Review on Methylene Blue: Its Properties, Uses, Toxicity and Photodegradation

Synthesis of Metalorganic Copolymers Containing Various Contorted Units and Iron(II) Clathrochelates with Lateral Butyl Chains: Conspicuous Adsorbents of Lithium Ions and Methylene Blue

We report the synthesis of three highly soluble metalorganic copolymers, TCP1-3, that were made from a one-pot complexation of iron(II) clathrochelate units that are interconnected by various thioether-containing contorted groups. TCP1-3 were converted into their poly(vinyl sulfone) derivatives OTCP1-3 quantitatively via the selective oxidation of the thioether moieties into their respective sulfones. All of the copolymers, TCP1-3 and OTCP1-3, underwent structural analysis by various techniques; namely, ¹H- and ¹³C-nuclear magnetic resonance (NMR), Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS), and gel permeation chromatography (GPC). The copolymers were tested as potent lithium ions adsorbents revealing a maximum adsorption (q_m) value of 2.31 mg g^-1 for OTCP2. Furthermore, this same copolymer was found to be a promising adsorbent of methylene blue (MEB); an isothermal adsorption study divulged that OTCP2's uptake of MEB from an aqueous solution (following the Langmuir model) was, at maximum adsorption capacity, (q_m) of 480.77 mg g^-1; whereas the kinetic study divulged that the adsorption follows pseudo second-order kinetics with an equilibrium adsorption capacity (q_e,cal) of 45.40 mg g^-1.

Adsorption of Organic Compounds on Adsorbents Obtained with the Use of Microwave Heating

Activated carbons were obtained by physical and chemical activation of the residue of supercritical extraction of green tea leaves. All the adsorbents obtained were characterized by: elemental analysis, low-temperature nitrogen adsorption, and the contents of acidic and basic oxygen functional groups on the surface of activated carbons by the Boehm method. The activated carbons were micro- or micro-mesoporous with well-developed surface area ranging from 520 to 1085 m²/g and total pore volume from 0.62 to 0.64 cm³/g. The physical activation of the precursor led to the strongly basic character of the surface. Chemical activation with 50% solution of H₃PO₄ of the residue of supercritical extraction of green tea leaves promoted the generation of acidic functional groups. All adsorbents were used for methylene blue and methyl red adsorption from the liquid phase. The influence of the activation method, pH of the dye solution, contact time of adsorbent with adsorbate, the temperature of adsorption, and rate of sample agitation on the effectiveness of organic dyes removal was evaluated and optimized. In the process of methylene blue adsorption on adsorbents, an increase in the sorption capacity was observed with increasing pH of the adsorbate, while in the process of methyl red adsorption, the relation was quite the reverse. The adsorption data were analyzed assuming the Langmuir or Freundlich isotherm models. The Langmuir model better described the experimental results, and the maximum sorption capacity calculated for this model varied from 144.93 to 250.00 mg/g. The results of the kinetic analysis showed that the adsorption of organic dyes on activated carbon was following the pseudo-second-order model. The negative values of the Gibbs free energy indicate the spontaneous character of the process.

Rapid and efficient adsorption of methylene blue dye from aqueous solution by hierarchically porous, activated starbons®: Mechanism and porosity dependence

Hierarchically porous activated Starbons® derived from starch are found to make excellent adsorbents for methylene blue, even in the presence of other dyes and inorganic salts, highlighting their potential to be used in water purification. The optimal material (S950C90) has a methylene blue adsorption capacity (891 mg g^-1) almost nine times higher than that of unactivated S800 and four times higher than that of commercial activated carbon at 298 K. The adsorption of methylene blue onto optimal materials (S950C90 and S800K4) reaches equilibrium within 5 min. Adsorption data for all the adsorbents show a good fit to the Freundlich isotherm which allows the Gibbs free energies of adsorption to be calculated. The adsorption capacities increase as the pH of the methylene blue solution increases, allowing the dye to be desorbed by treatment with acidic ethanol and the Starbon® materials reused. Porosimetry and SEM-EDX imaging indicate that methylene blue adsorbs throughout the surface and completely fills all the micropores in the Starbon® adsorbent. The methylene blue adsorption capacities show excellent correlations with both the BET surface areas and the micropore volumes of the materials.

Biodegradation of Azo Dye Methyl Red by Pseudomonas aeruginosa: Optimization of Process Conditions

Water pollution due to textile dyes is a serious threat to every life form. Bacteria can degrade and detoxify toxic dyes present in textile effluents and wastewater. The present study aimed to evaluate the degradation potential of eleven bacterial strains for azo dye methyl red. The optimum degradation efficiency was obtained using P. aeruginosa. It was found from initial screening results that P. aeruginosa is the most potent strain with 81.49% degradation activity and hence it was subsequently used in other degradation experiments. To optimize the degradation conditions, a number of experiments were conducted where only one variable was varied at a time and where maximum degradation was observed at 20 ppm dye concentration, 1666.67 mg/L glucose concentration, 666.66 mg/L sodium chloride concentration, pH 9, temperature 40 °C, 1000 mg/L urea concentration, 3 days incubation period, and 66.66 mg/L hydroquinone (redox mediator). The interactive effect of pH, incubation time, temperature, and dye concentration in a second-order quadratic optimization of process conditions was found to further enhance the biodegradation efficiency of P. aeruginosa by 88.37%. The metabolites of the aliquot mixture of the optimized conditions were analyzed using Fourier transform infrared (FTIR), GC-MS, proton, and carbon 13 Nuclear Magnetic Resonance (NMR) spectroscopic techniques. FTIR results confirmed the reduction of the azo bond of methyl red. The Gas Chromatography-Mass Spectrometry (GC-MS) results revealed that the degraded dye contains benzoic acid and o-xylene as the predominant constituents. Even benzoic acid was isolated from the silica gel column and identified by ¹H and ¹³C NMR spectroscopy. These results indicated that P. aeruginosa can be utilized as an efficient strain for the detoxification and remediation of industrial wastewater containing methyl red and other azo dyes.

Fast Removal of Methylene Blue via Adsorption-Photodegradation on TiO2/SBA-15 Synthesized by Slow Calcination

TiO₂/SBA-15 photocatalysts were successfully prepared by impregnating low loading titania to SBA-15 via slow calcination. The photocatalyst is efficient for fast methylene blue removal via adsorption and photodegradation methods. The impregnation of low TiO₂ loading via slow calcination enhanced TiO₂ dispersion that preserved the SBA-15 porosity and uniform morphology. High interfacial interaction of TiO₂/SBA-15 improves TiO₂ photoresponse by narrowing the bandgap, resulting in a stronger redox ability. The methylene blue removal on 10%TiO₂/SBA-15 followed the pseudo-second-order kinetic model that reached 67% removal efficiency in 90 min. The synergy between adsorption and photodegradation is responsible for the fast methylene blue removal. These results indicate the importance of maintaining the adsorption capacity in SBA-15 after impregnation with TiO₂ for efficient adsorption-photodegradation processes, which can be achieved by controlling the deposition of TiO₂ on SBA-15. A low titania loading further reduced the cost of photocatalysts, thus becoming a potential material for environmental pollution treatment.

Development, Synthesis and Characterization of Tannin/Bentonite-Derived Biochar for Water and Wastewater Treatment from Methylene Blue

Novel hybrid carbon–mineral materials were synthesized by the mechanochemical activation of a mixture of tannin and bentonite in a ball mill with further pyrolysis in an argon atmosphere at 800 °C. The influence of the initial mixture ingredients content on the structural, textural, and thermal characteristics of biochars has been described using X-ray diffraction, Raman and Fourier-transform infrared spectroscopy, nitrogen adsorption–desorption, and scanning electron microscopy. The influence of bentonite clay on the carbon phase characteristics due to the formation of more heat-resistant and structured nanocarbon particles in biochars has been proven. The adsorption effectiveness of the materials towards methylene blue was studied. The adsorption data were analyzed applying Langmuir and Freundlich isotherms with high determination coefficients (R2) in the range of 0.983–0.999 (Langmuir) and 0.783–0.957 (Freundlich). The maximum adsorption amount of MB was 5.78 mg/g. The adsorption efficiency of biochars with respect to phenol was also examined. It was shown that the hybrid biochars show differentiated selectivity to the adsorption of organic compounds. It was concluded that the physicochemical properties of the surface of biochars play an important role in the adsorption effectiveness, making them a good candidate for water and wastewater remediation processes.

Enhanced photocatalytic potential of TiO2 nanoparticles in coupled CdTiO2 and ZnCdTiO2 nanocomposites

Photodegradation of organic pollutants is the most suitable and cheaper technique to counter decontamination issues. Among the metal-based nanoparticles, TiO₂ is considered to be the most effective heterogeneous photocatalyst for the photodegradation of organic pollutants. However, the large band gap and the high electron-hole pair recombination rate limit its practical applications. Herein, an approach was introduced to minimize the mentioned limitations by preparing CdTiO₂ and ZnCdTiO₂ nanocomposites by co-precipitation method. The as-synthesized TiO₂, CdTiO₂, and ZnCdTiO₂ were characterized by scanning electron microscopy, transmission electron microscopy (TEM), energy dispersive X-ray, X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), and UV-visible spectrophotometry. Morphological analysis revealed that TiO₂ are mostly agglomerated with different shapes and sizes and the nanocomposites are mostly in dispersed form. The components of the nanocomposites are strongly intercalated in the ternary nanocomposite as confirmed from TEM analysis. XRD analysis confirmed the anatase TiO₂ while the UV-visible analysis showed the shifting toward higher wavelength. The band gap energy of TiO₂ (2.65) decreased to 2.6 and 2.56 eV for CdTiO₂ and ZnCdTiO₂, respectively. BET analysis has shown a 47.2 m²/g surface area for the ternary ZnCdTiO₂ nanocomposite. The photodegradation results revealed that TiO₂, CdTiO₂, and ZnCdTiO₂ degraded about 74%, 86%, and 97.61% methylene blue dye, respectively, within 2 h. Maximum photodegradation is achieved in the basic medium and the ternary ZnCdTiO₂ nanocomposite degraded 98% dye at pH 10.

Hydrogenation of Xylose to Xylitol in the Presence of Bimetallic Nanoparticles Ni3Fe Catalyst in the Presence of Choline Chloride

Hydrogenation of sugars to sugars alcohols is of prime interest for food applications for instance. Xylose obtained from the hemicellulose fraction of lignocellulosic biomass can be hydrogenated to xylitol. Herein, we conducted catalytic hydrogenation reactions in a non-conventional media approach by using choline chloride, a non-toxic naturally occurring organic compound that can form a deep eutectic solvent with xylose. Acknowledging the benefits of cost-effective transition metal-based alloys, Ni3Fe1 bimetallic nanoparticles were utilized as a hetero-catalyst. Under optimized reaction conditions (110 °C, 3 h and 30 bar H2), a highly concentrated feed of xylose (76 wt.%) was converted to 80% of xylitol, showing the benefit of using choline chloride. Overall, the catalytic conversion activity and the product selectivity in the substrate-assisted DES media are relatively high but, the recyclability of the catalyst should be improved in the presence of such media.

Antimicrobial Activity of a Titanium Dioxide Additivated Thermoset

The transmission of pathogens via surfaces poses a major health problem, particularly in hospital environments. Antimicrobial surfaces can interrupt the path of spread, while photocatalytically active titanium dioxide (TiO2) nanoparticles have emerged as an additive for creating antimicrobial materials. Irradiation of such particles with ultraviolet (UV) light leads to the formation of reactive oxygen species that can inactivate bacteria. The aim of this research was to incorporate TiO2 nanoparticles into a cellulose-reinforced melamine-formaldehyde resin (MF) to obtain a photocatalytic antimicrobial thermoset, to be used, for example, for device enclosures or tableware. To this end, composites of MF with 5, 10, 15, and 20 wt% TiO2 were produced by ultrasonication and hot pressing. The incorporation of TiO2 resulted in a small decrease in tensile strength and little to no decrease in Shore D hardness, but a statistically significant decrease in the water contact angle. After 48 h of UV irradiation, a statistically significant decrease in tensile strength for samples with 0 and 10 wt% TiO2 was measured but with no statistically significant differences in Shore D hardness, although a statistically significant increase in surface hydrophilicity was measured. Accelerated methylene blue (MB) degradation was measured during a further 2.5 h of UV irradiation and MB concentrations of 12% or less could be achieved. Samples containing 0, 10, and 20 wt% TiO2 were investigated for long-term UV stability and antimicrobial activity. Fourier-transform infrared spectroscopy revealed no changes in the chemical structure of the polymer, due to the incorporation of TiO2, but changes were detected after 500 h of irradiation, indicating material degradation. Specimens pre-irradiated with UV for 48 h showed a total reduction in Escherichia coli when exposed to UV irradiation.

Synthesis and Characterization Bimetallic Organic Framework CoxFex(BDC) and Adsorption Cationic and Anionic Dyes

Co-doped Fe-MOF bimetallic organic framework materials at different ratios were synthesized based on the solvothermal method, and we evaluated their morphological characteristics by modern analytical methods such as SEM, XRD, FT-IR, and isotherm of nitrogen adsorption-desorption (BET). The specific surface area of the 0.3 CoFe-MOF sample (280.9 m2/g) is much larger than the Fe-MOF and samples at other ratios. The post-synthesized materials were evaluated for their ability to absorb various dyes, including Methylene Blue (MB), Methyl orange (MO), Congo red (CR), and Rhodamine (RhB), and evaluated for the effects of pH, the initial concentration of the dye solution, time, and dose of adsorbent. The results show that the 0.3 CoFe-MOF material has a high adsorption capacity that is superior to both the original Fe-MOF and the CoFe-MOFs at other ratios. The highest adsorption capacity of MB dye by 0.3 CoFe-MOF reaches up to 562.1 mg/g at pH 10, the initial concentration of MB of 200 mg/L, after 90 min. The charged properties of the dyes and the charged nature of the bimetallic organic frameworks are best demonstrated through the adsorption of dye mixtures. The adsorption efficiency on the mixed system of cationic (MB) and anionic (MO) dyes yielded the highest removal efficiency of 70% and 81%, respectively, after 30 min. Therefore, the research has opened up the potential application of M/Fe-MOF modified materials and CoFe-MOF in organic dyes adsorption in wastewater treatment for environmental protection.

Biosorbents Based on Biopolymers from Natural Sources and Food Waste to Retain the Methylene Blue Dye from the Aqueous Medium

The use of a biosorbent based on residual biomass from brewing industry (Saccharomyces pastorianus) immobilized in a natural biopolymer (sodium alginate) was investigated for Methylene Blue removal from aqueous medium. Saccharomyces pastorianus, immobilized by a simple entrapment technique and by microencapsulation in alginate was characterized using SEM, EDAX, pHPZC and the biosorption behavior toward organic pollutant, such as cationic dye. The biosorption experiments were studied by assessing, in a first stage, the influence of the most important operational physical parameters on the efficiency of the biosorbent: the initial concentration of the dye, the contact time between phases, the temperature, the dye solution pH, the biosorbent granule size, and the amount of biosorbent. The highest sorption capacity was obtained for the biosorbent obtained by microencapsulation, at pH 9, at biosorbent dose of 5.28 g/L and a contact time of about 100 min. The biosorption equilibrium was then studied by modeling the data on the Langmuir, Freundlich and Dubinin- Radushkevich isotherms. The Langmuir model is best suited for experimental data on both particle sizes leading to a maximum biosorption capacity of 188.679 mg/g at room temperature. The values of the adsorption energy, E, obtained with the help of the Dubinin-Radushkevich model-suggest that the type of mechanism (physical or chemical) involved in the biosorption process depends on the particle size of the biosorbent. The results confirm that the residual microbial biomass of Saccharomyces pastorianus immobilized in a polymeric matrix such as sodium alginate, can be considered an efficient biosorbent in retaining cationic organic dyes present in aqueous solutions in moderate concentrations.

Photocatalytic Conversion of Fructose to Lactic Acid by BiOBr/Zn@SnO2 Material

Photocatalysis provides a prospective approach for achieving high-value products under mild conditions. To realize this, constructing a selective, low-cost and environmentally friendly photocatalyst is the most critical factor. In this study, BiOBr/Zn@SnO2 is fabricated by a one-pot hydrothermal synthesis method and BiOBr: SnO2 ratio is 3:1; this material is applied as photocatalyst in fructose selective conversion to lactic acid. The bandgap structure can be regulated via two-step modification, which includes Zn doping SnO2 and Zn@SnO2 coupling BiOBr. The photocatalyst shows excellent conversion efficiency in fructose and high selectivity in lactic acid generation under alkaline conditions. The conversion rate is almost 100%, and the lactic acid yield is 79.6% under optimal reaction conditions. The catalyst is highly sustainable in reusability; the lactic acid yield can reach 67.4% after five runs. The possible reaction mechanism is also proposed to disclose the photocatalysis processes.

Rice Straw as Green Waste in a HTiO2@AC/SiO2 Nanocomposite Synthesized as an Adsorbent and Photocatalytic Material for Chlorpyrifos Removal from Aqueous Solution

A nano-HTiO2@activated carbon-amorphous silica nanocomposite catalyst (HTiO2@AC/SiO2) is utilized to photo breakdown catalytically and adsorb chlorpyrifos insecticide. SEM, TEM, and X-ray diffraction were used to examine HTiO2@AC/SiO2, synthesized through sol–gel synthesis. With an average size of 7–9 nm, the crystallized form of HTiO2 is the most common form found. At varied pH, catalyst doses, agitation speed, initial pesticide concentrations, contact periods, and temperatures, HTiO2@AC/SiO2 was examined for efficiency under visible light and in darkness. Because of the pseudo-second-order kinetics observed for chlorpyrifos, chemisorption is believed to dominate the adsorption process, as indicated by an estimated activation energy of 182.769 kJ/mol, which indicates that chemisorption dominates the adsorption process in this study. The maximal adsorption capacity of chlorpyrifos is 462.6 mg g−1, according to the Langmuir isotherms, which infer this value. When exposed to visible light, the adsorption capacity of HTiO2@AC/SiO2 increased somewhat as the temperature rose (283 k 323 k 373 k), indicating an exothermic change in Gibbs free energy during the process (−1.8 kJ/mol), enthalpy change (−6.02 kJ/mol), and entropy change (0.014 J/mol K), respectively, at 298.15 K. Negative (ΔS) describes a process with decreased unpredictability and suggests spontaneous adsorption. HTiO2@AC/SiO2 may be a promising material.

Efficient Removal of Methylene Blue and Ciprofloxacin from Aqueous Solution Using Flower-like, Nanostructured ZnO Coating under UV Irradiation

Flower-like ZnO architectures assembled with many nanorods were successfully synthesized through Thermionic Vacuum Arc, operated both in direct current (DC-TVA) and a pulsed mode (PTVA), and coupled with annealing in an oxygen atmosphere. The prepared coatings were analysed by scanning-electron microscopy with energy-dispersive X-ray-spectroscopy (SEM-EDX), X-ray-diffraction (XRD), and photoluminescence (PL) measurements. By simply modifying the TVA operation mode, the morphology and uniformity of ZnO nanorods can be tuned. The photocatalytic performance of synthesized nanostructured ZnO coatings was measured by the degradation of methylene-blue (MB) dye and ciprofloxacin (Cipro) antibiotic. The ZnO (PTVA) showed enhancing results regarding the photodegradation of target contaminants. About 96% of MB molecules were removed within 60 min of UV irradiation, with a rate constant of 0.058 min−1, which is almost nine times higher than the value of ZnO (DC-TVA). As well, ZnO (PTVA) presented superior photocatalytic activity towards the decomposition of Cipro, after 240 min of irradiation, yielding 96% degradation efficiency. Moreover, the agar-well diffusion assay performance against both Gram-positive and Gram-negative bacteria confirms the degradation of antibiotic molecules by the UV/ZnO (PTVA) approach, without the formation of secondary hazardous products during the photocatalysis process. Repeated cyclic usage of coatings revealed excellent reusability and operational stability.

Zero-Valent Copper-Mediated Peroxymonosulfate Activation for Efficient Degradation of Azo Dye Orange G

Zero-valent metal (ZVMs)-based persulfate activation systems are extensively applied for the elimination of organic pollutants in aqueous environments. In this study, for the first time, zero-valent copper (ZVC) was employed as the peroxymonosulfate (PMS) activator for the efficient degradation of Orange G (OG). The physicochemical properties of ZVC were systematically characterized by FESEM, EDX, TEM, XRD and XPS measurements. Furthermore, the effects of catalyst loading, PMS dosage, OG concentration and inorganic anions on the ZVC/PMS system were, respectively, investigated and explicated. The formation of •OH and SO4•− in the system was verified by quenching experiments and then the possible reaction mechanism was proposed. This work can provide insight into water treatment technology based on ZVMs.

Degradation of Rhodamine B in Wastewater by Iron-Loaded Attapulgite Particle Heterogeneous Fenton Catalyst

The water pollution caused by industry emissions makes effluent treatment a serious matter that needs to be settled. Heterogeneous Fenton oxidation has been recognized as an effective means to degrade pollutants in water. Attapulgite can be used as a catalyst carrier because of its distinctive spatial crystal structure and surface ion exchange. In this study, iron ions were transported on attapulgite particles to generate an iron-supporting attapulgite particles catalyst. BET, EDS, SEM and XRD characterized the catalysts. The particle was used as a heterogeneous catalyst to degrade rhodamine B (RhB) dye in wastewater. The effects of H2O2 concentration, initial pH value, catalyst dosage and temperature on the degradation of dyes were studied. The results showed that the decolorization efficiency was consistently maintained after consecutive use of a granular catalyst five times, and the removal rate was more than 98%. The degradation and mineralization effect of cationic dyes by granular catalyst was better than that of anionic dyes. Hydroxyl radicals play a dominant role in RhB catalytic degradation. The dynamic change and mechanism of granular catalysts in catalytic degradation of RhB were analyzed. In this study, the application range of attapulgite was widened. The prepared granular catalyst was cheap, stable and efficient, and could be used to treat refractory organic wastewater.

Bioremediation potential of Dicentrarchus labrax fish scales for dye-based emerging contaminants by ANN-GA hybrid modeling

This work investigates the possibility of using scales of sea bass Dicentrarchus labrax as a low-cost material for the adsorptive removal of methylene blue (MB) cationic dye in aqueous solutions. The physical-chemical characterizations of fish scales in natura (FS-in natura) revealed through thermogravimetry that they are composed of inorganic (hydroxyapatite) and organic (collagen) phases in relatively similar amounts. Spectroscopy analyses show that the interactions of MB with FS-in natura occur mainly in the organic phase layer of the adsorbent. The effects of initial MB concentration (5.0 × 10^-4 and 5.0 × 10^-3 mol L^-1) and temperature (25-55 °C) on the adsorption efficiency of FS-in natura were evaluated. FS-in natura at MB concentration (5.0 × 10^-3 and 5.0 × 10^-4 mol L^-1) exhibited the maximum adsorption capacities of 2.2 × 10^-3 mol g^-1 at 25 °C and 2.8 × 10^-5 mol g^-1 at 55 °C, respectively. The pseudo-second-order model represented the adsorption kinetics well, and the equilibrium isotherm data were better correlated using the Langmuir equation. The newly developed neural model demonstrated a high predictive capacity with an R-value greater than 0.99 and reduced values for mean squared error, root mean squared error, and mean absolute error equal to 0.003, 0.055, and 0.0348, respectively. The genetic algorithm was used to optimize the experimental conditions of the process. In conclusion, the sea bass scales have promising prospects as a low-cost alternative material for removing cationic dyes from aqueous solutions.

Adsorption of Cationic Pollutants from Water by Cotton Rope Coated with Cyclodextrin Polymers

The contamination from perilous organic compounds (pesticide and dyes) in water generates a significant problem for the environment and humans. A modified textile was prepared by a coating of anionic cyclodextrin polymer, obtained from the cross-linking between citric acid and β-cyclodextrin in the presence of poly (vinyl alcohol), on the cotton cord for cationic pollutant removal from an aqueous solution. Its physicochemical properties were also characterized by gravimetry, titration, stereomicroscopy, SEM, TGA, ¹³C NMR, and ATR-FTIR. The CC2 system exhibited 79.2% coating yield, 1.12 mmol/g COOH groups, 91.3% paraquat (PQ) removal, 97.0% methylene blue (MB) removal, and 98.3% crystal violet (CV) removal for 25 mg/L of initial concentration. The kinetics was fitted to the pseudo-second-order model using 6 h of contact time. The isotherm was suitable for the Langmuir isotherm with a maximum adsorption of 26.9 mg/g (PQ), 23.7 mg/g (MB), and 30.3 mg/g (CV). After 120 h of contact time in water and 5% v/v of HCI in ethanol, the weight loss was 7.5% and 5.6%, respectively. Finally, the recyclability performance reached 84.8% (PQ), 95.2% (MB), and 96.9% (CV) after five reuses.

Visible Light-Induced Photocatalyst with Au/TiO2 Nanocomposites Fabricated through Pulsed Laser-Induced Photolysis

Gold–titanium oxide nanocomposites (Au–TiO2 NCPs) were fabricated through pulsed laser-induced photolysis (PIPS) and verified to be usable for the visible light catalytic degradation of methylene blue (MB). The PIPS method can produce a sufficient amount of NCPs quickly and has potential to be commercialized. In contrast to other studies, we clarified the optical spectrum of the light sources, including peak power, bandwidth, and total intensity used for photodegradation reactions and discovered that the photodegradation efficiency of the produced Au–TiO2 NCPs in the wavelength range of 405 nm could reach 37% in 30 min due to the charge transfer between Au and TiO2. The control experiment shows that the addition of individual Au and TiO2 nanoparticles (NPs) to an MB solution has no enhancement of degradation ability under visible light illumination. The photodegradation of Au–TiO2 NCPs can be further improved by increasing the concentrations of auric acid and TiO2 NPs in a precursor under PIPS fabrication.

[Cu(C3H3N3S3)3] Adsorption onto ZnTiO3/TiO2 for Coordination-Complex Sensitized Photochemical Applications

Currently, the design of highly efficient materials for photochemical applications remains a challenge. In this study, an efficient semiconductor was prepared, based on a coordination complex (Cu-TTC) of Cu(I) and trithiocyanuric acid on ZnTiO₃/TiO₂ (ZTO/TO). The Cu-TTC/ZTO/TO composite was prepared by the solvothermal method at room temperature. The structural, optical, and electrochemical characteristics, as well as the photocatalytic performance of the composite, were experimentally and computationally studied. The results show that the Cu-TTC/ZTO/TO composite efficiently extended its photoresponse in the visible region of the electromagnetic spectrum. The electrochemistry of the proposed tautomeric architecture (s-Cu-TTC) clearly reveals the presence of metal–ligand charge-transfer (MLCT) and π → π* excitations. The maximum methylene blue (MB) dye photodegradation efficiency of 95% in aqueous solutions was achieved under the illumination of simulated solar light. Finally, computational calculations based on the Density Functional Theory (DFT) method were performed to determine the electronic properties of the s-Cu-TTC tautomeric structure and clarify the adsorption mechanism of this complex on the surface (101) of both ZnTiO₃ and TiO₂ oxides. The results obtained allow us to suggest that the Cu-TTC complex is an effective charge carrier and that the Cu-TTC/ZTO/TO composite can be used efficiently for photochemical applications.

Magnetic Core-Shell Iron Oxides-Based Nanophotocatalysts and Nanoadsorbents for Multifunctional Thin Films

In recent years, iron oxides-based nanostructured composite materials are of particular interest for the preparation of multifunctional thin films and membranes to be used in sustainable magnetic field adsorption and photocatalysis processes, intelligent coatings, and packing or bio-medical applications. In this paper, superparamagnetic iron oxide (core)-silica (shell) nanoparticles suitable for thin films and membrane functionalization were obtained by co-precipitation and ultrasonic-assisted sol-gel methods. The comparative/combined effect of the magnetic core co-precipitation temperature (80 and 95 °C) and ZnO-doping of the silica shell on the photocatalytic and nano-sorption properties of the resulted composite nanoparticles were investigated by ultraviolet-visible (UV-VIS) spectroscopy monitoring the discoloration of methylene blue (MB) solution under ultraviolet (UV) irradiation and darkness, respectively. The morphology, structure, textural, and magnetic parameters of the investigated powders were evidenced by scanning electron microscopy (SEM), X-ray diffraction (XRD), Raman spectroscopy, Brunauer–Emmett–Teller (BET) measurements, and saturation magnetization (vibrating sample magnetometry, VSM). The intraparticle diffusion model controlled the MB adsorption. The pseudo- and second-order kinetics described the MB photodegradation. When using SiO₂-shell functionalized nanoparticles, the adsorption and photodegradation constant rates are three–four times higher than for using starting core iron oxide nanoparticles. The obtained magnetic nanoparticles (MNPs) were tested for films deposition.

Studies of Clinoptilolite-Rich Zeolitic Tuffs from Different Regions and Their Activity in Photodegradation of Methylene Blue

The present study focuses on clinoptilolite (CLI)-rich natural zeolitic tuffs and their photocatalytic activity in the degradation of cationic organic dyes. CLI from different regions was tested in the photocatalytic degradation of methylene blue (MB) as a model cationic dye. The photocatalytic tests were performed at room temperature and atmospheric pressure under visible light irradiation. For all the CLI samples, the highest activity was observed at pH = 6. Total MB degradation varied between 70 and 91% (C0 = 10 mg dm–3, 0.2 g dm–3 of photocatalyst, during 300 min). It is suggested that the presence of Fe species in the studied tuffs is responsible for the photocatalytic activity. The activity increases linearly with the Fe content in the tuffs. The MB photodegradation follows the Langmuir–Hinshelwood kinetic model. The recyclability tests showed good stability and efficiency of the photocatalyst. The degradation rate decreased from 91 to 69% during three reaction cycles, indicating a promising potential of natural zeolites in the treatment of textile industry wastewater.

Alginate-based hydrogels embedded with ZnO nanoparticles as highly responsive colorimetric oxygen indicators

Simple fabrication of hydrogel-based colorimetric oxygen indicators as alternative smart materials for oxygen sensitive products and systems.