Laminated Hybrid Junction of Sulfur-Doped TiO2 and a Carbon Substrate Derived from Ti3C2 MXenes: Toward Highly Visible Light-Driven Photocatalytic Hydrogen Evolution

A Facile Strategy for the Preparation of N-Doped TiO2 with Oxygen Vacancy via the Annealing Treatment with Urea

Although titanium dioxide (TiO2) has a wide range of potential applications, the photocatalytic performance of TiO2 is limited by both its limited photoresponse range and fast recombination of the photogenerated charge carriers. In this work, the preparation of nitrogen (N)-doped TiO2 accompanied by the introduction of oxygen vacancy (Vo) has been achieved via a facile annealing treatment with urea as the N source. During the annealing treatment, the presence of urea not only realizes the N-doping of TiO2 but also creates Vo in N-doped TiO2 (N-TiO2), which is also suitable for commercial TiO2 (P25). Unexpectedly, the annealing treatment-induced decrease in the specific surface area of N-TiO2 is inhibited by the N-doping and, thus, more active sites are maintained. Therefore, both the N-doping and formation of Vo as well as the increased active sites contribute to the excellent photocatalytic performance of N-TiO2 under visible light irradiation. Our work offers a facile strategy for the preparation of N-TiO2 with Vo via the annealing treatment with urea.

Laser-Treated MXene as an Electrochemical Agent to Boost Properties of Semitransparent Photoelectrode Based on Titania Nanotubes

In this study, Ti3C2Tx underwent laser treatment to reshape it, resulting in the formation of a TiO2/Ti3C2Tx heterojunction. The interaction with laser light induced the formation of spherical TiO2 composed of an anatase-rutile phase on the Ti3C2Tx surface. Such a heterostructure was loaded over a titania nanotube (TNT) layer, and the surface area was enhanced through immersion in a TiCl4 solution followed by thermal treatment. Consequently, the photon-to-electron conversion efficiency exhibits a 10-fold increase as compared to bare TNT. Moreover, for the sample produced with optimized conditions, five times higher photoactivity is observed in comparison to bare TNT. It was shown that under visible light irradiation the most photoactive heterojunction based on the tubular layer reveals a substantial drop in the charge transfer resistance of about 32% with respect to the dark condition. This can be attributed to the narrower band gaps of the modified material and improvement of the separation efficiency of the photogenerated electron-hole pairs. Overall results suggest that this investigation underscores TiO2/Ti3C2Tx as a promising noble-metal-free material that enhances both the electrochemical and photoelectrochemical performances of electrode materials based on TNT that can be further used in light-harvesting applications.

"Visualization" Gas-Gas Sensors Based on High Performance Novel MXenes Materials

The detection of toxic, harmful, explosive, and volatile gases cannot be separated from gas sensors, and gas sensors are also used to monitor the greenhouse effect and air pollution. However, existing gas sensors remain with many drawbacks, such as lower sensitivity, lower selectivity, and unstable room temperature detection. Thus, there is an imperative need to find more suitable sensing materials. The emergence of a new 2D layered material MXenes has brought dawn to solve this problem. The multiple advantages of MXenes, namely high specific surface area, enriched terminal functionality groups, hydrophilicity, and good electrical conductivity, make them among the most prolific gas-sensing materials. Therefore, this review paper describes the current main synthesis methods of MXenes materials, and focuses on summarizing and organizing the latest research results of MXenes in gas sensing applications. It also introduces the possible gas sensing mechanisms of MXenes materials on NH3 , NO2 , CH3 , and volatile organic compounds (VOCs). In conclusion, it provides insight into the problems and upcoming challenges of MXenes materials for gas sensing.

Non-Lignin Constructing the Gas-Solid Interface for Enhancing the Photothermal Catalytic Water Vapor Splitting

The progress of solar-driven water-splitting technology has been impeded by the limited light response capability of semiconductor materials. Despite attempts to leverage nearly 50% of infrared radiation for photothermal synergy and catalytic reaction enhancement, heat loss during liquid phase reactions results in low energy conversion efficiency. Here, the photothermally driven catalytic water-splitting system, which designs K-SrTiO3 -loaded TiN silica wool at the water-air interface. Photocatalytic tests and density functional theory calculations demonstrate that the thermal effect transforms liquid water into water vapor, thereby reducing the reaction free energy of catalysts and improving the transmission rate of catalytic products. Hence, the hydrogen evolution rate reaches 275.46 mmol m-2  h-1 , and the solar-to-hydrogen (STH) efficiency is 1.81% under 1 sun irradiation in this gas-solid system, which is more than twice that of liquid water splitting. This novel photothermal catalytic pathway, which involves a coupled reaction of water evaporation and water splitting, is anticipated to broaden the utilization range of the solar spectrum and significantly enhance the conversion efficiency of STH.

Metal ion assistant transformation strategy to synthesize catechol-based metal-organic frameworks from Ti3C2Tx precursors

Chemical transformation strategy is capable of fabricating nanomaterials with well-defined structures and fascinating performance via controllable crystallization kinetics in the phase transformation. V2CTx MXene has been used as precursors to fabricate vanadium porphyrin metal-organic frameworks (V-PMOFs) via the coordination of deprotonated carboxylic acid ligands. However, the rational and in-depth exploration of synthesis mechanism with the aim of enriching the variety of MXene (i.e., Ti3C2Tx) and organic ligands (i.e., catechol-based) to design new MOFs is rarely reported. Herein, we have first developed a metal ion assistant transformation strategy to synthesize three-dimensional catechol-based TiCu-HHTP (HHTP = 2,3,6,7,10,11-hexahydroxytriphenylene) MOFs with a non-interpenetrating SrSi2 (srs) framework using two-dimensional Ti3C2Tx as precursors. The unique synergetic transformation mechanism involves the electron transfer from Ti3C2Tx to electrostatically adsorbed Cu2+ ion for redox reaction, the subsequent Ti-C bond rupture for Ti4+ ion release, and the continuous chelation coordination between Ti4+/Cu2+ and HHTP. Ti3C2Tx precursors and auxiliary metal ion could be rationally substituted by V2CTx and Mn+ (e.g., Ni2+, Co2+, Mn2+, and Zn2+), respectively. This strategy lays the foundation for the design and synthesis of innovative and multifarious MOFs derived from MXene or other unconventional metal precursors.

Enhanced photocatalytic activity of Fe-, S- and N-codoped TiO2 for sulfadiazine degradation

The composite material based on N-, S-, and Fe-doped TiO2 (NSFe-TiO2) synthesized by wet impregnation was used as a photocatalyst to rapidly degrade sulfadiazine. The photocatalytic degradation behavior and mechanism of sulfadiazine on NSFe-TiO2 were investigated for revealing the role of degradation under ultraviolet light. The results showed that compared with TiO2, NSFe-TiO2 markedly improved the efficiency in photocatalytic degradation of sulfadiazine: more than 90% of sulfadiazine could be removed within 120 min by NSFe-TiO2 dosage of 20 mg L-1. The process conformed to first-order reaction kinetics model. The parameters such as loaded amount of NSFe-TiO2, solution pH value, humic acid concentration and recycle numbers on removal efficiency were also studied. Compared to neutral and alkaline conditions, acidic condition was not conducive to the photocatalysis. HA, Ca2+, Cu2+ and Zn2+ in the actual water body had mild inhibition on sulfadiazine degradation in UV/NSFe-TiO2 system. Fragments screened by high-resolution mass spectrometry were conducted to explore the oxidation mechanism and pathways of sulfadiazine degradation. On the whole, UV/NSFe-TiO2 photocatalysis has a good effect on sulfadiazine removal.

Supplementary Information

The online version contains supplementary material available at 10.1007/s13762-023-04771-6.

Modification of TiO2 nanotubes by graphene-strontium and cobalt molybdate perovskite for efficient hydrogen evolution reaction in acidic medium

Herein, we demonstrate that modification of TiO₂ nanotubes with graphene-strontium and cobalt molybdate perovskite can turn them into active electrocatalysts for hydrogen evolution reaction (HER). For this purpose, a simple method of hydrothermal synthesis of perovskites was developed directly on the TiO₂ nanotubes substrate. Moreover, the obtained hybrids were also decorated with graphene oxide (GO) during one-step hydrothermal synthesis. The obtained materials were characterized by scanning electron microscopy with energy dispersive X-ray analysis, Raman spectroscopy, and X-ray diffraction analysis. Catalytic properties were verified by electrochemical methods (linear voltammetry, chronopotentiometry). The obtained hybrids were characterized by much better catalytic properties towards hydrogen evolution reaction compared to TiO₂ and slightly worse than platinum. The optimized hybrid catalyst (decorated by GO) can drive a cathodic current density of 10 mA cm^-2 at an overpotential of 121 mV for HER with a small Tafel slope of 90 mV dec^-1 in 0.2 M H₂SO₄.

A study on the role of plasmonic Ti3C2Tx MXene in enhancing photoredox catalysis

Engineering the spatial separation and transfer of photogenerated charge carriers has been one of the most enduring research topics in the field of photocatalysis due to its crucial role in determining the performances of photocatalysts. Herein, as a proof-of-concept, Ti₃C₂T_x MXene is coupled with a typical heterojunction of TiO₂@CdS through a co-assembly strategy to boost electron pumping towards improving the photocatalytic efficiency. In addition to the band alignment-mediated electron transfer in TiO₂@CdS-Ti₃C₂T_x heterojunctions, the plasmon-induced electric field enhancement of Ti₃C₂T_x is found to cooperate with the electron-reservoir role of Ti₃C₂T_x to extract photoinduced electrons. The synergistic dual functions of Ti₃C₂T_x promote multichannel electron transfer in TiO₂@CdS-Ti₃C₂T_x hybrids to improve the photocatalytic efficiency. These results intuitively show that there is a wide scope to manipulate the spatial separation and transfer of photoinduced electrons by cultivating the fertile ground of Ti₃C₂T_x toward boosting the efficiency of solar-to-chemical conversion.

S- and N-Co-Doped TiO2-Coated Al2O3 Hollow Fiber Membrane for Photocatalytic Degradation of Gaseous Ammonia

This study successfully prepared and tested sulfur- and nitrogen-co-doped TiO₂-coated α-Al₂O₃ (S,N-doped TiO₂/Al₂O₃) hollow fiber (HF) membranes for efficient photocatalytic degradation of gaseous ammonia (NH₃). Thiourea was used as a sulfur- and nitrogen-doping source to produce a S,N-doped TiO₂ photocatalyst powder. For comparative purposes, undoped TiO₂ powder was also synthesized. Through the application of a phase-inversion technique combined with high-temperature sintering, hollow fibers composed of α-Al₂O₃ were developed. Undoped TiO₂ and S,N-doped TiO₂ photocatalyst powders were coated on the α-Al₂O₃ HF surface to obtain undoped TiO₂/Al₂O₃ and S,N-doped TiO₂/Al₂O₃ HF membranes, respectively. All prepared samples were characterized using XRD, TEM, XPS, UV-Vis, SEM, BET, FT-IR, and EDS. S and N dopants were confirmed using XPS and UV-Vis spectra. The crystal phase of the undoped TiO₂ and S,N-doped TiO₂ photocatalysts was a pure anatase phase. A portable air purifier photocatalytic filter device was developed and tested for the first time to decrease the amount of indoor NH₃ pollution under the limits of the lachrymatory threshold. The device, which was made up of 36 S,N-doped TiO₂/Al₂O₃ HF membranes, took only 15-20 min to reduce the level of NH₃ in a test chamber from 50 ppm to around 5 ppm, confirming the remarkable performance regarding the photocatalytic degradation of gaseous NH₃.

A bionic solar-driven interfacial evaporation system with a photothermal-photocatalytic hydrogel for VOC removal during solar distillation

Solar-driven interfacial evaporation is a breakthrough water treatment method because it harvests solar energy for producing clean water. However, evaporated volatile organic compounds (VOCs) in distilled water are the greatest barrier to this technology. Herein, a bionic solar-driven interfacial evaporation system integrating photothermal and photocatalysis technology was developed based on a new combined material TiO₂/Ti₃C₂/C₃N₄/PVA (TTCP) hydrogel as an evaporator. Phenol-contaminated water, especially actual water (seawater, lake water and reclaimed water), is used to evaluate the water evaporation and VOC photocatalytic degradation performance. The results show that the evaporation rate of TTCP hydrogel was 1.54 kg m ^- 2h ^- 1 under 1 kW m ^- 2, and the removal efficiency of phenol ranged from 69.4% to 100% at different concentrations (1-50 mg/L) in source water. Particularly, the capacity of the bionic evaporator was first evaluated for different types of actual water. Despite the initial TOC (38.12-57.93 mg/L) and total dissolved solids (TDS, 1.35×10³-8.78×10⁴ mg/L) for seawater, lake water and reclaimed water being very different, the TDS was decreased by more than two orders of magnitude, below the US EPA drinking water standard (500 mg/L). The maximum TOC removal efficiency reached 80% under simulated sunlight (1 kW m ^- 2), which is comparable to the efficiency of the ultrafiltration technique previously reported except for seawater. Furthermore, real sunlight (average solar irradiation ∼0.82 kW m^{- 2}) was used to assess the practicability. The bionic evaporator can produce 0.72 kg m ^- 2h ^- 1 of vapor from reclaimed water and run with steadily efficient TDS and TOC removals, reaching 99% and 74%, respectively. This technology, as a small, decentralized water treatment method, is a good choice for remote and off-grid areas.

In Situ Growth Intercalation Structure MXene@Anatase/Rutile TiO2 Ternary Heterojunction with Excellent Phosphoprotein Detection in Sweat

Abnormal protein phosphorylation may relate to diseases such as Alzheimer's, schizophrenia, and Parkinson's. Therefore, the real-time detection of phosphoproteins in sweat was of great significance for the early knowledge, detection, and treatment of neurological diseases. In this work, anatase/rutile TiO₂ was in situ grown on the MXene surface to constructing the intercalation structure MXene@anatase/rutile TiO₂ ternary heterostructure as a sensing platform for detecting phosphoprotein in sweat. Here, the intercalation structure of MXene acted as electron and diffusion channels for phosphoproteins. The in situ grown anatase/rutile TiO₂ with n-n-type heterostructure provided specific adsorption sites for the phosphoproteins. The determination of phosphoprotein covered concentrations in sweat, with linear range from 0.01 to 1 mg/mL, along with a low LOD of 1.52 μM. It is worth noting that, since the macromolecular phosphoprotein was adsorbed on the surface of the material, the electrochemical signal gradually decreased with the increase of phosphoprotein concentration. In addition, the active sites in the MXene@anatase/rutile TiO₂ ternary heterojunction and synergistic effect of the heterojunction were verified by first-principle calculations to further realize the response to phosphoproteins. Additionally, the effective diffusion capacity and mobility of phosphoprotein molecules in the ternary heterojunction structure were studied by molecular dynamics simulation. Furthermore, the constructed sensing platform showed high selectivity, repeatability, reproducibility, and stability, and this newly developed sensor can detect for phosphoprotein in actual sweat samples. This satisfactory sensing strategy could be promoted to realize the noninvasive and continuous detection of sweat.

Noble-Nanoparticle-Decorated Ti3C2T x MXenes for Highly Sensitive Volatile Organic Compound Detection

Two-dimensional transition-metal carbides and nitrides (MXenes) have been regarded as promising sensing materials because of their high surface-to-volume ratios and outstanding electronic, optical, and mechanical properties with versatile transition-metal and surface chemistries. However, weak gas-molecule adsorption of MXenes poses a serious limitation to their sensitivity and selectivity, particularly for trace amounts of volatile organic compounds (VOCs) at room temperature. To deal with these issues, Au-decorated MXenes are synthesized by a facile solution mixing method for room-temperature sensing of a wide variety of oxygen-based and hydrocarbon-based VOCs. Dynamic sensing experiments reveal that optimal decoration of Au nanoparticles (NPs) on Ti₃C₂T _x MXene significantly elevates the response and selectivity of the flexible sensors, especially in detecting formaldehyde. Au-Ti₃C₂T _x gas sensors exhibited an extremely low limit of detection of 92 ppb for formaldehyde at room temperature. Au-Ti₃C₂T _x provides reliable gas response, low noise level, ultrahigh signal-to-noise ratio, high selectivity, as well as parts per billion level of formaldehyde detection. The prominent mechanism for Au-Ti₃C₂T _x in sensing formaldehyde is elucidated theoretically from density functional theory simulations. The results presented here strongly suggest that decorating noble-metal NPs on MXenes is a feasible strategy for the development of next-generation ultrasensitive sensors for Internet of Things.

In-Situ Fabricating V2O5/TiO2-Carbon Heterojunction from Ti3C2 MXene as Highly Active Visible-Light Photocatalyst

Titanium dioxide is a mainstream photocatalyst, but it still confronts great obstacles of poor visible light absorption and rapid recombination rate of photogenerated carriers. Herein, we describe the design of a highly active visible-light photocatalytic system of graphited carbon layers anchored V2O5/TiO2 heterojunctions derived from Ti3C2 MXene, which demonstrates about 4.58 and 2.79 times higher degradation activity of MB under visible light (λ > 420 nm) than pure V2O5 and TiO2-carbon. Combined with the characterization results, the formed V2O5/TiO2 heterojunction promotes the separation of photogenerated carriers, while the graphitized carbon derived from MXene acts as an electronic reservoir to enhance the absorption of visible light. The ESR results show that superoxide radicals and hydroxyl radicals are the main active species in the reaction system. Therefore, we propose a possible mechanism model to provide a feasible idea for the subsequent design of high-efficiency photocatalysts for environmental treatment.

Rationally designed Ti3C2/N, S-TiO2/g-C3N4 ternary heterostructure with spatial charge separation for enhanced photocatalytic hydrogen evolution

The charge separation and transfer are the major issues dominating the under-laying energy conversion mechanism for photocatalytic system. Construction of semiconductor-based heterojunction system considered to be viable option for boosting the spatial charge separation and transfer in the photocatalytic water splitting system. Here, we design a ternary heterojunction of Ti₃C₂/N, S-TiO₂/g-C₃N₄ by thermal annealing and ultrasonic assisted impregnation method having a well-designed n-n heterojunction and noble metal free Schottky junction for adequate hydrogen evolution. The optimal content of 4 wt% Ti₃C₂ on N, S-TiO₂/g-C₃N₄ (4-TC/NST/CN) exhibit the highest rate of hydrogen generation 495.06μ mol h^-1 which is 3.1, 4.1 and 1.6 fold higher than the pristine N, S doped-TiO₂, g-C₃N₄ and binary hybrid (N, S doped-TiO₂/g-C₃N₄) respectively, with 7% apparent conversion efficiency (ACE). The increment in the activity is described to the robust photogenerated carrier separation and double charge transfer channels because of the formation of dual heterojunction (n-n heterojunction and Schottky junction). XRD and Raman results revealed the occupancy of Ti₃C₂ in the heterojunction due to the strong interaction between Ti₃C_2, with N, S doped-TiO₂ and g-C₃N₄. The HRTEM analysis confirmed the formation of close interfacial junction between the Ti₃C₂, N, S doped-TiO₂ and g-C₃N₄. Moreover, the higher photocurrent, low PL intensity and lower impedance arc suggested the lower charge carrier recombination rate in 4-TC/NST/CN heterojunction. This work represents a significant development to establish a sound foundation for future design of MXene-based ternary hybrid system towards significant charge carrier separation and transfer for H₂ production activity.

Activation of Cadmium–Imidazole Buffering Coordination Polymer by Sulfur-Doping for the Enhancement of Photocatalytic Degradation of Cationic and Anionic Dyes Under Visible Light

The buffering Cadmium–Imidazole Coordination Polymer (Cd–Im-CP) was synthesized hydrothermally from cadmium chloride and imidazole at 70 °C and then was subjected to doping- by the non-metal sulfur using Na2S solution as a novel modification strategy to produce S–Cd–Im CPs. To investigate doping nature and its effects, Cd–Im CP and S–Cd–Im CPs were characterized applying different analyses techniques, FTIR, Raman, PXRD, SEM/EDX, TGA, and UV–Vis DRS analyses. Characterizations showed the successful chemical doping of sulfur. The inclusion of sulfur within chemical CP structure caused narrowing of material’s bandgap from 4.55 and 3.4 eV to 4.25 and 2.35 eV for S–Cd–Im CPs allowing it for photoresponse towards Visible-light. Both Cd–Im CP and S–Cd–Im CPs were applied for photocatalytic degradation of the selected dyes methylene blue (MB),and methyl orange (MO) employing visible and UV irradiations considering three different initial pH levels to investigate the consequence of sulfur doping. After eliminating the photolysis effect, the best degradation by S–Cd–Im CPs was recorded for MB at initial pH 4 being 13 fold that is for Cd–Im CP. The highest apparent turnover frequencies are 1.2 × 10−3 h−1 for MB at initial pH 10 and 1.03 × 10−4 h−1 for MO at initial pH 4 are given by 10S–Cd–IM CP under Visible-light. Generally, S–Cd–Im CPs remarkably improved photocatalysis degradation of both the dyes for all initial pH levels under Visible-light.

Ionic liquid exfoliated Ti3C2Tx MXene nanosheets for photoacoustic imaging and synergistic photothermal/chemotherapy of cancer

Ti₃C₂T_x MXene is a new type of two-dimensional material with good biocompatibility and a good photothermal effect, and shows great potential in cancer treatment. In this study, few-layer ionic liquid (IL)-Ti₃C₂T_x MXene nanosheets were synthesized using IL stripping technology, which have high chemical stability, and allow photoacoustic imaging and synergistic photothermal/chemotherapy of cancer. Under 808 nm laser irradiation, the nanosheets have strong absorption in the near-infrared region, and high photothermal conversion efficiency (∼63.91%). Using DOX as a model drug, the IL-Ti₃C₂T_x MXene@DOX nanosheets exhibited high drug loading capacity and pH-/photosensitivity, which will further promote the drug release of the nanosheets in an acidic tumor microenvironment and under 808 nm laser irradiation. In vitro and in vivo experiments showed that IL-Ti₃C₂T_x MXene@DOX has good biological safety, allows remarkable photoacoustic imaging, and can effectively kill cancer cells with synergistic photothermal/chemotherapy. Therefore, IL-Ti₃C₂T_x MXene nanosheets are expected to provide powerful and useful two-dimensional nanoplatforms for various biomedical applications.

Fabrication of a high-efficiency CdS@TiO2@C/Ti3C2 composite photocatalyst for the degradation of TC-HCl under visible light

CdS@TiO2@C/Ti3C2 composites derived from Ti3C2 MXene exhibit outstanding photodegradation ability for TC-HCl under visible light irradiation.

Synthesis of atomic form nickel co-catalysts on TiO2 for improved photocatalysis by RAFT technique

Using the high incompatibility between the neutral stabilizer body and the block polyelectrolyte to drive phase separation during polymerization-induced self-assembly, a modular approach to systematically adjust ionic monomer/polymer solubility was...

Two-dimensional Ti3C2 MXene-based nanostructures for emerging optoelectronic applications

Since the first discovery of Ti₃C₂ in 2011, two-dimensional (2D) transition-metal carbides, carbonitrides and nitrides, known as MXenes, have attracted significant attention. Due to their outstanding electronic, optical, mechanical, and thermal properties, versatile structures and surface chemistries, Ti₃C₂ MXenes have emerged as new candidates with great potential for applications in optoelectronic devices, such as photovoltaics, photodetectors and photoelectrochemical devices. The excellent metallic conductivity, high anisotropic carrier mobility, good structural and chemical stabilities, high optical transmittance, excellent mechanical strength, tunable work functions, and wide range of optical absorption properties of Ti₃C₂ MXene nanostructures are the key to their success in a number of electronic and photonic device applications. Herein, we summarize the fundamental properties and preparation of pure Ti₃C₂ MXenes, functionalized Ti₃C₂ MXenes and their hybrid nanocomposites, as well as their optoelectronic applications. In the end, the perspective and current challenges of Ti₃C₂ MXenes toward the development of advanced MXene-based nanostructures are briefly discussed for future optoelectronic applications.

Functional Group Modification and Bonding Characteristics of Ti3 C2 MXene-Organic Composites from First-Principles Calculations

The unique physical structure and abundant surface functional groups of MXene make the grafted organic molecules exhibit specific electrical and optical properties. This work reports the results of first-principles calculations to investigate the composite systems formed by different organic molecular monomers, namely acrylic acid (AA), acrylamide (AM), 1-aziridineethanol (1-AD) and glucose, and Ti₃ C₂ MXene saturated with different functional groups, namely -OH, -O and -F. The results show that the interaction between organic molecules and the MXene surface depends on the type of functional groups of the organic molecules, while the strength of the interaction is determined by the type of surface functional groups and the number of hydrogen bonds. The bare Ti₃ C₂ and Ti₃ C₂ (OH)₂ can readily form strong chemical and hydrogen bonds with AA and AM molecules, leading to strong adsorption energy and a large amount of charge transfer, while the interaction between organic molecules and MXene saturated by -F or -O groups mainly exhibits physical interactions, accompanied by low adsorption energy and a small amount of charge transfer. This research provides theoretical guidance for the synthesis of high-performance MXene organic composite systems.

Photocatalytic degradation of ranitidine and reduction of nitrosamine dimethylamine formation potential over MXene-Ti3C2/MoS2 under visible light irradiation

Photocatalysis is an effective method to degrade ranitidine (RAN), which is a typical precursor of nitrosamine dimethylamine (NDMA), an extremely potent human carcinogen. Herein, MXene-Ti₃C₂/MoS₂ composites were prepared by a hydrothermal treatment aiming to use them for the photocatalytic degradation of RAN and the reduction of NDMA formation potential (NDMA-FP) under visible light irradiation for the first time. The analysis of the morphology, chemical composition and structure of these composites as well as the results of electrochemical experiments showed that a heterojunction was formed between MoS₂ and Ti₃C₂, which facilitated the separation of electron-hole pairs and charge transfer, and thereby the photocatalytic performance. The MXene-Ti₃C₂/MoS₂ composite (MT-4) exhibited the best photocatalytic performance in 60 min, with the highest RAN degradation and mineralization efficiencies of 88.4% and 73.58%, and the lowest NDMA-FP of 2.01%. Active species, including •O₂^- radicals, h⁺ and •OH radicals, all contributed to the degradation of RAN, among which •OH radicals were the main active species involved in the photocatalytic activity. The mechanism of the photocatalytic degradation of RAN over MXene-Ti₃C₂/MoS₂ photocatalyst under visible light irradiation was proposed. This work opens up a new perspective on the applications of MXene-based materials for photocatalytic degradation of challenging pollutants.

MXenes as Superexcellent Support for Confining Single Atom: Properties, Synthesis, and Electrocatalytic Applications

Single atom catalysts (SACs) have shown their noticeable potential and gradually become a new favorite in catalytic field due to the particular selectivity, high catalytic performance, and strong durability. The most important factor in the synthesis of SACs is the selection of appropriate support and formation of metal-support interaction. Among a large number of nanomaterials, MXenes can be utilized as benign supports for fixing SACs because of their expansive specific surface area, regulable bandgap, superior electronic conductivity, and strong mechanical stability. The structure and property of MXenes can be manipulated by changing transition metal elements and surface termination. Here, the uniqueness and superiority of MXenes as superexcellent supports for confining SACs are analyzed from structure and property. The synthetic strategy of MXene-supported SACs is also summarized, especially emphasizing the immobilization of isolated atom against aggregation by utilizing the formidable metal-support covalent coordination interaction. In addition, the applications of MXene-supported SACs in electrocatalytic field are highlighted, including hydrogen evolution reaction, oxygen evolution reaction, overall water splitting, oxygen reduction reaction, and nitrogen reduction reaction. Finally, the challenges and prospects are pointed out for the further understanding and practical application of MXene-supported SACs in electrocatalysis.

Hetero-MXenes: Theory, Synthesis, and Emerging Applications

Since their discovery in 2011, MXenes (abbreviation for transition metal carbides, nitrides, and carbonitrides) have emerged as a rising star in the family of 2D materials owing to their unique properties. Although the primary research interest is still focused on pristine MXenes and their composites, much attention has in recent years been paid also to MXenes with diverse compositions. To this end, this work offers a comprehensive overview of the progress on compositional engineering of MXenes in terms of doping and substituting from theoretical predictions to experimental investigations. Synthesis and properties are briefly introduced for pristine MXenes and then reviewed for hetero-MXenes. Theoretical calculations regarding the doping/substituting at M, X, and T sites in MXenes and the role of vacancies are summarized. After discussing the synthesis of hetero-MXenes with metal/nonmetal (N, S, P) elements by in situ and ex situ strategies, the focus turns to their emerging applications in various fields such as energy storage, electrocatalysts, and sensors. Finally, challenges and prospects of hetero-MXenes are addressed. It is anticipated that this review will be beneficial to bridge the gap between predictions and experiments as well as to guide the future design of hetero-MXenes with high performance.

Boosting photocatalytic hydrogen production from water by photothermally induced biphase systems

Solar-driven hydrogen production from water using particulate photocatalysts is considered the most economical and effective approach to produce hydrogen fuel with little environmental concern. However, the efficiency of hydrogen production from water in particulate photocatalysis systems is still low. Here, we propose an efficient biphase photocatalytic system composed of integrated photothermal-photocatalytic materials that use charred wood substrates to convert liquid water to water steam, simultaneously splitting hydrogen under light illumination without additional energy. The photothermal-photocatalytic system exhibits biphase interfaces of photothermally-generated steam/photocatalyst/hydrogen, which significantly reduce the interface barrier and drastically lower the transport resistance of the hydrogen gas by nearly two orders of magnitude. In this work, an impressive hydrogen production rate up to 220.74 μmol h^-1 cm^-2 in the particulate photocatalytic systems has been achieved based on the wood/CoO system, demonstrating that the photothermal-photocatalytic biphase system is cost-effective and greatly advantageous for practical applications.

In situ growth of TiO2 nanoparticles on nitrogen-doped Ti3C2 with isopropyl amine toward enhanced photocatalytic activity

Construction of heterojunction and nitrogen doping is an effective approach for synthesizing photocatalysts with high quantum yield and efficient electron-hole separation. 2D MXene Ti₃C₂ has been considered a good carbonaceous nanomaterial for designing heterojunction, while the original surface groups and stacked structure limit the electron-hole separation. Herein, a hybrid of nitrogen-doped Ti₃C₂ nanosheets and TiO₂ nanoparticles (NPs) composed of TiO₂ NPs in situ growing on isopropyl amine (iPA) modified Ti₃C₂ (iN-Ti₃C₂) was developed for the first time. The novel iN-Ti₃C₂/TiO₂ hybrid exhibited an excellent ultraviolet-light photodegradation of methylene blue (MB), with a degradation rate (0.02642 min^-1) significantly higher than that of pure TiO₂ NPs, bulk-Ti₃C₂/TiO₂, dimethyl sulfoxide modified Ti₃C₂/TiO₂ hybrid, and hydrazine monohydrate modified Ti₃C₂/TiO₂ hybrid. The formation of heterojunction between iN-Ti₃C₂ and TiO₂ and its role in the photocatalysis were systematically analyzed using various characterization techniques and density functional theory calculation. The iPA modification exfoliated Ti₃C₂ and doped N on Ti₃C₂ nanosheets; the in situ grown TiO₂ NPs formed efficient heterojunctions with the nanosheets; the N-doping facilitated electron migration in Ti₃C₂ and inhibited the recombination of photogenerated electron-hole pairs; •OH dominated the photodegradation of MB. This work provides a new approach of constructing efficient photocatalysts for the treatment of organics-polluted water.

Oxygen Vacancy Engineering in Titanium Dioxide for Sodium Storage

Titanium dioxide (TiO₂ ) is a promising anode material for sodium-ion batteries (SIBs) due to its low cost, natural abundance, nontoxicity, and excellent electrochemical stability. Oxygen vacancies, the most common point defects in TiO₂ , can dramatically influence the physical and chemical properties of TiO₂ , including band structure, crystal structure and adsorption properties. Recent studies have demonstrated that oxygen-deficient TiO₂ can significantly enhance sodium storage performance. Considering the importance of oxygen vacancies in modifying the properties of TiO₂ , the structural properties, common synthesis strategies, characterization techniques, as well as the contribution of oxygen-deficient TiO₂ on initial Coulombic efficiency, cyclic stability, rate performance for sodium storage are comprehensively described in this review. Finally, some perspectives on the challenge and future opportunities for the development of oxygen-deficient TiO₂ are proposed.

Abundant hydroxyl groups decorated on nitrogen vacancy-embedded g-C3N4 with efficient photocatalytic hydrogen evolution performance

Engineering hydroxyl and N vacancies on g-C₃N₄ led to dual mitigation of the recombination rate of photogenerated carriers, which was achieved by enriched hydroxyl groups trapping the holes and stable N vacancies capturing the electrons.

Ti3C2 2D MXene: Recent Progress and Perspectives in Photocatalysis

In 2011, with the successful isolation of Ti₃C₂, a door of 2D layered MXene has been opened and received growing attention from researchers. MXene refers to a family of two-dimensional (2D) materials made up of atomic layers of the transition metal, carbide, nitrides, or carbonitrides. Given the large surface area, adjustable surface terminal groups, and excellent conductivity of MXene, it has shown exciting potential in photocatalysis, energy conversion, and many other fields. Among many 2D MXene, Ti₃C₂ was the most studied for its availability, low cost, facile modification procedure, and outstanding electronic properties. In previous investigations, Ti₃C₂ has shown huge potential in the photocatalysis area. Ti₃C₂ in a photocatalysis system can enhance the separation of photoinduced electrons and holes, reduce charge recombination, and thus improve the photocatalysis performance in many systems. To adjust the performance of Ti₃C₂ in different applications, the properties of Ti₃C₂ including morphology, structures, and stability are tunable by different post-processing method in the hybridized materials. In this review, an all-around understanding of the fabrication and modification methods of Ti₃C₂ and their connection to photocatalytic applications of Ti₃C₂ MXene based materials are presented. Moreover, a summary and our perspectives of Ti₃C₂ are given for further investigation.

Interlayer Space Engineering of MXenes for Electrochemical Energy Storage Applications

The increasing demand for high-performance rechargeable energy storage systems has stimulated the exploration of advanced electrode materials. MXenes are a class of two-dimensional (2D) inorganic transition metal carbides/nitrides, which are promising candidates in electrodes. The layered structure facilitates ion insertion/extraction, which offers promising electrochemical characteristics for electrochemical energy storage. However, the low capacity accompanied by sluggish electrochemical kinetics of electrodes as well as interlayer restacking and collapse significantly impede their practical applications. Recently, interlayer space engineering of MXenes by different chemical strategies have been widely investigated in designing functional materials for various applications. In this review, an overview of the most recent progress of 2D MXenes engineering by intercalation, surface modification as well as heterostructures design is provided. Moreover, some critical challenges in future research on MXene-based electrodes have been also proposed.

Rational Design of Two-Dimensional Transition Metal Carbide/Nitride (MXene) Hybrids and Nanocomposites for Catalytic Energy Storage and Conversion

Electro-, photo-, and photoelectrocatalysis play a critical role toward the realization of a sustainable energy economy. They facilitate numerous redox reactions in energy storage and conversion systems, enabling the production of chemical feedstock and clean fuels from abundant resources like water, carbon dioxide, and nitrogen. One major obstacle for their large-scale implementation is the scarcity of cost-effective, durable, and efficient catalysts. A family of two-dimensional transition metal carbides, nitrides, and carbonitrides (MXenes) has recently emerged as promising earth-abundant candidates for large-area catalytic energy storage and conversion due to their unique properties of hydrophilicity, high metallic conductivity, and ease of production by solution processing. To take full advantage of these desirable properties, MXenes have been combined with other materials to form MXene hybrids with significantly enhanced catalytic performances beyond the sum of their individual components. MXene hybridization tunes the electronic structure toward optimal binding of redox active species to improve intrinsic activity while increasing the density and accessibility of active sites. This review outlines recent strategies in the design of MXene hybrids for industrially relevant electrocatalytic, photocatalytic, and photoelectrocatalytic applications such as water splitting, metal-air/sulfur batteries, carbon dioxide reduction, and nitrogen reduction. By clarifying the roles of individual material components in the MXene hybrids, we provide design strategies to synergistically couple MXenes with associated materials for highly efficient and durable catalytic applications. We conclude by highlighting key gaps in the current understanding of MXene hybrids to guide future MXene hybrid designs in catalytic energy storage and conversion applications.

Synthesis of Superior Visible-Light-Driven Nanophotocatalyst Using High Surface Area TiO2 Nanoparticles Decorated with CuxO Particles

This work provides an alternate unique simple methodology to design and synthesize chemically modified nanophotocatalyst based on high surface area TiO2 nanoparticles that can be used efficiently for the photodegradation of organic pollutants under normal visible light rather than complicated UV irradiation. In this study, dual visible light and UV-driven nanophotocatalysts were synthesized via wet chemistry procedures using high surface area TiO2 nanoparticles functionalized with (3-Aminopropyl) trimethoxysilane and attached chemically to the CuXO to improve the charge separation and maintain the non-charge recombination. The successful modification of the TiO2 nanoparticles and the formation of the TiO2-NH2-CuxO nanophotocatalyst were confirmed using different characterization techniques, and the results revealed the synthesis of high surface area TiO2 nanoparticles, and their chemical modification with an amino group and further decoration with copper to produce TiO2-NH2-CuxO nanophotocatalyst. The photocatalytic activity of TiO2 and TiO2-NH2-CuxO nanophotocatalyst were evaluated using methylene blue (MB) dye; as an example of organic pollutants. The resulting TiO2-NH2-CuxO nanophotocatalyst exhibited superior photocatalytic activity for the degradation of MB dye under visible light irradiation, due to the reduction in the energy bandgap. The degradation of the MB dye using the TiO2-NH2-CuxO nanophotocatalyst was investigated using LC-MS, and the results revealed that the hydroxyl free radical is mainly responsible for the cleavage and the degradation of the MB dye.

Bandgap engineering via boron and sulphur doped carbon modified anatase TiO2: a visible light stimulated photocatalyst for photo-fixation of N2 and TCH degradation

The present research reports the synthesis of two-dimensional (2D) sheet/flake-like nanostructures of crystalline carbon modified TiO₂ (CT), B-TiO₂ (B-CT), and S-TiO₂ (S-CT) using a facile one-pot synthesis method. The crystallinity and phase purity (anatase) of the prepared nano-photocatalyst were characterised using X-ray diffraction, selected area electron diffraction (SAED) and high-resolution transmission electron microscopy (HRTEM) analysis. Furthermore, the morphological details and elemental content of the sample were studied via scanning electron microscopy (SEM) and transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS), respectively. Additionally, the optoelectronic features of all of the prepared specimens were measured via UV-vis diffuse reflectance spectroscopy (DRS), photoluminescence (PL), impedance and Mott-Schottky studies. After successful characterisation, their photocatalytic performance was tested towards dinitrogen photo-fixation and tetracycline hydrochloride (TCH) degradation under visible light illumination. Moreover, the effective charge separation and greater availability of the active surface area led to the robust photocatalytic activity of the fabricated B-CT compared to the CT and S-CT samples, which correlates well with the PL, impedance and surface area analysis. B-CT displays the highest photocatalytic activity, i.e. 32.38 μmol L^-1 (conversion efficiency = 0.076%) of ammonia production, and 95% tetracycline hydrochloride (10 ppm) degradation. Here, we have effectively designed a novel and productive pathway towards the enhancement of the photocatalytic performance of visible photon active TiO₂-based materials for energy and environmental sustainability.

CVD growth of large-area InS atomic layers and device applications

Group-III monochalcogenides of two-dimensional (2D) layered materials have attracted widespread attention among scientists due to their unique electronic performance and interesting chemical and physical properties. Indium sulfide (InS) is attracting increasing interest from scientists because it has two distinct crystal structures. However, studies on the synthesis of highly crystalline, large-area, and atomically thin-film InS have not been reported thus far. Here, the chemical vapor deposition (CVD) synthesis method of atomic InS crystals has been reported in this paper. The direct chemical vapour phase reaction of metal oxides with chalcogen precursors produces a large-sized hexagonal crystal structure and atomic-thickness InS flakes or films. The InS atomic films are merged with a plurality of triangular InS crystals that are uniform and entire and have surface areas of 1 cm2 and controllable thicknesses in bilayers or trilayers. The properties of the as-grown highly crystalline samples were characterized by spectroscopic and microscopic measurements. The ion-gel gated InS field-effect transistors (FETs) reveal n-type transport behavior, and have an on-off current ratio of >103 and a room-temperature electron mobility of ∼2 cm2 V-1 s-1. Moreover, our CVD InS can be transferred from mica to any substrates, so various 2D materials can be reassembled into vertically stacked heterostructures, thus facilitating the development of heterojunctions and exploration of the properties and applications of their interactions.