Manipulating the Mixed-Perovskite Crystallization Pathway Unveiled by In Situ GIWAXS

High-efficiency and thermally stable FACsPbI3 perovskite photovoltaics

α-FA1-xCsxPbI3 is a promising absorbent material for efficient and stable perovskite solar cells (PSCs)1,2. However, the most efficient α-FA1-xCsxPbI3 PSCs require the inclusion of the additive methylammonium chloride3,4, which generates volatile organic residues (methylammonium) that limit device stability at elevated temperatures5. Previously, the highest certified power-conversion efficiency of α-FA1-xCsxPbI3 PSCs without methylammonium chloride was only approximately 24% (refs. 6,7), and these PSCs have yet to exhibit any stability advantages. Here we identify interfacial contact loss caused by the accumulation of Cs+ in conventional α-FA1-xCsxPbI3 PSCs, which deteriorates device performance and stability. Through in situ grazing-incidence wide-angle X-ray scattering analysis and density functional theory calculations, we demonstrate an intermediate-phase-assisted crystallization pathway enabled by acetate surface coordination to fabricate high-quality α-FA1-xCsxPbI3 films, without using the methylammonium additive. We herein report a certified stabilized power output efficiency of 25.94% and a reverse-scanning power-conversion efficiency of 26.64% for α-FA1-xCsxPbI3 PSCs. Moreover, the devices exhibited negligible contact losses and enhanced operational stability. They retained over 95% of their initial power-conversion efficiency after operating for over 2,000 h at the maximum power point under 1 sun, 85 °C and 60% relative humidity (ISOS-L-3).

Stabilization of Perovskite Solar Cells by a Universal Dilution Strategy: The Crystallization Control of Blade-Coating

Solvent engineering is one of the most effective strategies to control perovskite film quality, which directly affects the performance of perovskite solar cells (PSCs). Here, we introduce volatile acetonitrile (ACN) into the traditional solvent system (i.e., N,N-dimethylformamide and N-methyl-2-pyrrolidone) to dilute the perovskite precursors from 1.43 M to lower concentration (0.6-0.8 M). The dilution strategy can effectively improve the stability of the precursor solution and maintain similar film quality and device performance as those with high solution concentration (1.43 M). Notably, the devices with low-concentration precursors (0.6-0.8 M) show efficiency of 20.85% and improved long-term (>1000 h) storage stability compared to the device with high precursor concentration by blade-coating. Meanwhile, the material cost can be reduced by more than 50% when diluting to 0.6-0.8 M. These results demonstrate a universal dilution method which can provide guidance for the research and development of low-cost and high stability PSCs.

Synchrotron Radiation-Based In Situ GIWAXS for Metal Halide Perovskite Solution Spin-Coating Fabrication

Solution-processable perovskite-based devices are potentially very interesting because of their relatively cheap fabrication cost but outstanding optoelectronic performance. However, the solution spin-coating process involves complicated processes, including perovskite solution droplets, nucleation of perovskite, and formation of intermediate perovskite films, resulting in complicated crystallization pathways for perovskite films under annealing. Understanding and therefore controlling the fabrication process of perovskites is difficult. Recently, synchrotron radiation-based in situ grazing-incidence wide-angle X-ray scattering (GIWAXS) techniques, which possess the advantages of high collimation, high resolution, and high brightness, have enabled to bridge complicated perovskite structure information with device performance by revealing the real-time crystallization pathways of perovskites during the spin-coating process. Herein, the developments of synchrotron radiation-based in situ GIWAXS are discussed in the study of the crystallization process of perovskites, especially revealing the important crystallization mechanisms of state-of-the-art perovskite optoelectronic devices with high performance. At the end, several potential applications and challenges associated with in situ GIWAXS techniques for perovskite-based devices are highlighted.

Lead-Chelating Intermediate for Air-Processed Phase-Pure FAPbI3 Perovskite Solar Cells

Formamidinium-lead triiodide (FAPbI3) perovskite holds promise as a prime candidate in the realm of perovskite photovoltaics. However, the photo-active α-FAPbI3 phase, existing as a metastable state, is observable solely at elevated temperatures and is susceptible to degradation into the δ-phase in ambient air. Therefore, the attainment of phase-stable α-FAPbI3 in ambient conditions has become a crucial objective in perovskite research. Here, we proposed an efficient conversion process of PbI2 into the α-FAPbI3 perovskites in ambient air. This conversion was facilitated by the introduction of chelating molecules, which interacted with PbI2 to form an intermediate phase. Due to the reduced formation barrier resulting from the altered reaction pathway, this stable intermediate phase transitioned directly into α-FAPbI3 upon the deposition of the organic cation solution, effectively bypassing the formation of δ-FAPbI3. Consequently, the ambient-fabricated FAPbI3 perovskite solar cells (PSCs) exhibited an outstanding power conversion efficiency of 25.08 %, along with a high open-circuit voltage of 1.19 V. Furthermore, the unencapsulated devices demonstrated remarkable environmental stability. Notably, this innovative approach promises broad applicability across various chelating molecules, opening new avenues for further progress in the ambient air fabrication of FAPbI3 PSCs.

Nuclei engineering for even halide distribution in stable perovskite/silicon tandem solar cells

Wide-bandgap (WBG) absorbers in tandem configurations suffer from poor crystallinity and weak texture, which leads to severe mixed halide-cation ion migration and phase segregation during practical operation. We control WBG film growth insensitive to compositions by nucleating the 3C phase before any formation of bromine-rich aggregates and 2H phases. The resultant WBG absorbers show improved crystallinity and strong texture with suppressed nonradiative recombination and enhanced resistance to various aging stresses. Perovskite/silicon tandem solar cells achieve power conversion efficiencies of 29.4% (28.8% assessed by a third party) in a 25-square centimeter active area and 32.5% in a 1-square centimeter active area. These solar cells retained 98.3 and 90% of the original efficiency after 1301 and 800 hours of operation at 25° and 50°C, respectively, at the maximum power point (AM 1.5G illumination, full spectrum, 1-sun) when encapsulated.

Interface Dipole Management of D-A-Type Molecules for Efficient Perovskite Solar Cells

Interfacial engineering of perovskite films has been the main strategies in improving the efficiency and stability of perovskite solar cells (PSCs). In this study, three new donor-acceptor (D-A)-type interfacial dipole (DAID) molecules with hole-transporting and different anchoring units are designed and employed in PSCs. The formation of interface dipoles by the DAID molecules on the perovskite film can efficiently modulate the energy level alignment, improve charge extraction, and reduce non-radiative recombination. Among the three DAID molecules, TPA-BAM with amide group exhibits the best chemical and optoelectrical properties, achieving a champion PCE of 25.29 % with the enhanced open-circuit voltage of 1.174 V and fill factor of 84.34 %, due to the reduced defect density and improved interfacial hole extraction. Meanwhile, the operational stability of the unencapsulated device has been significantly improved. Our study provides a prospect for rationalized screening of interfacial dipole materials for efficient and stable PSCs.

Acceleration of radiative recombination for efficient perovskite LEDs

The increasing demands for more efficient and brighter thin-film light-emitting diodes (LEDs) in flat-panel display and solid-state lighting applications have promoted research into three-dimensional (3D) perovskites. These materials exhibit high charge mobilities and low quantum efficiency droop1-6, making them promising candidates for achieving efficient LEDs with enhanced brightness. To improve the efficiency of LEDs, it is crucial to minimize nonradiative recombination while promoting radiative recombination. Various passivation strategies have been used to reduce defect densities in 3D perovskite films, approaching levels close to those of single crystals3. However, the slow radiative (bimolecular) recombination has limited the photoluminescence quantum efficiencies (PLQEs) of 3D perovskites to less than 80% (refs. 1,3), resulting in external quantum efficiencies (EQEs) of LED devices of less than 25%. Here we present a dual-additive crystallization method that enables the formation of highly efficient 3D perovskites, achieving an exceptional PLQE of 96%. This approach promotes the formation of tetragonal FAPbI3 perovskite, known for its high exciton binding energy, which effectively accelerates the radiative recombination. As a result, we achieve perovskite LEDs with a record peak EQE of 32.0%, with the efficiency remaining greater than 30.0% even at a high current density of 100 mA cm-2. These findings provide valuable insights for advancing the development of high-efficiency and high-brightness perovskite LEDs.

An Integrated Deposition and Passivation Strategy for Controlled Crystallization of 2D/3D Halide Perovskite Films

This work introduces a simplified deposition procedure for multidimensional (2D/3D) perovskite thin films, integrating a phenethylammonium chloride (PEACl)-treatment into the antisolvent step when forming the 3D perovskite. This simultaneous deposition and passivation strategy reduces the number of synthesis steps while simultaneously stabilizing the halide perovskite film and improving the photovoltaic performance of resulting solar cell devices to 20.8%. Using a combination of multimodal in situ and additional ex situ characterizations, it is demonstrated that the introduction of PEACl during the perovskite film formation slows down the crystal growth process, which leads to a larger average grain size and narrower grain size distribution, thus reducing carrier recombination at grain boundaries and improving the device's performance and stability. The data suggests that during annealing of the wet film, the PEACl diffuses to the surface of the film, forming hydrophobic (quasi-)2D structures that protect the bulk of the perovskite film from humidity-induced degradation.

Modular slot-die coater for in situ grazing-incidence x-ray scattering experiments on thin films

Multimodal in situ experiments during slot-die coating of thin films pioneer the way to kinetic studies on thin-film formation. They establish a powerful tool to understand and optimize the formation and properties of thin-film devices, e.g., solar cells, sensors, or LED films. Thin-film research benefits from time-resolved grazing-incidence wide- and small-angle x-ray scattering (GIWAXS/GISAXS) with a sub-second resolution to reveal the evolution of crystal structure, texture, and morphology during the deposition process. Simultaneously investigating optical properties by in situ photoluminescence measurements complements in-depth kinetic studies focusing on a comprehensive understanding of the triangular interdependency of processing, structure, and function for a roll-to-roll compatible, scalable thin-film deposition process. Here, we introduce a modular slot-die coater specially designed for in situ GIWAXS/GISAXS measurements and applicable to various ink systems. With a design for quick assembly, the slot-die coater permits the reproducible and comparable fabrication of thin films in the lab and at the synchrotron using the very same hardware components, as demonstrated in this work by experiments performed at Deutsches Elektronen-Synchrotron (DESY). Simultaneous to GIWAXS/GISAXS, photoluminescence measurements probe optoelectronic properties in situ during thin-film formation. An environmental chamber allows to control the atmosphere inside the coater. Modular construction and lightweight design make the coater mobile, easy to transport, quickly extendable, and adaptable to new beamline environments.

Modeling and Fundamental Dynamics of Vacuum, Gas, and Antisolvent Quenching for Scalable Perovskite Processes

Hybrid perovskite photovoltaics (PVs) promise cost-effective fabrication with large-scale solution-based manufacturing processes as well as high power conversion efficiencies. Almost all of today's high-performance solution-processed perovskite absorber films rely on so-called quenching techniques that rapidly increase supersaturation to induce a prompt crystallization. However, to date, there are no metrics for comparing results obtained with different quenching methods. In response, the first quantitative modeling framework for gas quenching, anti-solvent quenching, and vacuum quenching is developed herein. Based on dynamic thickness measurements in a vacuum chamber, previous works on drying dynamics, and commonly known material properties, a detailed analysis of mass transfer dynamics is performed for each quenching technique. The derived models are delivered along with an open-source software framework that is modular and extensible. Thereby, a deep understanding of the impact of each process parameter on mass transfer dynamics is provided. Moreover, the supersaturation rate at critical concentration is proposed as a decisive benchmark of quenching effectiveness, yielding ≈ 10-3 - 10-1s-1 for vacuum quenching, ≈ 10-5 - 10-3s-1 for static gas quenching, ≈ 10-2 - 100s-1 for dynamic gas quenching and ≈ 102s-1 for antisolvent quenching. This benchmark fosters transferability and scalability of hybrid perovskite fabrication, transforming the "art of device making" to well-defined process engineering.

Toward stabilization of formamidinium lead iodide perovskites by defect control and composition engineering

Phase instability poses a serious challenge to the commercialization of formamidinium lead iodide (FAPbI3)-based solar cells and optoelectronic devices. Here, we combine density functional theory and machine learning molecular dynamics simulations, to investigate the mechanism driving the undesired α-δ phase transition of FAPbI3. Prevalent iodine vacancies and interstitials can significantly expedite the structural transition kinetics by inducing robust covalency during transition states. Extrinsically, the detrimental roles of atmospheric moisture and oxygen in degrading the FAPbI3 perovskite phase are also rationalized. Significantly, we discover the compositional design principles by categorizing that A-site engineering primarily governs thermodynamics, whereas B-site doping can effectively manipulate the kinetics of the phase transition in FAPbI3, highlighting lanthanide ions as promising B-site substitutes. A-B mixed doping emerges as an efficient strategy to synergistically stabilize α-FAPbI3, as experimentally demonstrated by substantially higher initial optoelectronic characteristics and significantly enhanced phase stability in Cs-Eu doped FAPbI3 as compared to its Cs-doped counterpart. This study provides scientific guidance for the design and optimization of long-term stable FAPbI3-based solar cells and other optoelectronic devices through defect control and synergetic composition engineering.

Aqueous synthesis of perovskite precursors for highly efficient perovskite solar cells

High-purity precursor materials are vital for high-efficiency perovskite solar cells (PSCs) to reduce defect density caused by impurities in perovskite. In this study, we present aqueous synthesized perovskite microcrystals as precursor materials for PSCs. Our approach enables kilogram-scale mass production and synthesizes formamidinium lead iodide (FAPbI3) microcrystals with up to 99.996% purity, with an average value of 99.994 ± 0.0015%, from inexpensive, low-purity raw materials. The reduction in calcium ions, which made up the largest impurity in the aqueous solution, led to the greatest reduction in carrier trap states, and its deliberate introduction was shown to decrease device performance. With these purified precursors, we achieved a power conversion efficiency (PCE) of 25.6% (25.3% certified) in inverted PSCs and retained 94% of the initial PCE after 1000 hours of continuous simulated solar illumination at 50°C.

High-Quality Hybrid Perovskite Thin Films by Post-Treatment Technologies in Photovoltaic Applications

Incredible progress in photovoltaic devices based on hybrid perovskite materials has been made in the past few decades, and a record-certified power conversion efficiency (PCE) of over 26% has been achieved in single-junction perovskite solar cells (PSCs). In the fabrication of high-efficiency PSCs, the postprocessing procedures toward perovskites are essential for designing high-quality perovskite thin films; developing efficient and reliable post-treatment techniques is very important to promote the progress of PSCs. Here, recent post-treatment technological reforms toward perovskite thin films are summarized, and the principal functions of the post-treatment strategies on the design of high-quality perovskite films have been thoroughly analyzed by dividing into two categories in this review: thermal annealing (TA)-related technique and TA-free technique. The latest research progress of the above two types of post-treatment techniques is summarized and discussed, focusing on the optimization of postprocessing conditions, the regulation of perovskite qualities, and the enhancement of device performance. Finally, an outlook of the prospect trends and future challenges for the fabrication of the perovskite layer and the production of highly efficient PSCs is given.

Trace Water in Lead Iodide Affecting Perovskite Crystal Nucleation Limits the Performance of Perovskite Solar Cells

The experimental replicability of highly efficient perovskite solar cells (PSCs) is a persistent challenge faced by laboratories worldwide. Although trace impurities in raw materials can impact the experimental reproducibility of high-performance PSCs, the in situ study of how trace impurities affect perovskite film growth is never investigated. Here, light is shed on the impact of inevitable water contamination in lead iodide (PbI2 ) on the replicability of device performance, mainly depending on the synthesis methods of PbI2 . Through synchrotron-based structure characterization, it is uncovered that even slight additions of water to PbI2 accelerate the crystallization process in the perovskite layer during annealing. However, this accelerated crystallization also results in an imbalance of charge-carrier mobilities, leading to a degradation in device performance and reduced longevity of the solar cells. It is also found that anhydrous PbI2 promotes a homogenous nucleation process and improves perovskite film growth. Finally, the PSCs achieve a remarkable certified power conversion efficiency of 24.3%. This breakthrough demonstrates the significance of understanding and precisely managing the water content in PbI2 to ensure the experimental replicability of high-efficiency PSCs.

Thiol-Functionalized Conjugated Metal-Organic Frameworks for Stable and Efficient Perovskite Photovoltaics

Metal-organic frameworks (MOFs) have been investigated recently in perovskite photovoltaics owing to their potential to boost optoelectronic performance and device stability. However, the impact of variations in the MOF side chain on perovskite characteristics and the mechanism of MOF/perovskite film formation remains unclear. In this study, three nanoscale thiol-functionalized UiO-66-type Zr-based MOFs (UiO-66-(SH)2 , UiO-66-MSA, and UiO-66-DMSA) are systematically employed and examined in perovskite solar cells (PSCs). Among these MOFs, UiO-66-(SH)2 , with its rigid organic ligands, exhibited a strong interaction with perovskite materials with more efficient suppression of perovskite vacancy defects. More importantly, A detailed and in-depth discussion is provided on the formation mechanism of UiO-66-(SH)2 -assisted perovskite film upon in situ GIWAXS performed during the annealing process. The incorporation of UiO-66-(SH)2 additives substantially facilitates the conversion of PbI2 into the perovskite phase, prolongs the duration of stage I, and induces a delayed phase transformation pathway. Consequently, the UiO-66-(SH)2 -assisted device demonstrates reduced defect density and superior optoelectronic properties with optimized power conversion efficiency of 24.09% and enhanced long-term stability under ambient environment and continuous light illumination conditions. This study acts as a helpful design guide for desired MOF/perovskite structures, enabling further advancements in MOF/perovskite optoelectronic devices.

Crystallization Control for Ambient Printed FA-Based Lead Triiodide Perovskite Solar Cells

Upscalable printing of high-performance and stable perovskite solar cells (PSCs) is highly desired for commercialization. However, the efficiencies of printed PSCs lag behind those of their lab-scale spin-coated counterparts owing to the lack of systematic understanding and control over perovskite crystallization dynamics. Here, the controlled crystallization dynamics achieved using an additive 1-butylpyridine tetrafluoroborate (BPyBF4 ) for high-quality ambient printed α-formamidinium lead triiodide (FAPbI3 ) perovskite films are reported. Using in situ grazing-incidence wide-angle X-ray scattering and optical diagnostics, the spontaneous formation of α-FAPbI3 from precursors during printing without the involvement of  δ-FAPbI3 is demonstrated. The addition of BPyBF4 delays the crystallization onset of α-FAPbI3 , enhances the conversion from sol-gel to perovskite, and reduces stacking defects during printing. Therefore, the altered crystallization results in fewer voids, larger grains, and less trap-induced recombination loss within printed films. The printed PSCs yield high power conversion efficiencies of 23.50% and 21.60% for a 0.09 cm-2 area device and a 5 cm × 5 cm-area module, respectively. Improved device stability is further demonstrated, i.e., approximately 94% of the initial efficiency is retained for over 2400 h under ambient conditions without encapsulation. This study provides an effective crystallization control method for the ambient printing manufacture of large-area high-performance PSCs.

In situ imaging of the atomic phase transition dynamics in metal halide perovskites

Phase transition dynamics are an important concern in the wide applications of metal halide perovskites, which fundamentally determine the optoelectronic properties and stabilities of perovskite materials and devices. However, a more in-depth understanding of such a phase transition process with real atomic resolution is still limited by the immature low-dose electron microscopy and in situ imaging studies to date. Here, we apply an emergent low-dose imaging technique to identify different phase structures (α, β and γ) in CsPbI3 nanocrystals during an in-situ heating process. The rotation angles of PbI6 octahedrons can be measured in these images to quantitatively describe the thermal-induced phase distribution and phase transition. Then, the dynamics of such a phase transition are studied at a macro time scale by continuously imaging the phase distribution in a single nanocrystal. The structural evolution process of CsPbI3 nanocrystals at the particle level, including the changes in morphology and composition, is also visualized with increasing temperature. These results provide atomic insights into the transition dynamics of perovskite phases, indicating a long-time transition process with obvious intermediate states and spatial distribution that should be generally considered in the further study of structure-property relations and device performance.

In situ spin coater for multimodal grazing incidence x-ray scattering studies

We present herein a custom-made, in situ, multimodal spin coater system with an integrated heating stage that can be programmed with spinning and heating recipes and that is coupled with synchrotron-based, grazing-incidence wide- and small-angle x-ray scattering. The spin coating system features an adaptable experimental chamber, with the ability to house multiple ancillary probes such as photoluminescence and visible optical cameras, to allow for true multimodal characterization and correlated data analysis. This system enables monitoring of structural evolutions such as perovskite crystallization and polymer self-assembly across a broad length scale (2 Å-150 nm) with millisecond temporal resolution throughout a complete thin film fabrication process. The use of this spin coating system allows scientists to gain a deeper understanding of temporal processes of a material system, to develop ideal conditions for thin film manufacturing.

In Situ and Operando Characterization Techniques in Stability Study of Perovskite-Based Devices

Metal halide perovskite materials have demonstrated significant potential in various optoelectronic applications, such as photovoltaics, light emitting diodes, photodetectors, and lasers. However, the stability issues of perovskite materials continue to impede their widespread use. Many studies have attempted to understand the complex degradation mechanism and dynamics of these materials. Among them, in situ and/or operando approaches have provided remarkable insights into the degradation process by enabling precise control of degradation parameters and real-time monitoring. In this review, we focus on these studies utilizing in situ and operando approaches and demonstrate how these techniques have contributed to reveal degradation details, including structural, compositional, morphological, and other changes. We explore why these two approaches are necessary in the study of perovskite degradation and how they can be achieved by upgrading the corresponding ex situ techniques. With recent stability improvements of halide perovskite using various methods (compositional engineering, surface engineering, and structural engineering), the degradation of halide perovskite materials is greatly retarded. However, these improvements may turn into new challenges during the investigation into the retarded degradation process. Therefore, we also highlight the importance of enhancing the sensitivity and probing range of current in situ and operando approaches to address this issue. Finally, we identify the challenges and future directions of in situ and operando approaches in the stability research of halide perovskites. We believe that the advancement of in situ and operando techniques will be crucial in supporting the journey toward enhanced perovskite stability.

Monolithically-grained perovskite solar cell with Mortise-Tenon structure for charge extraction balance

Although the power conversion efficiency values of perovskite solar cells continue to be refreshed, it is still far from the theoretical Shockley-Queisser limit. Two major issues need to be addressed, including disorder crystallization of perovskite and unbalanced interface charge extraction, which limit further improvements in device efficiency. Herein, we develop a thermally polymerized additive as the polymer template in the perovskite film, which can form monolithic perovskite grain and a unique "Mortise-Tenon" structure after spin-coating hole-transport layer. Importantly, the suppressed non-radiative recombination and balanced interface charge extraction benefit from high-quality perovskite crystals and Mortise-Tenon structure, resulting in enhanced open-circuit voltage and fill-factor of the device. The PSCs achieve certified efficiency of 24.55% and maintain >95% initial efficiency over 1100 h in accordance with the ISOS-L-2 protocol, as well as excellent endurance according to the ISOS-D-3 accelerated aging test.

Compact sample environment for in situ X-ray scattering during spin-coating

We demonstrate a compact sample environment for the in situ study of crystallization kinetics of thin films on synchrotron beamlines, featuring atmospheric control, automated deposition, spin-coating, and annealing stages. The setup is suitable for studying thin film growth in real time using grazing-incidence X-ray diffraction techniques. Humidity and oxygen levels are being detected by sensors. The spinning stage exhibits low vertical oscillation amplitude (∼3μm at speeds up to 10 000 rpm) and can optionally be employed for antisolvent application or gas quenching to investigate the impact of these techniques, which are often used to assist thin film growth. Differential reflectance spectroscopy is implemented in the spin-coater environment for inspecting thin film thickness and optical properties. The infrared radiation-based annealing system consists of a halogen lamp and a holder with an adjustable lamp-to-sample distance, while the sample surface temperature is monitored by a pyrometer. All features of the sample environment can be controlled remotely by the control software at synchrotron beamlines. In order to test and demonstrate the performance, the crystallization pathway of the antisolvent-assisted MAPbI3 (MA = methylammonium) perovskite thin film during the spinning and annealing stages is monitored and discussed.

Residual Strain Evolution Induced by Crystallization Kinetics During Anti-Solvent Spin Coating in Organic-Inorganic Hybrid Perovskite

Organic-inorganic hybrid perovskite (OIHP) polycrystalline thin films are attractive due to their outstanding photoelectronic properties. The anti-solvent spin coating method is the most widely used to synthesize these thin films, and the residual strain is inevitably originates and evolves during the process. However, this residual strain evolution induced by crystallization kinetics is still poorly understood. In this work, the in situ and ex situ synchrotron grazing-incidence wide-angle X-ray scattering (GIWAXS) are utilized to characterize the evolution and distribution of the residual strain in the OIHP polycrystalline thin film during the anti-solvent spin coating process. A mechanical model is established and the mechanism of the crystallization kinetics-induced residual strain evolution process is discussed. This work reveals a comprehensive understanding of the residual strain evolution during the anti-solvent spin coating process in the OIHP polycrystalline thin films and provides important guidelines for the residual strain-related strain engineering, morphology control, and performance enhancement.

Elucidating Structure Formation in Highly Oriented Triple Cation Perovskite Films

Metal halide perovskites are an emerging class of crystalline semiconductors of great interest for application in optoelectronics. Their properties are dictated not only by their composition, but also by their crystalline structure and microstructure. While significant efforts are dedicated to the development of strategies for microstructural control, significantly less is known about the processes that govern the formation of their crystalline structure in thin films, in particular in the context of crystalline orientation. This work investigates the formation of highly oriented triple cation perovskite films fabricated by utilizing a range of alcohols as an antisolvent. Examining the film formation by in situ grazing-incidence wide-angle X-ray scattering reveals the presence of a short-lived highly oriented crystalline intermediate, which is identified as FAI-PbI₂ -xDMSO. The intermediate phase templates the crystallization of the perovskite layer, resulting in highly oriented perovskite layers. The formation of this dimethylsulfoxide (DMSO) containing intermediate is triggered by the selective removal of N,N-dimethylformamide (DMF) when alcohols are used as an antisolvent, consequently leading to differing degrees of orientation depending on the antisolvent properties. Finally, this work demonstrates that photovoltaic devices fabricated from the highly oriented films, are superior to those with a random polycrystalline structure in terms of both performance and stability.

Co-Solvent Engineering Contributing to Achieve High-Performance Perovskite Solar Cells and Modules Based on Anti-Solvent Free Technology

The pinhole-free and defect-less perovskite film is crucial for achieving high efficiency and stable perovskite solar cells (PSCs), which can be prepared by widely used anti-solvent crystallization strategies. However, the involvement of anti-solvent requires precise control and inevitably brings toxicity in fabrication procedures, which limits its large-scale industrial application. In this work, a facile and effective co-solvent engineering strategy is introduced to obtain high- quality perovskite film while avoiding the usage of anti-solvent. The uniform and compact perovskite polycrystalline films have been fabricated through the addition of co-solvent that owns strong coordination capacity with perovskite components , meanwhile possessing the weaker interaction with main solvent . With those strategies, a champion power conversion efficiency (PCE) of 22% has been achieved with the optimal co-solvent, N-methylpyrrolidone (NMP) and without usage of anti-solvent. Subsequently, PSCs based on NMP show high repeatability and good shelf stability (80% PCE remains after storing in ambient condition for 30 days). Finally, the perovskite solar module (5 × 5 cm) with 7 subcells connects in series yielding champion PCE of 16.54%. This strategy provides a general guidance of co-solvent selection for PSCs based on anti-solvent free technology and promotes commercial application of PSCs.

In Situ and Operando Characterizations of Metal Halide Perovskite and Solar Cells: Insights from Lab-Sized Devices to Upscaling Processes

The performance and stability of metal halide perovskite solar cells strongly depend on precursor materials and deposition methods adopted during the perovskite layer preparation. There are often a number of different formation pathways available when preparing perovskite films. Since the precise pathway and intermediary mechanisms affect the resulting properties of the cells, in situ studies have been conducted to unravel the mechanisms involved in the formation and evolution of perovskite phases. These studies contributed to the development of procedures to improve the structural, morphological, and optoelectronic properties of the films and to move beyond spin-coating, with the use of scalable techniques. To explore the performance and degradation of devices, operando studies have been conducted on solar cells subjected to normal operating conditions, or stressed with humidity, high temperatures, and light radiation. This review presents an update of studies conducted in situ using a wide range of structural, imaging, and spectroscopic techniques, involving the formation/degradation of halide perovskites. Operando studies are also addressed, emphasizing the latest degradation results for perovskite solar cells. These works demonstrate the importance of in situ and operando studies to achieve the level of stability required for scale-up and consequent commercial deployment of these cells.

Critical Influence of Organic A'-Site Ligand Structure on 2D Perovskite Crystallization

Organic A'-site ligand structure plays a crucial role in the crystal growth of 2D perovskites, but the underlying mechanism has not been adequately understood. This problem is tackled by studying the influence of two isomeric A'-site ligands, linear-shaped n-butylammonium (n-BA⁺ ) and branched iso-butylammonium (iso-BA⁺ ), on 2D perovskites from precursor to device, with a combination of in situ grazing-incidence wide-angle X-ray scattering and density functional theory. It is found that branched iso-BA⁺ , due to the lower aggregation enthalpies, tends to form large-size clusters in the precursor solution, which can act as pre-nucleation sites to expedite the crystallization of vertically oriented 2D perovskites. Furthermore, iso-BA⁺ is less likely to be incorporated into the MAPbI₃ lattice than n-BA⁺ , suppressing the formation of unwanted multi-oriented perovskites. These findings well explain the better device performance of 2D perovskite solar cells based on iso-BA⁺ and elucidate the fundamental mechanism of ligand structural impact on 2D perovskite crystallization.

Orientated crystallization of FA-based perovskite via hydrogen-bonded polymer network for efficient and stable solar cells

Incorporating mixed ion is a frequently used strategy to stabilize black-phase formamidinum lead iodide perovskite for high-efficiency solar cells. However, these devices commonly suffer from photoinduced phase segregation and humidity instability. Herein, we find that the underlying reason is that the mixed halide perovskites generally fail to grow into homogenous and high-crystalline film, due to the multiple pathways of crystal nucleation originating from various intermediate phases in the film-forming process. Therefore, we design a multifunctional fluorinated additive, which restrains the complicated intermediate phases and promotes orientated crystallization of α-phase of perovskite. Furthermore, the additives in-situ polymerize during the perovskite film formation and form a hydrogen-bonded network to stabilize α-phase. Remarkably, the polymerized additives endow a strongly hydrophobic effect to the bare perovskite film against liquid water for 5 min. The unencapsulated devices achieve 24.10% efficiency and maintain >95% of the initial efficiency for 1000 h under continuous sunlight soaking and for 2000 h at air ambient of ~50% humid, respectively.

Highly efficient p-i-n perovskite solar cells that endure temperature variations

Daily temperature variations induce phase transitions and lattice strains in halide perovskites, challenging their stability in solar cells. We stabilized the perovskite black phase and improved solar cell performance using the ordered dipolar structure of β-poly(1,1-difluoroethylene) to control perovskite film crystallization and energy alignment. We demonstrated p-i-n perovskite solar cells with a record power conversion efficiency of 24.6% over 18 square millimeters and 23.1% over 1 square centimeter, which retained 96 and 88% of the efficiency after 1000 hours of 1-sun maximum power point tracking at 25° and 75°C, respectively. Devices under rapid thermal cycling between -60° and +80°C showed no sign of fatigue, demonstrating the impact of the ordered dipolar structure on the operational stability of perovskite solar cells.

Recent progress of crystal orientation engineering in halide perovskite photovoltaics

Manipulating the crystallographic orientation of semiconductor crystals plays a vital role in fine-tuning their facet-dependent properties, such as surface properties, charge transfer properties, trap state density, and lattice strain. The success in crystal orientation engineering enables the preferential growth orientation of perovskite thin films with favorable crystal planes by precise nucleation manipulation and growth condition optimization, rendering the films with the unique optoelectronic properties to further improve the efficiency of perovskite solar cells (PSCs). However, the origin and impact of preferential crystallographic orientation of perovskite thin films on the corresponding photovoltaic performance of PSCs are still far from being well understood. Herein, we explore the crystal orientation-dependent optoelectronic properties of halide perovskites and their influence on the photovoltaic performance of PSCs. We summarize the basic strategies for crystal facet engineering in the fabrication of preferentially oriented perovskite thin films, with a focus on the oriented growth mechanism during thin film formation. Based on the above knowledge and the recent research progress in terms of crystal orientation engineering in PSCs, a brief outlook on the remaining challenges and perspectives are provided.

Control of perovskite film crystallization and growth direction to target homogeneous monolithic structures

Getting performant organo-metal halide perovskite films for various application remains challenging. Here, we show the behavior of solvent and perovskite elements for four different perovskites families and nine different initial precursor solution systems in the case of the most popular preparation process which includes an anti-solvent dripping-assisted spin coating of a precursor solution and a subsequent thermal annealing. We show how the initial solution composition affects, first, the film formed by spin coating and anti-solvent dripping and, second, the processes occurring upon thermal annealing, including crystal domain evolution and the grain growth mechanism. We propose a universal typology which distinguishes three types for the growth direction of perovskite crystals: downward (Type I), upward (Type II) and lateral (Type III). The latter results in large, monolithic grains and we show that this mode must be targeted for the preparation of efficient perovskite light absorber thin films of solar cells.

What Can Glow Discharge Optical Emission Spectroscopy (GD-OES) Technique Tell Us about Perovskite Solar Cells?

The emerging broad range of applications of the glow discharge optical emission spectroscopy (GD-OES) technique in the field of perovskite solar cells (PSCs) research is reviewed. It can provide a large palette of information by easily and quickly tracking the depth distribution of light to heavy elements. After a discussion of the advantages and the limitations of the technique and a comparison with other analytical techniques, how GD-OES is employed to give structural information on perovskite solar cells is shown. GD-OES has allowed the full perovskite film formation process investigation, from the initial precursor layers containing soaking and complexed solvent to the final crystallized 3D perovskite layers. The A-site elemental cations distribution is followed-up during the film formation. In addition, this technique gives a deep insight into the action mechanism of additives and their effects on the film formation. It provides fruitful information on optimized light absorbing layers and on the selective contact layers which ensure the charge transport in PSCs. It allows to directly visualize halide ions migration and their blocking by ad-hoc chemical engineering and to study the films and PSCs ageing. GD-OES opens new perspectives to explain the final performances of the devices.

Controllable Heterogenous Seeding-Induced Crystallization for High-Efficiency FAPbI3 -Based Perovskite Solar Cells Over 24

The addition of small seeding particles into a supersaturated solution is one among the most effective approaches to obtain high-quality semiconductor materials via increased crystallization rates. However, limited study is conducted on this approach for the fabrication of perovskite solar cells. Here, a new strategy-"heterogenous seeding-induced crystallization (hetero-SiC)" to assist the growth of FAPbI₃ -based perovskite is proposed. In this work, di-tert-butyl(methyl)phosphonium tetrafluoroborate is directly introduced into the precursor, which forms a low-solubility complex with PbI₂ . The low-solubility complex can serve as the seed to induce crystallization of the perovskite during the solvent-evaporation process. Various in situ measurement tools are used to visualize the hetero-SiC process, which is shown to be an effective way of manipulating the nucleation and crystal growth of perovskites. The hetero-SiC process greatly improves the film quality, reduces film defects, and suppresses nonradiative recombination. A hetero-SIC proof-of-concept device exhibits outstanding performance with 24.0% power conversion efficiency (PCE), well over the control device with 22.2% PCE. Additionally, hetero-SiC perovskite solar cell (PSC) stability under light illumination is enhanced and the PSC retains 84% of its initial performance after 1400 h of light illumination.

Strain effects on halide perovskite solar cells

Halide perovskite solar cells (PSCs) have achieved power conversion efficiencies (PCEs) approaching 26%, however, the stability issue hinders their commercialization. Due to the soft ionic nature of perovskite materials, the strain effect on perovskite films has been recently recognized as one of the key factors that affects their opto-electronic properties and the device stability. Herein, we summarized the origins of strain, characterization techniques, and implications of strain on both perovskite film and solar cells as well as various strategies to control the strain. Finally, we proposed effective strategies for future strain engineering. We believe this comprehensive review could further facilitate researchers with a deeper understanding of strain effect and enhance the research activity in engineering the strain to further improve performance and especially the device stability toward commercialization.

This review systematically describes the origins, characterization and implications of strain in perovskite solar cells and proposes novel control strategies.

Resolving Mixed Intermediate Phases in Methylammonium-Free Sn-Pb Alloyed Perovskites for High-Performance Solar Cells

The complete elimination of methylammonium (MA) cations in Sn-Pb composites can extend their light and thermal stabilities. Unfortunately, MA-free Sn-Pb alloyed perovskite thin films suffer from wrinkled surfaces and poor crystallization, due to the coexistence of mixed intermediate phases. Here, we report an additive strategy for finely regulating the impurities in the intermediate phase of Cs_0.25FA_0.75Pb_0.6Sn_0.4I₃ and, thereby, obtaining high-performance solar cells. We introduced d-homoserine lactone hydrochloride (D-HLH) to form hydrogen bonds and strong Pb-O/Sn-O bonds with perovskite precursors, thereby weakening the incomplete complexation effect between polar aprotic solvents (e.g., DMSO) and organic (FAI) or inorganic (CsI, PbI₂, and SnI₂) components, and balancing their nucleation processes. This treatment completely transformed mixed intermediate phases into pure preformed perovskite nuclei prior to thermal annealing. Besides, this D-HLH substantially inhibited the oxidation of Sn²⁺ species. This strategy generated a record efficiency of 21.61%, with a V_oc of 0.88 V for an MA-free Sn-Pb device, and an efficiency of 23.82% for its tandem device. The unencapsulated devices displayed impressive thermal stability at 85 °C for 300 h and much improved continuous operation stability at MPP for 120 h.

Annealing Engineering in the Growth of Perovskite Grains

Perovskite solar cells (PSCs) are a promising and fast-growing type of photovoltaic cell due to their low cost and high conversion efficiency. The high efficiency of PSCs is closely related to the quality of the photosensitive layer, and the high-quality light absorbing layer depends on the growth condition of the crystals. In the formation of high-quality crystals, annealing is an indispensable and crucial part, which serves to evaporate the solvent and drive the crystallization of the film. Various annealing methods have different effects on the promotion of the film growth process owing to the way they work. Here, this review will present a discussion of the growth puzzles and quality of perovskite crystals under different driving forces, and then explain the relationship between the annealing driving force and crystal growth. We divided the main current annealing methods into physical and chemical annealing, which has never been summarized before. The main annealing methods currently reported for crystal growth are summarized to visualize the impact of annealing design strategies on photovoltaic performance, while the growth mechanisms of thin films under multiple annealing methods are also discussed. Finally, we suggest future perspectives and trends in the industrial fabrication of PSCs in the future. The review promises industrial manufacturing of annealed PSCs. The review is expected to facilitate the industrial fabrication of PSCs.

Vacuum Quenching for Large-Area Perovskite Film Deposition

The removal of precursor solvents in perovskite wet films plays a vital role in controlling the quality of perovskite films and devices. The dripping antisolvent method (removing precursor solvents) has made great advances in small-area devices, but this method limits the preparation of large-area perovskite films. Vacuum quenching that evaporates solvents by dropping the pressure is a potential large-area manufacturing approach. Herein, we have conducted a systematic comparative study on these two methods of depositing perovskite films. It is found that vacuum quenching can obtain the same film quality and small-area device efficiency (∼22.5%) as the antisolvent method. However, on a large-area substrate, the fast vacuum quenching rate improves the solvent evaporation efficiency and nucleation density (i.e., forming a large number of crystal nuclei), thereby obtaining a more uniform and stable perovskite film. Notably, the manufacture window exceeds 10 min. As a result, the champion large-area (6 × 6 cm²) perovskite solar module exhibits an impressive efficiency (17.86%) and long-term operational stability. Furthermore, coupling slot-die coating, vacuum quenching can realize the industrial continuous deposition of large-area perovskite films, which is a potential route for large-scale production.

Growth and Degradation Kinetics of Organic-Inorganic Hybrid Perovskite Films Determined by In Situ Grazing-Incidence X-Ray Scattering Techniques

Organic-inorganic halide perovskite (OIHP) solar cells hold a great promise for commercial breakthrough since their power conversion efficiency has been pushed beyond the mark of 25%, making them capable of competing with traditional crystalline silicon solar cells. The key to achieve efficient and stable perovskite solar cells is inherently related to the film morphology. The understanding of the kinetic processes of film formation and degradation opens up possibilities to tailor the film morphology via the regulation of precursor and processing parameters. In situ grazing-incidence X-ray scattering (GIXS) techniques allow for tracking the morphology evolution of thin films at different length scales and with high temporal resolution. In this review, the selected examples for application of in situ grazing-incidence wide-angle X-ray scattering and grazing-incidence small-angle X-ray scattering techniques to the growth and stability of OIHPs are summarized after a brief introduction to both techniques, highlighting particularly the morphological evolution of perovskite films over time. Then the correlated mathematical models are reviewed to give a toolbox for analyzing the mechanisms of film formation and degradation. Thus, an overview on the in situ GIXS methods is linked to the research of OIHP kinetics.

A Systematic Review of Metal Halide Perovskite Crystallization and Film Formation Mechanism Unveiled by In Situ GIWAXS

Metal halide perovskites are of fundamental interest in the research of modern thin-film optoelectronic devices, owing to their widely tunable optoelectronic properties and solution processability. To obtain high-quality perovskite films and ultimately high-performance perovskite devices, it is crucial to understand the film formation mechanisms, which, however, remains a great challenge, due to the complexity of perovskite composition, dimensionality, and processing conditions. Nevertheless, the state-of-the-art in situ grazing-incidence wide-angle X-ray scattering (GIWAXS) technique enables one to bridge the complex information with device performance by revealing the crystallization pathways during the perovskite film formation process. In this review, the authors illustrate how to obtain and understand in situ GIWAXS data, summarize and assess recent results of in situ GIWAXS studies on versatile perovskite photovoltaic systems, aiming at elucidating the distinct features and common ground of film formation mechanisms, and shedding light on future opportunities of employing in situ GIWAXS to study the fundamental working mechanisms of highly efficient and stable perovskite solar cells toward mass production.

Performance-limiting formation dynamics in mixed-halide perovskites

Wide-bandgap (WBG) mixed-halide perovskites as the front cell absorber are accomplishing perovskite-based tandem solar cells with over 29% power conversion efficiency. However, their large voltage deficits limit their ultimate performance. Only a handful of studies probe the fundamental mechanisms underlying the voltage deficits, which remain an unsolved challenge in the field. In this study, we investigate the formation dynamics and defect physics of WBG mixed-halide perovskites in contrast with their corresponding triiodide-based perovskites. Our results show that the inclusion of bromide introduced a halide homogenization process that occurs during the perovskite growth stage from an initial bromide-rich phase toward the final target stoichiometry. We further elucidated a physical model that correlates the role of bromide with the formation dynamics, defect physics, and eventual optoelectronic properties of the film. This work provides a fundamental and unique perspective toward understanding the performance-limiting factors affecting WBG mixed-halide perovskites.

Synergistic Effects of Eu-MOF on Perovskite Solar Cells with Improved Stability

Enhancing device lifetime is one of the essential challenges in perovskite solar cells. The ultrathin Eu-MOF layer is introduced at the interface between the electron-transport layer and the perovskite absorber to improve the device stability. Both Eu ions and organic ligands in the MOF can reduce the defect concentration and improve carrier transport. Moreover, due to the Förster resonance energy transfer effect, Eu-MOF in perovskite films can improve light utilization and reduce the decomposition under ultraviolet light. Meanwhile, Eu-MOF also turns tensile strain to compressive strain in the perovskite films. As a result, the corresponding devices achieve a champion power conversion efficiency (PCE) of 22.16%. In addition, the devices retain 96% of their original PCE after 2000 h under the relative humidity of 30% and 91% of their original PCE after 1200 h after continuous 85 °C aging condition in N₂ .

The Impact of Solvent Vapor on the Film Morphology and Crystallization Kinetics of Lead Halide Perovskites during Annealing

One of the key factors for the remarkable improvements of halide perovskite solar cells over the last few years is the increased control over perovskite crystallinity and its thin film morphology. Among various processing methods, solvent vapor-assisted annealing (SVAA) has proven to be promising in achieving high-quality perovskite films. However, a comprehensive understanding of the perovskite crystallization process during SVAA is still lacking. In this work, we use a home-built setup to precisely control the SVAA conditions to investigate in detail the perovskite crystallization kinetics. By changing the solvent vapor concentration during annealing, the perovskite grain size can be tuned from 200 nm to several micrometers. We monitor the crystallization kinetics during solvent-free annealing and SVAA using in situ grazing incidence wide-angle X-ray scattering, where we find a diminished perovskite growth rate and the formation of low dimensional perovskite at the top of the perovskite layer during SVAA. Scanning electron microscopy images of the final films further suggest that the perovskite growth follows an Ostwald ripening process at higher solvent concentrations. Thus, our results will contribute to achieve a more targeted processing of perovskite films.

Out-of-equilibrium processes in crystallization of organic-inorganic perovskites during spin coating

Complex phenomena are prevalent during the formation of materials, which affect their processing-structure-function relationships. Thin films of methylammonium lead iodide (CH₃NH₃PbI₃, MAPI) are processed by spin coating, antisolvent drop, and annealing of colloidal precursors. The structure and properties of transient and stable phases formed during the process are reported, and the mechanistic insights of the underlying transitions are revealed by combining in situ data from grazing-incidence wide-angle X-ray scattering and photoluminescence spectroscopy. Here, we report the detailed insights on the embryonic stages of organic-inorganic perovskite formation. The physicochemical evolution during the conversion proceeds in four steps: i) An instant nucleation of polydisperse MAPI nanocrystals on antisolvent drop, ii) the instantaneous partial conversion of metastable nanocrystals into orthorhombic solvent-complex by cluster coalescence, iii) the thermal decomposition (dissolution) of the stable solvent-complex into plumboiodide fragments upon evaporation of solvent from the complex and iv) the formation (recrystallization) of cubic MAPI crystals in thin film.

Complex phenomena are prevalent during the formation of materials, and they affect the processing structure-function relationship. Here the authors elucidate the stochastic transformation processes happening during the spin coating of perovskite colloidal precursors by multimodal characterization.

Organic Matrix Assisted Low-temperature Crystallization of Black Phase Inorganic Perovskites

All-inorganic perovskites have attracted increasing attention for applications in perovskite solar cells (PSCs) and optoelectronics, including light-emitting devices (LEDs). Cesium lead halide perovskites with tunable I/Br ratios and a band gap aligning with the sunlight region are promising candidates for PSCs. Although impressive progress has been made to improve device efficiency from the initial 2.9 % with low phase stability to over 20 % with high stability, there are still questions regarding the perovskite crystal growth mechanism, especially at low temperatures. In this Minireview, we summarize recent developments in using an organic matrix, including the addition and use of organic ions, polymers, and solvent molecules, for the crystallization of black phase inorganic perovskites at temperatures lower than the phase transition point. We also discuss possible mechanisms for this low-temperature crystallization and their effect on the stability of black phase perovskites. We conclude with an outlook and perspective for further fabrication of large-scale inorganic perovskites for optoelectronic applications.

Unveiling the additive-assisted oriented growth of perovskite crystallite for high performance light-emitting diodes

Solution-processed metal halide perovskites have been recognized as one of the most promising semiconductors, with applications in light-emitting diodes (LEDs), solar cells and lasers. Various additives have been widely used in perovskite precursor solutions, aiming to improve the formed perovskite film quality through passivating defects and controlling the crystallinity. The additive's role of defect passivation has been intensively investigated, while a deep understanding of how additives influence the crystallization process of perovskites is lacking. Here, we reveal a general additive-assisted crystal formation pathway for FAPbI3 perovskite with vertical orientation, by tracking the chemical interaction in the precursor solution and crystallographic evolution during the film formation process. The resulting understanding motivates us to use a new additive with multi-functional groups, 2-(2-(2-Aminoethoxy)ethoxy)acetic acid, which can facilitate the orientated growth of perovskite and passivate defects, leading to perovskite layer with high crystallinity and low defect density and thereby record-high performance NIR perovskite LEDs (~800 nm emission peak, a peak external quantum efficiency of 22.2% with enhanced stability).

Bottom-Up Quasi-Epitaxial Growth of Hybrid Perovskite from Solution Process-Achieving High-Efficiency Solar Cells via Template​-Guided Crystallization

Epitaxial growth gives the highest-quality crystalline semiconductor thin films for optoelectronic devices. Here, a universal solution-processed bottom-up quasi-epitaxial growth of highly oriented α-formamidinium lead triiodide (α-FAPbI₃ ) perovskite film via a two-step method is reported, in which the crystal orientation of α-FAPbI₃ film is precisely controlled through the synergetic effect of methylammonium chloride and the large-organic cation butylammonium bromide. In situ GIWAXS visualizes the BA-related intermediate phase formation at the bottom of film, which serves as a guiding template for the bottom-up quasi-epitaxial growth in the subsequent annealing process. The template-guided epitaxially grown BAFAMA perovskite film exhibits increased crystallinity, preferred crystallographic orientation, and reduced defects. Moreover, the BAFAMA perovskite solar cells demonstrate decent stability, maintaining 95% of their initial power conversion efficiency after 2600 h ambient storage, and 4-time operation condition lifetime enhancement.

Stabilizing black-phase formamidinium perovskite formation at room temperature and high humidity

The stabilization of black-phase formamidinium lead iodide (α-FAPbI3) perovskite under various environmental conditions is considered necessary for solar cells. However, challenges remain regarding the temperature sensitivity of α-FAPbI3 and the requirements for strict humidity control in its processing. Here we report the synthesis of stable α-FAPbI3, regardless of humidity and temperature, based on a vertically aligned lead iodide thin film grown from an ionic liquid, methylamine formate. The vertically grown structure has numerous nanometer-scale ion channels that facilitate the permeation of formamidinium iodide into the lead iodide thin films for fast and robust transformation to α-FAPbI3. A solar cell with a power-conversion efficiency of 24.1% was achieved. The unencapsulated cells retain 80 and 90% of their initial efficiencies for 500 hours at 85°C and continuous light stress, respectively.

Visualization of halide perovskite crystal growth processes by in situ heating WAXS measurements

We observed the crystallization dynamics of halide perovskite crystals (CH3NH3PbI3) by in situ heating wide-angle X-ray scattering measurements. As a result, we revealed that crystal growth occurs during the conversion of complexes to perovskite crystals.