Microfiber-based few-layer black phosphorus saturable absorber for ultra-fast fiber laser

Few-layer metal monochalcogenide saturable absorbers for high-energy Q-switched pulse generation

Two-dimensional layered materials have been widely utilized as nonlinear absorption materials to transfer continue-wave into pulse trains in fiber laser systems. Here, we prepare robust GaSe/GeSe composites with high power bearing capacity as saturable absorbers (SAs) and then investigate their nonlinear optical properties via broadband Z-scan measurement at 800 nm and 1550 nm, respectively. The modulation depths of GaSe/GeSe based SAs are measured to be 11.97% and 7.69% at 1550 nm. After incorporating the GaSe/GeSe SAs into an Erbium-doped fiber laser cavity, passively Q-switched pulse trains could be obtained with repetition rates changing from 83.58 to 136.78 kHz (70.41 to 161.65 kHz). The maximum output power and pulse energy are 52.1 mW/370.67 nJ (GaSe) and 21.6 mW/133.74 nJ (GeSe) under the maximum pump power of 600 mW. The results indicate that GaSe and GeSe possess outstanding thermal stability and could be employed as remarkable saturable absorption materials for high-energy pulses generation.

Passively Q-switched and mode-locked erbium-doped fiber lasers based on tellurene nanosheets as saturable absorber

Various two-dimensional (2D) materials show unique optical properties and excellent performance in acting as saturable absorber (SA) for demonstrating all-fiber ultra-fast lasers. Tellurene, as a new-fashioned few-layer 2D monoelemental material, was designed as an excellent saturable absorber to achieve Q-switched and mode-locked operations within erbium-doped fiber (EDF) lasers in our experiment. High-quality tellurene-based SA with a modulation depth of 0.97% was obtained by blending few-layer tellurene nanosheet solution prepared by liquid phase exfoliation method and the polyvinyl alcohol (PVA) solution. Inserting the SA into the EDF laser cavity by sandwiching the tellurene-PVA film between two fiber ferrules, either the passively Q-switched or the passively mode-locked operations can be obtained. The repetition rate varies from 15.92 to 47.61 kHz, and the pulse duration decreases from 8.915 to 5.196 µs in the passively Q-switched operation. To the best of our knowledge, this is the first demonstration focusing on the modulation application of tellurene in designing Q-switched pulsed laser operations. Additionally, mode-locked operations were also achieved by adjusting the polarization state. The obtained results fully indicate that tellurene can be developed as an efficient SA for pulsed fiber lasers.

In2Se3 nanosheets for harmonic mode-locked fiber laser

Two-dimensional materials with a sheet structure have excellent optical, electrical and mechanical properties, and have attracted much attention in recent years, especially In₂Se₃ (the N-type semiconductor compound), which has a rapid development in the fields of materials science and optical communication. In this paper, the nonlinear saturation absorption characteristics of In₂Se₃ are studied. The In₂Se₃ nanosheet dispersion can be used in ultrafast photonics applications. The nonlinear absorption is measured by power dependent method, and the modulation depth and saturation intensity are 3.8% and 246.6 MW cm^-2, respectively. More importantly, In₂Se₃ is used as a saturable absorber (SA) in a passively mode-locked erbium-doped fiber laser. The proposed mode-locked fiber laser is demenstrated with a center wavelength of 1529.4 nm, a fundamental frequency of 5.9 MHz, a spectral width of 3.96 nm, a pulse width of 1.38 ps, and a signal-to-noise ratio of 55 dB. For the first time, harmonic mode-locking with a high-repetition rate of 431 MHz is achieved when the pump power is 360 mW corresponding to 73rd-order harmonic mode locking. It can be seen that In₂Se₃ is indeed a new excellent photonic material, which can be used in fiber optic communication, SAs photonics, laser material processing and light modulators.

Detection and elimination of pulse train instabilities in broadband fibre lasers using dispersion scan

We use self-calibrating dispersion scan to experimentally detect and quantify the presence of pulse train instabilities in ultrashort laser pulse trains. We numerically test our approach against two different types of pulse instability, namely second-order phase fluctuations and random phase instability, where the introduction of an adequate metric enables univocally quantifying the amount of instability. The approach is experimentally demonstrated with a supercontinuum fibre laser, where we observe and identify pulse train instabilities due to nonlinear propagation effects under anomalous dispersion conditions in the photonic crystal fibre used for spectral broadening. By replacing the latter with an all-normal dispersion fibre, we effectively correct the pulse train instability and increase the bandwidth of the generated coherent spectrum. This is further confirmed by temporal compression and measurement of the output pulses down to 15 fs using dispersion scan.

Mode-locked and Q-switched mode-locked fiber laser based on a ferroferric-oxide nanoparticles saturable absorber

We demonstrated an ultrafast erbium-doped fiber laser (EDFL) based on ferroferric-oxide (Fe₃O₄) nanoparticles as a saturable absorber (SA). The investigated SA was based on magnetic fluid deposited on the end face of a fiber ferrule connector. When the SA was inserted into an EDFL cavity, a stable 2.93 ps mode-locked pulse can be achieved by adjusting the intra-cavity polarization controller. The pulse had a central wavelength of 1572.39 nm and a 3 dB bandwidth of 1.39 nm. We also obtained Q-switched mode-locked pulses at 1593.4 nm. The repetition frequency and the temporal width of the Q-switched pulse envelope varied with the pump power. When the pump power reached 225 mW, the maximum average output power and the pulse envelope energy were up to 4.51 mW and 235.5 nJ. To the best of our knowledge, this is the first time that mode-locked and Q-switched mode-locked pulses have been obtained in a fiber laser based on Fe₃O₄ nanoparticles.

Niobium disulfide as a new saturable absorber for an ultrafast fiber laser

Group VB transition metal dichalcogenides (TMDCs) are emerging two-dimensional materials and have attracted significant interests in the fields of physics, chemistry, and material sciences. However, there are very few reports about the optical characteristics and ultrafast photonic applications based on group VB TMDCs so far. In this work, we have calculated the niobium disulfide (NbS2) band structure by the density functional theory (DFT), which has revealed that NbS2 is a metallic TMDC. In addition, we have prepared an NbS2-microfiber device and the nonlinear optical characteristics have been investigated. The modulation depth, saturation intensity and non-saturable loss have been measured to be 13.7%, 59.93 MW cm-2 and 17.74%, respectively. Based on the nonlinear optical modulation effect, the Er-doped fiber (EDF) laser works in the soliton mode-locking state with the pump power of 94-413 mW. The pulse duration of 709 fs and the maximum average output power of 23.34 mW have been obtained at the pump power of 413 mW. The slope efficiency is as high as 6.79%. Compared to the recently reported studies based on TMDCs comprehensively, our experimental results are better. These experimental results demonstrate that NbS2 with excellent nonlinear optical properties can be used as a promising candidate to advance the development of ultrafast photonics.

An overview of the optical properties and applications of black phosphorus

Since the year 2014, when scientists first obtained black phosphorus using a sticky tape to peel the layers off, it has attracted tremendous interest as a novel two-dimensional material. After it was successfully produced, its outstanding optical properties have been unveiled. Various applications based on these properties have been reported. This study mainly reviews the unique optical properties and potential applications of black phosphorus. The optical performances of black phosphorus mainly include linear optical properties and nonlinear optical properties. Some examples include the anisotropic optical response, saturable absorption effect and Kerr effect. The researchers found that the nonlinear saturable absorption coefficients of black phosphorus are better than that of MoS₂ and WS₂ from the visible region to the near-infrared region. Compared with graphene, black phosphorus has a better nonlinear saturable absorption performance. After passivation or surface modification, black phosphorus is stable when exposed to oxygen and water. Herein, black phosphorus has the potential to be used in detector/sensors, solar energy harvesting, photocatalysts, optical saturable absorbers in ultrafast lasers, all optical switches, optical modulation, nanomedicine and some others in the near future.

Bismuthene Nanosheets for 1 μm Multipulse Generation

Bismuthene, as a new two-dimensional material made up of diazo metal elements, has drawn massive attention for its unique electronic, mechanical, quantum, and nonlinear optical properties. In recent years, researchers have increasingly turned their attention to the ultrafast photonics fields based on bismuthene. However, the internal ultrashort pulse dynamics has seldom been explored yet. In this work, the nonlinear optical properties of bismuthene nanosheets have been studied and applied in a passively mode-locked fiber laser. The saturation intensity and modulation depth of a saturable absorber (SA) device are about 2.4 MW/cm² and 1%, respectively. Thanks to the narrow band gap of bismuthene and tapered fiber structure, a special kind of noise-like multipulses has been obtained. The evolution of the pulsed laser is also studied. This proposed pulsed fiber laser based on a bismuthene SA device is well suitable for some applications such as material processing, optical logics, and so forth.

Nonlinear optical absorption properties of zirconium selenide in generating dark soliton and dark-bright soliton pairs

Our work reports the preparation of zirconium selenide (ZrSe₂)-polyvinyl alcohol (PVA) film-type saturable absorber (SA) and its nonlinear absorption performance in obtaining dark soliton and dark-bright soliton pairs in an Er-doped fiber (EDF) laser for the first time, to the best of our knowledge. The saturation intensity and modulation depth of the ZrSe₂-PVA SA were ∼12.72MW/cm² and 2.3%, respectively. Due to the modulation of the SA, under a pump power of 525.2 mW, stable dark soliton operation with an average output power of 9.75 mW, and a pulse repetition frequency of 20.84 MHz, a pulse width of 3.85 ns was attained successfully. By adjusting the state of the polarization controllers, dark-bright soliton pairs were also observed. To the best of our knowledge, this was the first demonstration focusing on the nonlinear optical absorption applications of ZrSe₂ in obtaining dark soliton and dark-bright soliton pairs. Our results show that ZrSe₂ is a good two-dimensional SA material for acting as an ultrafast optical device due to its suitable nonlinear optical absorption properties.

Tunable and Anisotropic Dual-Band Metamaterial Absorber Using Elliptical Graphene-Black Phosphorus Pairs

We numerically propose a dual-band absorber in the infrared region based on periodic elliptical graphene-black phosphorus (BP) pairs. The proposed absorber exhibits near-unity anisotropic absorption for both resonances due to the combination of graphene and BP. Each of the resonances is independently tunable via adjusting the geometric parameters. Besides, doping levels of graphene and BP can also tune resonant properties effectively. By analyzing the electric field distributions, surface plasmon resonances are observed in the graphene-BP ellipses, contributing to the strong and anisotropic plasmonic response. Moreover, the robustness for incident angles and polarization sensitivity are also illustrated.

In2Se3 nanosheets with broadband saturable absorption used for near-infrared femtosecond laser mode locking

Indium selenide (In₂Se₃) has attracted tremendous attention due to its favorable electronic features, broad tunable bandgap, high stability and other attractive properties. However, its further applications for nonlinear optics have not yet been fully explored. In this work, we demonstrate that few-layer α-In₂Se₃ nanosheets exhibit strong saturable absorption properties over a wide wavelength range covering 800, 1064 and 1550 nm. The few-layer α-In₂Se₃ nanosheets used for this experiment are fabricated via a simple ultrasonic exfoliation in liquid. Stable ultrafast mode-locking laser pulses are obtained from both ytterbium-doped and erbium-doped fiber laser systems operating at 1064 and 1550 nm, respectively. A pulse duration as short as 215 fs was achieved in the Er-doped fiber laser system. Stable output pulses over 6 h of operation were obtained in both laser systems. The pulse energy and peak power of the laser output pulses were increased by reducing the In₂Se₃ thickness. These results indicate that α-In₂Se₃ nanosheets with low layer numbers are promising candidates for broad ultrafast photonics devices, such as optical switchers, Q-switchers and mode lockers.

Nonlinear Optical Properties of Zirconium Diselenide and Its Ultra-Fast Modulator Application

Recently, two-dimensional (2D) materials have been widely studied by researchers due to their exceptional 2D structure and excellent optical characteristics. As one of the typically-layered 2D transition metal dichalcogenide (TMD) semiconductors from group IVB with a bandgap value of 0.9–1.2 eV (bulk to monolayer), the characteristics of zirconium diselenide (ZrSe₂) have already been extensively investigated in many fields. However, the nonlinear absorption properties of ZrSe₂ in ultra-fast lasers have not been previously demonstrated. In this work, we measured various parameters in order to investigate the characteristics of the nonlinear saturable absorption of ZrSe₂. A ZrSe₂–polyvinyl alcohol (PVA) film was successfully prepared, which was employed as a saturable absorber (SA) to demonstrate, for the first time, an erbium (Er)-doped passive mode-locking fiber laser with a ring cavity. The saturation intensity of the ZrSe₂–PVA film-type SA is 12.72 MW/cm², while its modulation depth is 2.3%. The stable soliton state with a maximum output power of 11.37 mW and a narrowest monopulse duration of 12.5 ps at a repetition frequency of 21.22 MHz was detected. The experimental results conclusively proved that ZrSe₂, with its suitable bandgap value and excellent nonlinear absorption properties, as well as its high damage threshold, should have extensive potential applications within the field of ultra-fast pulse lasers.

Improved Laser Damage Threshold of In2Se3 Saturable Absorber by PVD for High-Power Mode-Locked Er-Doped Fiber Laser

In this study, a double-end pumped high-power passively mode-locked erbium-doped fiber laser (EDFL) was realized by employing a few-layered In₂Se₃ flakes as a saturable absorber (SA). Herein, the uniform large-scale In₂Se₃ flakes were synthesized by the physical vapor deposition (PVD) method. The PVD-In₂Se₃ SA exhibited a remarkable damage threshold of higher than 24 mJ/cm². Meanwhile, the PVD-In₂Se₃ SA had a modulation depth and saturable intensity of 18.75% and 6.8 MW/cm², respectively. Based on the In₂Se₃ SA, the stable bright pulses emitting at 1559.4 nm with an average output power/pulse energy/pulse duration of 122.4 mW/5.8 nJ/14.4 ns were obtained successfully. To our knowledge, 122.4 mW was the new major breakthrough of mode-locked Er-doped fiber lasers. In addition, this is the first demonstration of the dark-bright pulse pair generation based on In₂Se₃ SA. The maximum average output power of the dark-bright pulse reached 121.2 mW, which also showed significant enhancement in comparison with previous works. Our excellent experiment results fully prove the superiority of our experimental design scheme and indicate that the PVD-In₂Se₃ could operate as a promising highly-nonlinear photonic material for a high-power fiber laser.

Output energy enhancement in a mode-locked Er-doped fiber laser using CVD-Bi2Se3 as a saturable absorber

In this study, the output energy in topological insulators (TIs)-based Erbium-doped fiber laser (EDFL) was improved using two strategies: bidirectional pumped laser cavity and saturable absorber (SA) with high damage threshold and large modulation depth. Using the chemical vapor deposition (CVD) method, Bismuth Selenide (Bi₂Se₃) film was synthesized and improved to a SA. Employing this CVD-Bi₂Se₃ SA in an EDFL, bright and bright-dark soliton operations were achieved. The average output power/pulse energy was 82.6 mW/48.3 nJ and 81.2 mW/47.5 nJ, respectively. The results demonstrate that CVD-Bi₂Se₃ can act as an excellent performance material to improve output power performance in TISA-based EDFL.

Lead monoxide: a promising two-dimensional layered material for applications in nonlinear photonics in the infrared band

Lead monoxide (PbO), a novel few-layer two-dimensional (2D) material, was theoretically predicted to have an excellent optical response. Herein, the nonlinear optical response of PbO in the infrared region was experimentally investigated. The feasibility of PbO nanosheets as an effective optical saturable absorber was experimentally verified for the first time. Based on the excellent nonlinear optical characteristics, 2D PbO was fabricated as a passive mode locker by depositing onto a fiber patch cord and by decorating on a microfiber, both of which were successfully applied in fiber lasers for the passive mode locking operation. The mode locking pulses of the fiber laser were as short as 650 fs at 1.5 μm. A pulse duration of 5.47 ps with a 1 μm fiber laser was also experimentally verified. Finally, a PbO-decorated microfiber was fabricated as an optical thresholder that can enhance the SNR of a 1 GHz signal up to 6 dB. This finding might facilitate the development of nonlinear photonic devices with high stability and their practical applications in the future.

All-optical signal processing in few-layer bismuthene coated microfiber: towards applications in optical fiber systems

Two-dimensional (2D) bismuthene can find its wide potential applications due to its appealing optical and electronic properties. Especially, bismuthene exhibits layer-count dependent direct bandgaps and strong light-matter interaction, enabling its applications in all-optical signal processing area that can overcome the bottle-neck in existing electrical signal processing. However, light-bismuthene interaction based on main stream optical fiber systems and its application in all-optical signal processing is relatively less investigated. In this work, few-layer bismuthene, synthesized with facile solution processing method, is coated onto a piece of microfiber. The experimental results show that this device can operate as an optical Kerr switcher and a four-wave-mixing-based wavelength converter under different configuration. The results including wavelength applicability, information bandwidth, eye diagrams in combination with bit-error rate (BER) performance and stability measurements confirm its feasibility in optical fiber systems. To the best of our knowledge, it is first prototypic device reported in this work for bismuthene in all-optical signal processing optical fiber systems.

Near-Infrared Optical Modulation for Ultrashort Pulse Generation Employing Indium Monosulfide (InS) Two-Dimensional Semiconductor Nanocrystals

In recent years, metal chalcogenide nanomaterials have received much attention in the field of ultrafast lasers due to their unique band-gap characteristic and excellent optical properties. In this work, two-dimensional (2D) indium monosulfide (InS) nanosheets were synthesized through a modified liquid-phase exfoliation method. In addition, a film-type InS-polyvinyl alcohol (PVA) saturable absorber (SA) was prepared as an optical modulator to generate ultrashort pulses. The nonlinear properties of the InS-PVA SA were systematically investigated. The modulation depth and saturation intensity of the InS-SA were 5.7% and 6.79 MW/cm2, respectively. By employing this InS-PVA SA, a stable, passively mode-locked Yb-doped fiber laser was demonstrated. At the fundamental frequency, the laser operated at 1.02 MHz, with a pulse width of 486.7 ps, and the maximum output power was 1.91 mW. By adjusting the polarization states in the cavity, harmonic mode-locked phenomena were also observed. To our knowledge, this is the first time an ultrashort pulse output based on InS has been achieved. The experimental findings indicate that InS is a viable candidate in the field of ultrafast lasers due to its excellent saturable absorption characteristics, which thereby promotes the ultrafast optical applications of InX (X = S, Se, and Te) and expands the category of new SAs.

Excessively tilted fiber grating based Fe3O4 saturable absorber for passively mode-locked fiber laser

A novel approach to saturable absorber (SA) formation is presented by taking advantage of the mode coupling property of excessively tilted fiber grating (Ex-TFG). Stable mode-locked operation can be conveniently achieved based on the interaction between Ex-TFG coupled light and deposited ferroferric-oxide (Fe₃O₄) nanoparticles. The central wavelength, bandwidth and single pulse duration of the output are 1595 nm, 4.05 nm, and 912 fs, respectively. The fiber laser exhibits good long-term stability with signal-to-noise ratio (SNR) of 67 dB. For the first time, to the best of our knowledge, Ex-TFG based Fe₃O₄ SA for mode-locked fiber laser is demonstrated.

Nonlinear Absorption Properties of Cr2Ge2Te6 and Its Application as an Ultra-Fast Optical Modulator

In this manuscript, the nonlinear absorption properties of Cr₂Ge₂Te₆ and its application in ultra-fast optical modulation are investigated. Typical parameters, namely, nonlinear absorption coefficient (β), saturation intensity, and modulation depth are measured to be ~1.66 × 10⁻⁹ m/W, 15.3 MW/cm², and 5.8%, respectively. To investigate the feasibility of using the Cr₂Ge₂Te₆ as an ultra-fast optical modulator, a ring-cavity passively mode-locked Er-doped fiber laser has been constructed. The output power/pulse, duration/pulse, and repetition rate/signal-to-noise ratios for the stable mode-locked operation are 2.88 mW/881 fs/19.33 MHz/48 dB, respectively, which proves that the Cr₂Ge₂Te₆ has outstanding nonlinear optical properties and advantages in performing as an ultra-fast optical modulator. Further, the experimental results provide valuable references and open new avenues for developing two-dimensional, material-based, ultra-fast optical modulators and advanced photonic devices based on Cr₂Ge₂Te₆.

Versatile Mode-Locked Operations in an Er-Doped Fiber Laser with a Film-Type Indium Tin Oxide Saturable Absorber

We demonstrate the generation of versatile mode-locked operations in an Er-doped fiber laser with an indium tin oxide (ITO) saturable absorber (SA). As an epsilon-near-zero material, ITO has been only used to fashion a mode-locked fiber laser as an ITO nanoparticle-polyvinyl alcohol SA. However, this type of SA cannot work at high power or ensure that the SA materials can be transmitted by the light. Thus, we covered the end face of a fiber with a uniform ITO film using the radio frequency magnetron sputtering technology to fabricate a novel ITO SA. Using this new type of SA, single-wavelength pulses, dual-wavelength pulses, and triple-wavelength multi-pulses were achieved easily. The pulse durations of these mode-locked operations were 1.67, 6.91, and 1 ns, respectively. At the dual-wavelength mode-locked state, the fiber laser could achieve an output power of 2.91 mW and a pulse energy of 1.48 nJ. This study reveals that such a proposed film-type ITO SA has excellent nonlinear absorption properties, which can promote the application of ITO film for ultrafast photonics.

Large-energy mode-locked ytterbium-doped linear-cavity fiber laser based on chemical vapor deposition-Bi2Se3 as a saturable absorber

We reported on the generation of pulse bunch and large-energy dark pulses in a mode-locked ytterbium-doped linear-cavity fiber laser based on Bi₂Se₃ as a saturable absorber (SA). Bi₂Se₃ nanosheets were successfully synthesized by the chemical vapor deposition (CVD) method and transferred to the end facet of a fiber connector for the proposed SA. Its saturation intensity and modulation depth were measured to be 52  MW/cm² and 14.5%, respectively. By inserting the Bi₂Se₃-based SA into the Yb-doped all-fiber linear cavity, stable pulse bunches were observed. In addition, dark soliton operation with a maximum average output power of 32.6 mW and a pulse energy of 61.8 nJ were also achieved. To the best of our knowledge, this is the first demonstration of a dark soliton within a linear cavity with much larger pulse energy than previous works. Our study fully indicated that CVD-Bi₂Se₃ could be an excellent SA for achieving large-energy pulse operations.

A pulsewidth measurement technology based on carbon-nanotube saturable absorber

We demonstrate a proof-of-concept saturable absorption based pulsewidth measurement (SAPM) by exploring the intensity dependent nonlinear transmission (i.e., saturable absorption) of low-dimensional material (LDM) carbon nanotubes. A minimum pulse energy of 75 fJ is experimentally detected with an average-power-peak-power product (P_av⋅ P_pk) of 5.44×10^-7 W² near 1550 nm. A minimum detectable pulse energy of 10 fJ with a P_av⋅ P_pk of 1.3×10^-9 W² is estimated with further optimization. The nanometer-level thickness and femtosecond-level decay time of LDMs allow ultrafast light interaction on a very small footprint, which potentially supports chip-scale characterization of ultrafast pulses with minimum distortion.

Anisotropic infrared plasmonic broadband absorber based on graphene-black phosphorus multilayers

Two-dimensional materials (2DMs) such as graphene and black phosphorus (BP) have aroused considerable attentions in the past few years. Engineering and enhancing their light-matter interaction is possible due to their support for localized surface plasmon resonances in the infrared regime. In this paper, we have proposed an infrared broadband absorber consisting of multilayer graphene-BP nanoparticles sandwiched between dielectric layers. Benefiting from the properties of graphene and BP, the absorber exhibits both perfect broadband responses and strong anisotropy beyond individual graphene and BP layers. The absorber is tunable with the variation of geometric parameters as well as the doping levels of graphene and BP. The physical insight is revealed by electric field distributions. Furthermore, the angular robustness for incident wave is investigated. The proposed anisotropic omnidirectional broadband absorber may have promising potential applications in various biosensing, communication and imaging systems.

Ultra-stable pulse generation in ytterbium-doped fiber laser based on black phosphorus

We demonstrated a high-quality black phosphorus (BP) crystal fabricated via a modified electrochemical delamination exfoliation process. Employing the nonlinear transmittance method and Z-scan technique, the nonlinear optical properties of BP were characterized. Based on the saturable absorber (SA) of BP, we designed a passively Q-switched ytterbium (Yb)-doped fiber laser operating at 1.06 μm. Additionally, the pulse laser could operate stably for at least 69 days. These experimental results indicate that the modified BP is an ultra-stable and promising optical modulation material for ultrashort pulse generation in Yb-doped fiber lasers.

Lifetime and nonlinearity of modulated surface plasmon for black phosphorus sensing application

Black phosphorus surface plasmon (BPSP) is a new promising candidate material for electromagnetic field confinement at the subwavelength scale. Here, we theoretically investigated the light confinement, second-order nonlinearity and lifetimes of tunable surface plasmons in nanostructured black phosphorus nanoflakes with superstrates. The grating structure can enhance the local optical field of the fundamental wave (FW) and second harmonic wave (SHW) due to the surface plasmon resonance. Based on the coupled mode theory (CMT), a theoretical model for the nanostructured black phosphorus was established to study the spectrum features of FW. The lifetimes of the plasmonic resonant modes were investigated with the finite difference time domain (FDTD) simulations and CMT. Since the permittivity of black phosphorus depends on its Fermi energy and electron scattering rate, the lifetimes of plasmonic absorption modes are tunable with both the Fermi energy and scattering rate. The intensity, wavelengths and spectral width of BPSP resonance modes and their lifetimes can be precisely controlled with the Fermi energy, scattering rate, side length and refractive index of the superstrate. The sensitivity is described by varying the refractive index of the superstrate such as an aqueous solution. We have introduced a second-order nonlinear source to investigate the SHW of nanostructured black phosphorus. This paper presents the corner/edge energy distribution and the tunable lifetime of BPSP as well as their unprecedented capability of photon manipulation for second-order nonlinearity within the deep subwavelength scale. The configuration and method are useful for research of the absorption, lifetime of light and nonlinear optical processes in black phosphorus-based optoelectronic devices, especially the modulation and sensing applications.

Various large-energy soliton operations within an Er-doped fiber laser with bismuth selenide as a saturable absorber

Different large-energy mode-locked operations were successfully obtained within a Bi₂Se₃-based Er-doped fiber laser. First, mode-locked operation with maximum pulse energy of 17.2 nJ and pulse width of 187 ns under a pulse repetition rate of 537.6 kHz was obtained under the pump power of 680 mW. In addition, the characteristics of dark solitons and soliton rains, which also exhibit large pulse energies, have been investigated experimentally. Our results fully proved that Bi₂Se₃ was an excellent candidate for investigating various mode-locked operations with large pulse energy due to its high nonlinear effect and high damage threshold.

Silicon-Phosphorene Nanocavity-Enhanced Optical Emission at Telecommunications Wavelengths

Generating and amplifying light in silicon (Si) continues to attract significant attention due to the possibility of integrating optical and electronic components in a single material platform. Unfortunately, silicon is an indirect band gap material and therefore an inefficient emitter of light. With the rise of integrated photonics, the search for silicon-based light sources has evolved from a scientific quest to a major technological bottleneck for scalable, CMOS-compatible, light sources. Recently, emerging two-dimensional materials have opened the prospect of tailoring material properties based on atomic layers. Few-layer phosphorene, which is isolated through exfoliation from black phosphorus (BP), is a great candidate to partner with silicon due to its layer-tunable direct band gap in the near-infrared where silicon is transparent. Here we demonstrate a hybrid silicon optical emitter composed of few-layer phosphorene nanomaterial flakes coupled to silicon photonic crystal resonators. We show single-mode emission in the telecommunications band of 1.55 μm ( E_g = 0.8 eV) under continuous wave optical excitation at room temperature. The solution-processed few-layer BP flakes enable tunable emission across a broad range of wavelengths and the simultaneous creation of multiple devices. Our work highlights the versatility of the Si-BP material platform for creating optically active devices in integrated silicon chips.

Ultrasensitive optical sensing in aqueous solution based on microfiber modal interferometer

In this paper, an ultrahigh sensitivity sensing in aqueous solution for microfiber modal interferometer (MMI) is realized. The group refractive index (RI) difference between HE₁₁ and HE₁₂ mode will come down to 0 at a certain wavelength, resulting in ultrahigh sensitivity near this wavelength. MMI with different diameters have their individual ultrasensitive wavelength band, which indicates the broad range of optional probing wavelength and more liberal diameter condition on fiber fabrication. In the experimentation, infrared absorption band in water around 1360-1600nm is easy to keep away by adjusting the microfiber diameter. As a result, an ultrahigh sensitivity of 14.95 pm/ppm is realized for sodium nitrate at 1320nm, whose equivalent sensitivity is about 1.26 × 10⁵-nm/RIU for RI, which is much higher than most of the existing naked sensors with magnitude of 10²-10⁴nm/RIU.

Sub-200 fs soliton mode-locked fiber laser based on bismuthene saturable absorber

Few-layer bismuthene is an emerging two-dimensional material in the fields of physics, chemistry, and material science. However, its nonlinear optical property and the related photonics device have been seldom studied so far. Here, we demonstrate a sub-200 fs soliton mode-locked erbium-doped fiber laser (EDFL) using a microfiber-based bismuthene saturable absorber for the first time, to the best of our knowledge. The bismuthene nanosheets are synthesized by the sonochemical exfoliation method and transferred onto the taper region of a microfiber by the optical deposition method. Stable soliton pulses centered at 1561 nm with the shortest pulse duration of about 193 fs were obtained. Our findings unambiguously imply that apart from its fantastic electric and thermal properties, few-layer bismuthene may also possess attractive optoelectronic properties for nonlinear photonics, such as mode-lockers, Q-switchers, optical modulators and so on.

Acetone improves the topographical homogeneity of liquid phase exfoliated few-layer black phosphorus flakes

Liquid phase exfoliation of 2D materials has issues related to the sorption of the solvent, the oxidation of the sample during storage, and the topographical inhomogeneity of the exfoliated material. N-methyl-2-pyrrolidone (NMP), a common solvent for black phosphorus (BP) exfoliation, has additional drawbacks like the formation of by-products during sonication and poor solvent volatility. Here we demonstrate an improvement in the topographical homogeneity (i.e. thickness and lateral dimensions) of NMP-exfoliated BP flakes after resuspension in acetone. The typical size of monolayers and bilayers stabilised in acetone was 99.8 ± 27.4 nm and 159.1 ± 57 nm, respectively. These standard deviations represent a threefold improvement over those of the NMP-exfoliated originals. Phosphorene can also be exfoliated directly in acetone by very long ultrasonication. The product suspension enjoys the same dimensional homogeneity benefits, which confirms that this effect is an intrinsic property of the acetone-BP system. The quality and stability of the exfoliated flakes was checked by XRD, TEM, electron diffraction and Raman spectroscopy. Thermal expansion coefficients of the [Formula: see text] B_2g and [Formula: see text] Raman modes were calculated for drop-casted samples as -0.018 28 cm^-1 K^-1, -0.030 56 cm^-1 K^-1 and -0.032 19 cm^-1 K^-1, respectively. The flakes withstand 20 min in O₂ flow at 373 K without lattice distortion.

Mode-locked thulium-doped fiber laser with chemical vapor deposited molybdenum ditelluride

A passively mode-locked thulium-doped fiber (TDF) laser was realized by employing chemical vapor deposited few-layer molybdenum ditelluride (MoTe₂) as a saturable absorber (SA). The few-layer MoTe₂ film was transferred onto the waist of a microfiber and then incorporated into a TDF laser with a typical all-fiber ring cavity configuration. Stable soliton pulses emitting at 1930.22 nm were obtained with a 3 dB bandwidth of 4.45 nm, a pulse duration of 952 fs, and an average power of 36.7 mW.

Mode-locked Er-doped fiber laser based on PbS/CdS core/shell quantum dots as saturable absorber

Previously, PbS/CdS core/shell quantum dots with excellent optical properties have been widely used as light-harvesting materials in solar cell and biomarkers in bio-medicine. However, the nonlinear absorption characteristics of PbS/CdS core/shell quantum dots have been rarely investigated. In this work, PbS/CdS core/shell quantum dots were successfully employed as nonlinear saturable absorber (SA) for demonstrating a mode-locked Er-doped fiber laser. Based on a film-type SA, which was prepared by incorporating the quantum dots with the polyvinyl alcohol (PVA), mode-locked Er-doped operation with a pulse width of 54 ps and a maximum average output power of 2.71 mW at the repetition rate of 3.302 MHz was obtained. Our long-time stable results indicate that the CdS shell can effectively protect the PbS core from the effect of photo-oxidation and PbS/CdS core/shell quantum dots were efficient SA candidates for demonstrating pulse fiber lasers due to its tunable absorption peak and excellent saturable absorption properties.

Electrostatic Functionalization and Passivation of Water-Exfoliated Few-Layer Black Phosphorus by Poly Dimethyldiallyl Ammonium Chloride and Its Ultrafast Laser Application

Few-layer black phosphorus (BP) which exhibits excellent optical and electronic properties, has great potential applications in nanodevices. However, BP inevitably suffers from the rapid degradation in ambient air because of the high reactivity of P atoms with oxygen and water, which greatly hinders its wide applications. Herein, we demonstrate the electrostatic functionalization as an effective way to simultaneously enhance the stability and dispersity of aqueous phase exfoliated few-layer BP. The poly dimethyldiallyl ammonium chloride (PDDA) is selected to spontaneously and uniformly adsorb on the surface of few-layer BP via electrostatic interaction. The positive charge-center of the N atom of PDDA, which passivates the lone-pair electrons of P, plays a critical role in stabilizing the BP. Meanwhile, the PDDA could serve as hydrophilic ligands to improve the dispersity of exfoliated BP in water. The thinner PDDA-BP nanosheets can stabilize in both air and water even after 15 days of exposure. Finally, the uniform PDDA-BP-polymer film was used as a saturable absorber to realize passive mode-locking operations in a fiber laser, delivering a train of ultrafast pulses with the duration of 1.2 ps at 1557.8 nm. This work provides a new way to obtain highly stable few-layer BP, which shows great promise in ultrafast optics application.

Black Phosphorus and its Biomedical Applications

Black phosphorus (BP), also known as phosphorene, has attracted recent scientific attention since its first successful exfoliation in 2014 owing to its unique structure and properties. In particular, its exceptional attributes, such as the excellent optical and mechanical properties, electrical conductivity and electron-transfer capacity, contribute to its increasing demand as an alternative to graphene-based materials in biomedical applications. Although the outlook of this material seems promising, its practical applications are still highly challenging. In this review article, we discuss the unique properties of BP, which make it a potential platform for biomedical applications compared to other 2D materials, including graphene, molybdenum disulphide (MoS2), tungsten diselenide (WSe2) and hexagonal boron nitride (h-BN). We then introduce various synthesis methods of BP and review its latest progress in biomedical applications, such as biosensing, drug delivery, photoacoustic imaging and cancer therapies (i.e., photothermal and photodynamic therapies). Lastly, the existing challenges and future perspective of BP in biomedical applications are briefly discussed.

High-peak-power mode-locking pulse generation in a dual-loss-modulated laser with BP-SA and EOM

In this Letter, a high-quality black phosphorus saturable absorber (BP-SA) with a multilayer structure was prepared, and its corresponding characteristics were investigated. Based on the BP-SA and an electro-optic modulator (EOM), a dual-loss-modulated mode-locked laser with a controllable repetition rate and high peak power was realized, which has the repetition rate of EOM and the mode-locking pulse width in the Q-switching and mode-locking laser. The output performances versus the pump power were measured. The maximum pulse peak power of 3.89 MW was obtained with the minimum pulse duration of 119 ps. To the best of our knowledge, this is the highest pulse peak power with BP-SA reported.

Large-area and highly crystalline MoSe2 for optical modulator

Transition metal dichalcogenides (TMDs) have been successfully used as broadband optical modulator materials for pulsed fiber laser systems. However, the nonlinear optical absorptions of exfoliated TMDs are strongly limited by their nanoflakes morphology with uncontrollable lateral size and thickness. In this work, we provide an effective method to fully explore the nonlinear optical properties of MoSe₂. Large-area and high quality lattice MoSe₂ grown by chemical vapor deposition method was adopted as an optical modulator for the first time. The large-area MoSe₂ shows excellent nonlinear optical absorption with a large modulation depth of 21.7% and small saturable intensity of 9.4 MW cm^-2. After incorporating the MoSe₂ optical modulator into fiber laser cavity as a saturable absorber, a highly stable Q-switching operation with single pulse energy of 224 nJ is achieved. The large-area MoSe₂ possessing superior nonlinear optical properties compared to exfoliated nanoflakes affords possibility for the larger-area two-dimensional materials family as high performance optical devices.

Passivation of black phosphorus saturable absorbers for reliable pulse formation of fiber lasers

Black phosphorus (BP) has attracted increasing attention due to its unique electrical properties. In addition, the outstanding optical nonlinearity of BP has been demonstrated in various ways. Its functionality as a saturable absorber, in particular, has been validated in demonstrations of passive mode-locked lasers. However, normally, the performance of BP is degraded eventually by both thermal and chemical damage in ambient conditions. The passivation of BP is the critical issue to guarantee a stable performance of the optical devices. We quantitatively characterized the mode-locked lasers operated by BP saturable absorbers with diversified passivation materials such as polydimethylsiloxane (PDMS) or Al₂O₃, considering the atomic structure of the materials, and therefore the hydro-permeability of the passivation layers. Unlike the BP layers without passivation, we demonstrated that the Al₂O₃-passivated BP layer was protected from the surface oxidation reaction in the long-term, and the PDMS-passivated one had a short-term blocking effect. The quantitative analysis showed that the time-dependent characteristics of the pulsed laser without passivation were changed with respect to the pulse duration, spectral width, and time-bandwidth product displaying 550 fs, 2.8 nm, and 0.406, respectively. With passivation, the changes were limited to <43 fs, <0.3 nm, and <0.012, respectively.

Dual-band and polarization-independent infrared absorber based on two-dimensional black phosphorus metamaterials

Two-dimensional (2D) black phosphorus (BP) with direct band gap, bridges the characteristics of graphene with a zero or near-zero band gap and transition metal dichalcogenides with a wide band gap. In the infrared (IR) regime, 2D BP materials can attenuate electromagnetic energy due to losses derived from its surface conductivity. This paper proposes an IR absorber based on 2D BP metamaterials. It consists of multi-layer BP-based nano-ribbon pairs, each formed by two orthogonally stacked nano-ribbons. The multi-layer BP metamaterials and bottom gold mirror together form a Fabry-Perot resonator that could completely inhibit light transmission to create strong absorption through the BP metamaterials. Unlike previously reported BP metamaterial absorbers, this new structure can operate at two frequency bands with absorption > 90% in each owning to the first-order and second-order Fabry-Perot resonant frequencies. It is also polarization independent due to the fourfold rotational structural symmetry. To our best knowledge, this is the first report on using BP metamaterials in an absorber that operates independent of polarization and in dual bands.

Passively mode-locked 1.34 μm bulk laser based on few-layer black phosphorus saturable absorber

By using few-layer black phosphorus (BP) as saturable absorber, an efficient mode-locked Nd:GdVO₄ bulk laser operating at 1.34 μm was realized. An average output power of 350 mW was achieved with a slope efficiency of 15%. The corresponding mode-locking pulse repetition rate, pulse duration and pulse energy were 58.14 MHz, 9.24 ps and 3.0 nJ, respectively. To the best of our knowledge, the pulse width is the shortest among the mode-locked 1.34 μm neodymium lasers ever obtained with other two-dimensional materials saturable absorber. The results clearly indicate the few-layered BP is a kind of promising saturable absorber for ultrafast 1.34 μm lasers.

Black phosphorus flakes covered microfiber for Q-switched ytterbium-doped fiber laser

We demonstrate a passively Q-switched ytterbium-doped fiber laser based on black phosphorus (BP) flakes covered microfiber. The BP saturable absorber is fabricated by sandwiching a microfiber between two pieces of polydimethylsiloxane supported BP flakes film, which is prepared by the mechanical exfoliation method. In this case the BP flakes can be well protected from the action of air and moisture. By incorporating BP flakes covered microfiber into a ytterbium-doped ring fiber laser, stable and reliable Q-switched operation at 1064 nm can be realized via interaction between few-layers BP flakes and the evanescent field of the laser. The laser allows Q-switched pulse generation with a repetition rate in the range of 26-76 kHz and a pulse duration in the range of 5.5-2.0 μs, by varying the pump power from 38 mW to 100 mW.

Intermode beating mode-locking technique for a rare-earth-doped fiber pulsed laser

In this paper, we report the intermode beating mode-locking of a 2  μm Tm³⁺-doped fiber laser (TDFL) pumped by a 1565 nm continuous-wave multi-longitudinal-mode laser. Because strong intermode beating of the 1565 nm pump source induces the periodic modulation of 2 μm intracavity power, stable mode-locking of the TDFL is successfully established by precisely matching the 2 μm cavity frequency with the intermode-beating frequency of the 1565 nm pump source. The mode-locked laser, without requiring any specific mode-locking element, can stably emit the rectangular nanosecond pulses. The mode-locking operation at the center wavelength of 1980.35 nm has a >61  dB signal-to-noise ratio and a 34.496 MHz repetition rate. Although the preliminary results are not better than those of conventional mode-locking, intermode beating mode-locking in combination with rare-earth-doped fiber lasers could provide a promising and alternative solution for compact, low-cost, and high-performance pulsed laser sources.

All-optical phase shifter and switch near 1550nm using tungsten disulfide (WS2) deposited tapered fiber

All-optical phase shifters and switches play an important role for various all-optical applications including all-optical signal processing, sensing and communication. In this paper, we demonstrate a fiber all-optical phase shifter using few-layer 2D material tungsten disulfide (WS₂) deposited on a tapered fiber. WS₂ absorbs injected 980 nm pump (control light) and generates heat, which changes the refractive index of both WS₂ and tapered fiber due to thermo-optic effect and achieves a maximum phase shift of 6.1π near 1550 nm. The device has a loss of 3.7 dB. By constructing a Mach-Zehnder interferometer with WS₂ based phase shifter in one arm, an all-optical switch is also obtained with an extinction ratio of 15 dB and a rise time of 7.3 ms. This all fiber low-cost and compact optical phase shifter and switch demonstrates the potential of 2D transition metal dichalcogenides for all-optical signal processing devices.

Emerging Trends in Phosphorene Fabrication towards Next Generation Devices

The challenge of science and technology is to design and make materials that will dominate the future of our society. In this context, black phosphorus has emerged as a new, intriguing two-dimensional (2D) material, together with its monolayer, which is referred to as phosphorene. The exploration of this new 2D material demands various fabrication methods to achieve potential applications- this demand motivated this review. This article is aimed at supplementing the concrete understanding of existing phosphorene fabrication techniques, which forms the foundation for a variety of applications. Here, the major issue of the degradation encountered in realizing devices based on few-layered black phosphorus and phosphorene is reviewed. The prospects of phosphorene in future research are also described by discussing its significance and explaining ways to advance state-of-art of phosphorene-based devices. In addition, a detailed presentation on the demand for future studies to promote well-systemized fabrication methods towards large-area, high-yield and perfectly protected phosphorene for the development of reliable devices in optoelectronic applications and other areas is offered.

Few-Layer Black Phosphorus Carbide Field-Effect Transistor via Carbon Doping

Black phosphorus carbide (b-PC) is a new family of layered semiconducting material that has recently been predicted to have the lightest electrons and holes among all known 2D semiconductors, yielding a p-type mobility (≈10⁵ cm² V^-1 s^-1 ) at room temperature that is approximately five times larger than the maximum value in black phosphorus. Here, a high-performance composite few-layer b-PC field-effect transistor fabricated via a novel carbon doping technique which achieved a high hole mobility of 1995 cm² V^-1 s^-1 at room temperature is reported. The absorption spectrum of this material covers an electromagnetic spectrum in the infrared regime not served by black phosphorus and is useful for range finding applications as the earth atmosphere has good transparency in this spectral range. Additionally, a low contact resistance of 289 Ω µm is achieved using a nickel phosphide alloy contact with an edge contacted interface via sputtering and thermal treatment.

2D Materials for Optical Modulation: Challenges and Opportunities

Owing to their atomic layer thickness, strong light-material interaction, high nonlinearity, broadband optical response, fast relaxation, controllable optoelectronic properties, and high compatibility with other photonic structures, 2D materials, including graphene, transition metal dichalcogenides and black phosphorus, have been attracting increasing attention for photonic applications. By tuning the carrier density via electrical or optical means that modifies their physical properties (e.g., Fermi level or nonlinear absorption), optical response of the 2D materials can be instantly changed, making them versatile nanostructures for optical modulation. Here, up-to-date 2D material-based optical modulation in three categories is reviewed: free-space, fiber-based, and on-chip configurations. By analysing cons and pros of different modulation approaches from material and mechanism aspects, the challenges faced by using these materials for device applications are presented. In addition, thermal effects (e.g., laser induced damage) in 2D materials, which are critical to practical applications, are also discussed. Finally, the outlook for future opportunities of these 2D materials for optical modulation is given.

Emerging Low-Dimensional Materials for Nonlinear Optics and Ultrafast Photonics

Low-dimensional (LD) materials demonstrate intriguing optical properties, which lead to applications in diverse fields, such as photonics, biomedicine and energy. Due to modulation of electronic structure by the reduced structural dimensionality, LD versions of metal, semiconductor and topological insulators (TIs) at the same time bear distinct nonlinear optical (NLO) properties as compared with their bulk counterparts. Their interaction with short pulse laser excitation exhibits a strong nonlinear character manifested by NLO absorption, giving rise to optical limiting or saturated absorption associated with excited state absorption and Pauli blocking in different materials. In particular, the saturable absorption of these emerging LD materials including two-dimensional semiconductors as well as colloidal TI nanoparticles has recently been utilized for Q-switching and mode-locking ultra-short pulse generation across the visible, near infrared and middle infrared wavelength regions. Beside the large operation bandwidth, these ultrafast photonics applications are especially benefit from the high recovery rate as well as the facile processibility of these LD materials. The prominent NLO response of these LD materials have also provided new avenues for the development of novel NLO and photonics devices for all-optical control as well as optical circuits beyond ultrafast lasers.

High-repetition-rate all-fiber femtosecond laser with an optical integrated component

We demonstrate a high-repetition-rate all-fiber soliton pulse laser mode-locked by the nonlinear polarization rotation technique. The laser cavity is effectively shortened by incorporating an optical integrated component possessing the hybrid functions of a polarization-dependent isolator, a wavelength-division multiplexer, and an output coupler. Resultant output soliton pulses have a fundamental repetition rate of 384 MHz, a 3-dB spectral bandwidth of 25.2 nm, and a dechirped pulse duration of 115 fs. By using an external power amplification and pulse recompression system, the average output power of the laser is boosted to 207 mW. The amplified pulses have a 2.33-ps duration, which is recompressed to 340 fs. Numerical simulations reproduce the generation of high-repetition-rate soliton pulses in the fiber laser. Such a simple and low-cost high-repetition-rate fiber laser is a potential laser source for various practical applications.

Infrared absorber based on sandwiched two-dimensional black phosphorus metamaterials

As a direct band gap two-dimensional (2D) semiconductor material, black phosphorus (BP) bridges the characteristics of graphene, with a zero or near-zero band gap, and transition metal dichalcogenides, with a wide band gap. In the infrared (IR) regime, 2D BP materials can harvest electromagnetic energy due to losses derived from its surface conductivity. In this paper, we propose an IR absorber design comprising 2D BP metamaterials sandwiched between dielectric layers. The multilayered sandwich-like absorber structure is mounted on a full reflective gold mirror, which forms a Fabry-Perot resonator to strengthen light-matter interactions. Harvested surface plasmons are excited around the 2D BP metamaterial edges, and the incident IR light can be efficiently dissipated by increasing the number of layers of the sandwich-like structure (NLSS). The physical absorption mechanism can be attributed to the destructive interference from the metamaterials, which can be enhanced with increasing NLSS. Here, a phase difference of about 180° is obtained between the directly reflected wave from the first interface and the emergent wave derived from the superposition of the multiple reflections among the resonator, and the amplitude of the emergent wave is steadily reduced to a value close to that of the directly reflected wave with increasing NLSS for incident transverse-magnetic polarized IR illumination.

Nonlinear Black Phosphorus for Ultrafast Optical Switching

The outstanding electronic and optical properties of black phosphorus (BP) in a two-dimensional (2D) but unique single-layer puckered structure have opened intense research interest ranging from fundamental physics to nanoscale applications covering the electronic and optical domains. The direct and controllable electronic bandgap facilitating wide range of tunable optical response coupled with high anisotropic in-plane properties made BP a promising nonlinear optical material for broadband optical applications. Here, we investigate ultrafast optical switching relying on the optical nonlinearity of BP. Wavelength conversion for modulated signals whose frequency reaches up to 20 GHz is realized by four-wave-mixing (FWM) with BP-deposited D-shaped fiber. In the successful demonstration of the FWM based wavelength conversion, performance parameter has been increased up to ~33% after employing BP in the device. It verifies that BP is able to perform efficient optical switching in the evanescent field interaction regime at very high speed. Our results might suggest that BP-based ultra-fast photonics devices could be potentially developed for broadband applications.