Dye-sensitized NiO photocathode sensor based on signal-sensitive change strategy for MC-LR detection

A novel photoelectrochemical (PEC) sensor for the detection of microcystic toxins (MC-LR) was developed on the basis of signal-sensitive change strategy. NiO nanoarray as a basic photoactive material was grown directly on the ITO glass electrode via calcination after hydrothermal reaction, while dye N719 was used to sensitize the electrode for enhancing visible light absorption, and the first signal-on stage was obtained. In the meantime, p-type Cu2O was applied as the signal probe attached to probe DNA (DNA2) to improve the sensitivity, and the second "signal-on" stage appeared because of its synergistic effect with NiO nanoarrays. The PEC signal decreases after the target analyte MC-LR is modified on the electrode due to the stronger affinity between MC-LR and its complementary aptamer DNA; part of the Cu2O-DNA2 will dissociate from the electrode. This sensitive signal change strategy allows the detection limit of the MC-LR sensor to be as low as 1.7 pM, which offers an optional method for the sensitive and selective detection of other target molecules, with potential applications in environmental monitoring and toxin determination.

Slow hole diffusion limits the efficiency of p-type dye-sensitized solar cells based on the P1 dye

NiO electrodes are widely applied in p-type dye-sensitized solar cells (DSSCs) and photoelectrochemical cells, but due to excessive charge recombination, the efficiencies of these devices are still too low for commercial applications. To understand which factors induce charge recombination, we studied electrodes with a varying number of NiO layers in benchmark P1 p-DSSCs. We obtained the most efficient DSSCs with four layers of NiO (0.134%), and further insights into this optimum were obtained via dye loading studies and in operando photoelectrochemical immittance spectroscopy. These results revealed that more NiO layers led to an increasing light harvesting efficiency (η LH), but a decreasing hole collection efficiency (η CC), giving rise to the maximum efficiency at four NiO layers. The decreasing η CC with more NiO layers is caused by longer hole collection times, which ultimately limits the overall efficiency. Notably, the recombination rates were independent of the number of NiO layers, and similar to those observed in the more efficient n-type DSSC analogues, but hole collection was an order of magnitude slower. Therefore, with more NiO layers, the beneficial increase in η LH can no longer counteract the decrease in η CC due to slow hole collection, resulting in the overall efficiency of the solar cells to maximize at four NiO layers.

Ligand-Centered Photocatalytic Hydrogen Production in an Axially Capped Rh2(II,II) Paddlewheel Complex with Red Light

A new series of Rh2(II,II) complexes with the formula cis-[Rh2(DTolF)2(bpnp)(L)]2+, where bpnp = 2,7-bis(2-pyridyl)-1,8-naphthyridine, DTolF = N,N'-di(p-tolyl) formamidinate, and L = pdz (pyridazine; 2), cinn (cinnoline; 3), and bncn (benzo[c]cinnoline; 4), were synthesized from the precursor cis-[Rh2(DTolF)2(bpnp)(CH3CN)2]2+ (1). The first reduction couple in 2-4 is localized on the bpnp ligand at approximately -0.52 V vs Ag/AgCl in CH3CN (0.1 M TBAPF6), followed by reduction of the corresponding diazine ligand. Complex 1 exhibits a Rh2(δ*)/DTolF → bpnp(π*) metal/ligand-to-ligand charge-transfer (1ML-LCT) absorption with a maximum at 767 nm (ε = 1800 M-1 cm-1). This transition is also present in the spectra of 2-4, overlaid with the Rh2(δ*)/DTolF → L(π*) 1ML-LCT bands at 516 nm in 2 (L = pdz), 640 nm in 3 (L = cinn), and 721 nm in 4 (L = bncn). Complexes 2 and 3 exhibit Rh2(δ*)/DTolF → bpnp 3ML-LCT excited states with lifetimes, τ, of 3 and 5 ns, respectively, in CH3CN, whereas the lowest energy 3ML-LCT state in 4 is Rh2(δ*)/DTolF → bncn in nature with τ = 1 ns. Irradiation of 4 with 670 nm light in DMF in the presence of 0.1 M TsOH (p-toluene sulfonic acid) and 30 mM BNAH (1-benzyl-1,4-dihydronicotinamide) results in the production of H2 with a turnover number (TON) of 16 over 24 h. The axial capping of the Rh2(II,II) bimetallic core with the bpnp ligand prevents the formation of an Rh-H hydride intermediate. These results show that the observed photocatalytic reactivity is localized on the bncn ligand, representing the first example of ligand-centered H2 production.

Conversion of light into electricity in a semi-synthetic system based on photosynthetic bacterial chromatophores

Chromatophores (Chr) from photosynthetic nonsulfur purple bacterium Rhodobacter sphaeroides immobilized onto a Millipore membrane filter (MF) and sandwiched between two semiconductor indium tin oxide (ITO) electrodes (termed ITO|Chr - MF|ITO) have been used to measure voltage (ΔV) induced by continuous illumination. The maximum ΔV was detected in the presence of ascorbate / N,N,N'N'-tetramethyl-p-phenylenediamine couple, coenzyme UQ₀, disaccaride trehalose and antimycin A, an inhibitor of cytochrome bc₁ complex. In doing so, the light-induced electron transfer in the reaction centers was the major source of photovoltages. The stability of the voltage signal upon prolonged irradiation (>1 h) may be due to the maintenance of a conformation that is optimal for the functioning of integral protein complexes and stabilization of lipid bilayer membranes in the presence of trehalose. Retaining ∼70 % of the original photovoltage performance on the 30th day of storage at 23 °C in the dark under air was achieved after re-injection of fresh buffer (∼40 μL) containing redox mediators into the ITO|Chr - MF|ITO system. The approach we use is easy and can be extended to other biological intact systems (cells, thylakoid membranes) capable of converting energy of light.

Dye-sensitized solar cells strike back

Dye-sensitized solar cells (DSCs) are celebrating their 30th birthday and they are attracting a wealth of research efforts aimed at unleashing their full potential. In recent years, DSCs and dye-sensitized photoelectrochemical cells (DSPECs) have experienced a renaissance as the best technology for several niche applications that take advantage of DSCs' unique combination of properties: at low cost, they are composed of non-toxic materials, are colorful, transparent, and very efficient in low light conditions. This review summarizes the advancements in the field over the last decade, encompassing all aspects of the DSC technology: theoretical studies, characterization techniques, materials, applications as solar cells and as drivers for the synthesis of solar fuels, and commercialization efforts from various companies.

Towards sustainable and efficient p-type metal oxide semiconductor materials in dye-sensitised photocathodes for solar energy conversion

In order to meet the ever-growing global energy demand for affordable and clean energy, it is essential to provide this energy by renewable resources and consider the eco-efficiency of the production and abundance of the utilised materials. While this is seldom discussed in the case of technologies still in the research stage, addressing the issue of sustainability is key to push research in the right direction. Here we provide an overview of the current p-type metal oxide semiconductor materials in dye-sensitised photocathodes, considering element abundance, synthetic methods and large scale fabrication as well as the underlying physical properties that are necessary for efficient solar harvesting devices.

Computational Approaches to Photoelectrode Design through Molecular Functionalization for Enhanced Photoelectrochemical Water Splitting

Photoelectrochemical water splitting is a promising carbon-free approach to produce hydrogen from water. A photoelectrochemical cell consists of a semiconductor photoelectrode in contact with an aqueous electrolyte. Its performance is sensitive to properties of the photoelectrode/electrolyte interface, which may be tuned through functionalization of the photoelectrode surface with organic molecules. This can lead to improvements in the photoelectrode's properties. This Minireview summarizes key computational investigations on using molecular functionalization to modify photoelectrode stability, barrier height, and catalytic activity. It is discussed how first-principles density functional theory, first-principles molecular dynamics, and device modeling simulations can provide predictive insights and complement experimental investigations of functionalized photoelectrodes. Challenges and future directions in the computational modeling of functionalized photoelectrode/electrolyte interfaces within the context of experimental studies are also highlighted.

Promotional effect of Mn modification on DeNOx performance of Fe/nickel foam catalyst at low temperature

Manganese (Mn)-modified ferric oxide/nickel foam (Fe/Ni) catalysts were prepared using Ni as a carrier, Fe and Mn as active components to study NH₃-SCR of NO_x at low temperature. The effects of different Fe loads and Mn-modified Fe/Ni catalysts on the DeNO_x activity were investigated. Results show that when the amount of Fe is 10%, Fe/Ni catalyst has the highest NO_x conversion. For the Mn-modified Fe/Ni catalysts, the NO_x conversions firstly increase and then decrease with the Mn loading amount increasing. 3MnFe/Ni catalyst shows high NO_x conversions, which reach 98.4-100% at 120-240 °C. The characterization analyses reveal that Mn-modified Fe/Ni catalysts increase the FeO_x dispersion on Ni surface, improve significantly the valence ratio of the Fe³⁺/Fe²⁺, the content of lattice oxygen which promotes the catalyst storage and exchange oxygen capacity at low temperature, and the number of Brønsted active acid sites on the catalyst surface, and enhance the low-temperature redox capacity. These factors remarkably increase the NO_x conversions at low temperature. Especially, 3Mn10Fe/Ni catalyst not only has excellent DeNO_x activity but also has better water resistance. However, the anti-SO₂ poisoning performance needs to be improved. To further analyze the reason why different catalysts show different DeNO_x performance, the reaction kinetics was also explored.

Stabilization of a Cyclometalated Ruthenium Sensitizer on Nanocrystalline TiO2 by an Electrodeposited Covalent Layer

A cyclometalated ruthenium sensitizer 3 containing a triphenylamine unit was synthesized and immobilized on a nanocrystalline TiO₂ surface. By using oxidative electrochemical deposition, a covalent layer of a related cyclometalated ruthenium complex 2 was coupled to the top of dye 3. Electrochemical studies suggested that complex 2 was immobilized on the TiO₂/3 film surface by a tetraphenylbenzidine linker to form a dimer-like structure. The immobilization of 3 and 2 was further supported by absorption spectral analysis. The resulting electrodeposited TiO₂/(3+2) film displays significantly enhanced sensitizer stabilization toward basic aqueous NaOH solution with respect to the original TiO₂/3 film. The dye-sensitized solar cells with the TiO₂/(3+2) photoanode display a power conversion efficiency of 4.4%, which is slightly inferior to that with the TiO₂/3 film (5.1%) under the same measurement conditions.

Insights into the mechanism and aging of a noble-metal free H2-evolving dye-sensitized photocathode

Co-grafting of a cobalt diimine–dioxime catalyst and push–pull organic dye on NiO yields a photocathode evolving hydrogen from aqueous solution under sunlight, with equivalent performances compared to a dyad-based architecture using similar components.

Dye-sensitized photo-electrochemical cells (DS-PECs) form an emerging technology for the large-scale storage of solar energy in the form of (solar) fuels because of the low cost and ease of processing of their constitutive photoelectrode materials. Preparing such molecular photocathodes requires a well-controlled co-immobilization of molecular dyes and catalysts onto transparent semiconducting materials. Here we used a series of surface analysis techniques to describe the molecular assembly of a push–pull organic dye and a cobalt diimine–dioxime catalyst co-grafted on a p-type NiO electrode substrate. (Photo)electrochemical measurements allowed characterization of electron transfer processes within such an assembly and to demonstrate for the first time that a Co^I species is formed as the entry into the light-driven H₂ evolution mechanism of a dye-sensitized photocathode. This co-grafted noble-metal free H₂-evolving photocathode architecture displays similar performances to its covalent dye–catalyst counterpart based on the same catalytic moiety. Post-operando time-of-flight secondary ion mass spectrometry (ToF-SIMS) analysis of these photoelectrodes after extensive photoelectrochemical operation suggested decomposition pathways of the dye and triazole linkage used to graft the catalyst onto NiO, providing grounds for the design of optimized molecular DS-PEC components with increased robustness upon turnover.

ITO nanoparticle film as a hole-selective layer for PbS-sensitized photocathodes

This study opened a new door to fabricate semiconductor sensitized photocathodes using ITO as the holes transfer layer.

Catechol–TiO2 hybrids for photocatalytic H2 production and photocathode assembly

Charge-transfer dyes are explored for photocatalytic H₂ evolution (DSP) and dye-sensitised photoelectrochemical applications (DSPEC).

Competing charge transfer pathways at the photosystem II-electrode interface

The integration of the water-oxidation enzyme, photosystem II (PSII), into electrodes allows the electrons extracted from water-oxidation to be harnessed for enzyme characterization and driving novel endergonic reactions. However, PSII continues to underperform in integrated photoelectrochemical systems despite extensive optimization efforts. Here, we performed protein-film photoelectrochemistry on spinach and Thermosynechococcus elongatus PSII, and identified a competing charge transfer pathway at the enzyme-electrode interface that short-circuits the known water-oxidation pathway: photo-induced O₂ reduction occurring at the chlorophyll pigments. This undesirable pathway is promoted by the embedment of PSII in an electron-conducting matrix, a common strategy of enzyme immobilization. Anaerobicity helps to recover the PSII photoresponses, and unmasked the onset potentials relating to the Q_A/Q_B charge transfer process. These findings have imparted a fuller understanding of the charge transfer pathways within PSII and at photosystem-electrode interfaces, which will lead to more rational design of pigment-containing photoelectrodes in general.

Finding the Way to Solar Fuels with Dye-Sensitized Photoelectrosynthesis Cells

The dye-sensitized photoelectrosynthesis cell (DSPEC) integrates high bandgap, nanoparticle oxide semiconductors with the light-absorbing and catalytic properties of designed chromophore-catalyst assemblies. The goals are photoelectrochemical water splitting into hydrogen and oxygen and reduction of CO₂ by water to give oxygen and carbon-based fuels. Solar-driven water oxidation occurs at a photoanode and water or CO₂ reduction at a cathode or photocathode initiated by molecular-level light absorption. Light absorption is followed by electron or hole injection, catalyst activation, and catalytic water oxidation or water/CO₂ reduction. The DSPEC is of recent origin but significant progress has been made. It has the potential to play an important role in our energy future.

High Color-Purity Green, Orange, and Red Light-Emitting Diodes Based on Chemically Functionalized Graphene Quantum Dots

Chemically derived graphene quantum dots (GQDs) to date have showed very broad emission linewidth due to many kinds of chemical bondings with different energy levels, which significantly degrades the color purity and color tunability. Here, we show that use of aniline derivatives to chemically functionalize GQDs generates new extrinsic energy levels that lead to photoluminescence of very narrow linewidths. We use transient absorption and time-resolved photoluminescence spectroscopies to study the electronic structures and related electronic transitions of our GQDs, which reveals that their underlying carrier dynamics is strongly related to the chemical properties of aniline derivatives. Using these functionalized GQDs as lumophores, we fabricate light-emitting didoes (LEDs) that exhibit green, orange, and red electroluminescence that has high color purity. The maximum current efficiency of 3.47 cd A⁻¹ and external quantum efficiency of 1.28% are recorded with our LEDs; these are the highest values ever reported for LEDs based on carbon-nanoparticle phosphors. This functionalization of GQDs with aniline derivatives represents a new method to fabricate LEDs that produce natural color.

Low-Temperature Selective Catalytic Reduction of NO with NH₃ over Mn₂O₃-Doped Fe₂O₃ Hexagonal Microsheets

Mn2O3-doped Fe2O3 hexagonal microsheets were prepared for the low-temperature selective catalytic reduction (SCR) of NO with NH3. These hexagonal microsheets were characterized by SEM, TEM, XRD, BET, XPS, NH3-TPD, H2-TPR, and in situ DRIFT and were shown to exhibit a considerable uniform hexagonal microsheet structure and excellent low temperature SCR efficiency. When doped with different Mn molar ratios, Mn2O3 was detected in the Fe2O3 hexagonal microsheets based on the XRD results without the presence of other MnOX species. In addition, the hexagonal microsheets with a Mn/Fe molar ratio of 0.2 showed the best SCR removal performance among the materials, where a 98% NO conversion ratio at 200 °C at a space velocity of 30,000 h(-1) was obtained. Meanwhile, excellent tolerances to H2O and SO2, as well as high thermal stability, were obtained in Mn2O3-doped Fe2O3 hexagonal microsheets. Moreover, on the basis of the XPS and in situ DRIFT results, it can be suggested that coupled Mn2O3 nanocrystals played a key role at low temperatures and produced a possible redox reaction mechanism in the SCR process.

Cyclometalated ruthenium(ii) complexes with bis(benzimidazolyl)benzene for dye-sensitized solar cells

The length of alkyl chains on the benzimidazole rings of cyclometalated ruthenium dyes is critical to the DSSC performance.