FeS2 Nanoparticles Decorated Graphene as Microbial-Fuel-Cell Anode Achieving High Power Density

Fabrication of a Molybdenum Dioxide/Multi-Walled Carbon Nanotubes Nanocomposite as an Anodic Modification Material for High-Performance Microbial Fuel Cells

A nanocomposite of multi-walled carbon nanotubes (MWCNTs) decorated with molybdenum dioxide (MoO2) nanoparticles is fabricated through the reduction of phosphomolybdic acid hydrate on functionalized MWCNTs in a hydrogen-argon (10%) atmosphere in a tube furnace. The MoO2/MWCNTs composite is proposed as an anodic modification material for microbial fuel cells (MFCs). MWCNTs have outstanding physical and chemical peculiarities, with functionalized MWCNTs having substantially large electroactive areas. In addition, combined with the exceptional properties of MoO2 nanoparticles, the synergistic advantages of functionalized MWCNTs and MoO2 nanoparticles give a MoO2/MWCNTs anode a large electroactive area, excellent electronic conductivity, enhanced extracellular electron transfer capacity, and improved nutrient transfer capability. Finally, the power harvesting of an MFC with the MoO2/MWCNTs anode is improved, with the MFC showing long-term repeatability of voltage and current density outputs. This exploratory research advances the fundamental application of anodic modification to MFCs, simultaneously providing valuable guidance for the use of carbon-based transition metal oxide nanomaterials in high-performance MFCs.

Nanomaterials Regulate Bacterial Quorum Sensing: Applications, Mechanisms, and Optimization Strategies

Anti-virulence therapy that interferes with bacterial communication, known as "quorum sensing (QS)", is a promising strategy for circumventing bacterial resistance. Using nanomaterials to regulate bacterial QS in anti-virulence therapy has attracted much attention, which is mainly attributed to unique physicochemical properties and excellent designability of nanomaterials. However, bacterial QS is a dynamic and multistep process, and there are significant differences in the specific regulatory mechanisms and related influencing factors of nanomaterials in different steps of the QS process. An in-depth understanding of the specific regulatory mechanisms and related influencing factors of nanomaterials in each step can significantly optimize QS regulatory activity and enhance the development of novel nanomaterials with better comprehensive performance. Therefore, this review focuses on the mechanisms by which nanomaterials regulate bacterial QS in the signal supply (including signal synthesis, secretion, and accumulation) and signal transduction cascade (including signal perception and response) processes. Moreover, based on the two key influencing factors (i.e., the nanomaterial itself and the environment), optimization strategies to enhance the QS regulatory activity are comprehensively summarized. Collectively, applying nanomaterials to regulate bacterial QS is a promising strategy for anti-virulence therapy. This review provides reference and inspiration for further research on the anti-virulence application of nanomaterials.

Magnetite-boosted syntrophic conversion of acetate to methane during thermophilic anaerobic digestion

Using a batch thermophilic anaerobic system established with 60 mL serum bottles, the mechanism on how microbial enrichments obtained from magnetite-amended paddy soil via repeated batch cultivation affected methane production from acetate was investigated. Magnetite-amended enrichments (MAEs) can improve the methane production rate rather than the methane yield. Compared with magnetite-unamended enrichments, the methane production rate in MAE was improved by 50%, concomitant with the pronounced electrochemical response, high electron transfer capacity, and fast acetate degradation. The promoting effects might be ascribed to direct interspecies electron transfer facilitated by magnetite, where magnetite might function as electron conduits to link the acetate oxidizers (Anaerolineaceae and Peptococcaceae) with methanogens (Methanosarcinaceae). The findings demonstrated the potential application of MAE for boosting methanogenic performance during thermophilic anaerobic digestion.

Rational Design of Hollow Structural Materials for Sodium-Ion Battery Anodes

The development of sodium-ion battery (SIB) anodes is still hindered by their rapid capacity decay and poor rate capabilities. Although there have been some new materials that can be used to fabricate stable anodes, SIBs are still far from wide applications. Strategies like nanostructure construction and material modification have been used to prepare more robust SIB anodes. Among all the design strategies, the hollow structure design is a promising method in the development of advanced anode materials. In the past decade, research efforts have been devoted to modifying the synthetic route, the type of templates, and the interior structure of hollow structures with high capacity and stability. A brief introduction is made to the main material systems and classifications of hollow structural materials first. Then different morphologies of hollow structural materials for SIB anodes from the latest reports are discussed, including nanoboxes, nanospheres, yolk shells, nanotubes, and other more complex shapes. The most used templates for the synthesis of hollow structrual materials are covered and the perspectives are highlighted at the end. This review offers a comprehensive discussion of the synthesis of hollow structural materials for SIB anodes, which could be potentially of use to research areas involving hollow materials design for batteries.

Enhanced bidirectional extracellular electron transfer based on biointerface interaction of conjugated polymers-bacteria biohybrid system

The low bacteria loading capacity and low extracellular electron transfer (EET) efficiency are two major bottlenecks restricting the performance of the bioelectrochemical systems from practical applications. Herein, we demonstrated that conjugated polymers (CPs) could enhance the bidirectional EET efficiency through the intimate biointerface interactions of CPs-bacteria biohybrid system. Upon the formation of CPs/bacteria biohybrid, thick and intact CPs-biofilm formed which ensured close biointerface interactions between bacteria-to-bacteria and bacteria-to-electrode. CPs could promote the transmembrane electron transfer through intercalating into the cell membrane of bacteria. Utilizing the CPs-biofilm biohybrid electrode as anode in microbial fuel cell (MFC), the power generation and lifetime of MFC had greatly improved based on accelerated outward EET. Moreover, using the CPs-biofilm biohybrid electrode as cathode in electrochemical cell, the current density was increased due to the enhanced inward EET. Therefore, the intimate biointerface interaction between CPs and bacteria greatly enhanced the bidirectional EET, indicating that CPs exhibit promising applications in both MFC and microbial electrosynthesis.

Boosting o-xylene removal and power generation in an airlift microbial fuel cell system

Microbial fuel cells (MFCs) are widely acknowledged to be a promising eco-friendly abatement technology of pollutants, and are capable of generating electricity. However, the poor mass transfer and reaction rate in MFCs significantly decrease their treatment capacity for contaminants, especially hydrophobic substances. The present work developed a novel MFC integrated with an airlift (ALR) reactor using a polypyrrole modified anode to promote the bioaccessibility of gaseous o-xylene and attachment of microorganisms. The results indicated that the established ALR-MFC system showed excellent elimination capability, with removal efficiency exceeding 84% even at high o-xylene concentration (1600 mg m^-3). The maximum output voltage of 0.549 V and power density of 13.16 mW m^-2 obtained by the Monod-type model were approximately twice and sixfold higher than that of a conventional MFC, respectively. According to the microbial community analysis, the superior performances of the ALR-MFC in terms of o-xylene removal and power generation were mainly ascribed to the enrichment of degrader (i.e. Shinella) and electrochemical active bacteria (i.e. Proteiniphilum). Moreover, the electricity generation of the ALR-MFC did not decrease at a high O₂ concentration, as O₂ was conducive to o-xylene degradation and electron release. The supplication of an external carbon source such as sodium acetate (NaAc) was conducive to increasing output voltage and coulombic efficiency. The electrochemical analysis revealed that released electrons can be transmitted with the action of NADH dehydrogenase to OmcZ, OmcS, and OmcA outer membrane proteins via a direct or indirect pathway, and ended up transferring to the anode directly.

In Situ Enhanced Yields of Microbial Nanowires: The Key Role of Environmental Stress

The conductive microbial nanowires of Geobacter sulfurreducens serve as a model for long-range extracellular electron transfer (EET), which is considered a revolutionary "green" nanomaterial in the fields of bioelectronics, renewable energy, and bioremediation. However, there is no efficient pathway to induce microorganisms to express a large amount of microbial nanowires. Here, several strategies have been used to successfully induce the expression of microbial nanowires. Microbial nanowire expression was closely related to the concentration of electron acceptors. The microbial nanowire was around 17.02 μm in length, more than 3 times compared to its own length. The graphite electrode was used as an alternative electron acceptor by G. sulfurreducens, which obtained a fast start-up time of 44 h in microbial fuel cells (MFCs). Meanwhile, Fe(III) citrate-coated sugarcane carbon and biochar were prepared to test the applicability of these strategies in the actual microbial community. The unsatisfied EET efficiency between c-type cytochrome and extracellular insoluble electron receptors promoted the expression of microbial nanowires. Hence, microbial nanowires were proposed to be an effective survival strategy for G. sulfurreducens to cope with various environmental stresses. Based on this top-down strategy of artificially constructed microbial environmental stress, this study is of great significance for exploring more efficient methods to induce microbial nanowires expression.

Bimetal-organic framework-derived porous CoFe2O4 nanoparticles as biocompatible anode electrocatalysts for improving the power generation of microbial fuel cells

HYPOTHESIS

The relatively lower power density of Microbial fuel cells (MFCs), primarily resulting from weak biofilm habitation and sluggish extracellular electron transfer (EET) at the anode interface, limits their practical implementation on a large scale. To address this challenge, porous CoFe₂O₄ nanoparticles could be used as anode electrocatalysts based on the following considerations: (i) the introduction of CoFe₂O₄ nanoparticles endows the anode with a rough surface that facilitates biofilm formation; (ii) the positively charged Co and Fe ions improve the interfacial affinity of anodes, enabling rapid immobilization and colonization of negatively bacteria; (iii) the multi-valent metal states of Co and Fe can function as electron shuttles, mediating EET process between biofilm and anode.

EXPERIMENTS

CoFe₂O₄ nanoparticles prepared with a bimetal-organic framework (B-MOF) as precursor, were modified to the surface of carbon cloth as the anode of MFCs.

FINDINGS

MFCs equipped with CoFe₂O₄ anode achieved a maximum power density of 1026.68 mW m^-2, which was approximately 3.4 times higher than that of the pristine carbon cloth. Additionally, the biofilm density and viability on the anode were enhanced after CoFe₂O₄ modification. Considering the facile fabrication process and superior electrocatalytic performance, the CoFe₂O₄ nanoparticles are promising electrocatalysts for high performance and cost-effective MFCs.

Graphene supported FeS2 nanoparticles with sandwich structure as a promising anode for High-Rate Potassium-Ion batteries

Pyrite FeS₂ now emerges as a promising anode for potassium-ion batteries (PIBs) due to its low cost and high theoretical capacity. However, the significant volume expansion, low electrical conductivity, and the ambiguous mechanism related to potassium storage severely hinder its development for PIBs anodes. Herein, FeS₂ nanostructures are skillfully dispersed on the graphene surface layer by layer (FeS₂@C-rGO) to form a sandwich structure by using Fe-based metal organic framework (Fe-MOF) as precursors. The unique structural design can improve the transfer kinetics of K⁺ and effectively buffer the volume expansion during cycling, thereby enhancing the potassium storage performance. As a result, the FeS₂@C-rGO delivers a high capacity of 550 mAh/g at a current density of 0.1 A/g. At a high rate of 2 A/g, the capacity can maintain 171 mAh/g even after 500 cycles. Moreover, the electrochemical reaction mechanism and potassium storage behavior are revealed by in-situ X-ray diffractionand density functional theory calculations. This work not only provides a novel insight into the structural design of electrode materials for high-performance PIBs, but also proposes a valuable understanding of the potassium storage mechanism of the FeS₂-based anode.

Nano magnetite-loaded biochar boosted methanogenesis through shifting microbial community composition and modulating electron transfer

A batch anaerobic fermentation system was employed to clarify how nano magnetite-loaded biochar can improve methanogenic performance of the propionate-degrading consortia (PDC). The nano magnetite-loaded biochar was prepared in a sequential hydrothermal and pyrolysis procedure using the household waste (HW), biogas residue (BR) and Fe (NO₃)₃ as pristine materials. Comprehensive characterization showed that the nano magnetite-loaded biochar ameliorated the biochar properties with large specific surface area, high electrochemical response and low electron transfer resistance. PDC supplemented with the magnetite/BR-originated biochar composites displayed excellent methanogenic performance, where the methane production rate was enhanced by 1.6-fold compared with the control. The nano magnetite-loaded biochar promoted methane production probably by promoting direct interspecies electron transfer between syntrophic bacteria (e.g., Syntrophobacter and Thauera) and their partners (e.g., Methanosaeta). In this process, magnetite might be responsible for triggering rapidly extracellular electron release, whereas both external functional groups and intrinsic graphitic matrices of biochar might work as electron bridges for electron transport.

Three-Dimensional Carbon Monolith Coated by Nano-TiO2 for Anode Enhancement in Microbial Fuel Cells

A three-dimensional (3D) anode is essential for high-performance microbial fuel cells (MFCs). In this study, 3D porous carbon monoliths from a wax gourd (WGCM) were obtained by freeze-drying and carbonization. Nano-TiO2 was further coated onto the surface of WGCM to obtain a nano-TiO2/WGCM anode. The WGCM anode enhanced the maximum power density of MFCs by 167.9% compared with the carbon felt anode, while nano-TiO2/WGCM anode additionally increased the value by 45.8% to achieve 1396.2 mW/m2. WGCM enhancement was due to the 3D porous structure, the good conductivity and the surface hydrophilicity, which enhanced electroactive biofilm formation and anodic electron transfer. In addition, nano-TiO2 modification enhanced the enrichment of Acinetobacter, an electricigen, by 31.0% on the anode to further improve the power production. The results demonstrated that the nano-TiO2/WGCM was an effective anode for power enhancement in MFCs.

Functional Nanomaterial-Modified Anodes in Microbial Fuel Cells: Advances and Perspectives

Microbial fuel cell (MFC) is a promising approach that could utilize microorganisms to oxidize biodegradable pollutants in wastewater and generate electrical power simultaneously. Introducing advanced anode nanomaterials is generally considered as an effective way to enhance MFC performance by increasing bacterial adhesion and facilitating extracellular electron transfer (EET). This review focuses on the key advances of recent anode modification materials, as well as the current understanding of the microbial EET process occurring at the bacteria-electrode interface. Based on the difference in combination mode of the exoelectrogens and nanomaterials, anode surface modification, hybrid biofilm construction and single-bacterial surface modification strategies are elucidated exhaustively. The inherent mechanisms may help to break through the performance output bottleneck of MFCs by rational design of EET-related nanomaterials, and lead to the widespread application of microbial electrochemical systems.

Enhanced transmembrane electron transfer in Shewanella oneidensis MR-1 using gold nanoparticles for high-performance microbial fuel cells

Low efficiency of extracellular electron transfer (EET) is a major bottleneck in developing high-performance microbial fuel cells (MFCs). Herein, we construct Shewanella oneidensis MR-1@Au for the bioanode of MFCs. Through performance recovery experiments of mutants, we proved that abundant Au nanoparticles not only tightly covered the bacteria surface, but were also distributed in the periplasm and cytoplasm, and even embedded in the outer and inner membranes of the cell. These Au nanoparticles could act as electron conduits to enable highly efficient electron transfer between S. oneidensis MR-1 and electrodes. Strikingly, the maximum power density of the S. oneidensis MR-1@Au bioanode reached up to 3749 mW m^-2, which was 17.4 times higher than that with the native bacteria, reaching the highest performance yet reported in MFCs using Au or Au-based nanocomposites as the anode. This work elucidates the role of Au nanoparticles in promoting transmembrane and extracellular electron transfer from the perspective of molecular biology and electrochemistry, while alleviating bottlenecks in MFC performances.

Superior dimethyl disulfide degradation in a microbial fuel cell: Extracellular electron transfer and hybrid metabolism pathways

To enhance the biological degradation of volatile organic sulfur compounds, a microbial fuel cell (MFC) system with superior activity is developed for dimethyl disulfide (DMDS) degradation. The MFC achieves a removal efficiency near 100% within 6 h (initial concentration: 90 mg L^-1) and a maximum biodegradation rate constant of 0.743 mM h^-1. The DMDS removal load attains 2.684 mmol h^-1 L^-1, which is 6.18-2440 times the loads of conventional biodegradation processes reported. Meanwhile, the maximum power density output and corresponding current density output are 5.40 W m^-3 and 40.6 A m^-3, respectively. The main mechanism of extracellular electron transfer is classified as mediated electron transfer, supplemented by direct transfer. Furthermore, the mass balance analysis indicates that methanethiol, S⁰, S^2-, SO₄^2-, HCHO, and CO₂ are the main intermediate and end products involved in the hybrid metabolism pathway of DMDS. Overall, these findings may offer basic information for bioelectrochemical degradation of DMDS and facilitate the application of MFC in waste gas treatment. ENVIRONMENTAL IMPLICATION: Dimethyl disulfide (DMDS), which features poor solubility, odorous smell, and refractory property, is a typical pollutant emitted from the petrochemical industry. For the first time, we develop an MFC system for DMDS degradation. The superior DMDS removal load per unit reactor volume is 6.18-2440 times those of conventional biodegradation processes in literature. Both the electron transfer route and the hybrid metabolism pathway of DMDS are cleared in this work. Overall, these findings give an in-depth understanding of the bioelectrochemical DMDS degradation mechanism and provide an efficient alternative for DMDS removal.

Enrichment of sulfur-oxidizing bacteria using S-doped NiFe2O4 nanosheets as the anode in microbial fuel cell enhances power production and sulfur recovery

Microbial fuel cells (MFCs) have great promise for power generation by oxidizing organic wastewater, yet the challenge to realize high efficiency in simultaneous energy production and resource recovery remains. In this study, we designed a novel MFC anode by synthesizing S-doped NiFe₂O₄ nanosheet arrays on carbon cloth (S10-NiFe₂O₄@CC) to build a three-dimensional (3D) hierarchically porous structure, with the aim to regulate the microbial community of sulfur-cycling microbes in order to enhance power production and elemental sulfur (S⁰) recovery. The S10-NiFe₂O₄@CC anode obtained a faster start-up time of 2 d and the highest power density of 4.5 W/m² in acetate-fed and mixed bacteria-based MFCs. More importantly, sulfide removal efficiency (98.3 %) (initial concentration of 50 mg/L S^2-) could be achieved within 3 d and sulfur (S₈) could be produced. Microbial community analysis revealed that the S10-NiFe₂O₄@CC anode markedly enriched sulfur-oxidizing bacteria (SOB) and promoted enrichment of SOB and sulfate-reducing bacteria (SRB) in the bulk solution as well, leading to the enhancement of power generation and S⁰ recovery. This study shows how carefully designing and optimizing the composition and structure of the anode can lead to the enrichment of a multifunctional microbiota with excellent potential for sulfide removal and resource recovery.

3D Hierarchical Co8FeS8-FeCo2O4/N-CNTs@CF with an Enhanced Microorganisms-Anode Interface for Improving Microbial Fuel Cell Performance

Microbial fuel cells (MFCs) are promising ecofriendly techniques for harvesting bioenergy from organic and inorganic matter. Currently, it is challenging to design MFC anodes with favorable microorganism attachment and fast extracellular electron transfer (EET) rate for high MFC performance. Here we prepared N-doped carbon nanotubes (NCNTs) on carbon felt (CF) and used it as a support for growing hierarchical Co₈FeS₈-FeCo₂O₄/NCNTs core-shell nanostructures (FeCo/NCNTs@CF). We observed improved wettability, specific areal capacitance, and diffusion coefficient, as well as small charge transfer resistance compared with bare CF. MFCs equipped with FeCo/NCNTs@CF displayed a power density of 3.04 W/m² and COD removal amount of 221.0 mg/L/d, about 47.6 and 290.1% improvements compared with that of CF. Biofilm morphology and 16s rRNA gene sequence analysis proved that our anode facilitated the enrichment growth of exoelectrogens. Flavin secretion was also promoted on our hierarchical elelctrode, effectively driving the EET process. This work disclosed that hierarchical nanomaterials modified electrode with tailored physicochemical properties is a promising platform to simultaneously enhance exoelectrogen attachment and EET efficiency for MFCs.

Construction of a new type of three-dimensional honeycomb-structure anode in microbial electrochemical systems for energy harvesting and pollutant removal

Electrode materials occupy most of the construction cost of the microbial electrochemical system (MES), and the low mechanical strength and poor electrochemical performance of the commonly used traditional carbon-based materials restrict the promotion and application of this technology. In this study, polymer-based three-dimensional (3D) honeycomb-structure (HS) materials with good mechanical properties were used as supporting materials. Graphene (GR), carbon nanotube (CNT), and polypyrrole (PPy) was separately chosen as a surface conductivity coating layer for preparing MES anodes. The introduction of GR, CNT, and PPy on HS increased surface roughness, hydrophilicity, O and N content, electrochemically active surface area, and decreased charge transfer internal resistance, which promoted the adhesion of microorganisms on their surface and enhanced the extracellular electron transfer process at the electrode/microbe interface. The CNT-HS anode system got the better maximal power density (1700.7 ± 149.0 mW/m²) of the three modified anode systems and 3.60 times that of MES using CC (471.8 ± 27.2 mW/m²) as the anode. The accelerated reactions of the redox species in the outer cell membrane, the promoted electron shuttle secretion, and the enhanced abundance of the tricarboxylic acid cycle-related functional genes in biofilm led to better performance of the CNT-HS anode system. The CNT-HS anode system also exhibited long-term operational stability (>6 months) and a good chemical oxygen demand degradation effect. Furthermore, CNT-HS material exhibited its cost advantage, and its projected cost is estimated to be about $1.8/m², much lower than the currently used MES anodes ($8.2-548.2/m²). Considering the good mechanical properties, simple preparation process, low manufacturing cost, long-term stability, excellent bio-electrochemical performance, and good pollutant removal ability, HS-based anode has promising potential for high-performance MES in applications.

High-performance free-standing microbial fuel cell anode derived from Chinese date for enhanced electron transfer rates

Traditional anode materials have disadvantages like low specific surface area and poor electrical conductivity. Herein, carbonized Chinese dates (CCD) were synthesized as microbial fuel cells (MFC) anodes. The obtained materials exhibited excellent biocompatibility with fast start-up (within one day) and charge transfer (R_ct 4.0 Ω). Their porous structure allows efficient ion transport and microbial community succession, favorable for long-term operation. The biomass analysis shows that CCD anodes can load higher weight of biomass. High-throughput sequencing (16S rRNA) discovered that CCD anode can enrich Geobacter spp., with highest abundance of 73.4%, much higher than carbon felt (CF, 39.2%). Benefit from these properties, the MFC with CCD anodes possess a maximum power density of 12.17 W m^-3 (1.62 times of commercial carbon felt). In all, the CCD anode exhibits high performance with low cost and easy fabrication, certificating it a promising candidate for an ideal MFC anode material.

S-Doped NiFe2O4 Nanosheets Regulated Microbial Community of Suspension for Constructing High Electroactive Consortia

Iron-based nanomaterials (NMs) are increasingly used to promote extracellular electron transfer (EET) for energy production in bioelectrochemical systems (BESs). However, the composition and roles of planktonic bacteria in the solution regulated by iron-based NMs have rarely been taken into account. Herein, the changes of the microbial community in the solution by S-doped NiFe₂O₄ anodes have been demonstrated and used for constructing electroactive consortia on normal carbon cloth anodes, which could achieve the same level of electricity generation as NMs-mediated biofilm, as indicated by the significantly high voltage response (0.64 V) and power density (3.5 W m⁻²), whereas with different microbial diversity and connections. Network analysis showed that the introduction of iron-based NMs made Geobacter positively interact with f_Rhodocyclaceae, improving the competitiveness of the consortium (Geobacter and f_Rhodocyclaceae). Additionally, planktonic bacteria regulated by S-doped anode alone cannot hinder the stimulation of Geobacter by electricity and acetate, while the assistance of lining biofilm enhanced the cooperation of sulfur-oxidizing bacteria (SOB) and fermentative bacteria (FB), thus promoting the electroactivity of microbial consortia. This study reveals the effect of S-doped NiFe₂O₄ NMs on the network of microbial communities in MFCs and highlights the importance of globality of microbial community, which provides a feasible solution for the safer and more economical environmental applications of NMs.

Promoting biomethane production from propionate with Fe2O3@carbon nanotubes composites

Using a batch anaerobic system constructed with 60 mL serum bottles, potential of a composite material with Fe₂O₃ nanoparticles decorated on carbon nanotubes (CNTs) to enhance biomethane production was investigated. The composites (Fe₂O₃@CNTs) with well dispersed Fe₂O₃ nanoparticles (4.5 nm) were fabricated by a facile thermal decomposition method in a muffle furnace under nitrogen atmosphere. Compared with Fe₂O₃, Fe₂O₃@CNTs showed a large specific surface area and good electrical conductivity. Supplementation of Fe₂O₃@CNTs to the propionate-degrading enrichments enhanced the methane production rate, which was 10.4-fold higher than that in the control experiment without material addition. The addition of Fe₂O₃@CNTs also not only showed a clearly electrochemical response to flavin and cytochrome C, but also reduced the electron transfer resistance when compared to the control. Comparative analysis showed that Fe₂O₃ in Fe₂O₃@CNTs played a key role in initiating electrochemical response and triggering rapid methane production, while CNTs functioned as rapid electron conduits to facilitate electron transfer from iron-reducing bacteria (e.g., Acinetobacter, Syntrophomonas, and Geobacter) to methanogens (e.g. Methanosarcina).

Defined and unknown roles of conductive nanoparticles for the enhancement of microbial current generation: A review

The ability of various bacteria to make use of solid substrates through extracellular electron transfer (EET) or extracellular electron uptake (EEU) has enabled the development of valuable biotechnologies such as microbial fuel cells (MFCs) and microbial electrosynthesis (MES). It is common practice to use metallic and semiconductive nanoparticles (NPs) for microbial current enhancement. However, the effect of NPs is highly variable between systems, and there is no clear guideline for effectively increasing the current generation. In the present review, the proposed mechanisms for enhancing current production in MFCs and MES are summarized, and the critical factors for NPs to enhance microbial current generation are discussed. Implications for microbially induced iron corrosion, where iron sulfide NPs are proposed to enhance the rate of EEU, photochemically driven MES, and several future research directions to further enhance microbial current generation, are also discussed.

Advances in interfacial engineering for enhanced microbial extracellular electron transfer

The extracellular electron transfer (EET) efficiency between electroactive microbes (EAMs) and electrode is a key factor determining the development of microbial electrochemical technology (MET). Currently, the low EET efficiency of EAMs limits the application of MET in the fields of organic matter degradation, electric energy production, seawater desalination, bioremediation and biosensing. Enhancement of the interaction between EAMs and electrode by interfacial engineering methods brings bright prospects for the improvement of the EET efficiency of EAMs. In view of the research in recent years, this mini-review systematically summarizes various interfacial engineering strategies ranging from electrode surface modification to hybrid biofilm formation, then to single cell interfacial engineering and intracellular reformation for promoting the electron transfer between EAMs and electrode, focusing on the applicability and limitations of these methodologies. Finally, the possible key directions, challenges and opportunities for future interfacial engineering to strengthen the microbial EET are proposed in this mini-review.

Heterogeneous Structure Regulated by Selection Pressure on Bacterial Adhesion Optimized the Viability Stratification Structure of Electroactive Biofilms

As the core of microbial fuel cells (MFCs), the components and structure of electroactive biofilms (EABs) are essential for MFC performance. Bacterial adhesion plays a vital role in shaping the structure of EABs, but the effect of bacterial adhesion under selection pressure on EABs has not been systematically studied. Here, the response of the composition, structure, and electrochemical performance of EABs to the selective adhesion pressure due to the selective coordination of Fe(III) and Co(II) with thiol and the different affinities for bacteria on hybrid electrodes (Fe₁Co, Fe₄Co, and Fe₁₀Co) were comprehensively investigated. Compared with carbon cloth (CC), the appropriate selective adhesion pressure of Fe₄Co activated the dead inner core of EABs and optimized their viability stratification structure. Both the total viability and the viability of the inner core layer in the Fe₄Co EAB (0.67, 0.70 ± 0.01) were higher than those of the CC (0.46, 0.54 ± 0.01), Fe₁Co (0.50, 0.48 ± 0.03), and Fe₁₀Co (0.51, 0.51 ± 0.03). Moreover, a higher proportion of proteins was detected in the Fe₄Co EAB, enhancing the redox activity of extracellular polymeric substances. Fe₄Co enriched Geobacter and stimulated microbial metabolism. Electrochemical analysis revealed that the Fe₄Co EAB was the most electroactive EAB, with a maximum power density of 2032.4 mW m^-2, which was 1.7, 1.3, and 1.1 times that of the CC (1202.6 mW m^-2), Fe₁Co (1610.3 mW m^-2), and Fe₁₀Co (1824.4 mW m^-2) EABs, respectively. Our findings confirmed that highly active EABs could be formed by imposing selection pressure on bacterial adhesion.

Activated carbon supported Fe–Cu–NC as an efficient cathode catalyst for a microbial fuel cell

Herein, the output power density produced by Fe–Cu–NC-x as the cathode catalyst of a MFC was higher than that of the AC control.

Core-shell structured polyaniline/polypyrrole composites promoted methane production from anaerobic sludge

The core-shell structured polypyrrole/polyaniline (PPy@PANI) were synthesized by in-situ polymerization method and were used as the conductive medium to enhance methane production from the anaerobic wastewater treatment. It was found that the PPy@PANI has a good performance on methane production from the anaerobic wastewater treatment, and it composites can improve the methane production rate and yield by 70.2% and 28.3% in the initial 4 h compared with the control group. A high methane production rate was achieved when the dosage of PPy@PANI was 0.6 g/L, which suggested that 0.6 g/L was the optimal dosage. Finally, the mechanisms involved in the improved methane production rate by the PPy@PANI were disclosed. The PPy@PANI can enrich the functional microorganisms to enhance both the degradation of organics and the electron transfer, which contributed to the improved methane production rate from the anaerobic wastewater treatment.

Tailoring Surface Properties of Electrodes for Synchronous Enhanced Extracellular Electron Transfer and Enriched Exoelectrogens in Microbial Fuel Cells

An extracellular electron transfer (EET) process between an electroactive biofilm and an electrode is a crucial step for the performance of microbial fuel cells (MFCs), which is highly related to the enrichment of exoelectrogens and the electrocatalytic activity of the electrode. Herein, an efficient N- and Fe-abundant carbon cloth (CC) electrode with the comodification of iron porphyrin (FePor) and polyquaternium-7 (PQ) was synthesized using a facile solvent evaporation and immersion method and developed as an anode (named FePor-PQ) in MFCs. The surface structural characterizations confirmed the successful introduction of N and Fe atoms, whereas FePor-PQ achieved the N content of 9.59 at %, which may offer various active sites for EET. The introduction of PQ contributed to improving the surface hydrophilicity, providing the composite electrode good biocompatibility for bacterial attachment and colonization as well as substrate diffusion. Based on the advantages, the MFC with the FePor-PQ anode produced a maximum power density of 2165.7 mW m^-2, strikingly higher than those of CC (1124.0 mW m^-2), PQ (1668.8 mW m^-2), and FePor (1978.9 mW m^-2). Furthermore, with the EET mediated by the binding of flavins and c-type cytochromes on the outer membrane was enhanced prominently, the typical exoelectrogen Geobacter was enriched up to 55.84% in the FePor-PQ anode biofilm. This work reveals a synergistic effect from heteroatom coating and surface properties tailoring to boost both the EET efficiency and exoelectrogen enrichment for enhancing MFC performance, which also provides valuable insights for designing electrodes in other bio-electrochemical systems.

Silver nanoparticles boost charge-extraction efficiency in Shewanella microbial fuel cells

[Figure: see text].

Modified cobalt-manganese oxide-coated carbon felt anodes: an available method to improve the performance of microbial fuel cells

The novel MnCo₂O₄ (MCO/CF), CNTs-MnCo₂O₄ (CNTs-MCO/CF) and MnFe₂O₄-MnCo₂O₄ (MFO-MCO/CF) electrodes were prepared on carbon felt (CF) by simple hydrothermal and coating method as anodes for MFC. The modified anodes combine the electrocatalytic properties of transition metal oxides (TMOs), the high electrical conductivity of CNTs and the good biocompatibility of CF. These anodes play a synergistically role in the synthesis of structural, to realize high-efficiency electron transfer, low resistance and sufficient space for microbial colonization, while also ensuring high power density. The maximum power density of the composite electrodes CNTs-MCO/CF and MFO-MCO/CF were 4268 mW/m³ and 3660 mW/m³, respectively. The synergistic effect of multi-component effectively improves the performance of MFC. This work not only offers a good design and preparation concept for functional TMOs composite electrodes, but also provides an important guide for the fabrication of CNTs-doped MFC anodes.

FeS2 nanoparticles decorated carbonized Luffa cylindrica as biofilm substrates for fabricating high performance biosensors

A high-performance microbial biosensor was fabricated with a reasonably designed biofilm substrate, where the aerogel of carbonized Luffa cylindrica (LC) was used as the scaffold for loading biofilm and FeS₂ nanoparticles (FeS₂NPs) were employed to modify this aerogel (FeS₂NPs/Gel_LC). The fabricated FeS₂NPs/Gel_LC exhibited a spring-like structure similar with that of the raw LC, which facilitated the linkage of the scaffold and promoted its mechanical strength, and further prolonged the service period of the as-prepared biosensor from few days to two months. Meanwhile, the introduced FeS₂NPs improved the microbial electron transfer of the biofilm and causing an increase in the sensor's signals from 155.0 ± 2.6 to 352.0 ± 17.1 nA and a decrease in the detection limit from 0.95 to 0.38 mg O L^-1 (S/N = 3) for the detection of glucose-glutamic acid (GGA). More important, the FeS₂NPs had been demonstrated to have the capability for modulating a persistent shift of the microbial community with organic pollutant biodegradability. Compared with the Gel_LC, the FeS₂NPs/Gel_LC exhibited a promising performance for measuring the synthetic sewage and real water samples in BOD assay and an increasing inhibition-ratio for detecting 3,5-dichlorophenol (DCP) in toxicity assay. Based on the vast resource and renewability of LC, this work pave a new avenue for developing high-performance microbial biosensors that are expected to be the engineering production.

Carbon-Based Composites as Anodes for Microbial Fuel Cells: Recent Advances and Challenges

Owing to the low price, chemical stability and good conductivity, carbon-based materials have been extensively applied as the anode in microbial fuel cells (MFCs). In this review, apart from the charge storage mechanism and anode requirements, the major work focuses on five categories of carbon-based anode materials (traditional carbon, porous carbon, nano-carbon, metal/carbon composite and polymer/carbon composite). The relationship is demonstrated in depth between the physicochemical properties of the anode surface/interface/bulk (porosity, surface area, hydrophilicity, partical size, charge, roughness, etc.) and the bioelectrochemical performances (electron transfer, electrolyte diffusion, capacitance, toxicity, start-up time, current, power density, voltage, etc.). An outlook for future work is also proposed.

Deciphering Single-Bacterium Adhesion Behavior Modulated by Extracellular Electron Transfer

For bacterial adhesion and biofilm formation, a thorough understanding of the mechanism and effective modulating is lacking due to the complex extracellular electron transfer (EET) at bacteria-surface interfaces. Here, we explore the adhesion behavior of a model electroactive bacteria under various metabolic conditions by an integrated electrochemical single-cell force microscopy system. A nonlinear model between bacterial adhesion force and electric field intensity is established, which provides a theoretical foundation for precise tuning of bacterial adhesion strength by the surface potential and the direction and flux of electron flow. In particular, based on quantitative analyses with equivalent charge distribution modeling and wormlike chain numerical simulations, it is demonstrated that the chain conformation and unfolding events of outer membrane appendages are dominantly impacted by the dynamic bacterial EET processes. This reveals how the anisotropy of bacterial conductive structure can translate into the desired adhesion behavior in different scenarios.

Biosynthetic FeS/BC hybrid particles enhanced the electroactive bacteria enrichment in microbial electrochemical systems

Modifying the surface of an anode can improve electroactive bacteria (EAB) enrichment, thereby enhancing the performance of the associated microbial electrochemical systems (MESs). In this study, biosynthetic FeS nanoparticles were used to modify the anode in MESs. The experimental results demonstrated that the stable maximum voltage of the FeS composited biochar (FeS/BC)-modified anode reached 0.72 V, which is 20% higher than that of the control. The maximum power density with the FeS/BC anode was 793 mW/m², which is 46.31% higher than that obtained with the control (542 mW/m²). According to cyclic voltammetry (CV) analysis, FeS/BC facilitates the direct electron transfer between bacteria and the electrode. The biomass protein concentration of the FeS/BC anode was 841.75 μg/cm², which is almost 1.5 times higher than that of the carbon cloth anode (344.25 μg/cm²); hence, FeS/BC modification can promote biofilm formation. The composition of Geobacter species on the FeS/BC anode (75.16%) was much higher than that on the carbon cloth anode (4.81%). All the results demonstrated that the use of the biosynthetic FeS/BC anode is an environmentally friendly and efficient strategy for enhancing the electroactive biofilm formation and EAB enrichment in MESs.

Customizable design strategies for high-performance bioanodes in bioelectrochemical systems

Bioelectrochemical systems (BESs) can fulfill the demand for renewable energy and wastewater treatment but still face significant challenges to improve their overall performance. Core efforts have been made to enhance the bioelectrode performance, yet, previous approaches are fragmented and have limited applicability, unable to flexibly adjust physicochemical and structural properties of electrodes for specific requirements in various applications. Here, we propose a facile electrode design strategy that integrates three-dimensional printing technology and functionalized modular electrode materials. A customized graphene-based electrode with hierarchical pores and functionalized components (i.e., ferric ions and magnetite nanoparticles) was fabricated. Owing to efficient mass and electron transfer, a high volumetric current density of 10,608 ± 1,036 A/m³ was achieved, the highest volumetric current density with pure Geobacter sulfurreducens to date. This strategy can be readily applied to existing BESs (e.g., microbial fuel cells and microbial electrosynthesis) and provide a feasibility for practical application.

•

A 3D-printed graphene aerogel electrode was proposed for BESs

•

The optimized electrode mass transfer resistance was less than 5% of carbon felt

•

A high volumetric current density of 10,608 ± 1,036 A/m³ was achieved

Nanomaterials Facilitating Microbial Extracellular Electron Transfer at Interfaces

Electrochemically active bacteria can transport their metabolically generated electrons to anodes, or accept electrons from cathodes to synthesize high-value chemicals and fuels, via a process known as extracellular electron transfer (EET). Harnessing of this microbial EET process has led to the development of microbial bio-electrochemical systems (BESs), which can achieve the interconversion of electrical and chemical energy and enable electricity generation, hydrogen production, electrosynthesis, wastewater treatment, desalination, water and soil remediation, and sensing. Here, the focus is on the current understanding of the microbial EET process occurring at both the bacteria-electrode interface and the biotic interface, as well as some attempts to improve the EET by using various nanomaterials. The behavior of nanomaterials in different EET routes and their influence on the performance of BESs are described. The inherent mechanisms will guide rational design of EET-related materials and lead to a better understanding of EET mechanisms.

Enhancement of Mass Transport for Oxygen Reduction Reaction Using Petal-Like Porous Fe-NC Nanosheet

Nitrogen-coordinated single-atom catalysts (SACs) have emerged as a new frontier for accelerating oxygen reduction reaction (ORR) owing to the optimal atom efficiency and fascinating properties. However, augmenting the full exposure of active sites is a crucial challenge in terms of simultaneously pursuing high metal loading of SACs. Here, petal-like porous carbon nanosheets with densely accessible Fe-N₄ moieties (FeNC-D) are constructed by combining the space-confinement of silica and the coordination of diethylenetriaminepentaacetic acid. The resulted FeNC-D catalyst possesses an enhanced mesoporosity and a balanced hydrophobicity/hydrophilicity, which can facilitate mass transport and advance the exposure of inaccessible Fe-N₄ sites, resulting in efficient utilization of active sites. By virtue of the petal-like porous architecture with maximized active site density, FeNC-D demonstrates superior ORR performance in a broad pH range. Remarkably, when utilized as the air cathode in Zn-air battery (ZAB) and microbial fuel cell (MFC), the FeNC-D-based device displays a large power density (356 mW cm^-2 for ZAB and 1041.3 mW m^-2 for MFC) and possesses remarkable stability, substantially outperforming the commercial Pt/C catalyst.

Recent progress of graphene based nanomaterials in bioelectrochemical systems

The application of graphene (Gr) to microbial fuel cells (MFCs) and microbial electrolysis cell (MECs) is considered a very promising approach in terms of enhancing their performance. The superior Gr properties of high electrical and thermal conductivities, along with: superior specific surface area, high electron mobility, and mechanical strength, are the key features that endorse this. Factors impeding the advancement of a microbial fuel cell into commercialization involve primarily the cost of their components, and their production on a small scale. Gr with such outstanding characteristics can help mitigate these challenges, when used as electrode material. The application of Gr as an anode material improves the efficiency of electron transfer and bacterial attachment. When used as a cathode material, it supports the oxygen reduction reaction. This investigation, presents a thorough analysis of the feasibility of Gr as an electrode material in both MFC and MEC applications - based on experimental results from the investigation. Current technological advancements in the implementation of Gr in MFC and MEC are also highlighted in this review. To summarise, the investigation exposes critical issues impeding the advancement of microbial fuel cells, and proposes possible solutions to mitigate these challenges.

Bacteria-affinity aminated carbon nanotubes bridging reduced graphene oxide for highly efficient microbial electrocatalysis

Bioelectrochemical systems (BESs) exhibit great potential for simultaneous wastewater treatment and energy recovery. However, the efficiency of microbial electrocatalysis is fundamentally limited by the high resistance and poor biocompatibility of electrode materials. Herein, we construct a novel "binder-free" 3D biocompatible bioelectrode consists of 1D aminated carbon nanotubes (CNTs-NH₂) and 2D conductive reduced graphene oxide (rGO) nanosheets through one-step electrodeposition. As expected, the maximum current density reached to 3.25 ± 0.03 mA cm^-2 with the rGO@CNTs-NH₂ electrode, which is 4.33-fold higher than that of a bare rGO (0.75 ± 0.01 mA cm^-2), and is among the best performance reported for three-dimensional electrodes. The high microbial electrocatalytic activity is mainly attributed to the excellent performance of electron transfer and bacterial colonization, which originates from the 3D interconnecting scaffold, fast 1D CNTs "e-bridge" and positively charged surface.

Biosynthesized iron sulfide nanoparticles by mixed consortia for enhanced extracellular electron transfer in a microbial fuel cell

The bioanode of mixed consortia was for the first time used to in-situ synthesize iron sulfide nanoparticles in a microbial fuel cell (MFC) over a long-term period (46 days). These poorly crystalline nanoparticles with an average size of 29.97 ± 7.1 nm, comprising of FeS and FeS₂, significantly promoted extracellular electron transfer and thus the electricity generation of the MFC. A maximum power density of 519.00 mW/m² was obtained from the MFC, which was 1.92 times as high as that of the control. The cell viability was promoted by a small amount of iron sulfide nanoparticles but inhibited by the thick nanoparticle "shell" covered on the bacterial cells. Some electroactive and sulfur reducing bacteria (eg. Enterobacteriaceae, Desulfovibrio, and Geobacter) were specifically enriched on the anode. This study provides a novel insight for improving the performance of bioelectrochemical systems through in-situ sustainable nanomaterials biofabrication by mixed consortia.

Internalized Carbon Dots for Enhanced Extracellular Electron Transfer in the Dark and Light

Cellular internalization of nanomaterials to endow cells with more functionalities is highly desirable. Herein, a straightforward strategy for internalizing red-emission carbon dots (CDs) into Shewanella xiamenensis is proposed. This suggests that the internalized CDs not only afford enhanced conductivity of bacteria but also trigger the cellular physiological response to secrete abundant electron shuttles to aid the boosting of extracellular electron transfer (EET) efficiency. Additionally, once illuminated, internalized CDs can also serve as light absorbers to allow for photogenerated electrons to be transferred into cellular metabolism to further facilitate light-enhanced EET processes. Specifically, the findings advance the fundamental understanding of the interaction between internalized carbon-based semiconductor and cells in the dark and light, and provide a facile and effective strategy for enhancing EET efficiency.

A new method for urine electrofiltration and long term power enhancement using surface modified anodes with activated carbon in ceramic microbial fuel cells

This work is presenting for the first time the use of inexpensive and efficient anode material for boosting power production, as well as improving electrofiltration of human urine in tubular microbial fuel cells (MFCs). The MFCs were constructed using unglazed ceramic clay functioning as the membrane and chassis. The study is looking into effective anodic surface modification by applying activated carbon micro-nanostructure onto carbon fibres that allows electrode packing without excessive enlargement of the electrode. The surface treatment of the carbon veil matrix resulted in 3.7 mW (52.9 W m-3 and 1626 mW m-2) of power generated and almost a 10-fold increase in the anodic current due to the doping as well as long-term stability in one year of continuous operation. The higher power output resulted in the synthesis of clear catholyte, thereby i) avoiding cathode fouling and contributing to the active splitting of both pH and ions and ii) transforming urine into a purified catholyte - 30% salt reduction - by electroosmotic drag, whilst generating - rather than consuming - electricity, and in a way demonstrating electrofiltration. For the purpose of future technology implementation , the importance of simultaneous increase in power generation, long-term stability over 1 year and efficient urine cleaning by using low-cost materials, is very promising and helps the technology enter the wider market.

Silver grass-derived activated carbon with coexisting micro-, meso- and macropores as excellent bioanodes for microbial colonization and power generation in sustainable microbial fuel cells

In this study, highly biocompatible three-dimensional hierarchically porous activated carbon from the low-cost silver grass (Miscanthus sacchariflorus) has been fabricated through a facile carbonization approach and tested it as bioanode in microbial fuel cell (MFC) using Escherichia coli as biocatalyst. This silver grass-derived activated carbon (SGAC) exhibited an unprecedented specific surface area of 3027 m² g^-1 with the coexistence of several micro-, meso-, and macropores. The synergistic effect from pore structure (macropores - hosting E. coli to form biofilm and facilitates internal mass transfer; mesopores - favors fast electron transfer; and micropores - promotes nutrient transport to the biofilm) with very high surface area facilitates excellent extracellular electron transfer (EET) between the anode and biofilm which resulted in higher power output of 963 mW cm^-2. Based on superior biocompatibility, low cost, environment-friendliness, and facile fabrication, the proposed SGAC bioanode could have a great potential for high-performance and cost-effective sustainable MFCs.

Improved cathodic oxygen reduction and bioelectricity generation of electrochemical reactor based on reduced graphene oxide decorated with titanium-based composites

A kind of reduced graphene oxide decorated with titanium-based (RGO/TiO₂) composites are successfully synthesized and employed in this current study as a novel nonprecious metal catalyst for enhancing bioelectricity generation and cathodic oxygen reduction reaction (ORR) in single chamber microbial fuel cells (MFCs). Compared with commercial Pt/C, RGO/TiO₂ shows obviously enhanced oxygen reduction reaction activity due to the appropriately-permeated, large electrochemical active area, enough exposure of electrocatalytic active sites of RGO/TiO₂. The air-cathode MFC with RGO/TiO₂-1 cathode achieves 1786.7 mW m^-3 of power density, 86.7% ± 1.2% of COD removal and 31.6% ± 1.1% of CE, which are higher than commercial Pt/C. Moreover, RGO/TiO₂-1 cathode exhibits high-effective electrocatalytic activity, and the power density of RGO/TiO₂-1 can keep a stable level and only has a minor decline (5.35%) during 30-cycles operation. These results indicate that RGO/TiO₂-1 is a potential cathode catalyst, markedly enhancing cathode ORR, wastewater treatment efficiency, and bioelectricity generation of MFC.