Detection of hydrazine, methylhydrazine, and isoniazid by capillary electrophoresis with a palladium-modified microdisk array electrode

Preparation of TiO2-Pt hybrid nanofibers and their application for sensitive hydrazine detection

The TiO2-Pt hybrid nanofibers with an average dia. 72.6 nm were fabricated by electrospinning poly(vinylpyrrolidone)-ethanol solution containing platinum acetate and titanium tetraisopropoxide, followed by calcination in air at 500 °C for 3 h. High resolution TEM showed that Pt nanoparticles with an average diameter of ∼2 nm were well dispersed in the anatase TiO2 nanofibers. Compared to pristine TiO2 nanofibers (average dia. 67.7 nm), the incorporation of Pt nanoparticles into TiO2 nanofibers can greatly enhance the oxidation of hydrazine in neutral solution. The amperometric hydrazine sensor, using the as-prepared TiO2-Pt hybrid nanofibers as the electrochemical catalyst, shows a wide linear range (up to 1.03 mM), a good limit of detection (0.142 µM), and a high sensitivity of 44.42 µA mM(-1) cm(-2). In addition, the excellent anti-interference property, free of matrix effect from real water samples and good reproducibility make the developed hydrazine sensor promising for real applications.

Control and analysis of hydrazine, hydrazides and hydrazones--genotoxic impurities in active pharmaceutical ingredients (APIs) and drug products

This is the latest of a series of reviews focused on the analysis of genotoxic impurities. This review summarises the analytical approaches reported in the literature relating to hydrazine, hydrazines, hydrazides and hydrazones. It is intended to provide guidance for analysts needing to develop procedures to control such impurities, particularly where this is due to concerns relating to their potential genotoxicity. Of particular note is the wide variety of techniques employed, both chromatographic and spectroscopic, with most involving derivatisation. Such a wide variety of options allow the analyst a real choice in terms of selecting the most appropriate technique specific to their requirements. Several generic methodologies, covering the three main analytical approaches; i.e. HPLC (high performance liquid chromatography), GC (gas chromatography) and IC (ion chromatography), are also described.

Development of extraction and analytical methods of nitrite ion from food samples: microchip electrophoresis with a modified electrode

Two simple and fast methods for the extraction of the nitrite ion (NO(2)(-)) from food samples have been developed. The methods were characterized by UV-visible spectroscopic and electrochemical measurements, and their performance for NO(2)(-) extraction was compared with a standard method. The extraction methods yielded relative recoveries between 100 and 120% with good reproducibility of 3.9% (RSD, n = 4) in UV-visible experiments. Microchip electrophoresis with electrochemical detection (MCE-ED) coupled with a copper (3-mercaptopropyl)trimethoxysilane [Cu(II)-MPS] complex-modified carbon paste electrode (CPE) has been employed to detect NO(2)(-) in extracted samples. The Cu(II)-MPS complex was synthesized and characterized by voltammetry, XPS, and FT-IR analyses. Experimental parameters affecting the separation and detection performances of the MCE-ED method were assessed and optimized. The potential for the electrocatalytic reduction of NO(2)(-) for MCE-ED was found to be -190 mV (vs Ag/AgCl). When extracted food samples were analyzed by the MCE-ED method, a reproducible response for the NO(2)(-) reduction (RSD of 4.3%) at the modified-CPE reflected the negligible electrode fouling. A wide dynamic range of 1.0-160 ppm was observed for analyzing standard NO(2)(-) with a sensitivity of 0.05106 ± 0.00141, and the detection limit, based on S/N = 3, was found to be 0.35 ± 0.05 ppm. No apparent interference from NO(3)(-), other inorganic ions, and biological compounds was observed under the optimal experimental conditions. A standard addition method for real samples showed wide concentration ranges of 1.10-155 and 1.2-150 ppm for analyzing NO(2)(-) in ham and sausage samples, respectively.

Microelectrode arrays for electrochemistry: approaches to fabrication

Microelectrode arrays have unique electrochemical properties such as small capacitive-charging currents, reduced iR drop, and steady-state diffusion currents. These properties enable the use of microelectrode arrays and have captured much interest in the field of electrochemistry. Techniques for the fabrication of such arrays are reviewed. The relative features and merits of different techniques are also discussed.

Cyclic voltammograms at coplanar and shallow recessed microdisk electrode arrays: guidelines for design and experiment

Although microdisk electrode arrays (MEAs) have been extensively used for more than three decades, the existing rules do not provide an unambiguous formula for the calculation of the minimum interelectrode distance (d) necessary for steady-state current response. With the aim of formulating generally applicable guidelines for design and experiment with MEAs, cyclic voltammograms were simulated for coplanar and shallow recessed microdisk electrode arrays with various interelectrode distances and dimensionless scan rates (V). The dimensionless scan rate (V) is a function of the radius (a) of the individual electrodes in the array, the diffusion coefficient (D) of the analyte, and the potential scan rate (v). The cyclic voltammograms at microdisk electrode arrays are grouped into five categories corresponding to the contributions of linear and radial diffusion to the overall responses. These categories are illustrated in a zone diagram based on the effect of V and d on the shape of cyclic voltammograms. The zone diagram reveals the minimum d and a cluster of linked d and V values that are incident to sigmoidal wave responses. For shallow recessed microdisk electrode arrays, the zones representing hemispherical diffusion are larger than that for coplanar arrays. The minimum d necessary for hemispherical diffusion becomes smaller as recess depth increases. With the zone diagram, one can predict the type of the cyclic voltammograms that can be expected for different microelectrode array geometries and experimental conditions. The fitting between simulation and experimental data validates our conclusions.

Design of an optical sensor for indirect determination of isoniazid

The characterization of an optical sensor membrane is described for indirect determination of isoniazid. The sensing membrane was consisted of immobilized 3-(2-pyridyl)-5,6-diphenyl-1,2,4-triazine (PDT) on a triacetylcellulose membrane. The procedure is based on the reaction of Fe(III) with isoniazid in the presence of PDT. Fe(III) is reduced by isoniazid to Fe(II) which forms a complex with PDT. The complex shows an absorption maximum at 558nm. By measuring the absorbance of the complex at this wavelength, isoniazid can be determined in the range of 0.62-6.15microgmL(-1). This method was applied to the determination of isoniazid in pharmaceutical formulation and enabled the determination of isoniazid in microgram quantities.

Simultaneous electrochemical determination of dopamine, uric acid and ascorbic acid using palladium nanoparticle-loaded carbon nanofibers modified electrode

Palladium nanoparticle-loaded carbon nanofibers (Pd/CNFs) were prepared by electrospinning and subsequent thermal treatment processes. Pd/CNFs modified carbon paste electrode (Pd/CNF-CPE) displayed excellent electrochemical catalytic activities towards dopamine (DA), uric acid (UA) and ascorbic acid (AA). The oxidation overpotentials of DA, UA and AA were decreased significantly compared with those obtained at the bare CPE. Differential pulse voltammetry was used for the simultaneous determination of DA, UA and AA in their ternary mixture. The peak separation between UA and DA, DA and AA was 148 mV and 244 mV, respectively. The calibration curves for DA, UA and AA were obtained in the range of 0.5-160 microM, 2-200 microM, and 0.05-4mM, respectively. The lowest detection limits (S/N=3) were 0.2 microM, 0.7 microM and 15 microM for DA, UA and AA, respectively. With good selectively and sensitivity, the present method was applied to the determination of DA in injectable medicine and UA in urine sample.

Validation of a rapid micellar electrokinetic capillary chromatographic method for the simultaneous determination of isoniazid and pyridoxine hydrochloride in pharmaceutical formulation

An efficient and reliable micellar electrokinetic capillary chromatography (MEKC) method has been developed for the simultaneous determination of isoniazid (ISO) and pyridoxine hydrochloride (PYR) in pharmaceutical formulations. A chemometric two level full factorial design approach was used to search for the optimum conditions of separation. Three parameters were selected for this study: the buffer pH, the buffer concentration and sodium dodecyl sulphate (SDS) concentrations. Resolution, peak symmetry and analysis time were established as response. The two analytes were separated within 6 min with the optimized conditions: 50 mM borate buffer, 25 mM SDS pH 7.8, 35 degrees C, at 50 mbar 4s injection and 30 kV by using a fused silica capillary (72 cm effective length, 50 microm i.d.). The detection wavelength was set to 205 nm. Meloxicam was used as internal standard. The method was validated with respect to stability, linearity range, limit of quantitation and detection, precision, accuracy, specificity and robustness. The detection limits of the method were 1.0 microg mL(-1) for ISO and 0.40 microg mL(-1) for PYR and the method was linear at least in the range of 3.0-100 microg mL(-1) for ISO and 1.0-100 microg mL(-1) for PYR with excellent correlation coefficients (0.9995 for ISO and 0.9998 for PYR). Relative standard deviations (R.S.D.s) of the described method ranged between 0.54 and 2.27% for intra-day precision and between 0.65 and 2.69% for inter-day precision. The developed method was applied to the tablet form of ISO and PYR-containing the pharmaceutical preparations and the data were compared with obtained from the standard addition method. No statistically significant difference was found.

Fast BIA-amperometric determination of isoniazid in tablets

This paper proposes a new, fast and precise method to analyze isoniazid based on the electrochemical oxidation of the analyte at a glassy carbon electrode in 0.1M NaOH. The quantification was performed utilizing amperometry associated with batch injection analysis (BIA) technique. Fast sequential analysis (60 determinations h(-1)) in an unusually wide linear dynamic range (from 2.5 x 10(-8) to 1.0 x 10(-3)M), with high sensitivity and low limits of detection (4.1 x 10(-9)M) and quantification (1.4 x 10(-8)M), was achieved. Such characteristics allied to a good repeatability of the current responses (relative standard deviation of 0.79% for 30 measurements), were explored for the specific determination of isoniazid in isoniazid-rifampin tablet.

Electrochemical oxidation of isoniazid catalyzed by (FcM)TMA at the platinum electrode and its practical analytical application

The electrocatalytic oxidation of isoniazid (INH) by (ferrocenylmethyl)trimethylammonium [(FcM)TMA] at the platinum electrode in 0.10 M Na2SO4 aqueous solution was studied by cyclic voltammetry (CV). Although INH itself showed a very poor electrochemical response at the platinum electrode, the response could be greatly enhanced by using (FcM)TMA as a mediator, which enables a sensitive electrochemical determination of the substrate INH. The reaction rate constant for catalytic oxidation reaction was evaluated as (3.98+/-0.10)x10(3) M(-1) s(-1) by using chronoamperometry (CA). Experimental conditions such as supporting electrolyte and its concentration, solution pH, and the concentrations of the catalyst (FcM)TMA and the substrate INH were investigated to maximize the current efficiency of the electrocatalytic oxidation. The method can be used for the sensitive practical determination of INH, and also opens an avenue for using (FcM)TMA as a mediator in electroanalytical determination which is very simple, cheap, and rapid. Furthermore, no sample pretreatment or time-consuming extraction steps are required prior to the analysis.

The electroanalytical detection of hydrazine: A comparison of the use of palladium nanoparticles supported on boron-doped diamond and palladium plated BDD microdisc array

We show that both a random distribution of palladium nanoparticles supported on a BDD electrode or a palladium plated BDD microelectrode array can each provide a sensing platform for the electrocatalytic detection of hydrazine. The palladium nanoparticle modified electrode displays a sensitivity and limit of detection of 60 mA mol(-1) L and 2.6 microM respectively while the array has a sensitivity of 8 mA mol(-1) L with a detection limit of 1.8 microM. The beneficial cost implications of using palladium nano- or micro-particles in sensors compared to a palladium macroelectrode are evident. Interestingly the array of the nanoparticles shows similar sensitivity and limit of detection to the microelectrode array which probably indicates that the random distribution of the former leads to 'clumps' of nanoparticles that effectively act as microelectrodes.

Determination of hydrazine, monomethylhydrazine, 1,1-dimethylhydrazine, and 1,2-dimethylhydrazine by nonaqueous capillary electrophoresis with amperometric detection

The present study is concerned with the application of nonaqueous capillary electrophoresis (NACE) with electrochemical detection (ED) to the separation and quantitative determination of hydrazine (Hy) and its methyl derivatives. The best performance of NACE-ED was found when using 4 mM sodium acetate/10 mM acetic acid/methanol: acetonitrile = 1:2 as the running buffer, with a bare platinum working electrode set at +1.0 V in an end-column amperometric detection cell. The choice and ratio of suitable solvents for the separation and injection media played an essential role for the performance characteristics of the method. The limits of detection for Hy, methylhydrazine, symmetrical dimethylhydrazine, and unsymmetrical dimethylhydrazine were 5, 2, 12, and 1 ng/mL, respectively. This is between one and two orders of magnitude lower than that achieved by previously reported CE-ED methods in aqueous buffer systems in conjunction with various types of chemically modified electrodes. The practical utility of the new NACE-ED methodology is demonstrated in terms of the determination of traces of Hys in spiked environmental samples containing a wide range of explosives and related compounds.