Adsorption behavior of arsenicals on MIL-101(Fe): The role of arsenic chemical structures

Zero-valent bimetallic catalyst/absorbent for simultaneous facilitation of MgSO3 oxidation and arsenic uptake

Cobalt (Co)-based catalysts can efficiently reduce the heat waste from sulfate concentration by enhancing sulfite oxidation during wet flue gas desulfurization system. However, arsenic (As) can poison such catalysts and migrate into the sulfate by-products, resulting in severe secondary pollution. In this study, a zero-valent Co/iron (Fe)-based nanoparticle (NZV-Co₂Fe₁) was fabricated and applied as a bifunctional catalyst/adsorbent. The catalytic stability of the Co-based catalyst was enhanced by the introduction of Fe because the poisonous effect of As was substantially suppressed because of the high adsorption capacity of Fe for As. Compared with the noncatalytic benchmark, the presence of 0.5 g/L NZV-Co₂Fe₁ can increase the rate of MgSO₃ oxidation by approximately 12-fold even at a high concentration of As (2.5 mg/L). The Langmuir model was fitted to the As adsorption isotherms, indicating that As uptake is a single-layer adsorption process. The pseudo-second-order kinetic model indicated that As was removed through chemisorption. The oxidation pathway of As(III) involves reactive radicals (mainly OH, SO₄^- and SO₅^-) and ligand-to-metal charge transfer between SO₃^2- and Co²⁺. The availability of MgSO₃ improved the removal efficiency at high concentrations of As(III) (1 mg/L). These results indicate that using NZV-Co₂Fe₁ as a catalyst to purify the by-products of flue gas desulfurization can effectively prevent secondary pollution.

MIL-101-Cr/Fe/Fe-NH2 for Efficient Separation of CH4 and C3H8 from Simulated Natural Gas

Adsorptive separation based on porous solid adsorbents has emerged as an excellent effective alternative to energy-intensive conventional separation methods in a low energy cost and high working capacity manner. However, there are few stable mesoporous metal-organic frameworks (MOFs) for efficient purification of methane from other light hydrocarbons in natural gas. Herein, we report a series of stable mesoporous MOFs, MIL-101-Cr/Fe/Fe-NH2, for efficient separation of CH4 and C3H8 from a ternary mixture CH4/C2H6/C3H8. Experimental results show that all three MOFs possess excellent thermal, acid/basic, and hydrothermal stability. Single-component adsorption suggested that they have high C3H8 adsorption capacity and commendable selectivity for C3H8 and C2H6 over CH4. Transient breakthrough experiments further certified the ability of direct separation of CH4 from simulated natural gas and indirect recovery of C3H8 from the packing column. Theoretical calculations illustrated that the van der Waals force proportional to the molecular weight is the key factor and that the structural integrity and defect can impact separation performances.

Application of iron oxyhydroxide to stabilize As(V) and phenylarsonic acid in contaminated soil: adsorption and the relevance to bioavailability

The leaked arsenic-containing chemical warfare agent has caused severe contamination to the surrounding soil and water. In this study, iron oxyhydroxide (FeOOH) with different crystalline phases was used to stabilize arsenic. The results revealed that α/β- mixed crystalline iron oxyhydroxide (MIX-FeOOH) had better adsorption performance for As(V) and phenylarsonic acid (PAA) in water, with the adsorption capacity 71.4 and 54.7 mg g^-1 at 50 mg L^-1 equilibrium concentration, respectively. The adsorption mechanism was proved to be inner-sphere complexation, electrostatic interaction, and hydrogen bonding. Meanwhile, the oxygen vacancies on FeOOH could increase the isoelectric point and further promote the adsorption capacity through inner-sphere complexation. In arsenic contaminated soil, when the addition amount of MIX-FeOOH was 5%, the bioavailability of arsenic in As(V) and PAA contaminated soil was significantly reduced after 28 days, and the stabilization rate reached 77.2% and 76.5%, respectively. After 7 days of remediation, 17.1% and 11.9% of the most mobile portions of As(V) and PAA could be converted into poorly mobile portions, respectively. The stabilization mechanism includes inner-sphere complexation, mineral adsorption, and coprecipitation. In summary, this study can provide technical support for the remediation practice of arsenic-containing warfare agent contaminated sites.

Recent developments in MOF and MOF based composite as potential adsorbents for removal of aqueous environmental contaminants

With the growth of globalization which has been the primary cause of water pollution, it is utmost necessary for us living being to have access to clean water for the purpose of drinking, washing and various other useful applications. With the purpose of future security and to restore our ecological balance, it is essential to give much significance towards the removal of unwanted toxic contaminants from our water resources. In this regard adsorptive removal of toxic pollutants from wastewater with porous adsorbent is regarded as one of the most promising way for water decontamination process. Metal organic frameworks (MOFs) comprising of uniformly arranged pores, abundant active sites and containing an easily tunable structure has aroused as a promising material for adsorbent to remove the unwanted contaminants from water sources. The adsorption of pollutants by the different MOFs surface are driven by various interactions including π-π, acid-base, electrostatic and H-bonding etc. On the other hand, the removal of various contaminants by MOFs is influenced by various factors including pH, temperature and initial concentration. In this review we will specifically discuss the adsorptive removal of different organic and inorganic pollutants present in our water systems with the use of MOFs as adsorbent along with the various factors and interaction mechanism manipulating the adsorption behaviour.

Machine learning approaches for predicting arsenic adsorption from water using porous metal-organic frameworks

Arsenic in drinking water is a serious threat for human health due to its toxic nature and therefore, its eliminating is highly necessary. In this study, the ability of different novel and robust machine learning (ML) approaches, including Light Gradient Boosting Machine (LightGBM), Extreme Gradient Boosting, Gradient Boosting Decision Tree, and Random Forest was implemented to predict the adsorptive removal of arsenate [As(V)] from wastewater over 13 different metal–organic frameworks (MOFs). A large experimental dataset was collected under various conditions. The adsorbent dosage, contact time, initial arsenic concentration, adsorbent surface area, temperature, solution pH, and the presence of anions were considered as input variables, and adsorptive removal of As(V) was selected as the output of the models. The developed models were evaluated using various statistical criteria. The obtained results indicated that the LightGBM model provided the most accurate and reliable response to predict As(V) adsorption by MOFs and possesses R², RMSE, STD, and AAPRE (%) of 0.9958, 2.0688, 0.0628, and 2.88, respectively. The expected trends of As(V) removal with increasing initial concentration, solution pH, temperature, and coexistence of anions were predicted reasonably by the LightGBM model. Sensitivity analysis revealed that the adsorption process adversely relates to the initial As(V) concentration and directly depends on the MOFs surface area and dosage. This study proves that ML approaches are capable to manage complicated problems with large datasets and can be affordable alternatives for expensive and time-consuming experimental wastewater treatment processes.

Tuning the structure of cerium-based metal-organic frameworks for efficient removal of arsenic species: The role of organic ligands

The ability of organic ligands to change the structure of metal-organic frameworks (MOFs) in nature and influence their adsorption efficiency for arsenic species is enormous. The current work was designed to investigate the adsorption performance of cerium-based MOFs with tunable structures through the use of organic ligands (Ce-MOF-66 and Ce-MOF-808) towards arsenic species from water. The structural features of Ce-MOF-66 and Ce-MOF-808 with varying crystallinity, morphology, particle size, and surface area are considerably altered by organic ligands tuning, resulting in clearly distinct arsenate (As (V)) and arsenite (As (III)) adsorption capabilities. The experimental results showed that the Langmuir adsorption capacities of As (V) by Ce-MOF-66 and Ce-MOF-808 reached 355.67 and 217.80 mg/g, respectively, while for As (III) were 5.52 and 402.10 mg/g for Ce-MOF-66 and Ce-MOF-808, respectively. Except for the impact of PO₄^3- on As (V), co-existing ions had no significant influence on adsorption, illustrating the high selectivity. Furthermore, to understand the structure and adsorption mechanism, two adsorbents were characterized by powder X-ray diffraction, scanning electron microscopy, thermogravimetric analysis, specific surface area, Fourier transform infrared and X-ray photoelectron spectroscopy, in which identified that unsaturated sites and ligand exchange were the main adsorption mechanisms of As (V) and As (III). Overall, this research presents a novel approach for developing high-performance Ce-derived MOFs adsorbents to capture arsenic species.

Effects of High Gamma Doses on the Structural Stability of Metal-Organic Frameworks

Four different MOFs were exposed to γ rays by a cobalt-60 source reaching a maximum dose of 5 MGy. The results showed that the MIL-100 (Cr) and MIL-100 (Fe) did not exhibit obvious structural damage, suggesting their excellent radiation stability. MIL-101 (Cr) showed good radiation stability up to 4 MGy, but its structure started degrading with increasing radiation dose. Furthermore, the results showed that the structure of AlFu MOFs started to decompose at a gamma dose of 1 MGy, exhibiting a much lower tolerance to γ radiation. At this radiation energy, the dominant interaction of the gamma-ray with MOFs is the Compton effect and the radiation stability of MOFs can be improved by prolific aromatic linkers, high linker connectivity, and good crystallinity. The results of this study indicate that MIL-100 and MIL-101 MOFs have a good potential to be employed in nuclear applications, where relatively high radiation doses play a role, for example, nuclear waste treatment and radionuclides production.

Immobilization mechanism of antimony by applying zirconium-manganese oxide in soil

Antimony (Sb) accumulation in soil poses great potential risk to ecological environment, and its mobilization, transformation and bioavailability are controlled by its fractions and species. Hence, it is important to develop functional materials with both adsorption and oxidation that achieve detoxification and control the mobilization of Sb. In this study, the synthesized zirconium‑manganese oxide (ZrMn) could extremely promoted the transformation of antimonite [Sb(III)] to antimonate [Sb(V)], induced the bioavailable Sb shift to well-crystallized (hydr)oxides of Mn and residual fractions, and further reduced mobility and bioavailability Sb in soil. The sorption of ZrMn to Sb(III) and antimonate Sb(V) were affected by interfering ions, and to Sb(III) was a heterogeneous adsorption process. Spectroscopic characterization of XPS and FTIR suggested exchange between the hydroxyl groups and Sb was crucial in its retain and forming an electronegative inner-sphere mononuclear or binuclear bridging compound. The oxidation induced the transformation of Mn species in ZrMn, generated Mn(II) and Mn(III) exposing more reactive sites conducive to oxidation and adsorption, thus Mn oxides has a higher adsorption capacity for Sb(III). However, the Zr oxides of ZrMn presented adsorption rather than oxidation. The application of ZrMn could realize the dual effect of Sb oxidation detoxification and adsorption immobilization in soil, which provided references for Sb contaminated soil remediation.

MIL series of metal organic frameworks (MOFs) as novel adsorbents for heavy metals in water: A review

With large specific surface area, abundant adsorption sites, flexible pore structure, and good water stability, Materials of Institute Lavoisier frameworks (MILs) have attracted increasing attention as effective environmental adsorbents. This review systematically analyzes and recapitulates recent progress in the synthesis and application of MIL-based adsorbents for the removal of aqueous heavy metal ions. Commonly used solvothermal, microwave, electrochemical, ultrasonic, and mechanochemical syntheses of MILs are first summarized and compared. Instead of focusing on adsorption process parameters, adsorption performances and governing mechanisms of virgin MILs, functional MILs, MIL-based composites, and carbonized MILs to representative metal(loid) ions (chromium, arsenic, lead, cadmium, and mercury) in water under various conditions are then systematically reviewed and discussed. In the end, this work also outlines prospects and future directions to promote the applications of MILs in treating heavy metal contaminated water.

New insights into the selective adsorption mechanism of cationic and anionic dyes using MIL-101(Fe) metal-organic framework: Modeling and interpretation of physicochemical parameters

In the current study, iron-based metal organic framework (MOF) MIL-101(Fe) was successfully prepared via a facile solvothermal method. The as-synthesized MIL-101(Fe) was characterized by XRD, FE-SEM, FTIR, TGA and zeta potential techniques, and then employed as an adsorbent for methyl orange (MO) and methylene blue (MB) dyes. The adsorbed quantities of MO (1067 to 831 mg/g) were higher than those of MB (402 to 353 mg/g) indicating the high selectivity of MIL-101(Fe) towards the anionic dye at all temperatures (20-60 °C). Adsorption processes of MO and MB followed the pseudo-second order kinetics and the Langmuir equilibrium model. The interaction mechanism at a molecular level was analyzed and deeply interpreted via the advanced multilayer adsorption model. Steric parameters indicated that MO molecular aggregation (n) was 0.95-1.33 thus signifying the presence of multi-docking and multi-interactions mechanisms. The aggregated number of MB was superior to unity (i.e., n = 1.17-1.78) suggesting a vertical adsorption position and a multi-interactions mechanism at all operating temperatures. The density of MIL-101(Fe) active sites (D_{M =} 77.33-52.38 mg/g for MB and 149.91-107.07 for MO) and the total adsorbed dye layers (N_t = 3.12-2.49 for MB and 5.36-3.67 for MO) resulted in improving the adsorption capacities of MO dye. The adsorption energies ranged from 8.89 to 33.73 kJ/mol and they displayed that MO and MB uptake processes were exothermic controlled by physical interactions at all temperatures. Regeneration results indicated that this adsorbent can be reutilized without a significant loss in its removal efficiency after five adsorption-desorption cycles. Overall, the adsorption capacity, chemical stability, and regeneration performance of MIL-101(Fe) support its application as a very promising adsorbent for the removal of organic hazardous pollutants from water.

Preparation of magnetic metal-organic framework MIL-101(Fe) and its application in the extraction of anthraquinones in rhubarb

In this work, a magnetic octahedral metal organic framework (Fe₃ O₄ @NH₂ -MIL-101(Fe)) was synthesized for the magnetic solid phase extraction of three anthraquinones, including aloe-emodin, emodin, and physcion, in rhubarb. The Fe₃ O₄ @NH₂ -MIL-101(Fe) exhibited a high specific surface area of 259.2 m² /g with an average pore size of 6.0 nm and a high magnetic responsivity of 23.4 emu/g, which may be used as an adsorbent for rapid preconcentration and separation of target analytes. The main parameters for magnetic solid phase extraction of anthraquinones, including the amount of adsorbent, extraction time, extraction temperature, extraction pH, elution solvent, and elution time, were systematically optimized. The whole extraction process required a very low amount of adsorbent and a small volume of the sample. Besides, under the optimized conditions, the method showed satisfactory spiked recovery for anthraquinones in the range of 93.3%-109.1%, and the LODs were 1.7-3.4 ng/mL. The RSDs for intra- and inter- day precision were 0.2%-1.3% and 0.2%-0.6%, respectively. The experimental results indicate that the developed method is feasible for the analysis of anthraquinones in rhubarb. This article is protected by copyright. All rights reserved.

Enhanced removal of P(V), Mo(VI) and W(VI) generated oxyanions using Fe-MOF as adsorbent from hydrometallurgical waste liquid: Exploring the influence of ionic polymerization

Environmentally hazardous P(V), Mo(VI) and W(VI) generated oxyanions exist widely in the waste liquid of nonferrous hydrometallurgy. In this work, Fe-MOF material was simply prepared via solvothermal synthesis and then used as an adsorbent to remove P(V), Mo(VI) and W(VI) oxyanions from hydrometallurgical waste liquid. Several important parameters, including solution pH, oxyanion concentration, contact time, adsorbent amount, temperature and coexistent heavy metal ions, were systematically investigated. The results demonstrate that adsorption process was almost pH-independent over a broad range of pH 3.0-10.0. The adsorption efficiency was strongly associated with the chemical species of oxyanions. The higher polymerisation degree of oxyanions was more favourable for removal efficiency. Additionally, the maximum removal efficiencies for P(V), Mo(VI) and W(VI) oxyanions under optimum conditions were approximately 100%. Furthermore, the adsorption kinetics and isotherms of oxyanions on the adsorbent separately belonged to the pseudo-second-order and Langmuir isotherm models. XPS analysis revealed that inner-sphere complexation played a dominant role in the adsorption removal process. Fe-MOFs with pH-independent properties, abundant binding sites and high stability are prospective adsorbents for treating waste liquids in the hydrometallurgical industry.

CTAB-functionalized δ-FeOOH for the simultaneous removal of arsenate and phenylarsonic acid in phenylarsenic chemical warfare

This study prepared a cetyltrimethylammonium bromide (CTAB) functionalized δ-FeOOH using the coprecipitation method to remove arsenate and phenylarsonic acid in water polluted by phenylarsonic chemical warfare agents. Under neutral conditions, the adsorption capacity for arsenate and phenylarsonic acid was 45.7 and 85.3 mg g^-1, respectively. The adsorption process conformed to the pseudo-second-order kinetics and Freundlich isothermal adsorption model, and the adsorption was spontaneous and endothermic. The CTAB-functionalized δ-FeOOH could effectively resist the interference of coexisting anions except for CO₃^2-, SiO₃^2- and PO₄^3-. Furthermore, the adsorption mechanism was proposed by combining the adsorption experimental results, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and density functional theory analyses. The results showed that the adsorption of arsenate by the CTAB-functionalized δ-FeOOH was mainly through the formation of bidentate-dinuclear inner-sphere complexes and electrostatic interactions. While for phenylarsonic acid, the formation of monodentate-mononuclear inner-sphere complexes on (100) and (110) crystal facets, and the formation of bidentate-dinuclear inner-sphere complexes on the (002) crystal facet, as well as hydrogen bonding, electrostatic interaction, and π-hydrophobic interaction between organic compounds were the primary mechanism. Moreover, the CTAB-functionalized δ-FeOOH could maintain about 60% of the adsorption capacity for the two pollutants after five cycles. Overall, CTAB-functionalized δ-FeOOH has good potential for the remediation of inorganic and organic arsenic-contaminated water bodies.

Physicochemical Modeling of the Adsorption of Pharmaceuticals on MIL-100-Fe and MIL-101-Fe MOFs

The adsorption of naproxen (NAP), diclofenac (DFC), and acetaminophen (APAP) molecules from aqueous solutions using MIL-100-Fe and MIL-101-Fe metal organic frameworks (MOFs) has been analyzed and modeled. Adsorption isotherms of these pharmaceuticals were experimentally quantified at 30 and 40°C and pH 7. Textural parameters and surface chemistry of these MOFs were analyzed, and results were utilized to explain the pharmaceutical adsorption mechanism. Density Functional Theory (DFT) calculations were performed to understand the reactivity of pharmaceutical molecules, and a statistical physics model was employed to calculate the main physicochemical parameters related to the adsorption mechanism. Results showed that the adsorption of these pharmaceuticals on MOFs was multimolecular and exothermic. Both MOFs displayed the highest adsorption capacities, up to 2.19 and 1.71 mmol/g, for NAP and DFC molecules, respectively. MIL-101-Fe showed better pharmaceutical adsorption properties than MIL-100-Fe due to its highest content of Fe-O clusters and mesopore volume. Adsorption mechanism of these organic molecules could involve hydrogen bond, van der Waals forces, and electrostatic interactions with MOF surfaces. In particular, MIL-101-Fe MOF is a promising material to prepare composites with competitive adsorption capacities for facing the water pollution caused by pharmaceutical compounds.

Synthesis, modifications and applications of MILs Metal-organic frameworks for environmental remediation: The cutting-edge review

Ever-increasing anthropogenic activities are radically deteriorating the environment by causing severe pollution. Thus, curtailing the environmental pollution and promotion of sustainable development, are the hot issues confronted by scientists in this modern era. Metal-organic frameworks (MOFs) have been highly recognized as emerging promising materials for environmental remediation due to their versatile structure and extraordinary properties. Among them, MILs (MIL = Matérial Institute of Lavoisier) are the series of MOFs mostly known for their incredible stability, unique tailorable pore structures, and astounding versatile environmental applications. Their exclusive physiochemical properties and multifunctionality make them proficient for a wide range of pollutants removal in the exposure of versatile harsh environments, compared to other MOFs. This piece of research summarizes the state-of-the-art of development of MILs on the broad spectrum, highlighting their specificities, such as synthesis techniques, modifications and applications for environmental remediation. However, MILs wonderful properties and extraordinary applications in multiple fields, their deployment on practical and commercial-scale pollutants remediation is hindered by insufficient scientific research on underlying mechanisms and relationships. Henceforth, this review not only signifies the emerging importance of MILs for environmental applications but also indicates the urgency to maximize the scientific research for exploitation of MOFs on a practical level and promotion of green technologies for environmental remediation.

Research progress of metal organic frameworks and their derivatives for adsorption of anions in water: A review

Anion pollution in water has become a problem that cannot be ignored. The anion concentration should be controlled below the national emission standard to meet the demand for clean water. Among the methods for removing excess anions in water, the adsorption method has a unique removal performance, and the core of the adsorption method is the adsorbent. In recent years, the emerging metal-organic frameworks (MOFs) have the advantages of adjustable porosity, high specific surface area, diverse functions, and easy modification. They are very competitive in the field of adsorption of liquid anions. This article focuses on the adsorption of fluoride, arsenate, chromate, radioactive anions (ReO₄^-, TcO₄^-, SeO₄^2-/SeO₃^2-), phosphate ion, chloride ion, and other anions by MOFs and their derivatives. The preparation methods of MOFs are introduced in turn, the application of different types of metal-based MOFs to adsorb various anions were discussed in categories with their crystal structure and functional groups. The influence on the adsorption of anions is analyzed, including the more common and special adsorption mechanisms, adsorption kinetics and thermodynamics, and regeneration performance are briefly described. Finally, the current situation of MOFs adsorption of anions is summarized, and the outlook for future development is summarized to provide my own opinions for the practical application of MOFs.

Cerium-doped MIL-101-NH2(Fe) as superior adsorbent for simultaneous capture of phosphate and As(V) from Yangzonghai coastal spring water

A series of novel cerium-doped MIL-101-NH₂ materials were synthesized using the solvothermal method for the simultaneous efficient removal of phosphate and As(V). According to the characterization results, cerium was successfully loaded onto MIL-101-NH₂ and that Ce-MOFs might be generated during the loading process, which modified the crystal structure of MIL-101-NH₂ and resulted in MOFs with different microstructures. In single-uptake systems containing only phosphate or As(V), isothermal adsorption experiments showed that 1Ce-MIL-101-NH₂ exhibited better adsorption properties of phosphate and As(V) than MIL-101-NH₂. Furthermore, the uptake amounts of phosphate and As(V) reached 341.5 mg/g and 249 mg/g, respectively. Superior uptake amounts for binary phosphate (167.36 mg/g) and As(V) (87.55 mg/g) were achieved with 1Ce-MIL-101-NH₂. Kinetic experiments revealed a higher uptake rate of phosphate than of As(V). FT-IR and XPS analyses showed that the main mechanism for the removal of phosphate and As(V) from water by 1Ce-MIL-101-NH₂ was the formation of an Fe/CeOP inner complex through ligand complexation and electrostatic attraction. Furthermore, 1Ce-MIL-101-NH₂ exhibited high selectivity and excellent efficiency in removing phosphate and As(V) in contaminated spring water in the presence of competing anions; this further confirms the application potential of the novel adsorbent.

A heterogeneous peroxymonosulfate catalyst built by Fe-based metal-organic framework for the dye degradation

The regulatory control on dyes is an important issue, as their discharge into the environment can pose significant risks to human health. MIL-101(Fe) prepared by a solvothermal method was used as a catalyst to generate sulfate (SO₄^•-) and hydroxyl (HO^•) radicals from peroxymonosulfate (PMS) for the treatment of orange G (OG). The structural properties of MIL-101(Fe) were assessed by a number of characterization approaches (e.g., Fourier-transform infrared spectroscopy). The factors controlling the removal of OG were explored by a response surface methodology with central composite design (RSM-CCD) plus adaptive neuro-fuzzy inference system (ANFIS). The synthetized MIL-101(Fe) had uniform octahedral nanocrystals with rough surfaces and porous structures. The maximum catalytic removal efficiency of OG with MIL-101(Fe)/PMS process was 74% (the final concentration of Fe²⁺ as 0.19 mg/L and reaction rate of 434.2 μmol/g/h). The catalytic removal of OG could be defined by the non-linear kinetic models based on RSM. The OG removal efficiency declined noticeably with the addition of radical scavengers such as ethanol (EtOH) and tert-butanol (TBA) along with some mineral anions. Accordingly, MIL-101(Fe)/PMS is identified as an effective remediation option for the dyes based on advanced oxidation process (AOPs) based on high treatment efficiency at low dosage of low cost catalyst.

Effectively remove p-arsanilic acid from water over amphiphilic amino modified collagen fiber

Efficient and rapid removal of p-arsanilic acid (p-ASA) in water is very important in environmental protection and human health, however it is still a severe challenge in actual engineering. Herein, a novel sorbent (CF-PEI) was successfully fabricated by simply modifying the amphiphilic skin collagen fiber (CF) substrate with Polyethylenimine (PEI). The as-prepared CF-PEI exhibits high-efficiency adsorption for negatively charged p-ASA with aromatic rings due to the introduction of amino groups and the existence of hydrophobic bands, and the maximum adsorption capacity of CF-PEI for p-ASA was high up to 285.71 mg g^-1. In addition, the adsorption mechanism of CF-PEI on p-ASA mainly includes electrostatic interaction, hydrogen bond and amphiphilicity. The multi-level all-fiber structure of CF makes it mainly focus on surface mass transfer with short mass transfer distance, and its capillary drainage effect can realize large flow and rapid separation. CF-PEI based on CF can realize the ability to separate low-concentration p-ASA with high flow rate and high efficiency. The effective processing volume was 12.5 L g^-1 when the separation flux reached as high as 9931.27 L m^-2 h^-1. Notably, the p-ASA adsorbed on CF-PEI was almost completely eluted by NaOH (0.5 mol L^-1). The adsorbent is convenient to prepare, recyclable, high in efficiency, and has a great application prospect in removing organic micro-pollutants.

Adsorption and convenient ELISA detection of sulfamethazine in milk based on MOFs pretreatment

Metal-organic frameworks (MOFs) has excellent adsorption performance, herein, three kinds of common MOFs were used for the adsorption of sulfamethazine (SM₂) in milk, then enzyme-linked immunosorbent assay (MOF-ELISA) was established. Firstly, NH₂-UiO-66, NH₂-MIL-101, and ZIF-8 were successfully prepared and their adsorption characteristics for SM₂ were investigated. The kinetic models of the three MOFs were more in line with the pseudo-second-order adsorption kinetics, and the saturated adsorption capacity of NH₂-UiO-66, NH₂-MIL-101, and ZIF-8 for SM₂ at 298 K were 139.64, 29.98, and 36.5 mg/g, respectively. Using three different MOFs as adsorbents, the pretreatment of milk samples could be completed within 1 h, the half inhibitory concentrations (IC₅₀) of MOF-ELISA were 1.26, 1.86 and 2.74 ng/mL, the limit of detections (LOD) were 0.05, 0.12, and 0.19 ng/mL and the recovery rate were from 82.30% to 105.62% with the intra-day coefficient of variations (CVs) below 5.81% and inter-day CVs below 7.21%. Detection results showed good correlations with LC-MS/MS (R² > 0.99), indicated that MOFs could effectively eliminate the interference of sample matrix, and has the potential to become a general pretreatment method for the detection of various matrices residues in food safety monitoring.

Iron-based metal-organic framework: Synthesis, structure and current technologies for water reclamation with deep insight into framework integrity

Water is a supreme requirement for the existence of life, the contamination from the point and non-point sources are creating a great threat to the water ecosystem. Advance tools and techniques are required to restore the water quality and metal-organic framework (MOFs) with a tunable porous structure, striking physical and chemical properties are an excellent candidate for it. Fe-based MOFs, which developed rapidly in recent years, are foreseen as most promising to overcome the disadvantages of traditional water depolluting practices. Fe-MOFs with low toxicity and preferable stability possess excellent performance potential for almost all water remedying techniques in contrast to other MOF structures, especially visible light photocatalysis, Fenton, and Fenton-like heterogeneous catalysis. Fe-MOFs become essential tool for water treatment due to their high catalytic activity, abundant active site and pollutant-specific adsorption. However, the structural degradation under external chemical, photolytic, mechanical, and thermal stimuli is impeding Fe-MOFs from further improvement in activity and their commercialization. Understanding the shortcomings of structural integrity is crucial for large-scale synthesis and commercial implementation of Fe-MOFs-based water treatment techniques. Herein we summarize the synthesis, structure and recent advancements in water remediation methods using Fe-MOFs in particular more attention is paid for adsorption, heterogeneous catalysis and photocatalysis with clear insight into the mechanisms involved. For ease of analysis, the pollutants have been classified into two major classes; inorganic pollutants and organic pollutants. In this review, we present for the first time a detailed insight into the challenges in employing Fe-MOFs for water remediation due to structural instability.

Magnetic porous carbons derived from iron-based metal-organic framework loaded with glucose for effective extraction of synthetic organic dyes in drinks

The conversion of metal-organic frameworks (MOFs) to porous carbon has attracted extensive attention for developing multifunctional adsorbent materials. Herein, we demonstrated a facile method to prepare magnetic porous carbon via calcinating MIL-101(Fe) precursor loaded with glucose at 700 °C in an N₂ atmosphere. The obtained magnetic porous carbon (MPCG) contained plenty of oxygen-containing functional groups and exhibited an enlarged specific surface area (177.7 m²/g) compared with its precursor (41.2 m²/g). In addition, MPCG can be easily separated from the matrix by a magnet. Benefitting from these advantages, the magnetic porous carbon exhibited high affinity toward four synthetic organic dyes (amaranth, ponceau 4R, sunset yellow, and lemon yellow) in an aqueous solution. Moreover, the adsorbent can be applied to quantitatively detect synthetic organic dyes in drinks coupled with chromatography. A new magnetic solid-phase extraction method for dye analysis yielded reasonable linearity (r □ 0.99), low limits of detection (0.047-0.076 μg/L), and good precision within the analyte concentration range of 0.25-50 μg/L.

Adsorption removal of ibuprofen and naproxen from aqueous solution with Cu-doped Mil-101(Fe)

Due to the excellent anti-inflammatory effect, ibuprofen and naproxen have been widely used in the people's daily life, which inevitably leads to their pollution in natural water environment. The removal of these chemicals from water has drawn great interests. Here, a new Cu-doped Mil-101(Fe) was synthesized through a one-step solvothermal method and successfully applied for the adsorption removal of ibuprofen and naproxen from water. A series of characterization techniques (FESEM, TEM, N₂ adsorption-desorption analysis, XRD and FT-IR) were applied to explore the physicochemical properties of the prepared Cu-doped Mil-101(Fe). The adsorption performances of the Cu-doped Mil-101(Fe) for ibuprofen and naproxen, including the adsorption kinetics and isotherms, and effects of diverse influencing factors (pH, ionic strength, and natural organic matter) were examined through batch experiments. The adsorption kinetics and isotherms of ibuprofen and naproxen on the Cu-doped Mil-101(Fe) fitted well with the pseudo-second-order model and Langmuir model, respectively. The maximum adsorption capacities of Cu-doped Mil-101(Fe) were 497.3 and 396.5 mg/g for ibuprofen and naproxen, respectively. The pH of solution in a range of 3-9 exerted no significant effects on the adsorption process. The adsorption was almost unaffected by the ionic strength and humic acid. The π-π interaction and hydrogen bond interaction between the adsorbent and adsorbates were found to be accountable for adsorption. The Cu-doped Mil-101(Fe) was readily regenerated by ethanol and could be repeatedly used.

Adsorption performance and kinetic study of hierarchical porous Fe-based MOFs for toluene removal

In light of the promising merits of large surface area, uniform pore size, and tunable functional groups, metal-organic frameworks (MOFs) have great potential to be utilized for adsorbing volatile organic compounds (VOCs). In this study, three Fe-based MOFs, MIL-100(Fe), MIL-101(Fe), and MIL-53(Fe), were synthesized systematically and used to adsorb a typical VOC, toluene. Static adsorption, dynamic breakthrough curves, and adsorption kinetics were conducted to assess the adsorption performance. Additionally, the surface functional groups, pore structure, and morphology were systematically characterized by means of XRD, SEM, XPS, FTIR and N₂ adsorption-desorption analyses to reveal the cause of the difference in adsorption of these Fe-based MOFs. The results revealed that the maximum equilibrium adsorption capacity of 663 mg/g was achieved by MIL-100(Fe) with the highest specific surface area and pore volume. The dynamic adsorption of toluene on MIL-100(Fe) was in accordance with the pseudo-first order kinetic model and the Langmuir isothermal model. The formed π-π stacking interaction between organic ligands and the benzene ring in the MIL-100(Fe) cluster is the primary adsorption mechanism based on XPS analysis. Moreover, MIL-100(Fe) was easily regenerated via microwave irradiation with a negligible adsorption capacity decrease after three cycles. This work highlights the feasibility of hierarchical porous Fe-based MOFs as toluene adsorbents and promotes the application of MOFs in the field of pollution control.

Fe-N4 Doped Carbon Nanotube Cathode Catalyst for PEM Fuel Cells

The earth-abundant iron and nitrogen doped carbon (Fe-N-C) catalyst has great potential to substitute noble metal catalysts for oxygen reduction reaction (ORR) in H₂-O₂ proton exchange membrane fuel cells (PEMFCs). Herein, we report the preparation of Fe-N₄ moiety doped carbon nanotubes (CNTs) by ball milling and two-step pyrolysis with dual metal-organic frameworks (MOFs) as the precursor. This catalyst shows high ORR catalytic performance and stability. Different from traditional inorganic iron sources, the MOF structure can effectively prevent the iron metal from aggregating during pyrolysis. In PEMFC, the catalyst shows high current density (0.39 A/cm² at 0.7 V) and power density (850 mW/cm²). Such a method brings inspiration for the reasonable design of FeNC catalysts with high catalytic activity for H₂-O₂ PEMFCs.

Cleanup of arsenic, cadmium, and lead in the soil from a smelting site using N,N-bis(carboxymethyl)-L-glutamic acid combined with ascorbic acid: A lab-scale experiment

Chemical washing has been carried out to remediate soil contaminated with heavy metals. In this study, the appropriate washing conditions for N,N-bis(carboxymethyl)-L-glutamic acid (GLDA) combined with ascorbic acid were determined to remove As, Cd, and Pb in the soil from the smelting site. The mechanism of heavy metal removal by the washing agent was also clarified. The results showed that heavy metals in the soil from the smelting site can be effectively removed. The removal percentages of As, Cd, and Pb in the soil from the smelting site were found to be 34.49%, 63.26%, and 62.93%, respectively, under optimal conditions (GLDA and ascorbic acid concentration ratio of 5:20, pH of 3, washing for 60 min, and the liquid-to-solid ratio of 10). GLDA combined with ascorbic acid efficiently removes As, Cd, and Pb from the soil through synergistic proton obstruction, chelation, and reduction. GLDA can chelate with iron and aluminum oxides while directly chelate with Cd and Pb. Ascorbic acid can reduce both Fe(III) to Fe(II) and As(III) to As⁰. The dissolution of As was promoted by indirectly preempting the binding sites of iron and aluminum in the soil while those of Cd and Pb were improved by directly interrupting the binding sites. This study suggested that GLDA combined with ascorbic acid is an effective cleanup technology to remove As, Cd, and Pb simultaneously from contaminated smelting site soils.

Mechanism of As(III) removal properties of biochar-supported molybdenum-disulfide/iron-oxide system

Sulfate (SO₄^•-) and hydroxyl-based (HO^•) radical are considered potential agents for As(III) removal from aquatic environments. We have reported the synergistic role of SO₄^•- and HO^• radicals for As(III) removal via facile synthesis of biochar-supported SO₄^•- species. MoS₂-modified biochar (MoS₂/BC), iron oxide-biochar (FeO_x@BC), and MoS₂-modified iron oxide-biochar (MoS₂/FeO_x@BC) were prepared and systematically characterized to understand the underlying mechanism for arsenic removal. The MoS₂/FeOx@BC displayed much higher As(III) adsorption (27 mg/g) compared to MoS₂/BC (7 mg/g) and FeOx@BC (12 mg/g). Effects of kinetics, As(III) concentration, temperature, and pH were also investigated. The adsorption of As(III) by MoS₂/FeOx@BC followed the Freundlich adsorption isotherm and pseudo-second-order, indicating multilayer adsorption and chemisorption, respectively. The FTIR and XPS analysis confirmed the presence of Fe-O bonds and SO₄ groups in the MoS₂/FeO_x@BC. Electron paramagnetic resonance (EPR) and radical quenching experiments have shown the generation of SO₄^•- radicals as predominant species in the presence of MoS₂ and FeO_x in MoS₂/FeOx@BC via radical transfer from HO^• to SO₄^2-. The HO^• and SO₄^•- radicals synergistically contributed to enhanced As(III) removal. It is envisaged that As(III) initially adsorbed through electrostatic interactions and partially undergoes oxidation, which is finally adsorbed to MoS₂/FeOx@BC after being oxidized to As(V). The MoS₂/FeO_x@BC system could be considered a novel material for effective removal of As(III) from aqueous environments owing to its cost-effective synthesis and easy scalability for actual applications.

Preparation of GO/MIL-101(Fe,Cu) composite and its adsorption mechanisms for phosphate in aqueous solution

In this study, MIL-101(Fe), MIL-101(Fe,Cu), and graphene oxide (GO)/MIL-101(Fe,Cu) were synthesized to compose a novel sorbent. The adsorption properties of these three MOF-based composites were compared toward the removal of phosphate. Furthermore, the influencing factors including adsorption time, pH, temperature, and initial concentration on the adsorption capacity of phosphate on these materials as well as the reusability of the material were discussed. The structure of fabricated materials and the removal mechanism of phosphate on the composite material were analyzed by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), nitrogen adsorption-desorption analysis, and zeta potential. The results show that the maximum adsorption capacity of phosphate by the composite GO/MIL-101(Fe,Cu)-2% was 204.60 mg·g^-1, which is higher than that of MIL-101(Fe,Cu) and MIL-101(Fe). likewise the specific surface area of GO/MIL-101(Fe,Cu)-2% is 778.11 m²/g is higher than that of MIL-101(Fe,Cuand MIL-101(Fe),which are 747.75 and 510.66 m²/g, respectively. The adsorption mechanism of phosphate is electrostatic attraction, forming coordination bonds and hydrogen bonds. The fabricated material is a promising adsorbent for the removal of phosphate with good reusability.

TiO2@MOF Photocatalyst for the Synergetic Oxidation of Microcystin-LR and Reduction of Cr(VI) in Aqueous Media

The coexistence of pollutants presents a great challenge to the implementation of photocatalysts. In this work, a novel MIL-101(Fe)/TiO2 composite prepared by in situ growth of MIL-101(Fe) on TiO2 was developed for the synergetic oxidation of MC-LR and Cr(VI) reduction. The heterojunction material shows elevated photocatalytic behavior under ultraviolet compared with the unary pollutant system. Furthermore, quenching experiments and electron spin resonance confirm that the enhanced photodegradation behavior is related to the synergistic effect between the photocatalytic reduction and oxidation process, in which MC-LR consumes the holes and Cr(VI) captures electrons, followed by efficient charge separation through the conventional double-transfer mechanism between MIL-101(Fe) and TiO2. This investigation provides a deeper understanding of the construction of MOFs/semiconductor heterojunctions for the pollutants removal in multi-component contaminants system.

Metal organic framework derived one-dimensional porous Fe/N-doped carbon nanofibers with enhanced catalytic performance

The aggregation of metal nanoparticles and collapse of precursor metal organic frameworks (MOFs) structure during the carbonization process largely hamper the catalytic performance of MOFs-derived carbon catalysts. Here, we report hollow and porous one-dimensional Fe/N-doped carbon nanofibers (Fe/NCNFs) for activating peroxymonosulfate (PMS), which was obtained by immobilizing Fe-MIL-101 on polyacrylonitrile (PAN) nanofibers via electrospinning technique followed by pyrolysis. The presence of one-dimensional PAN channel suppresses the agglomeration tendency of metal particles during the carbonisation process of Fe-MIL-101, resulting in a uniform dispersion of nanoparticles and an increase of catalytic active sites. The resultant Fe/NCNFs-9 possesses unique hierarchical architecture, large active surface area, well-dispersed Fe species, and abundant Fe-N active sites. These superiorities contributed to the better catalytic performance of Fe/NCNFs-9 compared with PAN derived carbon (PAN-C-9) and Fe-MIL-101 derived carbon (Fe-C-9). Through a series of inhibitor experiments and electrochemical tests, the radical pathway is dominant on BPA removal with the participation of the non-radical pathway in the multi-sites Fe/NCNFs-9/PMS/BPA system. Surprisingly, this strategy could successfully disperse Fe species and effectively reduce the Fe leaching. This work supplies a novel method to design efficient MOFs-derived carbon catalysts toward micropollutants removal.

Porous biochar-supported MnFe2O4 magnetic nanocomposite as an excellent adsorbent for simultaneous and effective removal of organic/inorganic arsenic from water

To solve the problem of organic and inorganic arsenic species contamination in drinking water and/or wastewater, porous biochar-supported MnFe₂O₄ magnetic nanocomposite (BC-MF) was successfully fabricated and used as an excellent adsorbent for simultaneous removal of p-ASA and As(V) from water environment. This obtained BC-MF displayed remarkable adsorption performance for both p-ASA and As(V) removal at acidic and neutral pH (3-7), and di-anionic and mono-anionic species of p-ASA and As(V) facilitated the adsorption process. Specifically, BC-MF exceeded some reported adsorbents, and the adsorption capacities of p-ASA and As(V) were approximately 105 and 90 mg/g at a 10 μg/L equilibrium concentration. Satisfactory adsorption behavior including adsorption isotherms, competitive ions, humic acid (HA), and regeneration/reusability property in single and binary systems demonstrated the BC-MF can improve the potential application for arsenic-containing wastewater remediation. Proposed adsorption mechanism indicated that electrostatic interaction and surface complexation were involved the p-ASA and As(V) immobilization, whereas hydrogen bonding and π-π interactions may also contribute to the p-ASA removal. Additionally, the prominent sequestration p-ASA and As(V) performance in different water matrix and fixed-bed column studies indicated that BC-MF was a promising nanocomposite for simultaneously removal of organic and inorganic arsenic species in practical wastewater treatment.

Experimental investigations into the irregular synthesis of iron(iii) terephthalate metal-organic frameworks MOF-235 and MIL-101

MOF-235(Fe) and MIL-101(Fe) are two well-studied metal-organic frameworks (MOFs) with dissimilar crystal structures and topologies. Previously reported syntheses of the former show that it has greatly varying surface areas, indicating a lack of phase purity of the products, i.e. the possible presence of both MOFs in the same sample. To find the reason for this, we have tested and modified the commonly used synthesis protocol of MOF-235(Fe), where a 3 : 5 molar ratio of iron(iii) ions and a terephthalic acid linker is heated in a 1 : 1 DMF : ethanol solvent at 80 °C for 24 h. Using XRD and BET surface area (SA_BET) measurements, we found that it is difficult to obtain a pure phase of MOF-235, as MIL-101 also appears to form during the solvothermal treatment. Comparison of the XRD peak height ratios of the synthesis products revealed a direct correlation between the MOF-235/MIL-101 content and surface area; more MOF-235 yields a lower surface area and vice versa. In general, using a larger (3 : 1) DMF : ethanol ratio than that reported in the literature and a stoichiometric (4 : 3) Fe(iii) : TPA ratio yields a nearly pure MOF-235 product (SA_BET = 295 m² g^-1, 67% yield). An optimized synthesis procedure was developed to obtain high-surface area MIL-101(Fe) (SA_BET > 2400 m² g^-1) in a large yield and at a previously unreported temperature (80 °C vs. previously used 110-150 °C). In situ X-ray scattering was utilized to investigate the crystallization of MOF-235 and MIL-101. At 80 °C, only MOF-235 formed and at 85 and 90 °C, only MIL-101 formed.

Fe2O3 enhanced high-temperature arsenic resistance of CeO2-La2O3/TiO2 catalyst for selective catalytic reduction of NO x with NH3

High-temperature arsenic resistance catalysts of CeLa_0.5Fe_x/Ti (x = 0, 0.1, 0.2, 0.3, 0.4, 0.5) series were prepared and measured under a simulation condition of arsenic poisoning. The as-prepared catalysts were characterized by XRD, SEM, TEM, and XPS. The specific surface area and pore size of the catalysts were measured. At x = 0.2, the catalyst shows the best arsenic resistance and catalytic performance. The active temperature range of the CeLa_0.5Fe_0.2/Ti catalyst is 345–520 °C when the gas hourly space velocity is up to 225 000 mL g⁻¹ h⁻¹. Compared with commercial vanadium-based catalysts, CeLa_0.5Fe_0.2/Ti shows much better catalytic performance. The introduction of Fe will improve the dispersion of CeO₂ and increase the concentration of Ce³⁺ and unsaturated active oxygen on the surface. The NH₃-TPD and H₂-TPR results show that the CeLa_0.5Fe_0.2/Ti catalyst has more acidic sites and more excellent redox performance than CeLa_0.5Fe₀/Ti. The CeLa_0.5Fe_0.2/Ti catalyst might have application prospects in the field of selective catalytic reduction of NO_x with NH₃.

The NO conversion of the CeLa_0.5Fe_0.2/Ti is obviously better than that of the commercial vanadium-based catalyst with regard to arsenic resistance and it has good N₂ selectivity, and good SO₂ resistance.