Environmental applications of carbon-based nanomaterials

The Role of Carbon Nanotube Pretreatments in the Adsorption of Benzoic Acid

Four different types of multi-walled carbon nanotubes (MWCNTs) were used and compared for the treatment of benzoic acid contaminated water. The types of nanotubes used were: (1) non-purified (CNTs^UP), as made; (2) purified (CNTs^P), not containing the catalyst; (3) oxidized (CNTs^OX), characterized by the presence of groups such as, –COOH; (4) calcined (CNTs⁹⁰⁰), with elimination of interactions between nanotubes. In addition, activated carbon was also used to allow for later comparison. The adsorption tests were conducted on an aqueous solution of benzoic acid at concentration of 20 mg/L, as a model of carboxylated aromatic compounds. After the adsorption tests, the residual benzoic acid concentrations were measured by UV-visible spectrometry, while the carbon nanotubes were characterized by TG and DTA thermal analyses and electron microscopy (SEM). The results show that the type of nanotubes thermally treated at 900 °C has the best performances in terms of adsorption rate and amounts of collected acid, even if compared with the performance of activated carbons.

Ion-imprinted sponge produced by ice template-assisted freeze drying of salecan and graphene oxide nanosheets for highly selective adsorption of mercury (II) ion

As a kind of potential heavy metal absorbent, polysaccharide-based materials are limited by the complicated preparation method and bad selectivity toward targeted ion. Here, a fantastic sponge was produced by combining salecan and graphene oxide (GO) nanosheets via ice template-assisted freeze drying and ion-imprinting technologies. The intense intermolecular interactions between salecan and GO gave the sponge high stability. The swelling, morphology, and mechanical stiffness of the material showed highly dependent on the salecan content. Additionally, the influence of salecan content, pH, initial ion concentration, and contact time on Hg²⁺ adsorption was extensively investigated. Adsorption kinetics and equilibrium isotherms perfectly fitted in the pseudo-second-order and Freundlich models, reflecting the multilayer chemical-adsorption mediated mechanism. Most strikingly, the ion-imprinted sponge exhibited strong selectivity toward Hg²⁺ and outstanding stability with recyclability over usage of five times. These investigations provide the guidance for the construction of promising polysaccharide-based adsorbents for the remediation of Hg²⁺-polluted water.

Non-monotonic contribution of nonionic surfactant on the retention of functionalized multi-walled carbon nanotubes in porous media

The concentration of nonionic surfactants like Triton X-100 (TX100) can influence the transport and fate of emerging contaminants (e.g., carbon nanotubes) in porous media, but limited research has previously addressed this issue. This study investigates the co-transport of functionalized multi-walled carbon nanotubes (MWCNTs) and various concentrations of TX100 in saturated quartz sand (QS). Batch experiments and molecular dynamics simulations were conducted to investigate the interactions between TX100 and MWCNTs. Results indicated that the concentration ratio of MWCNTs and TX100 strongly influences the dispersion of MWCNTs and interaction forces between MWCNTs and QS during the transport. Breakthrough curves of MWCNTs and TX100 and retention profiles of MWCNTs were determined and simulated in column studies. MWCNTs strongly enhanced the retention of TX100 in QS due to the high affinity of TX100 for MWCNTs. Conversely, the concentration of TX100 had a non-monotonic impact on MWCNT retention. The maximum transport of MWCNTs in the QS occurred at an input concentration of TX100 that was lower than the critical micelle concentration. This suggests that the relative importance of factors influencing MWCNTs changed with TX100 sorption. Results from interaction energy calculations and modeling of competitive blocking indicate that the predictive ability of interaction energy calculations and colloid filtration theory may be lost because TX100 mainly altered intermolecular forces between the MWCNT and porous media. This study provides new insights into the co-transport of surfactants and MWCNTs in porous media, which can be useful for environmental applications and risk management.

A trophic transfer study: accumulation of multi-walled carbon nanotubes associated to green algae in water flea Daphnia magna

Carbon nanotubes (CNT) are promising nanomaterials in modern nanotechnology and their use in many different applications leads to an inevitable release into the aquatic environment. In this study, we quantified trophic transfer of weathered multi-walled carbon nanotubes (wMWCNT) from green algae to primary consumer Daphnia magna in a concentration of 100 μg L^-1 using radioactive labeling of the carbon backbone (¹⁴C-wMWCNT). Trophic transfer of wMWCNT was compared to the uptake by daphnids exposed to nanomaterials in the water phase without algae. Due to the rather long observed CNT sedimentation times (DT) from the water phase (DT₅₀: 3.9 days (d), DT₉₀: 12.8 d) wMWCNT interact with aquatic organisms and associated to the green algae Chlamydomonas reinhardtii and Raphidocelis subcapitata. After the exposition of algae, the nanotubes accumulated to a maximum of 1.6 ± 0.4 μg ¹⁴C-wMWCNT mg^-1 dry weight^-1 (dw^-1) and 0.7 ± 0.3 μg ¹⁴C-wMWCNT mg^-1 dw^-1 after 24 h and 48 h, respectively. To study trophic transfer, R. subcapitata was loaded with ¹⁴C-wMWCNT and subsequently fed to D. magna. A maximum body burden of 0.07 ± 0.01 μg ¹⁴C-wMWCNT mg^-1 dw^-1 and 7.1 ± 1.5 μg ¹⁴C-wMWCNT mg^-1 dw^-1 for D. magna after trophic transfer and waterborne exposure was measured, respectively, indicating no CNT accumulation after short-term exposure via trophic transfer. Additionally, the animals eliminated nanomaterials from their guts, while feeding algae facilitated their excretion. Further, accumulation of ¹⁴C-wMWCNT in a growing population of D. magna revealed a maximum uptake of 0.7 ± 0.2 μg mg^-1 dw^-1. Therefore, the calculated bioaccumulation factor (BAF) after 28 d of 6700 ± 2900 L kg^-1 is above the limit that indicates a chemical is bioaccumulative in the European Union Regulation REACH. Although wMWCNT did not bioaccumulate in neonate D. magna after trophic transfer, wMWCNT enriched in a 28 d growing D. magna population regardless of daily feeding, which increases the risk of CNT accumulation along the aquatic food chain.

Nanofiber-Based Face Masks and Respirators as COVID-19 Protection: A Review

Wearing face masks, use of respirators, social distancing, and practicing personal hygiene are all measures to prevent the spread of the coronavirus disease (COVID-19). This pandemic has revealed the deficiency of face masks and respirators across the world. Therefore, significant efforts are needed to develop air filtration and purification technologies, as well as innovative, alternative antibacterial and antiviral treatment methods. It has become urgent—in order for humankind to have a sustainable future—to provide a feasible solution to air pollution, particularly to capture fine inhalable particulate matter in the air. In this review, we present, concisely, the air pollutants and adverse health effects correlated with long- and short-term exposure to humans; we provide information about certified face masks and respirators, their compositions, filtration mechanisms, and the variations between surgical masks and N95 respirators, in order to alleviate confusion and misinformation. Then, we summarize the electrospun nanofiber-based filters and their unique properties to improve the filtration efficiency of face masks and respirators.

Trends in the development of innovative nanobiocatalysts and their application in biocatalytic transformations

The ever-growing demand for cost-effective and innocuous biocatalytic transformations has prompted the rational design and development of robust biocatalytic tools. Enzyme immobilization technology lies in the formation of cooperative interactions between the tailored surface of the support and the enzyme of choice, which result in the fabrication of tremendous biocatalytic tools with desirable properties, complying with the current demands even on an industrial level. Different nanoscale materials (organic, inorganic, and green) have attracted great attention as immobilization matrices for single or multi-enzymatic systems. Aiming to unveil the potentialities of nanobiocatalytic systems, we present distinct immobilization strategies and give a thorough insight into the effect of nanosupports specific properties on the biocatalysts' structure and catalytic performance. We also highlight the development of nanobiocatalysts for their incorporation in cascade enzymatic processes and various types of batch and continuous-flow reactor systems. Remarkable emphasis is given on the application of such nanobiocatalytic tools in several biocatalytic transformations including bioremediation processes, biofuel production, and synthesis of bioactive compounds and fine chemicals for the food and pharmaceutical industry.

Fabrication of Carbon Nanofibers Decorated with Various Kinds of Metal Oxides for Battery Applications

Carbon nanofibers decorated with various metal oxide nanoparticles were fabricated by combining an electrospinning technique of bicomponent polymer mixture and a sol-gel reaction and subsequent carbonization process. Electrospun polymer nanofibers consisting of polyacrylonitrile (PAN) and poly(vinyl pyrrolidone) (PVP) with controllable diameters were fabricated with PAN/PVP core/shell types via phase-separation due to the immiscibility between two polymers. The electrospun nanofibers served as supporting materials with binding sites of PVP to incorporate titanium oxide precursor. Subsequently, the carbonization of the fibers led to the formation of carbon nanofibers@TiO2 for energy application, in which rutile TiO2 nanoparticles were decorated on the surface of carbon nanofiber. Especially, this TiO2 decorated carbon nanofiber electrode exhibited excellent electrochemical property in lithium-ion batteries (≈600 mA h g−1 at C/5 rate for 100 cycles). Furthermore, the carbon nanofibers were also successfully modified with other metal oxides, including NiO, SnO2, and ZrO2 nanoparticles, in a similar manner.

Critical review of photocatalytic disinfection of bacteria: from noble metals- and carbon nanomaterials-TiO2 composites to challenges of water characteristics and strategic solutions

This critical review covers ways to improve TiO₂-based photocatalysts, how water characteristics may affect photocatalytic disinfection, and strategies to tackle the challenges arising from water characteristics. Photocatalysis has shown much promise in the disinfection of water/wastewater, because photocatalysis does not produce toxic by-products, and is driven by green solar energy. There are however several drawbacks that are curbing the prevalence of photocatalytic disinfection applications: one, the efficiency of photocatalysts may limit popular utilization; two, the water characteristics may present some challenges to the process. TiO₂-based photocatalysts may be readily improved if composited with noble metals or carbon nanomaterials. Noble metals give TiO₂-based composites a higher affinity for dissolved oxygen, and induce plasmonic and Schottky effects in the TiO₂; carbon nanomaterials with a tunable structure, on the other hand, give the composites an improved charge carrier separation performance. Other than photocatalyst materials, the characteristics of water/wastewater is another crucial factor in the photocatalysis process. Also examined in this review are the crucial impacts that water characteristics have on photocatalysts and their interaction with bacteria. Accordingly, strategies to address the challenge of water characteristics on photocatalytic disinfection are explored: one, to modify the semiconductor conduction band to generate long-lifetime reactive species; two, to improve the interaction between bacteria and photocatalysts.

MnO2 -Based Materials for Environmental Applications

Manganese dioxide (MnO₂ ) is a promising photo-thermo-electric-responsive semiconductor material for environmental applications, owing to its various favorable properties. However, the unsatisfactory environmental purification efficiency of this material has limited its further applications. Fortunately, in the last few years, significant efforts have been undertaken for improving the environmental purification efficiency of this material and understanding its underlying mechanism. Here, the aim is to summarize the recent experimental and computational research progress in the modification of MnO₂ single species by morphology control, structure construction, facet engineering, and element doping. Moreover, the design and fabrication of MnO₂ -based composites via the construction of homojunctions and MnO₂ /semiconductor/conductor binary/ternary heterojunctions is discussed. Their applications in environmental purification systems, either as an adsorbent material for removing heavy metals, dyes, and microwave (MW) pollution, or as a thermal catalyst, photocatalyst, and electrocatalyst for the degradation of pollutants (water and gas, organic and inorganic) are also highlighted. Finally, the research gaps are summarized and a perspective on the challenges and the direction of future research in nanostructured MnO₂ -based materials in the field of environmental applications is presented. Therefore, basic guidance for rational design and fabrication of high-efficiency MnO₂ -based materials for comprehensive environmental applications is provided.

Effect of Aminated Chitosan-Coated Fe3O4 Nanoparticles with Applicational Potential in Nanomedicine on DPPG, DSPC, and POPC Langmuir Monolayers as Cell Membrane Models

An adsorption process of magnetite nanoparticles functionalized with aminated chitosan (Fe₃O₄-AChit) showing application potential in nanomedicine into cell membrane models was studied. The cell membrane models were formed using a Langmuir technique from three selected phospholipids with different polar head-groups as well as length and carbon saturation of alkyl chains. The research presented in this work reveals the existence of membrane model composition-dependent regulation of phospholipid-nanoparticle interactions. The influence of the positively charged Fe₃O₄-AChit nanoparticles on a Langmuir film stability, phase state, and textures is much greater in the case of these formed by negatively charged 1,2-dipalmitoyl-sn-glycero-3-phospho-rac-(1-glycerol) (DPPG) than those created by zwitterionic 1,2-distearoyl-sn-glycero-3-phosphocholine (DSPC) and 2-oleoyl-1-palmitoyl-sn-glycero-3-phosphocholine (POPC). The adsorption kinetics recorded during penetration experiments show that this effect is caused by the strongest adsorption of the investigated nanoparticles into the DPPG monolayer driven very likely by the electrostatic attraction. The differences in the adsorption strength of the Fe₃O₄-AChit nanoparticles into the Langmuir films formed by the phosphatidylcholines were also observed. The nanoparticles adsorbed more easily into more loosely packed POPC monolayer.

Similar toxicity mechanisms between graphene oxide and oxidized multi-walled carbon nanotubes in Microcystis aeruginosa

In photosynthetic microorganisms, the toxicity of carbon nanomaterials (CNMs) is typically characterized by a decrease in growth, viability, photosynthesis, as well as the induction of oxidative stress. However, it is currently unclear how the shape of the carbon structure in CNMs, such as in the 1-dimensional carbon nanotubes (CNTs) compared to the two-dimensional graphene oxide (GO), affects the way they interact with cells. In this study, the effects of GO and oxidized multi-walled CNTs were compared in the cyanobacterium Microcystis aeruginosa to determine the similarities or differences in how the two CNMs interact with and induce toxicity to cyanobacteria. Using change in Chlorophyll a concentrations, the effective concentrations inducing 50% inhibition (EC₅₀) at 96 h are found to be 11.1 μg/mL and 7.38 μg/mL for GO and CNTs, respectively. The EC₅₀ of the two CNMs were not found to be statistically different. Changes in fluorescein diacetate and 2',7'-dichlorodihydrofluorescein diacetate fluorescence, measured at the EC₅₀ concentrations, suggest a decrease in esterase enzyme activity but no oxidative stress. Scanning and transmission electron microscopy imaging did not show extensive membrane damage in cells exposed to GO or CNTs. Altogether, the decrease in metabolic activity and photosynthetic activity without oxidative stress or membrane damage support the hypothesis that both GO and CNTs induced indirect toxicity through physical mechanisms associated with light shading and cell aggregation. This indirect toxicity explains why the intrinsic differences in shape, size, and surface properties between CNTs and GO did not result in differences in how they induce toxicity to cyanobacteria.

Interactions between carbon-based nanoparticles and steroid hormone micropollutants in water

The occurrence of micropollutants (MPs) including steroid hormones is a global environmental and health challenge. Carbon-based nanoparticles can be incorporated with water treatment processes to allow MP removal by adsorption. The aim was to compare the suitability of such nanoparticles (graphene, graphene oxide, carbon nanotubes and C₆₀) to adsorb steroid hormones for later incorporation in membrane composites. All nanoparticles displayed fast kinetics; carbon nanotubes and graphene showed high adsorption capacities for hormones undeterminable in isotherm studies (over 10 mg/g). External surface adsorption appears to be the most prominent factor impacting adsorption performance. Structure, conformation, geometry and surface charge of nanoparticles can influence the accessibility of surface area through colloidal instability in aqueous solution. Mechanism inspection shows that adsorption initiates at long ranges (up to 10 nm) through hydrophobic and electrostatic interactions. At relatively short ranges (0.2-0.5 nm), adsorption is enhanced by π/π stacking, XH / π (X = C, O) interactions, van der Waals forces and hydrogen bonding. Both long- and short-range forces transporting hormones from the liquid bulk into the adsorbed phase could control the rate. With relatively short residence time required and high adsorption capacity, carbon nanotubes and graphene are promising for incorporation in a membrane composite.

New insights of metal free 2D graphitic carbon nitride for photocatalytic degradation of bisphenol A

Polymeric oxygen rich exfoliated graphitic carbon nitride (exfoliated GCN, EGCN) was synthesized by the acid treatment of bulk GCN. The photocatalyst was characterized using X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and point of zero charge. EGCN shows high valance band hole transfer under short-time visible light (λ > 420 nm) exposure for photocatalytic mineralization of bisphenol A (BPA). Enhanced BPA removal was achieved by EGCN (99 %) due to formation of OH^● radicals (H₂O/h_VB⁺ →OH^●/H⁺). Major factors affecting BPA degradation including catalyst dose, wide pH range, and pollutant concentration were optimized. Repeated cycles of BPA degradation were performed with negligible rate decreased from 0.045 to 0.029 min^-1. The degradation profile and plausible reaction mechanism of BPA was established and well justified by the byproducts identified by mass analysis HR-ESI-MS. Therefore, the as-synthesized metal free EGCN, active under visible light, offers a new platform for complete mineralization of byproducts of halogenated organic contaminants.

Impacts of carbon-based nanomaterials on nutrient removal in constructed wetlands: Microbial community structure, enzyme activities, and metabolism process

The increasing use of raw carbon-based nanomaterials (CBNs) will inevitably affect wastewater treatment systems. Constructed wetlands (CWs) are ecological wastewater treatment facilities and can intercept the vast particles pollutant, including CBNs. However, the impacts of CBNs on the treatment performance of CWs have no available knowledge. Therefore, we systematically inspected the effects of single-walled and multi-walled carbon nanotubes (SWCNTs and MWCNTs) and fullerene nanoparticles (C₆₀) on CW performance under 180-day exposure to 0, 10 and 1000 μg/L concentrations. The results showed that CBNs had marginally adverse impacts on chemical oxygen demand (COD) and total phosphorus (TP) removal, whereas nitrogen removal declined by 24.1 %-42.7 % following long-term exposure to CBNs. MWCNTs had the greatest inhibition effect on nitrogen removal, followed by SWCNTs and C₆₀. The CBNs also induced reactive oxygen species (ROS) overproduction as the increasing concentration, which confirmed that CBNs have biotoxic effects in CWs. The variation of functional microbial community and the inhibition of enzyme activities were the dominant reasons for the decline in nitrogen removal efficiency. Furthermore, predictive functional profiling showed that CBNs affected functional gene abundance, and caused a decline in the enzymes abundance connected to nitrogen removal by the end of the 180-day exposure period.

A high specific surface 1-(2-pyridylazo) 2-naphthol (PAN)-modified carbon-based silicon film with cellulose nanocrystalline structure for the efficient adsorption of rare-earth elements

Cellulose nanocrystalline solution forms a cellulose silicon film with a chiral phase sequence structure by self-assembly. The adsorption performance of silicon film to rare earth ions is improved by the two-step modification method.

Carbon Nanomaterials for Biomedical Application

The use of carbon-based nanomaterials (CNs) with outstanding properties has been rising in many scientific and industrial application fields. These CNs represent a tunable alternative for applications with biomolecules, which allow interactions in either covalent or noncovalent way. Diverse carbon-derived nanomaterial family exhibits unique features and has been widely exploited in various biomedical applications, including biosensing, diagnosis, cancer therapy, drug delivery, and tissue engineering. In this chapter, we aim to present an overview of CNs with a particular interest in intrinsic structural, electronic, and chemical properties. In particular, the detailed properties and features of CNs and its derivatives, including carbon nanotube (CNT), graphene, graphene oxide (GO), and reduced GO (rGO) are summarized. The interesting biomedical applications are also reviewed in order to offer an overview of the possible fields for scientific and industrial applications of CNs.

Gold-carbonaceous materials based heterostructures for gas sensing applications

The carbon nanostructures such as carbon nanotubes and graphene decorated with gold nanoparticles exhibit promising gas sensing applications with enhanced sensitivity.

Ultrasound-Assisted Surface Modification of MWCNT Using Organic Acids

In the present work, multiple-wall carbon nanotubes (MWCNTs) were surface modified in an environmentally friendly way, using low-frequency ultrasonic energy. This type of modification was carried-out using two different types of organic acids, citric acid (CA) and oxalic acid (OA). The modification of the MWCNTs was confirmed by Fourier-transform infrared spectroscopy (FTIR), where functional groups such as OH, C=O, O–C=O and COOH were detected. By means of Raman spectroscopy, an increase in carbon surface defects was found. On the other hand, using X-ray photoelectron spectroscopy (XPS), oxidation was evidenced on the surface of the modified MWCNT. In both Raman spectroscopy and XPS, the results indicate a greater modification when CA is used, possibly due to the fact that CA has a larger number of functional groups. MWCNT-CA showed good dispersion in methanol, while MWCNT-OA showed good stability in methanol and ethanol. Finally, a 20% removal of creatinine efficiency improvement was found with respect to the unmodified MWCNTs, while no improvement was found in the case of urea and uric acid.

Review on Carbon Nanotube Varieties for Healthcare Application: Effect of Preparation Methods and Mechanism Insight

Many potential uses of carbon nanotubes (CNT) in various sectors have created an urge to assess their diverse range of properties pertaining to various applications like catalysis, biosensor, and antimicrobial activity. Increasing studies on the biosensor and antibacterial activity of CNT have prompted tremendous interest in the utilization of the carbon-based nanostructured material as an alternative to currently existing antibiotics. However, the study of bactericidal aspects of this nanomaterial is relatively new and hence the deeper understanding of the various physicochemical characteristics and antimicrobial nature of CNT is extremely wanted. This review covers the effect of framework substitution and explains the understanding of membrane disintegration and oxidative stresses upon nanomaterials for antimicrobial activity. The present article has also reviewed effect of preparation nanoparticle deposition and framework modification on carbon nanotube structure. The recent research on graphene-modified nanomaterials for biosensor applications related to healthcare/clinical applications have also been discussed. Major physicochemical contributing factors such as size, functionalization, high surface area, and aggregation features of CNT assisting in the bacterial killing have nicely been outlined. Hence, the present review explains the supporting information related with Single and multi-walled carbon nanotube and summarized the advantages of functionalized carbon nanotube/graphene-based nanostructured carbon-based materials towards protection and reduction of bacterial/viral infections in the healthcare sector.

Production, properties, and catalytic applications of sludge derived biochar for environmental remediation

Environment-friendly and cost-effective disposal and reutilization of sludge wastes are essential in wastewater treatment processes (WWTPs). Converting activated sludge into biochar via thermochemical treatment is a promising technology for waste management in WWTPs. This review summarizes the compositions of sludge, the dewatering methods, and the thermochemical methods whichinfluence the structures, chemistry, and catalytic performances of the derived biochar. Moreover, the physiochemical characteristics and chemical stability of sludge biochar are discussed. Catalytic applications of biochar are highlighted, including the reaction mechanisms and feasibility for catalytic removal of organic contaminants. High-temperature carbonized sludge biochar exhibits excellent performance for persulfate activation in advanced oxidation processes due to the graphitic carbon structure, newly-created active sites, and fine-tuned metal species. Therefore, the sludge biochar can be produced via cost-effective and eco-friendly approaches to immobilize harmful components from sludge and remediate organic pollution in wastewater, offering a sustainable route toward sludge reutilization into value-added products for water purification.

Quantification of spinosyn A and spinosyn D in animal-derived products using multiwalled carbon nanotubes coupled with LC-MS/MS for analysis

An analytical method was developed for the quantification of spinosad (sum of spinosyns A and D) in five animal-derived products (chicken breast, pork, beef, egg, and milk) using LC-MS/MS. The sample was extracted using acetonitrile/1% acetic acid and a combination of magnesium sulfate and sodium acetate salts. The sample was purified using multiwalled carbon nanotubes as sorbent via a dispersive-solid-phase extraction procedure. Matrix-matched calibration (seven-point) provided good linearity with coefficient of determination (R² ) ≥0.99 for each product. The limits of detection and quantification (LOQs) ranged between 0.0003-0.03 and 0.001-0.1 mg/kg, respectively. Method validation was carried out after spiking the target standard to blank matrices at the concentration levels of LOQ, 2 × LOQ, and 10 × LOQ with three replicates for each. The average recoveries were between 74 and 104%, with relative standard deviations ≤9.68, which were within the acceptable range designated by the international organizations. The developed method was successfully applied for monitoring market samples collected throughout the Korean Peninsula, and none of the samples tested positive for the target analytes. It has therefore been shown that dehydration and acidification were effective to extract spinosad from animal-derived products.

Development and Application of Resistance Strain Force Sensors

Resistance strain force sensors have been applied to monitor the strains in various parts and structures for industrial use. Here, we review the working principles, structural forms, and fabrication processes for resistance strain gauges. In particular, we focus on recent developments in resistance stress transfer for resistance strain force sensors and the creep effect due to sustained loads and/or temperature variations. Various error compensation methods to reduce the creep effect are analyzed to develop a metrology standard for resistance strain force sensors. Additionally, the current status of carbon nanotubes (CNTs), silicon carbide (SiC), gallium nitride (GaN), and other wide band gap semiconductors for a wide range of strain sensors are reviewed. The technical requirements and key issues of resistance strain force sensors for future applications are presented.

Development and Application of a Multi-Residue Method to Determine Pesticides in Agricultural Water Using QuEChERS Extraction and LC-MS/MS Analysis

Agricultural water is closely linked to surface and ground water as well as soil; hence, ensuring its safety is an important endeavor. We used the “quick, easy, cheap, effective, rugged, and safe” (QuEChERS) method to analyze multi-residue pesticides in agricultural water by using a combined-sorbent-based clean-up procedure. Among the various sorbents examined, clean-up using ENVI-Carb combined with a primary secondary amine sorbent delivered the highest recovery of multi-residue pesticides (>93.9%). While the developed method showed satisfactory linearity (R2 > 0.9991), precision, and specificity, recovery was low for pyrazolate (29.1%) and thidiazuron (59.2%). The limits of detection and quantification for the 55 pesticides targeted in this study were in 0.02–3.0 μg L−1 and 0.1–9.9 μg L−1, respectively. The developed method was used to identify and quantify multi-residue pesticides during sample analysis. The results suggest that the QuEChERS method employing a combination of ENVI-Carb and another sorbent can be applied for the effective analysis of multi-residue pesticides in agricultural water.

Surface quinone-induced formation of aqueous reactive sulfur species controls pine wood biochar-mediated reductive dechlorination of hexachloroethane by sulfide

Understanding the mechanisms controlling the redox transformation of organic contaminants mediated by biochar is of great significance for application of biochar in remediation of contaminated soils and sediments. Here we investigated the mediation effect of a pine wood-derived biochar (P-char) in comparison with multiwalled carbon nanotubes (MCNTs) and graphite on the reductive dechlorination of hexachloroethane by sulfide. Upon normalization of the mediator's surface area, the reduction rate of hexachloroethane follows an order of P-char < MCNTs < graphite. Aqueous polysulfides and polysulfide free radicals were readily produced by reacting sulfide only with P-char, and the supernatant separated from the reaction system could account for 83.4% of the pseudo-kinetic rate constant of hexachloroethane mediated by P-char. In contrast, MCNTs and graphite had weak abilities to produce reactive sulfur species, and the supernatant exhibited very low reduction capability (<20.7%) of hexachloroethane. Electron paramagnetic resonance (EPR) analysis demonstrated that the surface quinone moieties on P-char induced the formation of polysulfides and polysulfide free radicals from sulfide by serving as one-electron acceptors. Consistently, polysulfides prepared by reacting elemental sulfur with sulfide showed much stronger reducing capability compared to sulfide. Thus, the mediation effect of P-char was dominantly attributed to the surface quinone-induced formation of reactive reducing sulfur species, whereas the mediation effect of MCNTs and graphite mainly stemmed from the enhanced electron transfer by the graphitized carbon. These results showed for the first time that surface quinone-induced formation of aqueous reactive sulfur species could control biochar-mediated reductive dechlorination of chloroorganic contaminants by sulfides.

Enhancing the Thermal Performance of a Stearate Phase Change Material with Graphene Nanoplatelets and MgO Nanoparticles

The effectiveness of dispersed nanomaterials to improve the thermal performance of phase change materials (PCMs) is well-proven in the literature. The proposal of new engineered nanoenhanced phase change materials (NePCMs) with customized characteristics may lead to more efficient thermal energy storage (TES) systems. This work is focused on the development of new NePCMs based on the dispersions of graphene nanoplatelets (GnPs) or MgO nanoparticles in a stearate PCM. The new proposed materials were synthesized using a two-step method, and acetic acid was selected as a surfactant to improve the stability of the dispersions. An extensive characterization of the constitutive materials and the developed dispersions using different spectroscopy techniques is reported. Also, the GnP nanopowder was explored by using the XPS technique with the aim to characterize the used carbon nanomaterial. The obtained spectra were investigated in terms of the chemical bonds related to the observed peaks. The thermophysical profile (density, thermal conductivity, isobaric heat capacity, and thermal diffusivity) was experimentally determined once the main components of the NePCMs were characterized and dispersions were designed and developed. This discussion focuses on the differentiated and distinguished effects of the dispersed GnPs and MgO on the properties of the NePCMs. A comprehensive analysis of the measurements to elucidate the mechanism that promoted higher improvements using GnPs instead of MgO was performed.

A decennary update on applications of metal nanoparticles (MNPs) in the synthesis of nitrogen- and oxygen-containing heterocyclic scaffolds

Heterocycles have been found to be of much importance as several nitrogen- and oxygen-containing heterocycle compounds exist amongst the various USFDA-approved drugs. Because of the advancement of nanotechnology, nanocatalysis has found abundant applications in the synthesis of heterocyclic compounds. Numerous nanoparticles (NPs) have been utilized for several organic transformations, which led us to make dedicated efforts for the complete coverage of applications of metal nanoparticles (MNPs) in the synthesis of heterocyclic scaffolds reported from 2010 to 2019. Our emphasize during the coverage of catalyzed reactions of the various MNPs such as Ag, Au, Co, Cu, Fe, Ni, Pd, Pt, Rh, Ru, Si, Ti, and Zn has not only been on nanoparticles catalyzed synthetic transformations for the synthesis of heterocyclic scaffolds, but also provide an inherent framework for the reader to select a suitable catalytic system of interest for the synthesis of desired heterocyclic scaffold.

A QM/MD Coupling Method to Model the Ion-Induced Polarization of Graphene

We report a new Quantum Mechanical/Molecular Dynamics (QM/MD) simulation loop to model the coupling between the electron and atom dynamics in solid/liquid interfacial systems. The method can describe simultaneously both the quantum mechanical surface polarizability emerging from the proximity to the electrolyte and the electrolyte structure and dynamics. In the current setup, Density Functional Tight Binding calculations for the electronic structure calculations of the surface are coupled with classical molecular dynamics to simulate the electrolyte solution. The reduced computational cost of the QM part makes the coupling with a classical simulation engine computationally feasible and allows simulation of large systems for hundreds of nanoseconds. We tested the method by simulating both a noncharged graphene flake and a noncharged and charged infinite graphene sheet immersed in an NaCl electrolyte solution. We found that, when no bias is applied, ions preferentially remained in solution, and only cations are mildly attracted to the surface of the graphene. This preferential adsorption of cations vs anions seems to persist also when the surface is moderately charged and rules out any substantial ions/surface charge transfer.

Challenges in Design and Fabrication of Flexible/Stretchable Carbon- and Textile-Based Wearable Sensors for Health Monitoring: A Critical Review

To demonstrate the wearable flexible/stretchable health-monitoring sensor, it is necessary to develop advanced functional materials and fabrication technologies. Among the various developed materials and fabrication processes for wearable sensors, carbon-based materials and textile-based configurations are considered as promising approaches due to their outstanding characteristics such as high conductivity, lightweight, high mechanical properties, wearability, and biocompatibility. Despite these advantages, in order to realize practical wearable applications, electrical and mechanical performances such as sensitivity, stability, and long-term use are still not satisfied. Accordingly, in this review, we describe recent advances in process technologies to fabricate advanced carbon-based materials and textile-based sensors, followed by their applications such as human activity and electrophysiological sensors. Furthermore, we discuss the remaining challenges for both carbon- and textile-based wearable sensors and then suggest effective strategies to realize the wearable sensors in health monitoring.

Experimental Investigation of the Mechanical and Surface Properties of Sub-Micron Carbon Spheres

This study investigates the mechanical and surface properties of spherical carbon particles. Sub-micrometer carbon spheres were previously used as oil additives to improve the tribological performance of oils, and as anode material to enhance the storage of rechargeable lithium-ion batteries. In the current work, internal structure and chemical analysis of these carbon sphere particles was conducted via focus ion beam scanning electron microscopy, and the results revealed that the carbon sphere particles are pure carbon particles with a solid internal structure. Atomic force microscopy (AFM) and nano-indenter were utilized to explore the mechanical properties (hardness and elastic modulus) of carbon sphere particles. The obtained results showed that the carbon spheres have an elastic modulus in the range of 10 to 42 GPa, while their hardness is in the range of 0.5 to 2.6 GPa. Besides, the AFM scans confirmed that the carbon particles are entirely separated and devoid of agglomeration. These results support the viable use of carbon sphere particles in various engineering applications.

Effect of Nano-Graphene Oxide and n-Butanol Fuel Additives Blended with Diesel—Nigella sativa Biodiesel Fuel Emulsion on Diesel Engine Characteristics

The present investigation uses a blend of Nigella sativa biodiesel, diesel, n-butanol, and graphene oxide nanoparticles to enhance the performance, combustion and symmetric characteristics and to reduce the emissions from the diesel engine of a modified common rail direct injection (CRDI). A symmetric toroidal-type combustion chamber and a six-hole solenoid fuel injector were used in the current investigation. The research aimed to study the effect of two fuel additives, n-butanol and synthesized asymmetric graphene oxide nanoparticles, in improving the fuel properties of Nigella sativa biodiesel (NSME25). The concentration of n-butanol (10%) was kept constant, and asymmetric graphene oxide nano-additive and sodium dodecyl benzene sulphonate (SDBS) surfactant were added to n-butanol and NSME25 in the form of nanofluid in varying proportions. The nanofluids were prepared using a probe sonication process to prevent nanoparticles from agglomerating in the base fluid. The process was repeated for biodiesel, n-butanol and nanofluid, and four different stable and symmetric nanofuel mixtures were prepared by varying the graphene oxide (30, 60, 90 and 120 ppm). The nanofuel blend NSME25B10GO90 displayed an enhancement in the brake thermal efficiency (BTE) and a reduction in brake-specific fuel consumption (BSFC) at maximum load due to high catalytic activity and the enhanced microexplosion phenomenon developed by graphene oxide nanoparticles. The heat release rate (HRR), in-cylinder temperature increased, while exhaust gas temperature (EGT) decreased. Smoke, hydrocarbon (HC), carbon monoxide (CO2) and carbon monoxide (CO) emissions also fell, in a trade-off with marginally increased NOx, for all nanofuel blends, compared with Nigella sativa biodiesel. The results obtained indicates that 90 ppm of graphene oxide nanoparticles and 10% n-butanol in Nigella sativa biodiesel are comparable with diesel fuel.

Enhanced adsorption of bisphenol A, tylosin, and tetracycline from aqueous solution to nitrogen-doped multiwall carbon nanotubes via cation-π and π-π electron-donor-acceptor (EDA) interactions

Doping heteroatoms in carbon nanotubes can substantially enhance the electronic polarizability of the carbon surface and thus may facilitate adsorptive interactions of organic contaminants. Here, the adsorption isotherms of three polar/ionizable emerging organic contaminants, bisphenol A, tylosin, and tetracycline from aqueous solutions to synthesized heteroatom nitrogen-doped multiwall carbon nanotubes (N-MCNT) were compared with those to commercial non-doped multiwall carbon nanotubes (MCNT) at pH ~ 6. N-MCNT exhibited much stronger adsorption (3-4 folds higher sorption distribution coefficients, K_d) towards the three adsorbates than MCNT. The hydroxyl group-substituted bisphenol A molecule is rich in π-electrons and thus interacts with the polarized π-electron-depleted N-heterocyclic aromatic ring on N-MCNT via π-π electron-donor-acceptor (EDA) interaction, whereas the protonated amino group and enone groups in the tylosin molecule are deficient in electrons and interact with the neighboring π-electron-rich aromatic ring on N-MCNT via cation-π and π-π EDA interactions, respectively. The tetracycline molecule contains both electron-rich moiety (phenol ring) and electron-depleted moieties (protonated amino group and enone groups), which interact with the corresponding π-electron-acceptor/donor sites on N-MCNT. The proposed adsorption mechanisms were tested by the effects of ionic strength (NaCl or CaCl₂), co-present Cu²⁺ ion, and changing pH on adsorption, and further by the adsorption behavior of a model organic cation (tetraethylamine). These results indicate that enhanced adsorption of emerging organic contaminants to carbon nanotubes can be achieved by doping with heterocyclic nitrogen atoms to facilitate specific EDA interactions. Capsule: Nitrogen-doped multiwall carbon nanotubes exhibit enhanced adsorptive removal of bisphenol A, tylosin, and tetracycline from aqueous solutions.

The research trends of metal-organic frameworks in environmental science: a review based on bibliometric analysis

Metal-organic frameworks, an emerging class of porous material, have developed rapidly in recent years. In order to clarify the application of metal-organic frameworks in the field of environmental science, 1386 articles over the last 20 years were obtained from Scopus and analysed by the bibliometric method. And the collaboration between countries, institutions and authors and the co-occurrence of keywords were also conducted using VOSviewer. The results indicated that this area of research has entered a fast-developing stage. The number of articles published has grown from 7 articles in 1999 to 378 articles in 2018. The most productive country was China with 626 articles published. The most productive institution was the Chinese Academy of Sciences, and the most productive author was Jhung SH from Kyungpook National University of South Korea. Although metal-organic frameworks have been widely used in adsorption and catalytic degradation of pollutants from the environment, the removal mechanism of pollutants by MOFs, the stability improvement and the cost reduction of metal-organic frameworks are still the main challenges for their practical applications.

Tunable Molybdenum Disulfide-Enabled Fiber Mats for High-Efficiency Removal of Mercury from Water

The application of molybdenum disulfide (MoS₂) for water decontamination is expanded toward a novel approach for mercury removal using nanofibrous mats coated with MoS₂. A bottom-up synthesis method for growing MoS₂ on carbon nanofibers was employed to maximize the nanocomposite decontamination potential while minimizing the release of the nanomaterial to treated water. First, a co-polymer of polyacrylonitrile and polystyrene was electrospun as nanofibrous mats and pretreated to form pristine carbon fibers. Next, three solvothermal methods of controlled in situ MoS₂ growth of different morphologies were achieved on the surface of the fibers using three different sets of precursors. Finally, these MoS₂-enabled fibers were extensively characterized and evaluated for their mercuric removal efficiency. Two mercury removal mechanisms, including reduction-oxidation reactions and physicochemical adsorption, were elucidated. The two nanocomposites with the fastest (0.436 min^-1 mg^-1) and highest mercury removal (6258.7 mg g^-1) were then further optimized through intercalation with poly(vinylpyrrolidone), which increased the MoS₂ interlayer distance from 0.68 nm to more than 0.90 nm. The final, optimal fabrication technique (evaluated according to mercuric capacity, kinetics, and nanocomposite stability) demonstrated five times higher adsorption than the second-best method and obtained 70% of the theoretical mercury adsorption capacity of MoS₂. Overall, results from this study indicate an alternative, advanced material to increase the efficiency of aqueous mercury removal while also providing the basis for other novel environmental applications such as selective sensing, disinfection, and photocatalysis.

Influence of Carbon Quantum Dots on the Biome

The latest class of engineered nanomaterials, viz., carbon quantum dots (CQDs), has attracted attention because they are synthesized through green chemical procedures and from organic waste matter. The synthesis of these nano-sized particles synthesized from biomass such as fruit peel and other organic matter results in mixtures of CQD species that differ in chemical identity, activity and photo-physical properties. Generally used collectively as chemically heterogeneous ensemble, they have already had an impact on multiple sectors of our environment by use as wastewater sensors, switches, model agro-fertilizers, and in biomedicine. The transitioning of their applications to crops is an important crossover point that calls for an accurate and detailed assessment of their genomic, proteomic, and metabolomics impact on agriculturally important crops and produce. We review the current status of CQDs vis-à-vis their impact on the biosphere via recent model studies and comment on the knowledge gaps that need to be bridged to ensure their safe use in agronomy. A detailed knowledge of their impact on aquatic systems and the food-chain is critical for human and environmental safety and sustainability.

Exogenous application of NaBiF4 nanoparticle affects wheat root development

BACKGROUND

Nanoparticle causes soil pollution, which affected plant development and then resulted in biomass decreased, especially in crops. However, little is known how sodium nanoparticles affect wheat root development at plant physiological level.

RESULTS

We used NaBiF4 (size of 50-100 nm) to analyze the effect in wheat development at plant physiological level. Under exogenous application of 50 μM NaBiF4 for treatment, wheat root elongation was inhibited, but fresh weight and dry weight were increased. We also found that NaBiF4 induced that the plant had lower content of sodium than negative control. Used no-sodium nanoparticle of BiF3 for another negative control, it was also supported that NaBiF4 entered into cell to replace of sodium and exported sodium out of plant. These results implied NaBiF4 might induce sodium export to maintain the balance between sodium and potassium elements. Additionally, metabolism analysis demonstrated that SOD activity was increased, but CAT and POD activity reduced under exogenous treatment of NaBiF4 nanoparticles.

CONCLUSIONS

Sodium nanoparticles (NaBiF4) inhibited plant development by nanoparticle accumulation and sodium homeostasis broken, and then involved reactive oxygen species (ROS) signaling system response. These results provided more sights of sodium nanoparticle effect in plant development.

Progress in supercapacitors: roles of two dimensional nanotubular materials

Overcoming the global energy crisis due to vast economic expansion with the advent of human reliance on energy-consuming labor-saving devices necessitates the demand for next-generation technologies in the form of cleaner energy storage devices. The technology accelerates with the pace of developing energy storage devices to meet the requirements wherever an unanticipated burst of power is indeed needed in a very short time. Supercapacitors are predicted to be future power vehicles because they promise faster charging times and do not rely on rare elements such as lithium. At the same time, they are key nanoscale device elements for high-frequency noise filtering with the capability of storing and releasing energy by electrostatic interactions between the ions in the electrolyte and the charge accumulated at the active electrode during the charge/discharge process. There have been several developments to increase the functionality of electrodes or finding a new electrolyte for higher energy density, but this field is still open to witness the developments in reliable materials-based energy technologies. Nanoscale materials have emerged as promising candidates for the electrode choice, especially in 2D sheet and folded tubular network forms. Due to their unique hierarchical architecture, excellent electrical and mechanical properties, and high specific surface area, nanotubular networks have been widely investigated as efficient electrode materials in supercapacitors, while maintaining their inherent characteristics of high power and long cycling life. In this review, we briefly present the evolution, classification, functionality, and application of supercapacitors from the viewpoint of nanostructured materials to apprehend the mechanism and construction of advanced supercapacitors for next-generation storage devices.