Covalent Surface Modification of Oxide Surfaces

Chemical bonding of cross-linked glutaraldehyde/chitosan on the surface of a titanium wire to prepare a robust biocompatible SPME fiber for analysis of phytohormones in plants

A robust biocompatible solid-phase microextraction (SPME) fiber, so-called Ti/APTS/GA/CS, was prepared by chemical bonding of cross-linked glutaraldehyde-chitosan to the surface of a titanium wire using APTS. The fiber was applied for sampling of phytohormones in plant tissues, followed by HPLC-UV analysis. The structure and morphology of the fiber coating was investigated by FT-IR, SEM, EDX, XRD, and TGA techniques. A Box-Behnken design was implemented to optimize the experimental variables. The calibration graphs were linear over a wide linear range (0.5-200 μg L-1) with LODs over the range of 0.01-0.06 μg L-1. The intra-day and inter-day precisions were found to be 1.3-6.3% and 4.3-7.3%, respectively. The matrix effect values ranged from 86.5% to 111.7%, indicating that the complex sample matrices had an insignificant effect on the determination of phytohormones. The fiber was successfully employed for the direct-immersion SPME (DI-SPME-HPLC) analysis of the phytohormones in cucumber, tomato, date palm, and calendula samples.

Effect of the Hammett substituent constant of para-substituted benzoic acid on the perovskite/SnO2 interface passivation in perovskite solar cells

It is critical to design bifunctional passivation molecules to simultaneously passivate the charge transport layer and perovskite layer at the charge transport layer/perovskite interface in perovskite solar cells (PSCs). In this study, we investigate the effect of para-substituted benzoic acid with different Hammett constants (σ) on the photovoltaic performance of PSCs. Two passivation molecules 4-aminomethylbenzoic acid (4-AMBA) and 4-sulfamoylbenzoic acid (4-SABA) are used to passivate the SnO2 surface with carboxylic acid and the perovskite with para-substituent electron-donating -CH2NH2 (σ = ca. -0.02) and electron-withdrawing -SO2NH2 (σ = ca. +0.60). Compared with non-passivated PSC, the passivation improves the power conversion efficiency (PCE) mainly due to the increased open-circuit voltage (VOC) and fill factor (FF), where the -SO2NH2 substituent is better in improving the photovoltaic performance than the -CH2NH2 one. The trap density is more reduced and the charge extraction ability is more improved by 4-SABA than by 4-AMBA, which indicates that the weak electron-withdrawing nature of a para-substituent such as -SO2NH2 is better for the passivation of the bottom perovskite than a weak electron-donating -CH2NH2 substituent. Consequently, the passivation with 4-SABA enhances the PCE from 22.27% to 23.64%, along with improved long-term stability. This work highlights for the first time the role of the Hammett constant in the surface passivation of PSCs.

Antireflective Superhydrophobic and Robust Coating Based on Chitin Nanofibers and Methylsilanized Silica for Outdoor Applications

Antireflective coatings with superhydrophobicity have many outdoor applications, such as solar photovoltaic panels and windshields. In this study, we fabricated an omnidirectional antireflective and superhydrophobic coating with good mechanical robustness and environmental durability via the spin coating technique. The coating consisted of a layer of phytic acid (PA)/polyacrylamide (PAM)/calcium ions (Ca2+) (referred to as Binder), an antireflective layer composed of chitin nanofibers (ChNFs), and a hydrophobic layer composed of methylsilanized silica (referred to as Mosil). The transmittance of a glass slide with the Binder/ChNFs/Mosil coating had a 5.2% gain at a wavelength of 550 nm, and the antireflective coating showed a water contact angle as high as 160° and a water sliding angle of 8°. The mechanical robustness and environmental durability of the coating, including resistance to peeling, dynamic impact, chemical erosion, ultraviolet (UV) irradiation, and high temperature, were evaluated. The coating retained excellent antireflective capacity and self-cleaning performance in the harsh conditions. The increase in voltage per unit area of a solar panel with a Binder/ChNFs/Mosil coating reached 0.4 mV/cm2 compared to the solar panel exposed to sunlight with an intensity of 54.3 × 103 lx. This work not only demonstrates that ChNFs can be used as raw materials to fabricate antireflective superhydrophobic coatings for outdoor applications but also provides a feasible and efficient approach to do so.

Competitive Valerate Binding Enables RuO2-Mediated Butene Electrosynthesis in Water

The (non)-Kolbe oxidation of valeric acid, sourced from a hydrolysis product of cellulose, provides a sustainable synthetic route to access value-added products, such as butene. An essential mechanistic step preceding product formation involves the oxidative and decarboxylative cleavage of a C-C bond. Yet, the role of the electrode surface in mediating this oxidative step remains an open question: the electron transfer can occur either via an inner-sphere or outer-sphere mechanism. Here, we report the electrochemical, in situ spectroscopic, computational, and reactivity studies of RuO2-mediated oxidative decarboxylation of valeric acid to butene in aqueous electrolytes. We find that carboxylates bind to RuO2 anode surfaces at potential values where decarboxylation products are observed. Our results are consistent with a reaction scheme where the competitive and catalytic oxygen evolution reaction (OER) is impeded by these bound carboxylate species while these species are inert toward butene formation. Our results implicate an outer-sphere electron transfer mechanism for decarboxylation where the surface chemistry of the RuO2 electrode serves to enable higher non-Kolbe reaction selectivity by suppressing the parasitic OER. Our findings delineate interfacial design principles for selective electrochemical systems that utilize water as the ultimate oxidant for sustainable decarboxylation.

Reducing nonradiative recombination for highly efficient inverted perovskite solar cells via a synergistic bimolecular interface

Reducing interface nonradiative recombination is important for realizing highly efficient perovskite solar cells. In this work, we develop a synergistic bimolecular interlayer (SBI) strategy via 4-methoxyphenylphosphonic acid (MPA) and 2-phenylethylammonium iodide (PEAI) to functionalize the perovskite interface. MPA induces an in-situ chemical reaction at the perovskite surface via forming strong P-O-Pb covalent bonds that diminish the surface defect density and upshift the surface Fermi level. PEAI further creates an additional negative surface dipole so that a more n-type perovskite surface is constructed, which enhances electron extraction at the top interface. With this cooperative surface treatment, we greatly minimize interface nonradiative recombination through both enhanced defect passivation and improved energetics. The resulting p-i-n device achieves a stabilized power conversion efficiency of 25.53% and one of the smallest nonradiative recombination induced Voc loss of only 59 mV reported to date. We also obtain a certified efficiency of 25.05%. This work sheds light on the synergistic interface engineering for further improvement of perovskite solar cells.

Thiol-Functionalized Adsorbents through Atomic Layer Deposition and Vapor-Phase Silanization for Heavy Metal Ion Removal

The removal of toxic heavy metal ions from water resources is crucial for environmental protection and public health. In this study, we address this challenge by developing a surface functionalization technique for the selective adsorption of these contaminants. Our approach involves atomic layer deposition (ALD) followed by vapor-phase silanization of porous substrates. We utilized porous silica gel powder (∼100 μm particles, 89 m2/g surface area, ∼30 nm pores) as an initial substrate. This powder was first coated with ∼0.5 nm ALD Al2O3, followed by vapor-phase grafting of a thiol-functional silane. The modified powder, particularly in acidic conditions (pH = 4), showed high selectivity in adsorbing Cd(II), As(V), Pb(II), Hg(II), and Cu(II) heavy metal ions in mixed ion solutions over common benign ions (e.g., Na, K, Ca, and Mg). Langmuir adsorption isotherms and breakthrough adsorption studies were conducted to assess heavy metal binding affinity and revealed the order of Cd(II) < Pb(II) < Cu(II) < As(V) < Hg(II), with a significantly higher affinity for As(V) and Hg(II) ions. Time-dependent uptake studies demonstrated rapid removal of heavy metal ions from aqueous environments, with Hg(II) exhibiting the fastest adsorption kinetics on thiol-modified surfaces. These findings highlight the potential of ALD and vapor-phase silanization to create effective adsorbents for the targeted removal of hazardous contaminants from water.

Rationale Design for Anchoring Pendant Groups of Zwitterionic Polymeric Medical Coatings

A biocompatible and antifouling polymeric medical coating was developed through rational design for anchoring pendant groups for the modification of stainless steel. Zwitterionic 2-methacryloyloxyethyl phosphorylcholine (MPC) was copolymerized individually with three anchoring monomers of carboxyl acrylamides with different alkyl spacers, including acryloylglycine (2-AE), 6-acrylamidohexanoic acid (6-AH), and 11-acrylamidoundecanoic acid (11-AU). The carboxylic acid groups are responsible for the stable grafting of copolymers onto stainless steel via a coordinative interaction with metal oxides. Due to hydrophobic interaction and hydrogen bonding, the anchoring monomers enable the formation of self-assembling structures in solution and at a metallic interface, which can play an important role in the thin film formation and functionality of the coatings. Therefore, surface characterizations of anchoring monomers on stainless steel were conducted to analyze the packing density and strength of the intermolecular hydrogen bonds. The corresponding copolymers were synthesized, and their aggregate structures were assessed, showing micelle aggregation for copolymers with higher hydrophobic compositions. The synergistic effects of inter/intramolecular interactions and hydrophobicity of the anchoring monomers result in the diversity of the thickness, surface coverage, wettability, and friction of the polymeric coatings on stainless steel. More importantly, the antifouling properties of the coatings against bacteria and proteins were strongly correlated to thin film formation. Ultimately, the key lies in deciphering the molecular structure of the anchoring pendants in thin film formation and assessing the effectiveness of the coatings, which led to the development of medical coatings through the graft-onto approach.

Self-Assembled Chiral Film Based on Melanin Polymers

Chirality plays a fundamental role in natural phenomena, yet its manifestation on solid surfaces remains relatively unexplored. In this study, we investigate the formation of chiroptical melanin-based self-assembled films on quartz substrates, leveraging mussel-inspired surface chemistry. Water-soluble porphyrins serve as molecular synthons, facilitating the spontaneous formation of hetero-aggregates in phosphate-buffered saline containing L- or D-DOPA. Spectroscopic analysis reveals chiral transfer from DOPA enantiomers to porphyrin hetero-aggregates, followed by the disruption of these latter and subsequent generation of chiral melanin structures in solution. Quartz substrates inserted into these solutions spontaneously accumulate homogeneous melanin-like films over days, demonstrating the feasibility of self-assembly. The resulting films exhibit characteristic UV/Vis and CD spectra, with distinct signals indicating successful chiral induction. Interestingly, the AFM characterizations reveal a distinct surface morphology, and in addition, some thermal and mechanical properties have been taken into account. Overall, this study sheds light on the formation, stability, and chiroptical properties of melanin-based films, paving the way for their application in various fields.

Beyond the Gold-Thiol Paradigm: Exploring Alternative Interfaces for Electrochemical Nucleic Acid-Based Sensing

Nucleic acid-based electrochemical sensors (NBEs) use oligonucleotides as affinity reagents for the detection of a variety of targets, ranging from small-molecule therapeutics to whole viruses. Because of their versatility in molecular sensing, NBEs are being developed broadly for diagnostic and biomedical research applications. Benchmark NBEs are fabricated via self-assembly of thiol-based monolayers on gold. Although robust for rapid prototyping, thiol monolayers suffer from limitations in terms of stability under voltage modulation and in the face of competitive ligands such as thiolated molecules naturally occurring in biofluids. Additionally, gold cannot be deployed as an NBE substrate for all biomedical applications, such as in cases where molecular measurements coupled to real-time, under-the-sensor tissue imaging is needed. Seeking to overcome these limitations, the field of NBEs is pursuing alternative ligands and electrode surfaces. In this perspective, I discuss new interface fabrication strategies that have successfully achieved NBE sensing, or that have the potential to allow NBE sensing on conductive surfaces other than gold. I hope this perspective will provide the reader with a fresh view of how future NBE interfaces could be constructed and will serve as inspiration for the pursuit of collaborative developments in the field of NBEs.

Air Corrosion of Layered Cathode Materials for Sodium-Ion Batteries: Cation Mixing and a Practical Suppression Strategy

Layered oxide cathodes of sodium-ion batteries (SIBs) are considered promising candidates due to their fascinating high capacity, good cyclability, and environmental friendliness. However, the air sensitivity of layered SIB cathodes causes high electrode manufacturing costs and performance deterioration, hampering their practical application. Herein, a commercial O3-type layered Na(Ni1/3Fe1/3Mn1/3)O2 (NNFM) material is adopted to investigate the air corrosive problem and the suppression strategy. We reveal that once the layered material comes in contact with ambient air, cations migrate from transition metal (TM) layers to sodium layers at the near surface, although Na+ and TM ions show quite different ion radii. Experimental results and theoretical calculations show that more Ni/Na disorder occurs in the air-exposed O3-NNFM materials, owing to a lower Ni migration energy barrier. The cation mixing results in detrimental structural distortion, along with the formation of residual alkali species on the surface, leading to high impedance for Na+ diffusion during charge/discharge. To tackle this problem, an ultrathin and uniform hydrophobic molecular layer of perfluorodecyl trimethoxysilane is assembled on the O3-NNFM surface, which significantly suppresses unfavorable chemistry and structure degradation during air storage. The in-depth understanding of the structural degradation mechanism and suppression strategy presented in this work can facilitate high-energy cathode manufacturing from the perspective of future practical implementation and commercialization.

Preparation of Superhydrophobic Coating on X80 Steel and Its Corrosion Resistance in Oilfield Produced Water

Corrosion is an unavoidable issue that steel encounters during service; however, the generic methods employed for corrosion prevention often need high cost or preparation conditions. In this study, a facile chemical replacement deposition method was proposed to realize an anticorrosion superhydrophobic coating on a X80 steel surface. The growth mechanism of the rough structure and its impact on the wettability of the superhydrophobic coating were analyzed. The superhydrophobic coating, deposited for 50 s and modified for 30 min, achieved optimal electrochemical properties and a maximum water contact angle. The immersion test, in the saturated CO2 oilfield produced water, demonstrated the better corrosion resistance of superhydrophobic coating than X80 steel. Correspondingly, a kinetic corrosion model was established to analyze the anticorrosion mechanism. In summary, this method significantly improves the corrosion resistance of X80 steel and is attractive for other industrial fields.

LiF-Rich Solid Electrolyte Interphase Formation by Establishing Sacrificial Layer on the Separator

The formation of a stable solid electrolyte interphase (SEI) layer is crucial for enhancing the safety and lifespan of Li metal batteries. Fundamentally, a homogeneous Li+ behavior by controlling the chemical reaction at the anode/electrolyte interface is the key to establishing a stable SEI layer. However, due to the highly reactive nature of Li metal anodes (LMAs), controlling the movement of Li+ at the anode/electrolyte interface remains challenging. Here, an advanced approach is proposed for coating a sacrificial layer called fluorinated self-assembled monolayer (FSL) on a boehmite-coated polyethylene (BPE) separator to form a stable SEI layer. By leveraging the strong affinity between the fluorine functional group and Li+, the rapid formation of a LiF-rich SEI layer in the cell production and early cycling stage is facilitated. This initial stable SEI formation promotes the subsequent homogeneous Li+ flux, thereby improving the LMA stability and yielding an enhanced battery lifespan. Further, the mechanism behind the stable SEI layer generation by controlling the Li+ dynamics through the FSL-treated BPE separator is comprehensively verified. Overall, this research offers significant contributions to the energy storage field by addressing challenges associated with LMAs, thus highlighting the importance of interfacial control in achieving a stable SEI layer.

Spin crossover in {Fe(pyrazine)[M(CN)4]} (M = Ni, Pt) thin films assembled on fused silica substrates

Thin films with thicknesses in the range between ca. 10-50 nm of the spin crossover (SCO) compound {Fe(pyrazine)[μ4-M(CN)4]} (M = Ni, Pt) have been deposited on fused silica substrates using a sequential assembly method and 4-pyridinecarboxylic acid as anchoring layer. Film morphology and crystallinity were assessed by means of atomic force microscopy and grazing incidence X-ray diffraction, respectively. The intensity of the π-π* transition of the pyrazine ligand at 270 nm, being rather insensitive to the spin state of the complex, was used to follow the film growth as a function of different deposition parameters. On the other hand, the spin state changes were inferred from the temperature dependence of absorption bands appearing at 540, 490 and 310 nm in the low spin state. In line with their amorphous nature, each film displays a very gradual thermal spin crossover between ca. 100-300 K, independently of its thickness and deposition conditions. These results are not only interesting to better understand the effects of size reduction and organization on the SCO phenomenon, but the deposition of these SCO compounds on electrically insulating and/or optically transparent oxide surfaces opens also the door for various photonic or electronic applications.

Peptide-based self-assembled monolayers (SAMs): what peptides can do for SAMs and vice versa

Self-assembled monolayers (SAMs) represent highly ordered molecular materials with versatile biochemical features and multidisciplinary applications. Research on SAMs has made much progress since the early begginings of Au substrates and alkanethiols, and numerous examples of peptide-displaying SAMs can be found in the literature. Peptides, presenting increasing structural complexity, stimuli-responsiveness, and biological relevance, represent versatile functional components in SAMs-based platforms. This review examines the major findings and progress made on the use of peptide building blocks displayed as part of SAMs with specific functions, such as selective cell adhesion, migration and differentiation, biomolecular binding, advanced biosensing, molecular electronics, antimicrobial, osteointegrative and antifouling surfaces, among others. Peptide selection and design, functionalisation strategies, as well as structural and functional characteristics from selected examples are discussed. Additionally, advanced fabrication methods for dynamic peptide spatiotemporal presentation are presented, as well as a number of characterisation techniques. All together, these features and approaches enable the preparation and use of increasingly complex peptide-based SAMs to mimic and study biological processes, and provide convergent platforms for high throughput screening discovery and validation of promising therapeutics and technologies.

Phosphonic acid anchored tripodal molecular films on indium tin oxide

Whereas monopodal self-assembling monolayers (SAMs) are most frequently used for surface and interface engineering, tripodal SAMs are less popular due to the difficulty in achieving a reliable and homogeneous bonding configuration. In this context, in the present study, the potential of phosphonic acid (PA) decorated triptycene (TripPA) for formation of SAMs on oxide substrates was studied, using indium tin oxide (ITO) as a representative and application-relevant test support. A combination of several complementary experimental techniques was applied and a suitable monopodal reference system, benzylphosphonic acid (PPA), was used. The resulting data consistently show that TripPA forms well-defined, densely packed, and nearly contamination-free tripodal SAMs on ITO, with the similar parameters and properties as the monopodal reference system. Modification of wetting properties and work function of ITO by non-substituted and cyano-decorated TripPA SAMs was demonstrated, showing a potential of this tripodal system for surface engineering of oxide substrates.

Cerium Oxide Catalyzed Disproportionation of Hydrogen Peroxide: A Closer Look at the Reaction Intermediate

Cerium oxide nanoparticles (CNPs) have recently gained increasing interest as redox enzyme-mimetics to scavenge the intracellular excess of reactive oxygen species, including hydrogen peroxide (H2 O2 ). Despite the extensive exploration, there remains a notable discrepancy regarding the interpretation of observed redshift of UV-Visible spectroscopy due to H2 O2 addition and the catalase-mimicking mechanism of CNPs. To address this question, we investigated the reaction mechanism by taking a closer look at the reaction intermediate during the catalase mimicking reaction. In this study, we present evidence demonstrating that in aqueous solutions, H2 O2 adsorption at CNP surface triggers the formation of stable intermediates known as cerium-peroxo (Ce-O2 2- ) and/or cerium-hydroperoxo (Ce-OOH- ) complexes as resolved by Raman scattering and UV-Visible spectroscopy. Polymer coating presents steric hinderance for H2 O2 accessibility to the solid-liquid interface limiting further intermediate formation. We demonstrate in depth that the catalytic reactivity of CNPs in the H2 O2 disproportionation reaction increases with the Ce(III)-fraction and decreases in the presence of polymer coatings. The developed approach using UV-Visible spectroscopy for the characterization of the surface peroxide species can potentially serve as a foundation for determining the catalytic reactivity of CNPs in the disproportionation of H2 O2 .

Surface (bio)-functionalization of metallic materials: How to cope with real interfaces?

Metallic materials are an important class of biomaterials used in various medical devices, owing to a suitable combination of their mechanical properties. The (bio)-functionalization of their surfaces is frequently performed for biocompatibility requirements, as it offers a powerful way to control their interaction with biological systems. This is particularly important when physicochemical processes and biological events, mainly involving proteins and cells, are initiated at the host-material interface. This review addresses the state of "real interfaces" in the context of (bio)-functionalization of metallic materials, and the necessity to cope with it to avoid frequent improper evaluation of the procedure used. This issue is, indeed, well-recognized but often neglected and emerges from three main issues: (i) ubiquity of surface contamination with organic compounds, (ii) reactivity of metallic surfaces in biological medium, and (iii) discrepancy in (bio)-functionalization procedures between expectations and reality. These disturb the assessment of the strategies adopted for surface modifications and limit the possibilities to provide guidelines for their improvements. For this purpose, X-ray photoelectrons spectroscopy (XPS) comes to the rescue. Based on significant progresses made in methodological developments, and through a large amount of data compiled to generate statistically meaningful information, and to insure selectivity, precision and accuracy, the state of "real interfaces" is explored in depth, while looking after the two main constituents: (i) the bio-organic adlayer, in which the discrimination between the compounds of interest (anchoring molecules, coupling agents, proteins, etc) and organic contaminants can be made, and (ii) the metallic surface, which undergoes dynamic processes due to their reactivity. Moreover, through one of the widespread (bio)-functionalization strategy, given as a case study, a particular attention is devoted to describe the state of the interface at different stages (composition, depth distribution of contaminants and (bio)compounds of interest) and the mode of protein retention. It is highlighted, in particular, that the occurrence or improvement of bioactivity does not demonstrate that the chemical schemes worked in reality. These aspects are particularly essential to make progress on the way to choose the suitable (bio)-functionalization strategy and to provide guidelines to improve its efficiency.

Multifunctional Aluminum Pre-treatments from End-Functionalized Phosphonic Acid Self-Assembled Monolayers

Aluminum alloys are used in advanced engineering applications as they possess a combination of favorable properties, including high strength, lightweightness, good corrosion resistance, machineability, and recyclability. Such applications often require forming the sheets into the final components, which is typically aided by an oil-based lubricant, followed by joining them using adhesives, which is hampered by residual lubricant. In this work, aluminum surfaces were modified with different self-assembled monolayers (SAMs), with the goal of significantly reducing the amount of lubricant while simultaneously improving friction properties, forming, and bonding performance. Our results show that SAMs terminated with hydrophilic and nucleophilic end groups give rise to high-energy surfaces with wetting properties that are stable over time. These surfaces showed significantly improved surface wetting by the lubricant, which in turn resulted in an improved forming performance at reduced lubricant coat weights. Moreover, the nucleophilic SAM termination provided outstanding performance in adhesive bonding tests under corrosive conditions.

Rational Design of Stimuli-Responsive Inorganic 2D Materials via Molecular Engineering: Toward Molecule-Programmable Nanoelectronics

The ability of electronic devices to act as switches makes digital information processing possible. Succeeding graphene, emerging inorganic 2D materials (i2DMs) have been identified as alternative 2D materials to harbor a variety of active molecular components to move the current silicon-based semiconductor technology forward to a post-Moore era focused on molecule-based information processing components. In this regard, i2DMs benefits are not only for their prominent physiochemical properties (e.g., the existence of bandgap), but also for their high surface-to-volume ratio rich in reactive sites. Nonetheless, since this field is still in an early stage, having knowledge of both i) the different strategies for molecularly functionalizing the current library of i2DMs, and ii) the different types of active molecular components is a sine qua non condition for a rational design of stimuli-responsive i2DMs capable of performing logical operations at the molecular level. Consequently, this Review provides a comprehensive tutorial for covalently anchoring ad hoc molecular components-as active units triggered by different external inputs-onto pivotal i2DMs to assess their role in the expanding field of molecule-programmable nanoelectronics for electrically monitoring bistable molecular switches. Limitations, challenges, and future perspectives of this emerging field which crosses materials chemistry with computation are critically discussed.

Self-Assembled Monolayers of Push-Pull Chromophores as Active Layers and Their Applications

In recent decades, considerable attention has been focused on the design and development of surfaces with defined or tunable properties for a wide range of applications and fields. To this end, self-assembled monolayers (SAMs) of organic compounds offer a unique and straightforward route of modifying and engineering the surface properties of any substrate. Thus, alkane-based self-assembled monolayers constitute one of the most extensively studied organic thin-film nanomaterials, which have found wide applications in antifouling surfaces, the control of wettability or cell adhesion, sensors, optical devices, corrosion protection, and organic electronics, among many other applications, some of which have led to their technological transfer to industry. Nevertheless, recently, aromatic-based SAMs have gained importance as functional components, particularly in molecular electronics, bioelectronics, sensors, etc., due to their intrinsic electrical conductivity and optical properties, opening up new perspectives in these fields. However, some key issues affecting device performance still need to be resolved to ensure their full use and access to novel functionalities such as memory, sensors, or active layers in optoelectronic devices. In this context, we will present herein recent advances in π-conjugated systems-based self-assembled monolayers (e.g., push-pull chromophores) as active layers and their applications.

Catalyst-Free Amino-Yne Click Reaction: An Efficient Way for Immobilizing Amoxicillin onto Polymeric Surfaces

Surface modifications play a crucial role in enhancing the functionality of biomaterials. Different approaches can be followed in order to achieve the bioconjugation of drugs and biological compounds onto polymer surfaces. In this study, we focused on the immobilization of an amoxicillin antibiotic onto the surface of poly-L-lactic acid (PLLA) using a copper-free amino-yne click reaction. The utilization of this reaction allowed for a selective and efficient bioconjugation of the amoxicillin moiety onto the PLLA surface, avoiding copper-related concerns and ensuring biocompatibility. The process involved sequential steps that included surface activation via alkaline hydrolysis followed by an amidation reaction with ethylendiamine, functionalization with propiolic groups, and subsequent conjugation with amoxicillin via a click chemistry approach. Previous amoxicillin immobilization using tryptophan and fluorescent amino acid conjugation was carried out in order to determine the efficacy of the proposed methodology. Characterization techniques such as X-ray photoelectron spectroscopy (XPS), Attenuated Total Reflection (ATR)-Fourier Transform Infrared (FTIR) spectroscopy, surface imaging, water contact angle determination, and spectroscopic analysis confirmed the successful immobilization of both tryptophan and amoxicillin while maintaining the integrity of the PLLA surface. This tailored modification not only exhibited a novel method for surface functionalization but also opens avenues for developing antimicrobial biomaterials with improved drug-loading capacity.

From Corrosion Casting to Virtual Dissection: Contrast-Enhanced Vascular Imaging using Hafnium Oxide Nanocrystals

Vascular corrosion casting is a method used to visualize the three dimensional (3D) anatomy and branching pattern of blood vessels. A polymer resin is injected in the vascular system and, after curing, the surrounding tissue is removed. The latter often deforms or even fractures the fragile cast. Here, a method is proposed that does not require corrosion, and is based on in situ micro computed tomography (micro-CT) scans. To overcome the lack of CT contrast between the polymer cast and the animals' surrounding soft tissue, hafnium oxide nanocrystals (HfO2 NCs) are introduced as CT contrast agents into the resin. The NCs dramatically improve the overall CT contrast of the cast and allow for straightforward segmentation in the CT scans. Careful design of the NC surface chemistry ensures the colloidal stability of the NCs in the casting resin. Using only 5 m% of HfO2 NCs, high-quality cardiovascular casts of both zebrafish and mice can be automatically segmented using CT imaging software. This allows to differentiate even μ $\umu$ m-scale details without having to alter the current resin injection methods. This new method of virtual dissection by visualizing casts in situ using contrast-enhanced CT imaging greatly expands the application potential of the technique.

Superhydrophilic and Antifriction Thin Hydrogel Formed under Mild Conditions for Medical Bare Metal Guide Wires

Medical guide wires play a crucial role in the process of intravascular interventional therapy. However, it is essential for bare metal guide wires to possess both hydrophilic lubricity and coating durability, avoiding tissue damage caused by friction inside the blood vessel during the interventional procedure. Additionally, it is still a huge challenge for diverse metal materials to bind with polymer coatings easily. Herein, we present a hydrogel coating scheme and its preparation method for various wires under mild conditions for environmental protection purposes. The preparation process involves surface pretreatment, including low-temperature heating and silanization, followed by a two-step dip coating and ultraviolet polymerization. The whole process leads to the formation of an interpenetrating cross-linked hydrogel network from the substrate to the surface section. This study confirms the superhydrophilicity and lubricity of three metal wires with the designed coating, especially reducing the friction significantly by ≥ 95%. The thin coating (average thickness <6.2 μm) demonstrates strong adhesion with various substrates and exhibits resistance to 25 or even 125 cycles of friction, indicating excellent stability and preventing easy detachment. The finally prepared composite nickel-titanium (NiTi) guide wire with stainless steel (SS) and platinum-tungsten (Pt-W) coils (overall diameter of ∼0.36 mm) shows satisfactory performance with a friction of 0.183 N for 25 cycles, meeting the clinical requirements (average friction ≤0.2 N) for interventional operation. These findings highlight the potential of this study in advancing the development of medical devices, particularly in the field of intravascular interventional therapy.

Ligand-Directed Shape Reconfiguration in Inorganic Materials

Polymer elastomers with reversible shape-changing capability have led to significant development of artificial muscles, functional devices, and soft robots. By contrast, reversible shape transformation of inorganic nanoparticles is notoriously challenging due to their relatively rigid lattice structure. Here, the authors demonstrate the synthesis of shape-changing nanoparticles via an asymmetrical surface functionalization process. Various ligands are investigated, revealing the essential role of steric hindrance from the functional groups. By controlling the unbalanced structural hindrance on the surface, the as-prepared clay nanoparticles can transform their shape in a fast, facile, and reversible manner. In addition, such flexible morphology-controlled mechanism provides a platform for developing self-propelled shape-shifting nanocollectors. Owing to the ion-exchanging capability of clay, these self-propelled nanoswimmers (NS) are able to autonomously adsorb rare earth elements with ultralow concentration, indicating the feasibility of using naturally occurring materials for self-powered nanomachine.

Cholesterol-Enriched Hybrid Lipid Bilayer Formation on Inverse Phosphocholine Lipid-Functionalized Titanium Oxide Surfaces

Hybrid lipid bilayers (HLBs) are rugged biomimetic cell membrane interfaces that can form on inorganic surfaces and be designed to contain biologically important components like cholesterol. In general, HLBs are formed by depositing phospholipids on top of a hydrophobic self-assembled monolayer (SAM) composed of one-tail amphiphiles, while recent findings have shown that two-tail amphiphiles such as inverse phosphocholine (CP) lipids can have advantageous properties to promote zwitterionic HLB formation. Herein, we explored the feasibility of fabricating cholesterol-enriched HLBs on CP SAM-functionalized TiO2 surfaces with the solvent exchange and vesicle fusion methods. All stages of the HLB fabrication process were tracked by quartz crystal microbalance-dissipation (QCM-D) measurements and revealed important differences in fabrication outcome depending on the chosen method. With the solvent exchange method, it was possible to fabricate HLBs with well-controlled cholesterol fractions up to ~65 mol% in the upper leaflet as confirmed by a methyl-β-cyclodextrin (MβCD) extraction assay. In marked contrast, the vesicle fusion method was only effective at forming HLBs from precursor vesicles containing up to ~35 mol% cholesterol, but this performance was still superior to past results on hydrophilic SiO2. We discuss the contributing factors to the different efficiencies of the two methods as well as the general utility of two-tail CP SAMs as favorable interfaces to incorporate cholesterol into HLBs. Accordingly, our findings support that the solvent exchange method is a versatile tool to fabricate cholesterol-enriched HLBs on CP SAM-functionalized TiO2 surfaces.

Selective Tumor Hypoxia Targeting Using M75 Antibody Conjugated Photothermally Active MoOx Nanoparticles

Photothermal therapy (PTT) mediated at the nanoscale has a unique advantage over currently used cancer treatments, by being spatially highly specific and minimally invasive. Although PTT combats traditional tumor treatment approaches, its clinical implementation has not yet been successful. The reasons for its disadvantage include an insufficient treatment efficiency or low tumor accumulation. Here, we present a promising new PTT platform combining a recently emerged two-dimensional (2D) inorganic nanomaterial, MoOx, and a tumor hypoxia targeting element, the monoclonal antibody M75. M75 specifically binds to carbonic anhydrase IX (CAIX), a hypoxia marker associated with many solid tumors with a poor prognosis. The as-prepared nanoconjugates showed highly specific binding to cancer cells expressing CAIX while being able to produce significant photothermal yield after irradiation with near-IR wavelengths. Small aminophosphonic acid linkers were recognized to be more effective over the combination of poly(ethylene glycol) chain and biotin-avidin-biotin bridge in constructing a PTT platform with high tumor-binding efficacy. The in vitro cellular uptake of nanoconjugates was visualized by high-resolution fluorescence microscopy and label-free live cell confocal Raman microscopy. The key to effective cancer treatment may be the synergistic employment of active targeting and noninvasive, tumor-selective therapeutic approaches, such as nanoscale-mediated PTT. The use of active targeting can streamline nanoparticle delivery increasing photothermal yield and therapeutic success.

Partial Hydrolysis of Diphosphonate Ester During the Formation of Hybrid TiO2 Nanoparticles: Role of Acid Concentration

The hydrolysis of the phosphonate ester linker during the synthesis of hybrid (organic-inorganic) TiO2 nanoparticles is important when forming porous hybrid organic-inorganic metal phosphonates. In the present work, a method was utilized to control the in-situ partial hydrolysis of diphosphonate ester in the presence of a titania precursor as a function of acid content, and its impact on the hybrid nanoparticles was assessed. Organodiphosphonate esters, and more specific, their hydrolysis degree during the formation of hybrid organic-inorganic metal oxide nanoparticles, are relatively under explored as linkers. Here, a detailed analysis on the hydrolysis of tetraethyl propylene diphosphonate ester (TEPD) as diphosphonate linker to produce hybrid TiO2 nanoparticles is discussed as a function of acid content. Quantitative solution NMR spectroscopy revealed that during the synthesis of TiO2 nanoparticles, an increase in acid concentration introduces a higher degree of partial hydrolysis of the TEPD linker into diverse acid/ester derivatives of TEPD. Increasing the HCl/Ti ratio from 1 to 3, resulted in an increase in degree of partial hydrolysis of the TEPD linker in solution from 4 % to 18.8 % under the applied conditions. As a result of the difference in partial hydrolysis, the linker-TiO2 bonding was altered. Upon subsequent drying of the colloidal TiO2 solution, different textures, at nanoscale and macroscopic scale, were obtained dependent on the HCl/Ti ratio and thus the degree of hydrolysis of TEPD. Understanding such linker-TiO2 nanoparticle surface dynamics is crucial for making hybrid organic-inorganic materials (i. e. (porous) metal phosphonates) employed in applications such as electronic/photonic devices, separation technology and heterogeneous catalysis.

Obtaining extended insight into molecular systems by probing multiple pathways in second-order nonlinear spectroscopy

Second-order nonlinear spectroscopy is becoming an increasingly important technique in the study of interfacial systems owing to its marked ability to study molecular structures and interactions. The properties of such a system under investigation are contained within their intrinsic second-order susceptibilities which are mapped onto the measured nonlinear signals (e.g. sum-frequency generation) through the applied experimental settings. Despite this yielding a plethora of information, many crucial aspects of molecular systems typically remain elusive, for example the depth distributions, molecular orientation and local dielectric properties of its constituent chromophores. Here, it is shown that this information is contained within the phase of the measured signal and, critically, can be extracted through measurement of multiple nonlinear pathways (both the sum-frequency and difference-frequency output signals). Furthermore, it is shown that this novel information can directly be correlated to the characteristic vibrational spectra, enabling a new type of advanced sample characterization and a profound analysis of interfacial molecular structures. The theory underlying the different contributions to the measured phase of distinct nonlinear pathways is derived, after which the presented phase disentanglement methodology is experimentally demonstrated for model systems of self-assembled monolayers on several metallic substrates. The obtained phases of the local fields are compared to the corresponding phases of the nonlinear Fresnel factors calculated through the commonly used theoretical model, the three-layer model. It is found that, despite its rather crude assumptions, the model yields remarkable similarity to the experimentally obtained values, thus providing validation of the model for many sample classes.

An Evaluation of Parylene Thin Films to Prevent Encrustation for a Urinary Bladder Pressure MEMS Sensor System

Recent developments in urological implants have focused on preventive strategies to mitigate encrustation and biofilm formation. Parylene, a conformal, pinhole-free polymer coating, has gained attention due to its high biocompatibility and chemical resistance, excellent barrier properties, and low friction coefficient. This study aims to evaluate the effectiveness of parylene C in comparison to a parylene VT4 grade coating in preventing encrustation on a urinary bladder pressure MEMS sensor system. Additionally, silicon oxide (SiOx) applied as a finish coating was investigated for further improvements. An in vitro encrustation system mimicking natural urine flow was used to quantify the formation of urinary stones. These stones were subsequently analyzed using Fourier transform infrared spectrometry (FTIR). Encrustation results were then discussed in relation to coating surface chemical properties. Parylene C and VT4 grades demonstrated a very low encrustation mass, making them attractive options for encrustation prevention. The best performance was achieved after the addition of a hydrophilic SiOx finish coating on parylene VT4 grade. Parylene-based encapsulation proved to be an outstanding solution to prevent encrustation for urological implants.

Polythiophene as a Double-Electrostatic Template for Zinc Oxide and Gold: Multicomponent Nano-Objects for Enhanced Photocatalysis

Using electrostatic self-assembly and electrostatic nanotemplating, a quaternary nanostructured system consisting of zinc oxide nanoparticles, gold nanoparticles, poly[3-(potassium-4-butanoate)thiophene-2,5-diyl] (PT), and methyltrioctylammonium chloride (MTOA) (PT-MTOA-ZnO-Au) was designed for aqueous photocatalysis. The PT-MTOA hollow sphere aggregates served as an electrostatic template for both individual inorganic nanoparticles controlling their morphology, stabilizing the nanoparticles, and acting as a photosensitizer. The hybrid structures included spherical ZnO nanoparticles with a diameter of d = 2.6 nm and spherical Au nanoparticles with d = 6.0 nm embedded in PT-MTOA hollow spheres with a hydrodynamic radius of R_H = 100 nm. The ZnO nanoparticles acted as the main catalyst, while the Au nanoparticles acted as the cocatalyst. As a photocatalytic model reaction, the dye degradation of methylene blue in aqueous solution using the full spectral range from UV to visible light was tested. The photocatalytic activity was optimized by varying the Zn and Au loading ratios and was substantially enhanced regarding the components; for example, it was increased by about 61% using PT-MTOA-ZnO-Au compared to the composite without gold particles. A photocatalytic mechanism of the methylene blue degradation was proposed when catalyzed by these multicomponent nano-objects. Thus, a simple procedure of templating two different nanoparticle species within the same cocatalytically active template has been demonstrated, which can be extended to other inorganic particles, making a variety of task-specific catalysts accessible.

Nanoparticulate Perovskites for Photocatalytic Water Reduction

SrTiO₃ and BaTiO₃ nanoparticles (NPs) were activated using H₂O₂ or aqueous HNO₃, and pristine and activated NPs were functionalized with a 2,2'-bipyridine phosphonic acid anchoring ligand (1), followed by reaction with RuCl₃^.3H₂O and bpy, RhCl₃^.3H₂O and bpy, or RuCl₃^.3H₂O. The surface-bound metal complex functionalized NPs were used for the photogeneration of H₂ from water, and their activity was compared to related systems using TiO₂ NPs. The role of pH during surface complexation was found to be important. The NPs were characterized using Fourier transform infrared (FTIR) and solid-state absorption spectroscopies, thermogravimetric analysis mass spectrometry (TGA-MS), and matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS), and the dihydrogen generation was analyzed using gas chromatography-mass spectrometry (GC-MS). Our findings indicate that extensively functionalized SrTiO₃ or BaTiO₃ NPs may perform better than TiO₂ NPs for water reduction.

Molecular Thin Films Enable the Synthesis and Screening of Nanoparticle Megalibraries Containing Millions of Catalysts

Megalibraries are centimeter-scale chips containing millions of materials synthesized in parallel using scanning probe lithography. As such, they stand to accelerate how materials are discovered for applications spanning catalysis, optics, and more. However, a long-standing challenge is the availability of substrates compatible with megalibrary synthesis, which limits the structural and functional design space that can be explored. To address this challenge, thermally removable polystyrene films were developed as universal substrate coatings that decouple lithography-enabled nanoparticle synthesis from the underlying substrate chemistry, thus providing consistent lithography parameters on diverse substrates. Multi-spray inking of the scanning probe arrays with polymer solutions containing metal salts allows patterning of >56 million nanoreactors designed to vary in composition and size. These are subsequently converted to inorganic nanoparticles via reductive thermal annealing, which also removes the polystyrene to deposit the megalibrary. Megalibraries with mono-, bi-, and trimetallic materials were synthesized, and nanoparticle size was controlled between 5 and 35 nm by modulating the lithography speed. Importantly, the polystyrene coating can be used on conventional substrates like Si/SiO_x, as well as substrates typically more difficult to pattern on, such as glassy carbon, diamond, TiO_2, BN, W, or SiC. Finally, high-throughput materials discovery is performed in the context of photocatalytic degradation of organic pollutants using Au-Pd-Cu nanoparticle megalibraries on TiO₂ substrates with 2,250,000 unique composition/size combinations. The megalibrary was screened within 1 h by developing fluorescent thin-film coatings on top of the megalibrary as proxies for catalytic turnover, revealing Au_0.53Pd_0.38Cu_0.09-TiO₂ as the most active photocatalyst composition.

Bimodal Antimicrobial Surfaces of Phytic Acid-Prussian Blue Nanoparticles-Cationic Polymer Networks

Surface modification plays a pivotal role in tailoring the functionalities of a solid material. Introduction of antimicrobial function on material surfaces can provide additional protection against life-threatening bacterial infections. Herein, a simple and universal surface modification method based on surface adhesion and electrostatic interaction of phytic acid (PA) is developed. PA is first functionalized with Prussian blue nanoparticles (PB NPs) via metal chelation and then conjugates with cationic polymers (CPs) through electrostatic interaction. With the aid of surface adherent PA and gravitation effect, the as-formed PA-PB-CP network aggregates are deposited on the solid materials in a substrate-independent manner. Synergistic bactericidal effects of "contact-killing" induced by the CPs and localized photothermal effect caused by the PB NPs endow the substrates with strong antibacterial performance. Membrane integrity, enzymatic activity, and metabolism function of the bacteria are disturbed in contact with the PA-PB-CP coating under near-infrared (NIR) irradiation. The PA-PB-CP modified biomedical implant surfaces exhibit good biocompatibility and synergistic antibacterial effect under NIR irradiation, and eliminate the adhered bacteria both in vitro and in vivo.

Synthesis of Stable Cerium Oxide Nanoparticles Coated with Phosphonic Acid-Based Functional Polymers

Functional polymers, such as poly(ethylene glycol) (PEG), terminated with a single phosphonic acid, hereafter PEG_ik-Ph are often applied to coat metal oxide surfaces during post-synthesis steps but are not sufficient to stabilize sub-10 nm particles in protein-rich biofluids. The instability is attributed to the weak binding affinity of post-grafted phosphonic acid groups, resulting in a gradual detachment of the polymers from the surface. Here, we assess these polymers as coating agents using an alternative route, namely, the one-step wet-chemical synthesis, where PEG_ik-Ph is introduced with cerium precursors during the synthesis. Characterization of the coated cerium oxide nanoparticles (CNPs) indicates a core-shell structure, where the cores are 3 nm cerium oxide and the shell consists of functionalized PEG polymers in a brush configuration. Results show that CNPs coated with PEG_1k-Ph and PEG_2k-Ph are of potential interest for applications as nanomedicines due to their high Ce(III) content and increased colloidal stability in cell culture media. We further demonstrate that the CNPs in the presence of hydrogen peroxide show an additional absorbance band in the UV-vis spectrum, which is attributed to Ce-O₂^2- peroxo-complexes and could be used in the evaluation of their catalytic activity for scavenging reactive oxygen species.

Modular and Substrate-Independent Grafting-To Procedure for Functional Polymer Coatings

The ability to tailor polymer brush coatings to the last nanometer has arguably placed them among the most powerful surface modification techniques currently available. Generally, the synthesis procedures for polymer brushes are designed for a specific surface type and monomer functionality and cannot be easily employed otherwise. Herein, we describe a modular and straightforward two-step grafting-to approach that allows introduction of polymer brushes of a desired functionality onto a large range of chemically different substrates. To illustrate the modularity of the procedure, gold, silicon oxide (SiO₂), and polyester-coated glass substrates were modified with five different block copolymers. In short, the substrates were first modified with a universally applicable poly(dopamine) primer layer. Subsequently, a grafting-to reaction was performed on the poly(dopamine) films using five distinct block copolymers, all of which contained a short poly(glycidyl methacrylate) segment and longer segment of varying chemical functionality. Ellipsometry, X-ray photoelectron spectroscopy, and static water contact angle measurements confirmed successful grafting of all five block copolymers to the poly(dopamine)-modified gold, SiO₂, and polyester-coated glass substrates. In addition, our method was used to provide direct access to binary brush coatings, by simultaneous grafting of two different polymer materials. The ability to synthesize binary brush coatings further adds to the versatility of our approach and paves the way toward production of novel multifunctional and responsive polymer coatings.

Fluorescence-Enhanced Microfluidic Biosensor Platform Based on Magnetic Beads with Highly Stable ZnO Nanorods for Biomarker Detection

Existing affinity-based fluorescence biosensing systems for monitoring of biomarkers often utilize a fixed solid substrate immobilized with capture probes limiting their use in continuous or intermittent biomarker detection. Furthermore, there have been challenges of integrating fluorescence biosensors with a microfluidic chip and low-cost fluorescence detector. Herein, we demonstrated a highly efficient and movable fluorescence-enhanced affinity-based fluorescence biosensing platform that can overcome the current limitations by combining fluorescence enhancement and digital imaging. Fluorescence-enhanced movable magnetic beads (MBs) decorated with zinc oxide nanorods (MB-ZnO NRs) were used for digital fluorescence-imaging-based aptasensing of biomolecules with improved signal-to-noise ratio. High stability and homogeneous dispersion of photostable MB-ZnO NRs were obtained by grafting bilayered silanes onto the ZnO NRs. The ZnO NRs formed on MB significantly improved the fluorescence signal up to 2.35 times compared to the MB without ZnO NRs. Moreover, the integration of a microfluidic device for flow-based biosensing enabled continuous measurements of biomarkers in an electrolytic environment. The results showed that highly stable fluorescence-enhanced MB-ZnO NRs integrated with a microfluidic platform have significant potential for diagnostics, biological assays, and continuous or intermittent biomonitoring.

pH-Mediated Size-Selective Adsorption of Gold Nanoparticles on Diblock Copolymer Brushes

Precise control of nanoparticles at interfaces can be achieved by designing stimuli-responsive surfaces that have tunable interactions with nanoparticles. In this study, we demonstrate that a polymer brush can selectively adsorb nanoparticles according to size by tuning the pH of the buffer solution. Specifically, we developed a facile polymer brush preparation method using a symmetric polystyrene-b-poly(2-vinylpyridine) (PS-b-P2VP) block copolymer deposited on a grafted polystyrene layer. This method is based on the assembly of a PS-b-P2VP thin film oriented with parallel lamellae that remains after exfoliation of the top PS-b-P2VP layer. We characterized the P2VP brush using X-ray reflectivity and atomic force microscopy. The buffer pH is used to tailor interactions between citrate-coated gold nanoparticles (AuNPs) and the top P2VP block that behaves like a polymer brush. At low pH (∼4.0) the P2VP brushes are strongly stretched and display a high density of attractive sites, whereas at neutral pH (∼6.5) the P2VP brushes are only slightly stretched and have fewer attractive sites. A quartz crystal microbalance with dissipation monitored the adsorption thermodynamics as a function of AuNP diameter (11 and 21 nm) and pH of the buffer. Neutral pH provides limited penetration depth for nanoparticles and promotes size selectivity for 11 nm AuNP adsorption. As a proof of concept, the P2VP brushes were exposed to various mixtures of large and small AuNPs to demonstrate selective capture of the smaller AuNPs. This study shows the potential of creating devices for nanoparticle size separations using pH-sensitive polymer brushes.

Neglected acidity pitfall: boric acid-anchoring hole-selective contact for perovskite solar cells

The spontaneous formation of self-assembly monolayer (SAM) on various substrates represents an effective strategy for interfacial engineering of optoelectronic devices. Hole-selective SAM is becoming popular among high-performance inverted perovskite solar cells (PSCs), but the presence of strong acidic anchors (such as -PO3H2) in state-of-the-art SAM is detrimental to device stability. Herein, we report for the first time that acidity-weakened boric acid can function as an alternative anchor to construct efficient SAM-based hole-selective contact (HSC) for PSCs. Theoretical calculations reveal that boric acid spontaneously chemisorbs onto indium tin oxide (ITO) surface with oxygen vacancies facilitating the adsorption progress. Spectroscopy and electrical measurements indicate that boric acid anchor significantly mitigates ITO corrosion. The excess boric acid containing molecules improves perovskite deposition and results in a coherent and well-passivated bottom interface, which boosts the fill factor (FF) performance for a variety of perovskite compositions. The optimal boric acid-anchoring HSC (MTPA-BA) can achieve power conversion efficiency close to 23% with a high FF of 85.2%. More importantly, the devices show improved stability: 90% of their initial efficiency is retained after 2400 h of storage (ISOS-D-1) or 400 h of operation (ISOS-L-1), which are 5-fold higher than those of phosphonic acid SAM-based devices. Acidity-weakened boric acid SAMs, which are friendly to ITO, exhibits well the great potential to improve the stability of the interface as well as the device.

Multifunctional Hybrid Interfacial Layers for High-Performance Inverted Perovskite Solar Cells

Challenges remain hindering the performance and stability of inverted perovskite solar cells (PSCs), particularly for the nonstable interface between lead halide perovskite and charge extraction metal oxide layer. Herein, a simple yet scalable interfacial strategy to facilitate the assemble of high-performance inverted PSCs and scale-up modules is reported. The hybrid interfacial layer containing self-assembly triphenylamine and conjugated poly(arylamine) simultaneously improves the chemical stability, charge extraction, and energy level alignment of hole-selective interface, meanwhile promoting perovskite crystallization. Consequently, the correspondent inverted PSCs and modules achieve remarkable power conversion efficiencies (PCEs) of 24.5% and 20.7% (aperture area of 19.4 cm² ), respectively. The PSCs maintain over 80% of its initial efficiency under one-sun equivalent illumination of 1200 h. This strategy is also effective to perovskite with various bandgaps, demonstrating the highest PCE of 19.6% for the 1.76-eV bandgap PSCs. Overall, this work provides a simple yet scalable interfacial strategy for obtaining state-of-the-art inverted PSCs and modules.

Tripodal Triazatruxene Derivative as a Face-On Oriented Hole-Collecting Monolayer for Efficient and Stable Inverted Perovskite Solar Cells

Hole-collecting monolayers have drawn attention in perovskite solar cell research due to their ease of processing, high performance, and good durability. Since molecules in the hole-collecting monolayer are typically composed of functionalized π-conjugated structures, hole extraction is expected to be more efficient when the π-cores are oriented face-on with respect to the adjacent surfaces. However, strategies for reliably controlling the molecular orientation in monolayers remain elusive. In this work, multiple phosphonic acid anchoring groups were used to control the molecular orientation of a series of triazatruxene derivatives chemisorbed on a transparent conducting oxide electrode surface. Using infrared reflection absorption spectroscopy and metastable atom electron spectroscopy, we found that multipodal derivatives align face-on to the electrode surface, while the monopodal counterpart adopts a more tilted configuration. The face-on orientation was found to facilitate hole extraction, leading to inverted perovskite solar cells with enhanced stability and high-power conversion efficiencies up to 23.0%.

Revisiting Alkoxysilane Assembly on Silica Surfaces: Grafting versus Homo-Condensation in Solution

Silica surface functionalization is often done through the condensation of functional silanes on silanols, silica surfaces' terminal groups. APTES, aminopropyltriethoxysilane, is widely used due to its assumed high reactivity with silanols, kinetically promoted by the catalytic action of the terminal amine function. Here, we revisit, based on a quantitative analysis by solid-state ²⁹Si NMR, the assembly of this silane on silica surfaces to investigate whether its presence results from grafting, i.e., hetero-condensation with silanol groups or from homo-condensation of silane molecules in solution leading to polycondensates physisorbed on silica. We investigate the interaction of APTES with a crystalline layered silicate, ilerite, and with amorphous nonporous silica. We also studied a second silane, cyanopropyltrichlorosilane (CPTCS), terminated with a nitrile group. Our results undoubtedly prove that while CPTCS is grafted on the silica surface, the presence of APTES on silica and silicate materials is only marginally associated with silanol consumption. The analysis of the signal related to silicon atoms from silanes (Tⁿ species) and those from silica (Qⁿ species) allowed for the accurate estimation of the extent of homo-condensation vs grafting based on the ratio of T-O-T/Q-O-T siloxane bridges. These findings deeply question the well-established certainties on APTES assembly on silica that should no longer be seen as grafting of alkoxysilane by hetero-condensation with silanol groups but more accurately as a homo-condensed network of silanes, predominantly physisorbed on the surface but including some sparse anchoring points to the surface involving less than 6% of the overall silanol groups.

Multifunctional antibacterial chitosan-based hydrogel coatings on Ti6Al4V biomaterial for biomedical implant applications

Among biomedical community, great efforts have been realized to develop antibacterial coatings that avoid implant-associated infections. To date, conventional mono-functional antibacterial strategies have not been effective enough for successful long-term implantations. Consequently, researchers have recently focused their attention on novel bifunctional or multifunctional antibacterial coatings, in which two or more antibacterial mechanisms interact synergistically. Thus, in this work different chitosan-based (CHI) hydrogel coatings were created on Ti6Al4V surface using genipin (Ti-CHIGP) and polyethylene glycol (Ti-CHIPEG) crosslinking agents. Hydrogel coatings demonstrated an exceptional in vivo biocompatibility plus a remarkable ability to promote cell proliferation and differentiation. Lastly, hydrogel coatings demonstrated an outstanding bacteria-repelling (17-28 % of S. aureus and 33-43 % of E. coli repelled) and contact killing (186-222 % of S. aureus and 72-83 % of E. coli damaged) ability. Such bifunctional antibacterial activity could be further improved by the controlled release of drugs resulting in powerful multifunctional antibacterial coatings.

A Comprehensive Review on Barium Titanate Nanoparticles as a Persuasive Piezoelectric Material for Biomedical Applications: Prospects and Challenges

Stimulation of cells with electrical cues is an imperative approach to interact with biological systems and has been exploited in clinical practices over a wide range of pathological ailments. This bioelectric interface has been extensively explored with the help of piezoelectric materials, leading to remarkable advancement in the past two decades. Among other members of this fraternity, colloidal perovskite barium titanate (BaTiO₃ ) has gained substantial interest due to its noteworthy properties which includes high dielectric constant and excellent ferroelectric properties along with acceptable biocompatibility. Significant progression is witnessed for BaTiO₃ nanoparticles (BaTiO₃ NPs) as potent candidates for biomedical applications and in wearable bioelectronics, making them a promising personal healthcare platform. The current review highlights the nanostructured piezoelectric bio interface of BaTiO₃ NPs in applications comprising drug delivery, tissue engineering, bioimaging, bioelectronics, and wearable devices. Particular attention has been dedicated toward the fabrication routes of BaTiO₃ NPs along with different approaches for its surface modifications. This review offers a comprehensive discussion on the utility of BaTiO₃ NPs as active devices rather than passive structural unit behaving as carriers for biomolecules. The employment of BaTiO₃ NPs presents new scenarios and opportunity in the vast field of nanomedicines for biomedical applications.

Expanding the Monolayer Scope for Nucleic Acid-Based Electrochemical Sensors Beyond Thiols on Gold: Alkylphosphonic Acids on ITO

Electrochemical biosensors are a powerful and rapidly evolving molecular monitoring technology. Evidenced by the success of the continuous glucose monitor in managing Type 1 Diabetes, these sensors are capable of precise, accurate measurements in unprocessed biological environments. Nucleic acid-based electrochemical sensors (NBEs) are a specific type of biosensor that employs the target binding and conformational dynamics of nucleic acids for signal transduction. Currently, the vast majority of NBEs are fabricated via self-assembly of alkylthiols on Au electrodes. However, this architecture is limited in scope, as Au electrodes are not universally deployable for all potential NBE applications. Here, to expand the repertoire of materials on which NBEs can be made, we describe the multistep procedure for creating sensing monolayers of alkylphosphonic acids on a conductive oxide surface. Using such monolayers on indium tin oxide (ITO)-coated glass slides, we couple redox reporter-modified nucleic acids and demonstrate signaling of procaine-binding NBE sensors in buffer and human serum. We investigate the operational stability of these NBE sensors to reveal faster signal loss relative to benchmark thiol-on-gold sensing layers, a result that arises due to poor stability of the underlying ITO. Finally, we discuss future directions to continue expansion of NBE sensor materials and applications.

Molecular Orientation of -PO3H2 and -COOH Functionalized Dyes on TiO2, Al2O3, ZrO2, and ITO: A Comparative Study

Modification of transparent metal oxide (MO_x) surfaces with organic monolayers is widely employed to tailor the properties of interfaces in organic electronic devices, and MO_x substrates modified with light-absorbing chromophores are a key component of dye-sensitized solar cells (DSSCs). The effects of an organic modifier on the performance of a MO_x-based device are frequently assessed by performing experiments on model monolayer|MO_x interfaces, where an "inert" MO_x (e.g., Al₂O₃) is used as a control for an "active" MO_x (e.g., TiO₂). An underlying assumption in these studies is that the structure of the MO_x-monolayer complex is similar between different metal oxides. The validity of this assumption was examined in the present study. Using UV-Vis attenuated total reflection spectroscopy, we measured the mean dipole tilt angle of 4,4'-(anthracene-9,10-diyl)bis(4,1-phenylene)diphosphonic acid (A1P) adsorbed on indium tin oxide (ITO), TiO₂, ZrO₂, and Al₂O₃. When the surface roughness of the MO_x substrate and the surface coverage (𝛤) of the A1P film were constant, the molecular orientation of A1P was the same on these substrates. The study was extended to 4,4'-(anthracene-9,10-diyl)bis(4,1-phenylene)dicarboxylic acid (A1C) adsorbed on the same group of MO_x substrates. The mean tilt angle of A1C and A1P films on ITO was the same, which is likely due the intermolecular interactions resulting from the high and approximately equal 𝛤 of both films. Comparing A1C films at the same 𝛤 on TiO₂ and Al₂O₃ having the same surface roughness, there was no difference in the mean tilt angle. MD simulations of A1C and A1P on TiO₂ produced nearly identical tilt angle distributions, which supports the experimental findings. This study provides first experimental support for the assumption that the structure of the MO_x-modifer film is the same on an "active" substrate vs. a "inert" control substrate.

Enhancement of electronic effects at a biomolecule-inorganic interface by multivalent interactions

The binding of peptides and proteins through multiple weak interactions is ubiquitous in nature. Biopanning has been used to "hijack" this multivalent binding for the functionalization of surfaces. For practical applications it is important to understand how multivalency influences the binding interactions and the resulting behaviour of the surface. Considering the importance of optimization of the electronic properties of surfaces in diverse electronic and optoelectronic applications, we study here the relation between the multivalency effect and the resulting modulation of the surface work function. We use 12-mer peptides, which were found to strongly bind to oxide surfaces, to functionalize indium tin oxide (ITO) surfaces. We show that the affinity of the peptides for the ITO surface, and concurrently the effect on the ITO work function, are linearly affected by the number of basic residues in the sequence. The multivalent binding interactions lead to a peptide crowding effect, and a stronger modulation of the work function for adodecapeptide than for a single basic amino acid functionalization. The bioderived molecular platform presented herein can pave the way to a novel approach to improve the performance of optoelectronic devices in an eco-friendly manner.

Biofunctionalization of Porous Titanium Oxide through Amino Acid Coupling for Biomaterial Design

Porous transition metal oxides are widely studied as biocompatible materials for the development of prosthetic implants. Resurfacing the oxide to improve the antibacterial properties of the material is still an open issue, as infections remain a major cause of implant failure. We investigated the functionalization of porous titanium oxide obtained by anodic oxidation with amino acids (Leucine) as a first step to couple antimicrobial peptides to the oxide surface. We adopted a two-step molecular deposition process as follows: self-assembly of aminophosphonates to titanium oxide followed by covalent coupling of Fmoc-Leucine to aminophosphonates. Molecular deposition was investigated step-by-step by Atomic Force Microscopy (AFM) and X-ray Photoemission Spectroscopy (XPS). Since the inherent high roughness of porous titanium hampers the analysis of molecular orientation on the surface, we resorted to parallel experiments on flat titanium oxide thin films. AFM nanoshaving experiments on aminophosphonates deposited on flat TiO₂ indicate the formation of an aminophosphonate monolayer while angle-resolved XPS analysis gives evidence of the formation of an oriented monolayer exposing the amine groups. The availability of the amine groups at the outer interface of the monolayer was confirmed on both flat and porous substrates by the following successful coupling with Fmoc-Leucine, as indicated by high-resolution XPS analysis.

Surface functionalization of inorganic nanoparticles with ligands: a necessary step for their utility

The importance of protecting inorganic nanoparticles with organic ligands and thus imparting the needed stabilization as colloidal dispersions for their potential applications is highlighted in this review.