Bottom-Up Structuring and Site-Selective Modification of Hydrogels Using a Two-Photon [2+2] Cycloaddition of Maleimide

Coumarin-Based Photodegradable Hydrogels Enable Two-Photon Subtractive Biofabrication at 300 mm s-1

Spatiotemporally controlled two-photon photodegradation of hydrogels has gained increasing attention for high-precision subtractive tissue engineering. However, conventional photolabile hydrogels often have poor efficiency upon two-photon excitation in the near-infrared (NIR) region and thus require high laser dosage that may compromise cell activity. As a result, high-speed two-photon hydrogel erosion in the presence of cells remains challenging. Here we introduce the design and synthesis of efficient coumarin-based photodegradable hydrogels to overcome these limitations. A set of photolabile coumarin-functionalized polyethylene glycol linkers are synthesized through a Passerini multicomponent reaction. After mixing these linkers with thiolated hyaluronic acid, semi-synthetic photodegradable hydrogels are formed in situ via Michael addition crosslinking. The efficiency of photodegradation in these hydrogels is significantly higher than that in nitrobenzyl counterparts upon two-photon irradiation at 780 nm. A complex microfluidic network mimicking the bone microarchitecture is successfully fabricated in preformed coumarin hydrogels at high speeds of up to 300 mm s-1 and low laser dosage down to 10 mW. Further, we demonstrate fast two-photon printing of hollow microchannels inside a hydrogel to spatiotemporally direct cell migration in 3D. Collectively, these hydrogels may open new avenues for fast laser-guided tissue fabrication at high spatial resolution.

Instant Adhesion of Amyloid-like Nanofilms with Wet Surfaces

The adhesion and modification of wet surfaces by an interfacial adlayer remain a key challenge in chemistry and materials science. Herein, we report a transparent and biocompatible amyloid-like nanofilm that breaks through the hydration layer of a wet surface and achieves strong adhesion with a hydrogel/tissue surface within 2 s. This process is facilitated by fast amyloid-like protein aggregation at the air/water interface and the resultant exposure of hydrophobic groups. The resultant protein nanofilm adhered to a hydrogel surface presents an adhesion strength that is 20 times higher than the maximum friction force between the upper eyelid and eyeball. In addition, the nanofilm exhibits controllable tunability to encapsulate and release functional molecules without significant activity loss. As a result, therapeutic contact lenses (CLs) could be fabricated by adhering the functionalized nanofilm (carrying drug) on the CL surface. These therapeutic CLs display excellent therapeutic efficacy, showing an increase in cyclosporin A (CsA) bioavailability of at least 82% when compared to the commercial pharmacologic treatment for dry eye syndrome. Thus, this work underlines the finding that the bioinspired amyloid-like aggregation of proteins at interfaces drives instant adhesion onto a wet surface, enabling the active loading and controllable release of functional building blocks.

Controlling Properties and Functions of Polymer Gels Using Photochemical Reactions

Photoresponsive polymer gels have attracted increasing interest owing to their potential applications in healable materials, drug release systems, and extracellular matrices. Because polymer gels provide suitable environments for photochemical reactions, their properties and functions can be controlled with light with a high spatiotemporal resolution. Herein, the design of photoresponsive polymer gels based on different types of photochemical reactions is introduced. The mechanism and applications of irreversible photoreactions, such as photoinduced free-radical polymerization, photoinduced click reactions, and photolysis, as well as reversible photoreactions such as photoinduced reversible cycloadditions, reversible photosubstitution of metal complexes, and photoinduced metathesis are reviewed. The remaining challenges of photoresponsive polymer gels are also discussed.

Nanoporous aluminum oxide micropatterns prepared by hydrogel templating

Micropatterned nanoporous aluminum oxide arrays are prepared on silicon wafer substrates by using photopolymerized poly(dimethylacrylamide) hydrogels as porogenic matrices. Hydrogel micropatterns are fabricated by spreading the prepolymer mixture on the substrate, followed by UV photopolymerization through a micropatterned mask. The hydrogel is covalently bonded to the substrate surface. Al₂O₃ is produced by swelling the hydrogel in a saturated aluminum nitrate solution and subsequent thermal conversion/calcination. As a result, micropatterned porous Al₂O₃ microdots with heights in µm range and large specific surface areas up to 274 m² g^-1 are obtained. Hence, the hydrogel fulfills a dual templating function, namely micropatterning and nanoporosity generation. The impact of varying the photopolymerization time on the properties of the products is studied. Samples are characterized by light and confocal laser scanning microscopy, scanning electron microscopy, energy-dispersive x-ray spectrometry, and Kr physisorption analysis.

Advanced Bottom-Up Engineering of Living Architectures

Bottom-up tissue engineering is a promising approach for designing modular biomimetic structures that aim to recapitulate the intricate hierarchy and biofunctionality of native human tissues. In recent years, this field has seen exciting progress driven by an increasing knowledge of biological systems and their rational deconstruction into key core components. Relevant advances in the bottom-up assembly of unitary living blocks toward the creation of higher order bioarchitectures based on multicellular-rich structures or multicomponent cell-biomaterial synergies are described. An up-to-date critical overview of long-term existing and rapidly emerging technologies for integrative bottom-up tissue engineering is provided, including discussion of their practical challenges and required advances. It is envisioned that a combination of cell-biomaterial constructs with bioadaptable features and biospecific 3D designs will contribute to the development of more robust and functional humanized tissues for therapies and disease models, as well as tools for fundamental biological studies.

Functional and Biomimetic Materials for Engineering of the Three-Dimensional Cell Microenvironment

The cell microenvironment has emerged as a key determinant of cell behavior and function in development, physiology, and pathophysiology. The extracellular matrix (ECM) within the cell microenvironment serves not only as a structural foundation for cells but also as a source of three-dimensional (3D) biochemical and biophysical cues that trigger and regulate cell behaviors. Increasing evidence suggests that the 3D character of the microenvironment is required for development of many critical cell responses observed in vivo, fueling a surge in the development of functional and biomimetic materials for engineering the 3D cell microenvironment. Progress in the design of such materials has improved control of cell behaviors in 3D and advanced the fields of tissue regeneration, in vitro tissue models, large-scale cell differentiation, immunotherapy, and gene therapy. However, the field is still in its infancy, and discoveries about the nature of cell-microenvironment interactions continue to overturn much early progress in the field. Key challenges continue to be dissecting the roles of chemistry, structure, mechanics, and electrophysiology in the cell microenvironment, and understanding and harnessing the roles of periodicity and drift in these factors. This review encapsulates where recent advances appear to leave the ever-shifting state of the art, and it highlights areas in which substantial potential and uncertainty remain.