Electrochemical Biosensing Platforms Using Platinum Nanoparticles and Carbon Nanotubes

Electrochemical Synthesis of Polypyrrole, Reduced Graphene Oxide, and Gold Nanoparticles Composite and Its Application to Hydrogen Peroxide Biosensor

Here we report a facile eco-friendly one-step electrochemical approach for the fabrication of a polypyrrole (PPy), reduced graphene oxide (RGO), and gold nanoparticles (nanoAu) biocomposite on a glassy carbon electrode (GCE). The electrochemical behaviors of PPy–RGO–nanoAu and its application to electrochemical detection of hydrogen peroxide were investigated by cyclic voltammetry. Graphene oxide and pyrrole monomer were first mixed and casted on the surface of a cleaned GCE. After an electrochemical processing consisting of the electrooxidation of pyrrole monomer and simultaneous electroreduction of graphene oxide and auric ions (Au³⁺) in aqueous solution, a PPy–RGO–nanoAu biocomposite was synthesized on GCE. Each component of PPy–RGO–nanoAu is electroactive without non-electroactive substance. The obtained PPy–RGO–nanoAu/GCE exhibited high electrocatalytic activity toward hydrogen peroxide, which allows the detection of hydrogen peroxide at a negative potential of about −0.62 V vs. SCE. The amperometric responses of the biosensor displayed a sensitivity of 40 µA/mM, a linear range of 32 µM–2 mM, and a detection limit of 2.7 µM (signal-to-noise ratio = 3) with good stability and acceptable reproducibility and selectivity. The results clearly demonstrate the potential of the as-prepared PPy–RGO–nanoAu biocomposite for use as a highly electroactive matrix for an amperometric biosensor.

3D nanostructured inkjet printed graphene via UV-pulsed laser irradiation enables paper-based electronics and electrochemical devices

Emerging research on printed and flexible graphene-based electronics is beginning to show tremendous promise for a wide variety of fields including wearable sensors and thin film transistors. However, post-print annealing/reduction processes that are necessary to increase the electrical conductivity of the printed graphene degrade sensitive substrates (e.g., paper) and are whole substrate processes that are unable to selectively anneal/reduce only the printed graphene-leaving sensitive device components exposed to damaging heat or chemicals. Herein a pulsed laser process is introduced that can selectively irradiate inkjet printed reduced graphene oxide (RGO) and subsequently improve the electrical conductivity (Rsheet∼0.7 kΩ□(-1)) of printed graphene above previously published reports. Furthermore, the laser process is capable of developing 3D petal-like graphene nanostructures from 2D planar printed graphene. These visible morphological changes display favorable electrochemical sensing characteristics-ferricyanide cyclic voltammetry with a redox peak separation (ΔEp) ≈ 0.7 V as well as hydrogen peroxide (H2O2) amperometry with a sensitivity of 3.32 μA mM(-1) and a response time of <5 s. Thus this work paves the way for not only paper-based electronics with graphene circuits, it enables the creation of low-cost and disposable graphene-based electrochemical electrodes for myriad applications including sensors, biosensors, fuel cells, and theranostic devices.

Microwave-assisted synthesis of NaA nanozeolite from slag and performance of Ag-doped nanozeolite as an efficient material for determination of hydrogen peroxide

A new amperometric sensor is prepared based on a Ag doped NaA nanozeolite modified carbon paste electrode (Ag/ACPE) in order to detect hydrogen peroxide (H₂O₂) in phosphate buffer solution (PBS, pH 7.0).

One-pot, efficient and green synthesis of acridinedione derivatives using highly monodisperse platinum nanoparticles supported with reduced graphene oxide

An efficient, high yielding, quick method has been developed for the synthesis of acridinedione derivatives using highly monodisperse Pt NPs@rGO.

Role of interfacial interactions to control the extent of wrapping of polymer chains on multi-walled carbon nanotubes

Transmission electron microscopic image of separated MWCNTs (N51L15G5) showing the wrapped polymer chains on the MWCNTs surface, which corresponds to the α-phase of the PP.

pulSED: pulsed sonoelectrodeposition of fractal nanoplatinum for enhancing amperometric biosensor performance

A technique for deposition of fractal nanometal as a transducer in electrochemical sensing is described. The effect(s) of duty cycle and deposition time were explored, and two sensors are demonstrated.

Materiomics for Oral Disease Diagnostics and Personal Health Monitoring: Designer Biomaterials for the Next Generation Biomarkers

We live in exciting times for a new generation of biomarkers being enabled by advances in the design and use of biomaterials for medical and clinical applications, from nano- to macro-materials, and protein to tissue. Key challenges arise, however, due to both scientific complexity and compatibility of the interface of biology and engineered materials. The linking of mechanisms across scales by using a materials science approach to provide structure-process-property relations characterizes the emerging field of 'materiomics,' which offers enormous promise to provide the hitherto missing tools for biomaterial development for clinical diagnostics and the next generation biomarker applications towards personal health monitoring. Put in other words, the emerging field of materiomics represents an essentially systematic approach to the investigation of biological material systems, integrating natural functions and processes with traditional materials science perspectives. Here we outline how materiomics provides a game-changing technology platform for disruptive innovation in biomaterial science to enable the design of tailored and functional biomaterials--particularly, the design and screening of DNA aptamers for targeting biomarkers related to oral diseases and oral health monitoring. Rigorous and complementary computational modeling and experimental techniques will provide an efficient means to develop new clinical technologies in silico, greatly accelerating the translation of materiomics-driven oral health diagnostics from concept to practice in the clinic.

A Facile One-Pot Synthesis of Au/Cu2O Nanocomposites for Nonenzymatic Detection of Hydrogen Peroxide

Au/Cu2O nanocomposites were successfully synthesized by a facile one-pot redox reaction without additional reducing agent under room temperature. The morphologies and structures of the as-prepared products were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). The electrocatalytic performance of Au/Cu2O nanocomposites towards hydrogen peroxide was evaluated by cyclic voltammetry (CV) and chronoamperometry (CA). The prepared Au/Cu2O nanocomposite electrode showed a wide linear range from 25 to 11.2 mM (R = 0.9989) with a low detection limit of 1.05 μM (S/N = 3) and high sensitivity of 292.89 mA mM(-1) cm(-2). The enhanced performance for H2O2 detection can be attributed to the introduction of Au and the synergistic effect between Au and Cu2O. It is demonstrated that the Au/Cu2O nanocomposites material could be a promising candidate for H2O2 detection.

Amperometric flow injection analysis of glucose using immobilized glucose oxidase on nano-composite carbon nanotubes-platinum nanoparticles carbon paste electrode

We report a novel amperometric glucose biosensor based on glucose oxidase (GOx) immobilized on a carbon nanotube (CNTs)-poly(diallyldimethyl-ammonium chloride) (PDDA)-platinum nanoparticle (PtNPs) modified carbon-paste electrode (CNTs-PDDA-PtNPs/CPE). The CNTs-PDDA-PtNPs composite materials were characterized by TEM and electrochemical techniques. Cyclic voltammetric results reveal direct electron transfer of the immobilized GOx, indicated by two quasi-reversible redox peaks at a potential of 0.37V (vs. Ag/AgCl) in phosphate buffered solution (PBS) (0.10M, pH 7). The biosensor provides good glucose oxidation activity and retention of GOx electrocatalytic activity due to CNTs-PDDA-PtNPs enhancement of the redox response. The carbon paste electrode was installed as working electrode in a flow through electrochemical cell of a flow injection (FI) system. Glucose was quantified using amperometric measurements at 0.5V vs. Ag/AgCl and PBS carrier (0.10M, pH 7.0) at a flow rate of 1.0mLmin^-1. The linear working ranges for glucose measurements were 0.1-3mM (r²=0.995) and 5-100mM (r²=0.997), with corresponding sensitivities of 0.127 and 0.060 (μAs) mM^-1, respectively. The system provides good precision of 2.8% R.S.D with a calculated detection limit (3S/N) of 15μM. The proposed method was successfully applied to determination of glucose in food and pharmaceutical samples with throughput of 200 samplesh^-1.

Cobalt ferrite nanoparticles decorated on exfoliated graphene oxide, application for amperometric determination of NADH and H2O2

Here, cobalt ferrite nanohybrid decorated on exfoliated graphene oxide (CoFe2O4/EGO) was synthesized. The nanohybrid was characterized by different methods such as X-ray diffraction spectroscopy, scanning electron microscopy, energy dispersive X-ray diffraction microanalysis, transmission electron microscopy, FT-IR, Raman spectroscopy and electrochemical methods. The CoFe2O4/EGO nanohybrid was used to modify glassy carbon electrode (GCE). The voltammetric investigations showed that CoFe2O4/EGO nanohybrid has synergetic effect towards the electro-reduction of H2O2 and electro-oxidation of nicotinamide adenine dinucleotide (NADH). Rotating disk chronoamperometry was used for their quantitative analysis. The calibration curves were observed in the range of 0.50 to 100.0 μmol L(-1) NADH and 0.9 to 900.0 μmol L(-1) H2O2 with detections limit of 0.38 and 0.54 μmol L(-1), respectively. The repeatability, reproducibility and selectivity of the electrochemical sensor for analysis of the analytes were studied. The new electrochemical sensor was successfully applied for the determination of NADH and H2O2 in real samples with satisfactory results.

Green Synthesis of Metallic Nanoparticles via Biological Entities

Nanotechnology is the creation, manipulation and use of materials at the nanometre size scale (1 to 100 nm). At this size scale there are significant differences in many material properties that are normally not seen in the same materials at larger scales. Although nanoscale materials can be produced using a variety of traditional physical and chemical processes, it is now possible to biologically synthesize materials via environment-friendly green chemistry based techniques. In recent years, the convergence between nanotechnology and biology has created the new field of nanobiotechnology that incorporates the use of biological entities such as actinomycetes algae, bacteria, fungi, viruses, yeasts, and plants in a number of biochemical and biophysical processes. The biological synthesis via nanobiotechnology processes have a significant potential to boost nanoparticles production without the use of harsh, toxic, and expensive chemicals commonly used in conventional physical and chemical processes. The aim of this review is to provide an overview of recent trends in synthesizing nanoparticles via biological entities and their potential applications.

Highly sensitive and rapid detection of acetylcholine using an ITO plate modified with platinum-graphene nanoparticles

Determining the concentrations of acetylcholine (ACh) and choline (Ch) is clinically important. ACh is a neurotransmitter that acts as a key link in the communication between neurons in the spinal cord and in nerve skeletal junctions in vertebrates, and plays an important role in transmitting signals in the brain. A bienzymatic sensor for the detection of ACh was prepared by co-immobilizing choline oxidase (ChO) and acetylcholinesterase (AChE) on graphene matrix/platinum nanoparticles, and then electrodepositing them on an ITO-coated glass plate. Graphene nanoparticles were decorated with platinum nanoparticles and were electrodeposited on a modified ITO-coated glass plate to form a modified electrode. The modified electrode was characterized by scanning electron microscopy (SEM), cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) studies. The optimum response of the enzyme electrode was obtained at pH 7.0 and 35 °C. The response time of this ACh-sensing system was shown to be 4 s. The linear range of responses to ACh was 0.005-700 μM. This biosensor exhibits excellent anti-interferential abilities and good stability, retaining 50% of its original current even after 4 months. It has been applied for the detection of ACh levels in human serum samples.

Voltammetric studies of Azathioprine on the surface of graphite electrode modified with graphene nanosheets decorated with Ag nanoparticles

By using graphene nanosheets decorated with Ag nanoparticles (AgNPs-G) as an effective approach for the surface modification of pyrolytic graphite electrode (PGE), a sensing platform was fabricated for the sensitive voltammetric determination of Azathioprine (Aza). The prepared AgNPs-G nanosheets were characterized using transmission electron microscopy (TEM), X-ray diffraction (XRD), UV-vis and Raman spectroscopy techniques. The electrochemical behavior of Aza was investigated by means of cyclic voltammetry. Comparing to the bare PGE, a remarkable enhancement was observed in the response characteristics of Aza on the surface of the modified electrode (AgNPs-G/PGE) as well as a noticeable decrease in its reduction overpotential. These results can be attributed to the incredible enlargement in the microscopic surface area of the electrode due to the presence of graphene nanosheets together with strong adsorption of Aza on its surface. The effect of experimental parameters such as accumulation time, the amount of modifier suspension and pH of the supporting electrolyte were also optimized toward obtaining the maximum sensitivity. Under the optimum conditions, the calibration curve studies demonstrated that the peak current increased linearly with Aza concentrations in the range of 7 × 10(-7) to 1 × 10(-4)mol L(-1) with the detection limit of 68 nM. Further experiments revealed that the modified electrode can be successfully applied for the accurate determination of Aza in pharmaceutical preparations.

Carbon Nanomaterials Based Electrochemical Sensors/Biosensors for the Sensitive Detection of Pharmaceutical and Biological Compounds

Electrochemical sensors and biosensors have attracted considerable attention for the sensitive detection of a variety of biological and pharmaceutical compounds. Since the discovery of carbon-based nanomaterials, including carbon nanotubes, C₆₀ and graphene, they have garnered tremendous interest for their potential in the design of high-performance electrochemical sensor platforms due to their exceptional thermal, mechanical, electronic, and catalytic properties. Carbon nanomaterial-based electrochemical sensors have been employed for the detection of various analytes with rapid electron transfer kinetics. This feature article focuses on the recent design and use of carbon nanomaterials, primarily single-walled carbon nanotubes (SWCNTs), reduced graphene oxide (rGO), SWCNTs-rGO, Au nanoparticle-rGO nanocomposites, and buckypaper as sensing materials for the electrochemical detection of some representative biological and pharmaceutical compounds such as methylglyoxal, acetaminophen, valacyclovir, β-nicotinamide adenine dinucleotide hydrate (NADH), and glucose. Furthermore, the electrochemical performance of SWCNTs, rGO, and SWCNT-rGO for the detection of acetaminophen and valacyclovir was comparatively studied, revealing that SWCNT-rGO nanocomposites possess excellent electrocatalytic activity in comparison to individual SWCNT and rGO platforms. The sensitive, reliable and rapid analysis of critical disease biomarkers and globally emerging pharmaceutical compounds at carbon nanomaterials based electrochemical sensor platforms may enable an extensive range of applications in preemptive medical diagnostics.

Effects of Nanowire Length and Surface Roughness on the Electrochemical Sensor Properties of Nafion-Free, Vertically Aligned Pt Nanowire Array Electrodes

In this paper, vertically aligned Pt nanowire arrays (PtNWA) with different lengths and surface roughnesses were fabricated and their electrochemical performance toward hydrogen peroxide (H₂O₂) detection was studied. The nanowire arrays were synthesized by electroplating Pt in nanopores of anodic aluminum oxide (AAO) template. Different parameters, such as current density and deposition time, were precisely controlled to synthesize nanowires with different surface roughnesses and various lengths from 3 μm to 12 μm. The PtNWA electrodes showed better performance than the conventional electrodes modified by Pt nanowires randomly dispersed on the electrode surface. The results indicate that both the length and surface roughness can affect the sensing performance of vertically aligned Pt nanowire array electrodes. Generally, longer nanowires with rougher surfaces showed better electrochemical sensing performance. The 12 μm rough surface PtNWA presented the largest sensitivity (654 μA·mM⁻¹·cm⁻²) among all the nanowires studied, and showed a limit of detection of 2.4 μM. The 12 μm rough surface PtNWA electrode also showed good anti-interference property from chemicals that are typically present in the biological samples such as ascorbic, uric acid, citric acid, and glucose. The sensing performance in real samples (river water) was tested and good recovery was observed. These Nafion-free, vertically aligned Pt nanowires with surface roughness control show great promise as versatile electrochemical sensors and biosensors.

Hyper-Branched Cu@Cu2O Coaxial Nanowires Mesh Electrode for Ultra-Sensitive Glucose Detection

Electrode design in nanoscale is expected to contribute significantly in constructing an enhanced electrochemical platform for a superb sensor. In this work, we present a facile synthesis of new fashioned heteronanostructure that is composed of one-dimensional Cu nanowires (NWs) and epitaxially grown two-dimensional Cu2O nanosheets (NSs). This hierarchical architecture is quite attractive in molecules detection for three unique characteristics: (1) the three-dimensional hierarchical architecture provides large specific surface areas for more active catalytic sites and easy accessibility for the target molecules; (2) the high-quality heterojunction with minimal lattice mismatch between the built-in current collector (Cu core) and active medium (Cu2O shell) considerably promotes the electron transport; (3) the adequate free space between branches and anisotropic NWs can accommodate a large volume change to avoid collapse or distortion during the reduplicative operation processes under applied potentials. The above three proposed advantages have been addressed in the fabricated Cu@Cu2O NS-NW-based superb glucose sensors, where a successful integration of ultrahigh sensitivity (1420 μA mM(-1) cm(-2)), low limit of detection (40 nM), and fast response (within 0.1 s) has been realized. Furthermore, the durability and reproducibility of such devices made by branched core-shell nanowires were investigated to prove viability of the proposed structures. This achievement in current work demonstrates an innovative strategy for nanoscale electrode design and application in molecular detection.

Pulse Laser Deposition Fabricating Gold Nanoclusters on a Glassy Carbon Surface for Nonenzymatic Glucose Sensing

A One-step technique for depositing gold nanoclusters (GNCs) onto the surface of a glassy carbon (GC) plate was developed by using pulse laser deposition (PLD) with appropriate process parameters. The method is simple and clean without using any templates, surfactants, or stabilizers. The experimental factors (pulse laser number and the pressure of inert gas (Ar)) that affect the morphology and structure of GNCs, and thus affect the electrocatalytic oxidation performance towards glucose were systematically investigated by means of transmission electron microscopy (TEM) and electrochemical methods (cyclic voltammograms (CV) and chronoamperometry methods). The GC electrode modified by GNCs exhibited a rapid response time (about 2 s), a broad linear range (0.1 to 20 mM), and good stability. The sensitivity was estimated to be 31.18 μA cm(-2) mM(-1) (vs. geometric area), which is higher than that of the Au bulk electrode. It has a good resistance to the common interfering species, such as ascorbic acid (AA), uric acid (UA) and 4-acetaminophen (AP). Therefore, this work has demonstrated a simple and effective sensing platform for the nonenzymatic detection of glucose, and can be used as a new material for a novel non-enzymatic glucose sensor.

Self-interconnecting Pt nanowire network electrode for electrochemical amperometric biosensor

One-dimensional Pt nanostructures are of considerable interest for the development of highly stable and sensitive electrochemical sensors. This paper describes a self-interconnecting Pt nanowire network electrode (PtNNE) for the detection of hydrogen peroxide (H2O2) and glucose with ultrahigh sensitivity and stability. The as-prepared PtNNE consists of polycrystalline nanowires with high-index facets along the side surface which provides more active surface atoms on kinks and steps, those ultralong nanowires being interconnected with each other to form a free-standing network membrane. The excellent structural features of the PtNNE promoted its performance as a Pt-based electrochemical sensor both in terms of electrocatalytic activity and stability. Amperometric measurements towards hydrogen peroxide were performed; the PtNNE sensor showed an extremely high sensitivity of 1360 μA mM(-1) cm(-2). This excellent sensitivity is mainly attributed to the high-index facets of the nanowires resulting in their superior electrocatalytic activity towards H2O2, and the interconnected nanowire network forming an "electron freeway" transport model, which could provide multiple electron pathways and fast electron transport on the electrode, leading to rapid reaction and sensitive signal detection. The as-prepared PtNNE also holds promise as an oxidase-based biosensor. As a proof of concept, a PtNNE-based glucose biosensor also showed an outstanding sensitivity as high as 114 μA mM(-1) cm(-2), a low detection limit of 1.5 μM, and an impressive detection range from 5 μM to 30 mM.

Cost-effective flow injection amperometric system with metal nanoparticle loaded carbon nanotube modified screen printed carbon electrode for sensitive determination of hydrogen peroxide

Various metal nanoparticles (NPs) decorated on carbon nanotube (CNT) was modified on the home-made screen printed carbon electrode (SPCE) in order to enhances sensitivity of hydrogen peroxide (H2O2) determination. The simple casting method was used for the electrode modification. The monometallic and bimetallic NPs modified electrodes were investigated for their electrochemical properties for H2O2 reduction. The Pd-CNT/SPCE is appropriated to measure the H2O2 reduction at a potential of -0.3 V, then this modified electrode was incorporated with a home-made flow through cell and applied in a simple flow injection amperometry (FI-Amp). Some parameters influencing the resulted modified electrode and the FI-Amp system were studied. The proposed detection system was able to detect H2O2 in the range of 0.1-1.0 mM, with detection limit of 20 µM. Relative standard deviation for 100 replicated injections of 0.6 mM H2O2 was 2.3%. The reproducibility of 6 electrodes preparing in 3 different lots was 8.2%. It was demonstrated for determination of H2O2 in disinfectant, hair colorant and milk samples. Recoveries in the range of 90-109% were observed. The developed system provided high stability, good repeatability, high sample throughput and low reagent consumption.

Biosensing with Förster Resonance Energy Transfer Coupling between Fluorophores and Nanocarbon Allotropes

Nanocarbon allotropes (NCAs), including zero-dimensional carbon dots (CDs), one-dimensional carbon nanotubes (CNTs) and two-dimensional graphene, exhibit exceptional material properties, such as unique electrical/thermal conductivity, biocompatibility and high quenching efficiency, that make them well suited for both electrical/electrochemical and optical sensors/biosensors alike. In particular, these material properties have been exploited to significantly enhance the transduction of biorecognition events in fluorescence-based biosensing involving Förster resonant energy transfer (FRET). This review analyzes current advances in sensors and biosensors that utilize graphene, CNTs or CDs as the platform in optical sensors and biosensors. Widely utilized synthesis/fabrication techniques, intrinsic material properties and current research examples of such nanocarbon, FRET-based sensors/biosensors are illustrated. The future outlook and challenges for the research field are also detailed.

Highly fluorescent C-dots obtained by pyrolysis of quaternary ammonium ions trapped in all-silica ITQ-29 zeolite

C-dots obtained in the homogeneous phase may exhibit a broad particle size distribution. The formation of C-dots within nanometric reaction cavities could be a methodology to gain control on their size distribution. Among the various possibilities, in the present work, the cavities of small pore size zeolites have been used to confine C-dots generated by the pyrolysis of the organic structure directing agent present in the synthesis of these crystalline aluminosilicates. To explore this methodology, ITQ-29 zeolite having a Linde type A (LTA) structure was prepared as pure silica with 4-methyl-2,3,6,7-tetrahydro-1H,5H-pyrido[3.2.1-ij]quinolinium as the organic structure directing agent. Pyrolysis under an inert atmosphere at 550 °C of a pure-silica ITQ-29 sample (cubic particles of 4 μm edge) renders a highly fluorescent zeolite containing about 15 wt% of the carbonised residue. While another small pore zeolite, ITQ-12 (ITW), also renders photoluminescent C-dots under similar conditions, medium or large pore zeolites, such as silicalite (MFI) or pure silica Beta (BEA), failed to produce fluorescent powders under analogous thermal treatment and only decomposition and complete removal of the corresponding quaternary ammonium ion templates was observed for these zeolites. The dissolution of the pyrolysed ITQ-29 zeolite framework and the extraction of the carbon residue with ethyl acetate have allowed the characterisation of C-dots with particle sizes between 5 and 12 nm and a photoluminescence quantum yield of 0.4 upon excitation at 350 nm that is among the highest reported for non-surface functionalized C-dots. Photoluminescence varies with the excitation wavelength and is quenched by oxygen. Pyrolysed ITQ-29 powders can act as fluorescent oxygen sensors.

Nanoporous CuO layer modified Cu electrode for high performance enzymatic and non-enzymatic glucose sensing

Nanoporous CuO layer on Cu foil with a thick Cu2O interlayer is synthesized via post annealing of previously fabricated Cu(OH)2 nanowires at 500 °C under an oxygen flow. The formation of the thick sandwiched Cu2O layer is realized through the outward diffusion of Cu ions and subsequent oxidation. An O2 pressure above the dissociation pressure of CuO is used to form a CuO layer at the outer surface of the structure, thus realizing a low cost structure having a porous and high isoelectric point layer. The Cu/Cu2O/CuO structure is used as an efficient electrode for glucose sensing. Sensitivities of [Formula: see text] at 0.8 V versus Ag/AgCl and 1066 μA mM(-1) cm(-2) at 0.6 V versus Ag/AgCl are achieved in an enzymatic and non-enzymatic glucose sensing schemes, respectively. The improved electrochemical sensing ability might be attributed to the efficient electrocatalytic reaction on the high crystal quality CuO layer and the porous structure.

Pt NPs@GO as a highly efficient and reusable catalyst for one-pot synthesis of acridinedione derivatives

Pt NPs@GO has been used for the first time for synthesizing acridinedione from dimedone, aromatic aldehydes and various amines as a catalyst.

A green approach for assembling graphene films on different carbon-based substrates and their electrocatalysis toward nitrite

A green strategy for assembling graphene films on various carbon-based substrates and its significant electrocatalytic activity toward nitrite oxidation.

Hierarchical assembly of enzyme-inorganic composite materials with extremely high enzyme activity

We synthesized a composite material with a hierarchical flower-like structure and extremely high enzyme activity and found that the main factor affecting its catalytic activity was the material structure and not the actual enzyme weight percentage.