Carbon Nanotube Gas and Vapor Sensors

Sn powder as reducing agents and SnO2 precursors for the synthesis of SnO2-reduced graphene oxide hybrid nanoparticles

A facile approach to prepare SnO2/rGO (reduced graphene oxide) hybrid nanoparticles by a direct redox reaction between graphene oxide (GO) and tin powder was developed. Since no acid was used, it is an environmentally friendly green method. The SnO2/rGO hybrid nanoparticles were characterized by ultraviolet-visible spectroscopy, Raman spectroscopy, thermogravimetric analysis, X-ray diffraction analysis, and X-ray photoelectron spectroscopy. The microstructure of the SnO2/rGO was observed with scanning electron microscopy and transmission electron microscopy. The tin powder efficiently reduced GO to rGO, and the Sn was transformed to SnO2 nanoparticles (∼45 nm) that were evenly distributed on the rGO sheets. The SnO2/rGO hybrid nanoparticles were then coated on an interdigital electrode to fabricate a humidity sensor, which have an especially good linear impedance response from 11% to 85% relative humidity.

Silicon nanowire-based devices for gas-phase sensing

Since their introduction in 2001, SiNW-based sensor devices have attracted considerable interest as a general platform for ultra-sensitive, electrical detection of biological and chemical species. Most studies focus on detecting, sensing and monitoring analytes in aqueous solution, but the number of studies on sensing gases and vapors using SiNW-based devices is increasing. This review gives an overview of selected research papers related to the application of electrical SiNW-based devices in the gas phase that have been reported over the past 10 years. Special attention is given to surface modification strategies and the sensing principles involved. In addition, future steps and technological challenges in this field are addressed.

Preparation of magnetic carbon nanotubes (Mag-CNTs) for biomedical and biotechnological applications

Carbon nanotubes (CNTs) have been widely studied for their potential applications in many fields from nanotechnology to biomedicine. The preparation of magnetic CNTs (Mag-CNTs) opens new avenues in nanobiotechnology and biomedical applications as a consequence of their multiple properties embedded within the same moiety. Several preparation techniques have been developed during the last few years to obtain magnetic CNTs: grafting or filling nanotubes with magnetic ferrofluids or attachment of magnetic nanoparticles to CNTs or their polymeric coating. These strategies allow the generation of novel versatile systems that can be employed in many biotechnological or biomedical fields. Here, we review and discuss the most recent papers dealing with the preparation of magnetic CNTs and their application in biomedical and biotechnological fields.

A NEW NONLOCAL BEAM THEORY WITH THICKNESS STRETCHING EFFECT FOR NANOBEAMS

This paper presents a new nonlocal thickness-stretching sinusoidal shear deformation beam theory for the static and vibration of nanobeams. The present model incorporates the length scale parameter (nonlocal parameter) which can capture the small scale effect, and it accounts for both shear deformation and thickness stretching effects by a sinusoidal variation of all displacements through the thickness without using shear correction factor. Based on the nonlocal differential constitutive relations of Eringen, the equations of motion of the nanobeam are derived using Hamilton's principle. The effects of nonlocal parameter, aspect ratio and the thickness stretching on the static and dynamic responses of the nanobeam are discussed. The theoretical development presented herein may serve as a reference for nonlocal theories as applied to the bending and dynamic behaviors of complex-nanobeam-system such as complex carbon nanotube system.

PANI and graphene/PANI nanocomposite films--comparative toluene gas sensing behavior

The present work discusses and compares the toluene sensing behavior of polyaniline (PANI) and graphene/polyaniline nanocomposite (C-PANI) films. The graphene–PANI ratio in the nanocomposite polymer film is optimized at 1:2. For this, N-methyl-2-pyrrolidone (NMP) solvent is used to prepare PANI-NMP solution as well as graphene-PANI-NMP solution. The films are later annealed at 230 °C, characterized using scanning electron microscopy (SEM) as well Fourier transform infrared spectroscopy (FTIR) and tested for their sensing behavior towards toluene. The sensing behaviors of the films are analyzed at different temperatures (30, 50 and 100 °C) for 100 ppm toluene in air. The nanocomposite C-PANI films have exhibited better overall toluene sensing behavior in terms of sensor response, response and recovery time as well as repeatability. Although the sensor response of PANI (12.6 at 30 °C, 38.4 at 100 °C) is comparatively higher than that of C-PANI (8.4 at 30 °C, 35.5 at 100 °C), response and recovery time of PANI and C-PANI varies with operating temperature. C-PANI at 50 °C seems to have better toluene sensing behavior in terms of response time and recovery time.

Peroxidase-mediated biodegradation of carbon nanotubes in vitro and in vivo

As a result of their unique electronic, optical, and mechanical properties, carbon nanotubes (CNTs) have been implemented in therapeutic and imaging applications. In an idealized situation, CNTs would be disposed of after they transport their theranostic payloads. Biodegradation represents an attractive pathway for the elimination of CNT carriers post-delivery and may be integral in catalyzing the release of the cargo from the delivery vehicle. Accordingly, recent research efforts have focused on peroxidase-driven biodegradation of CNTs. In this review, we not only summarize recent efforts to biodegrade CNTs in the test tube, in vitro, and in vivo, but also attempt to explore the fundamental parameters underlying degradation. Encouraged by the in vivo results obtained to date, we envision a future, where carbon-based nano-containers, which are specifically designed to target organs/cells, deliver their cargo, and biodegrade via peroxidase-driven mechanism, will represent an attractive therapeutic delivery option in nanomedicine.

Forced assembly of water-dispersible carbon nanotubes trapped in paper for cheap gas sensors

A versatile and readily scalable approach to fabricate a cheap and sensitive paper gas sensor is described. Chemically acidified single-walled carbon nanotubes are assembled in paper, forming continuous sensing arrays with a low detection limit and high detection selectivity for ammonia gas.

DNA gold nanoparticle nanocomposite films for chemiresistive vapor sensing

Chemiresistive vapor sensors combining functionalized gold nanoparticles and single-stranded DNA oligomers are investigated to enhance specificity in chemical sensing. Sensors are made by depositing DNA-functionalized gold nanoparticles onto microfabricated electrodes using four distinct sequences. Sensor performance is evaluated for response to relative humidity and exposure to vapor analytes including ethanol, methanol, hexane, dimethyl methylphosphonate, and toluene under different relative humidity. It is found that sensors display a nonmonotonic resistance change toward increasing humidity due to the combined effects of hydration induced swelling and ionic conduction. Responses to vapor analytes show sequence-dependent patterns as well as a strong influence of humidity. Overall, the findings are encouraging for using DNA oligomers to enhance specificity in chemical sensing.

Sensor arrays from multicomponent micropatterned nanoparticles and graphene

A novel approach for multicomponent patterning metal/metal oxide nanoparticles on graphene was developed, which involves region-specific plasma treatment, followed by region-selective substrate-enhanced electroless deposition of Au nanoparticles and solution alkalization of ferrous chloride tetrahydrate in the presence of ammonia into Fe3O4 nanoparticles. The resultant Fe3O4/Au multicomponent micropatterned-graphene films were found to be highly selective sensor arrays for detecting low levels of chemical vapor molecules at ppm levels. This novel concept could be applied to the development of various multicomponent patterned nanomaterials for many potential applications, ranging from nanoscale region-specific chemical-/bio-sensor arrays to multifunctional optoelectronic devices.

Nanocomposite based flexible ultrasensitive resistive gas sensor for chemical reactions studies

Room temperature operation, low detection limit and fast response time are highly desirable for a wide range of gas sensing applications. However, the available gas sensors suffer mainly from high temperature operation or external stimulation for response/recovery. Here, we report an ultrasensitive-flexible-silver-nanoparticle based nanocomposite resistive sensor for ammonia detection and established the sensing mechanism. We show that the nanocomposite can detect ammonia as low as 500 parts-per-trillion at room temperature in a minute time. Furthermore, the evolution of ammonia from different chemical reactions has been demonstrated using the nanocomposite sensor as an example. Our results demonstrate the proof-of-concept for the new detector to be used in several applications including homeland security, environmental pollution and leak detection in research laboratories and many others.

Rapid prototyping of carbon-based chemiresistive gas sensors on paper

Chemically functionalized carbon nanotubes (CNTs) are promising materials for sensing of gases and volatile organic compounds. However, the poor solubility of carbon nanotubes hinders their chemical functionalization and the subsequent integration of these materials into devices. This manuscript describes a solvent-free procedure for rapid prototyping of selective chemiresistors from CNTs and graphite on the surface of paper. This procedure enables fabrication of functional gas sensors from commercially available starting materials in less than 15 min. The first step of this procedure involves the generation of solid composites of CNTs or graphite with small molecule selectors--designed to interact with specific classes of gaseous analytes--by solvent-free mechanical mixing in a ball mill and subsequent compression. The second step involves deposition of chemiresistive sensors by mechanical abrasion of these solid composites onto the surface of paper. Parallel fabrication of multiple chemiresistors from diverse composites rapidly generates cross-reactive arrays capable of sensing and differentiating gases and volatile organic compounds at part-per-million and part-per-thousand concentrations.

Trace level ammonia sensing by SWCNTs (network/film) based resistive sensor using a simple approach in sensor development and design

Highly stable and sensitive detection of trace level (approximately 1 ppm) of NH3 gas at room temperature is demonstrated for single wall carbon nanotube (SWCNT)-based resistive sensor. The sensor device was comprised of two planer Au electrodes deposited on carbon nanotubes (CNTs) by thermal evaporation method followed by patterning with photolithography process. For the growth of high-quality SWCNTs, multiple catalysts were deposited by co-sputtering method, and the yielded CNTs were in the diameter range of 0.8 to 1.5 nm. The CNTs were characterized by various techniques including Raman spectroscopy, field emission scanning electron microscopy, and transmission electron microscopy. As-grown SWCNTs-based resistive sensor showed an excellent variation in sensor response in the trace sensing range from 1 to 50 ppm of NH3 where the sensor response linearly increased with NH3 concentration. The sensing mechanism was attributed to the electron transfer to the SWCNTs as a result of NH3 oxidation on the nanotube surface. The sensor was found to have good sensitivity with a response time of a few minutes at room temperature. Sensor recovery posed a great problem at room temperature, and the fast and complete recovery was successfully achieved by using appropriate thermal treatment protocol.

A remote sensor for detecting methane based on palladium-decorated single walled carbon nanotubes

The remote detection of the concentration of methane at room temperature is performed by a sensor that is configured by the combination of radio frequency identification (RFID), and functionalized carbon nanotubes (CNTs). The proposed sensor is schemed as a thin film RFID tag in a polyethylene substrate, on which a metal trace dipole, a metal trace T impedance matching networks, a 0.5 μm-CMOS RF/DC rectifier chipset and a sensor head of palladium-decorated single walled carbon nanotubes (Pd-SWCNTs) are surface mounted in cascade. The performances of the sensor are examined and described by the defined parameters of the received signal strength index (RSSI) and the comparative analog identifier (ΔAID). Results validate the sensor's ability to detect molecules of methane at room temperature, showing that the RSSI can increase 4 dB and the ΔAID can increase 3% in response to methane concentrations ranging from zero to 100 ppm.

High performance field-effect ammonia sensors based on a structured ultrathin organic semiconductor film

High performance organic field-effect transistor (OFET)-based ammonia sensors are demonstrated with ultrathin (4-6 molecular layers) dendritic microstripes of an organic semiconductor prepared via dip-coating. These sensors exhibit high sensitivity, fast response/recovery rate, good selectivity, low concentration detection ability, and reliable reversibility, as well as stability. Such a performance represents great progress in the field of OFET-based sensors.

Surface charge and cellular processing of covalently functionalized multiwall carbon nanotubes determine pulmonary toxicity

Functionalized carbon nanotubes (f-CNTs) are being produced in increased volume because of the ease of dispersion and maintenance of the pristine material physicochemical properties when used in composite materials as well as for other commercial applications. However, the potential adverse effects of f-CNTs have not been quantitatively or systematically explored. In this study, we used a library of covalently functionalized multiwall carbon nanotubes (f-MWCNTs), established from the same starting material, to assess the impact of surface charge in a predictive toxicological model that relates the tubes' pro-inflammatory and pro-fibrogenic effects at cellular level to the development of pulmonary fibrosis. Carboxylate (COOH), polyethylene glycol (PEG), amine (NH2), sidewall amine (sw-NH2), and polyetherimide (PEI)-modified MWCNTs were successfully established from raw or as-prepared (AP-) MWCNTs and comprehensively characterized by TEM, XPS, FTIR, and DLS to obtain information about morphology, length, degree of functionalization, hydrodynamic size, and surface charge. Cellular screening in BEAS-2B and THP-1 cells showed that, compared to AP-MWCNTs, anionic functionalization (COOH and PEG) decreased the production of pro-fibrogenic cytokines and growth factors (including IL-1β, TGF-β1, and PDGF-AA), while neutral and weak cationic functionalization (NH2 and sw-NH2) showed intermediary effects. In contrast, the strongly cationic PEI-functionalized tubes induced robust biological effects. These differences could be attributed to differences in cellular uptake and NLRP3 inflammasome activation, which depends on the propensity toward lysosomal damage and cathepsin B release in macrophages. Moreover, the in vitro hazard ranking was validated by the pro-fibrogenic potential of the tubes in vivo. Compared to pristine MWCNTs, strong cationic PEI-MWCNTs induced significant lung fibrosis, while carboxylation significantly decreased the extent of pulmonary fibrosis. These results demonstrate that surface charge plays an important role in the structure-activity relationships that determine the pro-fibrogenic potential of f-CNTs in the lung.

Differentiation of complex vapor mixtures using versatile DNA-carbon nanotube chemical sensor arrays

Vapor sensors based on functionalized carbon nanotubes (NTs) have shown great promise, with high sensitivity conferred by the reduced dimensionality and exceptional electronic properties of the NT. Critical challenges in the development of NT-based sensor arrays for chemical detection include the demonstration of reproducible fabrication methods and functionalization schemes that provide high chemical diversity to the resulting sensors. Here, we outline a scalable approach to fabricating arrays of vapor sensors consisting of NT field effect transistors functionalized with single-stranded DNA (DNA-NT). DNA-NT sensors were highly reproducible, with responses that could be described through equilibrium thermodynamics. Target analytes were detected even in large backgrounds of volatile interferents. DNA-NT sensors were able to discriminate between highly similar molecules, including structural isomers and enantiomers. The sensors were also able to detect subtle variations in complex vapors, including mixtures of structural isomers and mixtures of many volatile organic compounds characteristic of humans.

Addressing reliability and degradation of chemitransistor sensors by electrical tuning of the sensitivity

Here we show that electrical tuning of the sensitivity of chemitransistor sensors, namely field-effect-transistors (FETs) exploiting nano/mesostructured sensing materials, can be used to effectively address two chief problems of state-of-the-art gas sensors, specifically fabrication reliability and degradation by aging. Both experimental evidences and theoretical calculations are provided to support such a result, using as a case-of-study junction field-effect-transistors (JFETs) exploiting mesostructured porous silicon (PS) as sensing material (PSJFETs) for the detection of nitrogen dioxide (NO(2)) at hundreds ppb. Proof of concept is given by fully compensating the effect of fabrication errors on the sensitivity of two PSJFETs integrated on the same chip, which, though identical in principle, feature sensitivities to NO(2) differing from about 30% before compensation. Although here-demonstrated for the specific case of PSJFETs, the concept of sensor reliability/aging problem compensation by sensitivity electrical-tuning can be applied to other chemitransistor sensors that exploit sensing materials different than PS.

Detection of a CO and NH3 gas mixture using carboxylic acid-functionalized single-walled carbon nanotubes

Carbon nanotubes (CNT) are extremely sensitive to environmental gases. However, detection of mixture gas is still a challenge. Here, we report that 10 ppm of carbon monoxide (CO) and ammonia (NH3) can be electrically detected using a carboxylic acid-functionalized single-walled carbon nanotubes (C-SWCNT). CO and NH3 gases were mixed carefully with the same concentrations of 10 ppm. Our sensor showed faster response to the CO gas than the NH3 gas. The sensing properties and effect of carboxylic acid group were demonstrated, and C-SWCNT sensors with good repeatability and fast responses over a range of concentrations may be used as a simple and effective detection method of CO and NH3 mixture gas.

Understanding Interfaces in Metal-Graphitic Hybrid Nanostructures

Metal-graphitic interfaces formed between metal nanoparticles (MNPs) and carbon nanotubes (CNTs) or graphene play an important role in the properties of such hybrid nanostructures. This Perspective summarizes different types of interfaces that exist within the metal-carbon nanoassemblies and discusses current efforts on understanding and modeling the interfacial conditions and interactions. Characterization of the metal-graphitic interfaces is described here, including microscopy, spectroscopy, electrochemical techniques, and electrical measurements. Recent studies on these nanohybrids have shown that the metal-graphitic interfaces play critical roles in both controlled assembly of nanoparticles and practical applications of nanohybrids in chemical sensors and fuel cells. Better understanding, design, and manipulation of metal-graphitic interfaces could therefore become the new frontier in the research of MNP/CNT or MNP/graphene hybrid systems.

Effect of antioxidants on enzyme-catalysed biodegradation of carbon nanotubes

The growing applications of carbon nanotubes (CNTs) inevitably increase the risk of exposure to this potentially toxic nanomaterial. In an attempt to address this issue, research has been implemented to study the biodegradation of CNTs. In particular, myeloperoxidase (MPO), an enzyme expressed by inflammatory cells of animals including humans, catalyse the degradation of oxidized carbon nanomaterials. While reactive intermediates generated by MPO efficiently degrade oxidized single-walled carbon nanotubes (o-SWCNTs); the exact mechanism of enzyme-catalysed biodegradation remains ambiguous. In this work, we tried to explain enzymatic oxidation in terms of redox potentials by employing competitive substrates for MPO such as chloride, which is oxidized by MPO to form a strong oxidant (hypochlorite), and antioxidants that have lower redox potentials than CNTs. Employing transmission electron microscopy, Raman spectroscopy, and vis-NIR absorption spectroscopy, we demonstrate that the addition of antioxidants, L-ascorbic acid and L-glutathione, with or without chloride significantly mitigates MPO-catalysed biodegradation of o-SWCNTs. This study focuses on a fundamental understanding of the mechanisms of enzymatic biodegradation of CNTs and the impact of antioxidants on these pathways.

Highly enhanced gas sensing in single-walled carbon nanotube-based thin-film transistor sensors by ultraviolet light irradiation

Single-walled carbon nanotube (SWCNT) random networks are easily fabricated on a wafer scale, which provides an attractive path to large-scale SWCNT-based thin-film transistor (TFT) manufacturing. However, the mixture of semiconducting SWCNTs and metallic SWCNTs (m-SWCNTs) in the networks significantly limits the TFT performance due to the m-SWCNTs dominating the charge transport. In this paper, we have achieved a uniform and high-density SWCNT network throughout a complete 3-in. Si/SiO2 wafer using a solution-based assembly method. We further utilized UV radiation to etch m-SWCNTs from the networks, and a remarkable increase in the channel current on/off ratio (Ion/Ioff) from 11 to 5.6 × 103 was observed. Furthermore, we used the SWCNT-TFTs as gas sensors to detect methyl methylphosphonate, a stimulant of benchmark threats. It was found that the SWCNT-TFT sensors treated with UV radiation show a much higher sensitivity and faster response to the analytes than those without treatment with UV radiation.

Porphyrins-Functionalized Single-Walled Carbon Nanotubes Chemiresistive Sensor Arrays for VOCs

Single-walled carbon nanotubes (SWNTs) have been used extensively for sensor fabrication due to its high surface to volume ratio, nanosized structure and interesting electronic property. Lack of selectivity is a major limitation for SWNTs-based sensors. However, surface modification of SWNTs with a suitable molecular recognition system can enhance the sensitivity. On the other hand, porphyrins have been widely investigated as functional materials for chemical sensor fabrication due to their several unique and interesting physico-chemical properties. Structural differences between free-base and metal substituted porphyrins make them suitable for improving selectivity of sensors. However, their poor conductivity is an impediment in fabrication of prophyrin-based chemiresistor sensors. The present attempt is to resolve these issues by combining freebase- and metallo-porphyrins with SWNTs to fabricate SWNTs-porphyrin hybrid chemiresistor sensor arrays for monitoring volatile organic carbons (VOCs) in air. Differences in sensing performance were noticed for porphyrin with different functional group and with different central metal atom. The mechanistic study for acetone sensing was done using field-effect transistor (FET) measurements and revealed that the sensing mechanism of ruthenium octaethyl porphyrin hybrid device was governed by electrostatic gating effect, whereas iron tetraphenyl porphyrin hybrid device was governed by electrostatic gating and Schottky barrier modulation in combination. Further, the recorded electronic responses for all hybrid sensors were analyzed using a pattern-recognition analysis tool. The pattern-recognition analysis confirmed a definite pattern in response for different hybrid material and could efficiently differentiate analytes from one another. This discriminating capability of the hybrid nanosensor devices open up the possibilities for further development of highly dense nanosensor array with suitable porphyrin for E-nose application.

Corking carbon nanotube cups with gold nanoparticles

Nitrogen doping of carbon nanotubes during chemical vapor deposition synthesis can create unique stacked cup-shaped structures termed as nitrogen-doped carbon nanotube cups (NCNCs). These cups have semielliptical hollow cavities and elevated reactivity which could lead to various applications. In this work, by applying intense ultrasonication to the as-synthesized NCNCs, we demonstrated an effective mechanical method to isolate the individual cups with opened cavities from their stacks. The graphitic structures of the isolated cups and their inherent nitrogen functionalities were characterized by comprehensive microscopic and spectroscopic methods. In particular, we quantitatively determined the existence of amine functionalities on NCNCs and found that they were preferentially distributed at the open edges of the cups, providing localized reactive sites. Further, by thiolating the amine groups with 3-mercapto-propionic acid, we were able to effectively cork the isolated cups by gold nanoparticles with commensurate diameters. These cup-shaped carbon nanomaterials with controlled inner volumes and gold nanoparticle corks could find potential applications as nanoscale reaction containers or drug delivery vehicles.

Modulating gas sensing properties of CuO nanowires through creation of discrete nanosized p-n junctions on their surfaces

We report significant enhancement of CuO nanowire (NW) sensing performance at room temperature through the surface functionalization with SnO(2) nanocrystals (NCs). The sensitivity enhancement can be as high as ∼300% for detecting 1% NH(3) diluted in air. The improved sensitivity could be attributed to the electronic interaction between p-type CuO NWs and n-type SnO(2) NCs due to the formation of nanosized p-n junctions, which are highly sensitive to the surrounding gaseous environment and could effectively manipulate local charge carrier concentration. Our results suggest that the NC-NW structure is an attractive candidate for practical sensing applications, in view of its outstanding room-temperature sensitivity, excellent dynamic properties (rapid response and quick recovery), and flexibility in modulating the sensing performance (e.g., by adjusting the coverage of SnO(2) NCs on CuO NWs and doping of SnO(2) NCs).

Observation of room-temperature negative differential resistance in Gd-doped Si nanowires on Si(110) surface

The massively parallel arrays of highly periodic Gd-doped Si nanowires (SiNWs) self-organized on Si(110)-16 × 2 surface were investigated by scanning tunneling microscopy and spectroscopy. These periodic Gd-doped SiNWs are atomically precise and show equal size, periodic positions, and high-integration densities. Surprisingly, the scanning tunneling spectroscopy results show that each metallic-like, Gd-doped SiNW exhibits room-temperature negative differential resistance (RT-NDR) behavior, which can be reproducible with various Gd dopings and is independent of the tips. Such massively parallel arrays of highly ordered and atomically identical Gd-doped SiNWs with one-dimensional laterally confined RT-NDR can be exploited in Si-based RT-NDR nanodevices.

Synthesis of nanograined ZnO nanowires and their enhanced gas sensing properties

Polycrystalline ZnO nanowires with grain sizes ranging from 20 to 100 nm were synthesized using a newly designed two-step process: (first step) synthesis of ZnSe nanowires by vapor transportation of a mixture of ZnSe powders; and (second step) thermal oxidation of the ZnSe nanowires at 650 °C. Compared to the single-crystal ZnO nanowire gas sensors and other nanomaterial gas sensors reported previously, the multiple networked nanowire gas sensors fabricated from the nanograined ZnO nanowires showed substantially enhanced electrical responses to NO2 gas at 300 °C. The NO2 gas sensing properties of the nanograined ZnO nanowires increased dramatically with increasing NO2 concentration. The multiple-networked nanograined ZnO nanowire sensor showed a response value of 237,263% at 10 ppm NO2 and 300 °C, whereas the single-crystal ZnO nanowire sensors showed a response of only 6.5% under the same conditions. The recovery time of the nanograined ZnO nanowire sensor was much shorter than that of the normal ZnO nanowire sensor over the NO2 concentration range of 1-10 ppm, even though the response time of the former was somewhat longer than that of the latter. The origin of the enhanced NO2 gas sensing properties of the nanograined ZnO nanowire sensor is discussed.

CVD-grown horizontally aligned single-walled carbon nanotubes: synthesis routes and growth mechanisms

Single-walled carbon nanotubes (SWCNTs) have attractive electrical and physical properties, which make them very promising for use in various applications. For some applications however, in particular those involving electronics, SWCNTs need to be synthesized with a high degree of control with respect to yield, length, alignment, diameter, and chirality. With this in mind, a great deal of effort is being directed to the precision control of vertically and horizontally aligned nanotubes. In this review the focus is on the latter, horizontally aligned tubes grown by chemical vapor deposition (CVD). The reader is provided with an in-depth review of the established vapor deposition orientation techniques. Detailed discussions on the characterization routes, growth parameters, and growth mechanisms are also provided.

High-damping carbon nanotube hinged micromirrors

New developments in digital mirror devices (DMDs) require suspension hinges with a good damping and high temperature stability. Carbon nanotubes (CNTs) offer these unique properties. Herein it is shown how CNT hinges can be integrated in micromirrors. The image illustrates a micromirror with a CNT suspension, and a typical overdamped stepresponse (Q-factor < 0.5).

Multidimensional conducting polymer nanotubes for ultrasensitive chemical nerve agent sensing

Tailoring the morphology of materials in the nanometer regime is vital to realizing enhanced device performance. Here, we demonstrate flexible nerve agent sensors, based on hydroxylated poly(3,4-ethylenedioxythiophene) (PEDOT) nanotubes (HPNTs) with surface substructures such as nanonodules (NNs) and nanorods (NRs). The surface substructures can be grown on a nanofiber surface by controlling critical synthetic conditions during vapor deposition polymerization (VDP) on the polymer nanotemplate, leading to the formation of multidimensional conducting polymer nanostructures. Hydroxyl groups are found to interact with the nerve agents. Representatively, the sensing response of dimethyl methylphosphonate (DMMP) as a simulant for sarin is highly sensitive and reversible from the aligned nanotubes. The minimum detection limit is as low as 10 ppt. Additionally, the sensor had excellent mechanical bendability and durability.

Ultrasensitive chemical detection using a nanocoax sensor

We report on the design, fabrication, and performance of a nanoporous, coaxial array capacitive detector for highly sensitive chemical detection. Composed of an array of vertically aligned nanoscale coaxial electrodes constructed with porous dielectric coax annuli around carbon nanotube cores, this sensor is shown to achieve parts per billion level detection sensitivity, at room temperature, to a broad class of organic molecules. The nanoscale, 3D architecture and microscale array pitch of the sensor enable rapid access of target molecules and chip-based multiplexing capabilities, respectively.