Noncovalent sidewall functionalization of single-walled carbon nanotubes for protein immobilization

Electrochemical characteristics of the immobilization of calf thymus DNA molecules on multi-walled carbon nanotubes

Immobilization of DNA on carbon nanotubes plays an important role in the development of new types of miniature DNA biosensors. Electrochemical characteristics of the immobilization of calf thymus DNA molecules on the surfaces of multi-walled carbon nanotubes (MWNTs) have been investigated by cyclic voltammetry and electrochemical impedance analysis. The peak currents for Fe(CN)(6)(3-)/Fe(CN)(6)(4-) redox couple observed in the cyclic voltammograms decrease and the electron-transfer resistance (R(et)) obtained from the Nyquist plots increase due to the immobilization of DNA molecules (dsDNA or ssDNA) on the surfaces of MWNTs. Most of calf thymus DNA are covalently immobilized on MWNTs via diimide-activated amidation between the carboxylic acid groups on the carbon nanotubes and the amino groups on DNA bases, though the direct adsorption of the DNA molecules on MWNTs can be observed. Additionally, the interaction between DNA molecules immobilized on MWNTs and small biomolecules (ethidium bromide) can be observed obviously by cyclic voltammetry and electrochemical impedance analysis. This implies that the DNA molecules immobilized at the surface of MWNTs, with little structure change, still has the ability to interact with small biomolecules.

Functionalized multiwall carbon nanotube/gold nanoparticle composites

Multiwall carbon nanotubes (MWCNTs) were chemically oxidized in a mixture of sulfuric acid and nitric acid (3:1) while being ultrasonicated. The effect of oxidative ultrasonication at room temperature on development of functional groups on the carbon nanotubes was investigated. The dispersability and the carboxylic acid group concentration of functionalized MWCNTs (fMWNTs) varied with reaction time. The concentration of carboxylic acid groups on fMWNTs increased from 4 x 10(-4) mol/g of fMWNTs to 1.1 x 10(-3) mol/g by doubling the treatment period from 4 to 8 h. The colloidal stability of aqueous fMWCNTs dispersions was enhanced through elongated oxidation. fMWCNTs that were reacted longer than 4 h did not precipitate in aqueous media for at least 24 h. The layer-by-layer self-assembly of polyelectrolytes on fMWCNTs was characterized by zeta potential measurements. The zeta potential of fMWCNTs changed from negative charge to positive charge when cationic polyelectrolytes were self-assembled on their surface. With addition of anionic polyelectrolytes, cationic polyelectrolyte coated fMWCNTs showed the expected charge reversal as expected for multilayer self-assembly. Complex formation of positively charged gold nanoparticles and negatively charged fMWCNTs was achieved with and without polyelectrolyte coatings by electrostatic interaction. The complex formation was characterized by high-resolution transmission electron microscopy and energy-dispersive X-ray spectroscopy. The here found complex formation of positively charged colloidal gold and defect sites on fMWNTs indicates the location of functional groups on carbon nanotubes. It is suggested that positively charged colloids such as gold nanoparticles could be used for detection of defect sites on carbon nanotubes.

Biomolecule-directed assembly of nanoscale building blocks studied via lattice Monte Carlo simulation

We perform lattice Monte Carlo simulations to study the self-assembly of functionalized inorganic nanoscale building blocks using recognitive biomolecule linkers. We develop a minimal coarse-grained lattice model for the nanoscale building block (NBB) and the recognitive linkers. Using this model, we explore the influence of the size ratio of linker length to NBB diameter on the assembly process and the structural properties of the resulting aggregates, including the spatial distribution of NBBs and aggregate topology. We find the constant-kernel Smoluchowski theory of diffusion-limited cluster-cluster aggregation describes the aggregation kinetics for certain size ratios.

Debundling and dissolution of single-walled carbon nanotubes in amide solvents

Wet chemical methods involving ultrasound and amide solvents were used to purify and separate large bundles of single-walled carbon nanotubes (SWNTs) into individual nanotubes that could then be transported to silicon or mica substrates. The SWNTs studied were produced by the arc-discharge process. Dry oxidation was used in an initial step to remove amorphous carbon. Subsequently, two acid purification schemes were investigated (HCl- and HNO(3)-reflux) to remove the metal growth catalyst (Ni-Y). Finally, ultrasonic dispersion of isolated tubes into either N,N-dimethylformamide (DMF) or N-methyl-2-pyrrolidone (NMP) was carried out. Raman scattering, atomic force microscopy (AFM), and electron microscopy were used to study the evolution of the products. Raman scattering was used to probe possible wall damage during the chemical processing. We found that both HCl and HNO(3) could be used to successfully remove the Ni-Y below approximately 1 wt %. However, the HNO(3)-reflux produced significant wall damage (that could be reversed by vacuum annealing at 1000 degrees C). In the dispersion step, both amide solvents (DMF and NMP) produced a high degree of isolated tubes in the final product, and no damage during this dispersion step was observed. HNO(3)-refluxed tubes were found to disperse the best into the amide solvents, perhaps because of significant wall functionalization. AFM was used to study the filament diameter and length distributions in the final product, and interesting differences in these distributions were observed, depending on the chemical processing route.

The use of nanocrystals in biological detection

In the coming decade, the ability to sense and detect the state of biological systems and living organisms optically, electrically and magnetically will be radically transformed by developments in materials physics and chemistry. The emerging ability to control the patterns of matter on the nanometer length scale can be expected to lead to entirely new types of biological sensors. These new systems will be capable of sensing at the single-molecule level in living cells, and capable of parallel integration for detection of multiple signals, enabling a diversity of simultaneous experiments, as well as better crosschecks and controls.

Silica nanoparticle size influences the structure and enzymatic activity of adsorbed lysozyme

Adsorption of chicken egg lysozyme on silica nanoparticles of various diameters has been studied. Special attention has been paid to the effect of nanoparticle size on the structure and function of the adsorbed protein molecules. Both adsorption patterns and protein structure and function are strongly dependent on the size of the nanoparticles. Formation of molecular complexes is observed for adsorption onto 4-nm silica. True adsorptive behavior is evident on 20- and 100-nm particles, with the former resulting in monolayer adsorption and the latter yielding multilayer adsorption. A decrease in the solution pH results in a decrease in lysozyme adsorption. A change of protein structure upon adsorption is observed, as characterized by a loss in alpha-helix content, and this is strongly dependent on the size of the nanoparticle and the solution pH. Generally, greater loss of alpha helicity was observed for the lysozyme adsorbed onto larger nanoparticles under otherwise similar conditions. The activity of lysozyme adsorbed onto silica nanoparticles is lower than that of the free protein, and the fraction of activity lost correlates well with the decrease in alpha-helix content. These results indicate that the size of the nanoparticle, perhaps because of the contributions of surface curvature, influences adsorbed protein structure and function.

Adsorption and immobilization of cytochrome c on nanodiamonds

Methods have been developed to immobilize proteins onto the surfaces ofnanodiamonds with an average size of 5 +/- 1 nm. The immobilization started with carboxylation/oxidization of diamonds with strong acids, followed by coating the surfaces with poly-L-lysine (PL) for covalent attachment of proteins using heterobifunctional cross-linkers. The feasibility of this approach is proven with fluorescent labeling of the PL-coated diamonds by Alexa Fluor 488 and subsequent detection of the emission using a confocal fluorescence microscope. Immobilization of proteins onto the surfaces is also demonstrated with yeast cytochrome c, which possesses a free SH group for linkage and a characteristic Soret absorption band for observation.

Design of Polyaromatic Hydrocarbon-Supported Tin Reagents: A New Family of Tin Reagents Easily Removable from Reaction Mixtures

We report in this paper the preparation and use of stannanes 11, 12a, and 12b, compounds whose 3-pyrenylpropyl side chain affinity for activated carbon simplifies tin removal and product isolation. Our pyrene-supported reagents can be used for radical reductions and cyclizations (11), radical and cationic allylations (12a), and Stille couplings (12b) in much the same way as tributyltin derivatives.

Chemically Functionalized Carbon Nanotubes as Substrates for Neuronal Growth

We report the use of chemically modified carbon nanotubes as a substrate for cultured neurons. The morphological features of neurons that directly reflect their potential capability in synaptic transmission are characterized. The chemical properties of carbon nanotubes are systematically varied by attaching different functional groups that confer known characteristics to the substrate. By manipulating the charge carried by functionalized carbon nanotubes we are able to control the outgrowth and branching pattern of neuronal processes.

Single-step in situ synthesis of double bond-grafted yttrium-hydroxide nanotube core-shell structures

Novel MMA-Y(OH)(3) nanotube core-shell structures have been successfully prepared with double bonds successfully grafted on the surface through a single-step in-situ hydrothermal method.

Direct Electrochemistry of Xanthine Oxidase at a Gold Electrode Modified with Single-Wall Carbon Nanotubes

The direct electrochemistry of xanthine oxidase (XOD) was accomplished at a gold electrode modified with single-wall carbon nanotubes (SWNTs). A pair of well-defined redox peaks was obtained for XOD with the reduction peak potential at -0.478 V and a peak potential separation of 28 mV at pH 7.0. Both FT-IR spectra and the dependence of the reduction peak current on the scan rate revealed that XOD adsorbed onto the SWNT surfaces. The redox wave corresponds to the redox center of the flavin adenine dinucleotide (FAD) of the XOD adsorbate. Compared to other types of carbonaceous electrode materials, the electron transfer rate of XOD redox reaction was greatly enhanced at the SWNT-modified electrode. The peak potential was shown to be pH dependent. Spectral methods verified that the attachment of XOD onto SWNTs does not perturb the XOD conformations drastically.

Controlled Functionalization of Multiwalled Carbon Nanotubes by in Situ Atom Transfer Radical Polymerization

The in situ ATRP (atom transfer radical polymerization) "grafting from" approach was successfully applied to graft poly(methyl methacrylate) (PMMA) onto the convex surfaces of multiwalled carbon nanotubes (MWNT). The thickness of the coated polymer layers can be conveniently controlled by the feed ratio of MMA to preliminarily functionalized MWNT (MWNT-Br). The resulting MWNT-based polymer brushes were characterized and confirmed with FTIR, 1H NMR, SEM, TEM, and TGA. Moreover, the approach has been extended to the copolymerization system, affording novel hybrid core-shell nanoobjects with MWNT as the core and amphiphilic poly(methyl methacrylate)-block-poly(hydroxyethyl methacrylate) (PMMA-b-PHEMA) as the shell. The approach presented here may open an avenue for exploring and preparing novel carbon nanotubes-based nanomaterials and molecular devices with tailor-made structure, architecture, and properties.

Electrochemical Biosensing Platforms Using Platinum Nanoparticles and Carbon Nanotubes

Platinum nanoparticles with a diameter of 2-3 nm were prepared and used in combination with single-wall carbon nanotubes (SWCNTs) for fabricating electrochemical sensors with remarkably improved sensitivity toward hydrogen peroxide. Nafion, a perfluorosulfonated polymer, was used to solubilize SWCNTs and also displayed strong interactions with Pt nanoparticles to form a network that connected Pt nanoparticles to the electrode surface. TEM and AFM micrographs illustrated the deposition of Pt nanoparticles on carbon nanotubes whereas cyclic voltammetry confirmed an electrical contact through SWCNTs between Pt nanoparticles and the glassy carbon (GC) or carbon fiber backing. With glucose oxidase (GOx) as an enzyme model, we constructed a GC or carbon fiber microelectrode-based biosensor that responds even more sensitively to glucose than the GC/GOx electrode modified by Pt nanoparticles or CNTs alone. The response time and detection limit (S/N = 3) of this biosensor was determined to be 3 s and 0.5 microM, respectively.

Experimental and Computational Investigations of the Properties of Fluorinated Single-Walled Carbon Nanotubes

Fluorination of single-walled carbon nanotubes by reaction with elemental fluorine at elevated temperatures provides fluorinated single-walled carbon nanotubes (F-SWNT), which have the highest degree of functionalization (up to F/C = 1/2) of any derivatized carbon-nanotube material reported to date. Also, F-SWNTs have received more scrutiny than any other functionalized carbon nanotubes. This Minireview covers experimental and computational investigations of F-SWNTs with a focus on the nature and the strength of the C-F linkage.

Single-Walled Carbon Nanotube Based Molecular Switch Tunnel Junctions

This article describes two-terminal molecular switch tunnel junctions (MSTJs) which incorporate a semiconducting, single-walled carbon nanotube (SWNT) as the bottom electrode. The nanotube interacts noncovalently with a monolayer of bistable, nondegenerate [2]catenane tetracations, self-organized by their supporting amphiphilic dimyristoylphosphatidyl anions which shield the mechanically switchable tetracations from a two-micrometer wide metallic top electrode. The resulting 0.002 micron 2 area tunnel junction addresses a nanometer wide row of approximately 2000 molecules. Active and remnant current-voltage measurements demonstrated that these devices can be reconfigurably switched and repeatedly cycled between high and low current states under ambient conditions. Control compounds, including a degenerate [2]catenane, were explored in support of the mechanical origin of the switching signature. These SWNT-based MSTJs operate like previously reported silicon-based MSTJs, but differently from similar devices incorporating bottom metal electrodes. The relevance of these results with respect to the choice of electrode materials for molecular electronics devices is discussed.

A novel multi-walled carbon nanotube-based biosensor for glucose detection

The bioelectrochemical characteristics of a novel multi-walled carbon nanotube (MWNT)-based biosensor for glucose detection are studied and compared with those of glassy carbon (GC)-based biosensor. The MWNT-based biosensor exhibits a strong glucose response at applied potentials of 0.65 and 0.45 V versus Ag/AgCl, respectively, while GC-based biosensor shows a weak glucose response at 0.65 V and no response at 0.45 V. Besides, the MWNT-based biosensor shows a high stability of 86.7% of the initial activity to glucose after four-month storage, much higher than 37.2%, the corresponding value for a GC-based biosensor. The detection mechanism of the MWNT-based biosensor is also discussed in detail.

A theoretical exploration of the 1,3-dipolar cycloadditions onto the sidewalls of (n,n) armchair single-wall carbon nanotubes

The viability of 1,3-dipolar cycloadditions of a series of 1,3-dipolar molecules (azomethine ylide, ozone, nitrone, nitrile imine, nitrile ylide, nitrile oxide, diazomethane, and methyl azide) onto the sidewalls of carbon nanotubes has been assessed theoretically by means of a two-layered ONIOM approach. The theoretical calculations predict the following: (i) other than the 18-valence-electron azomethine ylide and ozone, the 16-valence-electron nitrile ylide and nitrile imine are the best candidates for experimentalists to try; (ii) upon 1,3-dipolar cycloaddition, a 1,3-diople molecule is di-sigma-bonded to a pair of carbon atoms on the sidewall of SWNT, forming a five-membered ring surface species; (iii) the as-formed 1,3-dipole-SWNT bonding is much weaker than that in the products of the molecular 1,3-DC reactions and can be plausibly broken by heating at elevated temperatures; (iv) the sidewalls of the armchair (n,n) SWNTs (n = 5-10) are subject to the 1,3-DCs of ozone and azomethine ylides; (v) both the 1,3-DC reactivity and retro-1,3-DC reactivity are moderately dependent on the diameters of SWNTs, implying the feasibility of making use of the heterogeneous 1,3-DC chemistry to purify and separate SWNTs diameter-specifically.

In situ quantum dot growth on multiwalled carbon nanotubes

The generation of nanoscale interconnects and supramolecular, hierarchical assemblies enables the development of a number of novel nanoscale applications. A rational approach toward engineering a robust system is through chemical recognition. Here, we show the in situ mineralization of crystalline CdTe quantum dots on the surfaces of oxidized multiwalled carbon nanotubes (MWNTs). We coordinate metallic precursors of quantum dots directly onto nanotubes and then proceed with in situ growth. The resulting network of molecular-scale "fused" nanotube-nanocrystal heterojunctions demonstrates a controlled synthetic route to the synthesis of complex nanoscale heterostructures. Extensive characterization of these heterostructures has been performed using scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), energy-dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, UV-visible spectroscopy, and X-ray diffraction (XRD).

Nanotechnology and medicine

Nanotechnology, or systems/device manufacture at the molecular level, is a multidisciplinary scientific field undergoing explosive development. The genesis of nanotechnology can be traced to the promise of revolutionary advances across medicine, communications, genomics and robotics. On the surface, miniaturisation provides cost effective and more rapidly functioning mechanical, chemical and biological components. Less obvious though is the fact that nanometre sized objects also possess remarkable self-ordering and assembly behaviours under the control of forces quite different from macro objects. These unique behaviours are what make nanotechnology possible, and by increasing our understanding of these processes, new approaches to enhancing the quality of human life will surely be developed. A complete list of the potential applications of nanotechnology is too vast and diverse to discuss in detail, but without doubt one of the greatest values of nanotechnology will be in the development of new and effective medical treatments (i.e., nanomedicine). This review focuses on the potential of nanotechnology in medicine, including the development of nanoparticles for diagnostic and screening purposes, artificial receptors, DNA sequencing using nanopores, manufacture of unique drug delivery systems, gene therapy applications and the enablement of tissue engineering.

Molecular ordering of organic molten salts triggered by single-walled carbon nanotubes

When mixed with imidazolium ion-based room-temperature ionic liquid, pristine single-walled carbon nanotubes formed gels after being ground. The heavily entangled nanotube bundles were found to untangle within the gel to form much finer bundles. Phase transition and rheological properties suggest that the gels are formed by physical cross-linking of the nanotube bundles, mediated by local molecular ordering of the ionic liquids rather than by entanglement of the nanotubes. The gels were thermally stable and did not shrivel, even under reduced pressure resulting from the nonvolatility of the ionic liquids, but they would readily undergo a gel-to-solid transition on absorbent materials. The use of a polymerizable ionic liquid as the gelling medium allows for the fabrication of a highly electroconductive polymer/nanotube composite material, which showed a substantial enhancement in dynamic hardness.

Micelle-encapsulated carbon nanotubes: a route to nanotube composites

We report a general approach toward dispersing single-walled carbon nanotubes (SWNTs) in solvents and polymer materials, by encapsulating SWNTs within cross-linked micelles. Micelles made from polystyrene-block-poly(acrylic acid) (PS-b-PAA), an amphiphilic block copolymer, are first assembled around SWNTs by gradually adding H2O to a suspension of nanotubes in dimethylformamide. The hydrophilic, outer shells of these micelles are then chemically cross-linked with a difunctional linker molecule. Pure encapsulated SWNTs (e-SWNTs) can then be separated from empty cross-linked micelles by consecutive cycles of centrifugation and redispersion. Atomic force and transmission electron microscopies of the resulting nanostructures demonstrate that individual nanotubes (rather than bundles) have been completely encased in polymer shells whose thickness is slightly larger than that of empty micelles. e-SWNTs encapsulated in PS-b-PAA can be permanently redispersed in H2O, in organic solvents, and in both hydrophobic and hydrophilic polymer matrices with minimal sonication. Micelle encapsulation could improve the compositing of SWNTs in a wide variety of polymer materials for structural, electronic, and thermal applications.

Noncovalent functionalization of carbon nanotubes for highly specific electronic biosensors

Novel nanomaterials for bioassay applications represent a rapidly progressing field of nanotechnology and nanobiotechnology. Here, we present an exploration of single-walled carbon nanotubes as a platform for investigating surface-protein and protein-protein binding and developing highly specific electronic biomolecule detectors. Nonspecific binding on nanotubes, a phenomenon found with a wide range of proteins, is overcome by immobilization of polyethylene oxide chains. A general approach is then advanced to enable the selective recognition and binding of target proteins by conjugation of their specific receptors to polyethylene oxide-functionalized nanotubes. This scheme, combined with the sensitivity of nanotube electronic devices, enables highly specific electronic sensors for detecting clinically important biomolecules such as antibodies associated with human autoimmune diseases.

Solubilization of single-wall carbon nanotubes by supramolecular encapsulation of helical amylose

We have developed a simple, efficient process for solubilization of single-wall carbon nanotubes (SWNTs) with amylose in aqueous DMSO. This process requires two important conditions, presonication of SWNTs and subsequent amylose treatment in an optimum mixture of DMSO/H2O. The former step separates SWNT bundles, and the latter step provides a maximum cooperative interaction of SWNTs with amylose, leading to the immediate and complete solubilization. The best solvent condition for this is around 10-20% DMSO, in which amylose assumes a random conformation or an interrupted helix. This indicates that the amylose helix is not the prerequisite for encapsulation of SWNTs. The SEM and AFM images of the encapsulated SWNTs manifest loosely twisted ribbons wrapping around SWNTs, which are locally intertwined as a multiple twist, but no clumps of the host amylose are seen on SWNT capsules.

Peptides with selective affinity for carbon nanotubes

Because of their extraordinary electronic and mechanical properties, carbon nanotubes have great potential as materials for applications ranging from molecular electronics to ultrasensitive biosensors. Biological molecules interacting with carbon nanotubes provide them with specific chemical handles that would make several of these applications possible. Here we use phage display to identify peptides with selective affinity for carbon nanotubes. Binding specificity has been confirmed by demonstrating direct attachment of nanotubes to phage and free peptides immobilized on microspheres. Consensus binding sequences show a motif rich in histidine and tryptophan, at specific locations. Our analysis of peptide conformations shows that the binding sequence is flexible and folds into a structure matching the geometry of carbon nanotubes. The hydrophobic structure of the peptide chains suggests that they act as symmetric detergents.

Carbon nanotube-enhanced electrochemical DNA biosensor for DNA hybridization detection

A novel and sensitive electrochemical DNA biosensor based on multi-walled carbon nanotubes functionalized with a carboxylic acid group (MWNTs-COOH) for covalent DNA immobilization and enhanced hybridization detection is described. The MWNTs-COOH-modified glassy carbon electrode (GCE) was fabricated and oligonucleotides with the 5'-amino group were covalently bonded to the carboxyl group of carbon nanotubes. The hybridization reaction on the electrode was monitored by differential pulse voltammetry (DPV) analysis using an electroactive intercalator daunomycin as an indicator. Compared with previous DNA sensors with oligonucleotides directly incorporated on carbon electrodes, this carbon nanotube-based assay with its large surface area and good charge-transport characteristics dramatically increased DNA attachment quantity and complementary DNA detection sensitivity. This is the first application of carbon nanotubes to the fabrication of an electrochemical DNA biosensor with a favorable performance for the rapid detection of specific hybridization.

Noncovalent functionalization of multi-walled carbon nanotubes by pyrene containing polymers

Multi-walled carbon nanotubes (MWNTs) have been solubilized in water and in various organic solvents by noncovalent side-wall functionalization by pyrene containing polymers.

The emerging field of nanotube biotechnology

Nanoparticles are being developed for a host of biomedical and biotechnological applications, including drug delivery, enzyme immobilization and DNA transfection. Spherical nanoparticles are typically used for such applications, which reflects the fact that spheres are easier to make than other shapes. Micro- and nanotubes--structures that resemble tiny drinking straws--are alternatives that might offer advantages over spherical nanoparticles for some applications. This article discusses four approaches for making micro- and nanotubes, and reviews the current status of efforts to develop biomedical and biotechnological applications of these tubular structures.

Organic functionalization of the sidewalls of carbon nanotubes by diels-alder reactions: a theoretical prediction

[structure: see text] The viability of the Diels-Alder (DA) cycloaddition of conjugated dienes onto the sidewalls of single-wall carbon nanotubes is assessed by means of a two-layered ONIOM(B3LYP/6-31G:AM1) approach. Whereas the DA reaction of 1,3-butadiene on the sidewall of an armchair (5,5) nanotube is found to be unfavorable, the cycloaddition of quinodimethane is predicted to be viable due to the aromaticity stabilization at the corresponding transition states and products.