Biodegradable polymers

Cationic waste hemp fibers-based membrane: Case study of anionic pollutants removal through environmentally friendly processes

In this study, waste hemp fibers were transformed into cationically modified lignocellulosic adsorbent through a three-step process. First, a delignification/defibrillation pretreatment was performed, followed by quaternization of fibers using the synthesized ionic liquid chlorocholine chloride-urea (CCC-U). Pressure-assisted cross-linking of modified fibres, using a citric acid, produced new membrane (CCC-UHM). The removal of anionic dyes (Acid Yellow 36 (AY36), Congo Red (CR), Acid Green 25 (AG25), and Acid Blue 92 (AB92)), and oxyanions (As(V) and Cr(VI)) was tested in batch and column system. The structural characteristics and chemical properties of the syntesised materials were investigated by SEM, FTIR, Raman, XPS, XRD, specific density, porosity and point of zero charges analysis. The endothermic and spontaneous equilibration of the system resulted in high capacity (qm), i.e., 302.9 mg g-1 (AY36), 456.8 mg g-1 (CR), 812.8 mg g-1 (AG25), 587.6 mg g-1 (AB92), 107.9 mg g-1 (As(V)), and 67.84 mg g-1 (Cr(VI)) at 25 °C, using the Langmuir model. The optimum pH for the adsorption process was 7. The multi-cycle adsorption/desorption process was followed by either decolorization, using laccase from M. thermophile expressed in Aspergillus oryzae (Novozym 51,003® laccase) immobilized on amino-modified fibers as biocatalyst, or photocatalytic degradation, in the presence of zinc oxide. The high decolorization efficiency (96%) observed for AG25 and AB92 underscores the considerable potential of laccase immobilized preparations as sustainable and eco-friendly approach for treating dye-contaminated wastewater. Photodegradation process provided low environmental threat of processed water, and biodegradabilty of exhausted membrane confirmed the circularity of the developed technology with implemented principles of sustainability.

Accelerated hydrolytic degradation of poly(l-lactide) by blending with poly(ether-block-amide)

A continuing challenge in the most common biodegradable polyester of poly(l-lactide) (PLLA) is to improve the degradation rate in the environment, though it has been widely used in packaging and medical applications. In this study, PLLA/poly(ether-block-amide) (PEBA) blends are prepared by melt blending to investigate the effect of PEBA component on the phase morphology, thermal behavior, mechanical properties, and hydrolytic degradation of the blends. The incorporation of PEBA component is beneficial to the improved toughness and increased water absorption of the blends, and accelerated hydrolytic degradation of PLLA. The blend exhibits the optimal mechanical and hydrolytic degradation properties when the blend mass ratio of PLLA/PEBA is 80/20. The toughness of the blend is increased by 390 % compared to that of pure PLLA. After being hydrolyzed at 58 °C for 240 h, the water absorption, the mass loss and the decrease of molecular weight of the blend is increased by 138 %, 160 % and 40 %, respectively, indicating faster hydrolytic degradation rate of the blend than that of pure PLLA. Furthermore, the accelerated hydrolytic degradation mechanism of PLLA in the blend is revealed. The amorphous region of PLLA is hydrolyzed initially at the phase interface of the blend, and subsequently the crystalline structure of PLLA is degraded. The hydrolysis process causes a change in the relative content of crystalline regions in the system, resulting in an increase in crystallinity of PLLA first and then decrease. These findings provide a new strategy for the design of novel degradable PLLA materials for practical applications.

Biodegradable Natural Hydrogels for Tissue Engineering, Controlled Release, and Soil Remediation

This article provides insights into hydrogels of the most promising biodegradable natural polymers and their mechanisms of degradation, highlighting the different possibilities of controlling hydrogel degradation rates. Since biodegradable hydrogels can be designed as scaffolding materials to mimic the physical and biochemical properties of natural tissues, these hydrogels have found widespread application in the field of tissue engineering and controlled release. In the same manner, their potential as water reservoirs, macro- and microelement carriers, or matrixes for the selective adsorption of pollutants make them excellent candidates for sustainable soil amendment solutions. Accordingly, this article summarizes the recent advances in natural biodegradable hydrogels in the fields of tissue engineering, controlled release, and soil remediation, emphasizing the new opportunities that degradability and its tunability offer for the design and applicability of hydrogels.

Current Challenges in Microcapsule Designs and Microencapsulation Processes: A Review

Microencapsulation is an advanced methodology for the protection, preservation, and/or delivery of active materials in a wide range of industrial sectors, such as pharmaceuticals, cosmetics, fragrances, paints, coatings, detergents, food products, and agrochemicals. Polymeric materials have been extensively used as microcapsule shells to provide appropriate barrier properties to achieve controlled release of the encapsulated active ingredient. However, significant limitations are associated with such capsules, including undesired leaching and the nonbiodegradable nature of the typically used polymers. In addition, the energy cost of manufacturing microcapsules is an important factor to be considered when designing microcapsule systems and the corresponding production processes. Recent factors linked to UN sustainability goals are modifying how such microencapsulation systems should be designed in pursuit of "ideal" microcapsules that are efficient, safe, cost-effective and environmentally friendly. This review provides an overview of advances in microencapsulation, with emphasis on sustainable microcapsule designs. The key evaluation techniques to assess the biodegradability of microcapsules, in compliance with recently evolving European Union requirements, are also described. Moreover, the most common methodologies for the fabrication of microcapsules are presented within the framework of their energy demand. Recent promising microcapsule designs are also highlighted for their suitability toward meeting current design requirements and stringent regulations, tackling the ongoing challenges, limitations, and opportunities.

Novel DNA-Binding Activity Exhibited by Poly(aspartic acid) Hydrolase-1 Inhibits Poly(aspartic acid) Hydrolase Activity

Significant attention has been shifted toward the use and development of biodegradable polymeric materials to mitigate environmental accumulation and potential health impacts. One such material, poly(aspartic acid) (PAA), is a biodegradable alternative to superabsorbent poly(carboxylates), like poly(acrylate). Three enzymes are known to hydrolyze PAA: PahZ1KT-1 and PahZ2KT-1 from Sphingomonas sp. KT-1 and PahZ1KP-2 from Pedobacter sp. KP-2. We previously reported the X-ray crystal structure for PahZ1KT-1, which revealed a homodimer complex with a strongly cationic surface spanning one side of each monomer. Here, we report the first characterization of any polymer hydrolase binding to DNA, where modeling data predict binding of the polyanionic DNA near the cationic substrate binding surface. Our data reveal that PahZ1 homologues from Sphingomonas sp. KT-1 and Pedobacter sp. KP-2 bind ssDNA and dsDNA with nanomolar binding affinities. PahZ1KT-1 binds ssDNA and dsDNA with an apparent dissociation constant, KD,app = 81 ± 14 and 19 ± 1 nM, respectively, and these estimates are similar to the same behaviors exhibited by PahZ1KP-2. Gel permeation chromatography data reveal that dsDNA binding promotes inhibition of PahZ1-catalyzed PAA biodegradation for each homologue. We propose a working model wherein binding of PahZ1 to extracellular biofilm DNA aids in the localization of the hydrolase to the environment in which PAA would first be encountered, thereby providing a mechanism to degrade extracellular PAA and potentially harvest aspartic acid for nutritional uptake.

PBAT is biodegradable but what about the toxicity of its biodegradation products?

CONTEXT

Poly(butylene adipate-co-terephthalate) (PBAT) is a biodegradable plastic. It was introduced to the plastics market in 1998 and since then has been widely used around the world. The main idea of this research is to perform quantum chemical calculations to study the potential toxicity of PBAT and its degradation products. We analyzed the electron transfer capacity to determine its potential toxicity. We found that biodegradable products formed with benzene rings are as good electron acceptors as PBAT and OOH•. Our results indicate that the biodegradation products are potentially as toxic as PBAT. This might explain why biodegradation products alter the photosynthetic system of plants and inhibit their growth. From this and other previous investigations, we can think that biodegradable plastics could represent a potential environmental risk.

METHODS

All DFT computations were performed using the Gaussian16 at M062x/6-311 + g(2d,p) level of theory without symmetry constraints. Electro-donating (ω-) and electro-accepting (ω +) powers were used as response functions.

Degradable and Recyclable Hydrogels for Sustainable Bioelectronics

Hydrogel bioelectronics has been widely used in wearable sensors, electronic skin, human-machine interfaces, and implantable tissue-electrode interfaces, providing great convenience for human health, safety, and education. The generation of electronic waste from bioelectronic devices jeopardizes human health and the natural environment. The development of degradable and recyclable hydrogels is recognized as a paradigm for realizing the next generation of environmentally friendly and sustainable bioelectronics. This review first summarizes the wide range of applications for bioelectronics, including wearable and implantable devices. Then, the employment of natural and synthetic polymers in hydrogel bioelectronics is discussed in terms of degradability and recyclability. Finally, this work provides constructive thoughts and perspectives on the current challenges toward hydrogel bioelectronics, providing valuable insights and guidance for the future evolution of sustainable hydrogel bioelectronics.

Environmental impact of microplastics and potential health hazards

Microscopic plastic (microplastic) pollutants threaten the earth's biodiversity and ecosystems. As a result of the progressive fragmentation of oversized plastic containers and products or manufacturing in small sizes, microplastics (particles of a diameter of 5 mm with no lower limit) are used in medicines, personal care products, and industry. The incidence of microplastics is found everywhere in the air, marine waters, land, and even food that humans and animals consume. One of the greatest concerns is the permanent damage that is created by plastic waste to our fragile ecosystem. The impossibility of the complete removal of all microplastic contamination from the oceans is one of the principal tasks of our governing body, research scientists, and individuals. Implementing the necessary measures to reduce the levels of plastic consumption is the only way to protect our environment. Cutting off the plastic flow is the key remedy to reducing waste and pollution, and such an approach could show immense significance. This review offers a comprehensive exploration of the various aspects of microplastics, encompassing their composition, types, properties, origins, health risks, and environmental impacts. Furthermore, it delves into strategies for comprehending the dynamics of microplastics within oceanic ecosystems, with a focus on averting their integration into every tier of the food chain.

Analyzing Mushroom Structural Patterns of a Highly Compressible and Expandable Hemostatic Foam for Gastric Perforation Repair

Nature presents the most beautiful patterns through evolving. Here, a layered porous pattern in golden ratio (0.618) is reported from a type of mushroom -Dictyophora Rubrovalvata stipe (DRS). The hierarchical structure shows a mathematical correlation with the golden ratio. This unique structure leads to superior mechanical properties. The gradient porous structure from outside to innermost endows it with asymmetrical hydrophilicity. A mathematical model is then developed to predict and apply to 3D printed structures. The mushroom is then explored to repair gastric perforation because the stomach is a continuous peristaltic organ, and the perforated site is subject to repeated mechanical movements and pressure changes. At present, endoscopic clipping is ineffective in treating ulcerative perforation with fragile surrounding tissues. Although endoscopic implant occlusion provides a new direction for the treatment of gastric ulcers, but the metal or plastic occluder needs to be removed, requiring a second intervention. Decellularized DRS (DDRS) is found with asymmetric water absorption rate, super-compressive elasticity, shape memory, and biocompatibility, making it a suitable occluder for the gastric perforation. The efficacy in blocking gastric perforation and promoting healing is confirmed by endoscopic observation and tissue analysis during a 2-month study.

How Biodegradable Polymers Can be Effective Drug Delivery Systems for Cannabinoids? Prospectives and Challenges

Cannabinoids are compounds found in and derived from the Cannabis plants that have become increasingly recognised as significant modulating factors of physiological mechanisms and inflammatory reactions of the organism, thus inevitably affecting maintenance of homeostasis. Medical Cannabis popularity has surged since its legal regulation growing around the world. Numerous promising discoveries bring more data on cannabinoids' pharmacological characteristics and therapeutic applications. Given the current surge in interest in the medical use of cannabinoids, there is an urgent need for an effective method of their administration. Surpassing low bioavailability, low water solubility, and instability became an important milestone in the advancement of cannabinoids in pharmaceutical applications. The numerous uses of cannabinoids in clinical practice remain restricted by limited administration alternatives, but there is hope when biodegradable polymers are taken into account. The primary objective of this review is to highlight the wide range of indications for which cannabinoids may be used, as well as the polymeric carriers that enhance their effectiveness. The current review described a wide range of therapeutic applications of cannabinoids, including pain management, neurological and sleep disorders, anxiety, and cancer treatment. The use of these compounds was further examined in the area of dermatology and cosmetology. Finally, with the use of biodegradable polymer-based drug delivery systems (DDSs), it was demonstrated that cannabinoids can be delivered specifically to the intended site while also improving the drug's physicochemical properties, emphasizing their utility. Nevertheless, additional clinical trials on novel cannabinoids' formulations are required, as their full spectrum therapeutical potential is yet to be unravelled.

Influence of microbial biomass content on biodegradation and mechanical properties of poly(3-hydroxybutyrate) composites

Biodegradation rates and mechanical properties of poly(3-hydroxybutyrate) (PHB) composites with green algae and cyanobacteria were investigated for the first time. To the authors knowledge, the addition of microbial biomass led to the biggest observed effect on biodegradation so far. The composites with microbial biomass showed an acceleration of the biodegradation rate and a higher cumulative biodegradation within 132 days compared to PHB or the biomass alone. In order to determine the causes for the faster biodegradation, the molecular weight, the crystallinity, the water uptake, the microbial biomass composition and scanning electron microscope images were assessed. The molecular weight of the PHB in the composites was lower than that of pure PHB while the crystallinity and microbial biomass composition were the same for all samples. A direct correlation of water uptake and crystallinity with biodegradation rate could not be observed. While the degradation of molecular weight of PHB during sample preparation contributed to the improvement of biodegradation, the main reason was attributed to biostimulation by the added biomass. The resulting enhancement of the biodegradation rate appears to be unique in the field of polymer biodegradation. The tensile strength was lowered, elongation at break remained constant and Young's modulus was increased compared to pure PHB.

Upcycling Low-Quality Cotton Fibers into Mulch Gel Films in a Fast Closed Carbon Cycle

Low-quality cotton fibers, often overlooked as low-value materials, constitute a marginalized waste stream in the cotton industry. This study endeavored to repurpose these fibers into mulch gel films, specifically exploring their efficacy in covering moisture-controlled soil beds. Through a meticulously designed series of processing methods, cellulose/glycerol film was successfully fabricated by regenerating cellulose hydrogels in N,N-dimethylacetamide/lithium chloride solutions, followed by plasticization in glycerol/water solutions and hot pressing. The film was then employed to cover soil beds for a duration of up to 252 days, followed by soil burial assessments. Despite expectations of degradation, the film maintained structural integrity throughout the soil covering period but underwent complete biodegradation after 80 days of soil burial, thereby completing a closed carbon cycle. Intriguingly, both tensile strength and modulus exhibited no diminishment but instead increased after soil covering, contrary to expectations given the usual role of degradation. Mechanistic insights revealed that the removal of glycerol contributed to the mechanical enhancement, while microbial activity predominately decomposed the amorphous regions in soil covering and targeted the crystalline portions in soil burial, elucidating the main biodegradation mechanisms. In summary, this study presents, for the first time, the potential of upcycling low-quality cotton fibers into high-value mulch gel films for agricultural practices within a closed carbon cycle.

Ring Opening Polymerization of Six- and Eight-Membered Racemic Cyclic Esters for Biodegradable Materials

The low percentage of recyclability of the polymeric materials obtained by olefin transition metal (TM) polymerization catalysis has increased the interest in their substitution with more eco-friendly materials with reliable physical and mechanical properties. Among the variety of known biodegradable polymers, linear aliphatic polyesters produced by ring-opening polymerization (ROP) of cyclic esters occupy a prominent position. The polymer properties are highly dependent on the macromolecule microstructure, and the control of stereoselectivity is necessary for providing materials with precise and finely tuned properties. In this review, we aim to outline the main synthetic routes, the physical properties and also the applications of three commercially available biodegradable materials: Polylactic acid (PLA), Poly(Lactic-co-Glycolic Acid) (PLGA), and Poly(3-hydroxybutyrate) (P3HB), all of three easily accessible via ROP. In this framework, understanding the origin of enantioselectivity and the factors that determine it is then crucial for the development of materials with suitable thermal and mechanical properties.

Polymer Delivery Systems for Long-Acting Antiretroviral Drugs

The success of long-acting (LA) drug delivery systems (DDSs) is linked to their biocompatible polymers. These are used for extended therapeutic release. For treatment or prevention of human immune deficiency virus type one (HIV-1) infection, LA DDSs hold promise for improved regimen adherence and reduced toxicities. Current examples include Cabenuva, Apretude, and Sunlenca. Each is safe and effective. Alternative promising DDSs include implants, prodrugs, vaginal rings, and microarray patches. Each can further meet patients' needs. We posit that the physicochemical properties of the formulation chemical design can optimize drug release profiles. We posit that the strategic design of LA DDS polymers will further improve controlled drug release to simplify dosing schedules and improve regimen adherence.

UV Light Degradation of Polylactic Acid Kickstarts Enzymatic Hydrolysis

Polylactic acid (PLA) and bioplastics alike have a designed degradability to avoid the environmental buildup that petroplastics have created. Yet, this designed biotic-degradation has typically been characterized in ideal conditions. This study seeks to relate the abiotic to the biotic degradation of PLA to accurately represent the degradation pathways bioplastics will encounter, supposing their improper disposal in the environment. Enzymatic hydrolysis was used to study the biodegradation of PLA with varying stages of photoaging. Utilizing a fluorescent tag to follow enzyme hydrolysis, it was determined that increasing the amount of irradiation yielded greater amounts of total enzymatic hydrolysis by proteinase K after 8 h of enzyme incubation. While photoaging of the polymers causes minimal changes in chemistry and increasing amounts of crystallinity, the trends in biotic degradation appear to primarily be driven by photoinduced reduction in molecular weight. The relationship between photoaging and enzyme hydrolysis appears to be independent of enzyme type, though commercial product degradation may be impacted by the presence of additives. Overall, this work reveals the importance of characterizing biodegradation with relevant samples that ultimately can inform optimization of production and disposal.

Impact of ultrasound treatment on the structural modifications and functionality of carbohydrates - A review

Carbohydrates are crucial in food as essential biomolecules, serving as natural components, ingredients, or additives. Carbohydrates have numerous applications in the food industry as stabilizers, thickeners, sweeteners, and humectants. The properties and functionality of the carbohydrates undergo alterations when exposed to various thermal or non-thermal treatments. Ultrasonication is a non-thermal method that modifies the structural arrangement of carbohydrate molecules. These structural changes lead to enhanced gelling and viscous nature of the carbohydrates, thus enhancing their scope of application. Ultrasound may improve carbohydrate functionality in an environmentally sustainable way, leaving no chemical residues. The high-energy ultrasound treatments significantly reduce the molecular size of complex carbohydrates. Sonication parameters like treatment intensity, duration of treatment, and energy applied significantly affect the molecular size, depolymerization, viscosity, structural modifications, and functionality of carbohydrate biomolecules. This review provides a comprehensive analysis of ultrasound-assisted modifications in carbohydrates and the changes in functional properties induced by sonication.

Biomedical applications of electrospun polycaprolactone-based carbohydrate polymers: A review

Carbohydrate used in biomedical applications is influenced by numerous factors. One of the most appealing characteristic of carbohydrates is their ability to reproduce from natural resources which makes them ecologically friendly. Due to their abundance, biocompatibility, and no contamination by residual initiators, the desire for polysaccharides in medical uses is growing. Research on fiber-based materials, with a variety of medical applications including bio-functional scaffolds, continues to yield novel and intriguing findings. Almost all biopolymers of diverse structural compositions are electrospun to fulfill biomedical usage criteria, and the electrospinning technique is widely employed in biomedical technologies for both in-vivo and in-vitro therapies. Due to its biocompatibility and biodegradability, polycaprolactone (PCL) is employed in medical applications like tissue engineering and drug delivery. Although PCL nanofibers have established effects in vitro, more research is needed before their potential therapeutic application in the clinic. Here we tried to focus mainly on the carbohydrate incorporated PCL-based nanofibers production techniques, structures, morphology, and physicochemical properties along with their usage in biomedicine.

Chewing gum base: A comprehensive review of composition, production, and assessment methods: Advances and approaches in biodegradability

The gum base mass is a colloidal system and the main component of chewing gum; which is an inert, non-nutritious, indigestible, and insoluble part of chewing gum, therefore this substance does not dissolve in the mouth when chewed. The gum base plays the most crucial role in determining the mechanical properties, flexibility, and overall quality of chewing gum. Moreover, it acts as a delivery system to transport sweeteners, flavorings, and other ingredients in chewing gum. Despite the massive market for chewing gum and the provision of a list of the main ingredients in gum base by the Code of Federal Regulations and some international organizations, there is a lack of information about chewing gum base and its compositions in the literature. Therefore, the purpose of this review is to present an overview of the characteristics, ingredients and applications, production process, assessment, and modification methods of the gum base along with the advances and approaches in biodegradability. Biodegradability concerns play a promoting role in the research and development of chewing gum and its applications in the food industry, medical and dental sectors. Reviewing previous studies can surely help for faster development of this path.

Polysaccharides and proteins based bionanocomposites as smart packaging materials: From fabrication to food packaging applications a review

Food industry is the biggest and rapidly growing industries all over the world. This sector consumes around 40 % of the total plastic produced worldwide as packaging material. The conventional packaging material is mainly petrochemical based. However, these petrochemical based materials impose serious concerns towards environment after its disposal as they are nondegradable. Thus, in search of an appropriate replacement for conventional plastics, biopolymers such as polysaccharides (starch, cellulose, chitosan, natural gums, etc.), proteins (gelatin, collagen, soy protein, etc.), and fatty acids find as an option but again limited by its inherent properties. Attention on the initiatives towards the development of more sustainable, useful, and biodegradable packaging materials, leading the way towards a new and revolutionary green era in the food sector. Eco-friendly packaging materials are now growing dramatically, at a pace of about 10-20 % annually. The recombination of biopolymers and nanomaterials through intercalation composite technology at the nanoscale demonstrated some mesmerizing characteristics pertaining to both biopolymer and nanomaterials such as rigidity, thermal stability, sensing and bioactive property inherent to nanomaterials as well as biopolymers properties such as flexibility, processability and biodegradability. The dramatic increase of scientific research in the last one decade in the area of bionanocomposites in food packaging had reflected its potential as a much-required and important alternative to conventional petroleum-based material. This review presents a comprehensive overview on the importance and recent advances in the field of bionanocomposite and its application in food packaging. Different methods for the fabrication of bionanocomposite are also discussed briefly. Finally, a clear perspective and future prospects of bionanocomposites in food packaging were presented.

Tuning the Emulsion Properties Influences the Size of Poly(Caprolactone) Particles for Drug Delivery Applications

Advances in drug delivery have been accelerated with the addition of polymeric drug carriers. Direct delivery to a target site is a promising step in developing effective drug and gene therapies to treat disease. The efficacy of these drug carriers heavily relies on cell uptake without compromising critical cellular processes that promote cell viability. Drug release from biodegradable polymers is mediated largely by polymer degradation, and therefore the rate of polymer degradation dictates the feasibility of drug delivery applications. Traditionally, poly(caprolactone) (PCL) has only been used in long-term biomedical applications because the degradation time is much slower than other polymers. However, the biocompatibility of this polymer and the potential for longer delivery windows renders it a promising polymer candidate for drug delivery. In this work, we outline sixteen emulsion solvent evaporation preparation methods for PCL nanoparticles and microparticles to develop particles between 300 nm and 1.7 μm and with zeta potentials of -1.8 mV. We further investigated particles in a size range suitable for systemic tumor delivery and inhaled aerosol delivery to determine cell biocompatibility with the polymer in lung adenocarcinoma, endometrial adenocarcinoma, and human embryonic kidney cells. We determined these particles aren't detrimental to cell viability below particle monolayer coverage atop cells and therefore these formulations hold promise for the next stage of development as sustained-release drug delivery carriers.

On the evaluation of the carbon dioxide solubility in polymers using gene expression programming

Evaluation, prediction, and measurement of carbon dioxide (CO2) solubility in different polymers are crucial for engineers in various chemical applications, such as extraction and generation of novel materials. In this paper, correlations based on gene expression programming (GEP) were generated to predict the value of carbon dioxide solubility in three polymers. Results showed that the generated correlations could represent an outstanding efficiency and provide predictions for carbon dioxide solubility with satisfactory average absolute relative errors of 9.71%, 5.87%, and 1.63% for polystyrene (PS), polybutylene succinate-co-adipate (PBSA), and polybutylene succinate (PBS), respectively. Trend analysis based on Henry's law illustrated that increasing pressure and decreasing temperature lead to an increase in carbon dioxide solubility. Finally, outlier discovery was applied using the leverage approach to detect the suspected data points. The outlier detection demonstrated the statistical validity of the developed correlations. William's plot of three generated correlations showed that all of the data points are located in the valid zone except one point for PBS polymer and three points for PS polymer.

Going beyond Cellulose and Chitosan: Synthetic Biodegradable Membranes for Drinking Water, Wastewater, and Oil-Water Remediation

Membrane technology is an efficient way to purify water, but it generates non-biodegradable biohazardous waste. This waste ends up in landfills, incinerators, or microplastics, threatening the environment. To address this, research is being conducted to develop compostable alternatives that are sustainable and ecofriendly. Bioplastics, which are expected to capture 40% of the market share by 2030, represent one such alternative. This review examines the feasibility of using synthetic biodegradable materials beyond cellulose and chitosan for water treatment, considering cost, carbon footprint, and stability in mechanical, thermal, and chemical environments. Although biodegradable membranes have the potential to close the recycling loop, challenges such as brittleness and water stability limit their use in membrane applications. The review suggests approaches to tackle these issues and highlights recent advances in the field of biodegradable membranes for water purification. The end-of-life perspective of these materials is also discussed, as their recyclability and compostability are critical factors in reducing the environmental impact of membrane technology. This review underscores the need to develop sustainable alternatives to conventional membrane materials and suggests that biodegradable membranes have great potential to address this challenge.

A comprehensive review on polylactic acid (PLA) - Synthesis, processing and application in food packaging

Plastics play an essential role in food packaging; their primary function is to preserve the nature of the food, ensure adequate shelf life and ensure food safety. Plastics are being produced on a global scale in excess of 320 million tonnes annually, with demand rising to reflect the material in wide range of applications. Nowadays, the packaging industry is a significant consumer of synthetic plastic made from fossil fuels. Petrochemical-based plastics are regarded as the preferred material for packaging. Nonetheless, using these plastics in large quantities results in a long-standing environment. Environmental pollution and the depletion of fossil fuels have prompted researchers and manufacturers to develop eco-friendly biodegradable polymers to replace petrochemical-based polymers. As a result, the production of eco-friendly food packaging material has sparked increased interest as a viable alternative to petrochemical-based polymers. Polylactic acid (PLA) is one of the compostable thermoplastic biopolymers that is biodegradable and renewable in nature. High-molecular-weight PLA can be used to produce fibres, flexible, non-wovens, hard and durable materials (100,000 Da or even higher).The chapter focuses on food packaging techniques, food industry waste, biopolymers, their classification, PLA synthesis, the importance of PLA properties for food packaging, and technologies used to process PLA in food packaging.

A Versatile Step-Growth Polymerization Route to Functional Polyesters from an Activated Diester Monomer

This work describes a versatile and efficient condensation polymerization route to aliphatic polyesters by organo-catalyzed (4-dimethylaminopyridine) transesterification reactions between an activated pentafluorophenyl-diester of adipic acid and structurally different diols. By introducing "monofunctional impurity" or "stoichiometric imbalance," this methodology can afford well-defined end-functionalized polyesters with predictable molecular weights and narrow dispersity under mild conditions without any necessity for the removal of the byproducts to accelerate the polymerization reaction, which remains a major challenge in conventional polyester synthesis with non-activated diesters. Wide substrate scope with structurally different monomers and the synthesis of block copolymers by chain extension following either ring-opening polymerization or controlled radical polymerization have been successfully demonstrated. Some of the polyesters synthesized by this newly introduced approach show high thermal stability, crystallinity, and enzymatic degradation in aqueous environments.

Controlled degradation of polycaprolactone-based micropillar arrays

Herein we demonstrate the fabrication of arrays of micropillars, achieved through the combination of direct laser writing and nanoimprint lithography. By combining two diacrylate monomers, polycaprolactone dimethacrylate (PCLDMA) and 1,6-hexanediol diacrylate (HDDA), two copolymer formulations that, owing to the varying ratios of the hydrolysable ester functionalities present in the polycaprolactone moiety, can be degraded in the presence of base in a controllable manner. As such, the degradation of the micropillars can be tuned over several days as a function of PCLDMA concentration within the copolymer formulations, and the topography greatly varied over a short space of time, as visualised using scanning electron microscopy and atomic force microscopy. Crosslinked neat HDDA was used as a control material, demonstrating that the presence of the PCL was responsible for the ability of the microstructures to degrade in the controlled manner. In addition, the mass loss of the crosslinked materials was minimal, demonstrating the degradation of microstructured surfaces without loss of bulk properties was possible. Moreover, the compatibility of these crosslinked materials with mammalian cells was explored. The influence of both indirect and direct contact of the materials with A549 cells was assessed by profiling indices reflective of cytotoxicity such as morphology, adhesion, metabolic activity, oxidative balance, and release of injury markers. No significant changes in the aforementioned profile were observed in the cells cultured under these conditions for up to 72 h, with the cell-material interaction suggesting these materials may have potential in microfabrication contexts towards biomedical application purposes.

Impacts of nano/micro-plastics on safety and quality of aquatic food products

The spread of nano/microplastics (N/MPs) pollution has gained importance due to the associated health concerns. Marine environment including fishes, mussels, seaweed and crustaceans are largely exposed to these potential threats. N/MPs are associated with plastic, additives, contaminants and microbial growth, which are transmitted to higher trophic levels. Foods from aquatic origin are known to promote health and have gained immense importance. Recently, aquatic foods are traced to transmit the nano/microplastic and the persistent organic pollutant poising hazard to humans. However, microplastic ingestion, translocation and bioaccumulation of the contaminant have impacts on animal health. The level of pollution depends upon the pollution in the zone of growth for aquatic organisms. Consumption of contaminated aquatic food affects the health by transferring the microplastic and chemicals. This chapter describes the sources and occurrence of N/MPs in marine environment, detailed classification of N/MPs based on the properties influencing associated hazard. Additionally, occurrence of N/MPs and their impact on quality and safety in aquatic food products are discussed. Lastly, existing regulations and requirements of a robust framework of N/MPs are reviewed.

Exploitation of bacterial strains for microplastics (LDPE) biodegradation

Plastic waste (microplastics) is one of the primary sources of environmental pollutants, serving as a reservoir for them. In this study, previously isolated and screened polymer-degrading bacteria (B. subtilis V8, P. aminophilusB1 4-, P. putida C 2 5, P. aeruginosa V1, and A. calcoaceticus V4) were utilised to examine the biodegradation of LDPE (low-density polyethylene) microplastics. Response surface methodology (RSM) was used to optimize the physicochemical growth parameters (pH, temperature, and ammonium sulphate concentration). By using the polyphasic approach, including CO₂ estimation, weight loss analysis, scanning electron microscopy (SEM), fourier transform infrared (FT-IR) spectroscopy, and electrical conductivities examine the plastic biodegradability. After four months, all biodegradable plastic samples were evaluated. When compared to the other tested cultures, P. aeruginosa V1 showed the most significant degradation (CO₂evolution of 8.86 g.l^-l and percentage weight loss of 18.21 %) with increased electrical conductivity, followed by B. subtilis V8 (CO₂ evolution of 8.10 g.l^-l and percentage weight loss of 16.12 %), A. calcoaceticus V4 (CO₂ evolution of 7.21 g.l^-l and percentage weight loss of 15.44 %), P. putida C 2-5 (CO₂ evolution of 5.76 g.l^-l and percentage weight loss of 13.30 %), and P. aminophilus B1 4- (CO₂ evolution of 5.62 g.l^-l and percentage weight loss of 11.72 %). The deteriorated materials' exterior modifications (surface alteration) were also examined using SEM analysis, and the chemical bonding alterations (bond vibration-bending) were determined using FT-IR spectroscopy.

Polymer-Degrading Enzymes of Pseudomonas chloroaphis PA23 Display Broad Substrate Preferences

Although many bacterial lipases and PHA depolymerases have been identified, cloned, and characterized, there is very little information on the potential application of lipases and PHA depolymerases, especially intracellular enzymes, for the degradation of polyester polymers/plastics. We identified genes encoding an intracellular lipase (LIP3), an extracellular lipase (LIP4), and an intracellular PHA depolymerase (PhaZ) in the genome of the bacterium Pseudomonas chlororaphis PA23. We cloned these genes into Escherichia coli and then expressed, purified, and characterized the biochemistry and substrate preferences of the enzymes they encode. Our data suggest that the LIP3, LIP4, and PhaZ enzymes differ significantly in their biochemical and biophysical properties, structural-folding characteristics, and the absence or presence of a lid domain. Despite their different properties, the enzymes exhibited broad substrate specificity and were able to hydrolyze both short- and medium-chain length polyhydroxyalkanoates (PHAs), para-nitrophenyl (pNP) alkanoates, and polylactic acid (PLA). Gel Permeation Chromatography (GPC) analyses of the polymers treated with LIP3, LIP4, and PhaZ revealed significant degradation of both the biodegradable as well as the synthetic polymers poly(ε-caprolactone) (PCL) and polyethylene succinate (PES).

Nanostrategies for Therapeutic and Diagnostic Targeting of Gastrin-Releasing Peptide Receptor

Advances in nanomedicine bring the attention of researchers to the molecular targets that can play a major role in the development of novel therapeutic and diagnostic modalities for cancer management. The choice of a proper molecular target can decide the efficacy of the treatment and endorse the personalized medicine approach. Gastrin-releasing peptide receptor (GRPR) is a G-protein-coupled membrane receptor, well known to be overexpressed in numerous malignancies including pancreatic, prostate, breast, lung, colon, cervical, and gastrointestinal cancers. Therefore, many research groups express a deep interest in targeting GRPR with their nanoformulations. A broad spectrum of the GRPR ligands has been described in the literature, which allows tuning of the properties of the final formulation, particularly in the field of the ligand affinity to the receptor and internalization possibilities. Hereby, the recent advances in the field of applications of various nanoplatforms that are able to reach the GRPR-expressing cells are reviewed.

A review of environmental friendly green composites: production methods, current progresses, and challenges

The growing concern about environmental damage and the inability to meet the demand for more versatile, environmentally friendly materials has sparked increasing interest in polymer composites derived from renewable and biodegradable plant-based materials, mainly from forests. These composites are mostly referred to as "green" and they can be widely employed in many industrial applications. Green composites are less harmful to the environment and could be potential substitutes for petroleum-based polymeric materials. It is helpful to limit usage of fossil oil assets by developing biopolymer matrices such as cellulose-reinforced biocomposites using renewable assets such as plant oils, carbohydrates, and proteins. This paper focuses on green composites processing utilizing a variety of naturally available resources, sustainable materials which are not detrimental to the environment, new scientific signs of progress in achieving green sustainable development, as well as nanotechnology and its environmental consequences. Additionally, the environmental impacts of different composite materials are examined in this paper, along with their production from eco-friendly materials. Moreover, the manufacturing aspects of green composites and some concerns related to their production are also discussed. The merits of green composite materials and valid reasons why they are a valuable substitute for the traditionally used composite materials are also covered.

Piperine-loaded nanoparticles incorporated into hyaluronic acid/sodium alginate-based membranes for the treatment of inflammatory skin diseases

Piperine is an alkaloid mostly found in the fruits of several species of the Piper genus, and its anti-inflammatory potential is already known. However, its therapeutic applications still need to be better explored due to the low aqueous solubility of this active. To overcome this drawback, the objective of this work was to evaluate the efficiency of the nanoencapsulation of the compound as well as its incorporation into hyaluronic acid/alginate-based biomembranes. Polymeric nanoparticles composed of Eudragit S100 and Poloxamer 188 were obtained by the nanoprecipitation technique, obtaining spherical nanosized particles with an average diameter of 122.1 ± 2.0 nm, polydispersity index of 0.266, and encapsulation efficiency of 76.2 %. Hyaluronic acid/sodium alginate membranes were then prepared and characterized. Regarding permeation, a slow passage rate was observed until the initial 14 h, when an exponential increase in the recovered drug concentration began to occur. The in vivo assay showed a reduction in inflammation up to 43.6 %, and no cytotoxicity was observed. The results suggested the potential of the system developed for the treatment of inflammatory skin diseases.

Characterization of Biodegradable Food Contact Materials under Gamma-Radiation Treatment

Radiation is an example of one of the techniques used for pasteurization and sterilization in various packaging systems. There is a high demand for the evaluation of the possible degradation of new composites, especially based on natural raw materials. The results of experimental research that evaluated the impact of radiation technology on biodegradable and compostable packaging materials up to 40 kGy have been presented. Two commercially available flexible composite films based on aliphatic-aromatic copolyesters (AA) were selected for the study, including one film with chitosan and starch (AA-CH-S) and the other with thermoplastic starch (AA-S). The materials were subjected to the influence of ionizing radiation from 10 to 40 kGy and then tests were carried out to check their usability as packaging material for the food industry. The results showed that the mechanical properties of AA-S films improved due to the radiation-induced cross-linking processes, while in the case of AA-CH-S films, a considerable decrease in the elongation at break was observed. The results also showed a decrease in the WVTR in the case of AA-S and no changes in barrier properties in the case of AA-CH-S. Both materials revealed no changes in the odor analyzed by sensory analysis. In the case of the AA-S films, the higher the radiation dose, the faster the biodegradation rate. In the case of the AA-CH-S film, the radiation did not affect biodegradation. The performed research enables the evaluation of the materials intended for direct contact with food. AA-CH-S was associated with unsatisfactory parameters (exceeding the overall migration limit and revealing color change during storage) while AA-S showed compliance at the level of tests carried out. The study showed that the AA-CH-S composite did not show a synergistic effect due to the presence of chitosan.

Studies on the morphology, phylogeny, and bioremediation potential of Penicillium citrinum and Paecilomyces variotii (Eurotiales) from oil-contaminated areas

Crude oil pollution is one of the most arduous issues to address, as it is hazardous to both public health and the environment. The discovery of novel biosurfactants-producing fungi and bacteria is in high demand due to their excellent properties and wide range of applications. The aim of this research is to isolate a powerful biosurfactant-producing fungus from the crude oil site near Barauni oil refinery in Bihar, India. Standard protocols were used to collect samples from the site. An integrative taxonomic approach was used, which included morphological, molecular, and phylogenetic analysis. The use of plating samples on Bushnell-Hass (BH) media aided in the isolation of a fungal strain from an enrichment culture. Two fungal strains isolated from contaminated soils, Penicillium citrinum and Paecilomyces variotti, showed potent oil degrading activity in a single culture. For preliminary biosurfactants screening, drop collapse assays, oil spreading, and emulsification activity tests were used. The results showed that the cultures performed well in the screening test and were further evaluated for degradation capacity. Different treatment periods (0, 3, 6, 9, 12, and 15 days) were used to observe degradation in single cultures. A steady drop in pH, an alteration in optical density and an increase in carbon dioxide release showed the ability of fungal strain to degrade the crude oil in a single culture. Fungi mycelia provide a larger surface area for absorption and degradation of the pollutants in contaminated environment. They produce extracellular enzymes to degrade the oil, and at the same time absorb and utilise carbon, allowing them to remove toxic substances from the oil. Thus, they could be candidates for bioremediation of a hydrocarbon-contaminated site.

Knowledge and awareness of polycaprolactone and its applications as provisional material in prosthodontic practice: A questionnaire-based survey

Aim

The present study was done to evaluate the knowledge and awareness of different provisional materials, especially polycaprolactone (PCL) and their application in prosthodontic practice.

Setting and Design

A questionnaire based survey was carried out to assess the knowledge and awareness of PCL and its applications as provisional material in prosthodontic practice.

Materials and Method

A questionnaire-based descriptive study consisting of 10 questions related to different provisional materials and their applications in prosthodontic practice was formulated on Google Forms. The link was created and circulated among the prosthodontist faculty members of various dental institutes and private practitioners of India with the use of digital platforms such as E-mail and social media. The data were collected and examined using Microsoft Excel software for statistical evaluation.

Statistical Analysis Used

For this descriptive type of study, knowledge and awareness among prosthodontists across India was evaluated using Microsoft Excel software.

Results

The use of PCL was known only to 20.75% of prosthodontists. Moreover, its application and indications are known to only <1% of the study participants. Autopolymerizing resin was most commonly used for the custom tray and temporary base fabrication as well as temporization in crown and bridge prosthesis, while muscle deprogrammer and surgical template were commonly fabricated in heat-cure and clear acrylic resin, respectively. Pattern resin was found to be commonly used in splinting implant impression copings.

Conclusion

The use of PCL as a temporary denture base, custom tray, muscle deprogrammer, implant impression splinting, and provisional for crown and bridge and templates should be encouraged and incorporated to get benefits of its characteristic properties. Considering the overall performance of PCL, its use should be incorporated into prosthodontic research and practice.

The development of recycling methods for bio-based materials - A challenge in the implementation of a circular economy: A review

This review focuses on the characteristics of the most widely used biopolymers that contain starch, polylactic acid, cellulose and/or polybutylene succinate. Because worldwide production of bio-based materials has grown dynamically, their waste is increasingly found in the existing waste treatment plants. The development of recycling methods for bio-based materials remains a challenge in the implementation of a circular economy. This article summarizes the recycling methods for bio-based materials, which, in the hierarchy of waste management, is much more desirable than landfilling. Several methods of recycling are available for the end-of-life management of bio-based products, which include mechanical (reuse of waste as a valuable raw material for further processing), chemical (feedstock recycling) and organic (anaerobic digestion or composting) ones. The use of chemical or mechanical recycling is less favourable, more costly and requires the improvement of systems for separation of bio-based materials from the rest of the waste stream. Organic recycling can be a sustainable alternative to those two methods. In organic recycling, bio-based materials can be biologically treated under aerobic or anaerobic conditions, depending on the characteristics of the materials. The choice of the recycling method to be implemented depends on the economic situation and on the properties of the bio-based products and their susceptibility to degradation. Thus, it is necessary to label the products to indicate which method of recycling is most appropriate.

Biomaterials and Their Potentialities as Additives in Bitumen Technology: A Review

The carbon footprint reduction mandate and other eco-friendly policies currently in place are constantly driving the trend of the synthesis and application of sustainable functional materials. The bitumen industry is not an exception to this trend and, every day, new technologies that facilitate safer, cost effective and more sustainable industrial processes and road paving operations are being researched and brought to light. A lot of research is currently ongoing to improve bitumen's properties due to its use as a binder in road paving processes. Over the years, the most common method to improve bitumen's properties has been with the use of additives. The major drawback in the use of these additives is the fact that they are substances of strong chemical nature which are either too acidic, too basic or emit toxic fumes and volatile organic compounds into the environment. In the long run, these chemicals are also toxic to the road pavement personnel that carry out the day to day industrial and paving operations. This led researchers to the initiative of synthesizing and applying biomaterials to be used as additives for bitumen. In this light, several studies have investigated the use of substances such as bio-oils, natural waxes, gum, polysaccharides and natural rubber. This literature review is aimed at classifying the different bio-based materials used to improve bitumen's properties and to provide a deeper knowledge of the application of these biomaterials in bitumen technology. In general, we highlight how the research efforts elaborated herein could potentially foster safer, sustainable, eco-friendly approaches to improving bitumen's properties while also promoting a circular economy.

Marine-Derived Actinomycetes: Biodegradation of Plastics and Formation of PHA Bioplastics-A Circular Bioeconomy Approach

Plastics are present in the majority of daily-use products worldwide. Due to society's production and consumption patterns, plastics are accumulating in the environment, causing global pollution issues and intergenerational impacts. Our work aims to contribute to the development of solutions and sustainable methods to mitigate this pressing problem, focusing on the ability of marine-derived actinomycetes to accelerate plastics biodegradation and produce polyhydroxyalkanoates (PHAs), which are biodegradable bioplastics. The thin plastic films' biodegradation was monitored by weight loss, changes in the surface chemical structure (Infra-Red spectroscopy FTIR-ATR), and by mechanical properties (tensile strength tests). Thirty-six marine-derived actinomycete strains were screened for their plastic biodegradability potential. Among these, Streptomyces gougerotti, Micromonospora matsumotoense, and Nocardiopsis prasina revealed ability to degrade plastic films-low-density polyethylene (LDPE), polystyrene (PS) and polylactic acid (PLA) in varying conditions, namely upon the addition of yeast extract to the culture media and the use of UV pre-treated thin plastic films. Enhanced biodegradation by these bacteria was observed in both cases. S. gougerotti degraded 0.56% of LDPE films treated with UV radiation and 0.67% of PS films when inoculated with yeast extract. Additionally, N. prasina degraded 1.27% of PLA films when these were treated with UV radiation, and yeast extract was added to the culture medium. The main and most frequent differences observed in FTIR-ATR spectra during biodegradation occurred at 1740 cm^-1, indicating the formation of carbonyl groups and an increase in the intensity of the bands, which indicates oxidation. Young Modulus decreased by 30% on average. In addition, S. gougerotti and M. matsumotoense, besides biodegrading conventional plastics (LDPE and PS), were also able to use these as a carbon source to produce degradable PHA bioplastics in a circular economy concept.

Recent Advances in Biodegradable Polymers and Their Biological Applications: A Brief Review

The rising significance of the field of biopolymers has driven the rapid progress of this distinctive class of polymeric materials in the past decades. Biodegradable polymers have acquired much attention because they play an essential role in humans' lives due to their specific tunable electrical conductivity and biodegradability characteristics, making them fascinating in many applications. Herein, we debated the recent progress in developing biodegradable polymers and their applications. Initially, we introduce the basics of conducting and biodegradable polymers, trailed by debates about the effective strategies currently used to develop biopolymers. Special importance will focus on the uses of biodegradable polymers in drug delivery and tissue engineering, as well as wound healing, demonstrating the recent findings, and uses of several biodegradable polymers in modern biological uses. In this review, we have provided comprehensive viewpoints on the latest progress of the challenges and future prospects involving biodegradable polymers' advancement and commercial applications.

An update on polyethylene and biodegradable plastic mulch films and their impact on the environment

Many ways are being developed in the realm of agriculture to increase crop yield while inflicting minimal damage to the soil and environment. One among them is the application of agricultural, biodegradable mulch (BDM) films. Organic substances or synthetic materials are used for making mulches. Also, bio-based polymers derived from bacteria, microorganisms, or fossil fuels are used to make BDM films. BDM films are used in crop production because of their high agronomical advantages which lead to sustainable agriculture. These films are placed on the soil's surface, around the plants. Mulches help in conserving the moisture, control the temperature of the soil, control the growth of the weed, and help in the utilization of soil nutrients thus, overall enhancing the crop yield. The usage of plastic mulch in agriculture has expanded substantially all around the world, over the past ten years, this is because polyethylene films are cheaper, easily produced, highly flexible, and durable. However, the improper disposal of used plastic films has resulted in soil pollution and environmental contamination. Traditional mulches are replaced by BDM, which is a more environmentally friendly alternative. After being used, degradable mulch films could be tilled into the soil and are expected to disintegrate over time. This review focuses on the BDMs, their history, plastic mulches, how BDMs became an alternative source for plastic mulches, their composition, and also addresses their significance. In addition, we discuss the environmental impact of films, including how it alters the climate, soil, temperature, and weed management.

Advances in Biodegradable Soft Robots

Biodegradable soft robots have been proposed for a variety of intelligent applications in soft robotics, flexible electronics, and bionics. Biodegradability offers an extraordinary functional advantage to soft robots for operations accompanying smart shape transformation in response to external stimuli such as heat, pH, and light. This review primarily surveyed the current advanced scientific and engineering strategies for integrating biodegradable materials within stimuli-responsive soft robots. It also focused on the fabrication methodologies of multiscale biodegradable soft robots, and highlighted the role of biodegradable soft robots in enhancing the multifunctional properties of drug delivery capsules, biopsy tools, smart actuators, and sensors. Lastly, the current challenges and perspectives on the future development of intelligent soft robots for operation in real environments were discussed.

Recent Advances in Starch-Based Blends and Composites for Bioplastics Applications

Environmental pollution by synthetic polymers is a global problem and investigating substitutes for synthetic polymers is a major research area. Starch can be used in formulating bioplastic materials, mainly as blends or composites with other polymers. The major drawbacks of using starch in such applications are water sensitivity and poor mechanical properties. Attempts have been made to improve the mechanical properties of starch-based blends and composites, by e.g., starch modification or plasticization, matrix reinforcement, and polymer blending. Polymer blending can bring synergetic benefits to blends and composites, but necessary precautions must be taken to ensure the compatibility of hydrophobic polymers and hydrophilic starch. Genetic engineering offers new possibilities to modify starch inplanta in a manner favorable for bioplastics applications, while the incorporation of antibacterial and/or antioxidant agents into starch-based food packaging materials brings additional advantages. In conclusion, starch is a promising material for bioplastic production, with great potential for further improvements. This review summarizes the recent advances in starch-based blends and composites and highlights the potential strategies for overcoming the major drawbacks of using starch in bioplastics applications.

Novel Approach in Biodegradation of Synthetic Thermoplastic Polymers: An Overview

Biodegradation is necessary for water-soluble or water-immiscible polymers because they eventually enter streams which can neither be recycled nor incinerated. It is important to consider the microbial degradation of natural and synthetic polymers in order to understand what is necessary for biodegradation and the mechanisms involved. Low/high-density polyethylene is a vital cause of environmental pollution. It occurs by choking the sewer line through mishandling, thus posing an everlasting ecological threat. Environmental pollution due to the unscrupulous consumption of synthetic polymers derived from petroleum has an adverse impact on the environment since the majority of plastics do not degrade, and the further incineration of synthetic plastics generates CO2 and dioxin. This requires understanding the interactions between materials and microorganisms and the biochemical changes involved. Widespread studies on the biodegradation of plastics have been carried out in order to overcome the environmental problems associated with synthetic plastic waste. Awareness of the waste problem and its impact on the environment has awakened new interest in the area of degradable polymers through microbes viz., bacteria, fungi, and actinomycetes. The microbial degradation of plastics is caused by certain enzymatic activities that lead to a chain cleavage of polymers into oligomers and monomers. This review focuses on the biodegradation rate of plastics by fungal and bacterial communities and the mode of action of biodegradation.

Biodegradation of Biodegradable Polymers in Mesophilic Aerobic Environments

Finding alternatives to diminish plastic pollution has become one of the main challenges of modern life. A few alternatives have gained potential for a shift toward a more circular and sustainable relationship with plastics. Biodegradable polymers derived from bio- and fossil-based sources have emerged as one feasible alternative to overcome inconveniences associated with the use and disposal of non-biodegradable polymers. The biodegradation process depends on the environment's factors, microorganisms and associated enzymes, and the polymer properties, resulting in a plethora of parameters that create a complex process whereby biodegradation times and rates can vary immensely. This review aims to provide a background and a comprehensive, systematic, and critical overview of this complex process with a special focus on the mesophilic range. Activity toward depolymerization by extracellular enzymes, biofilm effect on the dynamic of the degradation process, CO2 evolution evaluating the extent of biodegradation, and metabolic pathways are discussed. Remarks and perspectives for potential future research are provided with a focus on the current knowledge gaps if the goal is to minimize the persistence of plastics across environments. Innovative approaches such as the addition of specific compounds to trigger depolymerization under particular conditions, biostimulation, bioaugmentation, and the addition of natural and/or modified enzymes are state-of-the-art methods that need faster development. Furthermore, methods must be connected to standards and techniques that fully track the biodegradation process. More transdisciplinary research within areas of polymer chemistry/processing and microbiology/biochemistry is needed.