Surfactant-Mediated Cloud Point Extractions: An Environmentally Benign Alternative Separation Approach

A new approach for separation and recovery of betaine from beet molasses based on cloud point extraction technique

The aim of this work was to explore the possibility of the application of cloud point extraction (CPE) method in micelle media to recovery betaine from beet molasses. Response surface method was employed to assess the effects of surfactant concentration, molasses concentration, incubation time, pH, electrolyte concentration, mixing time, and surfactant type on efficiency of betaine recovery from beet molasses. Also, a mathematical model was developed to predict the effect of each variable and their interactions on the efficiency of betaine recovery. The model showed that best surfactant was Triton X-114 and under the optimum conditions, betaine recovery from beet molasses was achieved up to 80% when three CPE steps with total of 1.5% (w/v) of surfactant were used. Subsequently, betaine was recovered nearly 100% from surfactant rich phase after adjusting pH at 2.5 and re-incubation at 40 °C. The results showed that the proposed method is suitable for extraction of betaine from beet molasses.

Clouding phenomenon in amphiphilic systems: A review of five decades

Phase separation in amphiphilic systems is an important phenomenon. The temperature at which an amphiphilic solution phase separates is known as Cloud Point (CP). This article reviews in detail the process of phase separation in various amphiphiles (surfactants, polymers and drugs) and effect of different classes of additives on the CP of these amphiphilic systems. Ions affect the CP of drugs in a different way: kosmotropes and hard bases decrease while chaotropes and soft bases increase the CP of nonionic and cationic surfactants. Anionic surfactants show CP in presence of quaternary salts only. Thus, depending upon the nature and concentration of additive, the CP of an amphiphilic system gets increased or decreased and, hence, properties of the system may be tuned as per the need and use. A system with CP at high concentration can be made to phase separate at lower concentration by simply introducing an appropriate additive in it. This makes the system cost effective. On the other hand, if not required, a low CP can be enhanced with the help of another type of a suitable additive.

Solid phase extraction based on the phase transition of poly(N-isopropylacrylamide): the extraction behaviour of lanthanide(iii) ions in highly acidic solutions

The extraction of the complex of Ln(iii) ions and CMPO onto the PNIPAAm solid phase formed by phase transition was achieved in highly acidic solutions.

A novel liquid-liquid extraction for the determination of naphthalene by GC-MS with deuterated anthracene as internal standard

Polycyclic aromatic hydrocarbons are known for their carcinogenic and mutagenic effects on human health. This therefore calls for the regulation of their concentrations in air, water, and soil. Naphthalene as the simplest in structure of the polycyclic aromatic hydrocarbons is mainly used as a starter material for other chemicals but also has impacts on human health. A method is therefore proposed for the determination of naphthalene in water samples by gas chromatography mass spectrometry after liquid-liquid extraction. The extraction method was optimized to improve the extraction output, thereby lowering the limit of detection. The limits of detection and quantification obtained for naphthalene were 4.4 and 14.6 ng mL^-1, respectively. Deuterated anthracene was used as internal standard to enhance the precision of the method, for which a relative standard deviation of 4.3% was obtained. The percent recovery of naphthalene obtained from tap water was ranged between 93.8 and 102.2.

Green analytical chemistry – the use of surfactants as a replacement of organic solvents in spectroscopy

This chapter gives an introduction to the many practical uses of surfactants in analytical chemistry in replacing organic solvents to achieve greener chemistry. Taking a holistic approach, it covers​ some background of surfactants as chemical solvents, their properties and as green chemicals, including their environmental effects. The achievements of green analytical chemistry with micellar systems are reviewed in all the major areas of analytical chemistry where these reagents have been found to be useful.

Biotoxicity and bioavailability of hydrophobic organic compounds solubilized in nonionic surfactant micelle phase and cloud point system

A recent work has shown that hydrophobic organic compounds solubilized in the micelle phase of some nonionic surfactants present substrate toxicity to microorganisms with increasing bioavailability. However, in cloud point systems, biotoxicity is prevented, because the compounds are solubilized into a coacervate phase, thereby leaving a fraction of compounds with cells in a dilute phase. This study extends the understanding of the relationship between substrate toxicity and bioavailability of hydrophobic organic compounds solubilized in nonionic surfactant micelle phase and cloud point system. Biotoxicity experiments were conducted with naphthalene and phenanthrene in the presence of mixed nonionic surfactants Brij30 and TMN-3, which formed a micelle phase or cloud point system at different concentrations. Saccharomyces cerevisiae, unable to degrade these compounds, was used for the biotoxicity experiments. Glucose in the cloud point system was consumed faster than in the nonionic surfactant micelle phase, indicating that the solubilized compounds had increased toxicity to cells in the nonionic surfactant micelle phase. The results were verified by subsequent biodegradation experiments. The compounds were degraded faster by PAH-degrading bacterium in the cloud point system than in the micelle phase. All these results showed that biotoxicity of the hydrophobic organic compounds increases with bioavailability in the surfactant micelle phase but remains at a low level in the cloud point system. These results provide a guideline for the application of cloud point systems as novel media for microbial transformation or biodegradation.

Optimization of a cloud point extraction procedure with response surface methodology for the quantification of dissolved iron in produced water from the petroleum industry using FAAS

The characterization of inorganic elements in the produced water (PW) samples is a difficult task because of the complexity of the matrix. This work deals with a study of a methodology for dissolved Fe quantification in PW from oil industry by flame atomic absorption spectrometry (FAAS) after cloud point extraction (CPE). The procedure is based on the CPE using PAN as complexing agent and Triton X-114 as surfactant. The best conditions for Fe extraction parameters were studied using a Box-Behnken design. The proposed method presented a LOQ of 0.010μgmL^-1 and LOD of 0.003μgmL^-1. The precision of the method was evaluated in terms of repeatability, obtaining a coefficient of variation of 2.54%. The accuracy of the method was assessed by recovery experiments of Fe spiked that presented recovery of 103.28%. The method was applied with satisfactory performance to determine Fe by FAAS in PW samples.

Coacervation with surfactants: From single-chain surfactants to gemini surfactants

Coacervation is a spontaneous process during which a colloidal dispersion separates into two immiscible liquid phases: a colloid-rich liquid phase in equilibrium with a diluted phase. Coacervation is usually divided into simple coacervation and complex coacervation according to the number of components. Surfactant-based coacervation normally contains traditional single-chain surfactants. With the development of surfactants, gemini surfactants with two amphiphilic moieties have been applied to form coacervation. This review summarizes the development of simple coacervation and complex coacervation in the systems of single-chain surfactants and gemini surfactants. Simple coacervation in surfactant solutions with additives or at elevated temperature and complex coacervation in surfactant/polymer mixtures by changing charge densities, molecular weight, ionic strength, pH, or temperature are reviewed. The comparison between gemini surfactants and corresponding monomeric single-chain surfactants reveals that the unique structures of gemini surfactants endow them with higher propensity to generate coacervation.

Temperature-Induced Aggregate Transitions in Mixtures of Cationic Ammonium Gemini Surfactant with Anionic Glutamic Acid Surfactant in Aqueous Solution

The aggregation behaviors of the mixtures of cationic gemini surfactant 1,4-bis(dodecyl-N,N-dimethylammonium bromide)-2,3-butanediol (C12C4(OH)2C12Br2) and anionic amino acid surfactant N-dodecanoylglutamic acid (C12Glu) in aqueous solution of pH = 10.0 have been studied. The mixture forms spherical micelles, vesicles, and wormlike micelles at 25 °C by changing mixing ratios and/or total surfactant concentration. Then these aggregates undergo a series of transitions upon increasing the temperature. Smaller spherical micelles transfer into larger vesicles, vesicles transfer into solid spherical aggregates and then into larger irregular aggregates, and entangled wormlike micelles transfer into branched wormlike micelles. Moreover, the larger irregular aggregates and branched micelles finally lead to precipitation and clouding phenomenon, respectively. All these transitions are thermally reversible, and the transition temperatures can be tuned by varying the mixing ratios and/or total concentration. These temperature-dependent aggregate transitions can be elucidated on the basis of the temperature-induced variations in the dehydration, electrostatic interaction, and hydrogen bonds of the headgroup area and in the hydrophobic interaction between the hydrocarbon chains. The results suggest that the surfactants carrying multiple binding sites will greatly improve the regulation ability and temperature sensitivity.

Cloud point extraction of disulfiram for its HPLC-MS/MS determination in synthetic urine

A new simple cloud point extraction/preconcentration method was developed for the HPLC-MS/MS determination of disulfiram in synthetic urine. Some parameters with an effect on the extraction, such as the concentration of Triton X-114, pH influence, incubation time, equilibration temperature and centrifuging parameters, were studied and optimised. The method proposed for the HPLC-MS/MS determination of disulfiram in synthetic urine with preliminary cloud point extraction was validated. The calibration curve was linear in the range of 0.025-15.4 ng mL

Cloud Point Extraction for Electroanalysis: Anodic Stripping Voltammetry of Cadmium

Cloud point extraction (CPE) is a well-established technique for the preconcentration of hydrophobic species from water without the use of organic solvents. Subsequent analysis is then typically performed via atomic absorption spectroscopy (AAS), UV-vis spectroscopy, or high performance liquid chromatography (HPLC). However, the suitability of CPE for electroanalytical methods such as stripping voltammetry has not been reported. We demonstrate the use of CPE for electroanalysis using the determination of cadmium (Cd(2+)) by anodic stripping voltammetry (ASV). Rather than using the chelating agents which are commonly used in CPE to form a hydrophobic, extractable metal complex, we used iodide and sulfuric acid to neutralize the charge on Cd(2+) to form an extractable ion pair. This offers good selectivity for Cd(2+) as no interferences were observed from other heavy metal ions. Triton X-114 was chosen as the surfactant for the extraction because its cloud point temperature is near room temperature (22-25 °C). Bare glassy carbon (GC), bismuth-coated glassy carbon (Bi-GC), and mercury-coated glassy carbon (Hg-GC) electrodes were compared for the CPE-ASV. A detection limit for Cd(2+) of 1.7 nM (0.2 ppb) was obtained with the Hg-GC electrode. ASV with CPE gave a 20x decrease (4.0 ppb) in the detection limit compared to ASV without CPE. The suitability of this procedure for the analysis of tap and river water samples was demonstrated. This simple, versatile, environmentally friendly, and cost-effective extraction method is potentially applicable to a wide variety of transition metals and organic compounds that are amenable to detection by electroanalytical methods.

Single-step, paper-based concentration and detection of a malaria biomarker

The lateral-flow immunoassay (LFA) is an inexpensive and rapid paper-based assay that can potentially detect infectious disease biomarkers in resource-poor settings. Despite its many advantages that make it suitable for point-of-care diagnosis, LFA is limited by its inferior sensitivity relative to sophisticated laboratory-based assays. Our group previously introduced the use of a micellar aqueous two-phase system (ATPS), comprised of the nonionic Triton X-114 surfactant, to concentrate biomarkers in a sample and enhance their detection with LFA. However, achieving complete phase separation and target concentration using the Triton X-114 system required many hours, and the concentrated sample needed to be manually extracted and applied to LFA. Here, we successfully integrated the concentration and detection steps into a single step that occurs entirely within a portable paper-based diagnostic strip. In a novel approach, we applied the micellar ATPS to a 3-D paper design and effectively reduced the macroscopic phase separation time from 8 h to approximately 3 min. The 3-D design was integrated with LFA to simultaneously concentrate and detect Plasmodium lactate dehydrogenase (pLDH), a malaria biomarker, in both phosphate-buffered saline and fetal bovine serum within 20 min at room temperature. Compared to a conventional LFA setup with a pLDH detection limit of 10 ng μL(-1), our single-step diagnostic successfully detected pLDH at 1.0 ng μL(-1), demonstrating a 10-fold detection limit improvement and resulting in a sensitive and user-friendly assay that can be used at the point-of-care. The integration of a micellar ATPS and LFA represents a new platform that can improve and promote the use of paper-based diagnostic assays for malaria and other diseases within resource-poor settings.

Development of a cloud point extraction and spectrophotometry-based microplate method for the determination of nitrite in human urine and blood

A novel and simple method for the sensitive determination of trace amounts of nitrite in human urine and blood has been developed by combination of cloud point extraction (CPE) and microplate assay. The method is based on the Griess reaction and the reaction product is extracted into nonionic surfactant Triton-X114 using CPE technique. In this study, decolorization treatment of urine and blood was applied to overcome the interference of matrix and enhance the sensitivity of nitrite detection. Multi-sample can be simultaneously detected thanks to a 96-well microplate technique. The effects of different operating parameters such as type of decolorizing agent, concentration of surfactant (Triton X-114), addition of (NH4)2SO4, extraction temperature and time, interfering elements were studied and optimum conditions were obtained. Under the optimum conditions, a linear calibration graph was obtained in the range of 10-400 ng mL(-1) of nitrite with limit of detection (LOD) of 2.5 ng mL(-1). The relative standard deviation (RSD) for determination of 100 ng mL(-1) of nitrite was 2.80%. The proposed method was successfully applied for the determination of nitrite in the urine and blood samples with recoveries of 92.6-101.2%.

Mixed micelle cloud point-magnetic dispersive μ-solid phase extraction of doxazosin and alfuzosin

Mixed micelle cloud point extraction (MM-CPE) combined with magnetic dispersive μ-solid phase extraction (MD-μ-SPE) has been developed as a new approach for the extraction of doxazosin (DOX) and alfuzosin (ALF) prior to fluorescence analysis. The mixed micelle anionic surfactant sodium dodecyl sulfate and non-ionic polyoxyethylene(7.5)nonylphenylether was used as the extraction solvent in MM-CPE, and diatomite bonding Fe₃O₄ magnetic nanoparticles were used as the adsorbent in MD-μ-SPE. The method was based on MM-CPE of DOX and ALF in the surfactant-rich phase. Magnetic materials were used to retrieve the surfactant-rich phase, which easily separated from the aqueous phase under magnetic field. At optimum conditions, a linear relationship between DOX and ALF was obtained in the range of 5-300 ng mL(-1), and the limits of detection were 0.21 and 0.16 ng mL(-1), respectively. The proposed method was successfully applied for the determination of the drugs in pharmaceutical preparations, urine samples, and plasma samples.

Micellar extraction possesses a new advantage for the analysis of Alzheimer's disease brain proteome

Integral membrane proteins (MPs), such as transporters, receptors, and ion channels, are of great interest because of their participation in various vital cellular functions including cell-cell interactions, ion transport, and signal transduction. However, studies of MPs are complicated because of their hydrophobic nature, heterogeneity, and low abundance. Cloud-point extraction (CPE) with the non-ionic surfactant Triton X-114 was performed to simultaneously extract and phase separate hydrophobic and hydrophilic proteins from Alzheimer's disease (AD) and unaffected control brain tissue. Quantitative proteomics analysis of temporal neocortex samples of AD patients and controls was performed using a shotgun approach based on stable isotope dimethyl labeling (DML) quantification technique followed by nanoLC-MS/MS analysis. A total of 1096 unique proteins were identified and quantified, with 40.3 % (211/524) predicted as integral MPs with at least one transmembrane domain (TMD) found in the detergent phase, and 10 % (80/798) in the detergent-depleted phase. Among these, 62 proteins were shown to be significantly altered (p-value <0.05), in AD versus control samples. In the detergent fraction, we found 10 hydrophobic transmembrane proteins containing up to 14 putative TMDs that were significantly up- or down-regulated in AD compared with control brains. Changes in four of these proteins, alpha-enolase (ENOA), lysosome-associated membrane glycoprotein 1 (LAMP1), 14-3-3 protein gamma (1433G), and sarcoplasmic/endoplasmic reticulum calcium ATPase2 (AT2A2) were validated by immunoblotting. Our results emphasize that separating hydrophobic MPs in CPE contributes to an increased understanding of the underlying molecular mechanisms in AD. Such knowledge can become useful for the development of novel disease biomarkers.

Novel lipase purification methods - a review of the latest developments

Microbial lipases are popular biocatalysts due to their ability to catalyse diverse reactions such as hydrolysis, esterification, and acidolysis. Lipases function efficiently on various substrates in aqueous and non-aqueous media. Lipases are chemo-, regio-, and enantio-specific, and are useful in various industries, including those manufacturing food, detergents, and pharmaceuticals. A large number of lipases from fungal and bacterial sources have been isolated and purified to homogeneity. This success is attributed to the development of both conventional and novel purification techniques. This review highlights the use of these techniques in lipase purification, including conventional techniques such as: (i) ammonium sulphate fractionation; (ii) ion-exchange; (iii) gel filtration and affinity chromatography; as well as novel techniques such as (iv) reverse micellar system; (v) membrane processes; (vi) immunopurification; (vi) aqueous two-phase system; and (vii) aqueous two-phase floatation. A summary of the purification schemes for various bacterial and fungal lipases are also provided.

Toward a robust analytical method for separating trace levels of nano-materials in natural waters: cloud point extraction of nano-copper(II) oxide

Cloud point extraction (CPE) factors, namely Triton X-114 (TX-114) concentration, pH, ionic strength, incubation time, and temperature, were optimized for the separation of nano-sized copper(II) oxide (nCuO) in aqueous matrices. The kinetics of phase transfer was studied using UV-visible spectroscopy. From the highest separation rate, the most favorable conditions were observed with 0.2 % w/v of TX-114, pH = 9.0, ionic strength of 10 mM NaCl, and incubation at 40 °C for 60 min, yielding an extraction efficiency of 89.2 ± 3.9 % and a preconcentration factor of 86. The aggregate size distribution confirmed the formation of very large nCuO-micelle assemblies (11.9 μm) under these conditions. The surface charge of nCuO was also diminished effectively. An extraction efficiency of 91 % was achieved with a mixture of TX-100 and TX-114 containing 30 wt.% of TX-100. Natural organic and particulate matters, represented by humic acid (30 mg/L) and micron-sized silica particles (50 mg/L), respectively, did not significantly reduce the CPE efficiency (<10 %). The recovery of copper(II) ions (20 mg/L) in the presence of humic acid was low (3-10 %). The spiked natural water samples were analyzed either directly or after CPE by inductively coupled plasma mass spectrometry following acid digestion/microwave irradiation. The results indicated the influence of matrix effects and their reduction by CPE. A delay between spiking nCuO and CPE may also influence the recovery of nCuO due to aggregation and dissolution. A detection limit of 0.04 μg Cu/L was achieved for nCuO.

Using an aqueous two-phase polymer-salt system to rapidly concentrate viruses for improving the detection limit of the lateral-flow immunoassay

The development of point-of-need (PON) diagnostics for viruses has the potential to prevent pandemics and protects against biological warfare threats. Here we discuss the approach of using aqueous two-phase systems (ATPSs) to concentrate biomolecules prior to the lateral-flow immunoassay (LFA) for improved viral detection. In this paper, we developed a rapid PON detection assay as an extension to our previous proof-of-concept studies which used a micellar ATPS. We present our investigation of a more rapid polymer-salt ATPS that can drastically improve the assay time, and show that the phase containing the concentrated biomolecule can be extracted prior to macroscopic phase separation equilibrium without affecting the measured biomolecule concentration in that phase. We could therefore significantly decrease the time of the diagnostic assay with an early extraction time of just 30 min. Using this rapid ATPS, the model virus bacteriophage M13 was concentrated between approximately 2 and 10-fold by altering the volume ratio between the two phases. As the extracted virus-rich phase contained a high salt concentration which destabilized the colloidal gold indicator used in LFA, we decorated the gold nanoprobes with polyethylene glycol (PEG) to provide steric stabilization, and used these nanoprobes to demonstrate a 10-fold improvement in the LFA detection limit. Lastly, a MATLAB script was used to quantify the LFA results with and without the pre-concentration step. This approach of combining a rapid ATPS with LFA has great potential for PON applications, especially as greater concentration-fold improvements can be achieved by further varying the volume ratio. Biotechnol. Bioeng. 2014;111: 2499-2507. © 2014 Wiley Periodicals, Inc.

Antioxidant Activity and Thermal Stability of Oleuropein and Related Phenolic Compounds of Olive Leaf Extract after Separation and Concentration by Salting-Out-Assisted Cloud Point Extraction

A fast, clean, energy-saving, non-toxic method for the stabilization of the antioxidant activity and the improvement of the thermal stability of oleuropein and related phenolic compounds separated from olive leaf extract via salting-out-assisted cloud point extraction (CPE) was developed using Tween 80. The process was based on the decrease of the solubility of polyphenols and the lowering of the cloud point temperature of Tween 80 due to the presence of elevated amounts of sulfates (salting-out) and the separation from the bulk solution with centrifugation. The optimum conditions were chosen based on polyphenols recovery (%), phase volume ratio (V_s/V_w) and concentration factor (F_c). The maximum recovery of polyphenols was in total 95.9%; V_s/V_w was 0.075 and F_c was 15 at the following conditions: pH 2.6, ambient temperature (25 °C), 4% Tween 80 (w/v), 35% Na₂SO₄ (w/v) and a settling time of 5 min. The total recovery of oleuropein, hydroxytyrosol, luteolin-7-O-glucoside, verbascoside and apigenin-7-O-glucoside, at optimum conditions, was 99.8%, 93.0%, 87.6%, 99.3% and 100.0%, respectively. Polyphenolic compounds entrapped in the surfactant-rich phase (V_s) showed higher thermal stability (activation energy (Ea) 23.8 kJ/mol) compared to non-entrapped ones (Ea 76.5 kJ/mol). The antioxidant activity of separated polyphenols remained unaffected as determined by the 1,1-diphenyl-2-picrylhydrazyl method.