Multifunctional nanostructured PLA materials for packaging and tissue engineering

Surface Hydrophilicity of Poly(l-Lactide) Acid Polymer Film Changes the Human Adult Adipose Stem Cell Architecture

Current knowledge indicates that the molecular cross-talk between stem cells and biomaterials guides the stem cells’ fate within a tissue engineering system. In this work, we have explored the effects of the interaction between the poly(l-lactide) acid (PLLA) polymer film and human adult adipose stem cells (hASCs), focusing on the events correlating the materials’ surface characteristics and the cells’ plasma membrane. hASCs were seeded on films of pristine PLLA polymer and on a PLLA surface modified by the radiofrequency plasma method under oxygen flow (PLLA+O₂). Comparative experiments were performed using human bone-marrow mesenchymal stem cells (hBM-MSCs) and human umbilical matrix stem cells (hUCMSCs). After treatment with oxygen-plasma, the surface of PLLA films became hydrophilic, whereas the bulk properties were not affected. hASCs cultured on pristine PLLA polymer films acquired a spheroid conformation. On the contrary, hASCs seeded on PLLA+O₂ film surface maintained the fibroblast-like morphology typically observed on tissue culture polystyrene. This suggests that the surface hydrophilicity is involved in the acquisition of the spheroid conformation. Noteworthy, the oxygen treatment had no effects on hBM-MSC and hUCMSC cultures and both stem cells maintained the same shape observed on PLLA films. This different behavior suggests that the biomaterial-interaction is stem cell specific.

Introduction of stereocomplex crystallites of PLA for the solid and microcellular poly(lactide)/poly(butylene adipate-co-terephthalate) blends

Solid and microcellular poly(l-lactide)/poly(butylene adipate-co-terephthalate) (PLLA/PBAT) blends with or without poly(d-lactide) (PDLA) were prepared via melt blending and batch foaming process with supercritical carbon dioxide, respectively. The introduction of PDLA on the rheological properties, crystallization behavior and dynamic mechanical properties of the PLLA matrix were investigated. The formed PLA stereocomplex between PLLA and PDLA enhanced the storage modulus and complex viscosity of PLLA/PBAT blends efficiently. Interestingly, the addition of 5 wt% or 10 wt% PDLA in the PLLA/PBAT blends was unfavorable for the PLLA crystallization behavior. The potential reason can be sc-PLA crystallites acting as the physical crosslinking points, which constrained the molecular mobility of the PLLA matrix and even blocked the nucleating effect of PBAT domains. Both the enhanced melt strength and decreased crystallinity of the PLLA matrix are favorable for the cell nucleation and growth and the gas adsorption, respectively. The designed partially foaming of PLLA/PBAT with or without PDLA was carried out to investigate the foaming mechanism. The final cell morphology of PLLA/PBAT foams exhibited typical open-cell structure mainly attributed to the soft immiscible PBAT phase as separated domains. With further addition of PDLA in the PLLA/PBAT blends, the microcellular morphology exhibited decreased average cell size and increased cell density. The sc-PLA crystallites networks in the PLLA matrix acted as cell nucleating agents, which meanwhile resisted the force of cell growth and then prevented the cell collapse.

The introduced PLA stereocomplex could enhance the melting strength of PLLA/PBAT blends efficiently. The microcellular morphology of PLLA/PBAT foams with PDLA exhibited decreased average cell size and increased cell density.

Synthesis of Poly(lactic acid)-block-poly(N,N-dimethylaminoethyl methacrylate) Copolymers with Controllable Block Structures via Reversible Addition Fragmentation Polymerization from Aminolyzed Poly(lactic acid)

Poly(lactic acid)-block-poly(N,N-dimethylaminoethyl methacrylate) (PLA-PDMAEMA) copolymers were synthesized from aminolyzed PLA via reversible addition fragmentation (RAFT) polymerization. PLA undergoes aminolytic degradation with ethylenediamine (EDA). The kinetics of the aminolysis reaction of PLA at different temperatures and EDA concentrations was investigated in detail. The molar masses of products rapidly decreased in the initial stage at low aminolytic degree. Meanwhile, reactive –NH2 and –OH groups were introduced to the end of shorter PLA chains and used as sites to further immobilize the RAFT agent. PLA-PDMAEMA block copolymers were synthesized. A pseudo-first-order reaction kinetics was observed for the RAFT polymerization of PDMAEMA at a low conversion. By controlling the aminolysis reaction of PLA and RAFT polymerization degree of DMAEMA, the length distributions of the PLA and PDMAEMA blocks can be controlled. This method can be extended to more systems to obtain block copolymers with controllable block structure.

Porous Electrospun Fibers with Self-Sealing Functionality: An Enabling Strategy for Trapping Biomacromolecules

Stimuli-responsive porous polymer materials have promising biomedical application due to their ability to trap and release biomacromolecules. In this work, a class of highly porous electrospun fibers is designed using polylactide as the polymer matrix and poly(ethylene oxide) as a porogen. Carbon nanotubes (CNTs) with different concentrations are further impregnated onto the fibers to achieve self-sealing functionality induced by photothermal conversion upon light irradiation. The fibers with 0.4 mg mL-1 of CNTs exhibit the optimum encapsulation efficiency of model biomacromolecules such as dextran, bovine serum albumin, and nucleic acids, although their photothermal conversion ability is slightly lower than the fibers with 0.8 mg mL-1 of CNTs. Interestingly, reversible reopening of the surface pores is accomplished with the degradation of PLA, affording a further possibility for sustained release of biomacromolecules after encapsulation. Effects of CNT loading on fiber morphology, structure, thermal/mechanical properties, degradation, and cell viability are also investigated. This novel class of porous electrospun fibers with self-sealing capability has great potential to serve as an enabling strategy for trapping/release of biomacromolecules with promising applications in, for example, preventing inflammatory diseases by scavenging cytokines from interstitial body fluids.

3D Biofabrication of Thermoplastic Polyurethane (TPU)/Poly-l-lactic Acid (PLLA) Electrospun Nanofibers Containing Maghemite (γ-Fe₂O₃) for Tissue Engineering Aortic Heart Valve

Valvular dysfunction as the prominent reason of heart failure may causes morbidity and mortality around the world. The inability of human body to regenerate the defected heart valves necessitates the development of the artificial prosthesis to be replaced. Besides, the lack of capacity to grow, repair or remodel of an artificial valves and biological difficulty such as infection or inflammation make the development of tissue engineering heart valve (TEHV) concept. This research presented the use of compound of poly-l-lactic acid (PLLA), thermoplastic polyurethane (TPU) and maghemite nanoparticle (γ-Fe₂O₃) as the potential biomaterials to develop three-dimensional (3D) aortic heart valve scaffold. Electrospinning was used for fabricating the 3D scaffold. The steepest ascent followed by the response surface methodology was used to optimize the electrospinning parameters involved in terms of elastic modulus. The structural and porosity properties of fabricated scaffold were characterized using FE-SEM and liquid displacement technique, respectively. The 3D scaffold was then seeded with aortic smooth muscle cells (AOSMCs) and biological behavior in terms of cell attachment and proliferation during 34 days of incubation was characterized using MTT (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) assay and confocal laser microscopy. Furthermore, the mechanical properties in terms of elastic modulus and stiffness were investigated after cell seeding through macro-indentation test. The analysis indicated the formation of ultrafine quality of nanofibers with diameter distribution of 178 ± 45 nm and 90.72% porosity. In terms of cell proliferation, the results exhibited desirable proliferation (109.32 ± 3.22% compared to the control) of cells over the 3D scaffold in 34 days of incubation. The elastic modulus and stiffness index after cell seeding were founded to be 22.78 ± 2.12 MPa and 1490.9 ± 12 Nmm², respectively. Overall, the fabricated 3D scaffold exhibits desirable structural, biological and mechanical properties and has the potential to be used in vivo.

Graphene Oxide-Graft-Poly(l-lactide)/Poly(l-lactide) Nanocomposites: Mechanical and Thermal Properties

The surface modification of graphene sheets with polymer chains may greatly hinder its aggregation and improve its phase compatibility with a polymer matrix. In this work, poly(l-lactic acid)-grafted graphene oxide (GO-g-PLLA) was prepared via a simple condensation polymerization method, realizing its dispersion well in organic solvents, which demonstrated that the surface of GO changed from hydrophilic to hydrophobic. GO-g-PLLA can disperse homogeneously in the PLLA matrix, and the tensile test showed that the mechanical properties of GO-g-PLLA/PLLA were much better than that of GO/PLLA; compared with GO, only 3% GO-g-PLLA content can realize a 37.8% increase in the tensile strength for their PLLA composites. Furthermore, the differential scanning calorimetry (DSC) and polarized optical microscopy (POM) results demonstrated that GO-g-PLLA shows a nucleating agent effect and can promote the crystallization of PLLA.

Combination of Poly(lactic) Acid and Starch for Biodegradable Food Packaging

The massive use of synthetic plastics, in particular in the food packaging area, has a great environmental impact, and alternative more ecologic materials are being required. Poly(lactic) acid (PLA) and starch have been extensively studied as potential replacements for non-degradable petrochemical polymers on the basis of their availability, adequate food contact properties and competitive cost. Nevertheless, both polymers exhibit some drawbacks for packaging uses and need to be adapted to the food packaging requirements. Starch, in particular, is very water sensitive and its film properties are heavily dependent on the moisture content, exhibiting relatively low mechanical resistance. PLA films are very brittle and offer low resistance to oxygen permeation. Their combination as blend or multilayer films could provide properties that are more adequate for packaging purposes on the basis of their complementary characteristics. The main characteristics of PLA and starch in terms of not only the barrier and mechanical properties of their films but also of their combinations, by using blending or multilayer strategies, have been analyzed, identifying components or processes that favor the polymer compatibility and the good performance of the combined materials. The properties of some blends/combinations have been discussed in comparison with those of pure polymer films.

Two-Photon-Induced Microstereolithography of Chitosan-g-Oligolactides as a Function of Their Stereochemical Composition

Chitosan-g-oligolactide copolymers with relatively long oligolactide grafted chains of various stereochemical compositions have been synthetized via a solvent-free mechanochemical technique and tailored to fabricate three-dimensional hydrogels using two-photon induced microstereolithography. An effect of the characteristics of chitosan and oligolactide used for the synthesis on the grafting yield and copolymer's behavior were evaluated using fractional analysis, FTIR-spectroscopy, dynamic light scattering, and UV-spectrophotometry. The lowest copolymer yield was found for the system based on chitosan with higher molecular weight, while the samples consisting of low-molecular weight chitosan showed higher grafting degrees, which were comparable in both the cases of l,l- or l,d-oligolactide grafting. The copolymer processability in the course of two-photon stereolithography was evaluated as a function of the copolymer's characteristics and stereolithography conditions. The structure and mechanical properties of the model film samples and fabricated 3D hydrogels were studied using optical and scanning electron microscopy, as well as by using tensile and nanoindenter devices. The application of copolymer with oligo(l,d-lactide) side chains led to higher processability during two-photon stereolithography in terms of the response to the laser beam, reproduction of the digital model, and the mechanical properties of the fabricated hydrogels.

In Situ Self-Assembled Nanocomposites from Bacterial Cellulose Reinforced with Eletrospun Poly(lactic acid)/Lipids Nanofibers

The goal of this study is to explore a new strategy to improve the mechanical and hydrophobic properties of bacterial cellulose (BC) mats. The present work is the first to report the preparation of in situ self-assembled BC nanocomposites using electrospun hydrophobic poly(lactic acid) (PLA) or PLA/lipids (PLA/Lip) nanofiber mats as foundation for BC nanofiber growth. Adding electrospun PLA mats to the BC culture media led to a two-fold increase in toughness with a 52% increase in elongation of the nanocomposites with regard to BC. The incorporation of electrospun PLA and PLA/Lip nanofiber mats lowered the moisture regain and water vapor transmission of BC nanocomposites relative to pure BC mats. The interfacial bonding between the individual components of a nanocomposite is a key factor for the improvement of composite strength, stiffness, and barrier properties; thus additional strategies to improve interaction between hydrophilic BC and hydrophobic PLA fibers need to be explored.

In situ foamable, degradable polyurethane as biomaterial for soft tissue repair

Degradable foams which can be inserted endoscopically as liquid or pasty mixtures into soft tissue defects possess a promising potential for the surgical treatment of such defects. The defects can be sealed under in situ foaming and simultaneous material expansion. We developed an in situ foamable (l-lactide-co-ε-caprolactone)-based, star-shaped prepolymer by ring opening polymerization of l-lactide and ε-caprolactone in the presence of meso-erythritol as starter. By conversion of the terminal hydroxyl groups of the formed oligoester with lysine diisocyanate ethyl ester (LDI) an isocyanate-endcapped, reactive prepolymer has been received. Foaming can be initiated by addition of 1,4-diazabicyclo[2,2,2]octane (DABCO), water, LDI and DMSO. By varying the composition of these additives, the foaming and curing time could be varied within a clinically acceptable range. A porosity of approximately 90%, and an average tensile strength of 0.3MPa with elongations of 90% were determined for the foams. In vitro cytotoxicity on cured foams was assayed on 3T3 fibroblasts and demonstrated an excellent cytocompatibility. This was also confirmed in an in vivo study using an established rat model, where prefabricated foams and in situ hardening material were inserted into subdermal skin incisions in parallel. The feature of chronic inflammation was only weakly developed in both groups and slightly more pronounced and persisted for longer time in the group of in situ foamed material. In both groups the foreign materials were vascularized, degraded and substituted by connective tissue. The results encourage to proceed with trials where the materials are used to fill more heavily loaded defects.

Optimization and development of Maghemite (γ-Fe2O3) filled poly-l-lactic acid (PLLA)/thermoplastic polyurethane (TPU) electrospun nanofibers using Taguchi orthogonal array for tissue engineering heart valve

Tissue engineering (TE) is an advanced principle to develop a neotissue that can resemble the original tissue characteristics with the capacity to grow, to repair and to remodel in vivo. This research proposed the optimization and development of nanofiber based scaffold using the new mixture of maghemite (γ-Fe₂O₃) filled poly-l-lactic acid (PLLA)/thermoplastic polyurethane (TPU) for tissue engineering heart valve (TEHV). The chemical, structural, biological and mechanical properties of nanofiber based scaffold were characterized in terms of morphology, porosity, biocompatibility and mechanical behaviour. Two-level Taguchi experimental design (L8) was performed to optimize the electrospun mats in terms of elastic modulus using uniaxial tensile test where the studied parameters were flow rate, voltage, percentage of maghemite nanoparticles in the content, solution concentration and collector rotating speed. Each run was extended with an outer array to consider the noise factors. The signal-to-noise ratio analysis indicated the contribution percent as follow; Solution concentration>voltage>maghemite %>rotating speed>flow rate. The optimum elastic modulus founded to be 28.13±0.37MPa in such a way that the tensile strain was 31.72% which provided desirability for TEHV. An empirical model was extracted and verified using confirmation test. Furthermore, an ultrafine quality of electrospun nanofibers with 80.32% porosity was fabricated. The MTT (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) assay and cell attachment using human aortic smooth muscle cells exhibited desirable migration and proliferation over the electrospun mats. The interaction between blood content and the electrospun mats indicated a mutual adaption in terms of clotting time and hemolysis percent. Overall, the fabricated scaffold has the potential to provide the required properties of aortic heart valve.

In vitro antiherpes effect of C-glycosyl flavonoid enriched fraction of Cecropia glaziovii encapsulated in PLGA nanoparticles

In this work is reported a novel and promising approach for the preparation of C-glycosylflavonoid enriched fraction of Cecropia glaziovii (EFF-Cg) loaded PLGA nanoparticles (NP) with antiherpes properties. The purpose of this study was to evaluate and to compare the effect of two nonionic surfactants (poloxamer 188 (PLU) and polyvinyl alcohol (PVA)), and also an emulsion stabilized by solid particles of cellulose nanocrystal (CNC) in place of surfactants. The characterization of these nanoparticles was in terms of size, polydispersity index, zeta potential, morphology, thermogravimetric analysis (TGA), loading capacity and percent yield. Since TGA analysis revealed thermo stability especially for NP-PLU, this formulation was selected for the evaluation of drug release profile, cytotoxicity and antiherpes activity. The drug delivery profile demonstrated a sustained release through the polymer structure and a significant reduction of the polymer molecular weight at 21-day period. The cytotoxicity of these nanoparticles was determined on Vero cells, and the selected formulation did not exhibit cytotoxicity even at the highest tested concentration. The results demonstrated a potential antiherpetic effect of the EFF-Cg loaded NP at 48h of testing. In summary, EFF-Cg loaded NP exhibited a promising system for the effective drug delivery in the treatment of herpes infections.

Insight into the role of bound water of a nucleating agent in polymer nucleation: a comparative study of anhydrous and monohydrated orotic acid on crystallization of poly(l-lactic acid)

The bound water of orotic acid and its dehydration transition play a negative role in nucleation effects on PLLA crystallization.

The generation of myricetin-nicotinamide nanococrystals by top down and bottom up technologies

Myricetin-nicotinamide (MYR-NIC) nanococrystal preparation methods were developed and optimized using both top down and bottom up approaches. The grinding (top down) method successfully achieved nanococrystals, but there were some micrometer range particles and aggregation. The key consideration of the grinding technology was to control the milling time to determine a balance between the particle size and distribution. In contrast, a modified bottom up approach based on a solution method in conjunction with sonochemistry resulted in a uniform MYR-NIC nanococrystal that was confirmed by powder x-ray diffraction, scanning electron microscopy, dynamic light scattering, and differential scanning calorimeter, and the particle dissolution rate and amount were significantly greater than that of MYR-NIC cocrystal. Notably, this was a simple method without the addition of any non-solvent. We anticipate our findings will provide some guidance for future nanococrystal preparation as well as its application in both chemical and pharmaceutical area.

Development and characterisation of HPMC films containing PLA nanoparticles loaded with green tea extract for food packaging applications

A novel active film material based on hydroxypropyl-methylcellulose (HPMC) containing poly(lactic acid) (PLA) nanoparticles (NPs) loaded with antioxidant (AO) green tea extract (GTE) was successfully developed. The PLA NPs were fabricated using an emulsification-solvent evaporation technique and the sizes were varied to enable a controlled release of the AO from the HPMC matrix. A statistical experimental design was used to optimise the synthesis of the NPs in order to obtain different sizes of nanoparticles and the loading of these into the HPMC matrix was also varied. The physico-chemical properties of the composite films were investigated and the release of the AO was confirmed by migration studies in 50% v/v ethanol/water food simulant. The AO capacity of the GTE released from the active films was studied using the 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical method and the results suggest that the material could potentially be used for extending the shelf-life of food products with high fat content.