Effect of mechanical stress on biofilms challenged by different chemicals

In vitro comparison of antimicrobial effectiveness of QMix and other final irrigants in human root canals

Final root canal irrigation stands as an effective strategy for eliminating the dentin infection. This study aimed to investigate and compare the antibacterial efficacy of QMix and other four final irrigation regimens in reducing Enterococcus faecalis within human root canals. Single-canal human teeth contaminated with E. faecalis for 4 weeks were prepared chemomechanically with sodium hypochlorite (NaOCl). Then, the teeth were randomly assigned into six groups according to the final irrigation protocols: (1) EDTA/NaOCl, 17% EDTA followed by 5.25% NaOCl; (2) EDTA/chlorhexidine (CHX), 17% EDTA followed by 2% CHX; (3) EDTA/cetrimide (CTR), 17% EDTA followed by 2% CTR; (4) MTAD; (5) QMix; and (6) control, 0.9% saline. Bacterial samples collected before instrumentation and after final irrigation were cultured and the colony-forming units (CFUs) were counted. The CFUs in the QMix, EDTA/CHX, and EDTA/CTR groups were significantly lower than those in the EDTA/NaOCl group. No significant differences were observed between the QMix, EDTA/CHX, and EDTA/CTR groups. MTAD showed weaker ability than QMix and EDTA/CHX to eliminate E. faecalis, but it caused a greater reduction in CFU than EDTA/NaOCl. Hence, the antimicrobial activity of QMix was comparable to that of EDTA/CHX and EDTA/CTR and more effective than that of EDTA/NaOCl against intracanal E. faecalis.

Effect of diesel leakage in circulating cooling water system on preponderant bacteria diversity and bactericidal effect of biocides

Petroleum products leakage results in adverse effect on the normal operation of a circulating cooling water system. However, relatively little research has been done to explore the effect of petroleum products leakage on circulating cooling water quality and biofilm preponderant bacteria diversity. Also, normal biocides application modes cannot fulfil the need for biofilm control. In this study, diesel oil was used as the experimental subject representing leaking petroleum products; the effect of diesel addition on biofilm preponderant bacteria diversity and the bactericidal effect of chlorine dioxide and tetradecyl dimethyl benzyl ammonium chloride (1427) was investigated. Bacterial community structures were examined by PCR-denaturing gradient gel electrophoresis and PCR cloning of 16S rDNA genes. Except for 100 mg/L diesel, increasing diesel concentration enhanced the biofilm detachment ratio compared with the control test. The microstructure of biofilm samples with 0, 300 and 900 mg/L diesel addition was observed. The species of preponderant bacteria in the biofilm sample with 300 mg/L diesel addition were more and the bacterial distribution was more uniform than those in the biofilm sample with 900 mg/L diesel addition. With ClO2 and 1427 addition, chemical oxygen demand increased, lipid phosphorus and bacterial count first decreased and then remained stable, and the bactericidal ratio first increased and then remained stable. Diesel addition variation has more obvious effect on ClO2 than 1427.

Selected metal ions protect Bacillus subtilis biofilms from erosion

Many problems caused by bacterial biofilms can be traced back to their high resilience towards chemical perturbations and their extraordinary sturdiness towards mechanical forces. However, the molecular mechanisms that link the mechanical properties of a biofilm with the ability of bacteria to survive in different chemical environments remain enigmatic. Here, we study the erosion stability of Bacillus subtilis (B. subtilis) biofilms in the presence of different chemical environments. We find that these biofilms can utilize the absorption of certain metal ions such as Cu(2+), Zn(2+), Fe(2+), Fe(3+) and Al(3+) into the biofilm matrix to avoid erosion by shear forces. Interestingly, many of these metal ions are toxic for planktonic B. subtilis bacteria. However, their toxic activity is suppressed when the ions are absorbed into the biofilm matrix. Our experiments clearly demonstrate that the biofilm matrix has to fulfill a dual function, i.e. regulating both the mechanical properties of the biofilm and providing a selective barrier towards toxic chemicals.

Characterisation of the physical composition and microbial community structure of biofilms within a model full-scale drinking water distribution system

Within drinking water distribution systems (DWDS), microorganisms form multi-species biofilms on internal pipe surfaces. A matrix of extracellular polymeric substances (EPS) is produced by the attached community and provides structure and stability for the biofilm. If the EPS adhesive strength deteriorates or is overcome by external shear forces, biofilm is mobilised into the water potentially leading to degradation of water quality. However, little is known about the EPS within DWDS biofilms or how this is influenced by community composition or environmental parameters, because of the complications in obtaining biofilm samples and the difficulties in analysing EPS. Additionally, although biofilms may contain various microbial groups, research commonly focuses solely upon bacteria. This research applies an EPS analysis method based upon fluorescent confocal laser scanning microscopy (CLSM) in combination with digital image analysis (DIA), to concurrently characterize cells and EPS (carbohydrates and proteins) within drinking water biofilms from a full-scale DWDS experimental pipe loop facility with representative hydraulic conditions. Application of the EPS analysis method, alongside DNA fingerprinting of bacterial, archaeal and fungal communities, was demonstrated for biofilms sampled from different positions around the pipeline, after 28 days growth within the DWDS experimental facility. The volume of EPS was 4.9 times greater than that of the cells within biofilms, with carbohydrates present as the dominant component. Additionally, the greatest proportion of EPS was located above that of the cells. Fungi and archaea were established as important components of the biofilm community, although bacteria were more diverse. Moreover, biofilms from different positions were similar with respect to community structure and the quantity, composition and three-dimensional distribution of cells and EPS, indicating that active colonisation of the pipe wall is an important driver in material accumulation within the DWDS.

A comparative study of fatty acid profile and formation of biofilm inGeobacillus gargensisexposed to variable abiotic stress

Understanding bacterial fatty acid (FA) profile has a great taxonomic significance as well as clinical importance for diagnosis issues. Both the composition and nature of membrane FAs change under different nutritional, biotic and (or) abiotic stresses, and environmental stress. Bacteria produce both odd-carbon as well as branched-chain fatty acids (BCFAs). This study was designed to examine the effect of abiotic pressure, including salinity, temperature, pH, and oxinic stress on the growth, development, and FA profile in thermophilic Geobacillus gargensis. Under these stresses, 3 parametric ratios, 2-methyl fatty acids/3-methyl fatty acids (iso-/anteiso-FAs), BCFAs/straight-chain saturated fatty acids (SCSFA), and SCSFAs/straight-chain unsaturated fatty acids (SCUFA), in addition to total lipids affected by variable stresses were measured. Our results indicate that the ratio of total iso-/anteiso-FAs increased at the acidic pH range of 4.1–5.2 and decreased with increasing pH. The reverse was true for salt stress when iso-/anteiso-FAs ratio increased with salt concentration. The BCFAs/SCSFAs and SCSFAs/SCUFAs ratios increased at neutral and alkaline pH and high salt concentration, reduced incubation time, and comparatively high temperature (55–65 °C) of the growth medium. The bacterial total lipid percentage deceased with increasing salt concentration, incubation period, but it increased with temperature. The formation of extracellular polymeric substances was observed under all stress conditions and with the addition of sodium dodecyl sulfate (2 and 5 mmol/L) to the growth medium. The membrane phospholipid composition of the bacterium was analyzed by thin-layer chromatography.

Outbreaks due to Mycobacterium abscessus subsp. bolletii in southern Brazil: persistence of a single clone from 2007 to 2011

Outbreaks associated with rapidly growing mycobacteria (RGM) have been increasingly reported worldwide, including in Brazil. Among the RGM, the Mycobacterium abscessus complex is the most pathogenic and related to multidrug resistance. The aim of this study was to evaluate the antimicrobial susceptibility and molecular profile of RGM isolates involved in new postsurgical infection outbreaks in Brazil since 2007. Of the 109 cases reported in the state of Rio Grande do Sul between 2007 and 2011, 43 (39 %) had confirmed mycobacterial growth in culture. Clinical isolates were obtained from biopsy specimens or abscess aspirates. PRA-hsp65 restriction pattern identified the isolates as M. abscessus type 2, and partial rpoB sequencing confirmed the identification as M. abscessus subsp. bolletii. All isolates were susceptible to amikacin and resistant to ciprofloxacin, doxycycline, sulfamethoxazole, moxifloxacin and tobramycin. Most isolates (72 %) were fully susceptible to cefoxitin but six isolates (14 %) were fully resistant to clarithromycin. The latter differed from the susceptibility profiles of the previously described BRA100 clone from other Brazilian regions. Nevertheless, pulsed-field gel electrophoresis analysis revealed that these isolates belonged to a single BRA100 clone. In conclusion, our study reports the persistence of an emergent single and highly resistant clone of M. abscessus subsp. bolletii for several years even after national implementation of infection control measures.

Antimicrobial activity of root canal irrigants associated with cetrimide against biofilm and planktonic Enterococcus faecalis

AIM

To evaluate the antibacterial activity of sodium hypochlorite (NaOCl) and chlorhexidine (CHX) alone or associated with cetrimide (CTR), and QMiX against biofilm and planktonic Enterococcus faecalis (E. faecalis) [American type culture collection (ATCC) 29212].

MATERIALS AND METHODS

The solutions 2.5% NaOCl, 2.5% NaOCl + 0.2% CTR, 2% CHX, 2% CHX + 0.2% CTR, 0.2% CTR, and QMiX were evaluated. E. faecalis biofilms were induced for 14 days on bovine dentin blocks. The irrigants were evaluated after contact with E. faecalis suspension and biofilm for 1 and 3 minutes. After that, serial decimal dilutions were made and plated on tryptic soy agar (TSA) medium. Plates were incubated for 24 hours at 37°C and the colony-forming unit (CFU) 1 ml was determined. Data were subjected to ANOVA and Tukey's tests at 5% significance.

RESULTS

All microorganisms were eliminated by direct contact of the irrigants with planktonic cells. Only NaOCl and NaOCl + CTR were able to completely eliminate the microorganisms by direct contact with E. faecalis biofilm. CHX presented effectiveness similar to CHX + CTR CTR, and QMiX after 1 minute of contact and similar to NaOCl and NaOCl + CTR after 3 minutes (p > 0.05), but was unable to completely eliminate the microorganisms. CTR and QMiX did not differ from each other.

CONCLUSION

CTR addition to CHX and NaOCl solutions did not improve the antimicrobial activity against biofilm. All evaluated irrigants and associations presented activity against planktonic E. faecalis. Only NaOCl and NaOCl + CTR eliminated biofilm after 1 and 3 minutes of direct contact.

Antimicrobial activity of alexidine, chlorhexidine and cetrimide against Streptococcus mutans biofilm

Background

The use of antimicrobial solutions has been recommended to disinfect demineralized dentin prior to placing the filling material. The aim of this study was to evaluate the ability of several antimicrobials in controlling Streptococcus mutans (SM) biofilm formed in dentin.

Methods

Antimicrobial activity of 0.2% and 2% chlorhexidine (CHX), 0.2% cetrimide (CTR) and 0.2%, 0.5%, 1% and 2% alexidine (ALX) was assayed on 1-week SM biofilm formed on standardized coronal dentin blocks. Results of SM biofilm antimicrobial activity by different protocols were expressed as the kill percentage of biofilm and the term “eradication” was used to denote the kill of 100% of the bacterial population. To compare the efficacies of the different protocols the Student t test was used, previously subjecting data to the Anscombe transformation.

Results

All ALX concentrations tested and 0.2% CTR achieved a kill percentage higher than 99%, followed by 2% CHX with percentages above 96% (no statistically significant difference among them). Whereas 2% ALX and 0.2% CTR respectively showed eradication in 10 and 9 of the twelve specimens, 0.2% CHX did not produce eradication in any case.

Conclusions

The present study shows that, when used for one minute, 2% and 1% alexidine, and 0.2% cetrimide, achieve eradication of Streptococcus mutans biofilm in most specimens when applied to a dentin-volumetric model.

Escherichia coli adhesion, biofilm development and antibiotic susceptibility on biomedical materials

The aim of this work was to test materials typically used in the construction of medical devices regarding their influence in the initial adhesion, biofilm development and antibiotic susceptibility of Escherichia coli biofilms. Adhesion and biofilm development was monitored in 12-well microtiter plates containing coupons of different biomedical materials--silicone (SIL), stainless steel (SS) and polyvinyl chloride (PVC)--and glass (GLA) as control. The susceptibility of biofilms to ciprofloxacin and ampicillin was assessed, and the antibiotic effect in cell morphology was observed by scanning electron microscopy. The surface hydrophobicity of the bacterial strain and materials was also evaluated from contact angle measurements. Surface hydrophobicity was related with initial E. coli adhesion and subsequent biofilm development. Hydrophobic materials, such as SIL, SS, and PVC, showed higher bacterial colonization than the hydrophilic GLA. Silicone was the surface with the greatest number of adhered cells and the biofilms formed on this material were also less susceptible to both antibiotics. It was found that different antibiotics induced different levels of elongation on E. coli sessile cells. Results revealed that, by affecting the initial adhesion, the surface properties of a given material can modulate biofilm buildup and interfere with the outcome of antimicrobial therapy. These findings raise the possibility of fine-tuning surface properties as a strategy to reach higher therapeutic efficacy.

Unsaturated fatty acid, cis-2-decenoic acid, in combination with disinfectants or antibiotics removes pre-established biofilms formed by food-related bacteria

Biofilm formation by food-related bacteria and food-related pathogenesis are significant problems in the food industry. Even though much disinfection and mechanical procedure exist for removal of biofilms, they may fail to eliminate pre-established biofilms. cis-2 decenoic acid (CDA), an unsaturated fatty acid messenger produced by Pseudomonas aeruginosa, is reportedly capable of inducing the dispersion of established biofilms by multiple types of microorganisms. However, whether CDA has potential to boost the actions of certain antimicrobials is unknown. Here, the activity of CDA as an inducer of pre-established biofilms dispersal, formed by four main food pathogens; Staphylococcus aureus, Bacillus cereus, Salmonella enterica and E. coli, was measured using both semi-batch and continuous cultures bioassays. To assess the ability of CDA combined biocides treatments to remove pre-established biofilms formed on stainless steel discs, CFU counts were performed for both treated and untreated cultures. Eradication of the biofilms by CDA combined antibiotics was evaluated using crystal violet staining. The effect of CDA combined treatments (antibiotics and disinfectants) on biofilm surface area and bacteria viability was evaluated using fluorescence microscopy, digital image analysis and LIVE/DEAD staining. MICs were also determined to assess the probable inhibitory effects of CDA combined treatments on the growth of tested microorganisms' planktonic cells. Treatment of pre-established biofilms with only 310 nM CDA resulted in at least two-fold increase in the number of planktonic cells in all cultures. While antibiotics or disinfectants alone exerted a trivial effect on CFU counts and percentage of surface area covered by the biofilms, combinational treatments with both 310 nM CDA and antibiotics or disinfectants led to approximate 80% reduction in biofilm biomass. These data suggests that combined treatments with CDA would pave the way toward developing new strategies to control biofilms with widespread applications in industry as well as medicine.

Drinking water biofilm cohesiveness changes under chlorination or hydrodynamic stress

Attempts at removal of drinking water biofilms rely on various preventive and curative strategies such as nutrient reduction in drinking water, disinfection or water flushing, which have demonstrated limited efficiency. The main reason for these failures is the cohesiveness of the biofilm driven by the physico-chemical properties of its exopolymeric matrix (EPS). Effective cleaning procedures should break up the matrix and/or change the elastic properties of bacterial biofilms. The aim of this study was to evaluate the change in the cohesive strength of two-month-old drinking water biofilms under increasing hydrodynamic shear stress τw (from ∼0.2 to ∼10 Pa) and shock chlorination (applied concentration at T0: 10 mg Cl2/L; 60 min contact time). Biofilm erosion (cell loss per unit surface area) and cohesiveness (changes in the detachment shear stress and cluster volumes measured by atomic force microscopy (AFM)) were studied. When rapidly increasing the hydrodynamic constraint, biofilm removal was found to be dependent on a dual process of erosion and coalescence of the biofilm clusters. Indeed, 56% of the biofilm cells were removed with, concomitantly, a decrease in the number of the 50-300 μm(3) clusters and an increase in the number of the smaller (i.e., <50 μm(3)) and larger (i.e., >600 μm(3)) ones. Moreover, AFM evidenced the strengthening of the biofilm structure along with the doubling of the number of contact points, NC, per cluster volume unit following the hydrodynamic disturbance. This suggests that the compactness of the biofilm exopolymers increases with hydrodynamic stress. Shock chlorination removed cells (-75%) from the biofilm while reducing the volume of biofilm clusters. Oxidation stress resulted in a decrease in the cohesive strength profile of the remaining drinking water biofilms linked to a reduction in the number of contact points within the biofilm network structure in particular for the largest biofilm cluster volumes (>200 μm(3)). Changes in the cohesive strength of drinking water biofilms subsequent to cleaning/disinfection operations call into question the effectiveness of cleaning-in-place procedures. The combined alternating use of oxidation and shear stress sequences needs to be investigated as it could be an important adjunct to improving biofilm removal/reduction procedures.

Biophysics of biofilm infection

This article examines a likely basis of the tenacity of biofilm infections that has received relatively little attention: the resistance of biofilms to mechanical clearance. One way that a biofilm infection persists is by withstanding the flow of fluid or other mechanical forces that work to wash or sweep microorganisms out of the body. The fundamental criterion for mechanical persistence is that the biofilm failure strength exceeds the external applied stress. Mechanical failure of the biofilm and release of planktonic microbial cells is also important in vivo because it can result in dissemination of infection. The fundamental criterion for detachment and dissemination is that the applied stress exceeds the biofilm failure strength. The apparent contradiction for a biofilm to both persist and disseminate is resolved by recognizing that biofilm material properties are inherently heterogeneous. There are also mechanical aspects to the ways that infectious biofilms evade leukocyte phagocytosis. The possibility of alternative therapies for treating biofilm infections that work by reducing biofilm cohesion could (1) allow prevailing hydrodynamic shear to remove biofilm, (2) increase the efficacy of designed interventions for removing biofilms, (3) enable phagocytic engulfment of softened biofilm aggregates, and (4) improve phagocyte mobility and access to biofilm.

Antibiofilm activity of irrigating solutions associated with cetrimide. Confocal laser scanning microscopy

AIM

To evaluate the antibiofilm activity of sodium hypochlorite (NaOCl) and chlorhexidine (CHX) solutions associated with cetrimide (CTR), and QMiX using confocal laser scanning microscopy.

METHODOLOGY

Enterococcus faecalis (ATCC- 29212) biofilms were induced on bovine dentine blocks for 14 days. The dentine blocks containing biofilm were immersed for 1 min in the following solutions: 2.5% NaOCl; 2.5% NaOCl + 0.2% CTR; 2% CHX; 2% CHX + 0.2% CTR; 0.2% CTR; QMiX. After contact with the solutions, the dentine blocks were stained with Live/Dead(®) BacLight for analysis of the remaining biofilm using confocal laser scanning microscope. Images were evaluated using the BioImage_L software to determine the total biovolume (μm(3) ), the green biovolume (live cells) (μm(3) ) and the percentage of substrate coverage (%). The data were subjected to nonparametric statistical test using Kruskal-Wallis and Dunn's tests at 5% significance level.

RESULTS

After exposure to irrigants, the total biovolume observed for CHX, CHX+CTR, CTR, QMiX was similar to distilled water (P > 0.05). NaOCl and NaOCl+CTR had the lowest total and green biovolume. The CTR and QMiX had intermediate green biovolume, with greater antibacterial activity than CHX and CHX+CTR (P < 0.05). The NaOCl and NaOCl+CTR solutions were associated with microorganism removal and substrate cleaning ability.

CONCLUSIONS

NaOCl and NaOCl+CTR solutions were effective on microorganism viability and were able to eliminate biofilm. The addition of cetrimide did not influence antibacterial activity.

Residual activity of cetrimide and chlorhexidine on Enterococcus faecalis-infected root canals

Effective final irrigation regimen is an important step in order to achieve better disinfection and ensure residual antimicrobial effects after root canal preparation. The aim of this study was to compare the residual antimicrobial activity of 0.2% cetrimide, and 0.2% and 2% chlorhexidine in root canals infected with Enterococcus faecalis. Biofilms of E. faecalis were grown on uniradicular roots for 4 weeks. After root canal preparation, root canals were irrigated with 17% ethylenediaminetetraacetic acid (EDTA) to remove the smear layer. The roots were randomly divided into three experimental groups (n=26) according to the final irrigating solution: Group I, 5 mL 0.2% cetrimide; Group II, 5 mL 0.2% chlorhexidine; and Group III, 5 mL 2% chlorhexidine. Samples were collected for 50 days to denote the presence of bacterial growth. The proportion of ungrown specimens over 50 days was evaluated using the nonparametric Kaplan–Meier survival analysis. Differences among groups were tested using the log-rank test and the level of statistical significance was set at P<0.05. The highest survival value was found with 2% chlorhexidine, showing statistically significant differences from the other two groups. At 50 days, E. faecalis growth was detected in 69.23% specimens in Groups I and II, and in 34.61% specimens of Group III. There were no significant differences between 0.2% cetrimide and 0.2% chlorhexidine. Final irrigation with 2% chlorhexidine showed greater residual activity than 0.2% chlorhexidine and 0.2% cetrimide in root canals infected with E. faecalis.

Photodynamic biofilm inactivation by SAPYR--an exclusive singlet oxygen photosensitizer

Prevention and control of biofilm-growing microorganisms are serious problems in public health due to increasing resistances of some pathogens against antimicrobial drugs and the potential of these microorganisms to cause severe infections in patients. Therefore, alternative approaches that are capable of killing pathogens are needed to supplement standard treatment modalities. One alternative is the photodynamic inactivation of bacteria (PIB). The lethal effect of PIB is based on the principle that visible light activates a photosensitizer, leading to the formation of reactive oxygen species, e.g., singlet oxygen, which induces phototoxicity immediately during illumination. SAPYR is a new generation of photosensitizers. Based on a 7-perinaphthenone structure, it shows a singlet oxygen quantum yield ΦΔ of 99% and is water soluble and photostable. Moreover, it contains a positive charge for good adherence to cell walls of pathogens. In this study, the PIB properties of SAPYR were investigated against monospecies and polyspecies biofilms formed in vitro by oral key pathogens. SAPYR showed a dual mechanism of action against biofilms: (I) it disrupts the structure of the biofilm even without illumination; (II) when irradiated, it inactivates bacteria in a polymicrobial biofilm after one single treatment with an efficacy of ≥ 99.99%. These results encourage further investigation on the potential of PIB using SAPYR for the treatment of localized infectious diseases.

The Influence of Interfering Substances on the Antimicrobial Activity of Selected Quaternary Ammonium Compounds

Standard cleaning processes may not remove all the soiling typically found in food industry, such as carbohydrates, fats, or proteins. Contaminants have a high impact in disinfection as their presence may reduce the activity of disinfectants. The influence of alginic acid, bovine serum albumin, yeast extract, and humic acids was assessed on the antimicrobial activities of benzalkonium chloride and cetyltrimethyl ammonium bromide against Bacillus cereus vegetative cells and Pseudomonas fluorescens. The bacteria (single and consortium) were exposed to surfactants (single and combined) in the absence and presence of potential disinfection interfering substances. The antimicrobial effects of the surfactants were assessed based on the bacterial respiratory activity measured by oxygen uptake rate due to glucose oxidation. The tested surfactants were efficient against both bacteria (single and consortium) with minimum bactericidal concentrations ranging from 3 to 35 mg·L(-1). The strongest effect was caused by humic acids that severely quenched antimicrobial action, increasing the minimum bactericidal concentration of the surfactants on P. fluorescens and the consortium. The inclusion of the other interfering substances resulted in mild interferences in the antibacterial activity. This study clearly demonstrates that humic acids should be considered as an antimicrobial interfering substance in the development of disinfection strategies.

Bacteria-surface interactions

The interaction of bacteria with surfaces has important implications in a range of areas, including bioenergy, biofouling, biofilm formation, and the infection of plants and animals. Many of the interactions of bacteria with surfaces produce changes in the expression of genes that influence cell morphology and behavior, including genes essential for motility and surface attachment. Despite the attention that these phenotypes have garnered, the bacterial systems used for sensing and responding to surfaces are still not well understood. An understanding of these mechanisms will guide the development of new classes of materials that inhibit and promote cell growth, and complement studies of the physiology of bacteria in contact with surfaces. Recent studies from a range of fields in science and engineering are poised to guide future investigations in this area. This review summarizes recent studies on bacteria-surface interactions, discusses mechanisms of surface sensing and consequences of cell attachment, provides an overview of surfaces that have been used in bacterial studies, and highlights unanswered questions in this field.

Control filamentous bulking caused by chlorine-resistant Type 021N bacteria through adding a biocide CTAB

Filamentous bulking sludge due to excessive growth of filamentous bacteria is a serious operational problem in activated sludge plants. The addition of chemicals is one of widespread ways to control filamentous bulking. In this study, filamentous bulking in a continuous activated sludge system was found to be mainly caused by Eikelboom Type 021N filamentous bacteria likely due to low substrate concentration gradients. These Type 021N bacteria were found to be resistant to chlorination, maintaining cell integrity at a dosage of up to 80 mg Cl/gSS. An alternative biocidal agent, cetyltrimethyl ammonium bromide (CTAB), exhibited a much stronger biocidal effect on these filaments, which significantly improved sludge settleability. Type 021N with filamentous index of 5 was selectively killed, but floc-formers recovery their activity after CTAB termination. The study implied that CTAB might have more penetration capacity to cell wall of chlorine-resistant Type 021N bacteria. We therefore suggest the penetration property of filament cell wall should be considered or tested before the selection of biocide type in practice.

Effect of CaCO₃ particles and suspended bacteria on biofilm components and activity in the model recirculating cooling water system

Biofilms are a serious problem in industrial recirculating cooling water systems. Biofilm formation and properties are affected by many factors, such as inorganic particles and suspended bacteria. In this research a laboratory model recirculating cooling water system was applied to investigate the effects of CaCO(3) concentration and suspended bacterial count on extracellular polymeric substances (EPS) content and dehydrogenase activity (DHA) in the attached biofilms. In addition, nutrient level was also the key factor when investigating the effect of suspended bacterial count. The results showed that EPS content and DHA first increased and then decreased with the increase of CaCO(3) concentration from 0 to 200 mg/l. At the low nutrient level, with the increase of suspended bacterial count from 4.04 to 5.78 log(10) c.f.u./ml, biofilm EPS content decreased firstly and then increased. However, biofilm DHA always gradually increased. At the medium nutrient level, biofilm EPS content increased firstly and then decreased and DHA always gradually decreased when suspended bacterial count ranged from 4.04 to 5.78 log(10) c.f.u./ml. At the high nutrient level, biofilm EPS content and DHA both showed the increasing trend with the increase of suspended bacterial count. This work provides the basis and reference for management strategies in actual recirculating cooling water systems.

Pseudomonas aeruginosa attachment on QCM-D sensors: the role of cell and surface hydrophobicities

While biofilms are ubiquitous in nature, the mechanism by which they form is still poorly understood. This study investigated the process by which bacteria deposit and, shortly after, attach irreversibly to surfaces by reorienting to create a stronger interaction, which leads to biofilm formation. A model for attachment of Pseudomonas aeruginosa was developed using a quartz crystal microbalance with dissipation monitoring (QCM-D) technology, along with a fluorescent microscope and camera to monitor kinetics of adherence of the cells over time. In this model, the interaction differs depending on the force that dominates between the viscous, inertial, and elastic loads. P. aeruginosa, grown to the midexponential growth phase (hydrophilic) and stationary phase (hydrophobic) and two different surfaces, silica (SiO(2)) and polyvinylidene fluoride (PVDF), which are hydrophilic and hydrophobic, respectively, were used to test the model. The bacteria deposited on both of the sensor surfaces, though on the silica surface the cells reached a steady state where there was no net increase in deposition of bacteria, while the quantity of cells depositing on the PVDF surface continued to increase until the end of the experiments. The change in frequency and dissipation per cell were both positive for each overtone (n), except when the cells and surface are both hydrophilic. In the model three factors, specifically, viscous, inertial, and elastic loads, contribute to the change in frequency and dissipation at each overtone when a cell deposits on a sensor. On the basis of the model, hydrophobic cells were shown to form an elastic connection to either surface, with an increase of elasticity at higher overtones. At lower overtones, hydrophilic cells depositing on the hydrophobic surface were shown to also be elastic, but as the overtone increases the connection between the cells and sensor becomes more viscoelastic. In the case of hydrophilic cells interacting with the hydrophilic surface, the connection is viscous at each overtone measured. It could be inferred that the transformation of the viscoelasticity of the cell-surface connection is due to changes in the orientation of the cells to the surface, which allow the bacteria to attach irreversibly and begin biofilm formation.

Mini-review: convection around biofilms

Water that flows around a biofilm influences the transport of solutes into and out of the biofilm and applies forces to the biofilm that can cause it to deform and detach. Engineering approaches to quantifying and understanding these phenomena are reviewed in the context of biofilm systems. The slow-moving fluid adjacent to the biofilm acts as an insulator for diffusive exchange. External mass transfer resistance is important because it can exacerbate oxygen or nutrient limitation in biofilms, worsen product inhibition, affect quorum sensing, and contribute to the development of tall, fingerlike biofilm clusters. Measurements of fluid motion around biofilms by particle velocimetry and magnetic resonance imaging indicate that water flows around, but not through biofilm cell clusters. Moving fluid applies forces to biofilms resulting in diverse outcomes including viscoelastic deformation, rolling, development of streamers, oscillatory movement, and material failure or detachment. The primary force applied to the biofilm is a shear force in the main direction of fluid flow, but complex hydrodynamics including eddies, vortex streets, turbulent wakes, and turbulent bursts result in additional force components.

Hydrodynamic deformation and removal of Staphylococcus epidermidis biofilms treated with urea, chlorhexidine, iron chloride, or DispersinB

The force-deflection and removal characteristics of bacterial biofilm were measured by two different techniques before and after chemical, or enzymatic, treatment. The first technique involved time lapse imaging of a biofilm grown in a capillary flow cell and subjected to a brief shear stress challenge imparted through increased fluid flow. Biofilm removal was determined by calculating the reduction in biofilm area from quantitative analysis of transmission images. The second technique was based on micro-indentation using an atomic force microscope. In both cases, biofilms formed by Staphylococcus epidermidis were exposed to buffer (untreated control), urea, chlorhexidine, iron chloride, or DispersinB. In control experiments, the biofilm exhibited force-deflection responses that were similar before and after the same treatment. The biofilm structure was stable during the post-treatment shear challenge (1% loss). Biofilms treated with chlorhexidine became less deformable after treatment and no increase in biomass removal was seen during the post-treatment shear challenge (2% loss). In contrast, biofilms treated with urea or DispersinB became more deformable and exhibited significant biofilm loss during the post-treatment flow challenge (71% and 40%, respectively). During the treatment soak phase, biofilms exposed to urea swelled. Biofilms exposed to iron chloride showed little difference from the control other than slight contraction during the treatment soak. These observations suggest the following interpretations: (1) chemical or enzymatic treatments, including those that are not frankly antimicrobial, can alter the cohesion of bacterial biofilm; (2) biocidal treatments (e.g., chlorhexidine) do not necessarily weaken the biofilm; and (3) biofilm removal following treatment with agents that make the biofilm more deformable (e.g., urea, DispersinB) depend on interaction between the moving fluid and the biofilm structure. Measurements such as those reported here open the door to development of new technologies for controlling detrimental biofilms by targeting biofilm cohesion rather than killing microorganisms.

Bacterial attachment to RO membranes surface-modified by concentration-polarization-enhanced graft polymerization

Concentration polarization-enhanced radical graft polymerization, a facile surface modification technique, was examined as an approach to reduce bacterial deposition onto RO membranes and thus contribute to mitigation of biofouling. For this purpose an RO membrane ESPA-1 was surface-grafted with a zwitterionic and negatively and positively charged monomers. The low monomer concentrations and low degrees of grafting employed in modifications moderately reduced flux (by 20-40%) and did not affect salt rejection, yet produced substantial changes in surface chemistry, charge and hydrophilicity. The propensity to bacterial attachment of original and modified membranes was assessed using bacterial deposition tests carried out in a parallel plate flow setup using a fluorescent strain of Pseudomonas fluorescens. Compared to unmodified ESPA-1 the deposition (mass transfer) coefficient was significantly increased for modification with the positively charged monomer. On the other hand, a substantial reduction in bacterial deposition rates was observed for membranes modified with zwitterionic monomer and, still more, with very hydrophilic negatively charged monomers. This trend is well explained by the effects of surface charge (as measured by ζ-potential) and hydrophilicity (contact angle). It also well correlated with force distance measurements by AFM using surrogate spherical probes with a negative surface charge mimicking the bacterial surface. The positively charged surface showed a strong hysteresis with a large adhesion force, which was weaker for unmodified ESPA-1 and still weaker for zwitterionic surface, while negatively charged surface showed a long-range repulsion and negligible hysteresis. These results demonstrate the potential of using the proposed surface- modification approach for varying surface characteristics, charge and hydrophilicity, and thus minimizing bacterial deposition and potentially reducing propensity biofouling.

Biofouling characteristics and identification of preponderant bacteria at different nutrient levels in batch tests of a recirculating cooling water system

Understanding the influence of nutrient levels on biofouling control is an important requirement for management strategies in a recirculating cooling water system. Nutrient limitation may be one way to control biofouling development without increasing biocide dosing. Therefore, this study was carried out to investigate the effects of nutrient levels on biofouling characteristics and to identify the preponderant bacteria in the batch tests with a simulated cooling water system. The biofouling characteristics were assessed by varying the biofoulant mass and the bacteria respiratory activity, which was estimated by measuring oxygen uptake rates. According to the results obtained in nutrient factor experiments, the biofouling could be better controlled at carbon, nitrogen and phosphorus concentrations of 30 mg N/L, 8 mg N/L and 1.0 mg P/L, respectively. Increasing carbon concentrations shortened the biofouling initial growth period and resulted in higher biofoulant mass. The preponderant bacteria strains involved in biofouling under two culture conditions were identified by applying both physiological and biochemical tests and further molecular biology techniques with phylogenetic affiliation analysis. Enterobacter (family Enterobacteriaceae), Staphylococcus (family Micrococcaceae), Bacillus (family Bacillaceae), Proteus (family Enterobacteriaceae), Neisseria (family Neisseriaceae) and Pseudomonas (family Pseudomonadaceae) were dominant in the conditions of lower carbon concentration (30 mg/L). Enterobacter are autotrophs, but the other five bacteria are all heterotrophs. In the conditions of higher carbon concentration (70 mg/L), Klebsiella (family Enterobacteriaceae), Enterobacter and Microbacterium (family Microbacteriaceae) were dominant; Enterobacter and Microbacterium are heterotrophs.

The effects of glutaraldehyde on the control of single and dual biofilms of Bacillus cereus and Pseudomonas fluorescens

Glutaraldehyde (GLUT) was evaluated for control of single and dual species biofilms of Bacillus cereus and Pseudomonas fluorescens on stainless steel surfaces using a chemostat system. The biofilms were characterized in terms of mass, cell density, total and matrix proteins and polysaccharides. The control action of GLUT was assessed in terms of inactivation and removal of biofilm. Post-biocide action was characterized 3, 7, 12, 24, 48 and 72 h after treatment. Tests with planktonic cells were also performed for comparison. The results demonstrated that in dual species biofilms the metabolic activity, cell density and the content of matrix proteins were higher than those of either single species. Planktonic B. cereus was more susceptible to GLUT than P. fluorescens. The biocide susceptibility of dual species planktonic cultures was an average of each single species. Planktonic cells were more susceptible to GLUT than their biofilm counterparts. Biofilm inactivation was similar for both of the single biofilms while dual biofilms were more resistant than single species biofilms. GLUT at 200 mg l(-1) caused low biofilm removal (<10%). Analysis of the post-biocide treatment data revealed the ability of biofilms to recover their activity over time. However, 12 h after biocide application, sloughing events were detected for both single and dual species biofilms, but were more marked for those formed by P. fluorescens (removal >40% of the total biofilm). The overall results suggest that GLUT exerts significant antimicrobial activity against planktonic bacteria and a partial and reversible activity against B. cereus and P. fluorescens single and dual species biofilms. The biocide had low antifouling effects when analysed immediately after treatment. However, GLUT had significant long-term effects on biofilm removal, inducing significant sloughing events (recovery in terms of mass 72 h after treatment for single biofilms and 42 h later for dual biofilms). In general, dual species biofilms demonstrated higher resistance and resilience to GLUT exposure than either of the single species biofilms. P. fluorescens biofilms were more susceptible to the biocide than B. cereus biofilms.

Using enzymes to remove biofilms of bacterial isolates sampled in the food-industry

The aim of this study was to analyze the cleaning efficiency of polysaccharidases and proteolytic enzymes against biofilms of bacterial species found in food industry processing lines and to study enzyme effects on the composition of extracellular polymeric substances (EPS) and biofilm removal in a Clean-in-Place (CIP) procedure. The screening of 7 proteases and polysaccharidases for removal of biofilms of 16 bacterial species was first evaluated using a microtiter plate assay. The alkaline pH buffer removed more biofilm biomass as well as affecting a larger range of bacterial species. The two serine proteases and alpha-amylase were the most efficient enzymes. Proteolytic enzymes promoted biofilm removal of a larger range of bacterial species than polysaccharidases. Using three isolates derived from two bacterial species widely found in food processing lines (Pseudomonas fluorescens and the Bacillus cereus group), biofilms were developed on stainless steel slides and enzymatic solutions were used to remove the biofilms using CIP procedure. Serine proteases were more efficient in removing cells of Bacillus biofilms than polysaccharidases. However, polysaccharidases were more efficient in removing P. fluorescens biofilms than serine proteases. Solubilization of enzymes with a buffer containing surfactants, and dispersing and chelating agents enhanced the efficiency of polysaccharidases and proteases respectively in removing biofilms of Bacillus and P. fluorescens. A combination of enzymes targeting several components of EPS, surfactants, dispersing and chelating agents would be an efficient alternative to chemical cleaning agents.

Biofouling control using microparticles carrying a biocide

This study presents a new technological approach to minimize the use of antimicrobial (AMB) agents and their deleterious effects, based on the principle of drug-delivery systems whereby the AMB chemicals are transported on microparticles. The efficacy of microparticles carrying the quaternary ammonium compound (QAC), benzyldimethyldodecyl ammonium chloride (BDMDAC), was assessed against Pseudomonas fluorescens in both the planktonic and the biofilm state. The microparticles were prepared using a layer-by-layer (LBL) self-assembly technique. Oppositely charged molecules of polyethyleneimine (PEI), sodium polystyrene sulfonate (PSS), and BDMDAC were assembled on polystyrene (PS) cores. BDMDAC-coated particles were observed by CryoSEM and their composition analyzed by X-ray microanalysis. Zeta potential measurements indicated that changes in surface charge were compatible with a BDMDAC/particle interaction. This biocidal carrier structure had significant stability, verified by the release of only 15% of the BDMDAC when immersed in water for 18 months. Biocidal carrier activity was evaluated by determining the survival ratio of P. fluorescens planktonic and biofilm cells after different exposure periods to BDMDAC-coated particles. Tests with biofilm cells were also performed with the free QAC. An efficient AMB effect (minimum bactericidal concentration) against suspended cells was found for a concentration of 9.2 mg l(-1) of BDMDAC on coated particles after incubation for 30 min and 6.5 mg l(-1) of BDMDAC on coated particles after 60 min. Exposure of biofilms to PS-PEI/PSS/BDMDAC (0.87 mg l(-1)) resulted in a decrease in viability of 60.5% and 66.5% of the total biofilm population for 30 and 60 min exposure times, respectively. Exposure for 60 min to 6.33 mg l(-1) and 11.75 mg l(-1) of BDMDAC in PS-PEI/PSS/BDMDAC particles promoted inactivation of 80.6% and 87.2% of the total population, respectively. The AMB effects obtained with the application of free BDMDAC were statistically similar to those promoted by the application of BDMDAC coated particles. The overall results indicate that this novel AMB strategy has potential for the control of microbial growth of planktonic cells and biofouling. Moreover, the technique allows the reuse of AMB molecules and consequently reduces the environmental risks associated with excessive use of AMB agents, thereby providing real benefits to public health.

Epidemic of postsurgical infections caused by Mycobacterium massiliense

An epidemic of infections after video-assisted surgery (1,051 possible cases) caused by rapidly growing mycobacteria (RGM) and involving 63 hospitals in the state of Rio de Janeiro, Brazil, occurred between August 2006 and July 2007. One hundred ninety-seven cases were confirmed by positive acid-fast staining and/or culture techniques. Thirty-eight hospitals had cases confirmed by mycobacterial culture, with a total of 148 available isolates recovered from 146 patients. Most (n = 144; 97.2%) isolates presented a PRA-hsp65 restriction pattern suggestive of Mycobacterium bolletii or Mycobacterium massiliense. Seventy-four of these isolates were further identified by hsp65 or rpoB partial sequencing, confirming the species identification as M. massiliense. Epidemic isolates showed susceptibility to amikacin (MIC at which 90% of the tested isolates are inhibited [MIC(90)], 8 microg/ml) and clarithromycin (MIC(90), 0.25 microg/ml) but resistance to ciprofloxacin (MIC(90), >or=32 microg/ml), cefoxitin (MIC(90), 128 microg/ml), and doxycycline (MIC(90), >or=64 microg/ml). Representative epidemic M. massiliense isolates that were randomly selected, including at least one isolate from each hospital where confirmed cases were detected, belonged to a single clone, as indicated by the analysis of pulsed-field gel electrophoresis (PFGE) patterns. They also had the same PFGE pattern as that previously observed in two outbreaks that occurred in other Brazilian cities; we designated this clone BRA100. All five BRA100 M. massiliense isolates tested presented consistent tolerance to 2% glutaraldehyde. This is the largest epidemic of postsurgical infections caused by RGM reported in the literature to date in Brazil.

Species association increases biofilm resistance to chemical and mechanical treatments

The study of biofilm ecology and interactions might help to improve our understanding of their resistance mechanisms to control strategies. Concerns that the diversity of the biofilm communities can affect disinfection efficacy have led us to examine the effect of two antimicrobial agents on two important spoilage bacteria. Studies were conducted on single and dual species biofilms of Bacillus cereus and Pseudomonas fluorescens. Biofilms were formed on a stainless steel rotating device, in a bioreactor, at a constant Reynolds number of agitation (Re(A)). Biofilm phenotypic characterization showed significant differences, mainly in the metabolic activity and both extracellular proteins and polysaccharides content. Cetyl trimethyl ammonium bromide (CTAB) and glutaraldehyde (GLUT) solutions in conjunction with increasing Re(A) were used to treat biofilms in order to assess their ability to kill and remove biofilms. B. cereus and P. fluorescens biofilms were stratified in a layered structure with each layer having differential tolerance to chemical and mechanical stresses. Dual species biofilms and P. fluorescens single biofilms had both the highest resistance to removal when pre-treated with CTAB and GLUT, respectively. B. cereus biofilms were the most affected by hydrodynamic disturbance and the most susceptible to antimicrobials. Dual biofilms were more resistant to antimicrobials than each single species biofilm, with a significant proportion of the population remaining in a viable state after exposure to CTAB or GLUT. Moreover, the species association increased the proportion of viable cells of both bacteria, comparatively to the single species scenarios, enhancing each other's survival to antimicrobials and the biofilm shear stress stability.

Physiology and behavior of Pseudomonas fluorescens single and dual strain biofilms under diverse hydrodynamics stresses

Three selected Pseudomonas fluorescens strains (the type strain and two strains originally isolated from a dairy processing plant - D3-348 and D3-350) were used to form turbulent and laminar flow-generated biofilms under laboratorial conditions using flow cell reactors with stainless steel substrata. The D3-348 and D3-350 strains were also used to form dual biofilms. Biofilm phenotypic characteristics, such as respiratory activity, total and culturable cells, biomass, total and matrix proteins and polysaccharides were compared. Biofilm mechanical stability, as a major feature involved in biofilm persistence, was also assessed using a rotating device system. The results indicate that hydrodynamic conditions have a remarkable impact on biofilm phenotype. Turbulent biofilms were more active, had more mass per adhesion surface area, a higher number of total and culturable cells, a higher amount of total proteins per gram of biofilm, similar matrix proteins and identical (D3-348 and D3-350 single and dual biofilms) or smaller (type strain) total and matrix polysaccharides content than their laminar counterparts. Biofilms formed by the type strain revealed a considerable higher amount of total and culturable cells and a higher amount of total proteins (turbulent biofilms) and total and matrix polysaccharides per gram of biofilm than single and dual biofilms formed by the other strains. Mechanical stability assays disclosed that biofilms formed by both type and D3-348 strains had the highest resistance to removal when exposed to mechanical stress. Dual strain biofilms population analysis revealed an apparent co-existence, evidencing neutral interactions. The overall results provided useful information regarding a broad spectrum of P. fluorescens biofilm phenotypic parameters, which can contribute to control and model biofilm processes in food industry.

Antagonism between Bacillus cereus and Pseudomonas fluorescens in planktonic systems and in biofilms

In the environment, many microorganisms coexist in communities competing for resources, and they are often associated as biofilms. The investigation of bacterial ecology and interactions may help to improve understanding of the ability of biofilms to persist. In this study, the behaviour of Bacillus cereus and Pseudomonas fluorescens in the planktonic and sessile states was compared. Planktonic tests were performed with single and dual species cultures in growth medium with and without supplemental FeCl3. B. cereus and P. fluorescens single cultures had equivalent growth behaviours. Also, when in co-culture under Fe-supplemented conditions, the bacteria coexisted and showed similar growth profiles. Under Fe limitation, 8 h after co-culture and over time, the number of viable B. cereus cells decreased compared with P. fluorescens. Spores were detected during the course of the experiment, but were not correlated with the decrease in the number of viable cells. This growth inhibitory effect was correlated with the release of metabolite molecules by P. fluorescens through Fe-dependent mechanisms. Biofilm studies were carried out with single and dual species using a continuous flow bioreactor rotating system with stainless steel (SS) substrata. Steady-state biofilms were exposed to a series of increasing shear stress forces. Analysis of the removal of dual species biofilms revealed that the outer layer was colonised mainly by B. cereus. This bacterium was able to grow in the outermost layers of the biofilm due to the inhibitory effect of P. fluorescens being decreased by the exposure of the cells to fresh culture medium. B. cereus also constituted the surface primary coloniser due to its favourable adhesion to SS. P. fluorescens was the main coloniser of the middle layers of the biofilm. Single and dual species biofilm removal data also revealed that B. cereus biofilms had the highest physical stability, followed by P. fluorescens biofilms. This study highlights the inadequacy of planktonic systems to mimic the behaviour of bacteria in biofilms and shows how the culturing system affects the action of antagonist metabolite molecules because dilution and consequent loss of activity occurred in continuously operating systems. Furthermore, the data demonstrate the biocontrol potential of P. fluorescens on the planktonic growth of B. cereus and the ability of the two species to coexist in a stratified biofilm structure.

Sodium dodecyl sulfate allows the persistence and recovery of biofilms of Pseudomonas fluorescens formed under different hydrodynamic conditions

The effect of the anionic surfactant sodium dodecyl sulfate (SDS) on Pseudomonas fluorescens biofilms was investigated using flow cell reactors with stainless steel substrata, under turbulent (Re = 5200) and laminar (Re = 2000) flow. Steady-state biofilms were exposed to SDS in single doses (0.5, 1, 3 and 7 mM) and biofilm respiratory activity and mass measured at 0, 3, 7 and 12 h after the SDS application. The effect of SDS on biofilm mechanical stability was assessed using a rotating bioreactor. Whilst high concentrations (7 mM) of SDS promoted significant biofilm inactivation, it did not significantly reduce biofouling. Turbulent and laminar flow-generated biofilms had comparable susceptibility to SDS application. Following SDS exposure, biofilms rapidly recovered over the following 12 h, achieving higher respiratory activity values than before treatment. This phenomenon of post-treatment recovery was more pronounced for turbulent flow-generated biofilms, with an increase in SDS concentration. The mechanical stability of the biofilms increased with surfactant application, except for SDS concentrations near the critical micellar concentration, as measured by biofilm removal due to an increase in external shear stress forces. The data suggest that although SDS exerts antimicrobial action against P. fluorescens biofilms, even if only partial and reversible, it had only limited antifouling efficacy, increasing biofilm mechanical stability at low concentrations and allowing significant and rapid recovery of turbulent flow-generated biofilms.

The effect of hydrodynamic conditions on the phenotype of Pseudomonas fluorescens biofilms

This study investigated the phenotypic characteristics of monoculture P. fluorescens biofilms grown under turbulent and laminar flow, using flow cells reactors with stainless steel substrata. The cellular physiology and the overall biofilm activity, structure and composition were characterized, and compared, within hydrodynamically distinct conditions. The results indicate that turbulent flow-generated biofilm cells were significantly less extensive, with decreased metabolic activity and a lower protein and polysaccharides composition per cell than those from laminar flow-generated biofilms. The effect of flow regime did not cause significantly different outer membrane protein expression. From the analysis of biofilm activity, structure and composition, turbulent flow-generated biofilms were metabolically more active, had twice more mass per cm(2), and higher cellular density and protein content (mainly cellular) than laminar flow-generated biofilms. Conversely, laminar flow-generated biofilms presented higher total and matrix polysaccharide contents. Direct visualisation and scanning electron microscopy analysis showed that these different flows generate structurally different biofilms, corroborating the quantitative results. The combination of applied methods provided useful information regarding a broad spectrum of biofilm parameters, which can contribute to control and model biofilm processes.