Cesium-containing triple cation perovskite solar cells: improved stability, reproducibility and high efficiency

Sustainable Mixed-Halide Perovskite Resistive Switching Memories Using Self-Assembled Monolayers as the Bottom Contact

The complex ionic-electronic conduction in mixed halide perovskites enables their use beyond von Neumann architectures implemented in resistive switching memory devices. Although device fabrication based on perovskite compounds involves solution-processing at low temperatures, reducing further fabrication costs by eliminating expensive materials can improve their compatibility with upscalable deposition techniques. Notably, the substrate on which the perovskite active layer is developed has been reported to severely affect its quality and thus the overall device performance. Hereby, we demonstrate the sustainable manufacturing of memristive perovskite solar cells by replacing the expensive poly[bis(4-phenyl)(2,4,6-trimethylphenyl)amine] (PTAA) that serves as a hole transporting layer (HTL) with a self-assembled monolayer (SAM), namely [2-(3,6-dimethoxy-9H-carbazol-9-yl)ethyl]phosphonic acid (MeO-2PACz). Multiple sequential memristive current-voltage characteristics of single devices are reported, and average data of multiple reference and targeted devices are compared. Resistive switching memory devices based on SAM exhibit improved performance having reduced average SET voltage values and narrower statistical variation compared to reference devices with PTAA. It is shown that both PTAA and SAM based devices exhibit high ON/OFF ratio of about 103 operating at low switching electric fields. Replacing an expensive polymer-based HTL with this approach reduces fabrication costs compared to PTAA.

High-entropy alloy screening for halide perovskites

As the concept of high-entropy alloying (HEA) extends beyond metals, new materials screening methods are needed. Halide perovskites (HP) are a prime case study because greater stability is needed for photovoltaics applications, and there are 322 experimentally observed HP end-members, which leads to more than 1057 potential alloys. We screen HEAHP by first calculating the configurational entropy of 106 equimolar alloys with experimentally observed end-members. To estimate enthalpy at low computational cost, we turn to the delta-lattice parameter approach, a well-known method for predicting III-V alloy miscibility. To generalize the approach for non-cubic crystals, we introduce the parameter of unit cell volume coefficient of variation (UCV), which does a good job of predicting the experimental HP miscibility data. We use plots of entropy stabilization versus UCV to screen promising alloys and identify 102 HEAHP of interest.

Quantifying Organic Cation Ratios in Metal Halide Perovskites: Insights from X-ray Photoelectron Spectroscopy and Nuclear Magnetic Resonance Spectroscopy

The employment of metal halide perovskites (MHPs) in various optoelectronic applications requires the preparation of thin films whose composition plays a crucial role. Yet, the composition of the MHP films is rarely reported in the literature, partly because quantifying the actual organic cation composition cannot be done with conventional characterization methods. For MHPs, NMR has gained popularity, but for films, tedious processes like scratching several films are needed. Here, we use mechanochemical synthesis of MA1-x FA x PbI3 powders with various MA+: FA+ ratios and combine solid-state NMR spectroscopy (ssNMR) and X-ray photoelectron spectroscopy (XPS) to provide a reference characterization protocol for the organic cations' quantification in either powder form or films. Following this, we demonstrate that organic cation ratio quantification on thin films with ssNMR can be done without scraping the film and using significantly less mass than typically needed, that is, employing a single ∼800 nm-thick MA1-x FA x PbI3 film deposited by pulsed laser deposition (PLD) onto a 1 × 1 in.2, 0.2 mm-thick quartz substrate. While background signals from the quartz substrate appear in the 1H ssNMR spectra, the MA+ and FA+ signals are easily distinguishable and can be quantified. This study highlights the importance of calibrating and quantifying the source and the thin film organic cation ratio, as key for future optimization and scalability of physical vapor deposition processes.

Bromine Incorporation Affects Phase Transformations and Thermal Stability of Lead Halide Perovskites

Mixed-cation and mixed-halide lead halide perovskites show great potential for their application in photovoltaics. Many of the high-performance compositions are made of cesium, formamidinium, lead, iodine, and bromine. However, incorporating bromine in iodine-rich compositions and its effects on the thermal stability of the perovskite structure has not been thoroughly studied. In this work, we study how replacing iodine with bromine in the state-of-the-art Cs0.17FA0.83PbI3 perovskite composition leads to different dynamics in the phase transformations as a function of temperature. Through a combination of structural characterization, cathodoluminescence mapping, X-ray photoelectron spectroscopy, and first-principles calculations, we reveal that the incorporation of bromine reduces the thermodynamic phase stability of the films and shifts the products of phase transformations. Our results suggest that bromine-driven vacancy formation during high temperature exposure leads to irreversible transformations into PbI2, whereas materials with only iodine go through transformations into hexagonal polytypes, such as the 4H-FAPbI3 phase. This work sheds light on the structural impacts of adding bromine on thermodynamic phase stability and provides new insights into the importance of understanding the complexity of phase transformations and secondary phases in mixed-cation and mixed-halide systems.

Positive Effects of Guanidinium Salt Post-Treatment on Multi-Cation Mixed Halide Perovskite Solar Cells

As one of the most promising photovoltaic technologies, perovskite solar cells (PSCs) exhibit high absorption coefficients, tunable bandgaps, large carrier mobilities, and versatile fabrication techniques. Nevertheless, the commercialization of the technology is hindered by poor material stability, short device lifetimes and the scalability of fabrication techniques. To address these technological drawbacks, various strategies have been explored, with one particularly promising approach involving the formation of a low-dimensional layer on the surface of the three-dimensional perovskite film. In this work, we demonstrate the use of guanidinium tetrafluoroborate, CH6BF4N3, (GATFB) as a post-treatment step to enhance the performance of PSCs. Compared with the control sample, the application of GATFB improves the film surface topology, reduces surface defects, suppresses non-radiative recombination, and optimizes band alignment within the device. These positive effects reduce recombination losses and enhance charge transport in the device, resulting in PSCs with an open-circuit voltage (VOC) of 1.18 V and a power conversion efficiency (PCE) of 19.7%. The results obtained in this work exhibit the potential of integrating low-dimensional structures in PSCs as an effective approach to enhance the overall device performance, providing useful information for further advancement in this rapidly evolving field of photovoltaic technology.

GIWAXS experimental methods at the NFPS-BL17B beamline at Shanghai Synchrotron Radiation Facility

The BL17B beamline at the Shanghai Synchrotron Radiation Facility was first designed as a versatile high-throughput protein crystallography beamline and one of five beamlines affiliated to the National Facility for Protein Science in Shanghai. It was officially opened to users in July 2015. As a bending magnet beamline, BL17B has the advantages of high photon flux, brightness, energy resolution and continuous adjustable energy between 5 and 23 keV. The experimental station excels in crystal screening and structure determination, providing cost-effective routine experimental services to numerous users. Given the interdisciplinary and green energy research demands, BL17B beamline has undergone optimization, expanded its range of experimental methods and enhanced sample environments for a more user-friendly testing mode. These methods include single-crystal X-ray diffraction, powder crystal X-ray diffraction, wide-angle X-ray scattering, grazing-incidence wide-angle X-ray scattering (GIWAXS), and fully scattered atom pair distribution function analysis, covering structure detection from crystalline to amorphous states. This paper primarily presents the performance of the BL17B beamline and the application of the GIWAXS methodology at the beamline in the field of perovskite materials.

Cost-Effective Synthesis Method: Toxic Solvent-Free Approach for Stable Mixed Cation Perovskite Powders in Photovoltaic Applications

Organometallic lead halide perovskite powders have gained widespread attention for their intriguing properties, showcasing remarkable performance in the optoelectronic applications. In this study, formamidinium lead iodide (α-FAPbI3) microcrystals (MCs) is synthesized using retrograde solubility-driven crystallization. Additionally, methylammonium lead bromide (MAPbBr3) and cesium lead iodide (δ-CsPbI3) MCs are prepared through a sonochemical process, employing low-grade PbX2 (X = I & Br) precursors and an eco-friendly green solvent (γ-Valerolactone). The study encompasses an analysis of the structural, optical, thermal, elemental, and morphological characteristics of FAPbI3, MAPbBr3, and CsPbI3 MCs. Upon analysing phase stability, a phase transition in FAPbI3 MCs is observed after 2 weeks. To address this issue, a powder-based mechanochemical method is employed to synthesize stable mixed cation perovskite powders (MCPs) by subjecting FAPbI3 and MAPbBr3 MCs with varying concentrations of CsPbI3. Furthermore, the performance of mixed cation perovskites are examined using the Solar Cell Capacitance Simulator (SCAPS-1D) software. The impact of cesium incorporation in the photovoltaic characteristics is elucidated. All mixed cation absorbers exhibited optimal device performance with a thickness ranging between 0.6-1.5 µm. It's worth noting that the MCPs exhibit impressive ambient stability, remaining structurally intact and retaining their properties without significant degradation for 70 days of ambient exposure.

Dark Current in Broadband Perovskite-Organic Heterojunction Photodetectors Controlled by Interfacial Energy Band Offset

Lead halide perovskite and organic semiconductors are promising classes of materials for photodetector (PD) applications. State-of-the-art perovskite PDs have performance metrics exceeding silicon PDs in the visible. While organic semiconductors offer bandgap tunability due to their chemical design with detection extended into the near-infrared (NIR), perovskites are limited to the visible band and the first fraction of the NIR spectrum. In this work, perovskite-organic heterojunction (POH) PDs with absorption up to 950 nm are designed by the dual contribution of perovskite and the donor:acceptor bulk-heterojunction (BHJ), without any intermediate layer. The effect of the energetics of the donor materials is systematically studied on the dark current (Jd) of the device by using the PBDB-T polymer family. Combining the experimental results with drift-diffusion simulations, it is shown that Jd in POH devices is limited by thermal generation via deep trap states in the BHJ. Thus, the best performance is obtained for the PM7-based POH, which delivers an ultra-low noise current of 2 × 10-14 A Hz-1/2 and high specific detectivity of 4.7 × 1012 Jones in the NIR. Last, the application of the PM7-based POH devices as NIR pulse oximeter with high-accuracy heartbeat monitoring at long-distance of 2 meters is demonstrated.

Two-dimensional perovskite templates for durable, efficient formamidinium perovskite solar cells

We present a design strategy for fabricating ultrastable phase-pure films of formamidinium lead iodide (FAPbI3) by lattice templating using specific two-dimensional (2D) perovskites with FA as the cage cation. When a pure FAPbI3 precursor solution is brought in contact with the 2D perovskite, the black phase forms preferentially at 100°C, much lower than the standard FAPbI3 annealing temperature of 150°C. X-ray diffraction and optical spectroscopy suggest that the resulting FAPbI3 film compresses slightly to acquire the (011) interplanar distances of the 2D perovskite seed. The 2D-templated bulk FAPbI3 films exhibited an efficiency of 24.1% in a p-i-n architecture with 0.5-square centimeter active area and an exceptional durability, retaining 97% of their initial efficiency after 1000 hours under 85°C and maximum power point tracking.

The Effect of Cesium Incorporation on the Vibrational and Elastic Properties of Methylammonium Lead Chloride Perovskite Single Crystals

Hybrid organic-inorganic lead halide perovskites (LHPs) have emerged as a highly significant class of materials due to their tunable and adaptable properties, which make them suitable for a wide range of applications. One of the strategies for tuning and optimizing LHP-based devices is the substitution of cations and/or anions in LHPs. The impact of Cs substitution at the A site on the structural, vibrational, and elastic properties of MAxCs1-xPbCl3-mixed single crystals was investigated using X-ray diffraction (XRD) and Raman and Brillouin light scattering techniques. The XRD results confirmed the successful synthesis of impurity-free single crystals, which exhibited a phase coexistence of dominant cubic and minor orthorhombic symmetries. Raman spectroscopy was used to analyze the vibrational modes associated with the PbCl6 octahedra and the A-site cation movements, thereby revealing the influence of cesium incorporation on the lattice dynamics. Brillouin spectroscopy was employed to investigate the changes in elastic properties resulting from the Cs substitution. The incorporation of Cs cations induced lattice distortions within the inorganic framework, disrupting the hydrogen bonding between the MA cations and PbCl6 octahedra, which in turn affected the elastic constants and the sound velocities. The substitution of the MA cations with smaller Cs cations resulted in a stiffer lattice structure, with the two elastic constants increasing up to a Cs content of 30%. The current findings facilitate a fundamental understanding of mixed lead chloride perovskite materials, providing valuable insights into their structural and vibrational properties.

Comparative Analysis of the Stability and Performance of Double-, Triple-, and Quadruple-Cation Perovskite Solar Cells for Rooftop and Indoor Applications

The solar energy market is predicted to be shared between Si solar cells and third-generation photovoltaics in the future. Perovskite solar cells (PSCs) show the greatest potential to capture a share there as a single junction or in tandem with silicon. Researchers worldwide are looking to optimize the composition of the perovskite film to achieve an optimal bandgap, performance, and stability. Traditional perovskites have a mixture of formamidinium and methyl ammonium as the A-site cation in their ABX3 structure. However, in recent times, the use of cesium and rubidium has become popular for making highly efficient PSCs. A thorough analysis of the performance and stability of double-, triple-, and quadruple-cation PSCs under different environmental conditions was performed in this study. The performance of the device and the films was analyzed by electrical measurements (J-V, dark J-V, EQE), scanning electron microscopy, atomic force microscopy, photoluminescence, and X-ray diffraction. The quadruple-cation device with the formula Cs0.07Rb0.03FA0.77MA0.13PbI2.8Br0.2 showed the highest power conversion efficiency (PCE) of 21.7%. However, this device had the least stability under all conditions. The triple-cation device with the formula Cs0.1FA0.6MA0.3PbI2.8Br0.2, with a slightly lower PCE (21.2%), was considerably more stable, resulting in about 30% more energy harvested than that using the other two devices during their life cycle.

Multiple Stabilization Effects of Benzylhydrazine on Scalable Perovskite Precursor Inks for Improved Perovskite Solar Cell Production

Perovskite precursor inks suffer various forms of degradation, such as iodide anion oxidation and organic cation breakdown, hindering reliable perovskite solar cell manufacturing. Here we report that benzylhydrazine hydrochloride (BHC) not only retards the buildup of iodine as previously reported but also prevents the breakdown of organic cations. Through investigating BHC and iodine chemical reactions, we elucidate protonation and dehydration mechanisms, converting BHC to harmless volatile compounds, thus preserving perovskite film crystallization and solar cell performance. This inhibition effect lasts nearly a month with minimal BHC, contrasting control inks without BHC where organic cations fully react in less than a week. This enhanced understanding, from additive stabilization to end products, promises improved perovskite solar cell production reliability.

Improving the Efficiency and Stability of Perovskite Solar Cells by Refining the Perovskite-Electron Transport Layer Interface and Shielding the Absorber from UV Effects

This study aims to enhance the performance of perovskite solar cells (PSCs) by optimizing the interface between the perovskite and electron transport layers (ETLs). Additionally, we plan to protect the absorber layer from ultraviolet (UV) degradation using a ternary oxide system comprising SnO2, strontium stannate (SrSnO3), and strontium oxide (SrO). In this structure, the SnO2 layer functions as an electron transport layer, SrSnO3 acts as a layer for UV filtration, and SrO is employed to passivate the interface. SrSnO3 is characterized by its chemical stability, electrical conductivity, extensive wide band gap energy, and efficient absorption of UV radiation, all of which significantly enhance the photostability of PSCs against UV radiation. Furthermore, incorporating SrSnO3 into the ETL improves its electronic properties, potentially raising the energy level and improving alignment, thereby enhancing the electron transfer from the perovskite layer to the external circuit. Integrating SrO at the interface between the ETL and perovskite layer reduces interface defects, thereby reducing charge recombination and improving electron transfer. This improvement results in higher solar cell efficiency, reduced hysteresis, and extended device longevity. The benefits of this method are evident in the observed improvements: a noticeable increase in open-circuit voltage (Voc) from 1.12 to 1.16 V, an enhancement in the fill factor from 79.4 to 82.66%, a rise in the short-circuit current density (Jsc) from 24.5 to 24.9 mA/cm2 and notably, a marked improvement in the power conversion efficiency (PCE) of PSCs, from 21.79 to 24.06%. Notably, the treated PSCs showed only a slight decline in PCE, reducing from 24.15 to 22.50% over nearly 2000 h. In contrast, untreated SnO2 perovskite devices experienced a greater decline, with efficiency decreasing from 21.79 to 17.83% in just 580 h.

Alleviating nanostructural phase impurities enhances the optoelectronic properties, device performance and stability of cesium-formamidinium metal-halide perovskites

The technique of alloying FA+ with Cs+ is often used to promote structural stabilization of the desirable α-FAPbI3 phase in halide perovskite devices. However, the precise mechanisms by which these alloying approaches improve the optoelectronic quality and enhance the stability have remained elusive. In this study, we advance that understanding by investigating the effect of cationic alloying in CsxFA1-xPbI3 perovskite thin-films and solar-cell devices. Selected-area electron diffraction patterns combined with microwave conductivity measurements reveal that fine Cs+ tuning (Cs0.15FA0.85PbI3) leads to a minimization of stacking faults and an increase in the photoconductivity of the perovskite films. Ultra-sensitive external quantum efficiency, kelvin-probe force microscopy and photoluminescence quantum yield measurements demonstrate similar Urbach energy values, comparable surface potential fluctuations and marginal impact on radiative emission yields, respectively, irrespective of Cs content. Despite this, these nanoscopic defects appear to have a detrimental impact on inter-grains'/domains' carrier transport, as evidenced by conductive-atomic force microscopy and corroborated by drastically reduced solar cell performance. Importantly, encapsulated Cs0.15FA0.85PbI3 devices show robust operational stability retaining 85% of the initial steady-state power conversion efficiency for 1400 hours under continuous 1 sun illumination at 35 °C, in open-circuit conditions. Our findings provide nuance to the famous defect tolerance of halide perovskites while providing solid evidence about the detrimental impact of these subtle structural imperfections on the long-term operational stability.

Graphene-Perovskite Fibre Photodetectors

The integration of optoelectronic devices, such as transistors and photodetectors (PDs), into wearables and textiles is of great interest for applications such as healthcare and physiological monitoring. These require flexible/wearable systems adaptable to body motions, thus materials conformable to non-planar surfaces, and able to maintain performance under mechanical distortions. Here, fibre PDs are prepared by combining rolled graphene layers and photoactive perovskites. Conductive fibres (~500 Ωcm-1) are made by rolling single-layer graphene (SLG) around silica fibres, followed by deposition of a dielectric layer (Al2O3 and parylene C), another rolled SLG as a channel, and perovskite as photoactive component. The resulting gate-tunable PD has a response time~9ms, with an external responsivity~22kAW-1 at 488nm for a 1V bias. The external responsivity is two orders of magnitude higher, and the response time one order of magnitude faster, than state-of-the-art wearable fibre-based PDs. Under bending at 4mm radius, up to~80% photocurrent is maintained. Washability tests show~72% of initial photocurrent after 30 cycles, promising for wearable applications.

Buried Interface Passivation Using Organic Ammonium Salts for Efficient Inverted CsMAFA Perovskite Solar Cell Performance

This study uses different doping ratios of CsCl and MACl dual additives to improve the quality of the perovskite, where CsCl reduces the perovskite trap density and increases the resistance of charge recombination, and MACl was used to improve the phase stability. Finally, the composition of Cs0.1MA0.09FA0.81PbCl0.14I2.86 perovskite solar cell (PeSC) can achieve better open-circuit voltage (Voc), short-circuit current density (Jsc), and photoelectric conversion efficiency (PCE). To achieve a better PCE of PeSC, the use of organic ammonium salt butane-1,4-diammonium iodide (BDAI2) to passivate the perovskite bottom surface (buried interface) can effectively suppress the formation of defects at the perovskite buried interface, obtain higher crystallinity, and thereby reduce the probability of carrier recombination. The Jsc, fill factor (FF), and PCE of the PeSC based on BDAI2 passivation increased from 24.0 mA cm-2, 74.1%, and 18.6% to 24.5 mA cm-2, 79.9%, and 20.5%, respectively.

Solvent-free preparation and thermocompression self-assembly: an exploration of performance improvement strategies for perovskite solar cells

Perovskite solar cells (PSCs) exhibit sufficient technological efficiency and economic competitiveness. However, their poor stability and scalability are crucial factors limiting their rapid development. Therefore, achieving both high efficiency and good stability is an urgent challenge. In addition, the preparation methods for PSCs are currently limited to laboratory-scale methods, so their commercialization requires further research. Effective packaging technology is essential to protect the PSCs from degradation by external environmental factors and ensure their long-term stability. The industrialization of PSCs is also inseparable from the preparation technology of perovskite thin films. This review discusses the solvent-free preparation of PSCs, shedding light on the factors that affect PSC performance and strategies for performance enhancement. Furthermore, this review analyzes the existing simulation techniques that have contributed to a better understanding of the interfacial evolution of PSCs during the packaging process. Finally, the current challenges and possible solutions are highlighted, providing insights to facilitate the development of highly efficient and stable PSC modules to promote their widespread application.

Band gap tuning of perovskite solar cells for enhancing the efficiency and stability: issues and prospects

The intriguing optoelectronic properties, diverse applications, and facile fabrication techniques of perovskite materials have garnered substantial research interest worldwide. Their outstanding performance in solar cell applications and excellent efficiency at the lab scale have already been proven. However, owing to their low stability, the widespread manufacturing of perovskite solar cells (PSCs) for commercialization is still far off. Several instability factors of PSCs, including the intrinsic and extrinsic instability of perovskite materials, have already been identified, and a variety of approaches have been adopted to improve the material quality, stability, and efficiency of PSCs. In this review, we have comprehensively presented the significance of band gap tuning in achieving both high-performance and high-stability PSCs in the presence of various degradation factors. By investigating the mechanisms of band gap engineering, we have highlighted its pivotal role in optimizing PSCs for improved efficiency and resilience.

Defects and Defect Passivation in Perovskite Solar Cells

Perovskite solar cells have made significant strides in recent years. However, there are still challenges in terms of photoelectric conversion efficiency and long-term stability associated with perovskite solar cells. The presence of defects in perovskite materials is one of the important influencing factors leading to subpar film quality. Adopting additives to passivate defects within perovskite materials is an effective approach. Therefore, we first discuss the types of defects that occur in perovskite materials and the mechanisms of their effect on performance. Then, several types of additives used in perovskite solar cells are discussed, including ionic compounds, organic molecules, polymers, etc. This review provides guidance for the future development of more sustainable and effective additives to improve the performance of solar cells.

High-Throughput Deposition of Recyclable SnO2 Electrodes toward Efficient Perovskite Solar Cells

Chemical bath deposited (CBD) SnO2 is one of the most prevailing electron transport layers for realizing high-efficiency perovskite solar cells (PSCs) so far. However, the state-of-the-art CBD SnO2 process is time-consuming, contradictory to its prospect in industrialization. Herein, a simplified yet efficient method is developed for the fast deposition of SnO2 electrodes by incorporating a concentrated Sn source stabilized by the ethanol ligand with antimony (Sb) doping. The higher concentration of Sn source promotes the deposition rate, and Sb doping improves the hole-blocking capability of the CBD SnO2 layer so that its target thickness can be reduced to further save the deposition time. As a result, the deposition time can be appreciably reduced from 3-4 h to only 5 min while maintaining 95% of the maximum efficiency, indicating the power of the method toward high-throughput production of efficient PSCs. Additionally, the CBD SnO2 substrates are recyclable after removing the upper layers of complete PSCs, and the refurbished PSCs can maintain ≈98% of their initial efficiency after three recycling-and-fabrication processes.

Mechanical Durability and Flexibility in Perovskite Photovoltaics: Advancements and Applications

The remarkable progress in perovskite solar cell (PSC) technology has witnessed a remarkable leap in efficiency within the past decade. As this technology continues to mature, flexible PSCs (F-PSCs) are emerging as pivotal components for a wide array of applications, spanning from powering portable electronics and wearable devices to integrating seamlessly into electronic textiles and large-scale industrial roofing. F-PSCs characterized by their lightweight, mechanical flexibility, and adaptability for cost-effective roll-to-roll manufacturing, hold immense commercial potential. However, the persistent concerns regarding the overall stability and mechanical robustness of these devices loom large. This comprehensive review delves into recent strides made in enhancing the mechanical stability of F-PSCs. It covers a spectrum of crucial aspects, encompassing perovskite material optimization, precise crystal grain regulation, film quality enhancement, strategic interface engineering, innovational developed flexible transparent electrodes, judicious substrate selection, and the integration of various functional layers. By collating and analyzing these dedicated research endeavors, this review illuminates the current landscape of progress in addressing the challenges surrounding mechanical stability. Furthermore, it provides valuable insights into the persistent obstacles and bottlenecks that demand attention and innovative solutions in the field of F-PSCs.

Direct Integration of Perovskite Solar Cells with Carbon Fiber Substrates

Integrating photovoltaic devices onto the surface of carbon-fiber-reinforced polymer substrates should create materials with high mechanical strength that are also able to generate electrical power. Such devices are anticipated to find ready applications as structural, energy-harvesting systems in both the automotive and aeronautical sectors. Here, the fabrication of triple-cation perovskite n-i-p solar cells onto the surface of planarized carbon-fiber-reinforced polymer substrates is demonstrated, with devices utilizing a transparent top ITO contact. These devices also contain a "wrinkled" SiO2 interlayer placed between the device and substrate that alleviates thermally induced cracking of the bottom ITO layer. Devices are found to have a maximum stabilized power conversion efficiency of 14.5% and a specific power (power per weight) of 21.4 W g-1 (without encapsulation), making them highly suitable for mobile power applications.

Cs and Br tuning to achieve ultralow-hysteresis and high-performance indoor triple cation perovskite solar cell with low-cost carbon-based electrode

With high efficacy for electron-photon conversion under low light, perovskite materials show great potential for indoor solar cell applications to power small electronics for internet of things (IoTs). To match the spectrum of an indoor LED light source, triple cation perovskite composition was varied to adjust band gap values via Cs and Br tuning. However, increased band gaps lead to morphology, phase instability, and defect issues. 10% Cs and 30% Br strike the right balance, leading to low-cost carbon-based devices with the highest power conversion efficiency (PCE) of 31.94% and good stability under low light cycles. With further improvement in device stack and size, functional solar cells with the ultralow hysteresis index (HI) of 0.1 and the highest PCE of 30.09% with an active area of 1 cm2 can be achieved. A module from connecting two such cells in series can simultaneously power humidity and temperature sensors under 1000 lux.

Photo-Cross-Linked Fullerene-Based Hole Transport Material for Moisture-Resistant Regular Fullerene Sandwich Perovskite Solar Cells

Despite the high efficiencies currently achieved with perovskite solar cells (PSCs), the need to develop stable devices, particularly in humid conditions, still remains. This study presents the synthesis of a novel photo-cross-linkable fullerene-based hole transport material named FT12. For the first time, the photo-cross-linking process is applied to PSCs, resulting in the preparation of photo-cross-linked FT12 (PCL FT12). Regular PSCs based on C60-sandwich architectures were fabricated using FT12 and PCL FT12 as dopant-free hole transport layers (HTLs) and compared to the reference spiro-OMeTAD. The photovoltaic results demonstrate that both FT12 and PCL FT12 significantly outperform pristine spiro-OMeTAD regarding device performance and stability. The comparison between devices based on FT12 and PCL FT12 demonstrates that the photo-cross-linking process enhances device efficiency. This improvement is primarily attributed to enhanced charge extraction, partial oxidation of the HTL, increased hole mobility, and improved layer morphology. PCL FT12-based devices exhibit improved stability compared to FT12 devices, primarily due to the superior moisture resistance achieved through photo-cross-linking.

Passivating Defects via Retarding the Reaction Rate of FAI and PbI2 Enables Stable Perovskite Solar Cells

The two-step sequential deposition strategy has garnered widespread usage in the fabrication of high-performance perovskite solar cells based on FAPbI3. However, the rapid reaction between FAI and PbI2 during preparation often leads to incomplete reactions, reducing the device efficiency and stability. Herein, we introduced a multifunctional additive, 2-thiophenyl trifluoroacetone (TTA), into the FAI precursor. The incorporation of TTA has proven to be highly effective in slowing the reaction rate between FAI and PbI2, resulting in increased perovskite formation and improved efficiency and stability of the devices. TTA's CF3 groups interact with FAI via hydrogen bonding, effectively suppressing FA+ defects. The S and C═O groups share lone pair electrons with uncoordinated Pb2+, leading to a reduction in perovskite film defects and suppressing nonradiative recombination. Additionally, the CF3 groups impart hydrophobicity, protecting the perovskite film from moisture-induced erosion. As a result, the TTA-modified perovskite film achieves a Champion efficiency of 23.42% compared to the control's 21.52, with 20.58% efficiency for a 25 cm2 solar module. Remarkably, the unencapsulated Champion device retains 86% of its initial PCE after 1080 h under dark conditions (60 ± 5 °C, 35 ± 5% RH), indicating enhanced long-term stability. These findings offer a promising and cost-effective tactic for high-quality perovskite film fabrication.

Constructing Ultra-Shallow Near-Edge States for Efficient and Stable Perovskite Solar Cells

Electronic band structure engineering of metal-halide perovskites (MHP) lies at the core of fundamental materials research and photovoltaic applications. However, reconfiguring the band structures in MHP for optimized electronic properties remains challenging. This article reports a generic strategy for constructing near-edge states to improve carrier properties, leading to enhanced device performances. The near-edge states are designed around the valence band edge using theoretical prediction and constructed through tailored material engineering. These states are experimentally revealed with activation energies of around 23 milli-electron volts by temperature-dependent time-resolved spectroscopy. Such small activation energies enable prolonged carrier lifetime with efficient carrier transition dynamics and low non-radiative recombination losses, as corroborated by the millisecond lifetimes of microwave conductivity. By constructing near-edge states in positive-intrinsic-negative inverted cells, a champion efficiency of 25.4% (25.0% certified) for a 0.07-cm2 cell and 23.6% (22.7% certified) for a 1-cm2 cell is achieved. The most stable encapsulated cell retains 90% of its initial efficiency after 1100 h of maximum power point tracking under one sun illumination (100 mW cm-2) at 65 °C in ambient air.

A Self-Assembled 3D/0D Quasi-Core-Shell Structure as Internal Encapsulation Layer for Stable and Efficient FAPbI3 Perovskite Solar Cells and Modules

FAPbI3 perovskites have garnered considerable interest owing to their outstanding thermal stability, along with near-theoretical bandgap and efficiency. However, their inherent phase instability presents a substantial challenge to the long-term stability of devices. Herein, this issue through a dual-strategy of self-assembly 3D/0D quasi-core-shell structure is tackled as an internal encapsulation layer, and in situ introduction of excess PbI2 for surface and grain boundary defects passivating, therefore preventing moisture intrusion into FAPbI3 perovskite films. By utilizing this method alone, not only enhances the stability of the FAPbI3 film but also effectively passivates defects and minimizes non-radiative recombination, ultimately yielding a champion device efficiency of 23.23%. Furthermore, the devices own better moisture resistance, exhibiting a T80 lifetime exceeding 3500 h at 40% relative humidity (RH). Meanwhile, a 19.51% PCE of mini-module (5 × 5 cm2) is demonstrated. This research offers valuable insights and directions for the advancement of stable and highly efficient FAPbI3 perovskite solar cells.

Can thick metal-halide perovskite single crystals have narrower optical bandgaps with near-infrared absorption?

Metal-halide perovskite (MHP) single crystals are emerging as potential competitors to their polycrystalline thin-film counterparts. These materials have shown the specific feature of extended absorbance towards the near-infrared (NIR) region, which promises further extension of their applications in the field of photovoltaics and photodetectors. This notable expansion of absorbance has been explained by the narrower effective optical bandgap of MHP single crystals promoted by their large thickness over several micrometres to millimetres. Herein, the attributes of the material's thickness and the measurement technique used to estimate these characteristics are discussed to elucidate the actual origins of the extended absorbance of MHP single crystals. Contrary to the general belief of the narrower bandgap of the MHP single crystals, we demonstrate that the extended NIR absorption in the MHP single crystals mainly originates from the combination of unique below-bandgap absorption of MHPs, the thickness of single crystals, and the technical limitation of the spectrophotometer, with the key attributes of (i) significantly large thickness of the MHP single crystals by suppressing the transmitted light and (ii) the detector's limited dynamic range. Combining the theoretical and experimental characterizations, we clarify the significant role of the large thickness together with the limited sensitivity of the detector in promoting the well-known red shift of the absorption onset of the MHP single crystals. The observations evidently show that in some special circumstances, the acquired absorption spectrum cannot reliably represent the optical bandgap of MHP materials. This highlights some misinterpretations in the estimation of the narrower optical bandgap of the MHP single crystals from conventional optical methods, while the optical bandgap is an inherent property independent of the thickness. The proposed broad applications of the MHP single crystals are dictated by their fascinating properties, and therefore, a deep insight into these features should be considered besides device applications, because much of their property-function relationships are still ambiguous and a subject of debate.

Building a Charge Transfer Bridge between g-C3N4 and Perovskite with Molecular Engineering to Achieve Efficient Perovskite Solar Cells

Effective defect passivation and efficient charge transfer within polycrystalline perovskite grains and corresponding boundaries are necessary to achieve highly efficient perovskite solar cells (PSCs). Herein, focusing on the boundary location of g-C3N4 during the crystallization modulation on perovskite, molecular engineering of 4-carboxyl-3-fluorophenylboronic acid (BF) on g-C3N4 was designed to obtain a novel additive named BFCN. With the help of the strong bonding ability of BF with both g-C3N4 and perovskite and favorable intramolecular charge transfer within BFCN, not only has the crystal quality of perovskite films been improved due to the effective defects passivation, but the charge transfer has also been greatly accelerated due to the formation of additional charge transfer channels on the grain boundaries. As a result, the champion BFCN-based PSCs achieve the highest photoelectric conversion efficiency (PCE) of 23.71% with good stability.

Physical properties of ferromagnetic Mn-doped double perovskites (DPs) Cs2AgInCl/Br6 for spintronics and solar cell devices: DFT calculations

A computational framework based on density functional theory (DFT) has been effectively employed to investigate the wide-ranging physical characteristics of ferromagnetic manganese (Mn)-substituted double perovskites (DPs) with composition Cs2AgIn1-xMnxCl/Br6 (x = 0.0, 0.25). This research covers a systematic exploration of the mentioned DPs for potential applications in the domains of spintronics and energy conversion devices. The physics concerning ferromagnetic (FM) Cs2AgIn0.75Mn0.25Cl/Br6 DPs was studied computationally using the modified Becke-Johnson (mBJ-LDA) potential and the generalized gradient approximation (PBEsol GGA) method introduced by Perdew, Burke, and Ernzerhof. The structural, electronic, magnetic, and transport behavior of materials were investigated using these computations. Structural parameters for both perovskite materials were computed subsequent to their optimization in FM phase. According to evaluations of the electronic band structure and density of states (DOS), the incorporation of Mn ions into the host lattice causes exchange splitting induced by p-d hybridization, consequently stabilizing the FM state. Probing the sharing of magnetic moment, charge, and spin between the substituent cations and the host anions led to the comprehensive elaboration of this exchange splitting of bands. Important parameters such as exchange constants (N0α, N0β), and direct spin-exchange splitting Δx(d), support the stability of the FM state. Finally, we briefly explored the spin effect on other aspects of electronic transport, the Seebeck coefficient, and the power factor, using the conventional Boltzmann transport theory.

Mixing I and Br in Inorganic Perovskites: Atomistic Insights from Reactive Molecular Dynamics Simulations

All-inorganic halide perovskites have received a great deal of attention as attractive alternatives to overcome the stability issues of hybrid halide perovskites that are commonly associated with organic cations. To find a compromise between the optoelectronic properties of CsPbI3 and CsPbBr3, perovskites with CsPb(BrxI1-x)3 mixed compositions are commonly used. An additional benefit is that without sacrificing the optoelectronic properties for applications such as solar cells or light-emitting diodes, small amounts of Br in CsPbI3 can prevent the inorganic perovskite from degrading to a photo-inactive non-perovskite yellow phase. Despite indications that strain in the perovskite lattice plays a role in the stabilization of the material, a full understanding of such strain is lacking. Here, we develop a reactive force field (ReaxFF) for perovskites starting from our previous work for CsPbI3, and we extend this force field to CsPbBr3 and mixed CsPb(BrxI1-x)3 compounds. This force field is used in large-scale molecular dynamics simulations to study perovskite phase transitions and the internal ion dynamics associated with the phase transitions. We find that an increase of the Br content lowers the temperature at which the perovskite reaches a cubic structure. Specifically, by substituting Br for I, the smaller ionic radius of Br induces a strain in the lattice that changes the internal dynamics of the octahedra. Importantly, this effect propagates through the perovskite lattice ranging up to distances of 2 nm, explaining why small concentrations of Br in CsPb(BrxI1-x)3 (x ≤ 1/4) have a significant impact on the phase stability of mixed halide perovskites.

Group-IIIA element doped BaSnS2 as a high efficiency absorber for intermediate band solar cell from a first-principles insight

The quest for high-performance solar cell absorbers has garnered significant attention in the field of photovoltaic research in recent years. To overcome the Shockley-Queisser (SQ) limit of ∼31% for single junction solar cell and realize higher power conversion efficiency, the concept of an intermediate band solar cell (IBSC) has been proposed. This involves the incorporation of an intermediate band (IB) to assist the three band-edge absorptions within the single absorber layer. BaSnS2 has an appropriate width of its forbidden gap in order to host an IB. In this work, doping of BaSnS2 was studied based on hybrid functional calculations. The results demonstrated that isolated and half-filled IBs were generated with suitable energy states in the band gap region after group-IIIA element (i.e., Al, Ga, and In) doping at Sn site. The theoretical efficiencies under one sun illumination of 39.0%, 44.3%, and 39.7% were obtained for 25% doping concentration of Al, Ga, and In, respectively; thus, larger than the single-junction SQ-limit. Furthermore, the dopants have lower formation energies when substituting the Sn site compare to occupying the Ba and S sites, and that helps realizing a proper IB with three band-edge absorptions. Therefore, group-IIIA element doped BaSnS2 is proposed as a high-efficiency absorber for IBSC.

Synergetic interfacial conductivity modulation dictating hysteresis evolution in perovskite solar cells under operation

In this work, the configuration of compact TiO2 coating (c-TiO2) interface as electron transport layer (ETL) in giving rise to loss and gain of fill factor (FF) and therefore modulation of hysteresis behavior in perovskite solar cells (PSCs) is investigated. For this purpose, PSCs based on planar compact TiO2 (c-TiO2) as well as a scaffold-based architecture are studied. In the latter case c-TiO2 coats a hydrothermally grown titania nanorod scaffold. The results demonstrate that when c-TiO2 is used in planar configuration, FF considerably improves with prolonged light soaking which is in sharp contrast to what is observed for scaffold-based PSCs. Moreover, higher thickness of planar c-TiO2 is shown to be beneficial for sustaining FF in forward scan. Finally, through studying the intricate interfacial dynamics utilizing electrochemical impedance spectroscopy (EIS), it was concluded that for a PSC under operation, the cumulative effect of conductivity modulation at the perovskite with transport layer interfaces, for their respective charge carriers, determines the loss and gain in performance depending on scan rate, applied bias and prolonged light soaking. This work points towards multiple factors affecting PSC output, which could work either in confluence or against one another depending on the interfacial configuration of transport layers.

First-Principles Investigation into the Interaction of H2O with α-CsPbI3 and the Intrinsic Defects within It

CsPbI3 possesses three photoactive black phases (α, β, and γ) with perovskite structures and a non-photoactive yellow phase (δ) without a perovskite structure. Among these, α-CsPbI3 exhibits the best performance. However, it only exists at high temperatures and it tends to transform into the δ phase at room temperature, especially in humid environments. Therefore, the phase stability of CsPbI3, especially in humid environments, is the main obstacle to its further development. In this study, we studied the interaction of H2O with α-CsPbI3 and the intrinsic defects within it. It was found that the adsorption energy in the bulk is higher than that on the surface (-1.26 eV in the bulk in comparison with -0.60 eV on the surface); thus, H2O is expected to have a tendency to diffuse into the bulk once it adsorbs on the surface. Moreover, the intrinsic vacancy of VPb0 in the bulk phase can greatly promote H2O insertion due to the rearrangement of two I atoms in the two PbI6 octahedrons nearest to VPb0 and the resultant breaking of the Pb-I bond, which could promote the phase transition of α-CsPbI3 in a humid environment. Moreover, H2O adsorption onto VI+1 contributes to a further distortion in the vicinity of VI+1, which is expected to enhance the effect of VI+1 on the phase transition of α-CsPbI3. Clarifying the interaction of H2O with α-CsPbI3 and the intrinsic defects within it may provide guidance for further improvements in the stability of α-CsPbI3, especially in humid environments.

Progress and Application of Halide Perovskite Materials for Solar Cells and Light Emitting Devices

Halide perovskite materials have attracted worldwide attention in the photovoltaic area due to the rapid improvement in efficiency, from less than 4% in 2009 to 26.1% in 2023 with only a nanometer lever photo-active layer. Meanwhile, this nova star found applications in many other areas, such as light emitting, sensor, etc. This review started with the fundamentals of physics and chemistry behind the excellent performance of halide perovskite materials for photovoltaic/light emitting and the methods for preparing them. Then, it described the basic principles for solar cells and light emitting devices. It summarized the strategies including nanotechnology to improve the performance and the application of halide perovskite materials in these two areas: from structure-property relation to how each component in the devices affects the overall performance. Moreover, this review listed the challenges for the future applications of halide perovskite materials.

Scalable Lead Acetate-Based Perovskite Thin Films Prepared via Controlled Nucleation and Growth under Near Ambient Conditions

Lead acetate (PbAc2) is a promising precursor salt for large-scale production of perovskite solar cells, as its high solubility in polar solvents enables the use of scalable deposition methods such as inkjet printing and dip coating. In this study, uniform (40-230 nm) PbAc2 thin films were prepared via dip coating under near ambient lab conditions by tuning the PbAc2 precursor concentration. In a second step, these PbAc2 films were converted to methylammonium lead iodide (MAPI) perovskite by immersing them into methylammonium iodide (MAI) solutions. The nucleation and growth processes at play were controlled by altering key parameters, such as air humidity during the lead acetate deposition and MAI concentration when converting the PbAc2 film to MAPI. The research revealed that lead acetate is sensitive toward humidity and can undergo hydroxylation reactions affecting the reproducibility and quality of the produced solar cells. However, drying the PbAc2 films under low relative humidity (<1%) prior to conversion enables the production of high-quality MAPI films without the need of glovebox processing. Furthermore, SEM characterization revealed that the surface coverage of the MAPI film increased significantly with an increase of the MAI concentration at the conversion stage. The resulting morphology of the MAPI films can be explained by a standard nucleation and growth mechanism. Preliminary solar cells were produced using these MAPI films as the active layer. The best performing devices were obtained with a 140 nm thick lead acetate film converted to MAPI using a 12 mg/mL MAI solution, as these parameters resulted in a good surface coverage of the MAPI film. The results show that the methodology holds potential toward large-scale production of perovskite solar cells under near ambient conditions, which substantially simplifies the fabrication and lowers the production costs.

Effect of sub-bandgap defects on radiative and non-radiative open-circuit voltage losses in perovskite solar cells

The efficiency of perovskite solar cells is affected by open-circuit voltage losses due to radiative and non-radiative charge recombination. When estimated using sensitive photocurrent measurements that cover the above- and sub-bandgap regions, the radiative open-circuit voltage is often unphysically low. Here we report sensitive photocurrent and electroluminescence spectroscopy to probe radiative recombination at sub-bandgap defects in wide-bandgap mixed-halide lead perovskite solar cells. The radiative ideality factor associated with the optical transitions increases from 1, above and near the bandgap edge, to ~2 at mid-bandgap. Such photon energy-dependent ideality factor corresponds to a many-diode model. The radiative open-circuit voltage limit derived from this many-diode model enables differentiating between radiative and non-radiative voltage losses. The latter are deconvoluted into contributions from the bulk and interfaces via determining the quasi-Fermi level splitting. The experiments show that while sub-bandgap defects do not contribute to radiative voltage loss, they do affect non-radiative voltage losses.

Microstress for metal halide perovskite solar cells: from source to influence and management

The power conversion efficiency of metal halide perovskite solar cells (PSCs) has increased dramatically in recent years, but there are still major bottlenecks in the commercial application of such materials, including intrinsic instability caused by external stimuli such as water, oxygen, and radiation, as well as local stress generated inside the perovskite and external stress caused by poor interlayer contact. However, some crucial sources of instability cannot be overcome by conventional encapsulation engineering. Among them, the tensile strain can weaken the chemical bonds in the perovskite lattice, thereby reducing the defects formation energy and activation energy of ion migration and accelerating the degradation rate of the perovskite crystal. This review expounds the latest in-depth understanding of microstrain in perovskite film from the thermodynamic sources and influences on the perovskite physicochemical structure and photoelectric performance. Furthermore, it also summarizes the effective strategies for strain regulation and interlayer contact performance improvement, which are conducive to the improvement of photovoltaic performance and internal stability of PSCs. Finally, we present a prospective outlook on how to achieve more stable and higher efficiency PSCs through strain engineering.

Colloidal Aziridinium Lead Bromide Quantum Dots

The compositional engineering of lead-halide perovskite nanocrystals (NCs) via the A-site cation represents a lever to fine-tune their structural and electronic properties. However, the presently available chemical space remains minimal since, thus far, only three A-site cations have been reported to favor the formation of stable lead-halide perovskite NCs, i.e., Cs+, formamidinium (FA), and methylammonium (MA). Inspired by recent reports on bulk single crystals with aziridinium (AZ) as the A-site cation, we present a facile colloidal synthesis of AZPbBr3 NCs with a narrow size distribution and size tunability down to 4 nm, producing quantum dots (QDs) in the regime of strong quantum confinement. NMR and Raman spectroscopies confirm the stabilization of the AZ cations in the locally distorted cubic structure. AZPbBr3 QDs exhibit bright photoluminescence with quantum efficiencies of up to 80%. Stabilized with cationic and zwitterionic capping ligands, single AZPbBr3 QDs exhibit stable single-photon emission, which is another essential attribute of QDs. In particular, didodecyldimethylammonium bromide and 2-octyldodecyl-phosphoethanolamine ligands afford AZPbBr3 QDs with high spectral stability at both room and cryogenic temperatures, reduced blinking with a characteristic ON fraction larger than 85%, and high single-photon purity (g(2)(0) = 0.1), all comparable to the best-reported values for MAPbBr3 and FAPbBr3 QDs of the same size.

Strain Regulation and Defect Passivation of FA-Based Perovskite Materials for Highly Efficient Solar Cells

Formamidine lead triiodide (FAPbI3 ) perovskites have attracted increasing interest for photovoltaics attributed to the optimal bandgap, high thermal stability, and the record power conversion efficiency (PCE). However, the materials still face several key challenges, such as phase transition, lattice defects, and ion migration. Therefore, external ions (e.g., cesium ions (Cs+ )) are usually introduced to promote the crystallization and enhance the phase stability. Nevertheless, the doping of Cs+ into the A-site easily leads to lattice compressive strain and the formation of pinholes. Herein, trioctylphosphine oxide (TOPO) is introduced into the precursor to provide tensile strain outside the perovskite lattice through intermolecular forces. The special strain compensation strategy further improves the crystallization of perovskite and inhibits the ion migration. Moreover, the TOPO molecule significantly passivates grain boundaries and undercoordinated Pb2+ defects via the forming of P═O─Pb bond. As a result, the target solar cell devices with the synergistic effect of Cs+ and TOPO additives have achieved a significantly improved PCE of 22.71% and a high open-circuit voltage of 1.16 V (voltage deficit of 0.36 V), with superior stability under light exposure, heat, or humidity conditions.

Self-Healing Behavior of the Metal Halide Perovskites and Photovoltaics

Perovskite solar cells have achieved rapid progress in the new-generation photovoltaic field, but the commercialization lags behind owing to the device stability issue under operational conditions. Ultimately, the instability issue is attributed to the soft lattice of ionic perovskite crystal. In brief, metal halide perovskite materials are susceptible to structural instability processes, including phase segregation, component loss, lattice distortion, and fatigue failure under harsh external stimuli such as high humidity, strong irradiation, wide thermal cycles, and large stress. Developing self-healing perovskites to further improve the unsatisfactory operational stability of their photoelectric devices under harsh stimuli has become a cutting-edge hotspot in this field. This self-healing behavior needs to be studied more comprehensively. Therefore, the self-healing behavior of the metal halide perovskites and photovoltaics is classified and summarized in this review. By discussing recent advances, underlying mechanisms, strategies, and existing challenges, this review provides perspectives on self-healing of perovskite solar cells in the future.

Unraveling the Degradation Pathway of Inverted Perovskite Solar Cells Based on ISOS-D-1 Protocol

Perovskite solar cells (PSCs) have shown rapid development recently, whereas nonideal stability remains the chief obstacle toward commercialization. Thus, it is of utmost importance to probe the degradation pathway for the entire device. Here, the extrinsic stability of inverted PSCs (IPSCs) is investigated by using standard shelf-life testing based on the International Summit on Organic Photovoltaic Stability protocols (ISOS-D-1). During the long-term assessment of 1700 h, the degraded power conversion efficiency is mainly caused by the fill factor (53% retention) and short-circuit current density (71% retention), while the open-circuit voltage still maintains 97% of the initial values. Further absorbance evolution and density functional theory calculations disclose that the perovskite rear-contact side, in particular for the perovskite/fullerene interface, is the predominant degradation pathway. This study contributes to understanding the aging mechanism and enhancing the durability of IPSCs for future applications.

Recent Progress of Low-Toxicity Poor-Lead All-Inorganic Perovskite Solar Cells

Organic-inorganic hybrid perovskite solar cells (PSCs) have achieved an impressive certified efficiency of 25.7%, which is comparatively higher than that of commercial silicon solar cells (23.3%), showing great potential toward commercialization. However, the low stability and high toxicity due to the presence of volatile organic components and toxic metal lead in the perovskites pose significant challenges. To obtain robust and low-toxicity PSCs, substituting organic cations with pure inorganic cations, and partially or fully replacing the toxic Pb with environmentally benign metals, is one of the promising methods. To date, continuous efforts have been made toward the construction of highly performed low-toxicity inorganic PSCs with astonishing breakthroughs. This review article provides an overview of recent progress in inorganic PSCs in terms of lead-reduced and lead-free compositions. The physical properties of poor-lead all-inorganic perovskites are discussed to unveil the major challenges in this field. Then, it reports notable achievements for the experimental studies to date to figure out feasible methods for efficient and stable poor-lead all-inorganic PSCs. Finally, a discussion of the challenges and prospects for poor-lead all-inorganic PSCs in the future is presented.

Defect passivation in methylammonium/bromine free inverted perovskite solar cells using charge-modulated molecular bonding

Molecular passivation is a prominent approach for improving the performance and operation stability of halide perovskite solar cells (HPSCs). Herein, we reveal discernible effects of diammonium molecules with either an aryl or alkyl core onto Methylammonium-free perovskites. Piperazine dihydriodide (PZDI), characterized by an alkyl core-electron cloud-rich-NH terminal, proves effective in mitigating surface and bulk defects and modifying surface chemistry or interfacial energy band, ultimately leading to improved carrier extraction. Benefiting from superior PZDI passivation, the device achieves an impressive efficiency of 23.17% (area ~1 cm2) (low open circuit voltage deficit ~0.327 V) along with superior operational stability. We achieve a certified efficiency of ~21.47% (area ~1.024 cm2) for inverted HPSC. PZDI strengthens adhesion to the perovskite via -NH2I and Mulliken charge distribution. Device analysis corroborates that stronger bonding interaction attenuates the defect densities and suppresses ion migration. This work underscores the crucial role of bifunctional molecules with stronger surface adsorption in defect mitigation, setting the stage for the design of charge-regulated molecular passivation to enhance the performance and stability of HPSC.

Unraveling radiation damage and healing mechanisms in halide perovskites using energy-tuned dual irradiation dosing

Perovskite photovoltaics have been shown to recover, or heal, after radiation damage. Here, we deconvolve the effects of radiation based on different energy loss mechanisms from incident protons which induce defects or can promote efficiency recovery. We design a dual dose experiment first exposing devices to low-energy protons efficient in creating atomic displacements. Devices are then irradiated with high-energy protons that interact differently. Correlated with modeling, high-energy protons (with increased ionizing energy loss component) effectively anneal the initial radiation damage, and recover the device efficiency, thus directly detailing the different interactions of irradiation. We relate these differences to the energy loss (ionization or non-ionization) using simulation. Dual dose experiments provide insight into understanding the radiation response of perovskite solar cells and highlight that radiation-matter interactions in soft lattice materials are distinct from conventional semiconductors. These results present electronic ionization as a unique handle to remedying defects and trap states in perovskites.

Novel Strategy for High Efficient and Stable Perovskite Solar Cells through Atomic Layer Deposition

The perovskite material has demonstrated conceivable potential as an absorbing material of solar cells. Although the power conversion efficiency of the device based on perovskite has rapidly come to 26%, there are still many factors that affect the further improvement of the photoelectric conversion efficiency. Interface defects are the dominating concern that influence carrier transportation and stability. Here, we report a novel strategy where B2O3 is deposited on the fresh perovskite film by atomic layer deposition technology. The organic atmosphere during atomic layer deposition can effectively regulate the crystallization kinetics of perovskites and promote crystal growth. The B2O3 adsorbed on the perovskite light-absorption layer can effectively reduce the electropositive defects on the surface of the perovskite, such as uncoordinated Pb2+ and I vacancies due to the electron-donating properties of the side O atoms in B2O3. Consequently, the power conversion efficiency of the perovskite solar cell after B2O3 treatment increases to 21.78% from 18.89%. Simultaneously, B2O3 can improve the stability of devices.

Optoelectronic synapses based on a triple cation perovskite and Al/MoO3 interface for neuromorphic information processing

Optoelectronic synaptic transistors are attractive for applications in next-generation brain-like computation systems, especially for their visible-light operation and in-sensor computing capabilities. However, from a material perspective, it is difficult to build a device that meets expectations in terms of both its functions and power consumption, prompting the call for greater innovation in materials and device construction. In this study, we innovatively combined a novel perovskite carrier supply layer with an Al/MoO3 interface carrier regulatory layer to fabricate optoelectronic synaptic devices, namely Al/MoO3/CsFAMA/ITO transistors. The device could mimic a variety of biological synaptic functions and required ultralow-power consumption during operation with an ultrafast speed of >0.1 μs under an optical stimulus of about 3 fJ, which is equivalent to biological synapses. Moreover, Pavlovian conditioning and visual perception tasks could be implemented using the spike-number-dependent plasticity (SNDP) and spike-rate-dependent plasticity (SRDP). This study suggests that the proposed CsFAMA synapse with an Al/MoO3 interface has the potential for ultralow-power neuromorphic information processing.

Green Anisole as Antisolvent in Planar Triple-Cation Perovskite Solar Cells with Varying Cesium Concentrations

The feasibility of replacing toxic chlorobenzene antisolvents with environmentally friendly anisole in the fabrication of planar triple-cation perovskite solar cells was explored here. The successful integration of anisole not only ensures comparable device performance but also contributes to the development of more sustainable and green fabrication processes for next-generation photovoltaic technologies. Nevertheless, to ensure the possibility of achieving well-functioning unencapsulated devices whose working operation depends on outdoor atmospheric conditions, we found that adjusting the cesium concentrations in the perovskite layers enabled the electrical characterization of efficient devices even under high relative humidity conditions (more than 40%). We found that 10% of CsI in the precursor solution will make devices with low hysteresis indexes and sustained performance stability over a 90-day period both with cholorobenzene and anisole antisolvent. These results further confirm that green anisole can replace chlorobenzene as an antisolvent.

A Practical Approach Toward Highly Reproducible and High-Quality Perovskite Films Based on an Aging Treatment

Solution processing of hybrid perovskite semiconductors is a highly promising approach for the fabrication of cost-effective electronic and optoelectronic devices. However, challenges with this approach lie in overcoming the controllability of the perovskite film morphology and the reproducibility of device efficiencies. Here, a facile and practical aging treatment (AT) strategy is reported to modulate the perovskite crystal growth to produce sufficiently high-quality perovskite thin films with improved homogeneity and full-coverage morphology. The resulting AT-films exhibit fewer defects, faster charge carrier transfer/extraction, and suppressed non-radiative recombination compared with reference. The AT-devices achieve a noticeable improvement in the reproducibility, operational stability, and photovoltaic performance of devices, with the average efficiency increased by 16%. It also demonstrates the feasibility and scalability of AT strategy in optimizing the film morphology and device performance for other perovskite components including MAPbI3 , (MAPbBr3 )15 (FAPbI3 )85 , and Cs0.05 (MAPbBr3 )0.17 (FAPbI3 )0.83 . This method opens an effective avenue to improve the quality of perovskite films and photovoltaic devices in a scalable and reproducible manner.

Perovskite/silicon tandem solar cells-compositions for improved stability and power conversion efficiency

Perovskite/Silicon Tandem Solar Cells (PSTSCs) represent an emerging opportunity to compete with industry-standard single junction crystalline silicon (c-Si) solar cells. The maximum power conversion efficiency (PCE) of single junction cells is set by the Shockley-Queisser (SQ) limit (33.7%). However, tandem cells can expand this value to ~ 45% by utilising two stacked solar cells to harvest the solar spectrum more efficiently. 33.9% PCE has already been achieved with PSTSCs. This perspective analyses recent advances in PSTSC technology, with an emphasis on optimal perovskite composition, the problem and mitigation of light-induced halide phase segregation, self-assembled hole transporting monolayers and additives that can improve and stabilise the perovskite. Top-performing compositions show three cationic components (Cs+, FA+, Pb2+) and three anionic (I-, Br-, Cl-) with a bandgap between 1.55 and 1.77 eV and a theoretical maximum of 1.73 eV (717 nm). Anionic additives such as (Br3)- and SCN- reduce trap states and segregation. 2D-perovskite grain boundary interfaces are created with cationic alkylammonium additives such as methyl-phenethylammonium (MPEA) and result in improved performance. 2-, 3- or 4-terminal devices with a (partly) textured silicon heterojunction (SHJ) bottom cell are ideal. An ultra-thin interfacial recombination layer (~ 5 nm) of indium tin oxide (ITO) or indium zinc oxide (IZO) containing a carbazole-based hole transporting self-assembled monolayer (Me-4PACz) is used for optimal 2-terminal tandem devices.