Synthetic Saccharomyces cerevisiae ‐ Shewanella oneidensis consortium enables glucose‐fed high‐performance microbial fuel cell

Enhanced bioenergy production through dual-chamber microbial fuel cells: Utilizing citric acid factory wastewater and grape waste as substrates

INTRODUCTION

Microbial fuel cell (MFC) is a variant of the bio-electro-chemical system that uses microorganisms as biocatalysts to generate bioenergy by oxidizing organic matter. Due to its two-prong feature of simultaneously treating wastewater and generating electricity, it has drawn extensive interest by scientific communities around the world. However, the pollution purifying capacity and power production of MFC at the laboratory scale have tended to remain steady, and there have been no reports of a performance breakthrough.

PROBLEM STATEMENT

This research was conducted to produce electricity and evaluate the efficiency of chemical oxygen demand (COD) removal from wastewater containing Citric Acid using a two-chamber microbial fuel cell without an intermediary.

METHODOLOGY

In this research, citric acid factory wastewater was used as the substrate, graphite as the electrode, Nafion membrane for proton transfer from anode to cathode, and grape waste as a carbon source. These Experiments were performed at room temperature and neutral pH. Also, the effect of three independent variables mixed liquor suspended solid (MLSS), Carbon: Nitrogen: Phosphorus stoichiometric ratio (COD:TKN:P), and grape waste on electricity production and wastewater treatment was investigated. Then, the optimal values of each variable were determined under favorable conditions for electricity generation and COD reduction.

RESULTS

The MFC was conducted at the optimal values of MLSS 1400 mg/L, the stoichiometric ratio of COD:TKN:P 140:10:1, and the grape waste dose of 1.4 g/L. At these conditions, the obtained maximum power density and current density were 18228.10 µW/m2 and 244.44 mA/m2, respectively. The maximum COD removal was 72% achieved in the values of MLSS 1400 mg/L, the stoichiometric ratio of COD:TKN:P equal to 260:10:1, and 1.4 g/L of grape waste. The maximum open circuit voltage was also recorded as 678 mV, obtained at MLSS 3000 mg/L, the stoichiometric ratio of COD:TKN:P equal to 200:10:1, and for a grape waste dose of 2 g/L.

CONCLUSION

The results of this research showed that the use of grape waste to supply glucose to microorganisms in the MFC system has a significant effect on increasing energy production and COD removal, and it is recommended to conduct additional research in the future to improve the efficiency. However, scalability and practical application potential of these integrated technologies are the challenges towards their real-world applications in small scale trials.

Engineering extracellular electron transfer pathways of electroactive microorganisms by synthetic biology for energy and chemicals production

The excessive consumption of fossil fuels causes massive emission of CO2, leading to climate deterioration and environmental pollution. The development of substitutes and sustainable energy sources to replace fossil fuels has become a worldwide priority. Bio-electrochemical systems (BESs), employing redox reactions of electroactive microorganisms (EAMs) on electrodes to achieve a meritorious combination of biocatalysis and electrocatalysis, provide a green and sustainable alternative approach for bioremediation, CO2 fixation, and energy and chemicals production. EAMs, including exoelectrogens and electrotrophs, perform extracellular electron transfer (EET) (i.e., outward and inward EET), respectively, to exchange energy with the environment, whose rate determines the efficiency and performance of BESs. Therefore, we review the synthetic biology strategies developed in the last decade for engineering EAMs to enhance the EET rate in cell-electrode interfaces for facilitating the production of electricity energy and value-added chemicals, which include (1) progress in genetic manipulation and editing tools to achieve the efficient regulation of gene expression, knockout, and knockdown of EAMs; (2) synthetic biological engineering strategies to enhance the outward EET of exoelectrogens to anodes for electricity power production and anodic electro-fermentation (AEF) for chemicals production, including (i) broadening and strengthening substrate utilization, (ii) increasing the intracellular releasable reducing equivalents, (iii) optimizing c-type cytochrome (c-Cyts) expression and maturation, (iv) enhancing conductive nanowire biosynthesis and modification, (v) promoting electron shuttle biosynthesis, secretion, and immobilization, (vi) engineering global regulators to promote EET rate, (vii) facilitating biofilm formation, and (viii) constructing cell-material hybrids; (3) the mechanisms of inward EET, CO2 fixation pathway, and engineering strategies for improving the inward EET of electrotrophic cells for CO2 reduction and chemical production, including (i) programming metabolic pathways of electrotrophs, (ii) rewiring bioelectrical circuits for enhancing inward EET, and (iii) constructing microbial (photo)electrosynthesis by cell-material hybridization; (4) perspectives on future challenges and opportunities for engineering EET to develop highly efficient BESs for sustainable energy and chemical production. We expect that this review will provide a theoretical basis for the future development of BESs in energy harvesting, CO2 fixation, and chemical synthesis.

Harnessing fungal bio-electricity: a promising path to a cleaner environment

Integrating fungi into fuel cell systems presents a promising opportunity to address environmental pollution while simultaneously generating energy. This review explores the innovative concept of constructing wetlands as fuel cells for pollutant degradation, offering a practical and eco-friendly solution to pollution challenges. Fungi possess unique capabilities in producing power, fuel, and electricity through metabolic processes, drawing significant interest for applications in remediation and degradation. Limited data exist on fungi's ability to generate electricity during catalytic reactions involving various enzymes, especially while remediating pollutants. Certain species, such as Trametes versicolor, Ganoderma lucidum, Galactomyces reessii, Aspergillus spp., Kluyveromyce smarxianus, and Hansenula anomala, have been reported to generate electricity at 1200 mW/m3, 207 mW/m2, 1,163 mW/m3, 438 mW/m3, 850,000 mW/m3, and 2,900 mW/m3, respectively. Despite the eco-friendly potential compared to conventional methods, fungi's role remains largely unexplored. This review delves into fungi's exceptional potential as fuel cell catalysts, serving as anodic or cathodic agents to mitigate land, air, and water pollutants while simultaneously producing fuel and power. Applications cover a wide range of tasks, and the innovative concept of wetlands designed as fuel cells for pollutant degradation is discussed. Cost-effectiveness may vary depending on specific contexts and applications. Fungal fuel cells (FFCs) offer a versatile and innovative solution to global challenges, addressing the increasing demand for alternative bioenergy production amid population growth and expanding industrial activities. The mechanistic approach of fungal enzymes via microbial combinations and electrochemical fungal systems facilitates the oxidation of organic substrates, oxygen reduction, and ion exchange membrane orchestration of essential reactions. Fungal laccase plays a crucial role in pollutant removal and monitoring environmental contaminants. Fungal consortiums show remarkable potential in fine-tuning FFC performance, impacting both power generation and pollutant degradation. Beyond energy generation, fungal cells effectively remove pollutants. Overall, FFCs present a promising avenue to address energy needs and mitigate pollutants simultaneously.

Sustainable circular biorefinery approach for novel building blocks and bioenergy production from algae using microbial fuel cell

The imminent need for transition to a circular biorefinery using microbial fuel cells (MFC), based on the valorization of renewable resources, will ameliorate the carbon footprint induced by industrialization. MFC catalyzed by bioelectrochemical process drew significant attention initially for its exceptional potential for integrated production of biochemicals and bioenergy. Nonetheless, the associated costly bioproduct production and slow microbial kinetics have constrained its commercialization. This review encompasses the potential and development of macroalgal biomass as a substrate in the MFC system for L-lactic acid (L-LA) and bioelectricity generation. Besides, an insight into the state-of-the-art technological advancement in the MFC system is also deliberated in detail. Investigations in recent years have shown that MFC developed with different anolyte enhances power density from several µW/m2 up to 8160 mW/m2. Further, this review provides a plausible picture of macroalgal-based L-LA and bioelectricity circular biorefinery in the MFC system for future research directions.

Microbial applications for sustainable space exploration beyond low Earth orbit

With the construction of the International Space Station, humans have been continuously living and working in space for 22 years. Microbial studies in space and other extreme environments on Earth have shown the ability for bacteria and fungi to adapt and change compared to "normal" conditions. Some of these changes, like biofilm formation, can impact astronaut health and spacecraft integrity in a negative way, while others, such as a propensity for plastic degradation, can promote self-sufficiency and sustainability in space. With the next era of space exploration upon us, which will see crewed missions to the Moon and Mars in the next 10 years, incorporating microbiology research into planning, decision-making, and mission design will be paramount to ensuring success of these long-duration missions. These can include astronaut microbiome studies to protect against infections, immune system dysfunction and bone deterioration, or biological in situ resource utilization (bISRU) studies that incorporate microbes to act as radiation shields, create electricity and establish robust plant habitats for fresh food and recycling of waste. In this review, information will be presented on the beneficial use of microbes in bioregenerative life support systems, their applicability to bISRU, and their capability to be genetically engineered for biotechnological space applications. In addition, we discuss the negative effect microbes and microbial communities may have on long-duration space travel and provide mitigation strategies to reduce their impact. Utilizing the benefits of microbes, while understanding their limitations, will help us explore deeper into space and develop sustainable human habitats on the Moon, Mars and beyond.

Interactions among microorganisms functionally active for electron transfer and pollutant degradation in natural environments

Compared to single microbial strains, complex interactions between microbial consortia composed of various microorganisms have been shown to be effective in expanding ecological functions and accomplishing biological processes. Electroactive microorganisms (EMs) and degradable microorganisms (DMs) play vital roles in bioenergy production and the degradation of organic pollutants hazardous to human health. These microorganisms can strongly interact with other microorganisms and promote metabolic cooperation, thus facilitating electricity production and pollutant degradation. In this review, we describe several specific types of EMs and DMs based on their ability to adapt to different environments, and summarize the mechanism of EMs in extracellular electron transfer. The effects of interactions between EMs and DMs are evaluated in terms of electricity production and degradation efficiency. The principle of the enhancement in microbial consortia is also introduced, such as improved biomass, changed degradation pathways, and biocatalytic potentials, which are directly or indirectly conducive to human health.

A common inducer molecule enhances sugar utilization by Shewanella oneidensis MR-1

Shewanella oneidensis MR-1 is an electroactive bacterium that is a promising host for bioelectrochemical technologies, which makes it a common target for genetic engineering, including gene deletions and expression of heterologous pathways. Expression of heterologous genes and gene knockdown via CRISPRi in S. oneidensis are both frequently induced by β-D-1-thiogalactopyranoside (IPTG), a commonly used inducer molecule across many model organisms. Here, we report and characterize an unexpected phenotype; IPTG enhances the growth of wild-type S. oneidensis MR-1 on the sugar substrate N-acetylglucosamine (NAG). IPTG improves the carrying capacity of S. oneidensis growing on NAG while the growth rate remains similar to cultures without the inducer. Extracellular acetate accumulates faster and to a higher concentration in cultures without IPTG than those with it. IPTG appears to improve acetate metabolism, which combats the negative effect that acetate accumulation has on the growth of S. oneidensis with NAG. We recommend using extensive experimental controls and careful data interpretation when using both NAG and IPTG in S. oneidensis cultures.

Improved energy efficiency in microbial fuel cells by bioethanol and electricity co-generation

Background

Microbial electricity production has received considerable attention from researchers due to its environmental friendliness and low price. The increase in the number of intracellular electrons in a microbial fuel cell (MFC) helps to improve the MFC performance.

Results

In this study, we accumulated excess electrons intracellularly by knocking out the gene related to intracellular electron consumption in Saccharomyces cerevisiae, and the elevated intracellular electron pool positively influenced the performances of MFCs in terms of electricity production, while helping to increase ethanol production and achieve ethanol and electricity co-production, which in turn improved the utilization of substrates. The final knockout strain reached a maximum ethanol yield of 7.71 g/L and a maximum power density of 240 mW/m2 in the MFC, which was 12 times higher than that of the control bacteria, with a 17.3% increase in energy utilization.

Conclusions

The knockdown of intracellular electron-consuming genes reported here allowed the accumulation of excess electrons in cells, and the elevated intracellular electron pool positively influenced the electrical production performance of the MFC. Furthermore, by knocking out the intracellular metabolic pathway, the yield of ethanol could be increased, and co-production of ethanol and electricity could be achieved. Thus, the MFC improved the utilization of the substrate.

Double Bacteria Synergistic Catalytic Reduction System for Heavy Metal Detoxification Treatment

Synthetic biology has promoted the development of microbial therapy, but the scope of applicable microbial species is limited and transgenic microorganisms also display safety risks for in vivo applications. Interestingly, symbiotic microorganisms in nature can achieve functional updates by metabolic cooperation. Here, we report on a nongenetic method for engineering microorganisms to construct a heavy metal ion reduction system, which was prepared by linking Shewanella oneidensis MR-1 (SO) and Lactobacillus rhamnosus GG (LGG). SO could reduce metal ions but is limited by finite substrates in vivo. LGG could metabolize glucose to lactate as a substrate for SO, promoting extracellular electron transfer by SO and heavy metal ion reduction. Meanwhile, SO could generate electron donor cytochrome C to promote metabolism of LGG, forming metabolic synergy and circulation between these two bacteria. The SO-LGG system shows splendid ability to remove heavy metal ions and inflammatory modulation in acute or chronic heavy metal poisoning.

3D Conducting Polymeric Membrane and Scaffold Saccharomyces cerevisiae Biofilms to Enhance Energy Conversion in Microbial Fuel Cells

Microbial fuel cells (MFCs) can spontaneously convert chemical energy into electricity using biocatalytic microorganisms and organic matter as fuel feedstocks. Three-dimensional cross-linked poly(vinyl alcohol)-based membranes were produced by a sol-gel method under homogeneous catalysis and used as the electrolyte to facilitate effective proton conduction. Under dry conditions, these polymeric membranes showed high water uptake (120%) and ionic conductivity (2.815 mS cm^-1). In the anode compartment, the scaffold Saccharomyces cerevisiae film biocatalysts were used to improve electron transfer to the cathode, using three major configurations to generate a higher power output. It was found that the graphene anchoring, red light (RL) stimulation, and methylene blue (MB) mediation-enhanced device performance. The electrochemically derived graphene improved the power and current density by 40% because of its high conductivity. The RL stimulation increased the power density by 80% because of a shortened electron flow path to complex III. The MB mediation also yielded a higher current density by 340% because MB can bypass the electron flow from complex II to cytochrome c and transfer electrons directly to complex III. The individual and collective increase in power output was due to more efficient electron flow from the electronic network permeating the biofilm. The generated electrons were transferred either to graphene as an energy-efficient direct transfer mode or to methylene blue as a long-range redox mediator for indirect transfer. Red light stimulation enhanced oxygen utilization efficiency and stimulated electrons in redox proteins enhancing electron flux. These processes generated higher power through the more efficient generation of electrons and faster transport to the external circuit. As society migrates from gasoline consumption to low carbon-based fuels, the MFCs become important in producing electrical energy with low net emissions.

Integration of various technology-based approaches for enhancing the performance of microbial fuel cell technology: A review

The conflict between climate change and growing global energy demand is an immense sustainability challenge that requires noteworthy scientific and technological developments. Recently the importance of microbial fuel cell (MFC) on this issue has seen profound investigation due to its inherent ability of simultaneous wastewater treatment, and power production. However, the challenges of economy-related manufacturing and operation costs should be lowered to achieve positive field-scale demonstration. Also, a variety of different field deployments will lead to improvisation. Hence, this review article discusses the possibility of integration of MFC technology with various technologies of recent times leading to advanced sustainable MFC technology. Technological innovation in the field of nanotechnology, genetic engineering, additive manufacturing, artificial intelligence, adaptive control, and few other hybrid systems integrated with MFCs is discussed. This comprehensive and state-of-the-art study elaborates hybrid MFCs integrated with various technology and its working principles, modified electrode material, complex and easy to manufacture reactor designs, and the effects of various operating parameters on system performances. Although integrated systems are promising, much future research work is needed to overcome the challenges and commercialize hybrid MFC technology.

Efficiency of microbial fuel cells in the treatment and energy recovery from food wastes: Trends and applications - A review

The rising global population and their food habits result in food wastage and cause an obstacle in its treatment and disposal. Due to the rapid shift in the lifestyle of the human population and urbanization, almost one-third of the food produced is wasted from various sectors like domestic sources, agricultural sectors, and industrial sectors. These food resources squandered are rich in organic biomolecules which can cause complications upon direct disposal in the environment. Conventional disposal methods like composting, landfills and incineration demand high costs besides causing severe environmental and health issues. To overcome these demerits of the conventional methods and to avoid the loss of rich organic food resources, there is an immediate need for a sustainable and eco-friendly solution for the valorization of the food wastes. Microbial fuel cells (MFCs) are gaining attention, due to their ideal approach in the production of electricity and parallel treatment of organic food wastes. The MFCs are significant as an innovative approach using microorganisms and oxidizing the organic food wastes into bio-electricity. In this review, the recent advancements and practices of the MFCs in the field of food waste treatment and management along with electricity production are discussed. The major outcome of this work highlights the setting up of MFC for the treatment of higher volumes of food waste residues and enhancing the bioelectricity production in an optimal condition. For further improvements in the food waste treatments using MFCs, greater understanding and more research needs are to be focused on the commercialization, different operational modes, operational types, and low-cost fabrication coupled with careful examination of scale-up factors.

Recent trends in upgrading the performance of yeast as electrode biocatalyst in microbial fuel cells

Microbial fuel cell (MFC) is an optimistic fuel cell technology that applies microorganism's biochemical catalytic activities in consuming organic substrate and produce electricity. In the past, several researchers have reported power generation from Saccharomyces cerevisiae, but nowadays, most of the studies are centred around bacterial biofilms (prokaryotes) as anode biocatalyst. Yeast (a eukaryote) has also been applied as a biocatalyst in MFCs as they are non-pathogenic, easy to handle and tolerant to various environmental conditions. Yeast strains such as Arxula adeninvorans, Candida melibiosica, Hansenula polymorpha, Hansenula anomala, Kluyveromyces marxianus and Saccharomyces cerevisiae have been utilized in MFCs. This review summarizes the application of yeast as an anode biocatalyst together with a discussion on the mechanism of electron transfer from yeast cells to the anode and highlights the techniques applied in improving the efficiency of yeast-based MFCs. The recent challenges and benefits of utilizing yeast in MFCs have been also encapsulated in this review.

Bioenergy from dairy manure: technologies, challenges and opportunities

Dairy manure (DM) is a kind of cheap cellulosic biomass resource which includes lignocellulose and mineral nutrients. Random stacks not only leads damage to the environment, but also results in waste of natural resources. The traditional ways to use DM include returning it to the soil or acting as a fertilizer, which could reduce environmental pollution to some extent. However, the resource utilization rate is not high and socio-economic performance is not utilized. To expand the application of DM, more and more attention has been paid to explore its potential as bioenergy or bio-chemicals production. This article presented a comprehensive review of different types of bioenergy production from DM and provided a general overview for bioenergy production. Importantly, this paper discussed potentials of DM as candidate feedstocks not only for biogas, bioethanol, biohydrogen, microbial fuel cell, lactic acid, and fumaric acid production by microbial technology, but also for bio-oil and biochar production through apyrolysis process. Additionally, the use of manure for replacing freshwater or nutrients for algae cultivation and cellulase production were also discussed. Overall, DM could be a novel suitable material for future biorefinery. Importantly, considerable efforts and further extensive research on overcoming technical bottlenecks like pretreatment, the effective release of fermentable sugars, the absence of robust organisms for fermentation, energy balance, and life cycle assessment should be needed to develop a comprehensive biorefinery model.

Engineering S. oneidensis for Performance Improvement of Microbial Fuel Cell-a Mini Review

Microbial fuel cell (MFC) is a promising technology that utilizes exoelectrogens cultivated in the form of biofilm to generate power from various types of sources supplied. A metal-reducing pathway is utilized by these organisms to transfer electrons obtained from the metabolism of substrate from anaerobic respiration extracellularly. A widely established model organism that is capable of extracellular electron transfer (EET) is Shewanella oneidensis. This review highlights the strategies used in the transformation of S. oneidensis and the recent development of MFC in terms of intervention through genetic modifications. S. oneidensis was genetically engineered for several aims including the study on the underlying mechanisms of EET, and the enhancement of power generation and wastewater treating potential when used in an MFC. Through engineering S. oneidensis, genes responsible for EET are identified and strategies on enhancing the EET efficiency are studied. Overexpressing genes related to EET to enhance biofilm formation, mediator biosynthesis, and respiration appears as one of the common approaches.

Potential of Zymomonas mobilis as an electricity producer in ethanol production

BACKGROUND

Microbial fuel cell (MFC) convokes microorganism to convert biomass into electricity. However, most well-known electrogenic strains cannot directly use glucose to produce valuable products. Zymomonas mobilis, a promising bacterium for ethanol production, owns special Entner-Doudoroff pathway with less ATP and biomass produced and the low-energy coupling respiration, making Z. mobilis a potential exoelectrogen.

RESULTS

A glucose-consuming MFC is constructed by inoculating Z. mobilis. The electricity with power density 2.0 mW/m² is derived from the difference of oxidation-reduction potential (ORP) between anode and cathode chambers. Besides, two-type electricity generation is observed as glucose-independent process and glucose-dependent process. For the sake of enhancing MFC efficiency, extracellular and intracellular strategies are implemented. Biofilm removal and addition of c-type cytochrome benefit electricity performance and Tween 80 accelerates the electricity generation. Perturbation of cellular redox balance compromises the electricity output, indicating that redox homeostasis is the principal requirement to reach ideal voltage.

CONCLUSION

This study identifies potential feature of electricity activity for Z. mobilis and provides multiple strategies to enhance the electricity output. Therefore, additional electricity generation will benefit the techno-economic viability of the commercial bulk production for biochemicals or biofuels in an efficient and environmentally sustainable manner.

Microbial consortia including methanotrophs: some benefits of living together

With the progress of biotechnological research and improvements made in bioprocessing with pure cultures, microbial consortia have gained recognition for accomplishing biological processes with improved effectiveness. Microbes are indispensable tool in developing bioprocesses for the production of bioenergy and biochemicals while utilizing renewable resources due to technical, economic and environmental advantages. They communicate with specific cohorts in close proximity to promote metabolic cooperation. Use of positive microbial associations has been recognized widely, especially in food industries and bioremediation of toxic compounds and waste materials. Role of microbial associations in developing sustainable energy sources and substitutes for conventional fuels is highly promising with many commercial prospects. Detoxification of chemical contaminants sourced from domestic, agricultural and industrial wastes has also been achieved through microbial catalysis in pure and co-culture systems. Methanotrophs, the sole biological sink of greenhouse gas methane, catalyze the methane monooxygenasemediated oxidation of methane to methanol, a high energy density liquid and key platform chemical to produce commodity chemical compounds and their derivatives. Constructed microbial consortia have positive effects, such as improved biomass, biocatalytic potential, stability etc. In a methanotroph-heterotroph consortium, non-methanotrophs provide key nutrient factors and alleviate the toxicity from the culture. Non-methanotrophic organisms biologically stimulate the growth and activity of methanotrophs via production of growth stimulators. However, methanotrophs in association with co-cultured microorganisms are in need of further exploration and thorough investigation to study their interaction mode and application with improved effectiveness.

Engineering Microbial Consortia for High-Performance Cellulosic Hydrolyzates-Fed Microbial Fuel Cells

Microbial fuel cells (MFCs) are eco-friendly bio-electrochemical reactors that use exoelectrogens as biocatalyst for electricity harvest from organic biomass, which could also be used as biosensors for long-term environmental monitoring. Glucose and xylose, as the primary ingredients from cellulose hydrolyzates, is an appealing substrate for MFC. Nevertheless, neither xylose nor glucose can be utilized as carbon source by well-studied exoelectrogens such as Shewanella oneidensis. In this study, to harvest the electricity by rapidly harnessing xylose and glucose from corn stalk hydrolysate, we herein firstly designed glucose and xylose co-fed engineered Klebsiella pneumoniae-S. oneidensis microbial consortium, in which K. pneumoniae as the fermenter converted glucose and xylose into lactate to feed the exoelectrogens (S. oneidensis). To produce more lactate in K. pneumoniae, we eliminated the ethanol and acetate pathway via deleting pta (phosphotransacetylase gene) and adhE (alcohol dehydrogenase gene) and further constructed a synthesis and delivery system through expressing ldhD (lactate dehydrogenase gene) and lldP (lactate transporter gene). To facilitate extracellular electron transfer (EET) of S. oneidensis, a biosynthetic flavins pathway from Bacillus subtilis was expressed in a highly hydrophobic S. oneidensis CP-S1, which not only improved direct-contacted EET via enhancing S. oneidensis adhesion to the carbon electrode but also accelerated the flavins-mediated EET via increasing flavins synthesis. Furthermore, we optimized the ratio of glucose and xylose concentration to provide a stable carbon source supply in MFCs for higher power density. The glucose and xylose co-fed MFC inoculated with the recombinant consortium generated a maximum power density of 104.7 ± 10.0 mW/m², which was 7.2-folds higher than that of the wild-type consortium (12.7 ± 8.0 mW/m²). Lastly, we used this synthetic microbial consortium in the corn straw hydrolyzates-fed MFC, obtaining a power density 23.5 ± 6.0 mW/m².

Electricigens in the anode of microbial fuel cells: pure cultures versus mixed communities

Microbial fuel cell (MFC) is an environmentally friendly technology for electricity harvesting from a variety of substrates. Microorganisms used as catalysts in the anodic chamber, which are termed as electricigens, play a major role in the operation of MFCs. This review provides an introduction to the currently identified electricigens on their taxonomical groups and electricity producing abilities. The mechanism of electron transfer from electricigens to electrode is highlighted. The performances of pure culture and mixed communities are compared particularly. It has been proved that the electricity generation capacity and the ability to adapt to the complex environment of MFC systems constructed by pure microbial cultures are less than the systems constructed by miscellaneous consortia. However, pure cultures are useful to clarify the electron transfer mechanism at the microbiological level and further reduce the complexity of mixed communities. Future research trends of electricigens in MFCs should be focused on screening, domestication, modification and optimization of multi-strains to improve their electrochemical activities. Although the MFC techniques have been greatly advanced during the past few years, the present state of this technology still requires to be combined with other processes for cost reduction.

Integrated proteomic and metabolomic analysis of a reconstructed three-species microbial consortium for one-step fermentation of 2-keto-l-gulonic acid, the precursor of vitamin C

Microbial consortia, with the merits of strong stability, robustness, and multi-function, played critical roles in human health, bioenergy, and food manufacture, etc. On the basis of ‘build a consortium to understand it’, a novel microbial consortium consisted of Gluconobacter oxydans, Ketogulonicigenium vulgare and Bacillus endophyticus was reconstructed to produce 2-keto-l-gulonic acid (2-KGA), the precursor of vitamin C. With this synthetic consortium, 73.7 g/L 2-KGA was obtained within 30 h, which is comparable to the conventional industrial method. A combined time-series proteomic and metabolomic analysis of the fermentation process was conducted to further investigate the cell–cell interaction. The results suggested that the existence of B. endophyticus and G. oxydans together promoted the growth of K. vulgare by supplying additional nutrients, and promoted the 2-KGA production by supplying more substrate. Meanwhile, the growth of B. endophyticus and G. oxydans was compromised from the competition of the nutrients by K. vulgare, enabling the efficient production of 2-KGA. This study provides valuable guidance for further study of synthetic microbial consortia.

Fungi-Based Microbial Fuel Cells

Fungi are among the microorganisms able to generate electricity as a result of their metabolic processes. Throughout the last several years, a large number of papers on various microorganisms for current production in microbial fuel cells (MFCs) have been published; however, fungi still lack sufficient evaluation in this regard. In this review, we focus on fungi, paying special attention to their potential applicability to MFCs. Fungi used as anodic or cathodic catalysts, in different reactor configurations, with or without the addition of an exogenous mediator, are described. Contrary to bacteria, in which the mechanism of electron transfer is pretty well known, the mechanism of electron transfer in fungi-based MFCs has not been studied intensively. Thus, here we describe the main findings, which can be used as the starting point for future investigations. We show that fungi have the potential to act as electrogens or cathode catalysts, but MFCs based on bacteria–fungus interactions are especially interesting. The review presents the current state-of-the-art in the field of MFC systems exploiting fungi.

Interkingdom microbial consortia mechanisms to guide biotechnological applications

Microbial consortia are capable of surviving diverse conditions through the formation of synergistic population-level structures, such as stromatolites, microbial mats and biofilms. Biotechnological applications are poised to capitalize on these unique interactions. However, current artificial co-cultures constructed for societal benefits, including biosynthesis, agriculture and bioremediation, face many challenges to perform as well as natural consortia. Interkingdom microbial consortia tend to be more robust and have higher productivity compared with monocultures and intrakingdom consortia, but the control and design of these diverse artificial consortia have received limited attention. Further, feasible research techniques and instrumentation for comprehensive mechanistic insights have only recently been established for interkingdom microbial communities. Here, we review these recent advances in technology and our current understanding of microbial interaction mechanisms involved in sustaining or developing interkingdom consortia for biotechnological applications. Some of the interactions among members from different kingdoms follow similar mechanisms observed for intrakingdom microbial consortia. However, unique interactions in interkingdom consortia, including endosymbiosis or interkingdom-specific cell-cell interactions, provide improved mitigation to external stresses and inhibitory compounds. Furthermore, antagonistic interactions among interkingdom species can promote fitness, diversification and adaptation, along with the production of beneficial metabolites and enzymes for society. Lastly, we shed light on future research directions to develop study methods at the level of metabolites, genes and meta-omics. These potential research methods could lead to the control and utilization of highly diverse microbial communities.

Efficient Biomass Fuel Cell Powered by Sugar with Photo- and Thermal-Catalysis by Solar Irradiation

The utilization of biomass sugars has received great interesting recently. Herein, we present a highly efficient hybrid solar biomass fuel cell that utilizes thermal- and photocatalysis of solar irradiation and converts biomass sugars into electricity with high power output. The fuel cell uses polyoxometalates (POMs) as photocatalyst to decompose sugars and capture their electrons. The reduced POMs have strong visible and near-infrared light adsorption, which can significantly increase the temperature of the reaction system and largely promotes the thermal oxidation of sugars by the POM. In addition, the reduced POM functions as charge carrier that can release electrons at the anode in the fuel cell to generate electricity. The electron-transfer rates from glucose to POM under thermal and light-irradiation conditions were investigated in detail. The power outputs of this solar biomass fuel cell are investigated by using different types of sugars as fuels, with the highest power density reaching 45 mW cm^-2 .

Synthetic Klebsiella pneumoniae-Shewanella oneidensis Consortium Enables Glycerol-Fed High-Performance Microbial Fuel Cells

Microbial fuel cell (MFC) is an eco-friendly bio-electrochemical sys-tem that uses microorganism as biocatalyst to convert biomass into electricity. Glycerol, as a waste in the biodiesel refinery processes, is an appealing substrate for MFC. Nevertheless, glycerol cannot be utilized as carbon source by well-known exoelectrogens such as Shewanella oneidensis. Herein, to generate electricity by rapidly harnessing glycerol, the authors rationally constructed a Klebsiella pneumoniae-Shewanella oneidensis microbial consortium to efficiently harvest electricity from glyc-erol, in which K. pneumoniae converted glycerol into lactate, fed to S. oneidensis as carbon source and electron donor. To improve electricity output, the authors systematically engineered the consortium in terms of carbon flux distribution and efficiency of extracellular electron transfer (EET). To direct more carbon flux to lactate biosynthesis in K. pneumoniae, the authors eliminated the ethanol pathway by knocking out the alcohol dehydrogenase gene (adhE), and enhanced lactate biosynthesis by heterologously expressing a lactate dehydrogen-ase gene (ldhD) from Lactobacillus bulgaricus and a lactate transporter gene (lldP) from Escherichia coli. To facilitate EET between S. oneidensis and anode surfaces, a biosynthetic flavins pathway from Bacillus subtilis is introduced into S. oneidensis. The author further optimized the glycerol concentration, thus S. oneidensis could be continuously fed with lactate synthesized from K. pneumoniae at a constant rate. Our glycerol-fed MFC generated a maximum power density of 19.9 mW/m² , significantly higher than that of the wild-type consor-tium. This work suggested that engineering microbial consortia is an effi-cient strategy to expand the spectrum of usable carbon sources and promote electricity power production in MFCs.

Engineering Shewanella oneidensis enables xylose-fed microbial fuel cell

BACKGROUND

The microbial fuel cell (MFC) is a green and sustainable technology for electricity energy harvest from biomass, in which exoelectrogens use metabolism and extracellular electron transfer pathways for the conversion of chemical energy into electricity. However, Shewanella oneidensis MR-1, one of the most well-known exoelectrogens, could not use xylose (a key pentose derived from hydrolysis of lignocellulosic biomass) for cell growth and power generation, which limited greatly its practical applications.

RESULTS

Herein, to enable S. oneidensis to directly utilize xylose as the sole carbon source for bioelectricity production in MFCs, we used synthetic biology strategies to successfully construct four genetically engineered S. oneidensis (namely XE, GE, XS, and GS) by assembling one of the xylose transporters (from Candida intermedia and Clostridium acetobutylicum) with one of intracellular xylose metabolic pathways (the isomerase pathway from Escherichia coli and the oxidoreductase pathway from Scheffersomyces stipites), respectively. We found that among these engineered S. oneidensis strains, the strain GS (i.e. harbouring Gxf1 gene encoding the xylose facilitator from C. intermedi, and XYL1, XYL2, and XKS1 genes encoding the xylose oxidoreductase pathway from S. stipites) was able to generate the highest power density, enabling a maximum electricity power density of 2.1 ± 0.1 mW/m².

CONCLUSION

To the best of our knowledge, this was the first report on the rationally designed Shewanella that could use xylose as the sole carbon source and electron donor to produce electricity. The synthetic biology strategies developed in this study could be further extended to rationally engineer other exoelectrogens for lignocellulosic biomass utilization to generate electricity power.