Polymer Membrane Ion-Selective Electrodes-What are the Limits?

Reconfiguration of organic electrochemical transistors for high-accuracy potentiometric sensing

Organic electrochemical transistors have emerged as a promising alternative to traditional 2/3 electrode setups for sensing applications, offering in-situ transduction, electrochemical amplification, and noise reduction. Several of these devices are designed to detect potentiometric-derived signals. However, potentiometric sensing should be performed under open circuit potential conditions, allowing the system to reach thermodynamic equilibrium. This criterion is not met by conventional organic electrochemical transistors, where voltages or currents are directly applied to the sensing interface, that is, the gate electrode. In this work, we introduce an organic electrochemical transistor sensing configuration called the potentiometric‑OECT (pOECT), which maintains the sensing electrode under open circuit potential conditions. The pOECT exhibits a higher response than the 2-electrode setup and offers greater accuracy, response, and stability compared to conventional organic electrochemical transistors. Additionally, it allows for the implementation of high-impedance electrodes as gate/sensing surfaces, all without compromising the overall device size.

Ion-Selective Electrode for Nitrates Based on a Black PCV Membrane

Carbon nanomaterials were introduced into this research as modifiers for polymeric membranes for single-piece electrodes, and their properties were studied for the case of nitrate-selective sensors. The use of graphene, carbon black and carbon nanotubes is shown to significantly improve the potentiometric response, while no redox response was observed. The use of carbon nanomaterials results in a near-Nernstian response (54 mV/pNO3-) towards nitrate ions over a wide linear range (from 10-1 to 10-6 M NO3-). The results obtained by chronopotentiometry and electrochemical impedance spectroscopy reveal little resistance, and the capacitance parameter is as high as 0.9 mF (for graphene-based sensor). The high electrical capacity of electrodes results in the good stability of the potentiometric response and a low potential drift (0.065 mV/h). Introducing carbon nanomaterials into the polymetric membrane, instead of using them as separate layers, allows for the simplification of the sensors' preparation procedure. With single-piece electrodes, one step of the procedure could be omitted, in comparison to the procedure for the preparation of solid-contact electrodes.

Nonequilibrium Anion Detection in Solid-Contact Ion-Selective Electrodes

Low-cost and portable nitrate and phosphate sensors are needed to improve farming efficiency and reduce environmental and economic impact arising from the release of these nutrients into waterways. Ion selective electrodes (ISEs) could provide a convenient platform for detecting nitrate and phosphate, but existing ionophore-based nitrate and phosphate selective membrane layers used in ISEs are high cost, and ISEs using these membrane layers suffer from long equilibration time, reference potential drift, and poor selectivity. In this work, we demonstrate that constant current operation overcomes these shortcomings for ionophore-based anion-selective ISEs through a qualitatively different response mechanism arising from differences in ion mobility rather than differences in ion binding thermodynamics. We develop a theoretical treatment of phase boundary potential and ion diffusion that allows for quantitative prediction of electrode response under applied current. We also demonstrate that under pulsed current operation, we can create functional solid-contact ISEs using lower-cost molecularly imprinted polymers (MIPs). MIP-based nitrate sensors provide comparable selectivity against chloride to costlier ionophore-based sensors and exhibit >100,000 times higher selectivity against perchlorate. Likewise, MIP-based solid contact ion-selective electrode phosphate sensors operated under pulsed current provide competitive selectivity against chloride, nitrate, perchlorate, and carbonate anions. The theoretical treatment and conceptual demonstration of pulsed-current ISE operation we report will inform the development of new materials for membrane layers in ISEs based on differences in ion mobility and will allow for improved ISE sensor designs.

Polymeric membrane potentiometric antibiotic sensors using computer-aided screening of supramolecular macrocyclic carriers

Carrier-based polymeric membrane potentiometric sensors are an ideal tool for detecting ionic species. However, in the fabrication of these sensors, the screening of carriers still relies on empirical trial- and error-based optimization, which requires tedious and time-consuming experimental verification. In this work, computer-aided screening of carriers is applied in the preparation of polymeric membrane potentiometric sensors. Molecular docking is used to study the host-guest interactions between receptors and targets. Binding energies are employed as the standard to screen the appropriate carrier. As a proof-of-concept experiment, the antibiotic ciprofloxacin is selected as the target model. A series of supramolecular macrocyclic receptors including cyclodextrins, cucurbiturils and calixarenes are chosen as potential receptors. The proposed sensor based on the receptor calix[4]arene screened by molecular docking shows a lower detection limit of 0.5 μmol L-1 for ciprofloxacin. It can be expected that the proposed computer-aided screening technique of carriers can provide a simple but highly efficient method for the fabrication of carrier-based electrochemical and optical sensors.

Covalently attached ionophores extend the working range of potentiometric pH sensors with poly(decyl methacrylate) sensing membranes

The pH working range of solid-contact ion-selective electrodes (ISEs) with plasticizer-free poly(decyl methacrylate) sensing membranes is shown to be expanded by covalent attachment of H+ ionophores to the polymeric membrane matrix. In situ photopolymerization not only incorporates the ionophores into the polymer backbone, but at the same time also attaches the sensing membranes covalently to the underlying inert polymer and nanographite solid contact, minimizing sensor drift and preventing failure by membrane delamination. A new pyridine-based H+ ionophore, 3-(pyridine-3-yl)propyl methacrylate, has lower basicity than trialkylamine ionophores and expands the upper detection limit. This reduces in particular the interference from hydrogen phthalate, which is a common component of commercial pH buffers. Moreover, the lower detection limit is improved by replacing the CH2CH2 spacer of previously reported dialkylaminoethyl methacrylates with a (CH2)10 spacer, which increases its basicity. Notably, for the more basic and highly cation-selective ionophore 10-(diisopropylamino)decyl methacrylate, the extent of counterion interference from hydrogen phthalate shifted the upper detection limit to lower pH by nearly one pH unit when the crosslinker concentration was decreased.

Sensing and extraction of hazardous metals by di-phosphonates of heterocycles: a combined experimental and theoretical study

In this study, pyridine and phenanthroline diphosphonate ligands were investigated for the first time from the context of solvent extraction and potentiometric sensing of Co(II), Ni(II), Cu(II), Zn(II), Cd(II), and Pb(II) cations. The extraction efficiency under the same conditions for phenanthroline-diphosphonates is considerably higher than that for pyridine ligands. At the same time, the pyridine-diphosphonates show pronounced selectivity towards lead in this metal series. The extraction systems with phenanthroline diphosphonates provided the most efficient extraction of Cd(II) and Pb(II) cations (D > 90). The newly developed pyridine and phenanthroline diphosphonate ligands have proven to be highly effective components in plasticized polymeric membranes. These ligands can be utilized to construct potentiometric ion sensors that exhibit a notable response specifically towards Pb(II) cations. Among the previously reported tetradentate ligands, the phenanthroline diphosphonate ligand, when incorporated into plasticized polymeric membranes, demonstrated the highest sensitivity towards d-metals and Pb(II). The structure of the single crystal complex of Pb(II) and Cd(II) with pyridine-diphosphonates was studied by X-ray diffraction analysis (XRD). The geometry of Cu(II), Zn(II), Cd(II) and Pb(II) complexes and the energy effect of the complex formation, including pseudo-oligomerization reactions, were determined by DFT calculations. The high sensing and extraction efficiency of diphosphonates with respect to Pb(II) is consistent with the minimum values of complex formation energies. The variation in sensory and extraction properties observed among the studied diphosphonate ligands is influenced by the ability to form polynuclear complexes with Pb(II) cations, whereas such properties are absent in the case of Cd(II) cations.

Ion-Selective Electrodes with Solid Contact Based on Composite Materials: A Review

Potentiometric sensors are the largest and most commonly used group of electrochemical sensors. Among them, ion-selective electrodes hold a prominent place. Since the end of the last century, their re-development has been observed, which is a consequence of the introduction of solid contact constructions, i.e., electrodes without an internal electrolyte solution. Research carried out in the field of potentiometric sensors primarily focuses on developing new variants of solid contact in order to obtain devices with better analytical parameters, and at the same time cheaper and easier to use, which has been made possible thanks to the achievements of material engineering. This paper presents an overview of new materials used as a solid contact in ion-selective electrodes over the past several years. These are primarily composite and hybrid materials that are a combination of carbon nanomaterials and polymers, as well as those obtained from carbon and polymer nanomaterials in combination with others, such as metal nanoparticles, metal oxides, ionic liquids and many others. Composite materials often have better mechanical, thermal, electrical, optical and chemical properties than the original components. With regard to their use in the construction of ion-selective electrodes, it is particularly important to increase the capacitance and surface area of the material, which makes them more effective in the process of charge transfer between the polymer membrane and the substrate material. This allows to obtain sensors with better analytical and operational parameters. Brief characteristics of electrodes with solid contact, their advantages and disadvantages, as well as research methods used to assess their parameters and analytical usefulness were presented. The work was divided into chapters according to the type of composite material, while the data in the table were arranged according to the type of ion. Selected basic analytical parameters of the obtained electrodes have been collected and summarized in order to better illustrate and compare the achievements that have been described till now in this field of analytical chemistry, which is potentiometry. This comprehensive review is a compendium of knowledge in the research area of functional composite materials and state-of-the-art SC-ISE construction technologies.

The New Reliable pH Sensor Based on Hydrous Iridium Dioxide and Its Composites

The new reliable sensor for pH determination was designed with the use of hydrous iridium dioxide and its composites. Three different hIrO2-based materials were prepared and applied as solid-contact layers in pH-selective electrodes with polymeric membrane. The material choice included standalone hydrous iridium oxide; composite material of hydrous iridium oxide, carbon nanotubes, and triple composite material composed of hydrous iridium oxide; carbon nanotubes; and poly(3-octylthiophene-2,5-diyl). The paper depicts that the addition of functional material to standalone metal oxide is beneficial for the performance of solid-state ion-selective electrodes and presents the universal approach to designing this type of sensors. Each component contributed differently to the sensors' performance-the addition of carbon nanotubes increased the electrical capacitance of sensor (up to 400 µF) while the addition of conducting polymer allowed it to increase the contact angle of material changing its wetting properties and enhancing the stability of potentiometric response. Hydrous iridium oxide contacted electrodes exhibit linear response in wide linear range of pH (2-11) and stable potentiometric response (the lowest potential drift of 0.036 mV/h is attributed to the electrode with triple composite material).

Recent Advances in Wearable Potentiometric pH Sensors

Wearable sensors reflect the real-time physiological information and health status of individuals by continuously monitoring biochemical markers in biological fluids, including sweat, tears and saliva, and are a key technology to realize portable personalized medicine. Flexible electrochemical pH sensors can play a significant role in health since the pH level affects most biochemical reactions in the human body. pH indicators can be used for the diagnosis and treatment of diseases as well as the monitoring of biological processes. The performances and applications of wearable pH sensors depend significantly on the properties of the pH-sensitive materials used. At present, existing pH-sensitive materials are mainly based on polyaniline (PANI), hydrogen ionophores (HIs) and metal oxides (MOx). In this review, we will discuss the recent progress in wearable pH sensors based on these sensitive materials. Finally, a viewpoint for state-of-the-art wearable pH sensors and a discussion of their existing challenges are presented.

Wearable microfluidic-based e-skin sweat sensors

Electronic skins (e-skins) are soft (deformable and stretchable) state-of-the-art wearable devices that emulate the attributes of human skin and act as a Human-Machine Interface (HMI). Recent advances in e-skin for real-time detection of medical signals such as pulse, temperature, electromyogram (EMG), electroencephalogram (EEG), electrooculogram (EOG), electrocardiogram (ECG), and other bioelectric signals laid down an intelligent foundation for early prediction and diagnosis of diseases with a motive of reducing the risk of the ailment reaching to the end stage. In particular, sweat testing has been employed in diverse applications ranging from medical diagnosis of diabetes, cystic fibrosis, tuberculosis, blood pressure, and autonomic neuropathy to evaluating fluid and electrolyte balance in athletes. Typically, sweat testing techniques are done by trained experts and require off-body measurements, which prevent individuals from de-coding health issues quickly and independently. With the onset of soft electronics, wearable sweat sensors overcome this disadvantage via in situ sweat measurements with real-time feedback, timely diagnosis, creating the potential for preventive care and treatment. Over the past few decades, wearable microfluidic-based e-skin sweat sensors have paved a new way, promising sensing interfaces that are highly compatible with arranging medical and electronic applications. The present review highlights the recent research carried out in the microfluidic-based wearable sweat sensors with a critical focus on real-time sensing of lactate, chloride, and glucose concentration; sweat rate, simultaneously with pH, and total sweat loss for preventive care, timely diagnosis, and point-of-care health and fitness monitoring.

Continuous and Polarization-Tuned Redox Capacitive Anion Sensing at Electroactive Interfaces

Continuous, real-time ion sensing is of great value across various environmental and medical scenarios but remains underdeveloped. Herein, we demonstrate the potential of redox capacitance spectroscopy as a sensitive and highly adaptable ion sensing methodology, exemplified by the continuous flow sensing of anions at redox-active halogen bonding ferrocenylisophthalamide self-assembled monolayers. Upon anion binding, the redox distribution of the electroactive interface, and its associated redox capacitance, are reversibly modulated, providing a simple and direct sensory readout. Importantly, the redox capacitance can be monitored at a freely chosen, constant electrode polarization, providing a facile means of tuning both the sensor analytical performance and the anion binding affinity, by up to 1 order of magnitude. In surpassing standard voltammetric methods in terms of analytical performance and adaptability, these findings pave the way for the development of highly sensitive and uniquely tunable ion sensors. More generally, this methodology also serves as a powerful and unprecedented means of simultaneously modulating and monitoring the thermodynamics and kinetics of host-guest interactions at redox-active interfaces.

Real-time Voltammetric Anion Sensing Under Flow*

The development of real‐life applicable ion sensors, in particular those capable of repeat use and long‐term monitoring, remains a formidable challenge. Herein, we demonstrate, in a proof‐of‐concept, the real‐time voltammetric sensing of anions under continuous flow in a 3D‐printed microfluidic system. Electro‐active anion receptive halogen bonding (XB) and hydrogen bonding (HB) ferrocene‐isophthalamide‐(iodo)triazole films were employed as exemplary sensory interfaces. Upon exposure to anions, the cathodic perturbations of the ferrocene redox‐transducer are monitored by repeat square‐wave voltammetry (SWV) cycling and peak fitting of the voltammograms by a custom‐written MATLAB script. This enables the facile and automated data processing of thousands of SW scans and is associated with an over one order‐of‐magnitude improvement in limits of detection. In addition, this improved analysis enables tuning of the measurement parameters such that high temporal resolution can be achieved. More generally, this new flow methodology is extendable to a variety of other analytes, including cations, and presents an important step towards translation of voltammetric ion sensors from laboratory to real‐world applications.

An all-solid-state NO3- ion-selective electrode with gold nanoparticles solid contact layer and molecularly imprinted polymer membrane

To improve the single-layer all-solid-state ion selective electrode' defects including poor conductivity of PVC sensitive membrane and interference of water layer between substrate electrode and sensitive membrane, a double-layer all-solid-state ion selective electrode with nanomaterial as the solid contact layer and conductive polymer as the ion sensitive membrane was developed. A gold nanoparticles solid contact layer and a nitrate-doped polypyrrole molecularly imprinted polymer membrane were prepared by electrodeposition. The optimal parameters obtained by electrochemical performance test were 2.5 mmol/L HAuCl4 electrolyte for solid contact layer and 1800s electrodeposition time for sensitive membrane. The new electrode exhibited a Nernstian response of -50.4 mV/decade and a low detection limit of 5.25×10-5mol/L. Potentiometric water layer test showed no water film formed between the gold nanoparticles solid contact layer and nitrate-doped polypyrrole molecularly imprinted polymer membrane. The contact angle between droplet and the surface of solid contact layer was 112.35° and showed good hydrophobic property. Furthermore, the developed electrode exhibited fast response, excellent potential stability and long lifetime. This electrode is suitable for the detection of nitrate concentration in water and liquid fertilizer.

Real-time in situ auto-correction of K+ interference for continuous and long-term NH4+ monitoring in wastewater using solid-state ion selective membrane (S-ISM) sensor assembly

Potassium ions (K⁺) present in wastewater has caused severe interference for NH₄⁺ monitoring, over-estimation of NH₄⁺ concentration and ultimately leads to extra energy consumption. Past effort for enhancing the selectivity of NH₄⁺ over K⁺ were oftentimes complex, costly, or compromised the selectivity and accuracy of the NH₄⁺ ion selective membrane (ISM) sensors. This study targeted this imminent challenge by developing an integrated NH₄⁺/K⁺ auto-correction solid-state ISM (S-ISM) sensor assembly combined with a data-driven model to monitor [NH₄⁺] under different [NH₄⁺] and [K⁺] concentrations. The results showed that the interference of K⁺ was substantially alleviated for NH₄⁺ measurement. The accuracy was enhanced by over 70% when examined using real wastewater and energy consumption was expected to reduce by 26% for a wastewater treatment plant, especially for wastewater with high [K⁺]. Furthermore, the uniquely structured S-ISMs were made by embedding the ionophores in a robust polyvinyl chloride (PVC) matrix containing plasticizers and a layer of carbon nanotubes (CNT) as ion-to-electron transducer, which maintained the selectivity and accuracy of the S-ISM sensor for 4 weeks in wastewater. NH₄⁺/K⁺ sensor assembly integrated with data-driven correction models poses great potential in high-efficiency and energy-saving wastewater treatment and water reuse processes.

Phase-dependent ion-to-electron transducing efficiency of WS2 nanosheets for an all-solid-state potentiometric calcium sensor

Ultrathin metallic WS₂ (M-WS₂) nanosheets and semiconductive WS₂ (S-WS₂) nanosheets were exfoliated and for the first time employed as ion-to-electron transducing layer to construct an all-solid-state ion-selective electrode. Importantly, we found that the transducing efficiency of WS₂ nanosheet-based solid-contact layer is phase-dependent. The M-WS₂ nanosheets with larger content of 1 T-phase structure exhibit higher transducing efficiency than S-WS₂ nanosheets, which can be ascribed to the remarkable conductivity of M-WS₂ nanosheets. In order to demonstrate the excellent properties of the M-WS₂ nanosheet-based tranducing layer, an all-solid-state calcium ion potentiometric sensor was constructed as the model. As expected, a Nernstian response (27.41 mV per decade, R² = 0.9998) with a wide linear range of 1.0 × 10^-5.0 to 1.0 × 10^-2.0 M and a limit of detection of 2.0 μM was obtained. The developed all-solid-state potentiometric sensor using M-WS₂ nanosheets as ion-to-electron transducing layer is expected to bring new progress for routine detection in various fields. Graphical Abstract Schematic illustration of the introduction of WS₂ nanosheets with different phase structures as a new-generation solid-contact ion-to-electron transducing layer for all-solid-state potentiometric sensors.

Solid-Contact Ion-Selective and Reference Electrodes Covalently Attached to Functionalized Poly(ethylene terephthalate)

Numerous ion-selective and reference electrodes have been developed over the years. Following the need for point-of-care and wearable sensors, designs have transitioned recently from bulky devices with an aqueous inner filling solution to planarizable solid-contact electrodes. However, unless the polymeric sensing and reference membranes are held in place mechanically, delamination of these membranes from the underlying solid to which they adhere physically limits sensor lifetime. Even minor external mechanical stress or thermal expansion can result in membrane delamination and, thereby, device failure. To address this problem, we designed a sensing platform based on poly(ethylene terephthalate) substrates to which polyacrylate-based sensing and polymethacrylate-based reference membranes are attached covalently. Ion-selective membranes with covalently attached or freely dissolved ionophore- and ionic-liquid-doped reference membranes can be directly photopolymerized onto surface-functionalized poly(ethylene terephthalate), resulting in the formation of covalent bonds between the underlying substrate and the attached membranes. H⁺- and K⁺-selective electrodes thus prepared exhibit highly selective responses with the theoretically expected (Nernstian) response slope, and reference electrodes provide sample-independent reference potentials over a wide range of electrolyte concentrations. Even repeated mechanical stress does not result in the delamination of the sensing and reference membranes, leading to electrodes with much improved long-term performance. As demonstrated for poly(ethylene-co-cyclohexane-1,4-dimethanol terephthalate) (PETG), this approach may be expanded to a wide range of other polyester, polyamide, and polyurethane platform materials. Covalent attachment of sensing and reference membranes to an inert plastic platform material is a very promising approach to a problem that has plagued the field of ion-selective electrodes and field effect transistors for over 30 years.

Electrochemical Anion Sensing: Supramolecular Approaches

Anions play a vital role in a broad range of environmental, technological, and physiological processes, making their detection/quantification valuable. Electroanalytical sensors offer much to the selective, sensitive, cheap, portable, and real-time analysis of anion presence where suitable combinations of selective (noncovalent) recognition and transduction can be integrated. Spurred on by significant developments in anion supramolecular chemistry, electrochemical anion sensing has received considerable attention in the past two decades. In this review, we provide a detailed overview of all electroanalytical techniques that have been used for this purpose, including voltammetric, impedimetric, capacititive, and potentiometric methods. We will confine our discussion to sensors that are based on synthetic anion receptors with a specific focus on reversible, noncovalent interactions, in particular, hydrogen- and halogen-bonding. Apart from their sensory properties, we will also discuss how electrochemical techniques can be used to study anion recognition processes (e.g., binding constant determination) and will furthermore provide a detailed outlook over future efforts and promising new avenues in this field.

Recent advances in solid-contact ion-selective electrodes: functional materials, transduction mechanisms, and development trends

This article presents a comprehensive overview of recent progress in the design and applications of solid-contact ion-selective electrodes (SC-ISEs).

Cytotoxicity Study of Ionophore-Based Membranes: Toward On-Body and in Vivo Ion Sensing

We present the most complete study to date comprising in vitro cytotoxicity tests of ion-selective membranes (ISMs) in terms of cell viability, proliferation, and adhesion assays with human dermal fibroblasts. ISMs were prepared with different types of plasticizers and ionophores to be tested in combination with assays that focus on the medium-term and long-term leaching of compounds. Furthermore, the ISMs were prepared in different configurations considering (i) inner-filling solution-type electrodes, (ii) all-solid-state electrodes based on a conventional drop-cast of the membrane, (iii) peeling after the preparation of a wearable sensor, and (iv) detachment from a microneedle-based sensor, thus covering a wide range of membrane shapes. One of the aims of this study, other than the demonstration of the biocompatibility of various ISMs and materials tested herein, is to create an awareness in the scientific community surrounding the need to perform biocompatibility assays during the very first steps of any sensor development with an intended biomedical application. This will foster meeting the requirements for subsequent on-body application of the sensor and avoiding further problems during massive validations toward the final in vivo use and commercialization of such devices.

Gold Plate Electrodes Functionalized by Multiwall Carbon Nanotube Film for Potentiometric Thallium(I) Detection

Solid-contact potentiometric ion-selective electrodes (SC-ISEs) for thallium determination have been designed using multiwall carbon nanotubes (MWCNTs) as the ion-to-electron transducer. Dispersed MWCNTs were drop-casted over a gold plate electrode. Two different crown ethers were used in the sensing membrane for the recognition of thallium (I). Sensorsbased on dibenzo-18-crown-6 (DB18C6) as a neutral carrier and NaTPB as an anionic additive exhibited a near Nernstian response of 57.3 mV/decade towards Tl+ ions over the activity range 4.5 × 10-6-7.0 × 10-4 M, with a limit of detection of 3.2 × 10-7 M. The time required to achieve 95% of the steadyequilibrium potential was <10 s. The complex formation constant (log βML) between dibenzo-18-crown-6 and thallium (I) (i.e., 5.99) was measured using the sandwich membrane technique. The potential response was pH independent over the range 3.0-9.5. The introduction of MWCNTs as an electron-ion-transducer layer between gold plate and the sensing membrane lead to a smaller membrane resistance and a large double layer capacitance, which was proven using impedance spectra and chronopotentiometry (i.e., 114.9 ± 12 kΩ, 52.1 ± 3.3 pF, 200 ± 13.2 kΩ, and 50 ± 4.2 µF). Additionally, reduction ofthe water layer between the sensing membrane and the underlying conductor wastested. Thus, it is clear that MWCNTs can be used as a transducing layer in SC-ISEs. The proposed sensor was introduced as an indicator electrode for potentiometric titration of single and ternary mixtures of I-, Br-, and S2- anions.

Development of a nickel oxide/oxyhydroxide-modified printed carbon electrode as an all solid-state sensor for potentiometric phosphate detection

This work describes the preparation, characterization and use of a nickel oxide/oxyhydroxide-printed carbon electrode as an efficient potentiometric phosphate sensor.

Light-Addressable Ion Sensing for Real-Time Monitoring of Extracellular Potassium

We report here on a light addressable potassium (K⁺ ) sensor where light illumination of a semiconducting silicon electrode substrate results in a localized activation of the faradaic electrochemistry at the illuminated spot. This allows one, by electrochemical control, to oxidize surface bound ferrocene moieties that in turn trigger K⁺ transfer from the overlaid K⁺ -selective film to the solution phase. The resulting voltammetric response is shown to be K⁺ -selective, where peak position is a direct function of K⁺ activity at the surface of electrode. This concept was used to measure extracellular K⁺ concentration changes by stimulating living breast cancer cells. The associated decrease of intracellular K⁺ level was confirmed with a fluorescent K⁺ indicator. In contrast to light addressable potentiometry, the approach introduced here relies on dynamic electrochemistry and may be performed in tandem with other electrochemical analysis when studying biological events on the electrode.

Ion-Selective Electrodes for Detection of Lead (II) in Drinking Water: A Mini-Review

Despite the fact that the adverse health effects due to the intake of lead have been well studied and widely recognized, lead contamination in drinking water has been reoccurring worldwide, with some incidents escalating into a public drinking water crisis. As lead contamination is often related to lead-based pipes close to or inside homes, it is not realistic, at least in the near term, to remove and replace all lead connection pipes and lead-based plumbing. Effective monitoring of lead concentration at consumers’ water taps remains critical for providing consumers with first-hand information and preventing potential wide-spread lead contamination in drinking water. This review paper examines the existing common technologies for laboratory testing and on-site measuring of lead concentrations. As the conventional analytical techniques for lead detection require using expensive instruments, as well as a high time for sample preparation and a skilled operator, an emphasis is placed on reviewing ion-selective electrode (ISE) technology due to its superior performance, low cost, ease of use, and its promising potential to be miniaturized and integrated into standalone sensing units. In a holistic way, this paper reviews and discusses the background, different types of ISEs are reviewed and discussed, namely liquid-contact ISEs and solid-contact ISEs. Along with the potential opportunities for further research, the limitations and unique challenges of ISEs for lead detection are also discussed in detail.

Preparation of a Highly Conductive Seed Layer for Calcium Sensor Fabrication with Enhanced Sensing Performance

The seed layer plays a crucial role in achieving high electrical conductivity and ensuring higher performance of devices. In this study, we report fabrication of a solution-gated field-effect transistor (FET) sensor based on zinc oxide nanorods (ZnO NRs) modified iron oxide nanoparticles (α-Fe₂O₃ NPs) grown on a highly conductive sandwich-like seed layer (ZnO seed layer/Ag nanowires/ZnO seed layer). The sandwich-like seed layer and ZnO NRs modification with α-Fe₂O₃ NPs provide excellent conductivity and prevent possible ZnO NRs surface damage from low pH enzyme immobilization, respectively. The highly conductive solution-gated FET sensor employed the calmodulin (CaM) immobilization on the surface of α-Fe₂O₃-ZnO NRs for selective detection of calcium ions (Ca²⁺). The solution-gated FET sensor exhibited a substantial change in conductance upon introduction of different concentrations of Ca²⁺ and showed high sensitivity (416.8 μA cm^-2 mM^-1) and wide linear range (0.01-3.0 mM). In addition, the total Ca²⁺ concentration in water and serum samples was also measured. Compared to the analytically obtained data, our sensor was found to measure Ca²⁺ in the water and serum samples accurately, suggesting a potential alternative for Ca²⁺ determination in water and serum samples, specifically used for drinking/irrigation and clinical analysis.

A Fully Integrated Paper-Microfluidic Electrochemical Device for Simultaneous Analysis of Physiologic Blood Ions

A fully integrated paper microfluidic electrochemical device equipped with three different cation permeable films is developed to determine blood ions (Cl-, Na⁺, K⁺, and Ca2+) at a time. These blood ions that are normally dissolved in the real human blood stream are essential for cell metabolisms and homeostasis in the human body. Abnormal concentration of blood ions causes many serious disorders. The optimized microfluidic device working without any external power source can directly and effectively separate human blood components, and subsequently detect a specific blood ion with minimized interference. The measured sensitivity to Cl-, K⁺, Na⁺, and Ca2+ are -47.71, 45.97, 51.06, and 19.46 in mV decade-1, respectively. Potentiometric responses of the microfluidic devices to blood serum samples are in the normal ranges of each cation, and comparable with responses from the commercial blood ion analyzer Abbott i-Stat.