Characteristics of equilibrium, kinetics studies for adsorption of Hg(II), Cu(II), and Ni(II) ions by thiourea-modified magnetic chitosan microspheres

Porous CS monoliths and their adsorption ability for heavy metal ions

Highly porous chitosan (CS) monoliths were prepared by a unidirectional freeze-drying method and the adsorption performance of the monoliths for metal ions in aqueous solution was evaluated. The porous CS monoliths have excellent adsorption for a range of metal ions. The effect of the amount of porous CS monoliths, the pH, the adsorption time, the amount of the cross-linking agent, and the amount of disodium ethylenediamine tetraacetate (EDTA) on the saturated adsorption efficiency (Ade) were determined. The pH had the greatest influence on the adsorption behavior. Under optimal conditions (C(CU²⁺) = 800 mg/L, pH 6, and cross-linking agent = 0.15%) for the CS monoliths, the Ade for Cu(2+) exceeded 99%, and the saturated adsorption capacity (Q(s)) reached a value of 141.8 mg/g (2.23 mmol/g) in 4h. Moreover, the addition of EDTA can both increase the Q(s) and shorten the time that achieved the level. If EDTA was added, this level was achieved in 2h. The porous CS monoliths can be regenerated by soaking them in acid and their Ade is maintained.

Adsorption of chromium (VI) by ethylenediamine-modified cross-linked magnetic chitosan resin: isotherms, kinetics and thermodynamics

The adsorption of chromium (VI) ions from aqueous solution by ethylenediamine-modified cross-linked magnetic chitosan resin (EMCMCR) was studied in a batch adsorption system. Chromium (VI) removal is pH dependent and the optimum adsorption was observed at pH 2.0. The adsorption rate was extremely fast and the equilibrium was established within 6-10min. The adsorption data could be well interpreted by the Langmuir and Temkin model. The maximum adsorption capacities obtained from the Langmuir model are 51.813mgg(-1), 48.780mgg(-1) and 45.872mgg(-1) at 293, 303 and 313K, respectively. The adsorption process could be described by pseudo-second-order kinetic model. The intraparticle diffusion study revealed that film diffusion might be involved in the present case. Thermodynamic parameters revealed the feasibility, spontaneity and exothermic nature of adsorption. The sorbents were successfully regenerated using 0.1N NaOH solutions.

Preparation and characterization of chelating fibers based on natural wool for removal of Hg(II), Cu(II) and Co(II) metal ions from aqueous solutions

The graft copolymerization of acrylonitrile (AN) onto natural wool fibers initiated by KMnO(4) and oxalic acid combined redox initiator system in limited aqueous medium was carried out in heterogeneous media. Moreover, modification of the grafted wool fibers was done by changing the nitrile group (-CN) into cyano-acetic acid α-amino-acrylic-hydrazide through the reaction with hydrazine hydrate followed by ethylcyanoacetate which eventually produce wool-grafted-poly(cyano-acetic acid α-amino-acrylic-hydrazide) (wool-g-PCAH) chelating fibers. The application of the modified fibers for metal ion uptake was studied using Hg(2+), Cu(2+) and Co(2+). The modified chelating fibers were characterized using FTIR spectroscopy, SEM and X-ray diffraction.

Adsorption and desorption of Cu(II), Cd(II) and Pb(II) ions using chitosan crosslinked with epichlorohydrin-triphosphate as the adsorbent

In this study, chitosan (CTS) was crosslinked with both epichlorohydrin (ECH) and triphosphate (TPP), by covalent and ionic crosslinking, respectively. The resulting new CTS-ECH-TPP adsorbent was characterized by CHN analysis, EDS, FTIR spectroscopy, TGA and DSC, and the adsorption and desorption of Cu(II), Cd(II) and Pb(II) ions in aqueous solution were investigated. Potentiometric studies were also performed and revealed three titratable protons for each pK(a) value of 5.14, 6.76 and 9.08. The results obtained showed that the optimum pH values for adsorption were 6.0 for Cu(II), 7.0 for Cd(II) and 5.0 for Pb(II). The kinetics study demonstrated that the adsorption process proceeded according to the pseudo-second-order model. Three isotherm models (Langmuir, Freundlich and Dubinin-Radushkevich) were employed in the analysis of the adsorption equilibrium data. The Langmuir model resulted in the best fit and the new adsorbent had maximum adsorption capacities for Cu(II), Cd(II) and Pb(II) ions of 130.72, 83.75 and 166.94 mg g(-1), respectively. Desorption studies revealed that HNO(3) and HCl were the best eluents for desorption of Cu(II), Cd(II) and Pb(II) ions from the crosslinked chitosan.

Microwave irradiation-assisted synthesis of a novel crown ether crosslinked chitosan as a chelating agent for heavy metal ions (M(+n))

Microwave irradiation was used to obtain a di-Schiff base type crosslinked chitosan dibenzocrown ether (CCdBE) via the reaction between the -NH(2) and -CHO groups in chitosan and 4,4'-diformyldibenzo-18-c-6, respectively. The structure of the synthesized compound was characterized by elemental analysis, solid state 13C-NMR and FT-IR spectra analysis. The results showed that the mass fraction of nitrogen in the CCdBE derivative was much lower than those of chitosan. The FT-IR spectra of CCdBE revealed the expected chitosan-crown ether structure, as evidenced by the presence of the characteristic C=N and Ar peaks. The adsorption properties of CCdBE for Pd2+ and Hg2+ were investigated and the results demonstrated that the adsorbent has both desirable adsorption properties with a high particular adsorption selectivity for Hg2+ when in the presence of Pb2+ as well as selectivity coefficients for metal ions of K(Hg(2+)/Pb(2+)) = 8.00 and K(Hg(2+)/Pb(2+)) = 10.62 at pH values of 4 and 6, respectively. The reusability tests for CCdBE for Pb2+ adsorption showed that complete recovery of the ion was possible with CCdBE after 10-multiple reuses while CTS had no reusability at acidic solution because of its higher dissolution. The studied features of CCdBE suggested that the material could be considered as a new adsorbent. It is envisaged that the crosslinking of CTS into CCdBE would enhance practicality and effectiveness of adsorption in ion separation and removal procedures.

Adsorption of Cu(II), Co(II), and Ni(II) ions by modified magnetic chitosan chelating resin

Cross-linked magnetic chitosan-isatin Schiff's base resin (CSIS) was prepared for adsorption of metal ions. CSIS obtained was investigated by means of FTIR, (1)H NMR, wide-angle X-ray diffraction (WAXRD), magnetic properties and thermogravimetric analysis (TGA). The adsorption properties of cross-linked magnetic CSIS resin toward Cu(2+), Co(2+) and Ni(2+) ions were evaluated. Various factors affecting the uptake behavior such as contact time, temperature, pH and initial concentration of the metal ions were investigated. The kinetic parameters were evaluated utilizing the pseudo-first-order and pseudo-second-order. The equilibrium data were analyzed using the Langmuir, Freundlich, and Tempkin isotherm models. The adsorption kinetics followed the mechanism of the pseudo-second-order equation for all systems studied, evidencing chemical sorption as the rate-limiting step of adsorption mechanism and not involving a mass transfer in solution. The best interpretation for the equilibrium data was given by Langmuir isotherm, and the maximum adsorption capacities were 103.16, 53.51, and 40.15mg/g for Cu(2+), Co(2+) and Ni(2+) ions, respectively. Cross-linked magnetic CSIS displayed higher adsorption capacity for Cu(2+) in all pH ranges studied. The adsorption capacity of the metal ions decreased with increasing temperature. The metal ion-loaded cross-linked magnetic CSIS were regenerated with an efficiency of greater than 88% using 0.01-0.1M ethylendiamine tetraacetic acid (EDTA).

Study on silk sericin and chitosan blend film: morphology and secondary structure characterizations

This study aimed to prepare and characterize silk sericin and chitosan blend film as well as the native silk sericin and chitosan films. The films were observed their morphology using Scanning Electron Microscope (SEM). The secondary structures of the films were analyzed using Fourier Transform Infrared (FTIR) spectroscopy. Transparency of the films was investigated with UV-visible spectroscopy. The results found that all of silk films were smooth throughout the film surfaces, including blend film. This showed that silk sericin and chitosan very well compatible. However, phase separation is also being observed. It is show that the interaction between two materials might be miscible together. The FTIR results indicated that the most of films were composed both in random coil and beta-sheet forms which predominantly of the random coil structures. The results suggesting the blend film between sericin and chitosan did not change the intramolecular structure when compared to the native films. The silk sericin and blend films were slightly yellowish color and were higher transparent than chitosan film. However, % transmittance at lamda max of 660 nm showed that all of films have similar values. The result suggested that the transparency of the film did not change even blend together. It is a promising that both silk sericin and chitosan would be blended into many forms for applications in specifically fields.

Selective removal of mercury(II) from wastewater using polythioamides

The potential and feasibility of polythioamides as Hg(II) sorbents were evaluated. Powdered polythioamides quantitatively sorbed Hg(II) from an aqueous solution at pH 1-8. The sorption of Hg(II) on polythioamides obeyed the Langmuir adsorption isotherm; the sorption capacity was 0.70-0.85 g-Hgg(-1). Hg(II) was selectively separated from solutions containing 500 times larger amounts of Mn(II), Fe(III), Cu(II), Zn(II), and Pb(II) at pH 1. The tertiary polythioamide (PTA1) is soluble in chloroform and can be readily coated on a commercially available polymer resin, Amberlite XAD7HP. PTA1-coated resin as well as powdered PTA1 were applicable to the selective removal of Hg(II) from real wastewater.

Removal of Cu(II) from aqueous solutions using chemically modified chitosan

Chemically modified chitosan namely epichlorohydrin cross-linked xanthate chitosan (ECXCs) has been used for the removal of Cu(II) ions from aqueous medium. The influence of various operating parameters such as pH, temperature, sorbent dosage, initial concentration of Cu(II) ions and contact time on the adsorption capacity of ECXCs has been investigated. Thermodynamic parameters namely Delta G degrees, Delta H degrees and DeltaS degrees of the Cu(II) adsorption process have been calculated. Differential anodic stripping voltammetric technique was used to determine the concentration of Cu(II) in the test solution before and after adsorption. The nature of the possible adsorbent-metal ion interactions was studied by Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. The studies showed that the adsorption of Cu(II) on ECXCs strongly depends on pH and temperature. The maximum adsorption capacity was observed at pH 5.0 and the adsorption capacity of ECXCs increased with increasing temperature indicating the endothermic nature of adsorption process. Langmuir and Freundlich adsorption equations were used to fit the experimental data. The adsorption process is found to follow the pseudo-second-order kinetic model. The maximum adsorption capacity was found to be 43.47 mg g(-1) from the Langmuir isotherm model at 50 degrees C. During desorption studies 97-100% of adsorbed copper ion is released into solution in presence of 1N EDTA, HCl and H(2)SO(4).

Adsorptive removal of Congo red, a carcinogenic textile dye, from aqueous solutions by maghemite nanoparticles

The adsorption of Congo red (CR) onto maghemite nanoparticles (gamma-Fe(2)O(3)) and its desorption was investigated. The adsorption capacity was evaluated using both the Langmuir and Freundlich adsorption isotherm models. Maghemite nanoparticles (gamma-Fe(2)O(3)) were prepared easily in a surfactant-less microemulsion by co-precipitation method. The size of the produced maghemite nanoparticles was determined by X-ray diffraction (XRD) analysis and scanning electron microscopy (SEM). Synthesized maghemite nanoparticles showed the highest adsorption capacities of CR compared to many other adsorbents and would be a good method to increase adsorption efficiency for the removal of CR in a wastewater treatment process. The maximum adsorption occurred at pH 5.9. The Langmuir adsorption capacity (q(max)) was found to be 208.33 mg g(-1) of the adsorbent.

Adsorption behaviors of Hg(II) on chitosan functionalized by amino-terminated hyperbranched polyamidoamine polymers

The adsorption behaviors of Hg(II) on adsorbents, chitosan functionalized by generation 1.0-3.0 of amino-terminated hyperbranched polyamidoamine polymers (denoted as CTS-1.0, CTS-2.0 and CTS-3.0, respectively), were studied. The optimum pH corresponding to the maximum adsorption capacities was found to be 5.0 for the three adsorbents. The experimental equilibrium data of Hg(II) on the three adsorbents were fitted to the Freundlich and the Langmuir models, and it is found that the Langmuir isotherm was the best fitting model to describe the equilibrium adsorption. The kinetics data indicated that the adsorption process of Hg(II) ions on CTS-1.0, CTS-2.0 and CTS-3.0 were governed by the film diffusion and followed pseudo-second-order rate model. Thermodynamic analysis and FTIR analysis revealed that the adsorption behaviors of Hg(II) ions on the three adsorbents could be considered as spontaneous, endothermic and chemical sorption process, resulting in their higher adsorption capacities at higher temperature.

Adsorption of platinum(IV) and palladium(II) from aqueous solution by thiourea-modified chitosan microspheres

The chitosan microparticles were prepared using the inverse phase emulsion dispersion method and modified with thiourea (TCS). TCS was characterized by scanning electron microscope (SEM), the Fourier transform infrared (FT-IR) spectra, sulfur elemental analysis, specific surface area and pore diameter. The effects of various parameters, such as pH, contact time, initial concentration and temperature, on the adsorption of Pt(IV) and Pd(II) by TCS were investigated. The results showed that the maximum adsorption capacity was found at pH 2.0 for both Pt(IV) and Pd(II). TCS can selectively adsorb Pt(IV) and Pd(II) from binary mixtures with Cu(II), Pb(II), Cd(II), Zn(II), Ca(II), and Mg(II). The adsorption reaction followed the pseudo-second-order kinetics, indicating the main adsorption mechanism of chemical adsorption. The isotherm adsorption equilibrium was well described by Langmuir isotherms with the maximum adsorption capacity of 129.9 mg/g for Pt(IV) and 112.4 mg/g for Pd(II). The adsorption capacity of both Pt(IV) and Pd(II) decreased with temperature increasing. The negative values of enthalpy (DeltaH degrees ) and Gibbs free energy (DeltaG degrees ) indicate that the adsorption process is exothermic and spontaneous in nature. The adsorbent was stable without loss of the adsorption capacity up to at least 5 cycles and the desorption efficiencies were above 95% when 0.5 M EDTA-0.5M H2SO4 eluent was used. The results also showed that the preconcentration factor for Pt(IV) and Pd(II) was 196 and 172, respectively, and the recovery was found to be more than 97% for both precious metal ions.

Equilibrium and kinetic studies on free cyanide adsorption from aqueous solution by activated carbon

Adsorption equilibrium and kinetics of free cyanide onto activated carbon were investigated in the batch tests, and the effects of contact time (1-72 h) and initial cyanide concentrations in the range of 102-532 mg/L were studied. Linear regression was used to determine the best fit of equilibrium and kinetics expressions. The two-parameter models including Freundlich, Dubinin-Radushkevich, Temkin and four different linearized forms of Langmuir and three-parameter models including Redlich-Peterson and Koble-Corrigan were employed for fitting the equilibrium data and it was found that, three-parameter models fitted the data better than the two-parameter models and among the three-parameter models the equilibrium data are best represented by Koble-Corrigan model. A number of kinetic models including fractional power, zero order, first order, pseudo-first order, Elovich, second order, intraparticle diffusion and four different linearized forms of pseudo-second order models were tested to fit the kinetic data. The latter was found to be consistent with the data. Intraparticle diffusion plots show that the adsorption process of free cyanide is a two steps process. In the first step, the adsorption of cyanide is fast while in the second step, cyanide adsorption slows down.

Influence of Philosamia ricini silk fibroin components on morphology, secondary structure and thermal properties of chitosan biopolymer film

This study aimed to prepare Eri (Philosamia ricini) Silk Fibroin (SF)/chitosan (CS) blend films by a solvent evaporation method and to compare the blend films with both native SF and CS films. Influence of SF ratios on the morphology, secondary structure and thermal decomposition of the CS blend films were investigated. The native SF and CS films were uniform and homogeneous without phase separation. For the blend films, the uniform can be found less than 60% of SF composition. All of SF/CS blend films showed both SF and CS characteristics. FT-IR results showed that the blend films composed of both random coil and beta-sheet with predominant of beta-sheet form. Interaction of intermolecular between SF and CS have occurred which were measured by thermogravimetric thermograms. Increasing of SF contents was leading to the increase of beta-sheet structures which were enhanced the thermal stability of the CS blend films.

Removal of toxic metal ions with magnetic hydrogels

Hydrogels, based on 2-acrylamido-2-methyl-1-propansulfonic acid (AMPS) were synthesized via photopolymerization technique and used for the preparation of magnetic responsive composite hydrogels. These composite hydrogels with magnetic properties were further utilized for the removal of toxic metal ions such as Cd(II), Co(II), Fe(II), Pb(II), Ni(II), Cu(II) and Cr(III) from aqueous environments. It was revealed that hydrogel networks with magnetic properties can effectively be utilized in the removal of pollutants. The results verified that magnetic iron particle containing p(AMPS) hydrogel networks provide advantageous over conventional techniques. Langmuir and Freundlich adsorption isotherms were applied for toxic metal removal and both isotherms were fit reasonably well for the metal ion absorptions.

Ethylenesulfide as a useful agent for incorporation into the biopolymer chitosan in a solvent-free reaction for use in cation removal

Chitosan (Ch) was chemically modified with ethylenesulfide (Es) under solvent-free conditions to give (ChEs), displaying a high content of thiol groups due to opening of the three member cyclic reagent. Elemental analysis showed a decrease in nitrogen content. This result indicated the incorporation of two ethylenesulfide molecules for each unit of the polymeric structure of the precursor biopolymer. Infrared spectroscopy, thermogravimetry, and (13)C NMR in the solid state demonstrated the effectiveness of the reaction, with signals at 30 ppm for ChEs due to the change in the methylene group environment. Divalent metal uptake by chemically modified biopolymer gave the order Cu>Ni>Co>Zn, reflecting the corresponding acidity of these cations in bonding to the sulfur and the basic nitrogen atoms available on the pendant chains. The equilibrium data were fitted to Freundlich, Temkin, and Langmuir models. The maximum monolayer adsorption capacity for the cations was found to be 1.54+/-0.02, 1.25+/-0.03, 1.13+/-0.01, and 0.83+/-0.03 mmol g(-1), respectively. The Langmuir model best explained the cation-sulfur bond interactions at the solid-liquid interface. The thermodynamics for these interactions gave exothermic enthalpic values of -43.02+/-0.03, -28.72+/-0.02, -26.27+/-0.04, and -17.32+/-0.02 kJ mol(-1), respectively. The spontaneity of the systems is given by negative Gibbs free energies of -31.2+/-0.1, -32.7+/-0.1, -31.7+/-0.1, and -32.2+/-0.1 kJ mol(-1), respectively, in spite of the unfavorable negative entropic values of -39+/-1, -13+/-1, -18+/-1, and -49+/-1 J K(-1)mol(-1) due to solvent ordering in the course of complexation. This newly synthesized biopolymer is presented as a chemically useful material for cation removal from aqueous solution.