Ionic-Liquid-Based Polymer Electrolytes for Battery Applications

Modifying potato starch by glutaraldehyde and MgCl2 for developing an economical and environment-friendly electrolyte system

Biodegradable polymer electrolyte systems are the most sought over option for cheap and energy efficient storage devices. Present paper discusses the results of potato starch + MgCl2 system which satisfy the technical and economic criteria to become a potential candidate for future electrolyte systems. The developed system has high ionic conductivity (~3.43 × 10-2 S/cm), low relaxation time (75 μs) and wide electrochemical stability window (ESW ~4.6 V). The phase angle approaches -79° and maintains its value for 10 Hz to 1 kHz frequency range. The prepared material is a free standing film which can be bended and twisted up to 90°, which makes it suitable for flexible electrochemical device fabrication. The equivalent series resistance (ESR) is quite low (3.41 Ω) and self-resonance frequency below which energy can be efficiently stored is approximately 0.1 MHz. Hence the present study reports an economical, easy to handle and environment friendly electrolyte suitable for electrochemical device fabrication.

Electrochemical Impedance Spectroscopy and X-ray Photoelectron Spectroscopy Study of Lithium Metal Surface Aging in Imidazolium-Based Ionic Liquid Electrolytes Performed at Open-Circuit Voltage

Lithium reactivity toward an electrolytic media and dendrite growth phenomenon constitutes the main drawback for its use as an anode material for the lithium battery technology. Ionic liquids (ILs) were pointed out as promising electrolyte solvent candidates to prevent thermal runaway in a lithium battery system. However, the reactivity of lithium toward such a kind of an electrolyte is still under debate. In this study, the interaction between lithium metal and imidazolium-based ILs, 1-hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (C₁C₆ImTFSI) and 1-hexyl-3-methylimidazolium bis(fluorosulfonyl)imide (C₁C₆ImFSI), has been investigated based on the nondestructive methodology coupling electrochemical impedance spectroscopy (EIS) and X-ray photoelectron spectroscopy (XPS) in coin cells aged several days at open-circuit voltage. The main components detected by XPS in the bulk separator and at the surface of the lithium metal are the byproducts of cation and anion degradation. Similarities and differences were noticed depending on the anion nature of bis(trifluoromethylsulfonyl)imide versus bis(fluorosulfonyl)imide. The role of lithium salt addition (LiTFSI) was also pointed, giving rise to the stability improvement of the electrolytic solution toward the lithium anode. A direct correlation between the resistance of the bulk electrolyte and of the interface electrolyte/lithium and chemical composition changes were established based on a detailed EIS and XPS combined study.

The Dependence of Ionic Liquid Solvent Effects on the Nucleophilic Heteroatom in SN Ar Reactions. Highlighting the Potential for Control of Selectivity

Nucleophilic aromatic substitution (S_N Ar) reactions of 1-fluoro-4-nitrobenzene using similar nitrogen and sulfur nucleophiles were studied through extensive kinetic analysis in mixtures containing ionic liquids. The interactions of the ionic liquid components with the starting materials and transition state for each process were investigated in an attempt to construct a broad predictive framework for how ionic liquids affect reaction outcome. It was found that, based on the activation parameters, the microscopic interactions and thus the ionic liquid solvent effect were different for each of the nucleophiles considered. The results from this study suggest that it may be possible to rationally select a given ionic liquid mixture to selectively control reaction outcome of an S_N Ar reaction where multiple nucleophiles are present.

Gel/Solid Polymer Electrolytes Characterized by In Situ Gelation or Polymerization for Electrochemical Energy Systems

A gel polymer electrolyte (GPE) is a liquid electrolyte (LE) entrapped by a small amount of polymer network less than several wt%, which is characterized by properties between those of liquid and solid electrolytes in terms of the ionic conductivity and physical phase. Electrolyte leakage and flammability, demerits of liquid electrolytes, can be mitigated by using GPEs in electrochemical cells. However, the contact problems between GPEs and porous electrodes are challenging because it is difficult to incorporate GPEs into the pores and voids of electrodes. Herein, the focus is on GPEs that are gelated in situ within cells instead of covering comprehensive studies of GPEs. A mixture of LE and monomer or polymer in a liquid phase is introduced into a pre-assembled cell without electrolyte, followed by thermal gelation based on physical gelation, monomer polymerization, or polymer cross-linking. Therefore, GPEs are formed omnipresent in cells, covering the pores of electrode material particles, and even the pores of separators. As a result, different from ex situ formed GPEs, the in situ GPEs have no electrode/electrolyte contact problems. Functional GPEs are introduced as a more advanced form of GPEs, improving lithium-ion transference number or capturing transition metals released from electrode materials.

A Cross-Linker-Based Poly(Ionic Liquid) for Sensitive Electrochemical Detection of 4-Nonylphenol

In this study, we report a cross-linker-based poly(ionic liquid) (PIL) for the sensitive detection of 4-nonylphenol (4-NP). PIL was poly(1,4-butanediyl-3,3′-bis-l-vinylimidazolium dibromide) (poly([V₂C₄(mim)₂]Br₂)). Poly([V₂C₄(mim)₂]Br₂) was prepared via one-step free-radical polymerization. The poly([V₂C₄(mim)₂]Br₂) was characterized by infrared spectroscopy, Raman spectroscopy, thermal gravimetric analyzer and scanning electron microscope. The poly([V₂C₄(mim)₂]Br₂) was then drop-cast onto a glassy carbon electrode (GCE) to obtain poly([V₂C₄(mim)₂]Br₂)/GCE. In comparison with a bare GCE, poly([V₂C₄(mim)₂]Br₂)/GCE exhibited higher peak current responses for [Fe(CN)₆]^3−/4−, lower charge transfer resistance, and larger effective surface area. While comparing the peak current responses, we found the peak current response for 4-NP using poly([V₂C₄(mim)₂]Br₂)/GCE to be 3.6 times higher than a traditional cross-linker ethylene glycol dimethacrylate (EGDMA) based poly(EGDMA) modified GCE. The peak current of poly([V₂C₄(mim)₂]Br₂) sensor was linear to 4-NP concentration from 0.05 to 5 μM. The detection limit of 4-NP was obtained as 0.01 μM (S/N = 3). The new PIL based electrochemical sensor also exhibited excellent selectivity, stability, and reusability. Furthermore, the poly([V₂C₄(mim)₂]Br₂)/GCE demonstrated good 4-NP detection in environmental water samples.

Novel Chemical Cross-Linked Ionogel Based on Acrylate Terminated Hyperbranched Polymer with Superior Ionic Conductivity for High Performance Lithium-Ion Batteries

A new family of chemical cross-linked ionogel is successfully synthesized by photopolymerization of hyperbranched aliphatic polyester with acrylate terminal groups in an ionic liquid of 1-butyl-3-methylimidazolium tetrafluoroborate (BMIMBF₄). The microstructure, viscoelastic behavior, mechanical property thermal stability, and ionic conductivities of the ionogels are investigated systematically. The ionogels exhibit high mechanical strength (up to 1.6 MPa) and high mechanical stability even at temperatures up to 200 °C. It is found to be thermally stable up to 371.3 °C and electrochemically stable above 4.3 V. The obtained ionogels show superior ionic conductivity over a wide temperature range (from 1.2 × 10^-3 S cm^-1 at 20 °C up to 5.0 × 10^-2 S cm^-1 at 120 °C). Moreover, the Li/LiFePO₄ batteries based on ionogel electrolyte with LiBF₄ show a higher specific capacity of 153.1 mAhg^-1 and retain 98.1% after 100 cycles, exhibiting very stable charge/discharge behavior with good cycle performance. This work provides a new method for fabrication of novel advanced gel polymer electrolytes for applications in lithium-ion batteries.

Charge transport and glassy dynamics in polymeric ionic liquids as reflected by their inter- and intramolecular interactions

Polymeric ionic liquids (PILs) form a novel class of materials in which the extraordinary properties of ionic liquids (ILs) are combined with the mechanical stability of polymeric systems qualifying them for multifold applications. In the present study broadband dielectric spectroscopy (BDS), Fourier transform infrared spectroscopy (FTIR), AC-chip calorimetry (ACC) and differential scanning calorimetry (DSC) are combined in order to unravel the interplay between charge transport and glassy dynamics. Three low molecular weight ILs and their polymeric correspondents are studied with systematic variations of anions and cations. For all examined samples charge transport takes place by glassy dynamics assisted hopping conduction. In contrast to low molecular weight ILs the thermal activation of DC conductivity for the polymeric systems changes from a Vogel-Fulcher-Tammann- to an Arrhenius-dependence at a (sample specific) temperature Tσ0. This temperature has been widely discussed to coincide with the glass transition temperature Tg, a refined analysis, instead, reveals Tσ0 of all PILs under study at up to 80 K higher values. In effect, below the Tσ0 charge transport in PILs becomes more efficient - albeit on a much lower level compared to the low molecular weight pendants - indicating conduction paths along the polymer chain. This is corroborated by analysing the temperature dependence of specific IR-active vibrations showing at Tσ0 distinct changes in the spectral position and the oscillator strength, whereas other molecular units are not affected. This leads to the identification of charge transport responsive (CTR) as well as charge transport irresponsive (CTI) moieties and paves the way to a refined molecular understanding of electrical conduction in PILs.

Bio-Integrated Wearable Systems: A Comprehensive Review

Bio-integrated wearable systems can measure a broad range of biophysical, biochemical, and environmental signals to provide critical insights into overall health status and to quantify human performance. Recent advances in material science, chemical analysis techniques, device designs, and assembly methods form the foundations for a uniquely differentiated type of wearable technology, characterized by noninvasive, intimate integration with the soft, curved, time-dynamic surfaces of the body. This review summarizes the latest advances in this emerging field of "bio-integrated" technologies in a comprehensive manner that connects fundamental developments in chemistry, material science, and engineering with sensing technologies that have the potential for widespread deployment and societal benefit in human health care. An introduction to the chemistries and materials for the active components of these systems contextualizes essential design considerations for sensors and associated platforms that appear in following sections. The subsequent content highlights the most advanced biosensors, classified according to their ability to capture biophysical, biochemical, and environmental information. Additional sections feature schemes for electrically powering these sensors and strategies for achieving fully integrated, wireless systems. The review concludes with an overview of key remaining challenges and a summary of opportunities where advances in materials chemistry will be critically important for continued progress.

Structural correlations tailor conductive properties in polymerized ionic liquids

In this paper, it was demonstrated that the mobile ion (anion) size and pendant group chemistry affect the packing of the polymer chains and influence conductivity in imidazolium based PolyILs.

Self-assembly of highly asymmetric, poly(ionic liquid)-rich diblock copolymers and the effects of simple structural modification on phase behaviour

A series of ATRP-synthesized poly(IL) diblock copolymers exhibit morphological phase behavior with shifted phase boundaries and alkyl substituent dependent segregation.

Free ion diffusivity and charge concentration on cross-linked polymeric ionic liquid iongel films based on sulfonated zwitterionic salts and lithium ions

The properties of various mixtures of a zwitterionic ionic liquid (ZIs-1) and LiNTf2, including their conductivity, have been studied showing how they can be adjusted through their molar composition. Conductivity tends to increase with the LiNTf2 content although it presents a minimum at the region close to the eutectic point. These mixtures also provide excellent features as liquid phases for the preparation of composite materials based on crosslinked PILs. The prepared films display excellent and tuneable properties as conducting materials, with conductivities that can be higher than 10-2 S cm-1 above 100 °C. The selected polymeric compositions show very good mechanical properties and thermal stability, even for low crosslinking degrees, along with a suitable flexibility and good transparency. The final properties of the films correlate with the composition of the monomeric mixture used and with that of the ZIs-1:LiNTf2 mixture.

Electrochemical behaviors of Li-argyrodite-based all-solid-state batteries under deep-freezing conditions

We probe the electrochemical performance of Li-argyrodite-based all-solid-state batteries under deep-freezing conditions (-30 °C) using electrochemical impedance spectroscopy. The performance deterioration is mainly caused by the increased interfacial resistances of electrolyte and active materials resulting from the slow kinetics of Li-ion transport in solid materials at low temperatures.

Hybrid Solid Polymer Electrolytes with Two-Dimensional Inorganic Nanofillers

Solid polymer electrolytes are of rapidly increasing importance for the research and development of future safe batteries with high energy density. The diversified chemistry and structures of polymers allow the utilization of a wide range of soft structures for all-polymer solid-state electrolytes. With equal importance is the hybrid solid-state electrolytes consisting of both "soft" polymeric structure and "hard" inorganic nanofillers. The recent emergence of the re-discovery of many two-dimensional layered materials has stimulated the booming of advanced research in energy storage fields, such as batteries, supercapacitors, and fuel cells. Of special interest is the mass transport properties of these 2D nanostructures for water, gas, or ions. This review aims at the current progress and prospective development of hybrid polymer-inorganic solid electrolytes based on important 2D materials, including natural clay and synthetic lamellar structures. The ion conduction mechanism and the fabrication, property and device performance of these hybrid solid electrolytes will be discussed.

From Nature to Energy Storage: A Novel Sustainable 3D Cross-Linked Chitosan-PEGGE-Based Gel Polymer Electrolyte with Excellent Lithium-Ion Transport Properties for Lithium Batteries

Developing a gel polymer electrolyte with a cross-linked structure is one of the best choices to improve the mechanical strength of the gel polymer electrolyte without sacrificing its lithium-ion transportation properties. However, the cost is always too high. Herein, a novel gel polymer electrolyte based on three-dimensional cross-linked chitosan-poly(ethylene glycol) diglycidyl ether macromolecule network was designed and synthesized through a simple and environmental harmless method, with sustainable and cheap chitosan as major material. The obtained gel polymer electrolyte shows improved mechanical strength of 5.5 MPa, which is higher than that of other gel polymer electrolytes without inert frameworks. The optimized gel polymer electrolyte exhibits a good lithium ionic conductivity of 2.74 × 10^-4 S cm^-1 with a superior lithium-ion transfer number of 0.869 at 25 °C. Lithium battery assembled with this gel polymer electrolyte demonstrates an initial discharge capacity of 146.8 mA h g^-1, which retains 88.49% capacity after 360 cycles at 0.2C. Moreover, this gel polymer electrolyte possesses good interfacial compatibility with lithium anode. Therefore, the growth of lithium dendrite is greatly delayed. This research proves the great possibility of applying sustainable and cost-effective chitosan into gel polymer electrolyte and lithium batteries.

Ion Gel Network Formation in an Ionic Liquid Studied by Time-Resolved Small-Angle Neutron Scattering

We report the time-resolved small-angle neutron scattering (SANS) study of tetra-arm poly(ethylene glycol) (TetraPEG) polymer network formation in a typical ionic liquid (IL), 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)amide ([C₂mim][TFSA]). To observe time-dependent SANS profiles, the reaction rate for the AB-type cross-end coupling reaction of TetraPEG macromers was controlled by adding an analogous protic IL, 1-ethylimidazolium TFSA ([C₂imH][TFSA]). At polymer concentrations higher than the overlap concentration ( c*), the SANS profile remained unchanged during the gelation reaction, indicating that the network structure was independent of macromer connectivity in a semidiluted solution. On the other hand, at low polymer concentrations, an increase in the SANS profile intensity was clearly observed. The correlation length (ξ), estimated by a fitting analysis based on the Ornstein-Zernike function, increased as the reaction proceeded. This result indicated that the sparsely dispersed macromers formed clusters during the cross-linking process and polymer size growth followed thereafter. We found that the network formation process and homogeneity of the network structure were strongly dependent on the polymer concentration in IL solutions.

Elevated-Temperature 3D Printing of Hybrid Solid-State Electrolyte for Li-Ion Batteries

While 3D printing of rechargeable batteries has received immense interest in advancing the next generation of 3D energy storage devices, challenges with the 3D printing of electrolytes still remain. Additional processing steps such as solvent evaporation were required for earlier studies of electrolyte fabrication, which hindered the simultaneous production of electrode and electrolyte in an all-3D-printed battery. Here, a novel method is demonstrated to fabricate hybrid solid-state electrolytes using an elevated-temperature direct ink writing technique without any additional processing steps. The hybrid solid-state electrolyte consists of solid poly(vinylidene fluoride-hexafluoropropylene) matrices and a Li⁺ -conducting ionic-liquid electrolyte. The ink is modified by adding nanosized ceramic fillers to achieve the desired rheological properties. The ionic conductivity of the inks is 0.78  × 10 ^-3 S cm^-1 . Interestingly, a continuous, thin, and dense layer is discovered to form between the porous electrolyte layer and the electrode, which effectively reduces the interfacial resistance of the solid-state battery. Compared to the traditional methods of solid-state battery assembly, the directly printed electrolyte helps to achieve higher capacities and a better rate performance. The direct fabrication of electrolyte from printable inks at an elevated temperature will shed new light on the design of all-3D-printed batteries for next-generation electronic devices.

High Performance Polymer/Ionic Liquid Thermoplastic Solid Electrolyte Prepared by Solvent Free Processing for Solid State Lithium Metal Batteries

A polymer/ionic liquid thermoplastic solid electrolyte based on poly(ethylene oxide) (PEO), modified sepiolite (TPGS-S), lithium bis(trifluoromethanesulfonyl)imide (LiTFSI), and 1-Butyl-1-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide (PYR14TFSI) ionic liquid is prepared using solvent free extrusion method. Its physical-chemical, electrical, and electrochemical properties are comprehensively studied. The investigated solid electrolyte demonstrates high ionic conductivity together with excellent compatibility with lithium metal electrode. Finally, truly Li-LiFePO₄ solid state coin cell with the developed thermoplastic solid electrolyte demonstrates promising electrochemical performance during cycling under 0.2 C/0.5 C protocol at 60 °C.

A Water Dissolvable Electrolyte with an Ionic Liquid for Eco-Friendly Electronics

A water-dissolvable electrolyte is developed by combining an ionic liquid (IL) with poly(vinyl alcohol) (PVA), which decays over time by contact with water. An IL generally consists of two species of ions (anion and cation), and forms an electrical double layer (EDL) of a large electrostatic capacitance due to the ions accumulated in the vicinity of a conductive electrode when voltage is applied. In a similar manner, the ionic gel developed in this work forms an EDL due to the ions suspended in the conjugated polymer network while maintaining the gel form. Test measurements show a large capacitance of 13 µF cm^-2 within the potential window of the IL. The ionic gel shows an electrical conductance of 20 µS cm^-1 due to the ionic conduction, which depends on the weight ratio of the IL with respect to the polymer. The developed ionic gel dissolves into water in 16 h. Potential application includes the electrolyte in disposable electronics such as distributed sensors and energy harvesters that are supposed to be harmless to environment.

Selective separation of cadmium(ii) from zinc(ii) by a novel hydrophobic ionic liquid including an N,N,N',N'-tetrakis(2-methylpyridyl)-1,2-phenylenediamine-4-amido structure: a hard-soft donor combined method

A novel hydrophobic ionic liquid including an N,N,N',N'-tetrakis(2-methylpyridyl)-1,2-phenylenediamine-4-amido structure ((IL-1,2-tpbd)+NTf2-) was successfully synthesized. (IL-1,2-tpbd)+NTf2- combined one amido (O-hard donor) and four pyridine (N-soft donor) groups. Its Cd2+ and Zn2+ separation behavior in nitric acid solution was investigated as a function of the extraction time, effect of pH etc. by dissolving (IL-1,2-tpbd)+NTf2- in a room temperature ionic liquid, 1-hexyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ((C6mim)+NTf2-). The extraction kinetics were fairly fast and could reach equilibrium within 4 h. When pHeq ≥ 1.8, the extraction percentage of Cd2+ and Zn2+ remained constant and the maximum separation factor was calculated as 12.78 at pHeq = 3.1; when pHeq < 1.8, the extraction percentage of Cd2+ and Zn2+ decreased drastically due to the protonation of the pyridine groups. Complete stripping of the extracted Cd2+ and Zn2+ from the ionic liquid phase into an aqueous phase was successfully achieved under highly acidic conditions ([HNO3] = 2 M) without adding any other metal complex forming agents. The extraction mechanism was summarized as a cation exchange due to the independence of nitrate ions in the extraction process. Additionally, the results of the slope analysis and UV-vis titration revealed the formation of a 1 : 2 complex. Furthermore, (IL-1,2-tpbd)+NTf2- showed a higher preference for Cd2+ even under the interference of various co-existing metal ions.

Effective Suppression of Lithium Dendrite Growth Using a Flexible Single-Ion Conducting Polymer Electrolyte

A novel single-ion conducting polymer electrolyte (SIPE) membrane with high lithium-ion transference number, good mechanical strength, and excellent ionic conductivity is designed and synthesized by facile coupling of lithium bis(allylmalonato) borate (LiBAMB), pentaerythritol tetrakis (2-mercaptoacetate) (PETMP) and 3,6-dioxa-1,8-octanedithiol (DODT) in an electrospun poly(vinylidienefluoride) (PVDF) supporting membrane via a one-step photoinitiated in situ thiol-ene click reaction. The structure-optimized LiBAMB-PETMP-DODT (LPD)@PVDF SIPE shows an outstanding ionic conductivity of 1.32 × 10-3 S cm-1 at 25 °C, together with a high lithium-ion transference number of 0.92 and wide electrochemical window up to 6.0 V. The SIPE exhibits high tensile strength of 7.2 MPa and elongation at break of 269%. Due to these superior performances, the SIPE can suppress lithium dendrite growth, which is confirmed by galvanostatic Li plating/stripping cycling test and analysis of morphology of Li metal electrode surface after cycling test. Li|LPD@PVDF|Li symmetric cell maintains an extremely stable and low overpotential without short circuiting over the 1050 h cycle. The Li|LPD@PVDF|LiFePO4 cell shows excellent rate capacity and outstanding cycle performance compared to cells based on a conventional liquid electrolyte (LE) with Celgard separator. The facile approach of the SIPE provides an effective and promising electrolyte for safe, long-life, and high-rate lithium metal batteries.

Ionic Gels and Their Applications in Stretchable Electronics

Ionic gels represent a novel class of stretchable materials where ionic conducting liquid is immobilized in a polymer matrix. This review focuses on the design of ionic gel materials and device fabrication of ionic-gel-based stretchable electronics. In particular, recent progress in ionic-gel-based electronic skin (pressure/strain sensors, electric double-layer transistors, etc.), flexible displays, energy storage devices, and soft actuators are summarized, followed by a discussion of challenges in developing ionic-gel-based electronics and suggestions for future research directions that might overcome those challenges.

Glyoxal-Based Solvents for Electrochemical Energy-Storage Devices

In this work an investigation about the use of the solvents 1,1,2,2-tetramethoxyethane, also called tetramethoxy glyoxal (TMG), and 1,1,2,2-tetraethoxyethane [also called tetraethoxy glyoxal (TEG)], which belong to the chemical family of carbonyl derivatives, as electrolyte components for electrical double layer capacitors (EDLCs) and lithium-ion batteries (LIBs) is reported for the first time. TEG and TMG are commercial solvents displaying a good set of properties, a low toxicity, and a low price. Although for EDLCs the use of these solvents does appear particularly appealing, their use in LIBs is certainly interesting. The preliminary results reported in this study indicate that the performance of lithium iron phosphate electrodes in LIBs using electrolytes based on TEG and TMG is promising in terms of capacity, capacity retention at high C rates, and cycling stability.