly ash is generated worldwide, and its disposal has imposed 47a severe environmental concern. Its good adsorption capacities attracted several researchers to study the use of fly ash as 47a support for photocatalysts for the degradation of contaminants from wastewater. Undoubtedly the photocatalysts supported on fly ash have represented excellent degradation efficiencies due to the synergistic effect of adsorption and photocatalytic capacity. The utilization of fly ash as 47a precursor has solved the problem of disposal and added value to the waste by-product. Various preparation techniques for fly ash-based nanocomposites such as the sol-gel method, hydrothermal method, solvothermal method, precipitation and co-precipitation, modified metalorganic decomposition, electrospinning, incipient impregnation, and wet chemical synthesis, along with 47a brief study of their characterization using scanning electron microscopy, X-ray diffraction technique and Fourier transform infrared (FTIR) spectroscopy, and the mechanism of photodegradation of dyes have been discussed in this paper. The literature shows that SiO₂, TiO₂, and Al₂O₃ present in fly ash play an essential role in the photodegradation of dyes. Factors affecting the degradation of dyes, their kinetic studies, and methods to enhance photodegradation efficiency have also been discussed.

Nanostructured materials via green sonochemical routes - Sustainability aspects

The production of environmentally friendly nanostructured materials with well-defined properties is a major challenge. Characteristics of the nanomaterials such as dimensionality, size and morphology strongly affect their performance in various applications. Additionally, sustainability considerations require an acceptable level of efficiency while being economically feasible and environmentally benign. The use of ultrasonic irradiation (UI) is a green and powerful technology, which can be applied for the synthesis of a variety of nanostructured materials. This review critically discusses the progress made in the fabrication of environmentally benign engineered nanomaterials with various dimensionalities (i.e., zero, one, two, or three dimensions) assisted by UI. The evolution and current status in this area are further illustrated using a scientometric approach. Application of UI for the synthesis of nanostructured materials has been also assessed according to the main sustainability pillars including the performance and environmental compatibility, as well as the relevant economic and social considerations. The outlook as well as recommendations for future research has been also provided and discussed towards the promotion of sustainable nanomaterials synthesis and application in various fields.

Fabrication and characterization of amidoxime-functionalized silica decorated with copper: a catalytic assembly for rapid reduction of dyes

In this study, amidoxime-functionalized silica decorated with copper (AFS-Cu) was fabricated and tested for its catalytic application. Fourier transform infrared spectroscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy, and X-ray diffraction were employed to characterize its structure and morphology. The application of AFS-Cu as a catalyst for the catalytic reduction of methylene blue (MB) in aqueous media using NaBH₄ as reductant was evaluated. The ability to reuse as well as the effect of catalyst dose and pH of solution on the catalytic activity was investigated. The reduction of MB followed pseudo-first-order kinetics and the rate constant (k) was 0.6224 min^-1. AFS-Cu was found to be a highly effective catalyst for MB reduction reaction and can be easily recovered and reused several times with no appreciable loss of catalytic activity.

Synergetic effect of Sn doped ZnO nanoparticles synthesized via ultrasonication technique and its photocatalytic and antibacterial activity

The current work reports the photocatalytic and antibacterial performance of tin (Sn) doped zinc oxide (ZnO) nanoparticles synthesized via ultrasonic aided co-precipitation technique. The increase of Sn concentration decreased the lattice parameter and increased the crystallite size without changing the ZnO structure. The hexagonal shaped particles and sheets obtained for 3% and 5% Sn substituted ZnO, respectively. The increase of dopant concentration reduced the reflectance and optical band gap energy of Sn doped ZnO. The vibrational band present at 1443 cm^-1 confirmed the successful bond formation of Sn-O-Zn. The 5% Sn doped ZnO nanoparticles exhibited greater dye elimination rate of methylene blue compared to 3% Sn. The antibacterial activity of Sn doped ZnO showed the higher zone of inhibition about 14 mm against different pathogens. The 5% Sn doped ZnO photocatalyst improve the transfer rate of photo excite carrier and decrease the rate of recombination which greatly influence on the photocatalytic and antibacterial performance.

Ce/Eu redox couple functionalized HKUST-1 MOF insight to sono-photodegradation of malathion

The Ce/Eu redox pair-functionalized HKUST-1 MOF, as an innovative environmentally friendly and recyclable sono-photocatalyst, was hydrothermally mixed and fully characterized by XRD, PL, EIS, FE-SEM, EDS, Mott-Schottky, chronoamperometry, and DRS techniques. The obtained chemical and optical characteristics of the n-type Ce/Eu-HKUST-1 MOF showed that the transfer of additional 4f orbital electrons in the Ce/Eu redox pair improves the sono-photocatalytic activity. The performance of Ce/Eu-HKUST-1 MOF for the sono-photodegradation of Malathion (MA) was evaluated in the aqueous media in the simultaneous presence of blue light and ultrasonic irradiation. The optimization of the process was cross-examined using the response surface methodology as a function of the MA concentration (15-35 mg·L^-1), Ce/Eu-HKUST-1 mass (10-30 mg), pH (4-12), and ultrasonic wave irradiation duration (10-30 min). The maximum sono-photocatalytic degradation capacity was found to be 99.99% under the optimum conditions set as 25 mg·L^-1, 20 mg, 8, and 25 min for the concentration of Malathion, photocatalyst mass, pH, and irradiation duration, respectively. These findings were attributed to the suppression of electron-hole pair recombination, increased life-time of charge carriers, enhanced visible light absorption, and prominent proportion of hydroxyl and peroxide radicals formed.

Enhanced photocatalytic performance of Cu2O/MoS2/ZnO composites on Cu mesh substrate for nitrogen reduction

Cu₂O nanoparticles and MoS₂nanoflowers decorated with ZnO nanospheres were successfully co-deposited on Cu mesh via a mild electrodeposition method to build a dual direct Z-scheme heterostructure. The prepared materials can effectively synthesize ammonia with N₂and H₂O in the liquid membrane reactor under simulated visible light. The results indicate that 3D nanomaterials exhibit better performance compared to a pure semiconductor due to the synergistic effect of enhanced visible light absorption, longer photogenerated carrier lifetime and the specific charge transfer path of dual direct Z-scheme structure. Meanwhile, the hydrophilicity of Cu₂O/MoS₂/ZnO rapidly makes the surface of the catalyst wet when it participates in the photo reaction, which promotes the contact between the reactant and exciton. This work proposes the electron transfer and possible reaction mechanism corresponding to the designed catalyst, which can provide a reference for other photocatalytic applications using a semiconductor heterojunction as a catalyst.

Ultrasonic-assisted synthesis of SiO2 nanoparticles and SiO2/chitosan/Fe nanocomposite and their application for vanadium adsorption from aqueous solution

The husk of brown rice, as a source of silica, was applied to synthesize natural SiO₂ nanoparticles via sonochemical method. SiO₂/CH/Fe nanocomposite was synthesized from SiO₂, chitosan (prepared from shrimp shells via sonochemical method), and iron functional groups and detected using BET, EDX-SEM, and FTIR techniques. These natural-based nanostructures (SiO₂ and SiO₂/CH/Fe) have been applied for vanadium adsorption. The influences of initial pH, initial concentration, and adsorption time were studied via a batch process. The analysis of the kinetics data indicated that the chemical adsorption is predominant. The analysis of the equilibrium data indicated the single layer and exothermic adsorption process. The mono-layer adsorption capacity of SiO₂/CH/Fe was 199.540 mg g^-1. The performance of SiO₂/CH/Fe in a continuous column system was investigated in four adsorption and desorption cycles. Results showed that SiO₂/CH/Fe nanocomposite synthesized with the sonochemical method is a candidate with high adsorption ability for use as an industrial adsorbent.

Enhanced cyclic performance initiated via an in situ transformation of Cu/CuO nanodisk to Cu/CuO/Cu2O nanosponge

A simple oxidation method for preparing CuO nanodisks on a flexible Cu sheet is presented. The crystal structure of as-prepared CuO nanodisks was analyzed by X-ray diffraction. The elemental composition and surface morphology were documented by X-ray photoelectron spectroscopy, scanning, and transmission electron microscopy. The photocatalytic performance of flexible Cu/CuO nanodisks was tested to mediate the degradation of RhB and MB dyes. After 2nd recycling, an in situ transformation of the nanodisk surface leads to electron transfer between the conduction bands of Cu₂O and CuO phase, accelerating the degradation of the dyes due to a more favorable electron-hole separation under different band gap engineering. The optical and electrochemical impedance analyses were conducted to examine the efficiency of photogenerated charge carrier separation. Additionally, in the photodegradation system of Cu/CuO nanodisks, the generation of superoxide radical (·O^2-) is responsible for the dye degradation under daylight irradiation. The generation of the latter radical is energetically feasible since the conduction band of Cu₂O (- 0.28 eV) is well-matching with the redox potential of O₂/·O^2- (- 0.28 eV). Consequently, it is concluded that the cyclic stability shows the usefulness of Cu/CuO nanodisk preparation for the dye degradation under daylight irradiation. Graphical abstract.

Sonochemical degradation of bisphenol A using persulfate activated by hematite nanoparticles

In this study, hematite nanoparticles (HNPs) were used as the persulfate (PS) activator for the sonocatalytic degradation of bisphenol A (BPA). The physicochemical properties of the synthesized HNPs were investigated using X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), Fourier transform infrared spectroscopy (FTIR) and transmission electron microscopy (TEM). The effect of different operational parameters (pH, nanoparticle dosage, persulfate concentration, and ultrasonic power) on catalytic activity were evaluated. The BPA degradation rate was improved when ultrasonic (US) irradiation was used simultaneously with HNPs for activating PS. According to the results, 98.94% of BPA (10 mg/L) was degraded within 15 min of reaction time at 4 mM persulfate and 0.01 g/L HNPs under ultrasonic irradiation of 250 W. The degree of mineralization of BPA was measured using chemical oxygen demand (COD), and 36.98% was achieved under optimum conditions. Quenching tests were done using different scavenger compounds; these showed that both hydroxyl and sulfate radicals were reactive species in BPA degradation. According to the results of reusability tests, the degradation efficiency decreased to 86.34%, indicating that HNPs can be recycled several times. All of the anions tested, but mainly hydrogen phosphate, had an inhibitory effect on BPA degradation. The results showed that the US/HNPs/PS process is effective for the degradation of the organic pollutants.

Synthesis and photocatalytic activity of porous ZnO stabilized by TiO2 and Fe3O4 nanoparticles: investigation of pesticide degradation reaction in water treatment

The present research studies the photocatalytic degradation of a pesticide using TiO₂ and Fe₃O₄ nanoparticles supported on ZnO mesoporous (mZnO) substrate. Chlorpyrifos is an organophosphate pesticide with a C₉H₁₁Cl₃NO₃PS chemical formula. It is broadly utilized in agricultural fields to control product pests. The chlorpyrifos toxicity is acute and still dangerous to any aquatic organisms. The mZnO/TiO₂-Fe₃O₄ material was characterized using Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscope (SEM), energy-dispersive X-ray analysis (EDX), transmission electron microscopy (TEM), and N₂ adsorption and desorption (Brunauer-Emmett-Teller; BET). In order to optimize three important operating parameters, i.e., chlorpyrifos concentration, mZnO/TiO₂-Fe₃O₄ nanocomposite amount, and pH, for photocatalytic degradation of chlorpyrifos, response surface methodology (RSM) was applied. The central composite design (CCD) including 20 experiments was used to conduct experiments. The highest photodegradation performance of about 94.8% was obtained for a chlorpyrifos concentration of 8 ppm, a pH of 10, and an amount of mZnO/TiO₂-Fe₃O₄ nanocomposite of 60 mg. The degradation of chlorpyrifos using mZnO/TiO₂-Fe₃O₄ presented good performance (more than 94%). The photocatalytic reaction followed pseudo-first-order kinetics with a rate constant of 0.058 min^-1 for chlorpyrifos degradation. The results propose that mZnO/TiO₂-Fe₃O₄ nanocomposite is a suitable alternative for the degradation of chlorpyrifos in aqueous solution. The improved photocatalytic efficiency could be attributed to the effective separation of electron-hole pairs via a Z-scheme mechanism.