Screening and production of rhamnolipids by Pseudomonas aeruginosa 47T2 NCIB 40044 from waste frying oils

Response Surface Methodology for Optimizing the Production of Biosurfactant by Candida tropicalis on Industrial Waste Substrates

Biosurfactant production optimization by Candida tropicalis UCP0996 was studied combining central composite rotational design (CCRD) and response surface methodology (RSM). The factors selected for optimization of the culture conditions were sugarcane molasses, corn steep liquor, waste frying oil concentrations and inoculum size. The response variables were surface tension and biosurfactant yield. All factors studied were important within the ranges investigated. The two empirical forecast models developed through RSM were found to be adequate for describing biosurfactant production with regard to surface tension (R² = 0.99833) and biosurfactant yield (R² = 0.98927) and a very strong, negative, linear correlation was found between the two response variables studied (r = −0.95). The maximum reduction in surface tension and the highest biosurfactant yield were 29.98 mNm⁻¹ and 4.19 gL⁻¹, respectively, which were simultaneously obtained under the optimum conditions of 2.5% waste frying oil, 2.5%, corn steep liquor, 2.5% molasses, and 2% inoculum size. To validate the efficiency of the statistically optimized variables, biosurfactant production was also carried out in 2 and 50 L bioreactors, with yields of 5.87 and 7.36 gL⁻¹, respectively. Finally, the biosurfactant was applied in motor oil dispersion, reaching up to 75% dispersion. Results demonstrated that the CCRD was suitable for identifying the optimum production conditions and that the new biosurfactant is a promising dispersant for application in the oil industry.

Production kinetics of polyhydroxyalkanoates by using Pseudomonas aeruginosa gamma ray mutant strain EBN-8 cultured on soybean oil

The purpose of present study was to optimize polyhydroxyalkanotes (PHAs) production in a gamma ray mutant strain of Pseudomonas aeruginosa grown on soybean oil in minimal salts media under shake flask conditions. The production kinetics was studied by sampling on daily basis for 6 days to investigate the best conditions for PHAs production like biomass estimation, carbon source utilization and PHAs yield. The PHA accumulation was observed up to 50.27 % (w/w) of cell dry mass. The Pseudomonas species synthesized medium chain length PHA copolyester as per identified by LCMS and confirmed by FTIR spectroscopy. The ESI-MS analysis exhibited the major polyhydroxybutyrate with a molecular mass of m/z 448.5.

Antifungal Activity of Isolated Bacillus amyloliquefaciens SYBC H47 for the Biocontrol of Peach Gummosis

The gummosis disease is caused by Botryosphaeria dothidea (Moug. ex. Fr) Ces. et de Not., and it is one of the most important diseases of stone fruits worldwide. The use of biocontrol as an alternative approach to synthetic chemical fungicides has aroused general concern about how to control plant diseases that are caused by phytopathogens. The aim of this study is to isolate Bacillus strains from raw honeys with the capacity to inhibit B. dothidea and to explore the mechanisms by which they could be used in the biocontrol of peach gummosis. Bacillus amyloliquefaciens SYBC H47 was isolated and identified on the basis of its physiological and biochemical characteristics and its 16S rRNA and gyrB gene sequences. The cell suspension and the cell-free supernatant of its culture showed significant antifungal activity against Aspergillus niger, Mucor racemosus, Fusarium oxysporum, Penicillium citrinum, and Candida albicans by agar-diffusion assays. The primary antifungal substances were bacillomycin L, fengycin, and surfactin, which were analyzed by HPLC LC/ESI-MS/MS. Bacillomycin L showed the best inhibitory effect against conidial germination of B. dothidea, followed by fengycin and surfactin. Surfactin had limited effects on mycelial growth, contrary to those of bacillomycin L and fengycin. However, a mixture of the three lipopeptides had a synergistic effect that disrupted the structure of the conidia and mycelia. In order to reduce the production cost, the use of waste frying peanut oil and soy oil as the sole carbon source increased the lipopeptide yield levels by approximately 17% (2.42 g/L) and 110% (4.35 g/L), respectively. In a field trial, the decreases in the infected gummosis rate (IGR) and the disease severity index (DSI) through cell suspension treatments were 20% and 57.5% (in 2014), respectively, and 40% and 57.5% (in 2015), respectively, in comparison with the control. In conclusion, B. amyloliquefaciens SYBC H47 could inhibit the germination of conidia and the growth of mycelia from B. dothidea; therefore, this strain behaves as a potential biocontrol agent against the gummosis disease.

Utilization of Paneer Whey Waste for Cost-Effective Production of Rhamnolipid Biosurfactant

The present study aimed at isolating rhamnolipid biosurfactant-producing bacteria that could utilize paneer whey, an abundant waste source as sole medium for the production purpose. Pseudomonas aeruginosa strain, SR17, was isolated from hydrocarbon-contaminated soil that could efficiently utilize paneer whey for rhamnolipid production and reduce surface tension of the medium from 52 to 26.5 mN/m. The yield of biosurfactant obtained was 2.7 g/l, upgraded to 4.8 g/l when supplemented with 2 % glucose and mineral salts. Biochemical, FTIR, and LC-MS analysis revealed that extracted biosurfactant is a combination of both mono and di-rhamnolipid congeners. The critical micelle concentration (CMC) was measured to be 110 mg/l. Emulsification activity of the biosurfactant against n-hexadecane, olive oil, kerosene, diesel oil, engine oil, and crude oil were found to be 83, 88, 81, 92, 86, and 100 %, respectively. The rhamnolipid was detected to be non-toxic against mouse fibroblastic cell line L292.

Biosurfactants: Multifunctional Biomolecules of the 21st Century

In the era of global industrialisation, the exploration of natural resources has served as a source of experimentation for science and advanced technologies, giving rise to the manufacturing of products with high aggregate value in the world market, such as biosurfactants. Biosurfactants are amphiphilic microbial molecules with hydrophilic and hydrophobic moieties that partition at liquid/liquid, liquid/gas or liquid/solid interfaces. Such characteristics allow these biomolecules to play a key role in emulsification, foam formation, detergency and dispersal, which are desirable qualities in different industries. Biosurfactant production is considered one of the key technologies for development in the 21st century. Besides exerting a strong positive impact on the main global problems, biosurfactant production has considerable importance to the implantation of sustainable industrial processes, such as the use of renewable resources and "green" products. Biodegradability and low toxicity have led to the intensification of scientific studies on a wide range of industrial applications for biosurfactants in the field of bioremediation as well as the petroleum, food processing, health, chemical, agricultural and cosmetic industries. In this paper, we offer an extensive review regarding knowledge accumulated over the years and advances achieved in the incorporation of biomolecules in different industries.

Rhamnolipid biosurfactants: evolutionary implications, applications and future prospects from untapped marine resource

Rhamnolipid-biosurfactants are known to be produced by the genus Pseudomonas, however recent literature reported that rhamnolipids (RLs) are distributed among diverse microbial genera. To integrate the evolutionary implications of rhamnosyl transferase among various groups of microorganisms, a comprehensive comparative motif analysis was performed amongst bacterial producers. Findings on new RL-producing microorganism is helpful from a biotechnological perspective and to replace infective P. aeruginosa strains which ultimately ensure industrially safe production of RLs. Halotolerant biosurfactants are required for efficient bioremediation of marine oil spills. An insight on the exploitation of marine microbes as the potential source of RL biosurfactants is highlighted in the present review. An economic production process, solid-state fermentation using agro-industrial and industrial waste would increase the scope of biosurfactants commercialization. Potential and prospective applications of RL-biosurfactants including hydrocarbon bioremediation, heavy metal removal, antibiofilm activity/biofilm disruption and greener synthesis of nanoparticles are highlighted in this review.

Cost effective technologies and renewable substrates for biosurfactants' production

Diverse types of microbial surface active amphiphilic molecules are produced by a range of microbial communities. The extraordinary properties of biosurfactant/bioemulsifier (BS/BE) as surface active products allows them to have key roles in various field of applications such as bioremediation, biodegradation, enhanced oil recovery, pharmaceutics, food processing among many others. This leads to a vast number of potential applications of these BS/BE in different industrial sectors. Despite the huge number of reports and patents describing BS and BE applications and advantages, commercialization of these compounds remain difficult, costly and to a large extent irregular. This is mainly due to the usage of chemically synthesized media for growing producing microorganism and in turn the production of preferred quality products. It is important to note that although a number of developments have taken place in the field of BS industries, large scale production remains economically challenging for many types of these products. This is mainly due to the huge monetary difference between the investment and achievable productivity from the commercial point of view. This review discusses low cost, renewable raw substrates, and fermentation technology in BS/BE production processes and their role in reducing the production cost.

Isolation and characterization of biosurfactant production under extreme environmental conditions by alkali-halo-thermophilic bacteria from Saudi Arabia

Twenty three morphologically distinct microbial colonies were isolated from soil and sea water samples, which were collected from Jeddah region, Saudi Arabia for screening of the most potent biosurfactant strains. The isolated bacteria were selected by using different methods as drop collapse test, oil displacement test, blue agar test, blood hemolysis test, emulsification activity and surface tension. The results showed that the ability of Virgibacillus salarius to grow and reduce surface tension under a wide range of pH, salinities and temperatures gives bacteria isolate an advantage in many applications such as pharmaceutical, cosmetics, food industries and bioremediation in marine environment. The biosurfactant production by V. salarius decreased surface tension and emulsifying activity (30 mN/m and 80%, respectively). In addition to reducing the production cost of biosurfactants by tested several plant-derived oils such as jatropha oil, castor oils, jojoba oil, canola oil and cottonseed oil. In this respect the feasibility to reusing old frying oil of sunflower for production rhamnolipids and sophorolipids, their use that lead to solve many ecological and industrial problems.

Rhamnolipids as emulsifying agents for essential oil formulations: antimicrobial effect against Candida albicans and methicillin-resistant Staphylococcus aureus

This work examines the influence of essential oil composition on emulsification with rhamnolipids and their use as therapeutic antimicrobial agents against two opportunistic pathogens, methicillin-resistant Staphylococcus aureus (MRSA) and Candida albicans. Rhamnolipids, produced by Pseudomonas aeruginosa, with waste frying oil as the carbon source, were composed of eight rhamnolipid homologues. The rhamnolipid mixture was used to produce emulsions containing essential oils (EOs) of Melaleuca alternifolia, Cinnamomum verum, Origanum compactum and Lavandula angustifolia using the titration method. Ternary phase diagrams were designed to evaluate emulsion stability, which differed depending on the essential oil. The in vitro antimicrobial activity of the EOs alone and the emulsions was evaluated. The antimicrobial activity presented by the essential oils alone increased with emulsification. The surface properties of rhamnolipids contribute to the positive dispersion of EOs and thus increase their availability and antimicrobial activity against C. albicans and S. aureus. Therefore, rhamnolipid-based emulsions represent a promising approach to the development of EO delivery systems.

Yield and kinetic constants estimation in the production of hydroxy fatty acids from oleic acid in a bioreactor by Pseudomonas aeruginosa 42A2

We modelled the production of hydroxy fatty acids from oleic acid by Pseudomonas aeruginosa 42A2 in a bioreactor with a non-dispersive aeration system. First, we designed an adapted wetted-wall gas-absorption column, offering a k La value of 39.9 h(-1), to enhance oxygen absorption in the culture media and prevent foam formation. Then, we analysed different kinetic models to simulate the yield coefficients and the kinetic constants in this bacterial transformation. Monod model fitting (μ max1 = 0.51 h(-1), K S1 = 1.60 C-mol l(-1), μ max2 = 0.12 h(-1), K S2 = 0.035 C-mol l(-1), and k 2 = 0.033 h(-1)) showed a good accuracy with the experimental data sets and was chosen for its simplicity. Lastly, mass balances were carried out to establish the stoichiometry of this biotransformation with the following yield coefficients, Υ X/OA, Υ X/(10S)-HPOME and Υ (10S)-HPOME/(7S10S)-HPOME of 0.172, 0.347 and 2.388 C-mol C-mol(-1), respectively.

Sulfur source-mediated transcriptional regulation of the rhlABC genes involved in biosurfactants production by Pseudomonas sp. strain AK6U

Despite the nutritional significance of sulfur, its influence on biosurfactants production has not been sufficiently studied. We investigated the expression of key biosurfactants production genes, rhlABC, in cultures of Pseudomonas sp. AK6U grown with inorganic or organic sulfur sources. AK6U grew with either inorganic sulfate (MgSO₄), dibenzothiophene (DBT), or DBT-sulfone as a sole sulfur source in the presence of glucose as a carbon source. The AK6U cultures produced variable amounts of biosurfactants depending on the utilized sulfur source. Biosurfactants production profile of the DBT cultures was significantly different from that of the DBT-sulfone and inorganic sulfate cultures. The last two cultures were very similar in terms of biosurfactants productivity. Biosurfactants yield in the DBT cultures (1.3 g/L) was higher than that produced by the DBT-sulfone (0.5 g/L) and the inorganic sulfate (0.44 g/L) cultures. Moreover, the surface tension reduction in the DBT cultures (33 mN/m) was much stronger than that measured in the DBT-sulfone (58 mN/m) or inorganic sulfate (54 mN/m) cultures. RT-qPCR revealed variations in the expression levels of the rhlABC genes depending on the sulfur source. The DBT cultures had higher expression levels for the three genes as compared to the DBT-sulfone and inorganic sulfate cultures. There was no significant difference in the expression profiles between the DBT-sulfone and the MgSO₄ cultures. The increased expression of rhlC in the DBT cultures is indicative for production of higher amounts of dirhamnolipids compared to the DBT-sulfone and inorganic sulfate cultures. The gene expression results were in good agreement with the biosurfactants production yields and surface tension measurements. The sulfur source mediates a fine-tuned mechanism of transcriptional regulation of biosurfactants production genes. Our findings can have an impact on industrial production of biosurfactants and other biotechnological processes like biodesulfurization.

Characterization of a biosurfactant produced by Pseudomonas cepacia CCT6659 in the presence of industrial wastes and its application in the biodegradation of hydrophobic compounds in soil

The bacterium Pseudomonas cepacia CCT6659 cultivated with 2% soybean waste frying oil and 2% corn steep liquor as substrates produced a biosurfactant with potential application in the bioremediation of soils. The biosurfactant was classified as an anionic biomolecule composed of 75% lipids and 25% carbohydrates. Characterization by proton nuclear magnetic resonance ((1)H and (13)C NMR) revealed the presence of carbonyl, olefinic and aliphatic groups, with typical spectra of lipids. Four sets of biodegradation experiments were carried out with soil contaminated by hydrophobic organic compounds amended with molasses in the presence of an indigenous consortium, as follows: Set 1-soil+bacterial cells; Set 2-soil+biosurfactant; Set 3-soil+bacterial cells+biosurfactant; and Set 4-soil without bacterial cells or biosurfactant (control). Significant oil biodegradation activity (83%) occurred in the first 10 days of the experiments when the biosurfactant and bacterial cells were used together (Set 3), while maximum degradation of the organic compounds (above 95%) was found in Sets 1-3 between 35 and 60 days. It is evident from the results that the biosurfactant alone and its producer species are both capable of promoting biodegradation to a large extent.

Produção de biossurfactante por Chromobacterium violaceum ATCC 12472 utilizando milhocina e óleo de milho pós-fritura como nutrientes

O interesse em surfactantes de origem microbiana tem aumentado consideravelmente nos últimos anos. A preocupação ambiental entre os consumidores, combinada às novas legislações de controle do meio ambiente, aumentou a procura por surfactantes naturais em substituição aos derivados petroquímicos. Os surfactantes microbianos têm sido testados em muitas aplicações ambientais e industriais, como na biorremediação, na dispersão de manchas oleosas e na recuperação de petróleo, substituindo os surfactantes químicos. Além disso, também podem ser utilizados nas indústrias de alimentos, cosméticos, detergentes e na agricultura. Neste trabalho foi produzido biossurfactante por Chromobacterium violaceum ATCC 12472, utilizando nutrientes de baixo valor agregado. A tensão superficial do biossurfactante produzido por C. violaceum ATCC 12472 teve valores entre 29 e 40 mN/m. O melhor resultado foi observado no ensaio 8 (milhocina 8,0%, lactose 1,0% e óleo de milho pós-fritura 7,5%) do planejamento fatorial, com 72 horas de fermentação, reduzindo a tensão superficial da água de 71 para 29 mN/m. Os melhores resultados do índice (E24) e da atividade de emulsificação (UEA) foram observados no ponto central, sendo utilizados para ambos os métodos o óleo de milho, que resultou no E24 de 2% e atividade com valores acima de 6 UAE. Os resultados obtidos demonstram o elevado potencial de C. violaceum na produção de um promissor biossurfactante.

Production and characterization of a trehalolipid biosurfactant produced by the novel marine bacterium Rhodococcus sp., strain PML026

AIMS

The aim of this study was to evaluate biosurfactant production by a novel marine Rhodococcus sp., strain PML026 and characterize the chemical nature and properties of the biosurfactant.

METHODS AND RESULTS

A novel marine bacterium (Rhodococcus species; strain PML026) was shown to produce biosurfactant in the presence of hydrophobic substrate (sunflower oil). Biosurfactant production (identified as a trehalolipid) was monitored in whole-batch cultures (oil layer and aqueous phase), aqueous phase (no oil layer) and filtered (0·2 μm) aqueous phase (no oil or cells; extracellular) and was shown to be closely associated with growth/biomass production. Extracellular trehalolipid levels increased postonset of stationary growth phase. Purified trehalolipid was able to reduce the surface tension of water to 29 mN m(-1) at Critical Micellar Concentration (CMC) of c. 250 mg l(-1) and produced emulsions that were stable to a wide range of conditions (pH 2-10, temperatures of 20-100°C and NaCl concentrations of 5-25% w/v). Separate chemical analyses of the intact trehalolipid and its constituents demonstrated the compound was in fact a mixture of homologues (>1180 MW) consisting of a trehalose moiety esterified to a series of straight chain and hydroxylated fatty acids.

CONCLUSIONS

The trehalolipid biosurfactant produced by the novel marine strain Rhodococcus sp. PML026 was characterized and exhibited high surfactant activity under a wide range of conditions.

SIGNIFICANCE AND IMPACT OF STUDY

Strain PML026 of Rhodococcus sp. is a potential candidate for bioremediation or biosurfactant production for various applications.

Structural Elucidation and Surfactant Properties of Rhamnolipids Synthesized by Pseudomonas aeruginosa (ATCC 10145) on Sweet Water as Carbon Source and Stabilization Effect on Foam Produced by Sodium Lauryl Sulfate

The interest in biosurfactant has increased considerably due to their large potential for industrial applications. Rhamnolipid is the simplest class of biosurfactants with well defined structure. The main obstacle in commercialization of biosurfactant especially rhamnolipids is the higher cost of the production that can be reduced by use of inexpensive carbon substrates like glycerol that is readily available from commercial fat-splitting process in the form of sweet water (up to 20% w/v) at very low cost. The composition and structure of various components in crude rhamnolipids synthesized by of Pseudomonas aeruginosa (ATCC 10145) on sweet water, were determined using TLC, HPLC and LC\MS. The crude product showed two distinct components having structure Rha2C10C10 and Rha2C10C12 at 85.45 wt.% and 14.55 wt.% respectively. The Rha2C10C10 was more efficient and effective in surface tension reduction up to 23.5 mN/m than other components. Crude rhamnolipids showed better emulsifying power than its individual components. The crude rhamnolipids showed better foam stability than sodium lauryl sulfate (SLS) at lower concentrations (0.05 to 0.002% w/v). It also enhanced and stabilized the foam produced by SLS at 0.01 to 0.025% of rhamnolipids.

Halomonas sp. BS4, A biosurfactant producing halophilic bacterium isolated from solar salt works in India and their biomedical importance

Halophilic bacteria were isolated from Thamaraikulam solar salt works in India. After routine biosurfactant screening by various methods, the biosurfactant producing bacteria, Halomonas sp BS4 was confirmed by 16 S rRNA sequencing. The growth optimization of Halomonas sp BS4 revealed their optimum growth at 8% NaCl and 6-8 pH in the growth medium. Further the partially purified biosurfactants were characterized by TLC, FTIR and GC-MS analysis. GC-MS results revealed that, the partial purified biosurfactants contain 1, 2-Ethanediamine N, N, N’, N’-tetra, 8-Methyl-6-nonenamide, (Z)-9-octadecenamide and a fatty acid derivative. Pharmacological screening of antibacterial, antifungal, antiviral and anticancer assays revealed that, the biosurfactant extracted from Halomonas sp BS4 effectively controlled the human pathogenic bacteria and fungi an aquaculturally important virus, WSSV. The biosurfactant also suppressed the proliferation of mammary epithelial carcinoma cell by 46.77% at 2.5 μg concentration. Based on these findings, the present study concluded that, there is a possibility to develop eco-friendly antimicrobial and anticancer drugs from the extremophilic origin.

Study of Glycerol Residue as a Carbon Source for Production of Rhamnolipids by Pseudomonas aeruginosa (ATCC 10145)

Rhamnolipid is the simplest class of biosurfactants with a well defined structure. The main obstacle in commercialization of biosurfactant especially rhamnolipids is the higher cost of the production. The production cost can be reduced by using economical carbon sources. Glycerol residue is available from glycerin distillation plant at low cost. It can be used as carbon source for rhamnolipid production using Pseudomonas aeruginosa (ATCC 10145). The optimum concentration of glycerol residue was 5% weight by volume (w/v) yielding maximum rhamnolipids at 2.50 g/L in the broth. From batch monitoring of polyglycerol and monoglycerol consumption, it appeared that polyglycerols were first hydrolyzed to monoglycerol in the broth itself and consumed as carbon source. The product had components similar to rhamnolipids synthesized on pure glycerol under the same conditions. This indicated the potential of glycerol residue as economic substrate for production of rhamnolipids.

Study of Glycerol and Sweet Water as a Carbon Source for Production of Rhamnolipids by Naturally Occurring Strains of Pseudomonas aeruginosa (ATCC 10145 and ATCC 9027)

The interest in biosurfactant has increased considerably due to their large potential for industrial applications. Rhamnolipid is a simplest class of biosurfactants with well defined structure. The main obstacle in commercialization of biosurfactant especially rhamnolipids is the higher cost of the production. Glycerol is readily available from commercial fat-splitting process in the form of sweet water (up to 20% w/v) at very low cost. Two natural strains of Pseudomonas aeruginosa (ATCC 10145 and ATCC 9027) were compared for rhamnolipid production. The neotype strain of Pseudomonas aeruginosa (ATCC 10145) was found to produce more amounts of rhamnolipids than Pseudomonas aeruginosa (ATCC 9027) on glucose and glycerol as carbon source. The microbial growth (0.94 g/L) and formation of rhamnolipids (2.75 g/L) was maximum at 5% (w/v) glycerol concentration by Pseudomonas aeruginosa (ATCC 10145). The fermentation was monitored for 8 days on shake flask and magnetically stirred batch culture. In magnetically stirred batch culture, microbial growth was 0.69 g/L and 2.73 g/L of rhamnolipid was formed. Sweet water was also used as a source of glycerol.

Surface-active potential of biosurfactants produced in curd whey by Pseudomonas aeruginosa strain-PP2 and Kocuria turfanesis strain-J at extreme environmental conditions

Surface-active potential of biosurfactants produced cost-effectively in curd whey by Pseudomonas aeruginosa strain-PP2 and Kocuria turfanesis strain-J were tested using parameters viz. surface tension (ST) reduction, F(CMC) (highest dilution factor to reach critical micelle concentration) and emulsification index (EI-24) of pesticides; monocrotophos and imidacloprid at extreme environmental conditions. Results have shown that ST reduction of biosurfactants was stable at pH 2-11. High F(CMC) of the biosurfactant in the fermented whey at low pH improved emulsification of pesticides. ST marginally increased at 5% and 15% NaCl, resulting in high EI-24 and F(CMC). Over a range of temperatures 30-121 °C, ST remained low with a higher F(CMC) and EI-24 at 60 °C than at 121 and 30 °C. The biosurfactants have shown differences in their surface-active property and have marked specificity to emulsify pesticides in extreme environmental conditions.

Biosurfactant production by marine bacterial isolates from the Venezuelan Atlantic Front

Our purpose was to detect, isolate and characterize tensioactive agents with or without emulsifying activity from marine bacterial strains present in seawater and sediment samples from the Venezuelan Atlantic Front. Biosurfactants found in cell-free supernatants from all cultures presented high surface activity as they were able to reduce the water surface tension from 72 dynes cm(-1) to values between 41.7 and 33.9 dynes cm(-1). However, high indirect CMC values were registered for the most of these compounds (51.4%-56.1% v/v). Culture supernatants from S3 and S29 strains showed highest emulsifying activity in the dispersion assay with diesel oil (absorbance 1.06 and 1.18, respectively), while supernatant from the S10 strain induced the most stable oil-in-water emulsions with 16° and 25°API crude oils. Only culture supernatant from S3 strain was able to produce stable oil-in water emulsions with diesel oil and both type of crude oils.

Synthesis, characterization, and oil recovery application of biosurfactant produced by indigenous pseudomonas aeruginosa WJ-1 using waste vegetable oils

A bacterial strain was isolated and cultured from the oil excavation areas in tropical zone in northern China. The biochemical characteristics and partial sequenced 16S rRNA gene of isolate, WJ-1, was identical to those of cultured representatives of the species Pseudomonas aeruginosa. This bacterium was able to produce a type of biosurfactant. Compositional analysis revealed that the extracted biosurfactant was composed of high percentage lipid (∼74%, w/w) and carbohydrate (∼20%, w/w) in addition to a minor fraction of protein (∼6%, w/w). The best production of 50.2 g/l was obtained when the cells were grown on minimal salt medium containing 6.0% (w/v) glucose and 0.75% (w/v) sodium nitrate supplemented with 0.1% (v/v) element solution at 37 °C and 180 rpm after 96 h. The optimum biosurfactant production pH value was found to be 6.0-8.0. The biosurfactant of WJ-1, with the critical micelle concentration of 0.014 g/L, could reduce surface tension to 24.5 mN/m and emulsified kerosene up to EI(24) ≈95. The results obtained from time course study indicated that the surface tension reduction and emulsification potential was increased in the same way to cell growth. However, maximum biosurfactant production occurred and established in the stationary growth phase (after 90 h). Thin layer chromatography, Fourier transform infrared spectrum, and mass spectrum analysis indicate the extracted biosurfactant was affiliated with rhamnolipid. The core holder flooding experiments demonstrated that the oil recovery efficiency of strain and its biosurfactant was 23.02% residual oil.

Characterization of a novel biosurfactant produced by Staphylococcus sp. strain 1E with potential application on hydrocarbon bioremediation

A biosurfactant-producing bacterium (Staphylococcus sp. strain 1E) was isolated from an Algerian crude oil contaminated soil. Biosurfactant production was tested with different carbon sources using the surface tension measurement and the oil displacement test. Olive oil produced the highest reduction in surface tension (25.9 dynes cm(-1)). Crude oil presented the best substrate for 1E biosurfactant emulsification activity. The biosurfactant produced by strain 1E reduced the growth medium surface tension below 30 dynes cm(-1). This reduction was also obtained in cell-free filtrates. Biosurfactant produced by strain 1E showed stability in a wide range of pH (from 2 to 12), temperature (from 4 to 55 °C) and salinity (from 0 to 300 g l(-1)) variations. The biosurfactant produced by strain 1E belonged to lipopeptide group and also constituted an antibacterial activity againt the pathogenic bacteria such as Staphylococcus aureus, Escherichia coli, Pseudomonas aeruginosa and Bacillus subtilis. Phenanthrene solubility in water was enhanced by biosurfactant addition. Our results suggest that the 1E biosurfactant has interesting properties for its application in bioremediation of hydrocarbons contaminated sites.

Biosurfactant-producing bacterium, Pseudomonas aeruginosa MA01 isolated from spoiled apples: physicochemical and structural characteristics of isolated biosurfactant

An extensive investigation was conducted to isolate indigenous bacterial strains with outstanding performance for biosurfactant production from different types of spoiled fruits, food-related products and food processing industries. An isolate was selected from 800 by the highest biosurfactant yield in soybean oil medium and it was identified by 16S rRNA and the two most relevant hypervariable regions of this gene; V3 and V6 as Pseudomonas aeruginosa MA01. The isolate was able to produce 12 g/l of a glycolipid-type biosurfactant and generally less efficient to emulsify vegetable oils compared to hydrocarbons and could emulsify corn and coconut oils more than 50%. However, emulsification index (E(24)) of different hydrocarbons including hexane, toluene, xylene, brake oil, kerosene and hexadecane was between 55.8% and 100%. The surface tension of pure water decreased gradually with increasing biosurfactant concentration to 32.5 mNm(-1) with critical micelle concentration (CMC) value of 10.1mg/l. Among all carbon substrates examined, vegetable oils were the most effective on biosurfactant production. Two glycolipid fractions were purified from the biosurfactant crude extracts, and FTIR and ES-MS were used to determine the structure of these compounds. The analysis indicated the presence of three major monorhamnolipid species: R(1)C(10)C(10), R(1)C(10)C(12:1), and R(1)C(10)C(12); as well as another three major dirhamnolipid species: R(2)C(10)C(10), R(2)C(10)C(12:1), and R(2)C(10)C(12). The strain sweep experiment for measuring the linear viscoelastic of biosurfactant showed that typical behavior characteristics of a weak viscoelastic gel, with storage modulus greater than loss modulus at all frequencies examined, both showing some frequency dependence.

From wastewater to bioenergy and biochemicals via two-stage bioconversion processes: a future paradigm

Recovery of bioenergy and biochemicals from wastewater has attracted growing and widespread interests. In this respect, two-stage bioconversion process (TSBP) offers an appealing avenue to achieve stepwise and directional substrate conversion in separated stages. Such a biosystem not only enables enhanced degradation of organics, but also favors a high product yield and quality. Various TSBRs have been developed for the production of methane, hydrogen, electricity, bioplastics, bioflocculants, biopesticides, biosurfactants and other value-added products, demonstrating marked advantages over the conventional one-stage processes. It represents a promising, and likely the sole viable, paradigm for future application. However, there are also many remaining challenges. This paper provides an overview of the various TSBPs, introduces the recent advances, and discusses the major challenges and the future perspectives for practical application.

Genetic regulations of the biosynthesis of microbial surfactants: an overview

Microbial biosurfactants are surface active metabolites synthesized by microbes growing on a variety of substrates. In spite of having great potential for commercial, therapeutic and environmental applications, industrial level production has not been realized for their low yields and productivities. One vital factor determining their biosynthesis is the genetic makeup of the producer organisms. Studies on molecular genetics and biochemistry of the synthesis of several biosurfactants have revealed the operons, the enzymes and the metabolic pathways required for their extracellular production. Surfactin, a cyclic lipopeptide biosurfactant is a potent antimicrobial agent and is produced as a result of non-ribosomal biosynthesis catalyzed by a large multienzyme peptide synthetase complex called the surfactin synthetase. Pathways for the synthesis of other lipopeptides such as iturin, lichenysin and arthrofactin are also mediated by similar enzyme complexes. These non-ribosomal peptide synthetases (NRPSs) responsible for lipopeptide biosynthesis display a high degree of structural similarity among themselves even from distant microbial species. Plasmid-encoded- rhlA, B, R and I genes of rhl quorum sensing system are required for production of glycolipid biosurfactants by Pseudomonas species. Molecular genetics of biosynthesis of alasan and emulsan by Acinetobacter species and of the fungal biosurfactants such as mannosylerythritol lipids (MEL) and hydrophobins have been deciphered. However, limited genetic information is available about biosynthesis of other biosurfactants such as viscosin, amphisin and putisolvin produced by some strains of Pseudomonas species. Understanding of the genetic regulatory mechanisms would help to develop metabolically engineered hyper-producing strains with better product characteristics and acquired capability of utilizing cheap agro-industrial wastes as substrates. This article thus provides an overview of the role and importance of molecular genetics and gene regulation mechanisms behind the biosynthesis of various microbial surfactants of commercial importance.